Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/Documentation/isdn/README.HiSax b/Documentation/isdn/README.HiSax
new file mode 100644
index 0000000..031c8d8
--- /dev/null
+++ b/Documentation/isdn/README.HiSax
@@ -0,0 +1,659 @@
+HiSax is a Linux hardware-level driver for passive ISDN cards with Siemens
+chipset (ISAC_S 2085/2086/2186, HSCX SAB 82525). It is based on the Teles
+driver from Jan den Ouden.
+It is meant to be used with isdn4linux, an ISDN link-level module for Linux
+written by Fritz Elfert.
+
+ This program is free software; you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation; either version 2 of the License, or
+ (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program; if not, write to the Free Software
+ Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+
+
+Supported cards
+---------------
+
+Teles 8.0/16.0/16.3 and compatible ones
+Teles 16.3c
+Teles S0/PCMCIA
+Teles PCI
+Teles S0Box
+Creatix S0Box
+Creatix PnP S0
+Compaq ISDN S0 ISA card
+AVM A1 (Fritz, Teledat 150)
+AVM Fritz PCMCIA
+AVM Fritz PnP
+AVM Fritz PCI
+ELSA Microlink PCC-16, PCF, PCF-Pro, PCC-8
+ELSA Quickstep 1000
+ELSA Quickstep 1000PCI
+ELSA Quickstep 3000 (same settings as QS1000)
+ELSA Quickstep 3000PCI
+ELSA PCMCIA
+ITK ix1-micro Rev.2
+Eicon Diva 2.0 ISA and PCI (S0 and U interface, no PRO version)
+Eicon Diva 2.01 ISA and PCI
+Eicon Diva 2.02 PCI
+Eicon Diva Piccola
+ASUSCOM NETWORK INC. ISDNLink 128K PC adapter (order code I-IN100-ST-D)
+Dynalink IS64PH (OEM version of ASUSCOM NETWORK INC. ISDNLink 128K adapter)
+PCBIT-DP (OEM version of ASUSCOM NETWORK INC. ISDNLink)
+HFC-2BS0 based cards (TeleInt SA1)
+Sedlbauer Speed Card (Speed Win, Teledat 100, PCI, Fax+)
+Sedlbauer Speed Star/Speed Star2 (PCMCIA)
+Sedlbauer ISDN-Controller PC/104
+USR Sportster internal TA (compatible Stollmann tina-pp V3)
+USR internal TA PCI
+ith Kommunikationstechnik GmbH MIC 16 ISA card
+Traverse Technologie NETjet PCI S0 card and NETspider U card
+Ovislink ISDN sc100-p card (NETjet driver)
+Dr. Neuhaus Niccy PnP/PCI
+Siemens I-Surf 1.0
+Siemens I-Surf 2.0 (with IPAC, try type 12 asuscom)
+ACER P10
+HST Saphir
+Berkom Telekom A4T
+Scitel Quadro
+Gazel ISDN cards
+HFC-PCI based cards
+Winbond W6692 based cards
+HFC-S+, HFC-SP/PCMCIA cards
+formula-n enternow
+Gerdes Power ISDN
+
+Note: PCF, PCF-Pro: up to now, only the ISDN part is supported
+ PCC-8: not tested yet
+ Eicon.Diehl Diva U interface not tested
+
+If you know other passive cards with the Siemens chipset, please let me know.
+You can combine any card, if there is no conflict between the resources
+(io, mem, irq).
+
+
+Configuring the driver
+----------------------
+
+The HiSax driver can either be built directly into the kernel or as a module.
+It can be configured using the command line feature while loading the kernel
+with LILO or LOADLIN or, if built as a module, using insmod/modprobe with
+parameters.
+There is also some config needed before you compile the kernel and/or
+modules. It is included in the normal "make [menu]config" target at the
+kernel. Don't forget it, especially to select the right D-channel protocol.
+
+Please note: In older versions of the HiSax driver, all PnP cards
+needed to be configured with isapnp and worked only with the HiSax
+driver used as a module.
+
+In the current version, HiSax will automatically use the in-kernel
+ISAPnP support, provided you selected it during kernel configuration
+(CONFIG_ISAPNP), if you don't give the io=, irq= command line parameters.
+
+The affected card types are: 4,7,12,14,19,27-30
+
+a) when built as a module
+-------------------------
+
+insmod/modprobe hisax.o \
+ io=iobase irq=IRQ mem=membase type=card_type \
+ protocol=D_channel_protocol id=idstring
+
+or, if several cards are installed:
+
+insmod/modprobe hisax.o \
+ io=iobase1,iobase2,... irq=IRQ1,IRQ2,... mem=membase1,membase2,... \
+ type=card_type1,card_type2,... \
+ protocol=D_channel_protocol1,D_channel_protocol2,... \
+ id=idstring1%idstring2 ...
+
+where "iobaseN" represents the I/O base address of the Nth card, "membaseN"
+the memory base address of the Nth card, etc.
+
+The reason for the delimiter "%" being used in the idstrings is that ","
+won't work with the current modules package.
+
+The parameters may be specified in any order. For example, the "io"
+parameter may precede the "irq" parameter, or vice versa. If several
+cards are installed, the ordering within the comma separated parameter
+lists must of course be consistent.
+
+Only parameters applicable to the card type need to be specified. For
+example, the Teles 16.3 card is not memory-mapped, so the "mem"
+parameter may be omitted for this card. Sometimes it may be necessary
+to specify a dummy parameter, however. This is the case when there is
+a card of a different type later in the list that needs a parameter
+which the preceding card does not. For instance, if a Teles 16.0 card
+is listed after a Teles 16.3 card, a dummy memory base parameter of 0
+must be specified for the 16.3. Instead of a dummy value, the parameter
+can also be skipped by simply omitting the value. For example:
+mem=,0xd0000. See example 6 below.
+
+The parameter for the D-Channel protocol may be omitted if you selected the
+correct one during kernel config. Valid values are "1" for German 1TR6,
+"2" for EDSS1 (Euro ISDN), "3" for leased lines (no D-Channel) and "4"
+for US NI1.
+With US NI1 you have to include your SPID into the MSN setting in the form
+<MSN>:<SPID> for example (your phonenumber is 1234 your SPID 5678):
+AT&E1234:5678 on ttyI interfaces
+isdnctrl eaz ippp0 1234:5678 on network devices
+
+The Creatix/Teles PnP cards use io1= and io2= instead of io= for specifying
+the I/O addresses of the ISAC and HSCX chips, respectively.
+
+Card types:
+
+ Type Required parameters (in addition to type and protocol)
+
+ 1 Teles 16.0 irq, mem, io
+ 2 Teles 8.0 irq, mem
+ 3 Teles 16.3 (non PnP) irq, io
+ 4 Creatix/Teles PnP irq, io0 (ISAC), io1 (HSCX)
+ 5 AVM A1 (Fritz) irq, io
+ 6 ELSA PCC/PCF cards io or nothing for autodetect (the iobase is
+ required only if you have more than one ELSA
+ card in your PC)
+ 7 ELSA Quickstep 1000 irq, io (from isapnp setup)
+ 8 Teles 16.3 PCMCIA irq, io
+ 9 ITK ix1-micro Rev.2 irq, io
+ 10 ELSA PCMCIA irq, io (set with card manager)
+ 11 Eicon.Diehl Diva ISA PnP irq, io
+ 11 Eicon.Diehl Diva PCI no parameter
+ 12 ASUS COM ISDNLink irq, io (from isapnp setup)
+ 13 HFC-2BS0 based cards irq, io
+ 14 Teles 16.3c PnP irq, io
+ 15 Sedlbauer Speed Card irq, io
+ 15 Sedlbauer PC/104 irq, io
+ 15 Sedlbauer Speed PCI no parameter
+ 16 USR Sportster internal irq, io
+ 17 MIC card irq, io
+ 18 ELSA Quickstep 1000PCI no parameter
+ 19 Compaq ISDN S0 ISA card irq, io0, io1, io (from isapnp setup io=IO2)
+ 20 NETjet PCI card no parameter
+ 21 Teles PCI no parameter
+ 22 Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)
+ 24 Dr. Neuhaus Niccy PnP irq, io0, io1 (from isapnp setup)
+ 24 Dr. Neuhaus Niccy PCI no parameter
+ 25 Teles S0Box irq, io (of the used lpt port)
+ 26 AVM A1 PCMCIA (Fritz!) irq, io (set with card manager)
+ 27 AVM PnP (Fritz!PnP) irq, io (from isapnp setup)
+ 27 AVM PCI (Fritz!PCI) no parameter
+ 28 Sedlbauer Speed Fax+ irq, io (from isapnp setup)
+ 29 Siemens I-Surf 1.0 irq, io, memory (from isapnp setup)
+ 30 ACER P10 irq, io (from isapnp setup)
+ 31 HST Saphir irq, io
+ 32 Telekom A4T none
+ 33 Scitel Quadro subcontroller (4*S0, subctrl 1...4)
+ 34 Gazel ISDN cards (ISA) irq,io
+ 34 Gazel ISDN cards (PCI) none
+ 35 HFC 2BDS0 PCI none
+ 36 W6692 based PCI cards none
+ 37 HFC 2BDS0 S+, SP irq,io
+ 38 NETspider U PCI card none
+ 39 HFC 2BDS0 SP/PCMCIA irq,io (set with cardmgr)
+ 40 hotplug interface
+ 41 Formula-n enter:now PCI none
+
+At the moment IRQ sharing is only possible with PCI cards. Please make sure
+that your IRQ is free and enabled for ISA use.
+
+
+Examples for module loading
+
+1. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 10
+ modprobe hisax type=3 protocol=2 io=0x280 irq=10
+
+2. Teles 16.0, 1TR6 ISDN, I/O base d80 hex, IRQ 5, Memory d0000 hex
+ modprobe hisax protocol=1 type=1 io=0xd80 mem=0xd0000 irq=5
+
+3. Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and ELSA PCF, Euro ISDN
+ modprobe hisax type=5,6 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa
+
+4. Any ELSA PCC/PCF card, Euro ISDN
+ modprobe hisax type=6 protocol=2
+
+5. Teles 16.3 PnP, Euro ISDN, with isapnp configured
+ isapnp config: (INT 0 (IRQ 10 (MODE +E)))
+ (IO 0 (BASE 0x0580))
+ (IO 1 (BASE 0x0180))
+ modprobe hisax type=4 protocol=2 irq=10 io0=0x580 io1=0x180
+
+ In the current version of HiSax, you can instead simply use
+
+ modprobe hisax type=4 protocol=2
+
+ if you configured your kernel for ISAPnP. Don't run isapnp in
+ this case!
+
+6. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 12 and
+ Teles 16.0, 1TR6, IRQ 5, Memory d0000 hex
+ modprobe hisax type=3,1 protocol=2,1 io=0x280 mem=0,0xd0000
+
+ Please note the dummy 0 memory address for the Teles 16.3, used as a
+ placeholder as described above, in the last example.
+
+7. Teles PCMCIA, Euro ISDN, I/O base 180 hex, IRQ 15 (default values)
+ modprobe hisax type=8 protocol=2 io=0x180 irq=15
+
+
+b) using LILO/LOADLIN, with the driver compiled directly into the kernel
+------------------------------------------------------------------------
+
+hisax=typ1,dp1,pa_1,pb_1,pc_1[,typ2,dp2,pa_2 ... \
+ typn,dpn,pa_n,pb_n,pc_n][,idstring1[,idstring2,...,idstringn]]
+
+where
+ typ1 = type of 1st card (default depends on kernel settings)
+ dp1 = D-Channel protocol of 1st card. 1=1TR6, 2=EDSS1, 3=leased
+ pa_1 = 1st parameter (depending on the type of the card)
+ pb_1 = 2nd parameter ( " " " " " " " )
+ pc_1 = 3rd parameter ( " " " " " " " )
+
+ typ2,dp2,pa_2,pb_2,pc_2 = Parameters of the second card (defaults: none)
+ typn,dpn,pa_n,pb_n,pc_n = Parameters of the n'th card (up to 16 cards are
+ supported)
+
+ idstring = Driver ID for accessing the particular card with utility
+ programs and for identification when using a line monitor
+ (default: "HiSax")
+
+ Note: the ID string must start with an alphabetical character!
+
+Card types:
+
+type
+ 1 Teles 16.0 pa=irq pb=membase pc=iobase
+ 2 Teles 8.0 pa=irq pb=membase
+ 3 Teles 16.3 pa=irq pb=iobase
+ 4 Creatix/Teles PNP ONLY WORKS AS A MODULE !
+ 5 AVM A1 (Fritz) pa=irq pb=iobase
+ 6 ELSA PCC/PCF cards pa=iobase or nothing for autodetect
+ 7 ELSA Quickstep 1000 ONLY WORKS AS A MODULE !
+ 8 Teles S0 PCMCIA pa=irq pb=iobase
+ 9 ITK ix1-micro Rev.2 pa=irq pb=iobase
+ 10 ELSA PCMCIA pa=irq, pb=io (set with card manager)
+ 11 Eicon.Diehl Diva ISAPnP ONLY WORKS AS A MODULE !
+ 11 Eicon.Diehl Diva PCI no parameter
+ 12 ASUS COM ISDNLink ONLY WORKS AS A MODULE !
+ 13 HFC-2BS0 based cards pa=irq pb=io
+ 14 Teles 16.3c PnP ONLY WORKS AS A MODULE !
+ 15 Sedlbauer Speed Card pa=irq pb=io (Speed Win only as module !)
+ 15 Sedlbauer PC/104 pa=irq pb=io
+ 15 Sedlbauer Speed PCI no parameter
+ 16 USR Sportster internal pa=irq pb=io
+ 17 MIC card pa=irq pb=io
+ 18 ELSA Quickstep 1000PCI no parameter
+ 19 Compaq ISDN S0 ISA card ONLY WORKS AS A MODULE !
+ 20 NETjet PCI card no parameter
+ 21 Teles PCI no parameter
+ 22 Sedlbauer Speed Star (PCMCIA) pa=irq, pb=io (set with card manager)
+ 24 Dr. Neuhaus Niccy PnP ONLY WORKS AS A MODULE !
+ 24 Dr. Neuhaus Niccy PCI no parameter
+ 25 Teles S0Box pa=irq, pb=io (of the used lpt port)
+ 26 AVM A1 PCMCIA (Fritz!) pa=irq, pb=io (set with card manager)
+ 27 AVM PnP (Fritz!PnP) ONLY WORKS AS A MODULE !
+ 27 AVM PCI (Fritz!PCI) no parameter
+ 28 Sedlbauer Speed Fax+ ONLY WORKS AS A MODULE !
+ 29 Siemens I-Surf 1.0 ONLY WORKS AS A MODULE !
+ 30 ACER P10 ONLY WORKS AS A MODULE !
+ 31 HST Saphir pa=irq, pb=io
+ 32 Telekom A4T no parameter
+ 33 Scitel Quadro subcontroller (4*S0, subctrl 1...4)
+ 34 Gazel ISDN cards (ISA) pa=irq, pb=io
+ 34 Gazel ISDN cards (PCI) no parameter
+ 35 HFC 2BDS0 PCI no parameter
+ 36 W6692 based PCI cards none
+ 37 HFC 2BDS0 S+,SP/PCMCIA ONLY WORKS AS A MODULE !
+ 38 NETspider U PCI card none
+ 39 HFC 2BDS0 SP/PCMCIA ONLY WORKS AS A MODULE !
+ 40 hotplug interface ONLY WORKS AS A MODULE !
+ 41 Formula-n enter:now PCI none
+
+Running the driver
+------------------
+
+When you insmod isdn.o and hisax.o (or with the in-kernel version, during
+boot time), a few lines should appear in your syslog. Look for something like:
+
+Apr 13 21:01:59 kke01 kernel: HiSax: Driver for Siemens chip set ISDN cards
+Apr 13 21:01:59 kke01 kernel: HiSax: Version 2.9
+Apr 13 21:01:59 kke01 kernel: HiSax: Revisions 1.14/1.9/1.10/1.25/1.8
+Apr 13 21:01:59 kke01 kernel: HiSax: Total 1 card defined
+Apr 13 21:01:59 kke01 kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax1 (0)
+Apr 13 21:01:59 kke01 kernel: HiSax: Elsa driver Rev. 1.13
+...
+Apr 13 21:01:59 kke01 kernel: Elsa: PCF-Pro found at 0x360 Rev.:C IRQ 10
+Apr 13 21:01:59 kke01 kernel: Elsa: timer OK; resetting card
+Apr 13 21:01:59 kke01 kernel: Elsa: HSCX version A: V2.1 B: V2.1
+Apr 13 21:01:59 kke01 kernel: Elsa: ISAC 2086/2186 V1.1
+...
+Apr 13 21:01:59 kke01 kernel: HiSax: DSS1 Rev. 1.14
+Apr 13 21:01:59 kke01 kernel: HiSax: 2 channels added
+
+This means that the card is ready for use.
+Cabling problems or line-downs are not detected, and only some ELSA cards can
+detect the S0 power.
+
+Remember that, according to the new strategy for accessing low-level drivers
+from within isdn4linux, you should also define a driver ID while doing
+insmod: Simply append hisax_id=<SomeString> to the insmod command line. This
+string MUST NOT start with a digit or a small 'x'!
+
+At this point you can run a 'cat /dev/isdnctrl0' and view debugging messages.
+
+At the moment, debugging messages are enabled with the hisaxctrl tool:
+
+ hisaxctrl <DriverId> DebugCmd <debugging_flags>
+
+<DriverId> default is HiSax, if you didn't specify one.
+
+DebugCmd is 1 for generic debugging
+ 11 for layer 1 development debugging
+ 13 for layer 3 development debugging
+
+where <debugging_flags> is the integer sum of the following debugging
+options you wish enabled:
+
+With DebugCmd set to 1:
+
+ 0x0001 Link-level <--> hardware-level communication
+ 0x0002 Top state machine
+ 0x0004 D-Channel Frames for isdnlog
+ 0x0008 D-Channel Q.921
+ 0x0010 B-Channel X.75
+ 0x0020 D-Channel l2
+ 0x0040 B-Channel l2
+ 0x0080 D-Channel link state debugging
+ 0x0100 B-Channel link state debugging
+ 0x0200 TEI debug
+ 0x0400 LOCK debug in callc.c
+ 0x0800 More paranoid debug in callc.c (not for normal use)
+ 0x1000 D-Channel l1 state debugging
+ 0x2000 B-Channel l1 state debugging
+
+With DebugCmd set to 11:
+
+ 0x0001 Warnings (default: on)
+ 0x0002 IRQ status
+ 0x0004 ISAC
+ 0x0008 ISAC FIFO
+ 0x0010 HSCX
+ 0x0020 HSCX FIFO (attention: full B-Channel output!)
+ 0x0040 D-Channel LAPD frame types
+ 0x0080 IPAC debug
+ 0x0100 HFC receive debug
+ 0x0200 ISAC monitor debug
+ 0x0400 D-Channel frames for isdnlog (set with 1 0x4 too)
+ 0x0800 D-Channel message verbose
+
+With DebugCmd set to 13:
+
+ 1 Warnings (default: on)
+ 2 l3 protocol descriptor errors
+ 4 l3 state machine
+ 8 charge info debugging (1TR6)
+
+For example, 'hisaxctrl HiSax 1 0x3ff' enables full generic debugging.
+
+Because of some obscure problems with some switch equipment, the delay
+between the CONNECT message and sending the first data on the B-channel is now
+configurable with
+
+hisaxctrl <DriverId> 2 <delay>
+<delay> in ms Value between 50 and 800 ms is recommended.
+
+Downloading Firmware
+--------------------
+At the moment, the Sedlbauer speed fax+ is the only card, which
+needs to download firmware.
+The firmware is downloaded with the hisaxctrl tool:
+
+ hisaxctrl <DriverId> 9 <firmware_filename>
+
+<DriverId> default is HiSax, if you didn't specify one,
+
+where <firmware_filename> is the filename of the firmware file.
+
+For example, 'hisaxctrl HiSax 9 ISAR.BIN' downloads the firmware for
+ISAR based cards (like the Sedlbauer speed fax+).
+
+Warning
+-------
+HiSax is a work in progress and may crash your machine.
+For certification look at HiSax.cert file.
+
+Limitations
+-----------
+At this time, HiSax only works on Euro ISDN lines and German 1TR6 lines.
+For leased lines see appendix.
+
+Bugs
+----
+If you find any, please let me know.
+
+
+Thanks
+------
+Special thanks to:
+
+ Emil Stephan for the name HiSax which is a mix of HSCX and ISAC.
+
+ Fritz Elfert, Jan den Ouden, Michael Hipp, Michael Wein,
+ Andreas Kool, Pekka Sarnila, Sim Yskes, Johan Myrre'en,
+ Klaus-Peter Nischke (ITK AG), Christof Petig, Werner Fehn (ELSA GmbH),
+ Volker Schmidt
+ Edgar Toernig and Marcus Niemann for the Sedlbauer driver
+ Stephan von Krawczynski
+ Juergen Quade for the Leased Line part
+ Klaus Lichtenwalder (Klaus.Lichtenwalder@WebForum.DE), for ELSA PCMCIA support
+ Enrik Berkhan (enrik@starfleet.inka.de) for S0BOX specific stuff
+ Ton van Rosmalen for Teles PCI
+ Petr Novak <petr.novak@i.cz> for Winbond W6692 support
+ Werner Cornelius <werner@isdn4linux.de> for HFC-PCI, HFC-S(+/P) and supplementary services support
+ and more people who are hunting bugs. (If I forgot somebody, please
+ send me a mail).
+
+ Firma ELSA GmbH
+ Firma Eicon.Diehl GmbH
+ Firma Dynalink NL
+ Firma ASUSCOM NETWORK INC. Taiwan
+ Firma S.u.S.E
+ Firma ith Kommunikationstechnik GmbH
+ Firma Traverse Technologie Australia
+ Firma Medusa GmbH (www.medusa.de).
+ Firma Quant-X Austria for sponsoring a DEC Alpha board+CPU
+ Firma Cologne Chip Designs GmbH
+
+ My girl friend and partner in life Ute for her patience with me.
+
+
+Enjoy,
+
+Karsten Keil
+keil@isdn4linux.de
+
+
+Appendix: Teles PCMCIA driver
+-----------------------------
+
+See
+ http://www.stud.uni-wuppertal.de/~ea0141/pcmcia.html
+for instructions.
+
+Appendix: Linux and ISDN-leased lines
+-------------------------------------
+
+Original from Juergen Quade, new version KKe.
+
+Attention NEW VERSION, the old leased line syntax won't work !!!
+
+You can use HiSax to connect your Linux-Box via an ISDN leased line
+to e.g. the Internet:
+
+1. Build a kernel which includes the HiSax driver either as a module
+ or as part of the kernel.
+ cd /usr/src/linux
+ make menuconfig
+ <ISDN subsystem - ISDN support -- HiSax>
+ make clean; make zImage; make modules; make modules_install
+2. Install the new kernel
+ cp /usr/src/linux/arch/i386/boot/zImage /etc/kernel/linux.isdn
+ vi /etc/lilo.conf
+ <add new kernel in the bootable image section>
+ lilo
+3. in case the hisax driver is a "fixed" part of the kernel, configure
+ the driver with lilo:
+ vi /etc/lilo.conf
+ <add HiSax driver parameter in the global section (see below)>
+ lilo
+ Your lilo.conf _might_ look like the following:
+
+ # LILO configuration-file
+ # global section
+ # teles 16.0 on IRQ=5, MEM=0xd8000, PORT=0xd80
+ append="hisax=1,3,5,0xd8000,0xd80,HiSax"
+ # teles 16.3 (non pnp) on IRQ=15, PORT=0xd80
+ # append="hisax=3,3,5,0xd8000,0xd80,HiSax"
+ boot=/dev/sda
+ compact # faster, but won't work on all systems.
+ linear
+ read-only
+ prompt
+ timeout=100
+ vga = normal # force sane state
+ # Linux bootable partition config begins
+ image = /etc/kernel/linux.isdn
+ root = /dev/sda1
+ label = linux.isdn
+ #
+ image = /etc/kernel/linux-2.0.30
+ root = /dev/sda1
+ label = linux.secure
+
+ In the line starting with "append" you have to adapt the parameters
+ according to your card (see above in this file)
+
+3. boot the new linux.isdn kernel
+4. start the ISDN subsystem:
+ a) load - if necessary - the modules (depends, whether you compiled
+ the ISDN driver as module or not)
+ According to the type of card you have to specify the necessary
+ driver parameter (irq, io, mem, type, protocol).
+ For the leased line the protocol is "3". See the table above for
+ the parameters, which you have to specify depending on your card.
+ b) configure i4l
+ /sbin/isdnctrl addif isdn0
+ # EAZ 1 -- B1 channel 2 --B2 channel
+ /sbin/isdnctrl eaz isdn0 1
+ /sbin/isdnctrl secure isdn0 on
+ /sbin/isdnctrl huptimeout isdn0 0
+ /sbin/isdnctrl l2_prot isdn0 hdlc
+ # Attention you must not set an outgoing number !!! This won't work !!!
+ # The incoming number is LEASED0 for the first card, LEASED1 for the
+ # second and so on.
+ /sbin/isdnctrl addphone isdn0 in LEASED0
+ # Here is no need to bind the channel.
+ c) in case the remote partner is a CISCO:
+ /sbin/isdnctrl encap isdn0 cisco-h
+ d) configure the interface
+ /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP}
+ e) set the routes
+ /sbin/route add -host ${REMOTE_IP} isdn0
+ /sbin/route add default gw ${REMOTE_IP}
+ f) switch the card into leased mode for each used B-channel
+ /sbin/hisaxctrl HiSax 5 1
+
+Remarks:
+a) Use state of the art isdn4k-utils
+
+Here an example script:
+#!/bin/sh
+# Start/Stop ISDN leased line connection
+
+I4L_AS_MODULE=yes
+I4L_REMOTE_IS_CISCO=no
+I4L_MODULE_PARAMS="type=16 io=0x268 irq=7 "
+I4L_DEBUG=no
+I4L_LEASED_128K=yes
+LOCAL_IP=192.168.1.1
+REMOTE_IP=192.168.2.1
+
+case "$1" in
+ start)
+ echo "Starting ISDN ..."
+ if [ ${I4L_AS_MODULE} = "yes" ]; then
+ echo "loading modules..."
+ /sbin/modprobe hisax ${I4L_MODULE_PARAMS}
+ fi
+ # configure interface
+ /sbin/isdnctrl addif isdn0
+ /sbin/isdnctrl secure isdn0 on
+ if [ ${I4L_DEBUG} = "yes" ]; then
+ /sbin/isdnctrl verbose 7
+ /sbin/hisaxctrl HiSax 1 0xffff
+ /sbin/hisaxctrl HiSax 11 0xff
+ cat /dev/isdnctrl >/tmp/lea.log &
+ fi
+ if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then
+ /sbin/isdnctrl encap isdn0 cisco-h
+ fi
+ /sbin/isdnctrl huptimeout isdn0 0
+ # B-CHANNEL 1
+ /sbin/isdnctrl eaz isdn0 1
+ /sbin/isdnctrl l2_prot isdn0 hdlc
+ # 1. card
+ /sbin/isdnctrl addphone isdn0 in LEASED0
+ if [ ${I4L_LEASED_128K} = "yes" ]; then
+ /sbin/isdnctrl addslave isdn0 isdn0s
+ /sbin/isdnctrl secure isdn0s on
+ /sbin/isdnctrl huptimeout isdn0s 0
+ # B-CHANNEL 2
+ /sbin/isdnctrl eaz isdn0s 2
+ /sbin/isdnctrl l2_prot isdn0s hdlc
+ # 1. card
+ /sbin/isdnctrl addphone isdn0s in LEASED0
+ if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then
+ /sbin/isdnctrl encap isdn0s cisco-h
+ fi
+ fi
+ /sbin/isdnctrl dialmode isdn0 manual
+ # configure tcp/ip
+ /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP}
+ /sbin/route add -host ${REMOTE_IP} isdn0
+ /sbin/route add default gw ${REMOTE_IP}
+ # switch to leased mode
+ # B-CHANNEL 1
+ /sbin/hisaxctrl HiSax 5 1
+ if [ ${I4L_LEASED_128K} = "yes" ]; then
+ # B-CHANNEL 2
+ sleep 10; /* Wait for master */
+ /sbin/hisaxctrl HiSax 5 2
+ fi
+ ;;
+ stop)
+ /sbin/ifconfig isdn0 down
+ /sbin/isdnctrl delif isdn0
+ if [ ${I4L_DEBUG} = "yes" ]; then
+ killall cat
+ fi
+ if [ ${I4L_AS_MODULE} = "yes" ]; then
+ /sbin/rmmod hisax
+ /sbin/rmmod isdn
+ /sbin/rmmod ppp
+ /sbin/rmmod slhc
+ fi
+ ;;
+ *)
+ echo "Usage: $0 {start|stop}"
+ exit 1
+esac
+exit 0