trivial: fix typo milisecond/millisecond for documentation and source comments.
Signed-off-by: Martin Olsson <martin@minimum.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
diff --git a/Documentation/CodingStyle b/Documentation/CodingStyle
index 72968cd..8bb3723 100644
--- a/Documentation/CodingStyle
+++ b/Documentation/CodingStyle
@@ -698,8 +698,8 @@
kernel, which in turn slows the system as a whole down, due to a bigger
icache footprint for the CPU and simply because there is less memory
available for the pagecache. Just think about it; a pagecache miss causes a
-disk seek, which easily takes 5 miliseconds. There are a LOT of cpu cycles
-that can go into these 5 miliseconds.
+disk seek, which easily takes 5 milliseconds. There are a LOT of cpu cycles
+that can go into these 5 milliseconds.
A reasonable rule of thumb is to not put inline at functions that have more
than 3 lines of code in them. An exception to this rule are the cases where
diff --git a/drivers/ide/ide-atapi.c b/drivers/ide/ide-atapi.c
index 757e595..ae1cae3 100644
--- a/drivers/ide/ide-atapi.c
+++ b/drivers/ide/ide-atapi.c
@@ -577,7 +577,7 @@
/*
* If necessary schedule the packet transfer to occur 'timeout'
- * miliseconds later in ide_delayed_transfer_pc() after the
+ * milliseconds later in ide_delayed_transfer_pc() after the
* device says it's ready for a packet.
*/
if (drive->atapi_flags & IDE_AFLAG_ZIP_DRIVE) {
diff --git a/drivers/isdn/mISDN/dsp_core.c b/drivers/isdn/mISDN/dsp_core.c
index 3083338..47dbfe2 100644
--- a/drivers/isdn/mISDN/dsp_core.c
+++ b/drivers/isdn/mISDN/dsp_core.c
@@ -502,7 +502,7 @@
break;
}
dsp->cmx_delay = (*((int *)data)) << 3;
- /* miliseconds to samples */
+ /* milliseconds to samples */
if (dsp->cmx_delay >= (CMX_BUFF_HALF>>1))
/* clip to half of maximum usable buffer
(half of half buffer) */
diff --git a/drivers/net/ipg.h b/drivers/net/ipg.h
index dd9318f..dfc2541 100644
--- a/drivers/net/ipg.h
+++ b/drivers/net/ipg.h
@@ -514,7 +514,7 @@
#define IPG_DMALIST_ALIGN_PAD 0x07
#define IPG_MULTICAST_HASHTABLE_SIZE 0x40
-/* Number of miliseconds to wait after issuing a software reset.
+/* Number of milliseconds to wait after issuing a software reset.
* 0x05 <= IPG_AC_RESETWAIT to account for proper 10Mbps operation.
*/
#define IPG_AC_RESETWAIT 0x05
diff --git a/drivers/s390/scsi/zfcp_fc.c b/drivers/s390/scsi/zfcp_fc.c
index 19ae084..18fd975 100644
--- a/drivers/s390/scsi/zfcp_fc.c
+++ b/drivers/s390/scsi/zfcp_fc.c
@@ -116,7 +116,7 @@
{
if (atomic_dec_return(&wka_port->refcount) != 0)
return;
- /* wait 10 miliseconds, other reqs might pop in */
+ /* wait 10 milliseconds, other reqs might pop in */
schedule_delayed_work(&wka_port->work, HZ / 100);
}
diff --git a/drivers/scsi/dpt/osd_util.h b/drivers/scsi/dpt/osd_util.h
index 4b56c04..b2613c2 100644
--- a/drivers/scsi/dpt/osd_util.h
+++ b/drivers/scsi/dpt/osd_util.h
@@ -342,7 +342,7 @@
/* wakes up the specifed thread */
void osdWakeThread(uLONG);
-/* osd sleep for x miliseconds */
+/* osd sleep for x milliseconds */
void osdSleep(uLONG);
#define DPT_THREAD_PRIORITY_LOWEST 0x00
diff --git a/drivers/usb/serial/io_ti.c b/drivers/usb/serial/io_ti.c
index eabf20e..db964db 100644
--- a/drivers/usb/serial/io_ti.c
+++ b/drivers/usb/serial/io_ti.c
@@ -102,7 +102,7 @@
__u8 shadow_mcr;
__u8 shadow_lsr;
__u8 lsr_mask;
- __u32 ump_read_timeout; /* Number of miliseconds the UMP will
+ __u32 ump_read_timeout; /* Number of milliseconds the UMP will
wait without data before completing
a read short */
int baud_rate;
diff --git a/sound/pci/vx222/vx222_ops.c b/sound/pci/vx222/vx222_ops.c
index c0efe44..6416d3f 100644
--- a/sound/pci/vx222/vx222_ops.c
+++ b/sound/pci/vx222/vx222_ops.c
@@ -367,7 +367,7 @@
unsigned int port;
const unsigned char *image;
- /* XILINX reset (wait at least 1 milisecond between reset on and off). */
+ /* XILINX reset (wait at least 1 millisecond between reset on and off). */
vx_outl(chip, CNTRL, VX_CNTRL_REGISTER_VALUE | VX_XILINX_RESET_MASK);
vx_inl(chip, CNTRL);
msleep(10);