# Restricted domain for shell processes spawned by init.
# Normally these are shell commands or scripts invoked via sh
# from an init*.rc file.  No service should ever run in this domain.
type qti_init_shell, domain;
domain_auto_trans(init, shell_exec, qti_init_shell)

# For executing init shell scripts (init.qcom.early_boot.sh)
allow qti_init_shell rootfs:file entrypoint;

# For getting idle_time value
# this is needed for dynamic_fps and bw_mode_bitmap
allow qti_init_shell sysfs_graphics:file {rw_file_perms setattr};
allow qti_init_shell sysfs:file setattr;

allow qti_init_shell persist_file:dir w_dir_perms;
allow qti_init_shell persist_file:file create_file_perms;
allow qti_init_shell smd_device:chr_file rw_file_perms;

# Run helpers from / or /system without changing domain.
allow qti_init_shell { system_file rootfs shell_exec }:file execute_no_trans;

# For accessing fmradio device node
# For accessing qdss_device device node
allow qti_init_shell { fm_radio_device qdss_device }:chr_file r_file_perms;
#give permission to read/write fm dir for calibration file
allow qti_init_shell fm_data_file: dir rw_dir_perms;
# create/open, read/write permission for fm calibration file.
allow qti_init_shell fm_data_file: file create_file_perms;

# for insmod of iris ko, this is needed.
#dac_read/override is needed for scripts to do chown/mkdir which is
#needed by most of the services
# fowner and fsetid are needed for chmod display nodes.
allow qti_init_shell self:capability {
    sys_module
    net_admin
    chown
    fowner
    fsetid
    dac_override
    dac_read_search
};

# For  property starting with hw
# freq_prop - for setting frequency from postboot script
# perfd_prop - for setting ctl.perfd property from postboot script
# bluetooth_prop - for setting bt related properties from postboot script
# uicc_prop - for access to UICC property
# ctl_qmuxd_prop/ctl_netmgrd_prop - Needed in order to set properties on qmuxd and netmgrd processes
allow qti_init_shell {
    system_prop
    freq_prop
    perfd_prop
    bluetooth_prop
    config_prop
    sensors_prop
    msm_irqbalance_prop
    ipacm_prop
    ipacm-diag_prop
    qti_prop
    ctl_rildaemon_prop
    uicc_prop
    ctl_qmuxd_prop
    ctl_netmgrd_prop
    sf_lcd_density_prop
    # Needed for starting console in userdebug mode
    userdebug_or_eng(`ctl_console_prop')
}:property_service set;

allow qti_init_shell efs_boot_dev:blk_file r_file_perms;

# For hci_comm_init
allow qti_init_shell serial_device:chr_file rw_file_perms;

# Allow property changes
unix_socket_connect(qti_init_shell, property, init)

allow qti_init_shell {
    sysfs
    sysfs_devices_system_cpu
    sysfs_thermal
    sysfs_lowmemorykiller
}:file w_file_perms;

r_dir_file(qti_init_shell, sysfs_thermal)
allow qti_init_shell sysfs_socinfo:file write;

# Check if /dev/sensors or /dev/msm_dsps present
allow qti_init_shell sensors_data_file:dir r_dir_perms;
allow qti_init_shell sensors_device:chr_file r_file_perms;

# To start sensors for DSPS enabled platforms
r_dir_file(qti_init_shell, persist_file)
r_dir_file(qti_init_shell, sensors_persist_file)
allow qti_init_shell sensors_persist_file:file setattr;

# To start of selected USF based calculators
r_dir_file(qti_init_shell, usf_data_file)
allow qti_init_shell usf_data_file:file w_file_perms;
r_dir_file(qti_init_shell, persist_usf_file)
allow qti_init_shell usf_data_file:dir create_dir_perms;
allow qti_init_shell usf_data_file:{ file lnk_file } create_file_perms;

# To check if /system/bin/msm_irqbalance is persent in the device
allow qti_init_shell msm_irqbalanced_exec:file getattr;

# To write to /data/system/perfd
allow qti_init_shell mpctl_data_file:dir w_dir_perms;
allow qti_init_shell mpctl_data_file:file { write getattr unlink };

allow qti_init_shell { proc proc_net }:file write;

allow qti_init_shell radio_data_file:dir create_dir_perms;
allow qti_init_shell radio_data_file:file create_file_perms;

allow qti_init_shell firmware_file:dir r_dir_perms;
allow qti_init_shell graphics_device:dir create_dir_perms;
allow qti_init_shell graphics_device:lnk_file create_file_perms;

# To create sensor dir inside /data/misc/
allow qti_init_shell system_data_file:dir create_dir_perms;