mac80211: adding 802.11n HT framework definitions
New structures:
- ieee80211_ht_info: describing STA's HT capabilities
- ieee80211_ht_bss_info: describing BSS's HT characteristics
Changed structures:
- ieee80211_hw_mode: now also holds PHY HT capabilities for each HW mode
- ieee80211_conf: ht_conf holds current self HT configuration
ht_bss_conf holds current BSS HT configuration
- flag IEEE80211_CONF_SUPPORT_HT_MODE added to indicate if HT use is
desired
- sta_info: now also holds Peer's HT capabilities
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 4cc5b1c..79e9645 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -139,17 +139,54 @@
};
/**
+ * struct ieee80211_ht_info - describing STA's HT capabilities
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT capabilities for an STA.
+ *
+ * @ht_supported: is HT supported by STA, 0: no, 1: yes
+ * @cap: HT capabilities map as described in 802.11n spec
+ * @ampdu_factor: Maximum A-MPDU length factor
+ * @ampdu_density: Minimum A-MPDU spacing
+ * @supp_mcs_set: Supported MCS set as described in 802.11n spec
+ */
+struct ieee80211_ht_info {
+ u8 ht_supported;
+ u16 cap; /* use IEEE80211_HT_CAP_ */
+ u8 ampdu_factor;
+ u8 ampdu_density;
+ u8 supp_mcs_set[16];
+};
+
+/**
+ * struct ieee80211_ht_bss_info - describing BSS's HT characteristics
+ *
+ * This structure describes most essential parameters needed
+ * to describe 802.11n HT characteristics in a BSS
+ *
+ * @primary_channel: channel number of primery channel
+ * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
+ * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection)
+ */
+struct ieee80211_ht_bss_info {
+ u8 primary_channel;
+ u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */
+ u8 bss_op_mode; /* use IEEE80211_HT_IE_ */
+};
+
+/**
* struct ieee80211_hw_mode - PHY mode definition
*
* This structure describes the capabilities supported by the device
* in a single PHY mode.
*
+ * @list: internal
+ * @channels: pointer to array of supported channels
+ * @rates: pointer to array of supported bitrates
* @mode: the PHY mode for this definition
* @num_channels: number of supported channels
- * @channels: pointer to array of supported channels
* @num_rates: number of supported bitrates
- * @rates: pointer to array of supported bitrates
- * @list: internal
+ * @ht_info: PHY's 802.11n HT abilities for this mode
*/
struct ieee80211_hw_mode {
struct list_head list;
@@ -158,6 +195,7 @@
enum ieee80211_phymode mode;
int num_channels;
int num_rates;
+ struct ieee80211_ht_info ht_info;
};
/**
@@ -406,11 +444,12 @@
*
* @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time
* @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
- *
+ * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported)
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_SHORT_SLOT_TIME = 1<<0,
- IEEE80211_CONF_RADIOTAP = 1<<1,
+ IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0),
+ IEEE80211_CONF_RADIOTAP = (1<<1),
+ IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2),
};
/**
@@ -434,6 +473,8 @@
* @antenna_sel_tx: transmit antenna selection, 0: default/diversity,
* 1/2: antenna 0/1
* @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx
+ * @ht_conf: describes current self configuration of 802.11n HT capabilies
+ * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters
*/
struct ieee80211_conf {
int channel; /* IEEE 802.11 channel number */
@@ -452,6 +493,9 @@
u8 antenna_max;
u8 antenna_sel_tx;
u8 antenna_sel_rx;
+
+ struct ieee80211_ht_info ht_conf;
+ struct ieee80211_ht_bss_info ht_bss_conf;
};
/**