drivers/ata/pata_cs5520.c - fp2-dev/kernel/msm - Gitiles

 /*
  *	IDE tuning and bus mastering support for the CS5510/CS5520
  *	chipsets
  *
  *	The CS5510/CS5520 are slightly unusual devices. Unlike the
  *	typical IDE controllers they do bus mastering with the drive in
  *	PIO mode and smarter silicon.
  *
  *	The practical upshot of this is that we must always tune the
  *	drive for the right PIO mode. We must also ignore all the blacklists
  *	and the drive bus mastering DMA information. Also to confuse matters
  *	further we can do DMA on PIO only drives.
  *
  *	DMA on the 5510 also requires we disable_hlt() during DMA on early
  *	revisions.
  *
  *	*** This driver is strictly experimental ***
  *
  *	(c) Copyright Red Hat Inc 2002
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
  * Free Software Foundation; either version 2, or (at your option) any
  * later version.
  *
  * This program is distributed in the hope that it will be useful, but
  * WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  * General Public License for more details.
  *
  * Documentation:
  *	Not publically available.
  */
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/init.h>
 #include <linux/blkdev.h>
 #include <linux/delay.h>
 #include <scsi/scsi_host.h>
 #include <linux/libata.h>

 #define DRV_NAME	"pata_cs5520"
 #define DRV_VERSION	"0.6.5"

 struct pio_clocks
 {
 	int address;
 	int assert;
 	int recovery;
 };

 static const struct pio_clocks cs5520_pio_clocks[]={
 	{3, 6, 11},
 	{2, 5, 6},
 	{1, 4, 3},
 	{1, 3, 2},
 	{1, 2, 1}
 };

 /**
  *	cs5520_set_timings	-	program PIO timings
  *	@ap: ATA port
  *	@adev: ATA device
  *
  *	Program the PIO mode timings for the controller according to the pio
  *	clocking table.
  */

 static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	int slave = adev->devno;

 	pio -= XFER_PIO_0;

 	/* Channel command timing */
 	pci_write_config_byte(pdev, 0x62 + ap->port_no,
 				(cs5520_pio_clocks[pio].recovery << 4) |
 				(cs5520_pio_clocks[pio].assert));
 	/* FIXME: should these use address ? */
 	/* Read command timing */
 	pci_write_config_byte(pdev, 0x64 +  4*ap->port_no + slave,
 				(cs5520_pio_clocks[pio].recovery << 4) |
 				(cs5520_pio_clocks[pio].assert));
 	/* Write command timing */
 	pci_write_config_byte(pdev, 0x66 +  4*ap->port_no + slave,
 				(cs5520_pio_clocks[pio].recovery << 4) |
 				(cs5520_pio_clocks[pio].assert));
 }

 /**
  *	cs5520_enable_dma	-	turn on DMA bits
  *
  *	Turn on the DMA bits for this disk. Needed because the BIOS probably
  *	has not done the work for us. Belongs in the core SATA code.
  */

 static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev)
 {
 	/* Set the DMA enable/disable flag */
 	u8 reg = ioread8(ap->ioaddr.bmdma_addr + 0x02);
 	reg |= 1<<(adev->devno + 5);
 	iowrite8(reg, ap->ioaddr.bmdma_addr + 0x02);
 }

 /**
  *	cs5520_set_dmamode	-	program DMA timings
  *	@ap: ATA port
  *	@adev: ATA device
  *
  *	Program the DMA mode timings for the controller according to the pio
  *	clocking table. Note that this device sets the DMA timings to PIO
  *	mode values. This may seem bizarre but the 5520 architecture talks
  *	PIO mode to the disk and DMA mode to the controller so the underlying
  *	transfers are PIO timed.
  */

 static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 {
 	static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 };
 	cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]);
 	cs5520_enable_dma(ap, adev);
 }

 /**
  *	cs5520_set_piomode	-	program PIO timings
  *	@ap: ATA port
  *	@adev: ATA device
  *
  *	Program the PIO mode timings for the controller according to the pio
  *	clocking table. We know pio_mode will equal dma_mode because of the
  *	CS5520 architecture. At least once we turned DMA on and wrote a
  *	mode setter.
  */

 static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
 {
 	cs5520_set_timings(ap, adev, adev->pio_mode);
 }

 static struct scsi_host_template cs5520_sht = {
 	.module			= THIS_MODULE,
 	.name			= DRV_NAME,
 	.ioctl			= ata_scsi_ioctl,
 	.queuecommand		= ata_scsi_queuecmd,
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_DUMB_MAX_PRD,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
 	.proc_name		= DRV_NAME,
 	.dma_boundary		= ATA_DMA_BOUNDARY,
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
 };

 static struct ata_port_operations cs5520_port_ops = {
 	.port_disable		= ata_port_disable,
 	.set_piomode		= cs5520_set_piomode,
 	.set_dmamode		= cs5520_set_dmamode,

 	.tf_load		= ata_tf_load,
 	.tf_read		= ata_tf_read,
 	.check_status		= ata_check_status,
 	.exec_command		= ata_exec_command,
 	.dev_select		= ata_std_dev_select,

 	.freeze			= ata_bmdma_freeze,
 	.thaw			= ata_bmdma_thaw,
 	.error_handler		= ata_bmdma_error_handler,
 	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
 	.cable_detect		= ata_cable_40wire,

 	.bmdma_setup		= ata_bmdma_setup,
 	.bmdma_start		= ata_bmdma_start,
 	.bmdma_stop		= ata_bmdma_stop,
 	.bmdma_status		= ata_bmdma_status,
 	.qc_prep		= ata_dumb_qc_prep,
 	.qc_issue		= ata_qc_issue_prot,
 	.data_xfer		= ata_data_xfer,

 	.irq_clear		= ata_bmdma_irq_clear,
 	.irq_on			= ata_irq_on,
 	.irq_ack		= ata_irq_ack,

 	.port_start		= ata_port_start,
 };

 static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct ata_port_info pi = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= 0x1f,
 		.port_ops	= &cs5520_port_ops,
 	};
 	const struct ata_port_info *ppi[2];
 	u8 pcicfg;
 	void *iomap[5];
 	struct ata_host *host;
 	struct ata_ioports *ioaddr;
 	int i, rc;

 	/* IDE port enable bits */
 	pci_read_config_byte(pdev, 0x60, &pcicfg);

 	/* Check if the ATA ports are enabled */
 	if ((pcicfg & 3) == 0)
 		return -ENODEV;

 	ppi[0] = ppi[1] = &ata_dummy_port_info;
 	if (pcicfg & 1)
 		ppi[0] = &pi;
 	if (pcicfg & 2)
 		ppi[1] = &pi;

 	if ((pcicfg & 0x40) == 0) {
 		dev_printk(KERN_WARNING, &pdev->dev,
 			   "DMA mode disabled. Enabling.\n");
 		pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
 	}

 	pi.mwdma_mask = id->driver_data;

 	host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
 	if (!host)
 		return -ENOMEM;

 	/* Perform set up for DMA */
 	if (pci_enable_device_bars(pdev, 1<<2)) {
 		printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
 		return -ENODEV;
 	}

 	if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
 		printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
 		return -ENODEV;
 	}
 	if (pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK)) {
 		printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
 		return -ENODEV;
 	}

 	/* Map IO ports and initialize host accordingly */
 	iomap[0] = devm_ioport_map(&pdev->dev, 0x1F0, 8);
 	iomap[1] = devm_ioport_map(&pdev->dev, 0x3F6, 1);
 	iomap[2] = devm_ioport_map(&pdev->dev, 0x170, 8);
 	iomap[3] = devm_ioport_map(&pdev->dev, 0x376, 1);
 	iomap[4] = pcim_iomap(pdev, 2, 0);

 	if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
 		return -ENOMEM;

 	ioaddr = &host->ports[0]->ioaddr;
 	ioaddr->cmd_addr = iomap[0];
 	ioaddr->ctl_addr = iomap[1];
 	ioaddr->altstatus_addr = iomap[1];
 	ioaddr->bmdma_addr = iomap[4];
 	ata_std_ports(ioaddr);

 	ioaddr = &host->ports[1]->ioaddr;
 	ioaddr->cmd_addr = iomap[2];
 	ioaddr->ctl_addr = iomap[3];
 	ioaddr->altstatus_addr = iomap[3];
 	ioaddr->bmdma_addr = iomap[4] + 8;
 	ata_std_ports(ioaddr);

 	/* activate the host */
 	pci_set_master(pdev);
 	rc = ata_host_start(host);
 	if (rc)
 		return rc;

 	for (i = 0; i < 2; i++) {
 		static const int irq[] = { 14, 15 };
 		struct ata_port *ap = host->ports[0];

 		if (ata_port_is_dummy(ap))
 			continue;

 		rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
 				      ata_interrupt, 0, DRV_NAME, host);
 		if (rc)
 			return rc;

 		if (i == 0)
 			host->irq = irq[0];
 		else
 			host->irq2 = irq[1];
 	}

 	return ata_host_register(host, &cs5520_sht);
 }

 /**
  *	cs5520_remove_one	-	device unload
  *	@pdev: PCI device being removed
  *
  *	Handle an unplug/unload event for a PCI device. Unload the
  *	PCI driver but do not use the default handler as we manage
  *	resources ourself and *MUST NOT* disable the device as it has
  *	other functions.
  */

 static void __devexit cs5520_remove_one(struct pci_dev *pdev)
 {
 	struct device *dev = pci_dev_to_dev(pdev);
 	struct ata_host *host = dev_get_drvdata(dev);

 	ata_host_detach(host);
 }

 #ifdef CONFIG_PM
 /**
  *	cs5520_reinit_one	-	device resume
  *	@pdev: PCI device
  *
  *	Do any reconfiguration work needed by a resume from RAM. We need
  *	to restore DMA mode support on BIOSen which disabled it
  */

 static int cs5520_reinit_one(struct pci_dev *pdev)
 {
 	u8 pcicfg;
 	pci_read_config_byte(pdev, 0x60, &pcicfg);
 	if ((pcicfg & 0x40) == 0)
 		pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
 	return ata_pci_device_resume(pdev);
 }

 /**
  *	cs5520_pci_device_suspend	-	device suspend
  *	@pdev: PCI device
  *
  *	We have to cut and waste bits from the standard method because
  *	the 5520 is a bit odd and not just a pure ATA device. As a result
  *	we must not disable it. The needed code is short and this avoids
  *	chip specific mess in the core code.
  */

 static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
 {
 	struct ata_host *host = dev_get_drvdata(&pdev->dev);
 	int rc = 0;

 	rc = ata_host_suspend(host, mesg);
 	if (rc)
 		return rc;

 	pci_save_state(pdev);
 	return 0;
 }
 #endif /* CONFIG_PM */

 /* For now keep DMA off. We can set it for all but A rev CS5510 once the
    core ATA code can handle it */

 static const struct pci_device_id pata_cs5520[] = {
 	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
 	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },

 	{ },
 };

 static struct pci_driver cs5520_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= pata_cs5520,
 	.probe 		= cs5520_init_one,
 	.remove		= cs5520_remove_one,
 #ifdef CONFIG_PM
 	.suspend	= cs5520_pci_device_suspend,
 	.resume		= cs5520_reinit_one,
 #endif
 };

 static int __init cs5520_init(void)
 {
 	return pci_register_driver(&cs5520_pci_driver);
 }

 static void __exit cs5520_exit(void)
 {
 	pci_unregister_driver(&cs5520_pci_driver);
 }

 MODULE_AUTHOR("Alan Cox");
 MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, pata_cs5520);
 MODULE_VERSION(DRV_VERSION);

 module_init(cs5520_init);
 module_exit(cs5520_exit);
	/*
	* IDE tuning and bus mastering support for the CS5510/CS5520
	* chipsets
	*
	* The CS5510/CS5520 are slightly unusual devices. Unlike the
	* typical IDE controllers they do bus mastering with the drive in
	* PIO mode and smarter silicon.
	*
	* The practical upshot of this is that we must always tune the
	* drive for the right PIO mode. We must also ignore all the blacklists
	* and the drive bus mastering DMA information. Also to confuse matters
	* further we can do DMA on PIO only drives.
	*
	* DMA on the 5510 also requires we disable_hlt() during DMA on early
	* revisions.
	*
	* * This driver is strictly experimental *
	*
	* (c) Copyright Red Hat Inc 2002
	*
	* This program is free software; you can redistribute it and/or modify it
	* under the terms of the GNU General Public License as published by the
	* Free Software Foundation; either version 2, or (at your option) any
	* later version.
	*
	* This program is distributed in the hope that it will be useful, but
	* WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
	* General Public License for more details.
	*
	* Documentation:
	* Not publically available.
	*/
	#include <linux/kernel.h>
	#include <linux/module.h>
	#include <linux/pci.h>
	#include <linux/init.h>
	#include <linux/blkdev.h>
	#include <linux/delay.h>
	#include <scsi/scsi_host.h>
	#include <linux/libata.h>

	#define DRV_NAME "pata_cs5520"
	#define DRV_VERSION "0.6.5"

	struct pio_clocks
	{
	int address;
	int assert;
	int recovery;
	};

	static const struct pio_clocks cs5520_pio_clocks[]={
	{3, 6, 11},
	{2, 5, 6},
	{1, 4, 3},
	{1, 3, 2},
	{1, 2, 1}
	};

	/**
	* cs5520_set_timings - program PIO timings
	* @ap: ATA port
	* @adev: ATA device
	*
	* Program the PIO mode timings for the controller according to the pio
	* clocking table.
	*/

	static void cs5520_set_timings(struct ata_port ap, struct ata_device adev, int pio)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int slave = adev->devno;

	pio -= XFER_PIO_0;

	/* Channel command timing */
	pci_write_config_byte(pdev, 0x62 + ap->port_no,
	(cs5520_pio_clocks[pio].recovery << 4) \|
	(cs5520_pio_clocks[pio].assert));
	/* FIXME: should these use address ? */
	/* Read command timing */
	pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
	(cs5520_pio_clocks[pio].recovery << 4) \|
	(cs5520_pio_clocks[pio].assert));
	/* Write command timing */
	pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
	(cs5520_pio_clocks[pio].recovery << 4) \|
	(cs5520_pio_clocks[pio].assert));
	}

	/**
	* cs5520_enable_dma - turn on DMA bits
	*
	* Turn on the DMA bits for this disk. Needed because the BIOS probably
	* has not done the work for us. Belongs in the core SATA code.
	*/

	static void cs5520_enable_dma(struct ata_port ap, struct ata_device adev)
	{
	/* Set the DMA enable/disable flag */
	u8 reg = ioread8(ap->ioaddr.bmdma_addr + 0x02);
	reg \|= 1<<(adev->devno + 5);
	iowrite8(reg, ap->ioaddr.bmdma_addr + 0x02);
	}

	/**
	* cs5520_set_dmamode - program DMA timings
	* @ap: ATA port
	* @adev: ATA device
	*
	* Program the DMA mode timings for the controller according to the pio
	* clocking table. Note that this device sets the DMA timings to PIO
	* mode values. This may seem bizarre but the 5520 architecture talks
	* PIO mode to the disk and DMA mode to the controller so the underlying
	* transfers are PIO timed.
	*/

	static void cs5520_set_dmamode(struct ata_port ap, struct ata_device adev)
	{
	static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 };
	cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]);
	cs5520_enable_dma(ap, adev);
	}

	/**
	* cs5520_set_piomode - program PIO timings
	* @ap: ATA port
	* @adev: ATA device
	*
	* Program the PIO mode timings for the controller according to the pio
	* clocking table. We know pio_mode will equal dma_mode because of the
	* CS5520 architecture. At least once we turned DMA on and wrote a
	* mode setter.
	*/

	static void cs5520_set_piomode(struct ata_port ap, struct ata_device adev)
	{
	cs5520_set_timings(ap, adev, adev->pio_mode);
	}

	static struct scsi_host_template cs5520_sht = {
	.module = THIS_MODULE,
	.name = DRV_NAME,
	.ioctl = ata_scsi_ioctl,
	.queuecommand = ata_scsi_queuecmd,
	.can_queue = ATA_DEF_QUEUE,
	.this_id = ATA_SHT_THIS_ID,
	.sg_tablesize = LIBATA_DUMB_MAX_PRD,
	.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
	.emulated = ATA_SHT_EMULATED,
	.use_clustering = ATA_SHT_USE_CLUSTERING,
	.proc_name = DRV_NAME,
	.dma_boundary = ATA_DMA_BOUNDARY,
	.slave_configure = ata_scsi_slave_config,
	.slave_destroy = ata_scsi_slave_destroy,
	.bios_param = ata_std_bios_param,
	};

	static struct ata_port_operations cs5520_port_ops = {
	.port_disable = ata_port_disable,
	.set_piomode = cs5520_set_piomode,
	.set_dmamode = cs5520_set_dmamode,

	.tf_load = ata_tf_load,
	.tf_read = ata_tf_read,
	.check_status = ata_check_status,
	.exec_command = ata_exec_command,
	.dev_select = ata_std_dev_select,

	.freeze = ata_bmdma_freeze,
	.thaw = ata_bmdma_thaw,
	.error_handler = ata_bmdma_error_handler,
	.post_internal_cmd = ata_bmdma_post_internal_cmd,
	.cable_detect = ata_cable_40wire,

	.bmdma_setup = ata_bmdma_setup,
	.bmdma_start = ata_bmdma_start,
	.bmdma_stop = ata_bmdma_stop,
	.bmdma_status = ata_bmdma_status,
	.qc_prep = ata_dumb_qc_prep,
	.qc_issue = ata_qc_issue_prot,
	.data_xfer = ata_data_xfer,

	.irq_clear = ata_bmdma_irq_clear,
	.irq_on = ata_irq_on,
	.irq_ack = ata_irq_ack,

	.port_start = ata_port_start,
	};

	static int __devinit cs5520_init_one(struct pci_dev pdev, const struct pci_device_id id)
	{
	struct ata_port_info pi = {
	.flags = ATA_FLAG_SLAVE_POSS,
	.pio_mask = 0x1f,
	.port_ops = &cs5520_port_ops,
	};
	const struct ata_port_info *ppi[2];
	u8 pcicfg;
	void *iomap[5];
	struct ata_host *host;
	struct ata_ioports *ioaddr;
	int i, rc;

	/* IDE port enable bits */
	pci_read_config_byte(pdev, 0x60, &pcicfg);

	/* Check if the ATA ports are enabled */
	if ((pcicfg & 3) == 0)
	return -ENODEV;

	ppi[0] = ppi[1] = &ata_dummy_port_info;
	if (pcicfg & 1)
	ppi[0] = π
	if (pcicfg & 2)
	ppi[1] = π

	if ((pcicfg & 0x40) == 0) {
	dev_printk(KERN_WARNING, &pdev->dev,
	"DMA mode disabled. Enabling.\n");
	pci_write_config_byte(pdev, 0x60, pcicfg \| 0x40);
	}

	pi.mwdma_mask = id->driver_data;

	host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
	if (!host)
	return -ENOMEM;

	/* Perform set up for DMA */
	if (pci_enable_device_bars(pdev, 1<<2)) {
	printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
	return -ENODEV;
	}

	if (pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
	printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
	return -ENODEV;
	}
	if (pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK)) {
	printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
	return -ENODEV;
	}

	/* Map IO ports and initialize host accordingly */
	iomap[0] = devm_ioport_map(&pdev->dev, 0x1F0, 8);
	iomap[1] = devm_ioport_map(&pdev->dev, 0x3F6, 1);
	iomap[2] = devm_ioport_map(&pdev->dev, 0x170, 8);
	iomap[3] = devm_ioport_map(&pdev->dev, 0x376, 1);
	iomap[4] = pcim_iomap(pdev, 2, 0);

	if (!iomap[0] \|\| !iomap[1] \|\| !iomap[2] \|\| !iomap[3] \|\| !iomap[4])
	return -ENOMEM;

	ioaddr = &host->ports[0]->ioaddr;
	ioaddr->cmd_addr = iomap[0];
	ioaddr->ctl_addr = iomap[1];
	ioaddr->altstatus_addr = iomap[1];
	ioaddr->bmdma_addr = iomap[4];
	ata_std_ports(ioaddr);

	ioaddr = &host->ports[1]->ioaddr;
	ioaddr->cmd_addr = iomap[2];
	ioaddr->ctl_addr = iomap[3];
	ioaddr->altstatus_addr = iomap[3];
	ioaddr->bmdma_addr = iomap[4] + 8;
	ata_std_ports(ioaddr);

	/* activate the host */
	pci_set_master(pdev);
	rc = ata_host_start(host);
	if (rc)
	return rc;

	for (i = 0; i < 2; i++) {
	static const int irq[] = { 14, 15 };
	struct ata_port *ap = host->ports[0];

	if (ata_port_is_dummy(ap))
	continue;

	rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
	ata_interrupt, 0, DRV_NAME, host);
	if (rc)
	return rc;

	if (i == 0)
	host->irq = irq[0];
	else
	host->irq2 = irq[1];
	}

	return ata_host_register(host, &cs5520_sht);
	}

	/**
	* cs5520_remove_one - device unload
	* @pdev: PCI device being removed
	*
	* Handle an unplug/unload event for a PCI device. Unload the
	* PCI driver but do not use the default handler as we manage
	* resources ourself and MUST NOT disable the device as it has
	* other functions.
	*/

	static void __devexit cs5520_remove_one(struct pci_dev *pdev)
	{
	struct device *dev = pci_dev_to_dev(pdev);
	struct ata_host *host = dev_get_drvdata(dev);

	ata_host_detach(host);
	}

	#ifdef CONFIG_PM
	/**
	* cs5520_reinit_one - device resume
	* @pdev: PCI device
	*
	* Do any reconfiguration work needed by a resume from RAM. We need
	* to restore DMA mode support on BIOSen which disabled it
	*/

	static int cs5520_reinit_one(struct pci_dev *pdev)
	{
	u8 pcicfg;
	pci_read_config_byte(pdev, 0x60, &pcicfg);
	if ((pcicfg & 0x40) == 0)
	pci_write_config_byte(pdev, 0x60, pcicfg \| 0x40);
	return ata_pci_device_resume(pdev);
	}

	/**
	* cs5520_pci_device_suspend - device suspend
	* @pdev: PCI device
	*
	* We have to cut and waste bits from the standard method because
	* the 5520 is a bit odd and not just a pure ATA device. As a result
	* we must not disable it. The needed code is short and this avoids
	* chip specific mess in the core code.
	*/

	static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
	{
	struct ata_host *host = dev_get_drvdata(&pdev->dev);
	int rc = 0;

	rc = ata_host_suspend(host, mesg);
	if (rc)
	return rc;

	pci_save_state(pdev);
	return 0;
	}
	#endif /* CONFIG_PM */

	/* For now keep DMA off. We can set it for all but A rev CS5510 once the
	core ATA code can handle it */

	static const struct pci_device_id pata_cs5520[] = {
	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },

	{ },
	};

	static struct pci_driver cs5520_pci_driver = {
	.name = DRV_NAME,
	.id_table = pata_cs5520,
	.probe = cs5520_init_one,
	.remove = cs5520_remove_one,
	#ifdef CONFIG_PM
	.suspend = cs5520_pci_device_suspend,
	.resume = cs5520_reinit_one,
	#endif
	};

	static int __init cs5520_init(void)
	{
	return pci_register_driver(&cs5520_pci_driver);
	}

	static void __exit cs5520_exit(void)
	{
	pci_unregister_driver(&cs5520_pci_driver);
	}

	MODULE_AUTHOR("Alan Cox");
	MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
	MODULE_LICENSE("GPL");
	MODULE_DEVICE_TABLE(pci, pata_cs5520);
	MODULE_VERSION(DRV_VERSION);

	module_init(cs5520_init);
	module_exit(cs5520_exit);