forcedeth: Change reg_delay arguments and use
Move the printk out of reg_delay and make
the callers emit a message on error.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c
index 2fd1ae9..e5f9d4b 100644
--- a/drivers/net/forcedeth.c
+++ b/drivers/net/forcedeth.c
@@ -948,7 +948,7 @@
}
static int reg_delay(struct net_device *dev, int offset, u32 mask, u32 target,
- int delay, int delaymax, const char *msg)
+ int delay, int delaymax)
{
u8 __iomem *base = get_hwbase(dev);
@@ -956,11 +956,8 @@
do {
udelay(delay);
delaymax -= delay;
- if (delaymax < 0) {
- if (msg)
- printk("%s", msg);
+ if (delaymax < 0)
return 1;
- }
} while ((readl(base + offset) & mask) != target);
return 0;
}
@@ -1141,9 +1138,9 @@
writel(reg, base + NvRegMIIControl);
if (reg_delay(dev, NvRegMIIControl, NVREG_MIICTL_INUSE, 0,
- NV_MIIPHY_DELAY, NV_MIIPHY_DELAYMAX, NULL)) {
+ NV_MIIPHY_DELAY, NV_MIIPHY_DELAYMAX)) {
dprintk(KERN_DEBUG "%s: mii_rw of reg %d at PHY %d timed out.\n",
- dev->name, miireg, addr);
+ dev->name, miireg, addr);
retval = -1;
} else if (value != MII_READ) {
/* it was a write operation - fewer failures are detectable */
@@ -1539,9 +1536,9 @@
else
rx_ctrl |= NVREG_RCVCTL_RX_PATH_EN;
writel(rx_ctrl, base + NvRegReceiverControl);
- reg_delay(dev, NvRegReceiverStatus, NVREG_RCVSTAT_BUSY, 0,
- NV_RXSTOP_DELAY1, NV_RXSTOP_DELAY1MAX,
- KERN_INFO "nv_stop_rx: ReceiverStatus remained busy");
+ if (reg_delay(dev, NvRegReceiverStatus, NVREG_RCVSTAT_BUSY, 0,
+ NV_RXSTOP_DELAY1, NV_RXSTOP_DELAY1MAX))
+ printk(KERN_INFO "nv_stop_rx: ReceiverStatus remained busy");
udelay(NV_RXSTOP_DELAY2);
if (!np->mac_in_use)
@@ -1574,9 +1571,9 @@
else
tx_ctrl |= NVREG_XMITCTL_TX_PATH_EN;
writel(tx_ctrl, base + NvRegTransmitterControl);
- reg_delay(dev, NvRegTransmitterStatus, NVREG_XMITSTAT_BUSY, 0,
- NV_TXSTOP_DELAY1, NV_TXSTOP_DELAY1MAX,
- KERN_INFO "nv_stop_tx: TransmitterStatus remained busy");
+ if (reg_delay(dev, NvRegTransmitterStatus, NVREG_XMITSTAT_BUSY, 0,
+ NV_TXSTOP_DELAY1, NV_TXSTOP_DELAY1MAX))
+ printk(KERN_INFO "nv_stop_tx: TransmitterStatus remained busy");
udelay(NV_TXSTOP_DELAY2);
if (!np->mac_in_use)
@@ -5190,9 +5187,10 @@
writel(np->vlanctl_bits, base + NvRegVlanControl);
pci_push(base);
writel(NVREG_TXRXCTL_BIT1|np->txrxctl_bits, base + NvRegTxRxControl);
- reg_delay(dev, NvRegUnknownSetupReg5, NVREG_UNKSETUP5_BIT31, NVREG_UNKSETUP5_BIT31,
- NV_SETUP5_DELAY, NV_SETUP5_DELAYMAX,
- KERN_INFO "open: SetupReg5, Bit 31 remained off\n");
+ if (reg_delay(dev, NvRegUnknownSetupReg5,
+ NVREG_UNKSETUP5_BIT31, NVREG_UNKSETUP5_BIT31,
+ NV_SETUP5_DELAY, NV_SETUP5_DELAYMAX))
+ printk(KERN_INFO "open: SetupReg5, Bit 31 remained off\n");
writel(0, base + NvRegMIIMask);
writel(NVREG_IRQSTAT_MASK, base + NvRegIrqStatus);