| /* |
| * Copyright (c) 2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &soc { |
| |
| led_flash0: qcom,camera-led-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-led-flash"; |
| qcom,flash-type = <1>; |
| qcom,flash-source = <&pm8226_flash0>; |
| qcom,torch-source = <&pm8226_torch>; |
| }; |
| }; |
| |
| &cci { |
| |
| actuator0: qcom,actuator@6e { |
| cell-index = <3>; |
| reg = <0x6c>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| eeprom0: qcom,eeprom@6c { |
| cell-index = <0>; |
| reg = <0x6c 0x0>; |
| qcom,eeprom-name = "truly_cm7700"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x6c>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <9>; |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x3d84 2 0x8 1 1>; |
| qcom,pageen1 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <32 0x3d00 2 0 1 0>; |
| qcom,page2 = <1 0x3d84 2 0x9 1 1>; |
| qcom,pageen2 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <32 0x3d00 2 0 1 0>; |
| qcom,page3 = <1 0x3d84 2 0xa 1 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <32 0x3d00 2 0 1 0>; |
| qcom,page4 = <1 0x3d84 2 0xb 1 1>; |
| qcom,pageen4 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <32 0x3d00 2 0 1 0>; |
| qcom,page5 = <1 0x3d84 2 0xc 1 1>; |
| qcom,pageen5 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <32 0x3d00 2 0 1 0>; |
| qcom,page6 = <1 0x3d84 2 0xd 1 1>; |
| qcom,pageen6 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <32 0x3d00 2 0 1 0>; |
| qcom,page7 = <1 0x3d84 2 0xe 1 1>; |
| qcom,pageen7 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll7 = <0 0x0 2 0 1 1>; |
| qcom,mem7 = <32 0x3d00 2 0 1 0>; |
| qcom,page8 = <1 0x3d84 2 0xf 1 1>; |
| qcom,pageen8 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll8 = <0 0x0 2 0 1 1>; |
| qcom,mem8 = <32 0x3d00 2 0 1 0>; |
| |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio"; |
| qcom,cam-vreg-type = <0 1>; |
| qcom,cam-vreg-min-voltage = <1200000 0>; |
| qcom,cam-vreg-max-voltage = <1200000 0>; |
| qcom,cam-vreg-op-mode = <200000 0>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_clk", |
| "sensor_gpio", "sensor_gpio"; |
| qcom,cam-power-seq-val = "cam_vdig", |
| "cam_vio", "sensor_cam_mclk", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby"; |
| qcom,cam-power-seq-cfg-val = <1 1 24000000 1 1>; |
| qcom,cam-power-seq-delay = <1 1 5 5 10>; |
| }; |
| |
| qcom,camera@6f { |
| compatible = "qcom,ov8825"; |
| reg = <0x6f>; |
| qcom,slave-id = <0x6c 0x300a 0x8825>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov8825"; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vaf-supply = <&pm8226_l15>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1f>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| |
| actuator1: qcom,actuator@18 { |
| cell-index = <4>; |
| reg = <0x18>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| eeprom1: qcom,eeprom@18{ |
| cell-index = <1>; |
| reg = <0x18 0x0>; |
| qcom,eeprom-name = "sunny_p12v01m"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x20>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <16>; |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x3d84 2 0xc1 1 1>; |
| qcom,pageen1 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <16 0x3d00 2 0 1 0>; |
| qcom,page2 = <1 0x3d84 2 0xc2 1 1>; |
| qcom,pageen2 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <16 0x3d00 2 0 1 0>; |
| qcom,page3 = <1 0x3d84 2 0xc3 1 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <16 0x3d00 2 0 1 0>; |
| qcom,page4 = <1 0x3d84 2 0xc4 1 1>; |
| qcom,pageen4 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <16 0x3d00 2 0 1 0>; |
| qcom,page5 = <1 0x3d84 2 0xc5 1 1>; |
| qcom,pageen5 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <16 0x3d00 2 0 1 0>; |
| qcom,page6 = <1 0x3d84 2 0xc6 1 1>; |
| qcom,pageen6 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <16 0x3d00 2 0 1 0>; |
| qcom,page7 = <1 0x3d84 2 0xc7 1 1>; |
| qcom,pageen7 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll7 = <0 0x0 2 0 1 1>; |
| qcom,mem7 = <16 0x3d00 2 0 1 0>; |
| qcom,page8 = <1 0x3d84 2 0xc8 1 1>; |
| qcom,pageen8 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll8 = <0 0x0 2 0 1 1>; |
| qcom,mem8 = <16 0x3d00 2 0 1 0>; |
| qcom,page9 = <1 0x3d84 2 0xc9 1 1>; |
| qcom,pageen9 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll9 = <0 0x0 2 0 1 1>; |
| qcom,mem9 = <16 0x3d00 2 0 1 0>; |
| qcom,page10 = <1 0x3d84 2 0xca 1 1>; |
| qcom,pageen10 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll10 = <0 0x0 2 0 1 1>; |
| qcom,mem10 = <16 0x3d00 2 0 1 0>; |
| qcom,page11 = <1 0x3d84 2 0xcb 1 1>; |
| qcom,pageen11 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll11 = <0 0x0 2 0 1 1>; |
| qcom,mem11 = <16 0x3d00 2 0 1 0>; |
| qcom,page12 = <1 0x3d84 2 0xcc 1 1>; |
| qcom,pageen12 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll12 = <0 0x0 2 0 1 1>; |
| qcom,mem12 = <16 0x3d00 2 0 1 0>; |
| qcom,page13 = <1 0x3d84 2 0xcd 1 1>; |
| qcom,pageen13 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll13 = <0 0x0 2 0 1 1>; |
| qcom,mem13 = <16 0x3d00 2 0 1 0>; |
| qcom,page14 = <1 0x3d84 2 0xce 1 1>; |
| qcom,pageen14 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll14 = <0 0x0 2 0 1 1>; |
| qcom,mem14 = <16 0x3d00 2 0 1 0>; |
| qcom,page15 = <1 0x3d84 2 0xcf 1 1>; |
| qcom,pageen15 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll15 = <0 0x0 2 0 1 1>; |
| qcom,mem15 = <16 0x3d00 2 0 1 0>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vana-supply = <&pm8226_l19>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <1 0>; |
| qcom,cam-vreg-min-voltage = <0 2850000>; |
| qcom,cam-vreg-max-voltage = <0 2850000>; |
| qcom,cam-vreg-op-mode = <0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>, |
| <&msmgpio 22 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_gpio", |
| "sensor_gpio", "sensor_gpio" , "sensor_clk"; |
| qcom,cam-power-seq-val = "cam_vio", "cam_vana","sensor_gpio_vdig", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby","sensor_cam_mclk" ; |
| qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <1 1 10 10 10 5>; |
| }; |
| |
| qcom,camera@6c { |
| compatible = "qcom,ov12830"; |
| reg = <0x6c>; |
| qcom,slave-id = <0x20 0x300a 0xc830>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator1>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom1>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "skuf_ov12830_p12v01c"; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vaf-supply = <&pm8226_l15>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-op-mode = <120000 0 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>, |
| <&msmgpio 22 0>, |
| <&msmgpio 34 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-af-pwdm = <4>; |
| qcom,gpio-req-tbl-num = <0 1 2 3 4>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY", |
| "CAM_VDIG", |
| "CAM_AF_PWDM"; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1f>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| |
| qcom,camera@6d { |
| compatible = "qcom,ov9724"; |
| reg = <0x6d>; |
| qcom,slave-id = <0x20 0x0 0x9724>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "ov9724"; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| eeprom2: qcom,eeprom@6b{ |
| cell-index = <2>; |
| reg = <0x6b 0x0>; |
| qcom,eeprom-name = "sunny_p5v23c"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x6c>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <7>; |
| |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| |
| qcom,page1 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <0 0x0 2 0 1 0>; |
| qcom,page2 = <1 0x3d85 2 0x00 1 1>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <0 0x0 2 0 1 0>; |
| qcom,page3 = <1 0x3d86 2 0x0f 1 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <16 0x3d00 2 0 1 0>; |
| |
| qcom,page4 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <0 0x0 2 0 1 0>; |
| qcom,page5 = <1 0x3d85 2 0x10 1 1>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <0 0x0 2 0 1 0>; |
| qcom,page6 = <1 0x3d86 2 0x1f 1 1>; |
| qcom,pageen6 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <16 0x3d00 2 0 1 0>; |
| |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vana-supply = <&pm8226_l19>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>, |
| <&msmgpio 21 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_gpio", |
| "sensor_gpio", "sensor_gpio" , "sensor_clk"; |
| qcom,cam-power-seq-val = "cam_vio", "cam_vana","sensor_gpio_vdig", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby","sensor_cam_mclk" ; |
| qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <1 1 10 10 10 5>; |
| }; |
| |
| qcom,camera@6a { |
| compatible = "ovti,ov5648"; |
| reg = <0x6a>; |
| qcom,slave-id = <0x6c 0x300a 0x5648>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,eeprom-src = <&eeprom2>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "skuf_ov5648_p5v23c"; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>, |
| <&msmgpio 21 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| }; |