Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 6ceb775..d2064a0 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -397,7 +397,7 @@
* @is_raid: [flag] 1 = raid object, 0 = sas object
*
* Determines whether this device should be first reported device to
- * to scsi-ml or sas transport, this purpose is for persistant boot device.
+ * to scsi-ml or sas transport, this purpose is for persistent boot device.
* There are primary, alternate, and current entries in bios page 2. The order
* priority is primary, alternate, then current. This routine saves
* the corresponding device object and is_raid flag in the ioc object.
@@ -2671,10 +2671,10 @@
* @handle: device handle
* Context: interrupt time.
*
- * This code is to initiate the device removal handshake protocal
+ * This code is to initiate the device removal handshake protocol
* with controller firmware. This function will issue target reset
* using high priority request queue. It will send a sas iounit
- * controll request (MPI2_SAS_OP_REMOVE_DEVICE) from this completion.
+ * control request (MPI2_SAS_OP_REMOVE_DEVICE) from this completion.
*
* This is designed to send muliple task management request at the same
* time to the fifo. If the fifo is full, we will append the request,
@@ -2749,9 +2749,9 @@
* @reply: reply message frame(lower 32bit addr)
* Context: interrupt time.
*
- * This is the sas iounit controll completion routine.
+ * This is the sas iounit control completion routine.
* This code is part of the code to initiate the device removal
- * handshake protocal with controller firmware.
+ * handshake protocol with controller firmware.
*
* Return 1 meaning mf should be freed from _base_interrupt
* 0 means the mf is freed from this function.
@@ -2878,8 +2878,8 @@
*
* This is the target reset completion routine.
* This code is part of the code to initiate the device removal
- * handshake protocal with controller firmware.
- * It will send a sas iounit controll request (MPI2_SAS_OP_REMOVE_DEVICE)
+ * handshake protocol with controller firmware.
+ * It will send a sas iounit control request (MPI2_SAS_OP_REMOVE_DEVICE)
*
* Return 1 meaning mf should be freed from _base_interrupt
* 0 means the mf is freed from this function.
@@ -2984,7 +2984,7 @@
*
* This routine added to better handle cable breaker.
*
- * This handles the case where driver recieves multiple expander
+ * This handles the case where driver receives multiple expander
* add and delete events in a single shot. When there is a delete event
* the routine will void any pending add events waiting in the event queue.
*
@@ -3511,7 +3511,7 @@
#ifdef CONFIG_SCSI_MPT2SAS_LOGGING
/**
- * _scsih_scsi_ioc_info - translated non-successfull SCSI_IO request
+ * _scsih_scsi_ioc_info - translated non-successful SCSI_IO request
* @ioc: per adapter object
* @scmd: pointer to scsi command object
* @mpi_reply: reply mf payload returned from firmware
@@ -5138,7 +5138,7 @@
unsigned long flags;
int r;
- dewtprintk(ioc, printk(MPT2SAS_INFO_FMT "broadcast primative: "
+ dewtprintk(ioc, printk(MPT2SAS_INFO_FMT "broadcast primitive: "
"phy number(%d), width(%d)\n", ioc->name, event_data->PhyNum,
event_data->PortWidth));
dtmprintk(ioc, printk(MPT2SAS_INFO_FMT "%s: enter\n", ioc->name,