WCNSS_qcom_cfg.ini - fp2-dev/device/asus/flo - Gitiles

 # This file allows user to override the factory
 # defaults for the WLAN Driver

 # Enable IMPS or not
 gEnableImps=1

 # Enable/Disable Idle Scan
 gEnableIdleScan=0

 # Increase sleep duration (seconds) during IMPS
 # 0 implies no periodic wake up from IMPS. Periodic wakeup is
 # unnecessary if Idle Scan is disabled.
 gImpsModSleepTime=0

 # Enable BMPS or not
 gEnableBmps=1

 # Enable Close Loop or not
 gEnableCloseLoop=1

 # Enable suspend or not
 # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
 gEnableSuspend=3

 # Phy Mode (auto, b, g, n, etc)
 gDot11Mode=0

 # Handoff Enable(1) Disable(0)
 gEnableHandoff=0

 # CSR Roaming Enable(1) Disable(0)
 gRoamingTime=0

 # Assigned MAC Addresses - This will be used until NV items are in place
 # Each byte of MAC address is represented in Hex format as XX
 Intf0MacAddress=000AF58989FF
 Intf1MacAddress=000AF58989FE
 Intf2MacAddress=000AF58989FD
 Intf3MacAddress=000AF58989FC

 # UAPSD service interval for VO,VI, BE, BK traffic
 InfraUapsdVoSrvIntv=0
 InfraUapsdViSrvIntv=0
 InfraUapsdBeSrvIntv=0
 InfraUapsdBkSrvIntv=0

 # Enable Firmware RSSI monitoring for roaming
 gEnableFWRssiMonitoring=1

 # Make 1x1 the default antenna configuration
 gNumRxAnt=1

 # Beacon filtering frequency (unit in beacon intervals)
 gNthBeaconFilter=50

 # Enable WAPI or not
 # WAPIIsEnabled=0

 # Flags to filter Mcast and Bcast RX packets.
 # Value 0: No filtering, 1: Filter all Multicast.
 # 2: Filter all Broadcast. 3: Filter all Mcast and Bcast
 McastBcastFilter=3

 #Flag to enable HostARPOffload feature or not
 hostArpOffload=0

 #SoftAP Related Parameters
 # AP MAc addr (obsolete)
 gAPMacAddr=000AF58989EF

 # Enable Random BSSID
 gEnableApRandomBssid=1

 # 802.11n Protection flag
 gEnableApProt=1

 # Enable OBSS protection
 gEnableApOBSSProt=0

 # Enable/Disable UAPSD for SoftAP
 gEnableApUapsd=1

 # Fixed Rate
 gFixedRate=0

 # Maximum Tx power
 # gTxPowerCap=30

 # Fragmentation Threshold
 # gFragmentationThreshold=2346

 # RTS threshold
 RTSThreshold=2347

 # Intra-BSS forward
 gDisableIntraBssFwd=0

 # WMM Enable/Disable
 WmmIsEnabled=0

 # 802.11d support
 g11dSupportEnabled=1

 # CCX Support and fast transition
 CcxEnabled=0
 FastTransitionEnabled=1
 ImplicitQosIsEnabled=1
 gNeighborScanTimerPeriod=200

 gNeighborLookupThreshold=76
 gNeighborReassocThreshold=81

 gNeighborScanChannelMinTime=20
 gNeighborScanChannelMaxTime=30
 gMaxNeighborReqTries=3

 # Legacy (non-CCX, non-802.11r) Fast Roaming Support
 # To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1
 # To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0
 FastRoamEnabled=1

 #Check if the AP to which we are roaming is better than current AP in terms of RSSI.
 #Checking is disabled if set to Zero.Otherwise it will use this value as to how better
 #the RSSI of the new/roamable AP should be for roaming
 RoamRssiDiff=3

 #Configure the RSSI gap that will be used to partition/categorize width of
 #each  individual category (aka bucket).
 gRssiCatGap=5

 # SAP Country code
 # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
 # Example
 #   US Indoor, USI
 #   Korea Outdoor, KRO
 #   Japan without optional byte, JP
 #   France without optional byte, FR
 #gAPCntryCode=USI

 #Short Guard Interval Enable/disable
 gShortGI20Mhz=1
 gShortGI40Mhz=1

 #Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
 gAPAutoShutOff=0

 # SAP auto channel selection configuration
 # 0 = disable auto channel selection
 # 1 = enable auto channel selection, channel provided by supplicant will be ignored
 gApAutoChannelSelection=0

 # Listen Energy Detect Mode Configuration
 # Valid values 0-128
 # 128 means disable Energy Detect feature
 # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
 # 10-128 are reserved.
 # The EDET threshold mapping is as follows in 3dB step:
 # 0 = -60 dBm
 # 1 = -63 dBm
 # 2 = -66 dBm
 # ...
 # 7 = -81 dBm
 # 8 = -84 dBm
 # 9 = -87 dBm
 # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
 #
 #  Range Loss  (dB)  =  EDET threshold level (dBm) + 97 dBm.
 #
 gEnablePhyAgcListenMode=128

 #Preferred band (both or 2.4 only or 5 only)
 BandCapability=0

 #Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM
 gEnableModulatedDTIM=3

 #Beacon Early Termination (1 = enable the BET feature, 0 = disable)
 enableBeaconEarlyTermination=1
 beaconEarlyTerminationWakeInterval=11

 #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
 gEnableBtAmp=0

 #Preferred channel to start BT AMP AP mode (0 means, any channel)
 BtAmpPreferredChannel=0

 #SOFTAP Channel Range selection
 gAPChannelSelectStartChannel=1
 gAPChannelSelectEndChannel=11

 #SOFTAP Channel Range selection Operating band
 # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
 gAPChannelSelectOperatingBand=0

 #Enable Keep alive with non-zero period value
 gStaKeepAlivePeriod = 25

 #If set will start with active scan after driver load, otherwise will start with
 #passive scan to find out the domain
 gEnableBypass11d=1

 #If set to 0, will not scan DFS channels
 gEnableDFSChnlScan=0

 # Enable logp/SSR
 gEnableLogp=1

 # Disable HT40
 gChannelBondingMode5GHz=0

 # Enable Automatic Tx Power control
 gEnableAutomaticTxPowerControl=1

 # Derive P2P MAC address from primary MAC address
 isP2pDeviceAddrAdministrated=1

 # Disable channel 165 for Indonesia
 gIgnore_Chan165=1

 END
 # Note: Configuration parser would not read anything past the END marker
	# This file allows user to override the factory
	# defaults for the WLAN Driver

	# Enable IMPS or not
	gEnableImps=1

	# Enable/Disable Idle Scan
	gEnableIdleScan=0

	# Increase sleep duration (seconds) during IMPS
	# 0 implies no periodic wake up from IMPS. Periodic wakeup is
	# unnecessary if Idle Scan is disabled.
	gImpsModSleepTime=0

	# Enable BMPS or not
	gEnableBmps=1

	# Enable Close Loop or not
	gEnableCloseLoop=1

	# Enable suspend or not
	# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
	gEnableSuspend=3

	# Phy Mode (auto, b, g, n, etc)
	gDot11Mode=0

	# Handoff Enable(1) Disable(0)
	gEnableHandoff=0

	# CSR Roaming Enable(1) Disable(0)
	gRoamingTime=0

	# Assigned MAC Addresses - This will be used until NV items are in place
	# Each byte of MAC address is represented in Hex format as XX
	Intf0MacAddress=000AF58989FF
	Intf1MacAddress=000AF58989FE
	Intf2MacAddress=000AF58989FD
	Intf3MacAddress=000AF58989FC

	# UAPSD service interval for VO,VI, BE, BK traffic
	InfraUapsdVoSrvIntv=0
	InfraUapsdViSrvIntv=0
	InfraUapsdBeSrvIntv=0
	InfraUapsdBkSrvIntv=0

	# Enable Firmware RSSI monitoring for roaming
	gEnableFWRssiMonitoring=1

	# Make 1x1 the default antenna configuration
	gNumRxAnt=1

	# Beacon filtering frequency (unit in beacon intervals)
	gNthBeaconFilter=50

	# Enable WAPI or not
	# WAPIIsEnabled=0

	# Flags to filter Mcast and Bcast RX packets.
	# Value 0: No filtering, 1: Filter all Multicast.
	# 2: Filter all Broadcast. 3: Filter all Mcast and Bcast
	McastBcastFilter=3

	#Flag to enable HostARPOffload feature or not
	hostArpOffload=0

	#SoftAP Related Parameters
	# AP MAc addr (obsolete)
	gAPMacAddr=000AF58989EF

	# Enable Random BSSID
	gEnableApRandomBssid=1

	# 802.11n Protection flag
	gEnableApProt=1

	# Enable OBSS protection
	gEnableApOBSSProt=0

	# Enable/Disable UAPSD for SoftAP
	gEnableApUapsd=1

	# Fixed Rate
	gFixedRate=0

	# Maximum Tx power
	# gTxPowerCap=30

	# Fragmentation Threshold
	# gFragmentationThreshold=2346

	# RTS threshold
	RTSThreshold=2347

	# Intra-BSS forward
	gDisableIntraBssFwd=0

	# WMM Enable/Disable
	WmmIsEnabled=0

	# 802.11d support
	g11dSupportEnabled=1

	# CCX Support and fast transition
	CcxEnabled=0
	FastTransitionEnabled=1
	ImplicitQosIsEnabled=1
	gNeighborScanTimerPeriod=200

	gNeighborLookupThreshold=76
	gNeighborReassocThreshold=81

	gNeighborScanChannelMinTime=20
	gNeighborScanChannelMaxTime=30
	gMaxNeighborReqTries=3

	# Legacy (non-CCX, non-802.11r) Fast Roaming Support
	# To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1
	# To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0
	FastRoamEnabled=1

	#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
	#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
	#the RSSI of the new/roamable AP should be for roaming
	RoamRssiDiff=3

	#Configure the RSSI gap that will be used to partition/categorize width of
	#each individual category (aka bucket).
	gRssiCatGap=5

	# SAP Country code
	# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
	# Example
	# US Indoor, USI
	# Korea Outdoor, KRO
	# Japan without optional byte, JP
	# France without optional byte, FR
	#gAPCntryCode=USI

	#Short Guard Interval Enable/disable
	gShortGI20Mhz=1
	gShortGI40Mhz=1

	#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
	gAPAutoShutOff=0

	# SAP auto channel selection configuration
	# 0 = disable auto channel selection
	# 1 = enable auto channel selection, channel provided by supplicant will be ignored
	gApAutoChannelSelection=0

	# Listen Energy Detect Mode Configuration
	# Valid values 0-128
	# 128 means disable Energy Detect feature
	# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
	# 10-128 are reserved.
	# The EDET threshold mapping is as follows in 3dB step:
	# 0 = -60 dBm
	# 1 = -63 dBm
	# 2 = -66 dBm
	# ...
	# 7 = -81 dBm
	# 8 = -84 dBm
	# 9 = -87 dBm
	# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
	#
	# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
	#
	gEnablePhyAgcListenMode=128

	#Preferred band (both or 2.4 only or 5 only)
	BandCapability=0

	#Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM
	gEnableModulatedDTIM=3

	#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
	enableBeaconEarlyTermination=1
	beaconEarlyTerminationWakeInterval=11

	#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
	gEnableBtAmp=0

	#Preferred channel to start BT AMP AP mode (0 means, any channel)
	BtAmpPreferredChannel=0

	#SOFTAP Channel Range selection
	gAPChannelSelectStartChannel=1
	gAPChannelSelectEndChannel=11

	#SOFTAP Channel Range selection Operating band
	# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
	gAPChannelSelectOperatingBand=0

	#Enable Keep alive with non-zero period value
	gStaKeepAlivePeriod = 25

	#If set will start with active scan after driver load, otherwise will start with
	#passive scan to find out the domain
	gEnableBypass11d=1

	#If set to 0, will not scan DFS channels
	gEnableDFSChnlScan=0

	# Enable logp/SSR
	gEnableLogp=1

	# Disable HT40
	gChannelBondingMode5GHz=0

	# Enable Automatic Tx Power control
	gEnableAutomaticTxPowerControl=1

	# Derive P2P MAC address from primary MAC address
	isP2pDeviceAddrAdministrated=1

	# Disable channel 165 for Indonesia
	gIgnore_Chan165=1

	END
	# Note: Configuration parser would not read anything past the END marker