ath6kl: Initialize target wlan values for every vif
Wlan parameters need to be configured for every vif
in target.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diff --git a/drivers/net/wireless/ath/ath6kl/init.c b/drivers/net/wireless/ath/ath6kl/init.c
index 7784b2c..1dad985 100644
--- a/drivers/net/wireless/ath/ath6kl/init.c
+++ b/drivers/net/wireless/ath/ath6kl/init.c
@@ -352,7 +352,7 @@
}
-static int ath6kl_target_config_wlan_params(struct ath6kl *ar)
+static int ath6kl_target_config_wlan_params(struct ath6kl *ar, int idx)
{
int status = 0;
int ret;
@@ -362,46 +362,50 @@
* default values. Required if checksum offload is needed. Set
* RxMetaVersion to 2.
*/
- if (ath6kl_wmi_set_rx_frame_format_cmd(ar->wmi,
+ if (ath6kl_wmi_set_rx_frame_format_cmd(ar->wmi, idx,
ar->rx_meta_ver, 0, 0)) {
ath6kl_err("unable to set the rx frame format\n");
status = -EIO;
}
if (ar->conf_flags & ATH6KL_CONF_IGNORE_PS_FAIL_EVT_IN_SCAN)
- if ((ath6kl_wmi_pmparams_cmd(ar->wmi, 0, 1, 0, 0, 1,
+ if ((ath6kl_wmi_pmparams_cmd(ar->wmi, idx, 0, 1, 0, 0, 1,
IGNORE_POWER_SAVE_FAIL_EVENT_DURING_SCAN)) != 0) {
ath6kl_err("unable to set power save fail event policy\n");
status = -EIO;
}
if (!(ar->conf_flags & ATH6KL_CONF_IGNORE_ERP_BARKER))
- if ((ath6kl_wmi_set_lpreamble_cmd(ar->wmi, 0,
+ if ((ath6kl_wmi_set_lpreamble_cmd(ar->wmi, idx, 0,
WMI_DONOT_IGNORE_BARKER_IN_ERP)) != 0) {
ath6kl_err("unable to set barker preamble policy\n");
status = -EIO;
}
- if (ath6kl_wmi_set_keepalive_cmd(ar->wmi,
+ if (ath6kl_wmi_set_keepalive_cmd(ar->wmi, idx,
WLAN_CONFIG_KEEP_ALIVE_INTERVAL)) {
ath6kl_err("unable to set keep alive interval\n");
status = -EIO;
}
- if (ath6kl_wmi_disctimeout_cmd(ar->wmi,
+ if (ath6kl_wmi_disctimeout_cmd(ar->wmi, idx,
WLAN_CONFIG_DISCONNECT_TIMEOUT)) {
ath6kl_err("unable to set disconnect timeout\n");
status = -EIO;
}
if (!(ar->conf_flags & ATH6KL_CONF_ENABLE_TX_BURST))
- if (ath6kl_wmi_set_wmm_txop(ar->wmi, WMI_TXOP_DISABLED)) {
+ if (ath6kl_wmi_set_wmm_txop(ar->wmi, idx, WMI_TXOP_DISABLED)) {
ath6kl_err("unable to set txop bursting\n");
status = -EIO;
}
+ /*
+ * FIXME: Make sure p2p configurations are not applied to
+ * non-p2p capable interfaces when multivif support is enabled.
+ */
if (ar->p2p) {
- ret = ath6kl_wmi_info_req_cmd(ar->wmi,
+ ret = ath6kl_wmi_info_req_cmd(ar->wmi, idx,
P2P_FLAG_CAPABILITIES_REQ |
P2P_FLAG_MACADDR_REQ |
P2P_FLAG_HMODEL_REQ);
@@ -413,9 +417,13 @@
}
}
+ /*
+ * FIXME: Make sure p2p configurations are not applied to
+ * non-p2p capable interfaces when multivif support is enabled.
+ */
if (ar->p2p) {
/* Enable Probe Request reporting for P2P */
- ret = ath6kl_wmi_probe_report_req_cmd(ar->wmi, true);
+ ret = ath6kl_wmi_probe_report_req_cmd(ar->wmi, idx, true);
if (ret) {
ath6kl_dbg(ATH6KL_DBG_TRC, "failed to enable Probe "
"Request reporting (%d)\n", ret);
@@ -1543,9 +1551,11 @@
ar->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM |
WIPHY_FLAG_HAVE_AP_SME;
- status = ath6kl_target_config_wlan_params(ar);
- if (status)
- goto err_htc_stop;
+ for (i = 0; i < MAX_NUM_VIF; i++) {
+ status = ath6kl_target_config_wlan_params(ar, i);
+ if (status)
+ goto err_htc_stop;
+ }
/*
* Set mac address which is received in ready event