Use menuconfig objects: W1
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/w1/Kconfig b/drivers/w1/Kconfig
index ca75b3a..6854fd6 100644
--- a/drivers/w1/Kconfig
+++ b/drivers/w1/Kconfig
@@ -1,8 +1,6 @@
-menu "Dallas's 1-wire bus"
- depends on HAS_IOMEM
-
-config W1
+menuconfig W1
tristate "Dallas's 1-wire support"
+ depends on HAS_IOMEM
---help---
Dallas' 1-wire bus is useful to connect slow 1-pin devices
such as iButtons and thermal sensors.
@@ -12,8 +10,10 @@
This W1 support can also be built as a module. If so, the module
will be called wire.ko.
+if W1
+
config W1_CON
- depends on CONNECTOR && W1
+ depends on CONNECTOR
bool "Userspace communication over connector"
default y
--- help ---
@@ -27,4 +27,4 @@
source drivers/w1/masters/Kconfig
source drivers/w1/slaves/Kconfig
-endmenu
+endif # W1
diff --git a/drivers/w1/masters/Kconfig b/drivers/w1/masters/Kconfig
index 8f77933..8236d44 100644
--- a/drivers/w1/masters/Kconfig
+++ b/drivers/w1/masters/Kconfig
@@ -3,11 +3,10 @@
#
menu "1-wire Bus Masters"
- depends on W1
config W1_MASTER_MATROX
tristate "Matrox G400 transport layer for 1-wire"
- depends on W1 && PCI
+ depends on PCI
help
Say Y here if you want to communicate with your 1-wire devices
using Matrox's G400 GPIO pins.
@@ -17,7 +16,7 @@
config W1_MASTER_DS2490
tristate "DS2490 USB <-> W1 transport layer for 1-wire"
- depends on W1 && USB
+ depends on USB
help
Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges,
for example DS9490*.
@@ -27,7 +26,7 @@
config W1_MASTER_DS2482
tristate "Maxim DS2482 I2C to 1-Wire bridge"
- depends on I2C && W1 && EXPERIMENTAL
+ depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for the Maxim DS2482
I2C to 1-Wire bridge.
diff --git a/drivers/w1/slaves/Kconfig b/drivers/w1/slaves/Kconfig
index df95d6c..3df29a1 100644
--- a/drivers/w1/slaves/Kconfig
+++ b/drivers/w1/slaves/Kconfig
@@ -3,25 +3,21 @@
#
menu "1-wire Slaves"
- depends on W1
config W1_SLAVE_THERM
tristate "Thermal family implementation"
- depends on W1
help
Say Y here if you want to connect 1-wire thermal sensors to your
wire.
config W1_SLAVE_SMEM
tristate "Simple 64bit memory family implementation"
- depends on W1
help
Say Y here if you want to connect 1-wire
simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire.
config W1_SLAVE_DS2433
tristate "4kb EEPROM family support (DS2433)"
- depends on W1
help
Say Y here if you want to use a 1-wire
4kb EEPROM family device (DS2433).