wl1271: Add proper WLAN-BT co-ex configuration, and enable co-ex.
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c
index b3abb45..6501d6e 100644
--- a/drivers/net/wireless/wl12xx/wl1271_main.c
+++ b/drivers/net/wireless/wl12xx/wl1271_main.c
@@ -48,17 +48,57 @@
static struct conf_drv_settings default_conf = {
.sg = {
- .per_threshold = 7500,
- .max_scan_compensation_time = 120000,
- .nfs_sample_interval = 400,
- .load_ratio = 50,
- .auto_ps_mode = 0,
- .probe_req_compensation = 170,
- .scan_window_compensation = 50,
- .antenna_config = 0,
- .beacon_miss_threshold = 60,
- .rate_adaptation_threshold = CONF_HW_BIT_RATE_12MBPS,
- .rate_adaptation_snr = 0
+ .params = {
+ [CONF_SG_BT_PER_THRESHOLD] = 7500,
+ [CONF_SG_HV3_MAX_OVERRIDE] = 0,
+ [CONF_SG_BT_NFS_SAMPLE_INTERVAL] = 400,
+ [CONF_SG_BT_LOAD_RATIO] = 50,
+ [CONF_SG_AUTO_PS_MODE] = 0,
+ [CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
+ [CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
+ [CONF_SG_ANTENNA_CONFIGURATION] = 0,
+ [CONF_SG_BEACON_MISS_PERCENT] = 60,
+ [CONF_SG_RATE_ADAPT_THRESH] = 12,
+ [CONF_SG_RATE_ADAPT_SNR] = 0,
+ [CONF_SG_WLAN_PS_BT_ACL_MASTER_MIN_BR] = 10,
+ [CONF_SG_WLAN_PS_BT_ACL_MASTER_MAX_BR] = 30,
+ [CONF_SG_WLAN_PS_MAX_BT_ACL_MASTER_BR] = 8,
+ [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MIN_BR] = 20,
+ [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MAX_BR] = 50,
+ /* Note: with UPSD, this should be 4 */
+ [CONF_SG_WLAN_PS_MAX_BT_ACL_SLAVE_BR] = 8,
+ [CONF_SG_WLAN_PS_BT_ACL_MASTER_MIN_EDR] = 7,
+ [CONF_SG_WLAN_PS_BT_ACL_MASTER_MAX_EDR] = 25,
+ [CONF_SG_WLAN_PS_MAX_BT_ACL_MASTER_EDR] = 20,
+ /* Note: with UPDS, this should be 15 */
+ [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MIN_EDR] = 8,
+ /* Note: with UPDS, this should be 50 */
+ [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MAX_EDR] = 40,
+ /* Note: with UPDS, this should be 10 */
+ [CONF_SG_WLAN_PS_MAX_BT_ACL_SLAVE_EDR] = 20,
+ [CONF_SG_RXT] = 1200,
+ [CONF_SG_TXT] = 1000,
+ [CONF_SG_ADAPTIVE_RXT_TXT] = 1,
+ [CONF_SG_PS_POLL_TIMEOUT] = 10,
+ [CONF_SG_UPSD_TIMEOUT] = 10,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_MASTER_MIN_EDR] = 7,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_MASTER_MAX_EDR] = 15,
+ [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_MASTER_EDR] = 15,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_SLAVE_MIN_EDR] = 8,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_SLAVE_MAX_EDR] = 20,
+ [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_SLAVE_EDR] = 15,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_MIN_BR] = 20,
+ [CONF_SG_WLAN_ACTIVE_BT_ACL_MAX_BR] = 50,
+ [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_BR] = 10,
+ [CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200,
+ [CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP] = 800,
+ [CONF_SG_PASSIVE_SCAN_A2DP_BT_TIME] = 75,
+ [CONF_SG_PASSIVE_SCAN_A2DP_WLAN_TIME] = 15,
+ [CONF_SG_HV3_MAX_SERVED] = 6,
+ [CONF_SG_DHCP_TIME] = 5000,
+ [CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100,
+ },
+ .state = CONF_SG_PROTECTIVE,
},
.rx = {
.rx_msdu_life_time = 512000,