Merge branch 'master' into upstream
diff --git a/Documentation/networking/LICENSE.qla3xxx b/Documentation/networking/LICENSE.qla3xxx
new file mode 100644
index 0000000..2f2077e
--- /dev/null
+++ b/Documentation/networking/LICENSE.qla3xxx
@@ -0,0 +1,46 @@
+Copyright (c) 2003-2006 QLogic Corporation
+QLogic Linux Networking HBA Driver
+
+This program includes a device driver for Linux 2.6 that may be
+distributed with QLogic hardware specific firmware binary file.
+You may modify and redistribute the device driver code under the
+GNU General Public License as published by the Free Software
+Foundation (version 2 or a later version).
+
+You may redistribute the hardware specific firmware binary file
+under the following terms:
+
+ 1. Redistribution of source code (only if applicable),
+ must retain the above copyright notice, this list of
+ conditions and the following disclaimer.
+
+ 2. Redistribution in binary form must reproduce the above
+ copyright notice, this list of conditions and the
+ following disclaimer in the documentation and/or other
+ materials provided with the distribution.
+
+ 3. The name of QLogic Corporation may not be used to
+ endorse or promote products derived from this software
+ without specific prior written permission
+
+REGARDLESS OF WHAT LICENSING MECHANISM IS USED OR APPLICABLE,
+THIS PROGRAM IS PROVIDED BY QLOGIC CORPORATION "AS IS'' AND ANY
+EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
+PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
+BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
+EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
+TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGE.
+
+USER ACKNOWLEDGES AND AGREES THAT USE OF THIS PROGRAM WILL NOT
+CREATE OR GIVE GROUNDS FOR A LICENSE BY IMPLICATION, ESTOPPEL, OR
+OTHERWISE IN ANY INTELLECTUAL PROPERTY RIGHTS (PATENT, COPYRIGHT,
+TRADE SECRET, MASK WORK, OR OTHER PROPRIETARY RIGHT) EMBODIED IN
+ANY OTHER QLOGIC HARDWARE OR SOFTWARE EITHER SOLELY OR IN
+COMBINATION WITH THIS PROGRAM.
+
diff --git a/MAINTAINERS b/MAINTAINERS
index 25cd707..6c399b8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2366,6 +2366,12 @@
L: linux-scsi@vger.kernel.org
S: Supported
+QLOGIC QLA3XXX NETWORK DRIVER
+P: Ron Mercer
+M: linux-driver@qlogic.com
+L: netdev@vger.kernel.org
+S: Supported
+
QNX4 FILESYSTEM
P: Anders Larsen
M: al@alarsen.net
@@ -2616,6 +2622,18 @@
M: nico@cam.org
S: Maintained
+SOFTMAC LAYER (IEEE 802.11)
+P: Johannes Berg
+M: johannes@sipsolutions.net
+P: Joe Jezak
+M: josejx@gentoo.org
+P: Daniel Drake
+M: dsd@gentoo.org
+W: http://softmac.sipsolutions.net/
+L: softmac-dev@sipsolutions.net
+L: netdev@vger.kernel.org
+S: Maintained
+
SOFTWARE RAID (Multiple Disks) SUPPORT
P: Ingo Molnar
M: mingo@redhat.com
@@ -3341,6 +3359,15 @@
L: linux-hams@vger.kernel.org
S: Maintained
+ZD1211RW WIRELESS DRIVER
+P: Daniel Drake
+M: dsd@gentoo.org
+P: Ulrich Kunitz
+M: kune@deine-taler.de
+W: http://zd1211.ath.cx/wiki/DriverRewrite
+L: zd1211-devs@lists.sourceforge.net (subscribers-only)
+S: Maintained
+
ZF MACHZ WATCHDOG
P: Fernando Fuganti
M: fuganti@netbank.com.br
diff --git a/drivers/isdn/i4l/Kconfig b/drivers/isdn/i4l/Kconfig
index a4f7288..3ef567b 100644
--- a/drivers/isdn/i4l/Kconfig
+++ b/drivers/isdn/i4l/Kconfig
@@ -5,6 +5,7 @@
config ISDN_PPP
bool "Support synchronous PPP"
depends on INET
+ select SLHC
help
Over digital connections such as ISDN, there is no need to
synchronize sender and recipient's clocks with start and stop bits
diff --git a/drivers/net/3c501.c b/drivers/net/3c501.c
index 07136ec..d7b115a 100644
--- a/drivers/net/3c501.c
+++ b/drivers/net/3c501.c
@@ -120,7 +120,6 @@
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/errno.h>
-#include <linux/config.h> /* for CONFIG_IP_MULTICAST */
#include <linux/spinlock.h>
#include <linux/ethtool.h>
#include <linux/delay.h>
diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c
index 80e8ca0..7c23813 100644
--- a/drivers/net/3c59x.c
+++ b/drivers/net/3c59x.c
@@ -3169,7 +3169,7 @@
{
int pci_rc, eisa_rc;
- pci_rc = pci_module_init(&vortex_driver);
+ pci_rc = pci_register_driver(&vortex_driver);
eisa_rc = vortex_eisa_init();
if (pci_rc == 0)
diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c
index 1428bb7..4c2e763 100644
--- a/drivers/net/8139cp.c
+++ b/drivers/net/8139cp.c
@@ -2098,7 +2098,7 @@
#ifdef MODULE
printk("%s", version);
#endif
- return pci_module_init (&cp_driver);
+ return pci_register_driver(&cp_driver);
}
static void __exit cp_exit (void)
diff --git a/drivers/net/8139too.c b/drivers/net/8139too.c
index e4f4eaf..2a70774 100644
--- a/drivers/net/8139too.c
+++ b/drivers/net/8139too.c
@@ -2629,7 +2629,7 @@
printk (KERN_INFO RTL8139_DRIVER_NAME "\n");
#endif
- return pci_module_init (&rtl8139_pci_driver);
+ return pci_register_driver(&rtl8139_pci_driver);
}
diff --git a/drivers/net/8390.c b/drivers/net/8390.c
index d2935ae..3eb7048 100644
--- a/drivers/net/8390.c
+++ b/drivers/net/8390.c
@@ -299,7 +299,7 @@
* Slow phase with lock held.
*/
- disable_irq_nosync(dev->irq);
+ disable_irq_nosync_lockdep(dev->irq);
spin_lock(&ei_local->page_lock);
@@ -338,7 +338,7 @@
netif_stop_queue(dev);
outb_p(ENISR_ALL, e8390_base + EN0_IMR);
spin_unlock(&ei_local->page_lock);
- enable_irq(dev->irq);
+ enable_irq_lockdep(dev->irq);
ei_local->stat.tx_errors++;
return 1;
}
@@ -379,7 +379,7 @@
outb_p(ENISR_ALL, e8390_base + EN0_IMR);
spin_unlock(&ei_local->page_lock);
- enable_irq(dev->irq);
+ enable_irq_lockdep(dev->irq);
dev_kfree_skb (skb);
ei_local->stat.tx_bytes += send_length;
@@ -505,9 +505,9 @@
#ifdef CONFIG_NET_POLL_CONTROLLER
void ei_poll(struct net_device *dev)
{
- disable_irq(dev->irq);
+ disable_irq_lockdep(dev->irq);
ei_interrupt(dev->irq, dev, NULL);
- enable_irq(dev->irq);
+ enable_irq_lockdep(dev->irq);
}
#endif
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 30b3671..6f388d9 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1411,6 +1411,22 @@
<file:Documentation/networking/net-modules.txt>. The module will be
called forcedeth.
+config FORCEDETH_NAPI
+ bool "Use Rx and Tx Polling (NAPI) (EXPERIMENTAL)"
+ depends on FORCEDETH && EXPERIMENTAL
+ help
+ NAPI is a new driver API designed to reduce CPU and interrupt load
+ when the driver is receiving lots of packets from the card. It is
+ still somewhat experimental and thus not yet enabled by default.
+
+ If your estimated Rx load is 10kpps or more, or if the card will be
+ deployed on potentially unfriendly networks (e.g. in a firewall),
+ then say Y here.
+
+ See <file:Documentation/networking/NAPI_HOWTO.txt> for more
+ information.
+
+ If in doubt, say N.
config CS89x0
tristate "CS89x0 support"
@@ -2290,6 +2306,15 @@
This enables support for Port 2 of the Marvell MV643XX Gigabit
Ethernet.
+config QLA3XXX
+ tristate "QLogic QLA3XXX Network Driver Support"
+ depends on PCI
+ help
+ This driver supports QLogic ISP3XXX gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called qla3xxx.
+
endmenu
#
@@ -2550,6 +2575,7 @@
config PPP
tristate "PPP (point-to-point protocol) support"
+ select SLHC
---help---
PPP (Point to Point Protocol) is a newer and better SLIP. It serves
the same purpose: sending Internet traffic over telephone (and other
@@ -2730,6 +2756,7 @@
config SLIP_COMPRESSED
bool "CSLIP compressed headers"
depends on SLIP
+ select SLHC
---help---
This protocol is faster than SLIP because it uses compression on the
TCP/IP headers (not on the data itself), but it has to be supported
@@ -2742,6 +2769,12 @@
<http://www.tldp.org/docs.html#howto>, explains how to configure
CSLIP. This won't enlarge your kernel.
+config SLHC
+ tristate
+ help
+ This option enables Van Jacobsen serial line header compression
+ routines.
+
config SLIP_SMART
bool "Keepalive and linefill"
depends on SLIP
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 8427bf9..6ff1764 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -2,10 +2,6 @@
# Makefile for the Linux network (ethercard) device drivers.
#
-ifeq ($(CONFIG_ISDN_PPP),y)
- obj-$(CONFIG_ISDN) += slhc.o
-endif
-
obj-$(CONFIG_E1000) += e1000/
obj-$(CONFIG_IBM_EMAC) += ibm_emac/
obj-$(CONFIG_IXGB) += ixgb/
@@ -113,8 +109,9 @@
obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
+obj-$(CONFIG_QLA3XXX) += qla3xxx.o
-obj-$(CONFIG_PPP) += ppp_generic.o slhc.o
+obj-$(CONFIG_PPP) += ppp_generic.o
obj-$(CONFIG_PPP_ASYNC) += ppp_async.o
obj-$(CONFIG_PPP_SYNC_TTY) += ppp_synctty.o
obj-$(CONFIG_PPP_DEFLATE) += ppp_deflate.o
@@ -123,9 +120,7 @@
obj-$(CONFIG_PPPOE) += pppox.o pppoe.o
obj-$(CONFIG_SLIP) += slip.o
-ifeq ($(CONFIG_SLIP_COMPRESSED),y)
- obj-$(CONFIG_SLIP) += slhc.o
-endif
+obj-$(CONFIG_SLHC) += slhc.o
obj-$(CONFIG_DUMMY) += dummy.o
obj-$(CONFIG_IFB) += ifb.o
diff --git a/drivers/net/acenic.c b/drivers/net/acenic.c
index 1c01e9b..c0f3574 100644
--- a/drivers/net/acenic.c
+++ b/drivers/net/acenic.c
@@ -725,7 +725,7 @@
static int __init acenic_init(void)
{
- return pci_module_init(&acenic_pci_driver);
+ return pci_register_driver(&acenic_pci_driver);
}
static void __exit acenic_exit(void)
diff --git a/drivers/net/amd8111e.c b/drivers/net/amd8111e.c
index ed322a7..2ef8e55 100644
--- a/drivers/net/amd8111e.c
+++ b/drivers/net/amd8111e.c
@@ -2158,7 +2158,7 @@
static int __init amd8111e_init(void)
{
- return pci_module_init(&amd8111e_driver);
+ return pci_register_driver(&amd8111e_driver);
}
static void __exit amd8111e_cleanup(void)
diff --git a/drivers/net/arcnet/com20020-pci.c b/drivers/net/arcnet/com20020-pci.c
index 979a33d..fc256c1 100644
--- a/drivers/net/arcnet/com20020-pci.c
+++ b/drivers/net/arcnet/com20020-pci.c
@@ -177,7 +177,7 @@
static int __init com20020pci_init(void)
{
BUGLVL(D_NORMAL) printk(VERSION);
- return pci_module_init(&com20020pci_driver);
+ return pci_register_driver(&com20020pci_driver);
}
static void __exit com20020pci_cleanup(void)
diff --git a/drivers/net/b44.c b/drivers/net/b44.c
index bea0fc0..17eb291 100644
--- a/drivers/net/b44.c
+++ b/drivers/net/b44.c
@@ -2354,7 +2354,7 @@
dma_desc_align_mask = ~(dma_desc_align_size - 1);
dma_desc_sync_size = max_t(unsigned int, dma_desc_align_size, sizeof(struct dma_desc));
- return pci_module_init(&b44_driver);
+ return pci_register_driver(&b44_driver);
}
static void __exit b44_cleanup(void)
diff --git a/drivers/net/bnx2.c b/drivers/net/bnx2.c
index 652eb05..654b903 100644
--- a/drivers/net/bnx2.c
+++ b/drivers/net/bnx2.c
@@ -6016,7 +6016,7 @@
static int __init bnx2_init(void)
{
- return pci_module_init(&bnx2_pci_driver);
+ return pci_register_driver(&bnx2_pci_driver);
}
static void __exit bnx2_cleanup(void)
diff --git a/drivers/net/cassini.c b/drivers/net/cassini.c
index a31544c..26040ab 100644
--- a/drivers/net/cassini.c
+++ b/drivers/net/cassini.c
@@ -5245,7 +5245,7 @@
else
link_transition_timeout = 0;
- return pci_module_init(&cas_driver);
+ return pci_register_driver(&cas_driver);
}
static void __exit cas_cleanup(void)
diff --git a/drivers/net/chelsio/cxgb2.c b/drivers/net/chelsio/cxgb2.c
index e678724..b6de184 100644
--- a/drivers/net/chelsio/cxgb2.c
+++ b/drivers/net/chelsio/cxgb2.c
@@ -1243,7 +1243,7 @@
static int __init t1_init_module(void)
{
- return pci_module_init(&driver);
+ return pci_register_driver(&driver);
}
static void __exit t1_cleanup_module(void)
diff --git a/drivers/net/defxx.c b/drivers/net/defxx.c
index 91cc8cb..7d06ded 100644
--- a/drivers/net/defxx.c
+++ b/drivers/net/defxx.c
@@ -3444,7 +3444,7 @@
{
int rc_pci, rc_eisa;
- rc_pci = pci_module_init(&dfx_driver);
+ rc_pci = pci_register_driver(&dfx_driver);
if (rc_pci >= 0) dfx_have_pci = 1;
rc_eisa = dfx_eisa_init();
diff --git a/drivers/net/dl2k.c b/drivers/net/dl2k.c
index 402961e..a572c29 100644
--- a/drivers/net/dl2k.c
+++ b/drivers/net/dl2k.c
@@ -1815,7 +1815,7 @@
static int __init
rio_init (void)
{
- return pci_module_init (&rio_driver);
+ return pci_register_driver(&rio_driver);
}
static void __exit
diff --git a/drivers/net/e100.c b/drivers/net/e100.c
index ce850f1..47d9708 100644
--- a/drivers/net/e100.c
+++ b/drivers/net/e100.c
@@ -1,7 +1,7 @@
/*******************************************************************************
- Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
+ Copyright(c) 1999 - 2006 Intel Corporation. All rights reserved.
This program is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the Free
@@ -158,10 +158,10 @@
#define DRV_NAME "e100"
-#define DRV_EXT "-NAPI"
-#define DRV_VERSION "3.5.10-k2"DRV_EXT
+#define DRV_EXT "-NAPI"
+#define DRV_VERSION "3.5.16-k2"DRV_EXT
#define DRV_DESCRIPTION "Intel(R) PRO/100 Network Driver"
-#define DRV_COPYRIGHT "Copyright(c) 1999-2005 Intel Corporation"
+#define DRV_COPYRIGHT "Copyright(c) 1999-2006 Intel Corporation"
#define PFX DRV_NAME ": "
#define E100_WATCHDOG_PERIOD (2 * HZ)
@@ -1395,15 +1395,11 @@
}
if((nic->mac >= mac_82550_D102) || ((nic->flags & ich) &&
- (mdio_read(netdev, nic->mii.phy_id, MII_TPISTATUS) & 0x8000))) {
- /* enable/disable MDI/MDI-X auto-switching.
- MDI/MDI-X auto-switching is disabled for 82551ER/QM chips */
- if((nic->mac == mac_82551_E) || (nic->mac == mac_82551_F) ||
- (nic->mac == mac_82551_10) || (nic->mii.force_media) ||
- !(nic->eeprom[eeprom_cnfg_mdix] & eeprom_mdix_enabled))
- mdio_write(netdev, nic->mii.phy_id, MII_NCONFIG, 0);
- else
- mdio_write(netdev, nic->mii.phy_id, MII_NCONFIG, NCONFIG_AUTO_SWITCH);
+ (mdio_read(netdev, nic->mii.phy_id, MII_TPISTATUS) & 0x8000) &&
+ !(nic->eeprom[eeprom_cnfg_mdix] & eeprom_mdix_enabled))) {
+ /* enable/disable MDI/MDI-X auto-switching. */
+ mdio_write(netdev, nic->mii.phy_id, MII_NCONFIG,
+ nic->mii.force_media ? 0 : NCONFIG_AUTO_SWITCH);
}
return 0;
@@ -1767,11 +1763,10 @@
#define RFD_BUF_LEN (sizeof(struct rfd) + VLAN_ETH_FRAME_LEN)
static int e100_rx_alloc_skb(struct nic *nic, struct rx *rx)
{
- if(!(rx->skb = dev_alloc_skb(RFD_BUF_LEN + NET_IP_ALIGN)))
+ if(!(rx->skb = netdev_alloc_skb(nic->netdev, RFD_BUF_LEN + NET_IP_ALIGN)))
return -ENOMEM;
/* Align, init, and map the RFD. */
- rx->skb->dev = nic->netdev;
skb_reserve(rx->skb, NET_IP_ALIGN);
memcpy(rx->skb->data, &nic->blank_rfd, sizeof(struct rfd));
rx->dma_addr = pci_map_single(nic->pdev, rx->skb->data,
@@ -2147,7 +2142,7 @@
e100_start_receiver(nic, NULL);
- if(!(skb = dev_alloc_skb(ETH_DATA_LEN))) {
+ if(!(skb = netdev_alloc_skb(nic->netdev, ETH_DATA_LEN))) {
err = -ENOMEM;
goto err_loopback_none;
}
@@ -2799,6 +2794,7 @@
/* Detach; put netif into state similar to hotplug unplug. */
netif_poll_enable(netdev);
netif_device_detach(netdev);
+ pci_disable_device(pdev);
/* Request a slot reset. */
return PCI_ERS_RESULT_NEED_RESET;
@@ -2877,7 +2873,7 @@
printk(KERN_INFO PFX "%s, %s\n", DRV_DESCRIPTION, DRV_VERSION);
printk(KERN_INFO PFX "%s\n", DRV_COPYRIGHT);
}
- return pci_module_init(&e100_driver);
+ return pci_register_driver(&e100_driver);
}
static void __exit e100_cleanup_module(void)
diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index d304297..98afa9c 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -242,12 +242,10 @@
struct timer_list watchdog_timer;
struct timer_list phy_info_timer;
struct vlan_group *vlgrp;
- uint16_t mng_vlan_id;
+ uint16_t mng_vlan_id;
uint32_t bd_number;
uint32_t rx_buffer_len;
- uint32_t part_num;
uint32_t wol;
- uint32_t ksp3_port_a;
uint32_t smartspeed;
uint32_t en_mng_pt;
uint16_t link_speed;
@@ -342,7 +340,9 @@
boolean_t tso_force;
#endif
boolean_t smart_power_down; /* phy smart power down */
+ boolean_t quad_port_a;
unsigned long flags;
+ uint32_t eeprom_wol;
};
enum e1000_state_t {
diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c
index 88a82ba..3fccffd 100644
--- a/drivers/net/e1000/e1000_ethtool.c
+++ b/drivers/net/e1000/e1000_ethtool.c
@@ -183,6 +183,9 @@
return -EINVAL;
}
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
if (ecmd->autoneg == AUTONEG_ENABLE) {
hw->autoneg = 1;
if (hw->media_type == e1000_media_type_fiber)
@@ -199,16 +202,20 @@
ADVERTISED_TP;
ecmd->advertising = hw->autoneg_advertised;
} else
- if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex))
+ if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
+ clear_bit(__E1000_RESETTING, &adapter->flags);
return -EINVAL;
+ }
/* reset the link */
- if (netif_running(adapter->netdev))
- e1000_reinit_locked(adapter);
- else
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
e1000_reset(adapter);
+ clear_bit(__E1000_RESETTING, &adapter->flags);
return 0;
}
@@ -238,9 +245,13 @@
{
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ int retval = 0;
adapter->fc_autoneg = pause->autoneg;
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+
if (pause->rx_pause && pause->tx_pause)
hw->fc = e1000_fc_full;
else if (pause->rx_pause && !pause->tx_pause)
@@ -253,15 +264,17 @@
hw->original_fc = hw->fc;
if (adapter->fc_autoneg == AUTONEG_ENABLE) {
- if (netif_running(adapter->netdev))
- e1000_reinit_locked(adapter);
- else
+ if (netif_running(adapter->netdev)) {
+ e1000_down(adapter);
+ e1000_up(adapter);
+ } else
e1000_reset(adapter);
} else
- return ((hw->media_type == e1000_media_type_fiber) ?
- e1000_setup_link(hw) : e1000_force_mac_fc(hw));
+ retval = ((hw->media_type == e1000_media_type_fiber) ?
+ e1000_setup_link(hw) : e1000_force_mac_fc(hw));
- return 0;
+ clear_bit(__E1000_RESETTING, &adapter->flags);
+ return retval;
}
static uint32_t
@@ -415,12 +428,12 @@
regs_buff[23] = regs_buff[18]; /* mdix mode */
e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0);
} else {
- e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
regs_buff[13] = (uint32_t)phy_data; /* cable length */
regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */
regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */
regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */
- e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
regs_buff[17] = (uint32_t)phy_data; /* extended 10bt distance */
regs_buff[18] = regs_buff[13]; /* cable polarity */
regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */
@@ -696,7 +709,6 @@
}
clear_bit(__E1000_RESETTING, &adapter->flags);
-
return 0;
err_setup_tx:
e1000_free_all_rx_resources(adapter);
@@ -881,16 +893,17 @@
*data = 0;
+ /* NOTE: we don't test MSI interrupts here, yet */
/* Hook up test interrupt handler just for this test */
if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED,
- netdev->name, netdev)) {
- shared_int = FALSE;
- } else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
- netdev->name, netdev)){
+ netdev->name, netdev))
+ shared_int = FALSE;
+ else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED,
+ netdev->name, netdev)) {
*data = 1;
return -1;
}
- DPRINTK(PROBE,INFO, "testing %s interrupt\n",
+ DPRINTK(HW, INFO, "testing %s interrupt\n",
(shared_int ? "shared" : "unshared"));
/* Disable all the interrupts */
@@ -1256,11 +1269,10 @@
e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x9140);
/* autoneg off */
e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8140);
- } else if (adapter->hw.phy_type == e1000_phy_gg82563) {
+ } else if (adapter->hw.phy_type == e1000_phy_gg82563)
e1000_write_phy_reg(&adapter->hw,
GG82563_PHY_KMRN_MODE_CTRL,
0x1CC);
- }
ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL);
@@ -1288,9 +1300,9 @@
}
if (adapter->hw.media_type == e1000_media_type_copper &&
- adapter->hw.phy_type == e1000_phy_m88) {
+ adapter->hw.phy_type == e1000_phy_m88)
ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
- } else {
+ else {
/* Set the ILOS bit on the fiber Nic is half
* duplex link is detected. */
stat_reg = E1000_READ_REG(&adapter->hw, STATUS);
@@ -1426,11 +1438,10 @@
case e1000_82546_rev_3:
default:
hw->autoneg = TRUE;
- if (hw->phy_type == e1000_phy_gg82563) {
+ if (hw->phy_type == e1000_phy_gg82563)
e1000_write_phy_reg(hw,
GG82563_PHY_KMRN_MODE_CTRL,
0x180);
- }
e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
if (phy_reg & MII_CR_LOOPBACK) {
phy_reg &= ~MII_CR_LOOPBACK;
@@ -1590,6 +1601,8 @@
return E1000_TEST_LEN;
}
+extern void e1000_power_up_phy(struct e1000_adapter *);
+
static void
e1000_diag_test(struct net_device *netdev,
struct ethtool_test *eth_test, uint64_t *data)
@@ -1606,6 +1619,8 @@
uint8_t forced_speed_duplex = adapter->hw.forced_speed_duplex;
uint8_t autoneg = adapter->hw.autoneg;
+ DPRINTK(HW, INFO, "offline testing starting\n");
+
/* Link test performed before hardware reset so autoneg doesn't
* interfere with test result */
if (e1000_link_test(adapter, &data[4]))
@@ -1629,6 +1644,8 @@
eth_test->flags |= ETH_TEST_FL_FAILED;
e1000_reset(adapter);
+ /* make sure the phy is powered up */
+ e1000_power_up_phy(adapter);
if (e1000_loopback_test(adapter, &data[3]))
eth_test->flags |= ETH_TEST_FL_FAILED;
@@ -1642,6 +1659,7 @@
if (if_running)
dev_open(netdev);
} else {
+ DPRINTK(HW, INFO, "online testing starting\n");
/* Online tests */
if (e1000_link_test(adapter, &data[4]))
eth_test->flags |= ETH_TEST_FL_FAILED;
@@ -1657,14 +1675,12 @@
msleep_interruptible(4 * 1000);
}
-static void
-e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+static int e1000_wol_exclusion(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
{
- struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ int retval = 1; /* fail by default */
- switch (adapter->hw.device_id) {
- case E1000_DEV_ID_82542:
+ switch (hw->device_id) {
case E1000_DEV_ID_82543GC_FIBER:
case E1000_DEV_ID_82543GC_COPPER:
case E1000_DEV_ID_82544EI_FIBER:
@@ -1672,52 +1688,87 @@
case E1000_DEV_ID_82545EM_FIBER:
case E1000_DEV_ID_82545EM_COPPER:
case E1000_DEV_ID_82546GB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_PCIE:
+ /* these don't support WoL at all */
wol->supported = 0;
- wol->wolopts = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ case E1000_DEV_ID_82571EB_FIBER:
+ case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82571EB_COPPER:
+ /* Wake events not supported on port B */
+ if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ /* quad port adapters only support WoL on port A */
+ if (!adapter->quad_port_a) {
+ wol->supported = 0;
+ break;
+ }
+ /* return success for non excluded adapter ports */
+ retval = 0;
+ break;
+ default:
+ /* dual port cards only support WoL on port A from now on
+ * unless it was enabled in the eeprom for port B
+ * so exclude FUNC_1 ports from having WoL enabled */
+ if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1 &&
+ !adapter->eeprom_wol) {
+ wol->supported = 0;
+ break;
+ }
+
+ retval = 0;
+ }
+
+ return retval;
+}
+
+static void
+e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol)
+{
+ struct e1000_adapter *adapter = netdev_priv(netdev);
+
+ wol->supported = WAKE_UCAST | WAKE_MCAST |
+ WAKE_BCAST | WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ /* this function will set ->supported = 0 and return 1 if wol is not
+ * supported by this hardware */
+ if (e1000_wol_exclusion(adapter, wol))
return;
+ /* apply any specific unsupported masks here */
+ switch (adapter->hw.device_id) {
case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
- /* device id 10B5 port-A supports wol */
- if (!adapter->ksp3_port_a) {
- wol->supported = 0;
- return;
- }
- /* KSP3 does not suppport UCAST wake-ups for any interface */
- wol->supported = WAKE_MCAST | WAKE_BCAST | WAKE_MAGIC;
+ /* KSP3 does not suppport UCAST wake-ups */
+ wol->supported &= ~WAKE_UCAST;
if (adapter->wol & E1000_WUFC_EX)
DPRINTK(DRV, ERR, "Interface does not support "
"directed (unicast) frame wake-up packets\n");
- wol->wolopts = 0;
- goto do_defaults;
-
- case E1000_DEV_ID_82546EB_FIBER:
- case E1000_DEV_ID_82546GB_FIBER:
- case E1000_DEV_ID_82571EB_FIBER:
- /* Wake events only supported on port A for dual fiber */
- if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) {
- wol->supported = 0;
- wol->wolopts = 0;
- return;
- }
- /* Fall Through */
-
+ break;
default:
- wol->supported = WAKE_UCAST | WAKE_MCAST |
- WAKE_BCAST | WAKE_MAGIC;
- wol->wolopts = 0;
-
-do_defaults:
- if (adapter->wol & E1000_WUFC_EX)
- wol->wolopts |= WAKE_UCAST;
- if (adapter->wol & E1000_WUFC_MC)
- wol->wolopts |= WAKE_MCAST;
- if (adapter->wol & E1000_WUFC_BC)
- wol->wolopts |= WAKE_BCAST;
- if (adapter->wol & E1000_WUFC_MAG)
- wol->wolopts |= WAKE_MAGIC;
- return;
+ break;
}
+
+ if (adapter->wol & E1000_WUFC_EX)
+ wol->wolopts |= WAKE_UCAST;
+ if (adapter->wol & E1000_WUFC_MC)
+ wol->wolopts |= WAKE_MCAST;
+ if (adapter->wol & E1000_WUFC_BC)
+ wol->wolopts |= WAKE_BCAST;
+ if (adapter->wol & E1000_WUFC_MAG)
+ wol->wolopts |= WAKE_MAGIC;
+
+ return;
}
static int
@@ -1726,52 +1777,36 @@
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- switch (adapter->hw.device_id) {
- case E1000_DEV_ID_82542:
- case E1000_DEV_ID_82543GC_FIBER:
- case E1000_DEV_ID_82543GC_COPPER:
- case E1000_DEV_ID_82544EI_FIBER:
- case E1000_DEV_ID_82546EB_QUAD_COPPER:
- case E1000_DEV_ID_82546GB_QUAD_COPPER:
- case E1000_DEV_ID_82545EM_FIBER:
- case E1000_DEV_ID_82545EM_COPPER:
+ if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
+ return -EOPNOTSUPP;
+
+ if (e1000_wol_exclusion(adapter, wol))
return wol->wolopts ? -EOPNOTSUPP : 0;
+ switch (hw->device_id) {
case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
- /* device id 10B5 port-A supports wol */
- if (!adapter->ksp3_port_a)
- return wol->wolopts ? -EOPNOTSUPP : 0;
-
if (wol->wolopts & WAKE_UCAST) {
DPRINTK(DRV, ERR, "Interface does not support "
"directed (unicast) frame wake-up packets\n");
return -EOPNOTSUPP;
}
-
- case E1000_DEV_ID_82546EB_FIBER:
- case E1000_DEV_ID_82546GB_FIBER:
- case E1000_DEV_ID_82571EB_FIBER:
- /* Wake events only supported on port A for dual fiber */
- if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
- return wol->wolopts ? -EOPNOTSUPP : 0;
- /* Fall Through */
-
+ break;
default:
- if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE))
- return -EOPNOTSUPP;
-
- adapter->wol = 0;
-
- if (wol->wolopts & WAKE_UCAST)
- adapter->wol |= E1000_WUFC_EX;
- if (wol->wolopts & WAKE_MCAST)
- adapter->wol |= E1000_WUFC_MC;
- if (wol->wolopts & WAKE_BCAST)
- adapter->wol |= E1000_WUFC_BC;
- if (wol->wolopts & WAKE_MAGIC)
- adapter->wol |= E1000_WUFC_MAG;
+ break;
}
+ /* these settings will always override what we currently have */
+ adapter->wol = 0;
+
+ if (wol->wolopts & WAKE_UCAST)
+ adapter->wol |= E1000_WUFC_EX;
+ if (wol->wolopts & WAKE_MCAST)
+ adapter->wol |= E1000_WUFC_MC;
+ if (wol->wolopts & WAKE_BCAST)
+ adapter->wol |= E1000_WUFC_BC;
+ if (wol->wolopts & WAKE_MAGIC)
+ adapter->wol |= E1000_WUFC_MAG;
+
return 0;
}
@@ -1895,8 +1930,8 @@
.get_regs = e1000_get_regs,
.get_wol = e1000_get_wol,
.set_wol = e1000_set_wol,
- .get_msglevel = e1000_get_msglevel,
- .set_msglevel = e1000_set_msglevel,
+ .get_msglevel = e1000_get_msglevel,
+ .set_msglevel = e1000_set_msglevel,
.nway_reset = e1000_nway_reset,
.get_link = ethtool_op_get_link,
.get_eeprom_len = e1000_get_eeprom_len,
@@ -1904,17 +1939,17 @@
.set_eeprom = e1000_set_eeprom,
.get_ringparam = e1000_get_ringparam,
.set_ringparam = e1000_set_ringparam,
- .get_pauseparam = e1000_get_pauseparam,
- .set_pauseparam = e1000_set_pauseparam,
- .get_rx_csum = e1000_get_rx_csum,
- .set_rx_csum = e1000_set_rx_csum,
- .get_tx_csum = e1000_get_tx_csum,
- .set_tx_csum = e1000_set_tx_csum,
- .get_sg = ethtool_op_get_sg,
- .set_sg = ethtool_op_set_sg,
+ .get_pauseparam = e1000_get_pauseparam,
+ .set_pauseparam = e1000_set_pauseparam,
+ .get_rx_csum = e1000_get_rx_csum,
+ .set_rx_csum = e1000_set_rx_csum,
+ .get_tx_csum = e1000_get_tx_csum,
+ .set_tx_csum = e1000_set_tx_csum,
+ .get_sg = ethtool_op_get_sg,
+ .set_sg = ethtool_op_set_sg,
#ifdef NETIF_F_TSO
- .get_tso = ethtool_op_get_tso,
- .set_tso = e1000_set_tso,
+ .get_tso = ethtool_op_get_tso,
+ .set_tso = e1000_set_tso,
#endif
.self_test_count = e1000_diag_test_count,
.self_test = e1000_diag_test,
@@ -1922,7 +1957,7 @@
.phys_id = e1000_phys_id,
.get_stats_count = e1000_get_stats_count,
.get_ethtool_stats = e1000_get_ethtool_stats,
- .get_perm_addr = ethtool_op_get_perm_addr,
+ .get_perm_addr = ethtool_op_get_perm_addr,
};
void e1000_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index b3b9191..4b54c48 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -31,6 +31,7 @@
* Shared functions for accessing and configuring the MAC
*/
+
#include "e1000_hw.h"
static int32_t e1000_set_phy_type(struct e1000_hw *hw);
@@ -166,10 +167,10 @@
{
DEBUGFUNC("e1000_set_phy_type");
- if(hw->mac_type == e1000_undefined)
+ if (hw->mac_type == e1000_undefined)
return -E1000_ERR_PHY_TYPE;
- switch(hw->phy_id) {
+ switch (hw->phy_id) {
case M88E1000_E_PHY_ID:
case M88E1000_I_PHY_ID:
case M88E1011_I_PHY_ID:
@@ -177,10 +178,10 @@
hw->phy_type = e1000_phy_m88;
break;
case IGP01E1000_I_PHY_ID:
- if(hw->mac_type == e1000_82541 ||
- hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547 ||
- hw->mac_type == e1000_82547_rev_2) {
+ if (hw->mac_type == e1000_82541 ||
+ hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82547_rev_2) {
hw->phy_type = e1000_phy_igp;
break;
}
@@ -207,6 +208,7 @@
return E1000_SUCCESS;
}
+
/******************************************************************************
* IGP phy init script - initializes the GbE PHY
*
@@ -220,7 +222,7 @@
DEBUGFUNC("e1000_phy_init_script");
- if(hw->phy_init_script) {
+ if (hw->phy_init_script) {
msec_delay(20);
/* Save off the current value of register 0x2F5B to be restored at
@@ -236,7 +238,7 @@
msec_delay(5);
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82541:
case e1000_82547:
e1000_write_phy_reg(hw, 0x1F95, 0x0001);
@@ -273,22 +275,22 @@
/* Now enable the transmitter */
e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
- if(hw->mac_type == e1000_82547) {
+ if (hw->mac_type == e1000_82547) {
uint16_t fused, fine, coarse;
/* Move to analog registers page */
e1000_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused);
- if(!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+ if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
e1000_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused);
fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
- if(coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+ if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10;
fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
- } else if(coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+ } else if (coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
@@ -387,6 +389,7 @@
case E1000_DEV_ID_82571EB_COPPER:
case E1000_DEV_ID_82571EB_FIBER:
case E1000_DEV_ID_82571EB_SERDES:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
hw->mac_type = e1000_82571;
break;
case E1000_DEV_ID_82572EI_COPPER:
@@ -418,7 +421,7 @@
return -E1000_ERR_MAC_TYPE;
}
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_ich8lan:
hw->swfwhw_semaphore_present = TRUE;
hw->asf_firmware_present = TRUE;
@@ -456,7 +459,7 @@
DEBUGFUNC("e1000_set_media_type");
- if(hw->mac_type != e1000_82543) {
+ if (hw->mac_type != e1000_82543) {
/* tbi_compatibility is only valid on 82543 */
hw->tbi_compatibility_en = FALSE;
}
@@ -516,16 +519,16 @@
DEBUGFUNC("e1000_reset_hw");
/* For 82542 (rev 2.0), disable MWI before issuing a device reset */
- if(hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->mac_type == e1000_82542_rev2_0) {
DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
e1000_pci_clear_mwi(hw);
}
- if(hw->bus_type == e1000_bus_type_pci_express) {
+ if (hw->bus_type == e1000_bus_type_pci_express) {
/* Prevent the PCI-E bus from sticking if there is no TLP connection
* on the last TLP read/write transaction when MAC is reset.
*/
- if(e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
+ if (e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
DEBUGOUT("PCI-E Master disable polling has failed.\n");
}
}
@@ -553,14 +556,14 @@
ctrl = E1000_READ_REG(hw, CTRL);
/* Must reset the PHY before resetting the MAC */
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST));
msec_delay(5);
}
/* Must acquire the MDIO ownership before MAC reset.
* Ownership defaults to firmware after a reset. */
- if(hw->mac_type == e1000_82573) {
+ if (hw->mac_type == e1000_82573) {
timeout = 10;
extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
@@ -570,14 +573,14 @@
E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl);
extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL);
- if(extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
break;
else
extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
msec_delay(2);
timeout--;
- } while(timeout);
+ } while (timeout);
}
/* Workaround for ICH8 bit corruption issue in FIFO memory */
@@ -595,7 +598,7 @@
*/
DEBUGOUT("Issuing a global reset to MAC\n");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82544:
case e1000_82540:
case e1000_82545:
@@ -634,7 +637,7 @@
* device. Later controllers reload the EEPROM automatically, so just wait
* for reload to complete.
*/
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
case e1000_82543:
@@ -669,7 +672,7 @@
case e1000_ich8lan:
case e1000_80003es2lan:
ret_val = e1000_get_auto_rd_done(hw);
- if(ret_val)
+ if (ret_val)
/* We don't want to continue accessing MAC registers. */
return ret_val;
break;
@@ -680,13 +683,13 @@
}
/* Disable HW ARPs on ASF enabled adapters */
- if(hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
+ if (hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
manc = E1000_READ_REG(hw, MANC);
manc &= ~(E1000_MANC_ARP_EN);
E1000_WRITE_REG(hw, MANC, manc);
}
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
e1000_phy_init_script(hw);
/* Configure activity LED after PHY reset */
@@ -704,8 +707,8 @@
icr = E1000_READ_REG(hw, ICR);
/* If MWI was previously enabled, reenable it. */
- if(hw->mac_type == e1000_82542_rev2_0) {
- if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
e1000_pci_set_mwi(hw);
}
@@ -745,9 +748,20 @@
DEBUGFUNC("e1000_init_hw");
+ /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
+ if (hw->mac_type == e1000_ich8lan) {
+ reg_data = E1000_READ_REG(hw, TARC0);
+ reg_data |= 0x30000000;
+ E1000_WRITE_REG(hw, TARC0, reg_data);
+
+ reg_data = E1000_READ_REG(hw, STATUS);
+ reg_data &= ~0x80000000;
+ E1000_WRITE_REG(hw, STATUS, reg_data);
+ }
+
/* Initialize Identification LED */
ret_val = e1000_id_led_init(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Initializing Identification LED\n");
return ret_val;
}
@@ -765,7 +779,7 @@
}
/* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
- if(hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->mac_type == e1000_82542_rev2_0) {
DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
e1000_pci_clear_mwi(hw);
E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
@@ -779,11 +793,11 @@
e1000_init_rx_addrs(hw);
/* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
- if(hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->mac_type == e1000_82542_rev2_0) {
E1000_WRITE_REG(hw, RCTL, 0);
E1000_WRITE_FLUSH(hw);
msec_delay(1);
- if(hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
+ if (hw->pci_cmd_word & CMD_MEM_WRT_INVALIDATE)
e1000_pci_set_mwi(hw);
}
@@ -792,7 +806,7 @@
mta_size = E1000_MC_TBL_SIZE;
if (hw->mac_type == e1000_ich8lan)
mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
- for(i = 0; i < mta_size; i++) {
+ for (i = 0; i < mta_size; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* use write flush to prevent Memory Write Block (MWB) from
* occuring when accessing our register space */
@@ -804,18 +818,18 @@
* gives equal priority to transmits and receives. Valid only on
* 82542 and 82543 silicon.
*/
- if(hw->dma_fairness && hw->mac_type <= e1000_82543) {
+ if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
ctrl = E1000_READ_REG(hw, CTRL);
E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
}
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82545_rev_3:
case e1000_82546_rev_3:
break;
default:
/* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
- if(hw->bus_type == e1000_bus_type_pcix) {
+ if (hw->bus_type == e1000_bus_type_pcix) {
e1000_read_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
e1000_read_pci_cfg(hw, PCIX_STATUS_REGISTER_HI,
&pcix_stat_hi_word);
@@ -823,9 +837,9 @@
PCIX_COMMAND_MMRBC_SHIFT;
stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
PCIX_STATUS_HI_MMRBC_SHIFT;
- if(stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
+ if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
- if(cmd_mmrbc > stat_mmrbc) {
+ if (cmd_mmrbc > stat_mmrbc) {
pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
e1000_write_pci_cfg(hw, PCIX_COMMAND_REGISTER,
@@ -843,7 +857,7 @@
ret_val = e1000_setup_link(hw);
/* Set the transmit descriptor write-back policy */
- if(hw->mac_type > e1000_82544) {
+ if (hw->mac_type > e1000_82544) {
ctrl = E1000_READ_REG(hw, TXDCTL);
ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
switch (hw->mac_type) {
@@ -894,14 +908,13 @@
case e1000_ich8lan:
ctrl = E1000_READ_REG(hw, TXDCTL1);
ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
- if(hw->mac_type >= e1000_82571)
+ if (hw->mac_type >= e1000_82571)
ctrl |= E1000_TXDCTL_COUNT_DESC;
E1000_WRITE_REG(hw, TXDCTL1, ctrl);
break;
}
-
if (hw->mac_type == e1000_82573) {
uint32_t gcr = E1000_READ_REG(hw, GCR);
gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
@@ -945,10 +958,10 @@
DEBUGFUNC("e1000_adjust_serdes_amplitude");
- if(hw->media_type != e1000_media_type_internal_serdes)
+ if (hw->media_type != e1000_media_type_internal_serdes)
return E1000_SUCCESS;
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82545_rev_3:
case e1000_82546_rev_3:
break;
@@ -961,11 +974,11 @@
return ret_val;
}
- if(eeprom_data != EEPROM_RESERVED_WORD) {
+ if (eeprom_data != EEPROM_RESERVED_WORD) {
/* Adjust SERDES output amplitude only. */
eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -1033,10 +1046,10 @@
* in case we get disconnected and then reconnected into a different
* hub or switch with different Flow Control capabilities.
*/
- if(hw->mac_type == e1000_82542_rev2_0)
+ if (hw->mac_type == e1000_82542_rev2_0)
hw->fc &= (~e1000_fc_tx_pause);
- if((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
+ if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
hw->fc &= (~e1000_fc_rx_pause);
hw->original_fc = hw->fc;
@@ -1051,12 +1064,12 @@
* or e1000_phy_setup() is called.
*/
if (hw->mac_type == e1000_82543) {
- ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
- 1, &eeprom_data);
- if (ret_val) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
SWDPIO__EXT_SHIFT);
E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
@@ -1089,14 +1102,14 @@
* ability to transmit pause frames in not enabled, then these
* registers will be set to 0.
*/
- if(!(hw->fc & e1000_fc_tx_pause)) {
+ if (!(hw->fc & e1000_fc_tx_pause)) {
E1000_WRITE_REG(hw, FCRTL, 0);
E1000_WRITE_REG(hw, FCRTH, 0);
} else {
/* We need to set up the Receive Threshold high and low water marks
* as well as (optionally) enabling the transmission of XON frames.
*/
- if(hw->fc_send_xon) {
+ if (hw->fc_send_xon) {
E1000_WRITE_REG(hw, FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
} else {
@@ -1143,11 +1156,11 @@
* the EEPROM.
*/
ctrl = E1000_READ_REG(hw, CTRL);
- if(hw->media_type == e1000_media_type_fiber)
+ if (hw->media_type == e1000_media_type_fiber)
signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
ret_val = e1000_adjust_serdes_amplitude(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Take the link out of reset */
@@ -1155,7 +1168,7 @@
/* Adjust VCO speed to improve BER performance */
ret_val = e1000_set_vco_speed(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
e1000_config_collision_dist(hw);
@@ -1226,15 +1239,15 @@
* less than 500 milliseconds even if the other end is doing it in SW).
* For internal serdes, we just assume a signal is present, then poll.
*/
- if(hw->media_type == e1000_media_type_internal_serdes ||
+ if (hw->media_type == e1000_media_type_internal_serdes ||
(E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
DEBUGOUT("Looking for Link\n");
- for(i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
+ for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
msec_delay(10);
status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_LU) break;
+ if (status & E1000_STATUS_LU) break;
}
- if(i == (LINK_UP_TIMEOUT / 10)) {
+ if (i == (LINK_UP_TIMEOUT / 10)) {
DEBUGOUT("Never got a valid link from auto-neg!!!\n");
hw->autoneg_failed = 1;
/* AutoNeg failed to achieve a link, so we'll call
@@ -1243,7 +1256,7 @@
* non-autonegotiating link partners.
*/
ret_val = e1000_check_for_link(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error while checking for link\n");
return ret_val;
}
@@ -1277,7 +1290,7 @@
* the PHY speed and duplex configuration is. In addition, we need to
* perform a hardware reset on the PHY to take it out of reset.
*/
- if(hw->mac_type > e1000_82543) {
+ if (hw->mac_type > e1000_82543) {
ctrl |= E1000_CTRL_SLU;
ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
E1000_WRITE_REG(hw, CTRL, ctrl);
@@ -1285,13 +1298,13 @@
ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
E1000_WRITE_REG(hw, CTRL, ctrl);
ret_val = e1000_phy_hw_reset(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
/* Make sure we have a valid PHY */
ret_val = e1000_detect_gig_phy(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error, did not detect valid phy.\n");
return ret_val;
}
@@ -1299,19 +1312,19 @@
/* Set PHY to class A mode (if necessary) */
ret_val = e1000_set_phy_mode(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if((hw->mac_type == e1000_82545_rev_3) ||
+ if ((hw->mac_type == e1000_82545_rev_3) ||
(hw->mac_type == e1000_82546_rev_3)) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
phy_data |= 0x00000008;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
}
- if(hw->mac_type <= e1000_82543 ||
- hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
- hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
+ if (hw->mac_type <= e1000_82543 ||
+ hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
hw->phy_reset_disable = FALSE;
return E1000_SUCCESS;
@@ -1341,7 +1354,7 @@
return ret_val;
}
- /* Wait 10ms for MAC to configure PHY from eeprom settings */
+ /* Wait 15ms for MAC to configure PHY from eeprom settings */
msec_delay(15);
if (hw->mac_type != e1000_ich8lan) {
/* Configure activity LED after PHY reset */
@@ -1351,11 +1364,14 @@
E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
}
- /* disable lplu d3 during driver init */
- ret_val = e1000_set_d3_lplu_state(hw, FALSE);
- if (ret_val) {
- DEBUGOUT("Error Disabling LPLU D3\n");
- return ret_val;
+ /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
+ if (hw->phy_type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, FALSE);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
}
/* disable lplu d0 during driver init */
@@ -1393,45 +1409,45 @@
}
}
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* set auto-master slave resolution settings */
- if(hw->autoneg) {
+ if (hw->autoneg) {
e1000_ms_type phy_ms_setting = hw->master_slave;
- if(hw->ffe_config_state == e1000_ffe_config_active)
+ if (hw->ffe_config_state == e1000_ffe_config_active)
hw->ffe_config_state = e1000_ffe_config_enabled;
- if(hw->dsp_config_state == e1000_dsp_config_activated)
+ if (hw->dsp_config_state == e1000_dsp_config_activated)
hw->dsp_config_state = e1000_dsp_config_enabled;
/* when autonegotiation advertisment is only 1000Mbps then we
* should disable SmartSpeed and enable Auto MasterSlave
* resolution as hardware default. */
- if(hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
/* Disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if(ret_val)
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw,
- IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if(ret_val)
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
return ret_val;
/* Set auto Master/Slave resolution process */
ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~CR_1000T_MS_ENABLE;
ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* load defaults for future use */
@@ -1455,7 +1471,7 @@
break;
}
ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -1476,12 +1492,12 @@
DEBUGFUNC("e1000_copper_link_ggp_setup");
- if(!hw->phy_reset_disable) {
+ if (!hw->phy_reset_disable) {
/* Enable CRS on TX for half-duplex operation. */
ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
@@ -1490,7 +1506,7 @@
ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Options:
@@ -1501,7 +1517,7 @@
* 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
*/
ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
@@ -1526,11 +1542,11 @@
* 1 - Enabled
*/
phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
- if(hw->disable_polarity_correction == 1)
+ if (hw->disable_polarity_correction == 1)
phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* SW Reset the PHY so all changes take effect */
@@ -1586,9 +1602,9 @@
return ret_val;
phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
-
ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
phy_data);
+
if (ret_val)
return ret_val;
}
@@ -1623,12 +1639,12 @@
DEBUGFUNC("e1000_copper_link_mgp_setup");
- if(hw->phy_reset_disable)
+ if (hw->phy_reset_disable)
return E1000_SUCCESS;
/* Enable CRS on TX. This must be set for half-duplex operation. */
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
@@ -1665,7 +1681,7 @@
* 1 - Enabled
*/
phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if(hw->disable_polarity_correction == 1)
+ if (hw->disable_polarity_correction == 1)
phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
if (ret_val)
@@ -1705,7 +1721,7 @@
/* SW Reset the PHY so all changes take effect */
ret_val = e1000_phy_reset(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Resetting the PHY\n");
return ret_val;
}
@@ -1735,7 +1751,7 @@
/* If autoneg_advertised is zero, we assume it was not defaulted
* by the calling code so we set to advertise full capability.
*/
- if(hw->autoneg_advertised == 0)
+ if (hw->autoneg_advertised == 0)
hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
/* IFE phy only supports 10/100 */
@@ -1744,7 +1760,7 @@
DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
ret_val = e1000_phy_setup_autoneg(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Setting up Auto-Negotiation\n");
return ret_val;
}
@@ -1754,20 +1770,20 @@
* the Auto Neg Restart bit in the PHY control register.
*/
ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Does the user want to wait for Auto-Neg to complete here, or
* check at a later time (for example, callback routine).
*/
- if(hw->wait_autoneg_complete) {
+ if (hw->wait_autoneg_complete) {
ret_val = e1000_wait_autoneg(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error while waiting for autoneg to complete\n");
return ret_val;
}
@@ -1778,7 +1794,6 @@
return E1000_SUCCESS;
}
-
/******************************************************************************
* Config the MAC and the PHY after link is up.
* 1) Set up the MAC to the current PHY speed/duplex
@@ -1797,25 +1812,25 @@
int32_t ret_val;
DEBUGFUNC("e1000_copper_link_postconfig");
- if(hw->mac_type >= e1000_82544) {
+ if (hw->mac_type >= e1000_82544) {
e1000_config_collision_dist(hw);
} else {
ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error configuring MAC to PHY settings\n");
return ret_val;
}
}
ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Configuring Flow Control\n");
return ret_val;
}
/* Config DSP to improve Giga link quality */
- if(hw->phy_type == e1000_phy_igp) {
+ if (hw->phy_type == e1000_phy_igp) {
ret_val = e1000_config_dsp_after_link_change(hw, TRUE);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Configuring DSP after link up\n");
return ret_val;
}
@@ -1861,7 +1876,7 @@
/* Check if it is a valid PHY and set PHY mode if necessary. */
ret_val = e1000_copper_link_preconfig(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
switch (hw->mac_type) {
@@ -1882,30 +1897,30 @@
hw->phy_type == e1000_phy_igp_3 ||
hw->phy_type == e1000_phy_igp_2) {
ret_val = e1000_copper_link_igp_setup(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else if (hw->phy_type == e1000_phy_m88) {
ret_val = e1000_copper_link_mgp_setup(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else if (hw->phy_type == e1000_phy_gg82563) {
ret_val = e1000_copper_link_ggp_setup(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
- if(hw->autoneg) {
+ if (hw->autoneg) {
/* Setup autoneg and flow control advertisement
* and perform autonegotiation */
ret_val = e1000_copper_link_autoneg(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else {
/* PHY will be set to 10H, 10F, 100H,or 100F
* depending on value from forced_speed_duplex. */
DEBUGOUT("Forcing speed and duplex\n");
ret_val = e1000_phy_force_speed_duplex(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Forcing Speed and Duplex\n");
return ret_val;
}
@@ -1914,18 +1929,18 @@
/* Check link status. Wait up to 100 microseconds for link to become
* valid.
*/
- for(i = 0; i < 10; i++) {
+ for (i = 0; i < 10; i++) {
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(phy_data & MII_SR_LINK_STATUS) {
+ if (phy_data & MII_SR_LINK_STATUS) {
/* Config the MAC and PHY after link is up */
ret_val = e1000_copper_link_postconfig(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
DEBUGOUT("Valid link established!!!\n");
@@ -2027,7 +2042,7 @@
/* Read the MII Auto-Neg Advertisement Register (Address 4). */
ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
if (hw->phy_type != e1000_phy_ife) {
@@ -2055,36 +2070,36 @@
DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
/* Do we want to advertise 10 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
DEBUGOUT("Advertise 10mb Half duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
}
/* Do we want to advertise 10 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_10_FULL) {
+ if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
DEBUGOUT("Advertise 10mb Full duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
}
/* Do we want to advertise 100 Mb Half Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_HALF) {
+ if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
DEBUGOUT("Advertise 100mb Half duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
}
/* Do we want to advertise 100 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_100_FULL) {
+ if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
DEBUGOUT("Advertise 100mb Full duplex\n");
mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
}
/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
- if(hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+ if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
}
/* Do we want to advertise 1000 Mb Full Duplex? */
- if(hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+ if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
DEBUGOUT("Advertise 1000mb Full duplex\n");
mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
if (hw->phy_type == e1000_phy_ife) {
@@ -2146,7 +2161,7 @@
}
ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
@@ -2194,7 +2209,7 @@
/* Read the MII Control Register. */
ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* We need to disable autoneg in order to force link and duplex. */
@@ -2202,8 +2217,8 @@
mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
/* Are we forcing Full or Half Duplex? */
- if(hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_10_full) {
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_10_full) {
/* We want to force full duplex so we SET the full duplex bits in the
* Device and MII Control Registers.
*/
@@ -2220,7 +2235,7 @@
}
/* Are we forcing 100Mbps??? */
- if(hw->forced_speed_duplex == e1000_100_full ||
+ if (hw->forced_speed_duplex == e1000_100_full ||
hw->forced_speed_duplex == e1000_100_half) {
/* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
ctrl |= E1000_CTRL_SPD_100;
@@ -2243,7 +2258,7 @@
if ((hw->phy_type == e1000_phy_m88) ||
(hw->phy_type == e1000_phy_gg82563)) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
@@ -2251,7 +2266,7 @@
*/
phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
@@ -2275,20 +2290,20 @@
* forced whenever speed or duplex are forced.
*/
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
/* Write back the modified PHY MII control register. */
ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
udelay(1);
@@ -2300,50 +2315,50 @@
* only if the user has set wait_autoneg_complete to 1, which is
* the default.
*/
- if(hw->wait_autoneg_complete) {
+ if (hw->wait_autoneg_complete) {
/* We will wait for autoneg to complete. */
DEBUGOUT("Waiting for forced speed/duplex link.\n");
mii_status_reg = 0;
/* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
/* Read the MII Status Register and wait for Auto-Neg Complete bit
* to be set.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ if (mii_status_reg & MII_SR_LINK_STATUS) break;
msec_delay(100);
}
- if((i == 0) &&
+ if ((i == 0) &&
((hw->phy_type == e1000_phy_m88) ||
(hw->phy_type == e1000_phy_gg82563))) {
/* We didn't get link. Reset the DSP and wait again for link. */
ret_val = e1000_phy_reset_dsp(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error Resetting PHY DSP\n");
return ret_val;
}
}
/* This loop will early-out if the link condition has been met. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ if (mii_status_reg & MII_SR_LINK_STATUS) break;
msec_delay(100);
/* Read the MII Status Register and wait for Auto-Neg Complete bit
* to be set.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
}
@@ -2354,32 +2369,31 @@
* defaults back to a 2.5MHz clock when the PHY is reset.
*/
ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= M88E1000_EPSCR_TX_CLK_25;
ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* In addition, because of the s/w reset above, we need to enable CRS on
* TX. This must be set for both full and half duplex operation.
*/
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
- (!hw->autoneg) &&
- (hw->forced_speed_duplex == e1000_10_full ||
- hw->forced_speed_duplex == e1000_10_half)) {
+ if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
+ (!hw->autoneg) && (hw->forced_speed_duplex == e1000_10_full ||
+ hw->forced_speed_duplex == e1000_10_half)) {
ret_val = e1000_polarity_reversal_workaround(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
} else if (hw->phy_type == e1000_phy_gg82563) {
@@ -2470,10 +2484,10 @@
* registers depending on negotiated values.
*/
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(phy_data & M88E1000_PSSR_DPLX)
+ if (phy_data & M88E1000_PSSR_DPLX)
ctrl |= E1000_CTRL_FD;
else
ctrl &= ~E1000_CTRL_FD;
@@ -2483,9 +2497,9 @@
/* Set up speed in the Device Control register depending on
* negotiated values.
*/
- if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
ctrl |= E1000_CTRL_SPD_1000;
- else if((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
ctrl |= E1000_CTRL_SPD_100;
/* Write the configured values back to the Device Control Reg. */
@@ -2553,7 +2567,7 @@
}
/* Disable TX Flow Control for 82542 (rev 2.0) */
- if(hw->mac_type == e1000_82542_rev2_0)
+ if (hw->mac_type == e1000_82542_rev2_0)
ctrl &= (~E1000_CTRL_TFCE);
E1000_WRITE_REG(hw, CTRL, ctrl);
@@ -2587,11 +2601,12 @@
* so we had to force link. In this case, we need to force the
* configuration of the MAC to match the "fc" parameter.
*/
- if(((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_internal_serdes) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
+ if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
+ ((hw->media_type == e1000_media_type_internal_serdes) &&
+ (hw->autoneg_failed)) ||
+ ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
ret_val = e1000_force_mac_fc(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error forcing flow control settings\n");
return ret_val;
}
@@ -2602,19 +2617,19 @@
* has completed, and if so, how the PHY and link partner has
* flow control configured.
*/
- if((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
+ if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
/* Read the MII Status Register and check to see if AutoNeg
* has completed. We read this twice because this reg has
* some "sticky" (latched) bits.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+ if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
/* The AutoNeg process has completed, so we now need to
* read both the Auto Negotiation Advertisement Register
* (Address 4) and the Auto_Negotiation Base Page Ability
@@ -2623,11 +2638,11 @@
*/
ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
&mii_nway_adv_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
&mii_nway_lp_ability_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Two bits in the Auto Negotiation Advertisement Register
@@ -2664,15 +2679,15 @@
* 1 | DC | 1 | DC | e1000_fc_full
*
*/
- if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
/* Now we need to check if the user selected RX ONLY
* of pause frames. In this case, we had to advertise
* FULL flow control because we could not advertise RX
* ONLY. Hence, we must now check to see if we need to
* turn OFF the TRANSMISSION of PAUSE frames.
*/
- if(hw->original_fc == e1000_fc_full) {
+ if (hw->original_fc == e1000_fc_full) {
hw->fc = e1000_fc_full;
DEBUGOUT("Flow Control = FULL.\n");
} else {
@@ -2688,10 +2703,10 @@
* 0 | 1 | 1 | 1 | e1000_fc_tx_pause
*
*/
- else if(!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
hw->fc = e1000_fc_tx_pause;
DEBUGOUT("Flow Control = TX PAUSE frames only.\n");
}
@@ -2703,10 +2718,10 @@
* 1 | 1 | 0 | 1 | e1000_fc_rx_pause
*
*/
- else if((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
hw->fc = e1000_fc_rx_pause;
DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
}
@@ -2730,9 +2745,9 @@
* be asked to delay transmission of packets than asking
* our link partner to pause transmission of frames.
*/
- else if((hw->original_fc == e1000_fc_none ||
- hw->original_fc == e1000_fc_tx_pause) ||
- hw->fc_strict_ieee) {
+ else if ((hw->original_fc == e1000_fc_none ||
+ hw->original_fc == e1000_fc_tx_pause) ||
+ hw->fc_strict_ieee) {
hw->fc = e1000_fc_none;
DEBUGOUT("Flow Control = NONE.\n");
} else {
@@ -2745,19 +2760,19 @@
* enabled per IEEE 802.3 spec.
*/
ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error getting link speed and duplex\n");
return ret_val;
}
- if(duplex == HALF_DUPLEX)
+ if (duplex == HALF_DUPLEX)
hw->fc = e1000_fc_none;
/* Now we call a subroutine to actually force the MAC
* controller to use the correct flow control settings.
*/
ret_val = e1000_force_mac_fc(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error forcing flow control settings\n");
return ret_val;
}
@@ -2796,13 +2811,13 @@
* set when the optics detect a signal. On older adapters, it will be
* cleared when there is a signal. This applies to fiber media only.
*/
- if((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) {
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) {
rxcw = E1000_READ_REG(hw, RXCW);
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
- if(status & E1000_STATUS_LU)
+ if (status & E1000_STATUS_LU)
hw->get_link_status = FALSE;
}
}
@@ -2813,20 +2828,20 @@
* receive a Link Status Change interrupt or we have Rx Sequence
* Errors.
*/
- if((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+ if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
/* First we want to see if the MII Status Register reports
* link. If so, then we want to get the current speed/duplex
* of the PHY.
* Read the register twice since the link bit is sticky.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(phy_data & MII_SR_LINK_STATUS) {
+ if (phy_data & MII_SR_LINK_STATUS) {
hw->get_link_status = FALSE;
/* Check if there was DownShift, must be checked immediately after
* link-up */
@@ -2840,10 +2855,10 @@
* happen due to the execution of this workaround.
*/
- if((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
- (!hw->autoneg) &&
- (hw->forced_speed_duplex == e1000_10_full ||
- hw->forced_speed_duplex == e1000_10_half)) {
+ if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
+ (!hw->autoneg) &&
+ (hw->forced_speed_duplex == e1000_10_full ||
+ hw->forced_speed_duplex == e1000_10_half)) {
E1000_WRITE_REG(hw, IMC, 0xffffffff);
ret_val = e1000_polarity_reversal_workaround(hw);
icr = E1000_READ_REG(hw, ICR);
@@ -2860,7 +2875,7 @@
/* If we are forcing speed/duplex, then we simply return since
* we have already determined whether we have link or not.
*/
- if(!hw->autoneg) return -E1000_ERR_CONFIG;
+ if (!hw->autoneg) return -E1000_ERR_CONFIG;
/* optimize the dsp settings for the igp phy */
e1000_config_dsp_after_link_change(hw, TRUE);
@@ -2873,11 +2888,11 @@
* speed/duplex on the MAC to the current PHY speed/duplex
* settings.
*/
- if(hw->mac_type >= e1000_82544)
+ if (hw->mac_type >= e1000_82544)
e1000_config_collision_dist(hw);
else {
ret_val = e1000_config_mac_to_phy(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error configuring MAC to PHY settings\n");
return ret_val;
}
@@ -2888,7 +2903,7 @@
* have had to re-autoneg with a different link partner.
*/
ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error configuring flow control\n");
return ret_val;
}
@@ -2900,7 +2915,7 @@
* at gigabit speed, then TBI compatibility is not needed. If we are
* at gigabit speed, we turn on TBI compatibility.
*/
- if(hw->tbi_compatibility_en) {
+ if (hw->tbi_compatibility_en) {
uint16_t speed, duplex;
ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
if (ret_val) {
@@ -2911,7 +2926,7 @@
/* If link speed is not set to gigabit speed, we do not need
* to enable TBI compatibility.
*/
- if(hw->tbi_compatibility_on) {
+ if (hw->tbi_compatibility_on) {
/* If we previously were in the mode, turn it off. */
rctl = E1000_READ_REG(hw, RCTL);
rctl &= ~E1000_RCTL_SBP;
@@ -2924,7 +2939,7 @@
* packets. Some frames have an additional byte on the end and
* will look like CRC errors to to the hardware.
*/
- if(!hw->tbi_compatibility_on) {
+ if (!hw->tbi_compatibility_on) {
hw->tbi_compatibility_on = TRUE;
rctl = E1000_READ_REG(hw, RCTL);
rctl |= E1000_RCTL_SBP;
@@ -2940,12 +2955,12 @@
* auto-negotiation time to complete, in case the cable was just plugged
* in. The autoneg_failed flag does this.
*/
- else if((((hw->media_type == e1000_media_type_fiber) &&
+ else if ((((hw->media_type == e1000_media_type_fiber) &&
((ctrl & E1000_CTRL_SWDPIN1) == signal)) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (!(status & E1000_STATUS_LU)) &&
- (!(rxcw & E1000_RXCW_C))) {
- if(hw->autoneg_failed == 0) {
+ (hw->media_type == e1000_media_type_internal_serdes)) &&
+ (!(status & E1000_STATUS_LU)) &&
+ (!(rxcw & E1000_RXCW_C))) {
+ if (hw->autoneg_failed == 0) {
hw->autoneg_failed = 1;
return 0;
}
@@ -2961,7 +2976,7 @@
/* Configure Flow Control after forcing link up. */
ret_val = e1000_config_fc_after_link_up(hw);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error configuring flow control\n");
return ret_val;
}
@@ -2971,9 +2986,9 @@
* Device Control register in an attempt to auto-negotiate with our link
* partner.
*/
- else if(((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ else if (((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) &&
+ (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
E1000_WRITE_REG(hw, TXCW, hw->txcw);
E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
@@ -2983,12 +2998,12 @@
/* If we force link for non-auto-negotiation switch, check link status
* based on MAC synchronization for internal serdes media type.
*/
- else if((hw->media_type == e1000_media_type_internal_serdes) &&
- !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
+ else if ((hw->media_type == e1000_media_type_internal_serdes) &&
+ !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
/* SYNCH bit and IV bit are sticky. */
udelay(10);
- if(E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
- if(!(rxcw & E1000_RXCW_IV)) {
+ if (E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) {
+ if (!(rxcw & E1000_RXCW_IV)) {
hw->serdes_link_down = FALSE;
DEBUGOUT("SERDES: Link is up.\n");
}
@@ -2997,8 +3012,8 @@
DEBUGOUT("SERDES: Link is down.\n");
}
}
- if((hw->media_type == e1000_media_type_internal_serdes) &&
- (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
+ if ((hw->media_type == e1000_media_type_internal_serdes) &&
+ (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) {
hw->serdes_link_down = !(E1000_STATUS_LU & E1000_READ_REG(hw, STATUS));
}
return E1000_SUCCESS;
@@ -3022,12 +3037,12 @@
DEBUGFUNC("e1000_get_speed_and_duplex");
- if(hw->mac_type >= e1000_82543) {
+ if (hw->mac_type >= e1000_82543) {
status = E1000_READ_REG(hw, STATUS);
- if(status & E1000_STATUS_SPEED_1000) {
+ if (status & E1000_STATUS_SPEED_1000) {
*speed = SPEED_1000;
DEBUGOUT("1000 Mbs, ");
- } else if(status & E1000_STATUS_SPEED_100) {
+ } else if (status & E1000_STATUS_SPEED_100) {
*speed = SPEED_100;
DEBUGOUT("100 Mbs, ");
} else {
@@ -3035,7 +3050,7 @@
DEBUGOUT("10 Mbs, ");
}
- if(status & E1000_STATUS_FD) {
+ if (status & E1000_STATUS_FD) {
*duplex = FULL_DUPLEX;
DEBUGOUT("Full Duplex\n");
} else {
@@ -3052,18 +3067,18 @@
* if it is operating at half duplex. Here we set the duplex settings to
* match the duplex in the link partner's capabilities.
*/
- if(hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
*duplex = HALF_DUPLEX;
else {
ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) ||
+ if ((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) ||
(*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
*duplex = HALF_DUPLEX;
}
@@ -3104,17 +3119,17 @@
DEBUGOUT("Waiting for Auto-Neg to complete.\n");
/* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for(i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+ for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
/* Read the MII Status Register and wait for Auto-Neg
* Complete bit to be set.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(phy_data & MII_SR_AUTONEG_COMPLETE) {
+ if (phy_data & MII_SR_AUTONEG_COMPLETE) {
return E1000_SUCCESS;
}
msec_delay(100);
@@ -3187,14 +3202,16 @@
/* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
- while(mask) {
+ while (mask) {
/* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
* then raising and lowering the Management Data Clock. A "0" is
* shifted out to the PHY by setting the MDIO bit to "0" and then
* raising and lowering the clock.
*/
- if(data & mask) ctrl |= E1000_CTRL_MDIO;
- else ctrl &= ~E1000_CTRL_MDIO;
+ if (data & mask)
+ ctrl |= E1000_CTRL_MDIO;
+ else
+ ctrl &= ~E1000_CTRL_MDIO;
E1000_WRITE_REG(hw, CTRL, ctrl);
E1000_WRITE_FLUSH(hw);
@@ -3245,12 +3262,13 @@
e1000_raise_mdi_clk(hw, &ctrl);
e1000_lower_mdi_clk(hw, &ctrl);
- for(data = 0, i = 0; i < 16; i++) {
+ for (data = 0, i = 0; i < 16; i++) {
data = data << 1;
e1000_raise_mdi_clk(hw, &ctrl);
ctrl = E1000_READ_REG(hw, CTRL);
/* Check to see if we shifted in a "1". */
- if(ctrl & E1000_CTRL_MDIO) data |= 1;
+ if (ctrl & E1000_CTRL_MDIO)
+ data |= 1;
e1000_lower_mdi_clk(hw, &ctrl);
}
@@ -3276,7 +3294,7 @@
if (!hw->swfw_sync_present)
return e1000_get_hw_eeprom_semaphore(hw);
- while(timeout) {
+ while (timeout) {
if (e1000_get_hw_eeprom_semaphore(hw))
return -E1000_ERR_SWFW_SYNC;
@@ -3365,7 +3383,7 @@
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(uint16_t)reg_addr);
- if(ret_val) {
+ if (ret_val) {
e1000_swfw_sync_release(hw, swfw);
return ret_val;
}
@@ -3410,12 +3428,12 @@
DEBUGFUNC("e1000_read_phy_reg_ex");
- if(reg_addr > MAX_PHY_REG_ADDRESS) {
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
return -E1000_ERR_PARAM;
}
- if(hw->mac_type > e1000_82543) {
+ if (hw->mac_type > e1000_82543) {
/* Set up Op-code, Phy Address, and register address in the MDI
* Control register. The MAC will take care of interfacing with the
* PHY to retrieve the desired data.
@@ -3427,16 +3445,16 @@
E1000_WRITE_REG(hw, MDIC, mdic);
/* Poll the ready bit to see if the MDI read completed */
- for(i = 0; i < 64; i++) {
+ for (i = 0; i < 64; i++) {
udelay(50);
mdic = E1000_READ_REG(hw, MDIC);
- if(mdic & E1000_MDIC_READY) break;
+ if (mdic & E1000_MDIC_READY) break;
}
- if(!(mdic & E1000_MDIC_READY)) {
+ if (!(mdic & E1000_MDIC_READY)) {
DEBUGOUT("MDI Read did not complete\n");
return -E1000_ERR_PHY;
}
- if(mdic & E1000_MDIC_ERROR) {
+ if (mdic & E1000_MDIC_ERROR) {
DEBUGOUT("MDI Error\n");
return -E1000_ERR_PHY;
}
@@ -3505,7 +3523,7 @@
(reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
(uint16_t)reg_addr);
- if(ret_val) {
+ if (ret_val) {
e1000_swfw_sync_release(hw, swfw);
return ret_val;
}
@@ -3550,12 +3568,12 @@
DEBUGFUNC("e1000_write_phy_reg_ex");
- if(reg_addr > MAX_PHY_REG_ADDRESS) {
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
return -E1000_ERR_PARAM;
}
- if(hw->mac_type > e1000_82543) {
+ if (hw->mac_type > e1000_82543) {
/* Set up Op-code, Phy Address, register address, and data intended
* for the PHY register in the MDI Control register. The MAC will take
* care of interfacing with the PHY to send the desired data.
@@ -3568,12 +3586,12 @@
E1000_WRITE_REG(hw, MDIC, mdic);
/* Poll the ready bit to see if the MDI read completed */
- for(i = 0; i < 640; i++) {
+ for (i = 0; i < 641; i++) {
udelay(5);
mdic = E1000_READ_REG(hw, MDIC);
- if(mdic & E1000_MDIC_READY) break;
+ if (mdic & E1000_MDIC_READY) break;
}
- if(!(mdic & E1000_MDIC_READY)) {
+ if (!(mdic & E1000_MDIC_READY)) {
DEBUGOUT("MDI Write did not complete\n");
return -E1000_ERR_PHY;
}
@@ -3685,7 +3703,7 @@
DEBUGOUT("Resetting Phy...\n");
- if(hw->mac_type > e1000_82543) {
+ if (hw->mac_type > e1000_82543) {
if ((hw->mac_type == e1000_80003es2lan) &&
(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
swfw = E1000_SWFW_PHY1_SM;
@@ -3733,7 +3751,7 @@
}
udelay(150);
- if((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
/* Configure activity LED after PHY reset */
led_ctrl = E1000_READ_REG(hw, LEDCTL);
led_ctrl &= IGP_ACTIVITY_LED_MASK;
@@ -3743,14 +3761,13 @@
/* Wait for FW to finish PHY configuration. */
ret_val = e1000_get_phy_cfg_done(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
e1000_release_software_semaphore(hw);
- if ((hw->mac_type == e1000_ich8lan) &&
- (hw->phy_type == e1000_phy_igp_3)) {
- ret_val = e1000_init_lcd_from_nvm(hw);
- if (ret_val)
- return ret_val;
- }
+ if ((hw->mac_type == e1000_ich8lan) && (hw->phy_type == e1000_phy_igp_3))
+ ret_val = e1000_init_lcd_from_nvm(hw);
+
return ret_val;
}
@@ -3781,25 +3798,25 @@
case e1000_82572:
case e1000_ich8lan:
ret_val = e1000_phy_hw_reset(hw);
- if(ret_val)
+ if (ret_val)
return ret_val;
break;
default:
ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= MII_CR_RESET;
ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
udelay(1);
break;
}
- if(hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
+ if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
e1000_phy_init_script(hw);
return E1000_SUCCESS;
@@ -3877,8 +3894,8 @@
if (hw->kmrn_lock_loss_workaround_disabled)
return E1000_SUCCESS;
- /* Make sure link is up before proceeding. If not just return.
- * Attempting this while link is negotiating fouls up link
+ /* Make sure link is up before proceeding. If not just return.
+ * Attempting this while link is negotiating fouled up link
* stability */
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
@@ -3955,34 +3972,34 @@
hw->phy_id = (uint32_t) (phy_id_high << 16);
udelay(20);
ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK);
hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK;
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82543:
- if(hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
+ if (hw->phy_id == M88E1000_E_PHY_ID) match = TRUE;
break;
case e1000_82544:
- if(hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
+ if (hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
break;
case e1000_82540:
case e1000_82545:
case e1000_82545_rev_3:
case e1000_82546:
case e1000_82546_rev_3:
- if(hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
+ if (hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
break;
case e1000_82541:
case e1000_82541_rev_2:
case e1000_82547:
case e1000_82547_rev_2:
- if(hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
+ if (hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE;
break;
case e1000_82573:
- if(hw->phy_id == M88E1111_I_PHY_ID) match = TRUE;
+ if (hw->phy_id == M88E1111_I_PHY_ID) match = TRUE;
break;
case e1000_80003es2lan:
if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE;
@@ -4021,14 +4038,14 @@
do {
if (hw->phy_type != e1000_phy_gg82563) {
ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
- if(ret_val) break;
+ if (ret_val) break;
}
ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
- if(ret_val) break;
+ if (ret_val) break;
ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
- if(ret_val) break;
+ if (ret_val) break;
ret_val = E1000_SUCCESS;
- } while(0);
+ } while (0);
return ret_val;
}
@@ -4039,7 +4056,7 @@
* hw - Struct containing variables accessed by shared code
* phy_info - PHY information structure
******************************************************************************/
-static int32_t
+int32_t
e1000_phy_igp_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info)
{
@@ -4060,23 +4077,23 @@
/* Check polarity status */
ret_val = e1000_check_polarity(hw, &polarity);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->cable_polarity = polarity;
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->mdix_mode = (phy_data & IGP01E1000_PSSR_MDIX) >>
IGP01E1000_PSSR_MDIX_SHIFT;
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
IGP01E1000_PSSR_SPEED_1000MBPS) {
/* Local/Remote Receiver Information are only valid at 1000 Mbps */
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
@@ -4086,19 +4103,19 @@
/* Get cable length */
ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Translate to old method */
average = (max_length + min_length) / 2;
- if(average <= e1000_igp_cable_length_50)
+ if (average <= e1000_igp_cable_length_50)
phy_info->cable_length = e1000_cable_length_50;
- else if(average <= e1000_igp_cable_length_80)
+ else if (average <= e1000_igp_cable_length_80)
phy_info->cable_length = e1000_cable_length_50_80;
- else if(average <= e1000_igp_cable_length_110)
+ else if (average <= e1000_igp_cable_length_110)
phy_info->cable_length = e1000_cable_length_80_110;
- else if(average <= e1000_igp_cable_length_140)
+ else if (average <= e1000_igp_cable_length_140)
phy_info->cable_length = e1000_cable_length_110_140;
else
phy_info->cable_length = e1000_cable_length_140;
@@ -4174,7 +4191,7 @@
phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->extended_10bt_distance =
@@ -4186,12 +4203,12 @@
/* Check polarity status */
ret_val = e1000_check_polarity(hw, &polarity);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->cable_polarity = polarity;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->mdix_mode = (phy_data & M88E1000_PSSR_MDIX) >>
@@ -4214,7 +4231,7 @@
}
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_info->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS) >>
@@ -4251,20 +4268,20 @@
phy_info->local_rx = e1000_1000t_rx_status_undefined;
phy_info->remote_rx = e1000_1000t_rx_status_undefined;
- if(hw->media_type != e1000_media_type_copper) {
+ if (hw->media_type != e1000_media_type_copper) {
DEBUGOUT("PHY info is only valid for copper media\n");
return -E1000_ERR_CONFIG;
}
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
+ if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
DEBUGOUT("PHY info is only valid if link is up\n");
return -E1000_ERR_CONFIG;
}
@@ -4284,7 +4301,7 @@
{
DEBUGFUNC("e1000_validate_mdi_settings");
- if(!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
+ if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
DEBUGOUT("Invalid MDI setting detected\n");
hw->mdix = 1;
return -E1000_ERR_CONFIG;
@@ -4331,7 +4348,7 @@
eeprom->type = e1000_eeprom_microwire;
eeprom->opcode_bits = 3;
eeprom->delay_usec = 50;
- if(eecd & E1000_EECD_SIZE) {
+ if (eecd & E1000_EECD_SIZE) {
eeprom->word_size = 256;
eeprom->address_bits = 8;
} else {
@@ -4399,7 +4416,7 @@
}
eeprom->use_eerd = TRUE;
eeprom->use_eewr = TRUE;
- if(e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
+ if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) {
eeprom->type = e1000_eeprom_flash;
eeprom->word_size = 2048;
@@ -4460,17 +4477,17 @@
/* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
* 32KB (incremented by powers of 2).
*/
- if(hw->mac_type <= e1000_82547_rev_2) {
+ if (hw->mac_type <= e1000_82547_rev_2) {
/* Set to default value for initial eeprom read. */
eeprom->word_size = 64;
ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
- if(ret_val)
+ if (ret_val)
return ret_val;
eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
/* 256B eeprom size was not supported in earlier hardware, so we
* bump eeprom_size up one to ensure that "1" (which maps to 256B)
* is never the result used in the shifting logic below. */
- if(eeprom_size)
+ if (eeprom_size)
eeprom_size++;
} else {
eeprom_size = (uint16_t)((eecd & E1000_EECD_SIZE_EX_MASK) >>
@@ -4555,7 +4572,7 @@
*/
eecd &= ~E1000_EECD_DI;
- if(data & mask)
+ if (data & mask)
eecd |= E1000_EECD_DI;
E1000_WRITE_REG(hw, EECD, eecd);
@@ -4568,7 +4585,7 @@
mask = mask >> 1;
- } while(mask);
+ } while (mask);
/* We leave the "DI" bit set to "0" when we leave this routine. */
eecd &= ~E1000_EECD_DI;
@@ -4600,14 +4617,14 @@
eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
data = 0;
- for(i = 0; i < count; i++) {
+ for (i = 0; i < count; i++) {
data = data << 1;
e1000_raise_ee_clk(hw, &eecd);
eecd = E1000_READ_REG(hw, EECD);
eecd &= ~(E1000_EECD_DI);
- if(eecd & E1000_EECD_DO)
+ if (eecd & E1000_EECD_DO)
data |= 1;
e1000_lower_ee_clk(hw, &eecd);
@@ -4638,17 +4655,17 @@
if (hw->mac_type != e1000_82573) {
/* Request EEPROM Access */
- if(hw->mac_type > e1000_82544) {
+ if (hw->mac_type > e1000_82544) {
eecd |= E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
eecd = E1000_READ_REG(hw, EECD);
- while((!(eecd & E1000_EECD_GNT)) &&
+ while ((!(eecd & E1000_EECD_GNT)) &&
(i < E1000_EEPROM_GRANT_ATTEMPTS)) {
i++;
udelay(5);
eecd = E1000_READ_REG(hw, EECD);
}
- if(!(eecd & E1000_EECD_GNT)) {
+ if (!(eecd & E1000_EECD_GNT)) {
eecd &= ~E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
DEBUGOUT("Could not acquire EEPROM grant\n");
@@ -4691,7 +4708,7 @@
eecd = E1000_READ_REG(hw, EECD);
- if(eeprom->type == e1000_eeprom_microwire) {
+ if (eeprom->type == e1000_eeprom_microwire) {
eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
E1000_WRITE_REG(hw, EECD, eecd);
E1000_WRITE_FLUSH(hw);
@@ -4714,7 +4731,7 @@
E1000_WRITE_REG(hw, EECD, eecd);
E1000_WRITE_FLUSH(hw);
udelay(eeprom->delay_usec);
- } else if(eeprom->type == e1000_eeprom_spi) {
+ } else if (eeprom->type == e1000_eeprom_spi) {
/* Toggle CS to flush commands */
eecd |= E1000_EECD_CS;
E1000_WRITE_REG(hw, EECD, eecd);
@@ -4748,7 +4765,7 @@
E1000_WRITE_REG(hw, EECD, eecd);
udelay(hw->eeprom.delay_usec);
- } else if(hw->eeprom.type == e1000_eeprom_microwire) {
+ } else if (hw->eeprom.type == e1000_eeprom_microwire) {
/* cleanup eeprom */
/* CS on Microwire is active-high */
@@ -4770,7 +4787,7 @@
}
/* Stop requesting EEPROM access */
- if(hw->mac_type > e1000_82544) {
+ if (hw->mac_type > e1000_82544) {
eecd &= ~E1000_EECD_REQ;
E1000_WRITE_REG(hw, EECD, eecd);
}
@@ -4808,12 +4825,12 @@
retry_count += 5;
e1000_standby_eeprom(hw);
- } while(retry_count < EEPROM_MAX_RETRY_SPI);
+ } while (retry_count < EEPROM_MAX_RETRY_SPI);
/* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
* only 0-5mSec on 5V devices)
*/
- if(retry_count >= EEPROM_MAX_RETRY_SPI) {
+ if (retry_count >= EEPROM_MAX_RETRY_SPI) {
DEBUGOUT("SPI EEPROM Status error\n");
return -E1000_ERR_EEPROM;
}
@@ -4844,7 +4861,7 @@
/* A check for invalid values: offset too large, too many words, and not
* enough words.
*/
- if((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
+ if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
(words == 0)) {
DEBUGOUT("\"words\" parameter out of bounds\n");
return -E1000_ERR_EEPROM;
@@ -4852,7 +4869,7 @@
/* FLASH reads without acquiring the semaphore are safe */
if (e1000_is_onboard_nvm_eeprom(hw) == TRUE &&
- hw->eeprom.use_eerd == FALSE) {
+ hw->eeprom.use_eerd == FALSE) {
switch (hw->mac_type) {
case e1000_80003es2lan:
break;
@@ -4879,7 +4896,7 @@
uint16_t word_in;
uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;
- if(e1000_spi_eeprom_ready(hw)) {
+ if (e1000_spi_eeprom_ready(hw)) {
e1000_release_eeprom(hw);
return -E1000_ERR_EEPROM;
}
@@ -4887,7 +4904,7 @@
e1000_standby_eeprom(hw);
/* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if((eeprom->address_bits == 8) && (offset >= 128))
+ if ((eeprom->address_bits == 8) && (offset >= 128))
read_opcode |= EEPROM_A8_OPCODE_SPI;
/* Send the READ command (opcode + addr) */
@@ -4903,7 +4920,7 @@
word_in = e1000_shift_in_ee_bits(hw, 16);
data[i] = (word_in >> 8) | (word_in << 8);
}
- } else if(eeprom->type == e1000_eeprom_microwire) {
+ } else if (eeprom->type == e1000_eeprom_microwire) {
for (i = 0; i < words; i++) {
/* Send the READ command (opcode + addr) */
e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE,
@@ -4948,7 +4965,7 @@
E1000_WRITE_REG(hw, EERD, eerd);
error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
- if(error) {
+ if (error) {
break;
}
data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA);
@@ -4985,7 +5002,7 @@
E1000_EEPROM_RW_REG_START;
error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
- if(error) {
+ if (error) {
break;
}
@@ -4993,7 +5010,7 @@
error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
- if(error) {
+ if (error) {
break;
}
}
@@ -5014,13 +5031,13 @@
uint32_t i, reg = 0;
int32_t done = E1000_ERR_EEPROM;
- for(i = 0; i < attempts; i++) {
- if(eerd == E1000_EEPROM_POLL_READ)
+ for (i = 0; i < attempts; i++) {
+ if (eerd == E1000_EEPROM_POLL_READ)
reg = E1000_READ_REG(hw, EERD);
else
reg = E1000_READ_REG(hw, EEWR);
- if(reg & E1000_EEPROM_RW_REG_DONE) {
+ if (reg & E1000_EEPROM_RW_REG_DONE) {
done = E1000_SUCCESS;
break;
}
@@ -5052,7 +5069,7 @@
eecd = ((eecd >> 15) & 0x03);
/* If both bits are set, device is Flash type */
- if(eecd == 0x03) {
+ if (eecd == 0x03) {
return FALSE;
}
}
@@ -5117,7 +5134,7 @@
checksum += eeprom_data;
}
- if(checksum == (uint16_t) EEPROM_SUM)
+ if (checksum == (uint16_t) EEPROM_SUM)
return E1000_SUCCESS;
else {
DEBUGOUT("EEPROM Checksum Invalid\n");
@@ -5142,15 +5159,15 @@
DEBUGFUNC("e1000_update_eeprom_checksum");
- for(i = 0; i < EEPROM_CHECKSUM_REG; i++) {
- if(e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
checksum += eeprom_data;
}
checksum = (uint16_t) EEPROM_SUM - checksum;
- if(e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
+ if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
DEBUGOUT("EEPROM Write Error\n");
return -E1000_ERR_EEPROM;
} else if (hw->eeprom.type == e1000_eeprom_flash) {
@@ -5192,14 +5209,14 @@
/* A check for invalid values: offset too large, too many words, and not
* enough words.
*/
- if((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
+ if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
(words == 0)) {
DEBUGOUT("\"words\" parameter out of bounds\n");
return -E1000_ERR_EEPROM;
}
/* 82573 writes only through eewr */
- if(eeprom->use_eewr == TRUE)
+ if (eeprom->use_eewr == TRUE)
return e1000_write_eeprom_eewr(hw, offset, words, data);
if (eeprom->type == e1000_eeprom_ich8)
@@ -5209,7 +5226,7 @@
if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
return -E1000_ERR_EEPROM;
- if(eeprom->type == e1000_eeprom_microwire) {
+ if (eeprom->type == e1000_eeprom_microwire) {
status = e1000_write_eeprom_microwire(hw, offset, words, data);
} else {
status = e1000_write_eeprom_spi(hw, offset, words, data);
@@ -5245,7 +5262,7 @@
while (widx < words) {
uint8_t write_opcode = EEPROM_WRITE_OPCODE_SPI;
- if(e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM;
+ if (e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM;
e1000_standby_eeprom(hw);
@@ -5256,7 +5273,7 @@
e1000_standby_eeprom(hw);
/* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if((eeprom->address_bits == 8) && (offset >= 128))
+ if ((eeprom->address_bits == 8) && (offset >= 128))
write_opcode |= EEPROM_A8_OPCODE_SPI;
/* Send the Write command (8-bit opcode + addr) */
@@ -5278,7 +5295,7 @@
* operation, while the smaller eeproms are capable of an 8-byte
* PAGE WRITE operation. Break the inner loop to pass new address
*/
- if((((offset + widx)*2) % eeprom->page_size) == 0) {
+ if ((((offset + widx)*2) % eeprom->page_size) == 0) {
e1000_standby_eeprom(hw);
break;
}
@@ -5344,12 +5361,12 @@
* signal that the command has been completed by raising the DO signal.
* If DO does not go high in 10 milliseconds, then error out.
*/
- for(i = 0; i < 200; i++) {
+ for (i = 0; i < 200; i++) {
eecd = E1000_READ_REG(hw, EECD);
- if(eecd & E1000_EECD_DO) break;
+ if (eecd & E1000_EECD_DO) break;
udelay(50);
}
- if(i == 200) {
+ if (i == 200) {
DEBUGOUT("EEPROM Write did not complete\n");
return -E1000_ERR_EEPROM;
}
@@ -5540,40 +5557,6 @@
}
/******************************************************************************
- * Reads the adapter's part number from the EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- * part_num - Adapter's part number
- *****************************************************************************/
-int32_t
-e1000_read_part_num(struct e1000_hw *hw,
- uint32_t *part_num)
-{
- uint16_t offset = EEPROM_PBA_BYTE_1;
- uint16_t eeprom_data;
-
- DEBUGFUNC("e1000_read_part_num");
-
- /* Get word 0 from EEPROM */
- if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- /* Save word 0 in upper half of part_num */
- *part_num = (uint32_t) (eeprom_data << 16);
-
- /* Get word 1 from EEPROM */
- if(e1000_read_eeprom(hw, ++offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- /* Save word 1 in lower half of part_num */
- *part_num |= eeprom_data;
-
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
* Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
* second function of dual function devices
*
@@ -5587,9 +5570,9 @@
DEBUGFUNC("e1000_read_mac_addr");
- for(i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+ for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
offset = i >> 1;
- if(e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -5604,12 +5587,12 @@
case e1000_82546_rev_3:
case e1000_82571:
case e1000_80003es2lan:
- if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
+ if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
hw->perm_mac_addr[5] ^= 0x01;
break;
}
- for(i = 0; i < NODE_ADDRESS_SIZE; i++)
+ for (i = 0; i < NODE_ADDRESS_SIZE; i++)
hw->mac_addr[i] = hw->perm_mac_addr[i];
return E1000_SUCCESS;
}
@@ -5648,7 +5631,7 @@
/* Zero out the other 15 receive addresses. */
DEBUGOUT("Clearing RAR[1-15]\n");
- for(i = 1; i < rar_num; i++) {
+ for (i = 1; i < rar_num; i++) {
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
E1000_WRITE_FLUSH(hw);
E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
@@ -5699,7 +5682,7 @@
if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE))
num_rar_entry -= 1;
- for(i = rar_used_count; i < num_rar_entry; i++) {
+ for (i = rar_used_count; i < num_rar_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
E1000_WRITE_FLUSH(hw);
E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
@@ -5711,13 +5694,13 @@
num_mta_entry = E1000_NUM_MTA_REGISTERS;
if (hw->mac_type == e1000_ich8lan)
num_mta_entry = E1000_NUM_MTA_REGISTERS_ICH8LAN;
- for(i = 0; i < num_mta_entry; i++) {
+ for (i = 0; i < num_mta_entry; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
E1000_WRITE_FLUSH(hw);
}
/* Add the new addresses */
- for(i = 0; i < mc_addr_count; i++) {
+ for (i = 0; i < mc_addr_count; i++) {
DEBUGOUT(" Adding the multicast addresses:\n");
DEBUGOUT7(" MC Addr #%d =%.2X %.2X %.2X %.2X %.2X %.2X\n", i,
mc_addr_list[i * (ETH_LENGTH_OF_ADDRESS + pad)],
@@ -5849,7 +5832,7 @@
* in the MTA, save off the previous entry before writing and
* restore the old value after writing.
*/
- if((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) {
+ if ((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) {
temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1));
E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta);
E1000_WRITE_FLUSH(hw);
@@ -5999,7 +5982,7 @@
DEBUGFUNC("e1000_id_led_init");
- if(hw->mac_type < e1000_82540) {
+ if (hw->mac_type < e1000_82540) {
/* Nothing to do */
return E1000_SUCCESS;
}
@@ -6009,7 +5992,7 @@
hw->ledctl_mode1 = hw->ledctl_default;
hw->ledctl_mode2 = hw->ledctl_default;
- if(e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
+ if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
DEBUGOUT("EEPROM Read Error\n");
return -E1000_ERR_EEPROM;
}
@@ -6026,7 +6009,7 @@
}
for (i = 0; i < 4; i++) {
temp = (eeprom_data >> (i << 2)) & led_mask;
- switch(temp) {
+ switch (temp) {
case ID_LED_ON1_DEF2:
case ID_LED_ON1_ON2:
case ID_LED_ON1_OFF2:
@@ -6043,7 +6026,7 @@
/* Do nothing */
break;
}
- switch(temp) {
+ switch (temp) {
case ID_LED_DEF1_ON2:
case ID_LED_ON1_ON2:
case ID_LED_OFF1_ON2:
@@ -6077,7 +6060,7 @@
DEBUGFUNC("e1000_setup_led");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
case e1000_82543:
@@ -6091,16 +6074,16 @@
/* Turn off PHY Smart Power Down (if enabled) */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
&hw->phy_spd_default);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
(uint16_t)(hw->phy_spd_default &
~IGP01E1000_GMII_SPD));
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Fall Through */
default:
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
ledctl = E1000_READ_REG(hw, LEDCTL);
/* Save current LEDCTL settings */
hw->ledctl_default = ledctl;
@@ -6111,7 +6094,7 @@
ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
E1000_LEDCTL_LED0_MODE_SHIFT);
E1000_WRITE_REG(hw, LEDCTL, ledctl);
- } else if(hw->media_type == e1000_media_type_copper)
+ } else if (hw->media_type == e1000_media_type_copper)
E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
break;
}
@@ -6119,6 +6102,7 @@
return E1000_SUCCESS;
}
+
/******************************************************************************
* Used on 82571 and later Si that has LED blink bits.
* Callers must use their own timer and should have already called
@@ -6169,7 +6153,7 @@
DEBUGFUNC("e1000_cleanup_led");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
case e1000_82543:
@@ -6183,7 +6167,7 @@
/* Turn on PHY Smart Power Down (if previously enabled) */
ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
hw->phy_spd_default);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Fall Through */
default:
@@ -6211,7 +6195,7 @@
DEBUGFUNC("e1000_led_on");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
case e1000_82543:
@@ -6220,7 +6204,7 @@
ctrl |= E1000_CTRL_SWDPIO0;
break;
case e1000_82544:
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
/* Set SW Defineable Pin 0 to turn on the LED */
ctrl |= E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
@@ -6231,7 +6215,7 @@
}
break;
default:
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
/* Clear SW Defineable Pin 0 to turn on the LED */
ctrl &= ~E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
@@ -6262,7 +6246,7 @@
DEBUGFUNC("e1000_led_off");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82542_rev2_0:
case e1000_82542_rev2_1:
case e1000_82543:
@@ -6271,7 +6255,7 @@
ctrl |= E1000_CTRL_SWDPIO0;
break;
case e1000_82544:
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
/* Clear SW Defineable Pin 0 to turn off the LED */
ctrl &= ~E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
@@ -6282,7 +6266,7 @@
}
break;
default:
- if(hw->media_type == e1000_media_type_fiber) {
+ if (hw->media_type == e1000_media_type_fiber) {
/* Set SW Defineable Pin 0 to turn off the LED */
ctrl |= E1000_CTRL_SWDPIN0;
ctrl |= E1000_CTRL_SWDPIO0;
@@ -6306,7 +6290,7 @@
*
* hw - Struct containing variables accessed by shared code
*****************************************************************************/
-static void
+void
e1000_clear_hw_cntrs(struct e1000_hw *hw)
{
volatile uint32_t temp;
@@ -6369,7 +6353,7 @@
temp = E1000_READ_REG(hw, MPTC);
temp = E1000_READ_REG(hw, BPTC);
- if(hw->mac_type < e1000_82543) return;
+ if (hw->mac_type < e1000_82543) return;
temp = E1000_READ_REG(hw, ALGNERRC);
temp = E1000_READ_REG(hw, RXERRC);
@@ -6378,13 +6362,13 @@
temp = E1000_READ_REG(hw, TSCTC);
temp = E1000_READ_REG(hw, TSCTFC);
- if(hw->mac_type <= e1000_82544) return;
+ if (hw->mac_type <= e1000_82544) return;
temp = E1000_READ_REG(hw, MGTPRC);
temp = E1000_READ_REG(hw, MGTPDC);
temp = E1000_READ_REG(hw, MGTPTC);
- if(hw->mac_type <= e1000_82547_rev_2) return;
+ if (hw->mac_type <= e1000_82547_rev_2) return;
temp = E1000_READ_REG(hw, IAC);
temp = E1000_READ_REG(hw, ICRXOC);
@@ -6415,8 +6399,8 @@
{
DEBUGFUNC("e1000_reset_adaptive");
- if(hw->adaptive_ifs) {
- if(!hw->ifs_params_forced) {
+ if (hw->adaptive_ifs) {
+ if (!hw->ifs_params_forced) {
hw->current_ifs_val = 0;
hw->ifs_min_val = IFS_MIN;
hw->ifs_max_val = IFS_MAX;
@@ -6443,12 +6427,12 @@
{
DEBUGFUNC("e1000_update_adaptive");
- if(hw->adaptive_ifs) {
- if((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
- if(hw->tx_packet_delta > MIN_NUM_XMITS) {
+ if (hw->adaptive_ifs) {
+ if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
+ if (hw->tx_packet_delta > MIN_NUM_XMITS) {
hw->in_ifs_mode = TRUE;
- if(hw->current_ifs_val < hw->ifs_max_val) {
- if(hw->current_ifs_val == 0)
+ if (hw->current_ifs_val < hw->ifs_max_val) {
+ if (hw->current_ifs_val == 0)
hw->current_ifs_val = hw->ifs_min_val;
else
hw->current_ifs_val += hw->ifs_step_size;
@@ -6456,7 +6440,7 @@
}
}
} else {
- if(hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
+ if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
hw->current_ifs_val = 0;
hw->in_ifs_mode = FALSE;
E1000_WRITE_REG(hw, AIT, 0);
@@ -6503,46 +6487,46 @@
* This could be simplified if all environments supported
* 64-bit integers.
*/
- if(carry_bit && ((stats->gorcl & 0x80000000) == 0))
+ if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
stats->gorch++;
/* Is this a broadcast or multicast? Check broadcast first,
* since the test for a multicast frame will test positive on
* a broadcast frame.
*/
- if((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff))
+ if ((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff))
/* Broadcast packet */
stats->bprc++;
- else if(*mac_addr & 0x01)
+ else if (*mac_addr & 0x01)
/* Multicast packet */
stats->mprc++;
- if(frame_len == hw->max_frame_size) {
+ if (frame_len == hw->max_frame_size) {
/* In this case, the hardware has overcounted the number of
* oversize frames.
*/
- if(stats->roc > 0)
+ if (stats->roc > 0)
stats->roc--;
}
/* Adjust the bin counters when the extra byte put the frame in the
* wrong bin. Remember that the frame_len was adjusted above.
*/
- if(frame_len == 64) {
+ if (frame_len == 64) {
stats->prc64++;
stats->prc127--;
- } else if(frame_len == 127) {
+ } else if (frame_len == 127) {
stats->prc127++;
stats->prc255--;
- } else if(frame_len == 255) {
+ } else if (frame_len == 255) {
stats->prc255++;
stats->prc511--;
- } else if(frame_len == 511) {
+ } else if (frame_len == 511) {
stats->prc511++;
stats->prc1023--;
- } else if(frame_len == 1023) {
+ } else if (frame_len == 1023) {
stats->prc1023++;
stats->prc1522--;
- } else if(frame_len == 1522) {
+ } else if (frame_len == 1522) {
stats->prc1522++;
}
}
@@ -6582,10 +6566,10 @@
hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
e1000_bus_type_pcix : e1000_bus_type_pci;
- if(hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
+ if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
e1000_bus_speed_66 : e1000_bus_speed_120;
- } else if(hw->bus_type == e1000_bus_type_pci) {
+ } else if (hw->bus_type == e1000_bus_type_pci) {
hw->bus_speed = (status & E1000_STATUS_PCI66) ?
e1000_bus_speed_66 : e1000_bus_speed_33;
} else {
@@ -6680,11 +6664,11 @@
*min_length = *max_length = 0;
/* Use old method for Phy older than IGP */
- if(hw->phy_type == e1000_phy_m88) {
+ if (hw->phy_type == e1000_phy_m88) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
M88E1000_PSSR_CABLE_LENGTH_SHIFT;
@@ -6743,7 +6727,7 @@
return -E1000_ERR_PHY;
break;
}
- } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
uint16_t cur_agc_value;
uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
@@ -6752,10 +6736,10 @@
IGP01E1000_PHY_AGC_C,
IGP01E1000_PHY_AGC_D};
/* Read the AGC registers for all channels */
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
@@ -6805,7 +6789,7 @@
if (ret_val)
return ret_val;
- /* Getting bits 15:9, which represent the combination of course and
+ /* Getting bits 15:9, which represent the combination of course and
* fine gain values. The result is a number that can be put into
* the lookup table to obtain the approximate cable length. */
cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
@@ -6870,7 +6854,7 @@
/* return the Polarity bit in the Status register. */
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
*polarity = (phy_data & M88E1000_PSSR_REV_POLARITY) >>
M88E1000_PSSR_REV_POLARITY_SHIFT;
@@ -6880,18 +6864,18 @@
/* Read the Status register to check the speed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
* find the polarity status */
- if((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
IGP01E1000_PSSR_SPEED_1000MBPS) {
/* Read the GIG initialization PCS register (0x00B4) */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Check the polarity bits */
@@ -6940,7 +6924,7 @@
hw->phy_type == e1000_phy_igp_2) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
@@ -6948,7 +6932,7 @@
(hw->phy_type == e1000_phy_gg82563)) {
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
@@ -6988,42 +6972,42 @@
DEBUGFUNC("e1000_config_dsp_after_link_change");
- if(hw->phy_type != e1000_phy_igp)
+ if (hw->phy_type != e1000_phy_igp)
return E1000_SUCCESS;
- if(link_up) {
+ if (link_up) {
ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if(ret_val) {
+ if (ret_val) {
DEBUGOUT("Error getting link speed and duplex\n");
return ret_val;
}
- if(speed == SPEED_1000) {
+ if (speed == SPEED_1000) {
ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
if (ret_val)
return ret_val;
- if((hw->dsp_config_state == e1000_dsp_config_enabled) &&
+ if ((hw->dsp_config_state == e1000_dsp_config_enabled) &&
min_length >= e1000_igp_cable_length_50) {
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i],
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i],
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
hw->dsp_config_state = e1000_dsp_config_activated;
}
- if((hw->ffe_config_state == e1000_ffe_config_enabled) &&
+ if ((hw->ffe_config_state == e1000_ffe_config_enabled) &&
(min_length < e1000_igp_cable_length_50)) {
uint16_t ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20;
@@ -7032,70 +7016,70 @@
/* clear previous idle error counts */
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
- for(i = 0; i < ffe_idle_err_timeout; i++) {
+ for (i = 0; i < ffe_idle_err_timeout; i++) {
udelay(1000);
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT);
- if(idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) {
+ if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) {
hw->ffe_config_state = e1000_ffe_config_active;
ret_val = e1000_write_phy_reg(hw,
IGP01E1000_PHY_DSP_FFE,
IGP01E1000_PHY_DSP_FFE_CM_CP);
- if(ret_val)
+ if (ret_val)
return ret_val;
break;
}
- if(idle_errs)
+ if (idle_errs)
ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100;
}
}
}
} else {
- if(hw->dsp_config_state == e1000_dsp_config_activated) {
+ if (hw->dsp_config_state == e1000_dsp_config_activated) {
/* Save off the current value of register 0x2F5B to be restored at
* the end of the routines. */
ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Disable the PHY transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_FORCE_GIGA);
- if(ret_val)
+ if (ret_val)
return ret_val;
- for(i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_RESTART_AUTONEG);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(20);
@@ -7103,40 +7087,40 @@
/* Now enable the transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->dsp_config_state = e1000_dsp_config_enabled;
}
- if(hw->ffe_config_state == e1000_ffe_config_active) {
+ if (hw->ffe_config_state == e1000_ffe_config_active) {
/* Save off the current value of register 0x2F5B to be restored at
* the end of the routines. */
ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Disable the PHY transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_FORCE_GIGA);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
IGP01E1000_PHY_DSP_FFE_DEFAULT);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, 0x0000,
IGP01E1000_IEEE_RESTART_AUTONEG);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(20);
@@ -7144,7 +7128,7 @@
/* Now enable the transmitter */
ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->ffe_config_state = e1000_ffe_config_enabled;
@@ -7169,20 +7153,20 @@
DEBUGFUNC("e1000_set_phy_mode");
- if((hw->mac_type == e1000_82545_rev_3) &&
- (hw->media_type == e1000_media_type_copper)) {
+ if ((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data);
- if(ret_val) {
+ if (ret_val) {
return ret_val;
}
- if((eeprom_data != EEPROM_RESERVED_WORD) &&
- (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ if ((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104);
- if(ret_val)
+ if (ret_val)
return ret_val;
hw->phy_reset_disable = FALSE;
@@ -7233,16 +7217,16 @@
phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
} else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
- if(!active) {
- if(hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547_rev_2) {
+ if (!active) {
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else {
if (hw->mac_type == e1000_ich8lan) {
@@ -7264,13 +7248,13 @@
if (hw->smart_speed == e1000_smart_speed_on) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else if (hw->smart_speed == e1000_smart_speed_off) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
@@ -7281,19 +7265,19 @@
phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
- } else if((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
+ } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) ||
+ (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
+ (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
- if(hw->mac_type == e1000_82541_rev_2 ||
+ if (hw->mac_type == e1000_82541_rev_2 ||
hw->mac_type == e1000_82547_rev_2) {
phy_data |= IGP01E1000_GMII_FLEX_SPD;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else {
if (hw->mac_type == e1000_ich8lan) {
@@ -7310,12 +7294,12 @@
/* When LPLU is enabled we should disable SmartSpeed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -7345,14 +7329,14 @@
uint16_t phy_data;
DEBUGFUNC("e1000_set_d0_lplu_state");
- if(hw->mac_type <= e1000_82547_rev_2)
+ if (hw->mac_type <= e1000_82547_rev_2)
return E1000_SUCCESS;
if (hw->mac_type == e1000_ich8lan) {
phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
} else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -7374,13 +7358,13 @@
if (hw->smart_speed == e1000_smart_speed_on) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
&phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
} else if (hw->smart_speed == e1000_smart_speed_off) {
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
@@ -7391,7 +7375,7 @@
phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -7410,12 +7394,12 @@
/* When LPLU is enabled we should disable SmartSpeed */
ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
}
@@ -7436,7 +7420,7 @@
DEBUGFUNC("e1000_set_vco_speed");
- switch(hw->mac_type) {
+ switch (hw->mac_type) {
case e1000_82545_rev_3:
case e1000_82546_rev_3:
break;
@@ -7447,39 +7431,39 @@
/* Set PHY register 30, page 5, bit 8 to 0 */
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* Set PHY register 30, page 4, bit 11 to 1 */
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
phy_data |= M88E1000_PHY_VCO_REG_BIT11;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
- if(ret_val)
+ if (ret_val)
return ret_val;
return E1000_SUCCESS;
@@ -7558,7 +7542,7 @@
{
uint8_t *tmp;
uint8_t *bufptr = buffer;
- uint32_t data;
+ uint32_t data = 0;
uint16_t remaining, i, j, prev_bytes;
/* sum = only sum of the data and it is not checksum */
@@ -7638,7 +7622,7 @@
buffer = (uint8_t *) hdr;
i = length;
- while(i--)
+ while (i--)
sum += buffer[i];
hdr->checksum = 0 - sum;
@@ -7661,8 +7645,7 @@
* returns - E1000_SUCCESS for success.
****************************************************************************/
static int32_t
-e1000_mng_write_commit(
- struct e1000_hw * hw)
+e1000_mng_write_commit(struct e1000_hw * hw)
{
uint32_t hicr;
@@ -7834,31 +7817,31 @@
/* Disable the transmitter on the PHY */
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* This loop will early-out if the NO link condition has been met. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
/* Read the MII Status Register and wait for Link Status bit
* to be clear.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break;
+ if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break;
msec_delay_irq(100);
}
@@ -7868,40 +7851,40 @@
/* Now we will re-enable th transmitter on the PHY */
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(50);
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(50);
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
- if(ret_val)
+ if (ret_val)
return ret_val;
msec_delay_irq(50);
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
- if(ret_val)
+ if (ret_val)
return ret_val;
/* This loop will early-out if the link condition has been met. */
- for(i = PHY_FORCE_TIME; i > 0; i--) {
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
/* Read the MII Status Register and wait for Link Status bit
* to be set.
*/
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if(ret_val)
+ if (ret_val)
return ret_val;
- if(mii_status_reg & MII_SR_LINK_STATUS) break;
+ if (mii_status_reg & MII_SR_LINK_STATUS) break;
msec_delay_irq(100);
}
return E1000_SUCCESS;
@@ -7980,15 +7963,15 @@
e1000_set_pci_express_master_disable(hw);
- while(timeout) {
- if(!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
+ while (timeout) {
+ if (!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
break;
else
udelay(100);
timeout--;
}
- if(!timeout) {
+ if (!timeout) {
DEBUGOUT("Master requests are pending.\n");
return -E1000_ERR_MASTER_REQUESTS_PENDING;
}
@@ -8029,7 +8012,7 @@
timeout--;
}
- if(!timeout) {
+ if (!timeout) {
DEBUGOUT("Auto read by HW from EEPROM has not completed.\n");
return -E1000_ERR_RESET;
}
@@ -8110,7 +8093,7 @@
DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
- if(!hw->eeprom_semaphore_present)
+ if (!hw->eeprom_semaphore_present)
return E1000_SUCCESS;
if (hw->mac_type == e1000_80003es2lan) {
@@ -8121,20 +8104,20 @@
/* Get the FW semaphore. */
timeout = hw->eeprom.word_size + 1;
- while(timeout) {
+ while (timeout) {
swsm = E1000_READ_REG(hw, SWSM);
swsm |= E1000_SWSM_SWESMBI;
E1000_WRITE_REG(hw, SWSM, swsm);
/* if we managed to set the bit we got the semaphore. */
swsm = E1000_READ_REG(hw, SWSM);
- if(swsm & E1000_SWSM_SWESMBI)
+ if (swsm & E1000_SWSM_SWESMBI)
break;
udelay(50);
timeout--;
}
- if(!timeout) {
+ if (!timeout) {
/* Release semaphores */
e1000_put_hw_eeprom_semaphore(hw);
DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
@@ -8159,7 +8142,7 @@
DEBUGFUNC("e1000_put_hw_eeprom_semaphore");
- if(!hw->eeprom_semaphore_present)
+ if (!hw->eeprom_semaphore_present)
return;
swsm = E1000_READ_REG(hw, SWSM);
@@ -8192,16 +8175,16 @@
if (hw->mac_type != e1000_80003es2lan)
return E1000_SUCCESS;
- while(timeout) {
+ while (timeout) {
swsm = E1000_READ_REG(hw, SWSM);
/* If SMBI bit cleared, it is now set and we hold the semaphore */
- if(!(swsm & E1000_SWSM_SMBI))
+ if (!(swsm & E1000_SWSM_SMBI))
break;
msec_delay_irq(1);
timeout--;
}
- if(!timeout) {
+ if (!timeout) {
DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
return -E1000_ERR_RESET;
}
@@ -8277,7 +8260,7 @@
case e1000_82573:
case e1000_80003es2lan:
fwsm = E1000_READ_REG(hw, FWSM);
- if((fwsm & E1000_FWSM_MODE_MASK) != 0)
+ if ((fwsm & E1000_FWSM_MODE_MASK) != 0)
return TRUE;
break;
case e1000_ich8lan:
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index 375b955..a170e96 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -336,9 +336,9 @@
#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
-#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
-#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
-#define E1000_MNG_IAMT_MODE 0x3
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
+#define E1000_MNG_IAMT_MODE 0x3
#define E1000_MNG_ICH_IAMT_MODE 0x2
#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
@@ -385,7 +385,7 @@
#endif
int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer,
- uint16_t length);
+ uint16_t length);
boolean_t e1000_check_mng_mode(struct e1000_hw *hw);
boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
@@ -470,6 +470,7 @@
#define E1000_DEV_ID_82571EB_COPPER 0x105E
#define E1000_DEV_ID_82571EB_FIBER 0x105F
#define E1000_DEV_ID_82571EB_SERDES 0x1060
+#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
#define E1000_DEV_ID_82572EI_COPPER 0x107D
#define E1000_DEV_ID_82572EI_FIBER 0x107E
#define E1000_DEV_ID_82572EI_SERDES 0x107F
@@ -523,7 +524,7 @@
/* 802.1q VLAN Packet Sizes */
-#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
+#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
/* Ethertype field values */
#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
@@ -697,6 +698,7 @@
E1000_RXDEXT_STATERR_CXE | \
E1000_RXDEXT_STATERR_RXE)
+
/* Transmit Descriptor */
struct e1000_tx_desc {
uint64_t buffer_addr; /* Address of the descriptor's data buffer */
@@ -2086,7 +2088,7 @@
#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
* filtering */
#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
-#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
@@ -2172,7 +2174,7 @@
#define E1000_MDALIGN 4096
-/* PCI-Ex registers */
+/* PCI-Ex registers*/
/* PCI-Ex Control Register */
#define E1000_GCR_RXD_NO_SNOOP 0x00000001
@@ -2224,7 +2226,7 @@
#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erast/write disable */
/* EEPROM Commands - SPI */
-#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
@@ -3082,10 +3084,10 @@
/* DSP Distance Register (Page 5, Register 26) */
#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M;
- 1 = 50-80M;
- 2 = 80-110M;
- 3 = 110-140M;
- 4 = >140M */
+ 1 = 50-80M;
+ 2 = 80-110M;
+ 3 = 110-140M;
+ 4 = >140M */
/* Kumeran Mode Control Register (Page 193, Register 16) */
#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index 726f43d..1d7c999 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -36,7 +36,7 @@
#else
#define DRIVERNAPI "-NAPI"
#endif
-#define DRV_VERSION "7.1.9-k4"DRIVERNAPI
+#define DRV_VERSION "7.2.7-k2"DRIVERNAPI
char e1000_driver_version[] = DRV_VERSION;
static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
@@ -48,7 +48,6 @@
* {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
*/
static struct pci_device_id e1000_pci_tbl[] = {
- INTEL_E1000_ETHERNET_DEVICE(0x1000),
INTEL_E1000_ETHERNET_DEVICE(0x1001),
INTEL_E1000_ETHERNET_DEVICE(0x1004),
INTEL_E1000_ETHERNET_DEVICE(0x1008),
@@ -99,6 +98,7 @@
INTEL_E1000_ETHERNET_DEVICE(0x1098),
INTEL_E1000_ETHERNET_DEVICE(0x1099),
INTEL_E1000_ETHERNET_DEVICE(0x109A),
+ INTEL_E1000_ETHERNET_DEVICE(0x10A4),
INTEL_E1000_ETHERNET_DEVICE(0x10B5),
INTEL_E1000_ETHERNET_DEVICE(0x10B9),
INTEL_E1000_ETHERNET_DEVICE(0x10BA),
@@ -245,7 +245,7 @@
printk(KERN_INFO "%s\n", e1000_copyright);
- ret = pci_module_init(&e1000_driver);
+ ret = pci_register_driver(&e1000_driver);
return ret;
}
@@ -485,7 +485,7 @@
*
**/
-static void e1000_power_up_phy(struct e1000_adapter *adapter)
+void e1000_power_up_phy(struct e1000_adapter *adapter)
{
uint16_t mii_reg = 0;
@@ -682,9 +682,9 @@
unsigned long flash_start, flash_len;
static int cards_found = 0;
- static int e1000_ksp3_port_a = 0; /* global ksp3 port a indication */
+ static int global_quad_port_a = 0; /* global ksp3 port a indication */
int i, err, pci_using_dac;
- uint16_t eeprom_data;
+ uint16_t eeprom_data = 0;
uint16_t eeprom_apme_mask = E1000_EEPROM_APME;
if ((err = pci_enable_device(pdev)))
return err;
@@ -696,21 +696,20 @@
if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) &&
(err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK))) {
E1000_ERR("No usable DMA configuration, aborting\n");
- return err;
+ goto err_dma;
}
pci_using_dac = 0;
}
if ((err = pci_request_regions(pdev, e1000_driver_name)))
- return err;
+ goto err_pci_reg;
pci_set_master(pdev);
+ err = -ENOMEM;
netdev = alloc_etherdev(sizeof(struct e1000_adapter));
- if (!netdev) {
- err = -ENOMEM;
+ if (!netdev)
goto err_alloc_etherdev;
- }
SET_MODULE_OWNER(netdev);
SET_NETDEV_DEV(netdev, &pdev->dev);
@@ -725,11 +724,10 @@
mmio_start = pci_resource_start(pdev, BAR_0);
mmio_len = pci_resource_len(pdev, BAR_0);
+ err = -EIO;
adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
- if (!adapter->hw.hw_addr) {
- err = -EIO;
+ if (!adapter->hw.hw_addr)
goto err_ioremap;
- }
for (i = BAR_1; i <= BAR_5; i++) {
if (pci_resource_len(pdev, i) == 0)
@@ -774,6 +772,7 @@
if ((err = e1000_sw_init(adapter)))
goto err_sw_init;
+ err = -EIO;
/* Flash BAR mapping must happen after e1000_sw_init
* because it depends on mac_type */
if ((adapter->hw.mac_type == e1000_ich8lan) &&
@@ -781,24 +780,13 @@
flash_start = pci_resource_start(pdev, 1);
flash_len = pci_resource_len(pdev, 1);
adapter->hw.flash_address = ioremap(flash_start, flash_len);
- if (!adapter->hw.flash_address) {
- err = -EIO;
+ if (!adapter->hw.flash_address)
goto err_flashmap;
- }
}
- if ((err = e1000_check_phy_reset_block(&adapter->hw)))
+ if (e1000_check_phy_reset_block(&adapter->hw))
DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
- /* if ksp3, indicate if it's port a being setup */
- if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
- e1000_ksp3_port_a == 0)
- adapter->ksp3_port_a = 1;
- e1000_ksp3_port_a++;
- /* Reset for multiple KP3 adapters */
- if (e1000_ksp3_port_a == 4)
- e1000_ksp3_port_a = 0;
-
if (adapter->hw.mac_type >= e1000_82543) {
netdev->features = NETIF_F_SG |
NETIF_F_HW_CSUM |
@@ -830,7 +818,7 @@
if (e1000_init_eeprom_params(&adapter->hw)) {
E1000_ERR("EEPROM initialization failed\n");
- return -EIO;
+ goto err_eeprom;
}
/* before reading the EEPROM, reset the controller to
@@ -842,7 +830,6 @@
if (e1000_validate_eeprom_checksum(&adapter->hw) < 0) {
DPRINTK(PROBE, ERR, "The EEPROM Checksum Is Not Valid\n");
- err = -EIO;
goto err_eeprom;
}
@@ -855,12 +842,9 @@
if (!is_valid_ether_addr(netdev->perm_addr)) {
DPRINTK(PROBE, ERR, "Invalid MAC Address\n");
- err = -EIO;
goto err_eeprom;
}
- e1000_read_part_num(&adapter->hw, &(adapter->part_num));
-
e1000_get_bus_info(&adapter->hw);
init_timer(&adapter->tx_fifo_stall_timer);
@@ -921,7 +905,38 @@
break;
}
if (eeprom_data & eeprom_apme_mask)
- adapter->wol |= E1000_WUFC_MAG;
+ adapter->eeprom_wol |= E1000_WUFC_MAG;
+
+ /* now that we have the eeprom settings, apply the special cases
+ * where the eeprom may be wrong or the board simply won't support
+ * wake on lan on a particular port */
+ switch (pdev->device) {
+ case E1000_DEV_ID_82546GB_PCIE:
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546EB_FIBER:
+ case E1000_DEV_ID_82546GB_FIBER:
+ case E1000_DEV_ID_82571EB_FIBER:
+ /* Wake events only supported on port A for dual fiber
+ * regardless of eeprom setting */
+ if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1)
+ adapter->eeprom_wol = 0;
+ break;
+ case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
+ case E1000_DEV_ID_82571EB_QUAD_COPPER:
+ /* if quad port adapter, disable WoL on all but port A */
+ if (global_quad_port_a != 0)
+ adapter->eeprom_wol = 0;
+ else
+ adapter->quad_port_a = 1;
+ /* Reset for multiple quad port adapters */
+ if (++global_quad_port_a == 4)
+ global_quad_port_a = 0;
+ break;
+ }
+
+ /* initialize the wol settings based on the eeprom settings */
+ adapter->wol = adapter->eeprom_wol;
/* print bus type/speed/width info */
{
@@ -964,16 +979,33 @@
return 0;
err_register:
+ e1000_release_hw_control(adapter);
+err_eeprom:
+ if (!e1000_check_phy_reset_block(&adapter->hw))
+ e1000_phy_hw_reset(&adapter->hw);
+
if (adapter->hw.flash_address)
iounmap(adapter->hw.flash_address);
err_flashmap:
+#ifdef CONFIG_E1000_NAPI
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ dev_put(&adapter->polling_netdev[i]);
+#endif
+
+ kfree(adapter->tx_ring);
+ kfree(adapter->rx_ring);
+#ifdef CONFIG_E1000_NAPI
+ kfree(adapter->polling_netdev);
+#endif
err_sw_init:
-err_eeprom:
iounmap(adapter->hw.hw_addr);
err_ioremap:
free_netdev(netdev);
err_alloc_etherdev:
pci_release_regions(pdev);
+err_pci_reg:
+err_dma:
+ pci_disable_device(pdev);
return err;
}
@@ -1208,7 +1240,7 @@
err = e1000_request_irq(adapter);
if (err)
- goto err_up;
+ goto err_req_irq;
e1000_power_up_phy(adapter);
@@ -1229,6 +1261,9 @@
return E1000_SUCCESS;
err_up:
+ e1000_power_down_phy(adapter);
+ e1000_free_irq(adapter);
+err_req_irq:
e1000_free_all_rx_resources(adapter);
err_setup_rx:
e1000_free_all_tx_resources(adapter);
@@ -1381,10 +1416,6 @@
* (Descriptors) for all queues
* @adapter: board private structure
*
- * If this function returns with an error, then it's possible one or
- * more of the rings is populated (while the rest are not). It is the
- * callers duty to clean those orphaned rings.
- *
* Return 0 on success, negative on failure
**/
@@ -1398,6 +1429,9 @@
if (err) {
DPRINTK(PROBE, ERR,
"Allocation for Tx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_tx_resources(adapter,
+ &adapter->tx_ring[i]);
break;
}
}
@@ -1499,8 +1533,6 @@
} else if (hw->mac_type == e1000_80003es2lan) {
tarc = E1000_READ_REG(hw, TARC0);
tarc |= 1;
- if (hw->media_type == e1000_media_type_internal_serdes)
- tarc |= (1 << 20);
E1000_WRITE_REG(hw, TARC0, tarc);
tarc = E1000_READ_REG(hw, TARC1);
tarc |= 1;
@@ -1639,10 +1671,6 @@
* (Descriptors) for all queues
* @adapter: board private structure
*
- * If this function returns with an error, then it's possible one or
- * more of the rings is populated (while the rest are not). It is the
- * callers duty to clean those orphaned rings.
- *
* Return 0 on success, negative on failure
**/
@@ -1656,6 +1684,9 @@
if (err) {
DPRINTK(PROBE, ERR,
"Allocation for Rx Queue %u failed\n", i);
+ for (i-- ; i >= 0; i--)
+ e1000_free_rx_resources(adapter,
+ &adapter->rx_ring[i]);
break;
}
}
@@ -2442,10 +2473,9 @@
* disable receives in the ISR and
* reset device here in the watchdog
*/
- if (adapter->hw.mac_type == e1000_80003es2lan) {
+ if (adapter->hw.mac_type == e1000_80003es2lan)
/* reset device */
schedule_work(&adapter->reset_task);
- }
}
e1000_smartspeed(adapter);
@@ -2545,7 +2575,7 @@
cmd_length = E1000_TXD_CMD_IP;
ipcse = skb->h.raw - skb->data - 1;
#ifdef NETIF_F_TSO_IPV6
- } else if (skb->protocol == ntohs(ETH_P_IPV6)) {
+ } else if (skb->protocol == htons(ETH_P_IPV6)) {
skb->nh.ipv6h->payload_len = 0;
skb->h.th->check =
~csum_ipv6_magic(&skb->nh.ipv6h->saddr,
@@ -3680,7 +3710,7 @@
E1000_DBG("%s: Receive packet consumed multiple"
" buffers\n", netdev->name);
/* recycle */
- buffer_info-> skb = skb;
+ buffer_info->skb = skb;
goto next_desc;
}
@@ -3711,7 +3741,6 @@
netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
if (new_skb) {
skb_reserve(new_skb, NET_IP_ALIGN);
- new_skb->dev = netdev;
memcpy(new_skb->data - NET_IP_ALIGN,
skb->data - NET_IP_ALIGN,
length + NET_IP_ALIGN);
@@ -3978,13 +4007,13 @@
buffer_info = &rx_ring->buffer_info[i];
while (cleaned_count--) {
- if (!(skb = buffer_info->skb))
- skb = netdev_alloc_skb(netdev, bufsz);
- else {
+ skb = buffer_info->skb;
+ if (skb) {
skb_trim(skb, 0);
goto map_skb;
}
+ skb = netdev_alloc_skb(netdev, bufsz);
if (unlikely(!skb)) {
/* Better luck next round */
adapter->alloc_rx_buff_failed++;
@@ -4009,10 +4038,10 @@
dev_kfree_skb(skb);
dev_kfree_skb(oldskb);
break; /* while !buffer_info->skb */
- } else {
- /* Use new allocation */
- dev_kfree_skb(oldskb);
}
+
+ /* Use new allocation */
+ dev_kfree_skb(oldskb);
}
/* Make buffer alignment 2 beyond a 16 byte boundary
* this will result in a 16 byte aligned IP header after
@@ -4020,8 +4049,6 @@
*/
skb_reserve(skb, NET_IP_ALIGN);
- skb->dev = netdev;
-
buffer_info->skb = skb;
buffer_info->length = adapter->rx_buffer_len;
map_skb:
@@ -4135,8 +4162,6 @@
*/
skb_reserve(skb, NET_IP_ALIGN);
- skb->dev = netdev;
-
buffer_info->skb = skb;
buffer_info->length = adapter->rx_ps_bsize0;
buffer_info->dma = pci_map_single(pdev, skb->data,
@@ -4628,7 +4653,7 @@
e1000_set_multi(netdev);
/* turn on all-multi mode if wake on multicast is enabled */
- if (adapter->wol & E1000_WUFC_MC) {
+ if (wufc & E1000_WUFC_MC) {
rctl = E1000_READ_REG(&adapter->hw, RCTL);
rctl |= E1000_RCTL_MPE;
E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
@@ -4700,11 +4725,14 @@
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
- uint32_t manc, ret_val;
+ uint32_t manc, err;
pci_set_power_state(pdev, PCI_D0);
e1000_pci_restore_state(adapter);
- ret_val = pci_enable_device(pdev);
+ if ((err = pci_enable_device(pdev))) {
+ printk(KERN_ERR "e1000: Cannot enable PCI device from suspend\n");
+ return err;
+ }
pci_set_master(pdev);
pci_enable_wake(pdev, PCI_D3hot, 0);
diff --git a/drivers/net/e1000/e1000_param.c b/drivers/net/e1000/e1000_param.c
index 0ef4131..2128427 100644
--- a/drivers/net/e1000/e1000_param.c
+++ b/drivers/net/e1000/e1000_param.c
@@ -324,7 +324,6 @@
DPRINTK(PROBE, NOTICE,
"Warning: no configuration for board #%i\n", bd);
DPRINTK(PROBE, NOTICE, "Using defaults for all values\n");
- bd = E1000_MAX_NIC;
}
{ /* Transmit Descriptor Count */
@@ -342,9 +341,14 @@
opt.arg.r.max = mac_type < e1000_82544 ?
E1000_MAX_TXD : E1000_MAX_82544_TXD;
- tx_ring->count = TxDescriptors[bd];
- e1000_validate_option(&tx_ring->count, &opt, adapter);
- E1000_ROUNDUP(tx_ring->count, REQ_TX_DESCRIPTOR_MULTIPLE);
+ if (num_TxDescriptors > bd) {
+ tx_ring->count = TxDescriptors[bd];
+ e1000_validate_option(&tx_ring->count, &opt, adapter);
+ E1000_ROUNDUP(tx_ring->count,
+ REQ_TX_DESCRIPTOR_MULTIPLE);
+ } else {
+ tx_ring->count = opt.def;
+ }
for (i = 0; i < adapter->num_tx_queues; i++)
tx_ring[i].count = tx_ring->count;
}
@@ -363,9 +367,14 @@
opt.arg.r.max = mac_type < e1000_82544 ? E1000_MAX_RXD :
E1000_MAX_82544_RXD;
- rx_ring->count = RxDescriptors[bd];
- e1000_validate_option(&rx_ring->count, &opt, adapter);
- E1000_ROUNDUP(rx_ring->count, REQ_RX_DESCRIPTOR_MULTIPLE);
+ if (num_RxDescriptors > bd) {
+ rx_ring->count = RxDescriptors[bd];
+ e1000_validate_option(&rx_ring->count, &opt, adapter);
+ E1000_ROUNDUP(rx_ring->count,
+ REQ_RX_DESCRIPTOR_MULTIPLE);
+ } else {
+ rx_ring->count = opt.def;
+ }
for (i = 0; i < adapter->num_rx_queues; i++)
rx_ring[i].count = rx_ring->count;
}
@@ -377,9 +386,13 @@
.def = OPTION_ENABLED
};
- int rx_csum = XsumRX[bd];
- e1000_validate_option(&rx_csum, &opt, adapter);
- adapter->rx_csum = rx_csum;
+ if (num_XsumRX > bd) {
+ int rx_csum = XsumRX[bd];
+ e1000_validate_option(&rx_csum, &opt, adapter);
+ adapter->rx_csum = rx_csum;
+ } else {
+ adapter->rx_csum = opt.def;
+ }
}
{ /* Flow Control */
@@ -399,9 +412,13 @@
.p = fc_list }}
};
- int fc = FlowControl[bd];
- e1000_validate_option(&fc, &opt, adapter);
- adapter->hw.fc = adapter->hw.original_fc = fc;
+ if (num_FlowControl > bd) {
+ int fc = FlowControl[bd];
+ e1000_validate_option(&fc, &opt, adapter);
+ adapter->hw.fc = adapter->hw.original_fc = fc;
+ } else {
+ adapter->hw.fc = adapter->hw.original_fc = opt.def;
+ }
}
{ /* Transmit Interrupt Delay */
struct e1000_option opt = {
@@ -413,8 +430,13 @@
.max = MAX_TXDELAY }}
};
- adapter->tx_int_delay = TxIntDelay[bd];
- e1000_validate_option(&adapter->tx_int_delay, &opt, adapter);
+ if (num_TxIntDelay > bd) {
+ adapter->tx_int_delay = TxIntDelay[bd];
+ e1000_validate_option(&adapter->tx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_int_delay = opt.def;
+ }
}
{ /* Transmit Absolute Interrupt Delay */
struct e1000_option opt = {
@@ -426,9 +448,13 @@
.max = MAX_TXABSDELAY }}
};
- adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
- e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
- adapter);
+ if (num_TxAbsIntDelay > bd) {
+ adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->tx_abs_int_delay = opt.def;
+ }
}
{ /* Receive Interrupt Delay */
struct e1000_option opt = {
@@ -440,8 +466,13 @@
.max = MAX_RXDELAY }}
};
- adapter->rx_int_delay = RxIntDelay[bd];
- e1000_validate_option(&adapter->rx_int_delay, &opt, adapter);
+ if (num_RxIntDelay > bd) {
+ adapter->rx_int_delay = RxIntDelay[bd];
+ e1000_validate_option(&adapter->rx_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_int_delay = opt.def;
+ }
}
{ /* Receive Absolute Interrupt Delay */
struct e1000_option opt = {
@@ -453,9 +484,13 @@
.max = MAX_RXABSDELAY }}
};
- adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
- e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
- adapter);
+ if (num_RxAbsIntDelay > bd) {
+ adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
+ e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
+ adapter);
+ } else {
+ adapter->rx_abs_int_delay = opt.def;
+ }
}
{ /* Interrupt Throttling Rate */
struct e1000_option opt = {
@@ -467,18 +502,24 @@
.max = MAX_ITR }}
};
- adapter->itr = InterruptThrottleRate[bd];
- switch (adapter->itr) {
- case 0:
- DPRINTK(PROBE, INFO, "%s turned off\n", opt.name);
- break;
- case 1:
- DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
- opt.name);
- break;
- default:
- e1000_validate_option(&adapter->itr, &opt, adapter);
- break;
+ if (num_InterruptThrottleRate > bd) {
+ adapter->itr = InterruptThrottleRate[bd];
+ switch (adapter->itr) {
+ case 0:
+ DPRINTK(PROBE, INFO, "%s turned off\n",
+ opt.name);
+ break;
+ case 1:
+ DPRINTK(PROBE, INFO, "%s set to dynamic mode\n",
+ opt.name);
+ break;
+ default:
+ e1000_validate_option(&adapter->itr, &opt,
+ adapter);
+ break;
+ }
+ } else {
+ adapter->itr = opt.def;
}
}
{ /* Smart Power Down */
@@ -489,9 +530,13 @@
.def = OPTION_DISABLED
};
- int spd = SmartPowerDownEnable[bd];
- e1000_validate_option(&spd, &opt, adapter);
- adapter->smart_power_down = spd;
+ if (num_SmartPowerDownEnable > bd) {
+ int spd = SmartPowerDownEnable[bd];
+ e1000_validate_option(&spd, &opt, adapter);
+ adapter->smart_power_down = spd;
+ } else {
+ adapter->smart_power_down = opt.def;
+ }
}
{ /* Kumeran Lock Loss Workaround */
struct e1000_option opt = {
@@ -501,9 +546,13 @@
.def = OPTION_ENABLED
};
+ if (num_KumeranLockLoss > bd) {
int kmrn_lock_loss = KumeranLockLoss[bd];
e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss;
+ } else {
+ adapter->hw.kmrn_lock_loss_workaround_disabled = !opt.def;
+ }
}
switch (adapter->hw.media_type) {
@@ -530,18 +579,17 @@
e1000_check_fiber_options(struct e1000_adapter *adapter)
{
int bd = adapter->bd_number;
- bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
- if ((Speed[bd] != OPTION_UNSET)) {
+ if (num_Speed > bd) {
DPRINTK(PROBE, INFO, "Speed not valid for fiber adapters, "
"parameter ignored\n");
}
- if ((Duplex[bd] != OPTION_UNSET)) {
+ if (num_Duplex > bd) {
DPRINTK(PROBE, INFO, "Duplex not valid for fiber adapters, "
"parameter ignored\n");
}
- if ((AutoNeg[bd] != OPTION_UNSET) && (AutoNeg[bd] != 0x20)) {
+ if ((num_AutoNeg > bd) && (AutoNeg[bd] != 0x20)) {
DPRINTK(PROBE, INFO, "AutoNeg other than 1000/Full is "
"not valid for fiber adapters, "
"parameter ignored\n");
@@ -560,7 +608,6 @@
{
int speed, dplx, an;
int bd = adapter->bd_number;
- bd = bd > E1000_MAX_NIC ? E1000_MAX_NIC : bd;
{ /* Speed */
struct e1000_opt_list speed_list[] = {{ 0, "" },
@@ -577,8 +624,12 @@
.p = speed_list }}
};
- speed = Speed[bd];
- e1000_validate_option(&speed, &opt, adapter);
+ if (num_Speed > bd) {
+ speed = Speed[bd];
+ e1000_validate_option(&speed, &opt, adapter);
+ } else {
+ speed = opt.def;
+ }
}
{ /* Duplex */
struct e1000_opt_list dplx_list[] = {{ 0, "" },
@@ -600,11 +651,15 @@
"Speed/Duplex/AutoNeg parameter ignored.\n");
return;
}
- dplx = Duplex[bd];
- e1000_validate_option(&dplx, &opt, adapter);
+ if (num_Duplex > bd) {
+ dplx = Duplex[bd];
+ e1000_validate_option(&dplx, &opt, adapter);
+ } else {
+ dplx = opt.def;
+ }
}
- if (AutoNeg[bd] != OPTION_UNSET && (speed != 0 || dplx != 0)) {
+ if ((num_AutoNeg > bd) && (speed != 0 || dplx != 0)) {
DPRINTK(PROBE, INFO,
"AutoNeg specified along with Speed or Duplex, "
"parameter ignored\n");
@@ -653,15 +708,19 @@
.p = an_list }}
};
- an = AutoNeg[bd];
- e1000_validate_option(&an, &opt, adapter);
+ if (num_AutoNeg > bd) {
+ an = AutoNeg[bd];
+ e1000_validate_option(&an, &opt, adapter);
+ } else {
+ an = opt.def;
+ }
adapter->hw.autoneg_advertised = an;
}
switch (speed + dplx) {
case 0:
adapter->hw.autoneg = adapter->fc_autoneg = 1;
- if (Speed[bd] != OPTION_UNSET || Duplex[bd] != OPTION_UNSET)
+ if ((num_Speed > bd) && (speed != 0 || dplx != 0))
DPRINTK(PROBE, INFO,
"Speed and duplex autonegotiation enabled\n");
break;
diff --git a/drivers/net/eepro100.c b/drivers/net/eepro100.c
index e445988..a3d515d 100644
--- a/drivers/net/eepro100.c
+++ b/drivers/net/eepro100.c
@@ -2385,7 +2385,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init(&eepro100_driver);
+ return pci_register_driver(&eepro100_driver);
}
static void __exit eepro100_cleanup_module(void)
diff --git a/drivers/net/epic100.c b/drivers/net/epic100.c
index a67650cc..25c4619 100644
--- a/drivers/net/epic100.c
+++ b/drivers/net/epic100.c
@@ -1604,7 +1604,7 @@
version, version2, version3);
#endif
- return pci_module_init (&epic_driver);
+ return pci_register_driver(&epic_driver);
}
diff --git a/drivers/net/fealnx.c b/drivers/net/fealnx.c
index 567e274..a2121fa 100644
--- a/drivers/net/fealnx.c
+++ b/drivers/net/fealnx.c
@@ -1984,7 +1984,7 @@
printk(version);
#endif
- return pci_module_init(&fealnx_driver);
+ return pci_register_driver(&fealnx_driver);
}
static void __exit fealnx_exit(void)
diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c
index 11b8f1b..8c8f7cf 100644
--- a/drivers/net/forcedeth.c
+++ b/drivers/net/forcedeth.c
@@ -109,6 +109,7 @@
* 0.54: 21 Mar 2006: Fix spin locks for multi irqs and cleanup.
* 0.55: 22 Mar 2006: Add flow control (pause frame).
* 0.56: 22 Mar 2006: Additional ethtool config and moduleparam support.
+ * 0.57: 14 May 2006: Mac address set in probe/remove and order corrections.
*
* Known bugs:
* We suspect that on some hardware no TX done interrupts are generated.
@@ -120,7 +121,12 @@
* DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few
* superfluous timer interrupts from the nic.
*/
-#define FORCEDETH_VERSION "0.56"
+#ifdef CONFIG_FORCEDETH_NAPI
+#define DRIVERNAPI "-NAPI"
+#else
+#define DRIVERNAPI
+#endif
+#define FORCEDETH_VERSION "0.57"
#define DRV_NAME "forcedeth"
#include <linux/module.h>
@@ -262,7 +268,8 @@
NvRegRingSizes = 0x108,
#define NVREG_RINGSZ_TXSHIFT 0
#define NVREG_RINGSZ_RXSHIFT 16
- NvRegUnknownTransmitterReg = 0x10c,
+ NvRegTransmitPoll = 0x10c,
+#define NVREG_TRANSMITPOLL_MAC_ADDR_REV 0x00008000
NvRegLinkSpeed = 0x110,
#define NVREG_LINKSPEED_FORCE 0x10000
#define NVREG_LINKSPEED_10 1000
@@ -381,21 +388,21 @@
/* Big endian: should work, but is untested */
struct ring_desc {
- u32 PacketBuffer;
- u32 FlagLen;
+ __le32 buf;
+ __le32 flaglen;
};
struct ring_desc_ex {
- u32 PacketBufferHigh;
- u32 PacketBufferLow;
- u32 TxVlan;
- u32 FlagLen;
+ __le32 bufhigh;
+ __le32 buflow;
+ __le32 txvlan;
+ __le32 flaglen;
};
-typedef union _ring_type {
+union ring_type {
struct ring_desc* orig;
struct ring_desc_ex* ex;
-} ring_type;
+};
#define FLAG_MASK_V1 0xffff0000
#define FLAG_MASK_V2 0xffffc000
@@ -653,8 +660,8 @@
};
struct register_test {
- u32 reg;
- u32 mask;
+ __le32 reg;
+ __le32 mask;
};
static const struct register_test nv_registers_test[] = {
@@ -713,7 +720,7 @@
/* rx specific fields.
* Locking: Within irq hander or disable_irq+spin_lock(&np->lock);
*/
- ring_type rx_ring;
+ union ring_type rx_ring;
unsigned int cur_rx, refill_rx;
struct sk_buff **rx_skbuff;
dma_addr_t *rx_dma;
@@ -733,7 +740,7 @@
/*
* tx specific fields.
*/
- ring_type tx_ring;
+ union ring_type tx_ring;
unsigned int next_tx, nic_tx;
struct sk_buff **tx_skbuff;
dma_addr_t *tx_dma;
@@ -826,13 +833,13 @@
static inline u32 nv_descr_getlength(struct ring_desc *prd, u32 v)
{
- return le32_to_cpu(prd->FlagLen)
+ return le32_to_cpu(prd->flaglen)
& ((v == DESC_VER_1) ? LEN_MASK_V1 : LEN_MASK_V2);
}
static inline u32 nv_descr_getlength_ex(struct ring_desc_ex *prd, u32 v)
{
- return le32_to_cpu(prd->FlagLen) & LEN_MASK_V2;
+ return le32_to_cpu(prd->flaglen) & LEN_MASK_V2;
}
static int reg_delay(struct net_device *dev, int offset, u32 mask, u32 target,
@@ -885,7 +892,7 @@
struct fe_priv *np = get_nvpriv(dev);
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- if(np->rx_ring.orig)
+ if (np->rx_ring.orig)
pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (np->rx_ring_size + np->tx_ring_size),
np->rx_ring.orig, np->ring_addr);
} else {
@@ -1178,7 +1185,7 @@
KERN_INFO "nv_stop_tx: TransmitterStatus remained busy");
udelay(NV_TXSTOP_DELAY2);
- writel(0, base + NvRegUnknownTransmitterReg);
+ writel(readl(base + NvRegTransmitPoll) & NVREG_TRANSMITPOLL_MAC_ADDR_REV, base + NvRegTransmitPoll);
}
static void nv_txrx_reset(struct net_device *dev)
@@ -1258,14 +1265,14 @@
np->rx_dma[nr] = pci_map_single(np->pci_dev, skb->data,
skb->end-skb->data, PCI_DMA_FROMDEVICE);
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->rx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->rx_dma[nr]);
+ np->rx_ring.orig[nr].buf = cpu_to_le32(np->rx_dma[nr]);
wmb();
- np->rx_ring.orig[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL);
+ np->rx_ring.orig[nr].flaglen = cpu_to_le32(np->rx_buf_sz | NV_RX_AVAIL);
} else {
- np->rx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->rx_dma[nr]) >> 32;
- np->rx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->rx_dma[nr]) & 0x0FFFFFFFF;
+ np->rx_ring.ex[nr].bufhigh = cpu_to_le64(np->rx_dma[nr]) >> 32;
+ np->rx_ring.ex[nr].buflow = cpu_to_le64(np->rx_dma[nr]) & 0x0FFFFFFFF;
wmb();
- np->rx_ring.ex[nr].FlagLen = cpu_to_le32(np->rx_buf_sz | NV_RX2_AVAIL);
+ np->rx_ring.ex[nr].flaglen = cpu_to_le32(np->rx_buf_sz | NV_RX2_AVAIL);
}
dprintk(KERN_DEBUG "%s: nv_alloc_rx: Packet %d marked as Available\n",
dev->name, refill_rx);
@@ -1277,6 +1284,16 @@
return 0;
}
+/* If rx bufs are exhausted called after 50ms to attempt to refresh */
+#ifdef CONFIG_FORCEDETH_NAPI
+static void nv_do_rx_refill(unsigned long data)
+{
+ struct net_device *dev = (struct net_device *) data;
+
+ /* Just reschedule NAPI rx processing */
+ netif_rx_schedule(dev);
+}
+#else
static void nv_do_rx_refill(unsigned long data)
{
struct net_device *dev = (struct net_device *) data;
@@ -1305,6 +1322,7 @@
enable_irq(np->msi_x_entry[NV_MSI_X_VECTOR_RX].vector);
}
}
+#endif
static void nv_init_rx(struct net_device *dev)
{
@@ -1315,9 +1333,9 @@
np->refill_rx = 0;
for (i = 0; i < np->rx_ring_size; i++)
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
- np->rx_ring.orig[i].FlagLen = 0;
+ np->rx_ring.orig[i].flaglen = 0;
else
- np->rx_ring.ex[i].FlagLen = 0;
+ np->rx_ring.ex[i].flaglen = 0;
}
static void nv_init_tx(struct net_device *dev)
@@ -1328,9 +1346,9 @@
np->next_tx = np->nic_tx = 0;
for (i = 0; i < np->tx_ring_size; i++) {
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
- np->tx_ring.orig[i].FlagLen = 0;
+ np->tx_ring.orig[i].flaglen = 0;
else
- np->tx_ring.ex[i].FlagLen = 0;
+ np->tx_ring.ex[i].flaglen = 0;
np->tx_skbuff[i] = NULL;
np->tx_dma[i] = 0;
}
@@ -1373,9 +1391,9 @@
for (i = 0; i < np->tx_ring_size; i++) {
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
- np->tx_ring.orig[i].FlagLen = 0;
+ np->tx_ring.orig[i].flaglen = 0;
else
- np->tx_ring.ex[i].FlagLen = 0;
+ np->tx_ring.ex[i].flaglen = 0;
if (nv_release_txskb(dev, i))
np->stats.tx_dropped++;
}
@@ -1387,9 +1405,9 @@
int i;
for (i = 0; i < np->rx_ring_size; i++) {
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
- np->rx_ring.orig[i].FlagLen = 0;
+ np->rx_ring.orig[i].flaglen = 0;
else
- np->rx_ring.ex[i].FlagLen = 0;
+ np->rx_ring.ex[i].flaglen = 0;
wmb();
if (np->rx_skbuff[i]) {
pci_unmap_single(np->pci_dev, np->rx_dma[i],
@@ -1450,17 +1468,17 @@
np->tx_dma_len[nr] = bcnt;
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->tx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]);
- np->tx_ring.orig[nr].FlagLen = cpu_to_le32((bcnt-1) | tx_flags);
+ np->tx_ring.orig[nr].buf = cpu_to_le32(np->tx_dma[nr]);
+ np->tx_ring.orig[nr].flaglen = cpu_to_le32((bcnt-1) | tx_flags);
} else {
- np->tx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->tx_dma[nr]) >> 32;
- np->tx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF;
- np->tx_ring.ex[nr].FlagLen = cpu_to_le32((bcnt-1) | tx_flags);
+ np->tx_ring.ex[nr].bufhigh = cpu_to_le64(np->tx_dma[nr]) >> 32;
+ np->tx_ring.ex[nr].buflow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF;
+ np->tx_ring.ex[nr].flaglen = cpu_to_le32((bcnt-1) | tx_flags);
}
tx_flags = np->tx_flags;
offset += bcnt;
size -= bcnt;
- } while(size);
+ } while (size);
/* setup the fragments */
for (i = 0; i < fragments; i++) {
@@ -1477,12 +1495,12 @@
np->tx_dma_len[nr] = bcnt;
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->tx_ring.orig[nr].PacketBuffer = cpu_to_le32(np->tx_dma[nr]);
- np->tx_ring.orig[nr].FlagLen = cpu_to_le32((bcnt-1) | tx_flags);
+ np->tx_ring.orig[nr].buf = cpu_to_le32(np->tx_dma[nr]);
+ np->tx_ring.orig[nr].flaglen = cpu_to_le32((bcnt-1) | tx_flags);
} else {
- np->tx_ring.ex[nr].PacketBufferHigh = cpu_to_le64(np->tx_dma[nr]) >> 32;
- np->tx_ring.ex[nr].PacketBufferLow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF;
- np->tx_ring.ex[nr].FlagLen = cpu_to_le32((bcnt-1) | tx_flags);
+ np->tx_ring.ex[nr].bufhigh = cpu_to_le64(np->tx_dma[nr]) >> 32;
+ np->tx_ring.ex[nr].buflow = cpu_to_le64(np->tx_dma[nr]) & 0x0FFFFFFFF;
+ np->tx_ring.ex[nr].flaglen = cpu_to_le32((bcnt-1) | tx_flags);
}
offset += bcnt;
size -= bcnt;
@@ -1491,9 +1509,9 @@
/* set last fragment flag */
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->tx_ring.orig[nr].FlagLen |= cpu_to_le32(tx_flags_extra);
+ np->tx_ring.orig[nr].flaglen |= cpu_to_le32(tx_flags_extra);
} else {
- np->tx_ring.ex[nr].FlagLen |= cpu_to_le32(tx_flags_extra);
+ np->tx_ring.ex[nr].flaglen |= cpu_to_le32(tx_flags_extra);
}
np->tx_skbuff[nr] = skb;
@@ -1512,10 +1530,10 @@
/* set tx flags */
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->tx_ring.orig[start_nr].FlagLen |= cpu_to_le32(tx_flags | tx_flags_extra);
+ np->tx_ring.orig[start_nr].flaglen |= cpu_to_le32(tx_flags | tx_flags_extra);
} else {
- np->tx_ring.ex[start_nr].TxVlan = cpu_to_le32(tx_flags_vlan);
- np->tx_ring.ex[start_nr].FlagLen |= cpu_to_le32(tx_flags | tx_flags_extra);
+ np->tx_ring.ex[start_nr].txvlan = cpu_to_le32(tx_flags_vlan);
+ np->tx_ring.ex[start_nr].flaglen |= cpu_to_le32(tx_flags | tx_flags_extra);
}
dprintk(KERN_DEBUG "%s: nv_start_xmit: packet %d (entries %d) queued for transmission. tx_flags_extra: %x\n",
@@ -1547,7 +1565,7 @@
static void nv_tx_done(struct net_device *dev)
{
struct fe_priv *np = netdev_priv(dev);
- u32 Flags;
+ u32 flags;
unsigned int i;
struct sk_buff *skb;
@@ -1555,22 +1573,22 @@
i = np->nic_tx % np->tx_ring_size;
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2)
- Flags = le32_to_cpu(np->tx_ring.orig[i].FlagLen);
+ flags = le32_to_cpu(np->tx_ring.orig[i].flaglen);
else
- Flags = le32_to_cpu(np->tx_ring.ex[i].FlagLen);
+ flags = le32_to_cpu(np->tx_ring.ex[i].flaglen);
- dprintk(KERN_DEBUG "%s: nv_tx_done: looking at packet %d, Flags 0x%x.\n",
- dev->name, np->nic_tx, Flags);
- if (Flags & NV_TX_VALID)
+ dprintk(KERN_DEBUG "%s: nv_tx_done: looking at packet %d, flags 0x%x.\n",
+ dev->name, np->nic_tx, flags);
+ if (flags & NV_TX_VALID)
break;
if (np->desc_ver == DESC_VER_1) {
- if (Flags & NV_TX_LASTPACKET) {
+ if (flags & NV_TX_LASTPACKET) {
skb = np->tx_skbuff[i];
- if (Flags & (NV_TX_RETRYERROR|NV_TX_CARRIERLOST|NV_TX_LATECOLLISION|
+ if (flags & (NV_TX_RETRYERROR|NV_TX_CARRIERLOST|NV_TX_LATECOLLISION|
NV_TX_UNDERFLOW|NV_TX_ERROR)) {
- if (Flags & NV_TX_UNDERFLOW)
+ if (flags & NV_TX_UNDERFLOW)
np->stats.tx_fifo_errors++;
- if (Flags & NV_TX_CARRIERLOST)
+ if (flags & NV_TX_CARRIERLOST)
np->stats.tx_carrier_errors++;
np->stats.tx_errors++;
} else {
@@ -1579,13 +1597,13 @@
}
}
} else {
- if (Flags & NV_TX2_LASTPACKET) {
+ if (flags & NV_TX2_LASTPACKET) {
skb = np->tx_skbuff[i];
- if (Flags & (NV_TX2_RETRYERROR|NV_TX2_CARRIERLOST|NV_TX2_LATECOLLISION|
+ if (flags & (NV_TX2_RETRYERROR|NV_TX2_CARRIERLOST|NV_TX2_LATECOLLISION|
NV_TX2_UNDERFLOW|NV_TX2_ERROR)) {
- if (Flags & NV_TX2_UNDERFLOW)
+ if (flags & NV_TX2_UNDERFLOW)
np->stats.tx_fifo_errors++;
- if (Flags & NV_TX2_CARRIERLOST)
+ if (flags & NV_TX2_CARRIERLOST)
np->stats.tx_carrier_errors++;
np->stats.tx_errors++;
} else {
@@ -1638,29 +1656,29 @@
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
printk(KERN_INFO "%03x: %08x %08x // %08x %08x // %08x %08x // %08x %08x\n",
i,
- le32_to_cpu(np->tx_ring.orig[i].PacketBuffer),
- le32_to_cpu(np->tx_ring.orig[i].FlagLen),
- le32_to_cpu(np->tx_ring.orig[i+1].PacketBuffer),
- le32_to_cpu(np->tx_ring.orig[i+1].FlagLen),
- le32_to_cpu(np->tx_ring.orig[i+2].PacketBuffer),
- le32_to_cpu(np->tx_ring.orig[i+2].FlagLen),
- le32_to_cpu(np->tx_ring.orig[i+3].PacketBuffer),
- le32_to_cpu(np->tx_ring.orig[i+3].FlagLen));
+ le32_to_cpu(np->tx_ring.orig[i].buf),
+ le32_to_cpu(np->tx_ring.orig[i].flaglen),
+ le32_to_cpu(np->tx_ring.orig[i+1].buf),
+ le32_to_cpu(np->tx_ring.orig[i+1].flaglen),
+ le32_to_cpu(np->tx_ring.orig[i+2].buf),
+ le32_to_cpu(np->tx_ring.orig[i+2].flaglen),
+ le32_to_cpu(np->tx_ring.orig[i+3].buf),
+ le32_to_cpu(np->tx_ring.orig[i+3].flaglen));
} else {
printk(KERN_INFO "%03x: %08x %08x %08x // %08x %08x %08x // %08x %08x %08x // %08x %08x %08x\n",
i,
- le32_to_cpu(np->tx_ring.ex[i].PacketBufferHigh),
- le32_to_cpu(np->tx_ring.ex[i].PacketBufferLow),
- le32_to_cpu(np->tx_ring.ex[i].FlagLen),
- le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferHigh),
- le32_to_cpu(np->tx_ring.ex[i+1].PacketBufferLow),
- le32_to_cpu(np->tx_ring.ex[i+1].FlagLen),
- le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferHigh),
- le32_to_cpu(np->tx_ring.ex[i+2].PacketBufferLow),
- le32_to_cpu(np->tx_ring.ex[i+2].FlagLen),
- le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferHigh),
- le32_to_cpu(np->tx_ring.ex[i+3].PacketBufferLow),
- le32_to_cpu(np->tx_ring.ex[i+3].FlagLen));
+ le32_to_cpu(np->tx_ring.ex[i].bufhigh),
+ le32_to_cpu(np->tx_ring.ex[i].buflow),
+ le32_to_cpu(np->tx_ring.ex[i].flaglen),
+ le32_to_cpu(np->tx_ring.ex[i+1].bufhigh),
+ le32_to_cpu(np->tx_ring.ex[i+1].buflow),
+ le32_to_cpu(np->tx_ring.ex[i+1].flaglen),
+ le32_to_cpu(np->tx_ring.ex[i+2].bufhigh),
+ le32_to_cpu(np->tx_ring.ex[i+2].buflow),
+ le32_to_cpu(np->tx_ring.ex[i+2].flaglen),
+ le32_to_cpu(np->tx_ring.ex[i+3].bufhigh),
+ le32_to_cpu(np->tx_ring.ex[i+3].buflow),
+ le32_to_cpu(np->tx_ring.ex[i+3].flaglen));
}
}
}
@@ -1697,7 +1715,7 @@
int protolen; /* length as stored in the proto field */
/* 1) calculate len according to header */
- if ( ((struct vlan_ethhdr *)packet)->h_vlan_proto == __constant_htons(ETH_P_8021Q)) {
+ if ( ((struct vlan_ethhdr *)packet)->h_vlan_proto == htons(ETH_P_8021Q)) {
protolen = ntohs( ((struct vlan_ethhdr *)packet)->h_vlan_encapsulated_proto );
hdrlen = VLAN_HLEN;
} else {
@@ -1740,13 +1758,14 @@
}
}
-static void nv_rx_process(struct net_device *dev)
+static int nv_rx_process(struct net_device *dev, int limit)
{
struct fe_priv *np = netdev_priv(dev);
- u32 Flags;
+ u32 flags;
u32 vlanflags = 0;
+ int count;
- for (;;) {
+ for (count = 0; count < limit; ++count) {
struct sk_buff *skb;
int len;
int i;
@@ -1755,18 +1774,18 @@
i = np->cur_rx % np->rx_ring_size;
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- Flags = le32_to_cpu(np->rx_ring.orig[i].FlagLen);
+ flags = le32_to_cpu(np->rx_ring.orig[i].flaglen);
len = nv_descr_getlength(&np->rx_ring.orig[i], np->desc_ver);
} else {
- Flags = le32_to_cpu(np->rx_ring.ex[i].FlagLen);
+ flags = le32_to_cpu(np->rx_ring.ex[i].flaglen);
len = nv_descr_getlength_ex(&np->rx_ring.ex[i], np->desc_ver);
- vlanflags = le32_to_cpu(np->rx_ring.ex[i].PacketBufferLow);
+ vlanflags = le32_to_cpu(np->rx_ring.ex[i].buflow);
}
- dprintk(KERN_DEBUG "%s: nv_rx_process: looking at packet %d, Flags 0x%x.\n",
- dev->name, np->cur_rx, Flags);
+ dprintk(KERN_DEBUG "%s: nv_rx_process: looking at packet %d, flags 0x%x.\n",
+ dev->name, np->cur_rx, flags);
- if (Flags & NV_RX_AVAIL)
+ if (flags & NV_RX_AVAIL)
break; /* still owned by hardware, */
/*
@@ -1780,7 +1799,7 @@
{
int j;
- dprintk(KERN_DEBUG "Dumping packet (flags 0x%x).",Flags);
+ dprintk(KERN_DEBUG "Dumping packet (flags 0x%x).",flags);
for (j=0; j<64; j++) {
if ((j%16) == 0)
dprintk("\n%03x:", j);
@@ -1790,30 +1809,30 @@
}
/* look at what we actually got: */
if (np->desc_ver == DESC_VER_1) {
- if (!(Flags & NV_RX_DESCRIPTORVALID))
+ if (!(flags & NV_RX_DESCRIPTORVALID))
goto next_pkt;
- if (Flags & NV_RX_ERROR) {
- if (Flags & NV_RX_MISSEDFRAME) {
+ if (flags & NV_RX_ERROR) {
+ if (flags & NV_RX_MISSEDFRAME) {
np->stats.rx_missed_errors++;
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & (NV_RX_ERROR1|NV_RX_ERROR2|NV_RX_ERROR3)) {
+ if (flags & (NV_RX_ERROR1|NV_RX_ERROR2|NV_RX_ERROR3)) {
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX_CRCERR) {
+ if (flags & NV_RX_CRCERR) {
np->stats.rx_crc_errors++;
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX_OVERFLOW) {
+ if (flags & NV_RX_OVERFLOW) {
np->stats.rx_over_errors++;
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX_ERROR4) {
+ if (flags & NV_RX_ERROR4) {
len = nv_getlen(dev, np->rx_skbuff[i]->data, len);
if (len < 0) {
np->stats.rx_errors++;
@@ -1821,32 +1840,32 @@
}
}
/* framing errors are soft errors. */
- if (Flags & NV_RX_FRAMINGERR) {
- if (Flags & NV_RX_SUBSTRACT1) {
+ if (flags & NV_RX_FRAMINGERR) {
+ if (flags & NV_RX_SUBSTRACT1) {
len--;
}
}
}
} else {
- if (!(Flags & NV_RX2_DESCRIPTORVALID))
+ if (!(flags & NV_RX2_DESCRIPTORVALID))
goto next_pkt;
- if (Flags & NV_RX2_ERROR) {
- if (Flags & (NV_RX2_ERROR1|NV_RX2_ERROR2|NV_RX2_ERROR3)) {
+ if (flags & NV_RX2_ERROR) {
+ if (flags & (NV_RX2_ERROR1|NV_RX2_ERROR2|NV_RX2_ERROR3)) {
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX2_CRCERR) {
+ if (flags & NV_RX2_CRCERR) {
np->stats.rx_crc_errors++;
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX2_OVERFLOW) {
+ if (flags & NV_RX2_OVERFLOW) {
np->stats.rx_over_errors++;
np->stats.rx_errors++;
goto next_pkt;
}
- if (Flags & NV_RX2_ERROR4) {
+ if (flags & NV_RX2_ERROR4) {
len = nv_getlen(dev, np->rx_skbuff[i]->data, len);
if (len < 0) {
np->stats.rx_errors++;
@@ -1854,17 +1873,17 @@
}
}
/* framing errors are soft errors */
- if (Flags & NV_RX2_FRAMINGERR) {
- if (Flags & NV_RX2_SUBSTRACT1) {
+ if (flags & NV_RX2_FRAMINGERR) {
+ if (flags & NV_RX2_SUBSTRACT1) {
len--;
}
}
}
if (np->txrxctl_bits & NVREG_TXRXCTL_RXCHECK) {
- Flags &= NV_RX2_CHECKSUMMASK;
- if (Flags == NV_RX2_CHECKSUMOK1 ||
- Flags == NV_RX2_CHECKSUMOK2 ||
- Flags == NV_RX2_CHECKSUMOK3) {
+ flags &= NV_RX2_CHECKSUMMASK;
+ if (flags == NV_RX2_CHECKSUMOK1 ||
+ flags == NV_RX2_CHECKSUMOK2 ||
+ flags == NV_RX2_CHECKSUMOK3) {
dprintk(KERN_DEBUG "%s: hw checksum hit!.\n", dev->name);
np->rx_skbuff[i]->ip_summed = CHECKSUM_UNNECESSARY;
} else {
@@ -1880,17 +1899,27 @@
skb->protocol = eth_type_trans(skb, dev);
dprintk(KERN_DEBUG "%s: nv_rx_process: packet %d with %d bytes, proto %d accepted.\n",
dev->name, np->cur_rx, len, skb->protocol);
- if (np->vlangrp && (vlanflags & NV_RX3_VLAN_TAG_PRESENT)) {
- vlan_hwaccel_rx(skb, np->vlangrp, vlanflags & NV_RX3_VLAN_TAG_MASK);
- } else {
+#ifdef CONFIG_FORCEDETH_NAPI
+ if (np->vlangrp && (vlanflags & NV_RX3_VLAN_TAG_PRESENT))
+ vlan_hwaccel_receive_skb(skb, np->vlangrp,
+ vlanflags & NV_RX3_VLAN_TAG_MASK);
+ else
+ netif_receive_skb(skb);
+#else
+ if (np->vlangrp && (vlanflags & NV_RX3_VLAN_TAG_PRESENT))
+ vlan_hwaccel_rx(skb, np->vlangrp,
+ vlanflags & NV_RX3_VLAN_TAG_MASK);
+ else
netif_rx(skb);
- }
+#endif
dev->last_rx = jiffies;
np->stats.rx_packets++;
np->stats.rx_bytes += len;
next_pkt:
np->cur_rx++;
}
+
+ return count;
}
static void set_bufsize(struct net_device *dev)
@@ -1990,7 +2019,7 @@
struct fe_priv *np = netdev_priv(dev);
struct sockaddr *macaddr = (struct sockaddr*)addr;
- if(!is_valid_ether_addr(macaddr->sa_data))
+ if (!is_valid_ether_addr(macaddr->sa_data))
return -EADDRNOTAVAIL;
/* synchronized against open : rtnl_lock() held by caller */
@@ -2283,20 +2312,20 @@
lpa_pause = lpa & (LPA_PAUSE_CAP| LPA_PAUSE_ASYM);
switch (adv_pause) {
- case (ADVERTISE_PAUSE_CAP):
+ case ADVERTISE_PAUSE_CAP:
if (lpa_pause & LPA_PAUSE_CAP) {
pause_flags |= NV_PAUSEFRAME_RX_ENABLE;
if (np->pause_flags & NV_PAUSEFRAME_TX_REQ)
pause_flags |= NV_PAUSEFRAME_TX_ENABLE;
}
break;
- case (ADVERTISE_PAUSE_ASYM):
+ case ADVERTISE_PAUSE_ASYM:
if (lpa_pause == (LPA_PAUSE_CAP| LPA_PAUSE_ASYM))
{
pause_flags |= NV_PAUSEFRAME_TX_ENABLE;
}
break;
- case (ADVERTISE_PAUSE_CAP| ADVERTISE_PAUSE_ASYM):
+ case ADVERTISE_PAUSE_CAP| ADVERTISE_PAUSE_ASYM:
if (lpa_pause & LPA_PAUSE_CAP)
{
pause_flags |= NV_PAUSEFRAME_RX_ENABLE;
@@ -2376,14 +2405,6 @@
nv_tx_done(dev);
spin_unlock(&np->lock);
- nv_rx_process(dev);
- if (nv_alloc_rx(dev)) {
- spin_lock(&np->lock);
- if (!np->in_shutdown)
- mod_timer(&np->oom_kick, jiffies + OOM_REFILL);
- spin_unlock(&np->lock);
- }
-
if (events & NVREG_IRQ_LINK) {
spin_lock(&np->lock);
nv_link_irq(dev);
@@ -2403,6 +2424,29 @@
printk(KERN_DEBUG "%s: received irq with unknown events 0x%x. Please report\n",
dev->name, events);
}
+#ifdef CONFIG_FORCEDETH_NAPI
+ if (events & NVREG_IRQ_RX_ALL) {
+ netif_rx_schedule(dev);
+
+ /* Disable furthur receive irq's */
+ spin_lock(&np->lock);
+ np->irqmask &= ~NVREG_IRQ_RX_ALL;
+
+ if (np->msi_flags & NV_MSI_X_ENABLED)
+ writel(NVREG_IRQ_RX_ALL, base + NvRegIrqMask);
+ else
+ writel(np->irqmask, base + NvRegIrqMask);
+ spin_unlock(&np->lock);
+ }
+#else
+ nv_rx_process(dev, dev->weight);
+ if (nv_alloc_rx(dev)) {
+ spin_lock(&np->lock);
+ if (!np->in_shutdown)
+ mod_timer(&np->oom_kick, jiffies + OOM_REFILL);
+ spin_unlock(&np->lock);
+ }
+#endif
if (i > max_interrupt_work) {
spin_lock(&np->lock);
/* disable interrupts on the nic */
@@ -2474,6 +2518,63 @@
return IRQ_RETVAL(i);
}
+#ifdef CONFIG_FORCEDETH_NAPI
+static int nv_napi_poll(struct net_device *dev, int *budget)
+{
+ int pkts, limit = min(*budget, dev->quota);
+ struct fe_priv *np = netdev_priv(dev);
+ u8 __iomem *base = get_hwbase(dev);
+
+ pkts = nv_rx_process(dev, limit);
+
+ if (nv_alloc_rx(dev)) {
+ spin_lock_irq(&np->lock);
+ if (!np->in_shutdown)
+ mod_timer(&np->oom_kick, jiffies + OOM_REFILL);
+ spin_unlock_irq(&np->lock);
+ }
+
+ if (pkts < limit) {
+ /* all done, no more packets present */
+ netif_rx_complete(dev);
+
+ /* re-enable receive interrupts */
+ spin_lock_irq(&np->lock);
+ np->irqmask |= NVREG_IRQ_RX_ALL;
+ if (np->msi_flags & NV_MSI_X_ENABLED)
+ writel(NVREG_IRQ_RX_ALL, base + NvRegIrqMask);
+ else
+ writel(np->irqmask, base + NvRegIrqMask);
+ spin_unlock_irq(&np->lock);
+ return 0;
+ } else {
+ /* used up our quantum, so reschedule */
+ dev->quota -= pkts;
+ *budget -= pkts;
+ return 1;
+ }
+}
+#endif
+
+#ifdef CONFIG_FORCEDETH_NAPI
+static irqreturn_t nv_nic_irq_rx(int foo, void *data, struct pt_regs *regs)
+{
+ struct net_device *dev = (struct net_device *) data;
+ u8 __iomem *base = get_hwbase(dev);
+ u32 events;
+
+ events = readl(base + NvRegMSIXIrqStatus) & NVREG_IRQ_RX_ALL;
+ writel(NVREG_IRQ_RX_ALL, base + NvRegMSIXIrqStatus);
+
+ if (events) {
+ netif_rx_schedule(dev);
+ /* disable receive interrupts on the nic */
+ writel(NVREG_IRQ_RX_ALL, base + NvRegIrqMask);
+ pci_push(base);
+ }
+ return IRQ_HANDLED;
+}
+#else
static irqreturn_t nv_nic_irq_rx(int foo, void *data, struct pt_regs *regs)
{
struct net_device *dev = (struct net_device *) data;
@@ -2492,7 +2593,7 @@
if (!(events & np->irqmask))
break;
- nv_rx_process(dev);
+ nv_rx_process(dev, dev->weight);
if (nv_alloc_rx(dev)) {
spin_lock_irq(&np->lock);
if (!np->in_shutdown)
@@ -2514,12 +2615,12 @@
spin_unlock_irq(&np->lock);
break;
}
-
}
dprintk(KERN_DEBUG "%s: nv_nic_irq_rx completed\n", dev->name);
return IRQ_RETVAL(i);
}
+#endif
static irqreturn_t nv_nic_irq_other(int foo, void *data, struct pt_regs *regs)
{
@@ -3245,7 +3346,7 @@
if (!rxtx_ring || !rx_skbuff || !rx_dma || !tx_skbuff || !tx_dma || !tx_dma_len) {
/* fall back to old rings */
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- if(rxtx_ring)
+ if (rxtx_ring)
pci_free_consistent(np->pci_dev, sizeof(struct ring_desc) * (ring->rx_pending + ring->tx_pending),
rxtx_ring, ring_addr);
} else {
@@ -3481,7 +3582,7 @@
struct fe_priv *np = netdev_priv(dev);
if (np->driver_data & DEV_HAS_STATISTICS)
- return (sizeof(struct nv_ethtool_stats)/sizeof(u64));
+ return sizeof(struct nv_ethtool_stats)/sizeof(u64);
else
return 0;
}
@@ -3619,7 +3720,7 @@
struct sk_buff *tx_skb, *rx_skb;
dma_addr_t test_dma_addr;
u32 tx_flags_extra = (np->desc_ver == DESC_VER_1 ? NV_TX_LASTPACKET : NV_TX2_LASTPACKET);
- u32 Flags;
+ u32 flags;
int len, i, pkt_len;
u8 *pkt_data;
u32 filter_flags = 0;
@@ -3663,12 +3764,12 @@
tx_skb->end-tx_skb->data, PCI_DMA_FROMDEVICE);
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- np->tx_ring.orig[0].PacketBuffer = cpu_to_le32(test_dma_addr);
- np->tx_ring.orig[0].FlagLen = cpu_to_le32((pkt_len-1) | np->tx_flags | tx_flags_extra);
+ np->tx_ring.orig[0].buf = cpu_to_le32(test_dma_addr);
+ np->tx_ring.orig[0].flaglen = cpu_to_le32((pkt_len-1) | np->tx_flags | tx_flags_extra);
} else {
- np->tx_ring.ex[0].PacketBufferHigh = cpu_to_le64(test_dma_addr) >> 32;
- np->tx_ring.ex[0].PacketBufferLow = cpu_to_le64(test_dma_addr) & 0x0FFFFFFFF;
- np->tx_ring.ex[0].FlagLen = cpu_to_le32((pkt_len-1) | np->tx_flags | tx_flags_extra);
+ np->tx_ring.ex[0].bufhigh = cpu_to_le64(test_dma_addr) >> 32;
+ np->tx_ring.ex[0].buflow = cpu_to_le64(test_dma_addr) & 0x0FFFFFFFF;
+ np->tx_ring.ex[0].flaglen = cpu_to_le32((pkt_len-1) | np->tx_flags | tx_flags_extra);
}
writel(NVREG_TXRXCTL_KICK|np->txrxctl_bits, get_hwbase(dev) + NvRegTxRxControl);
pci_push(get_hwbase(dev));
@@ -3677,21 +3778,21 @@
/* check for rx of the packet */
if (np->desc_ver == DESC_VER_1 || np->desc_ver == DESC_VER_2) {
- Flags = le32_to_cpu(np->rx_ring.orig[0].FlagLen);
+ flags = le32_to_cpu(np->rx_ring.orig[0].flaglen);
len = nv_descr_getlength(&np->rx_ring.orig[0], np->desc_ver);
} else {
- Flags = le32_to_cpu(np->rx_ring.ex[0].FlagLen);
+ flags = le32_to_cpu(np->rx_ring.ex[0].flaglen);
len = nv_descr_getlength_ex(&np->rx_ring.ex[0], np->desc_ver);
}
- if (Flags & NV_RX_AVAIL) {
+ if (flags & NV_RX_AVAIL) {
ret = 0;
} else if (np->desc_ver == DESC_VER_1) {
- if (Flags & NV_RX_ERROR)
+ if (flags & NV_RX_ERROR)
ret = 0;
} else {
- if (Flags & NV_RX2_ERROR) {
+ if (flags & NV_RX2_ERROR) {
ret = 0;
}
}
@@ -3753,6 +3854,7 @@
if (test->flags & ETH_TEST_FL_OFFLINE) {
if (netif_running(dev)) {
netif_stop_queue(dev);
+ netif_poll_disable(dev);
netif_tx_lock_bh(dev);
spin_lock_irq(&np->lock);
nv_disable_hw_interrupts(dev, np->irqmask);
@@ -3811,6 +3913,7 @@
nv_start_rx(dev);
nv_start_tx(dev);
netif_start_queue(dev);
+ netif_poll_enable(dev);
nv_enable_hw_interrupts(dev, np->irqmask);
}
}
@@ -3895,10 +3998,9 @@
dprintk(KERN_DEBUG "nv_open: begin\n");
- /* 1) erase previous misconfiguration */
+ /* erase previous misconfiguration */
if (np->driver_data & DEV_HAS_POWER_CNTRL)
nv_mac_reset(dev);
- /* 4.1-1: stop adapter: ignored, 4.3 seems to be overkill */
writel(NVREG_MCASTADDRA_FORCE, base + NvRegMulticastAddrA);
writel(0, base + NvRegMulticastAddrB);
writel(0, base + NvRegMulticastMaskA);
@@ -3913,26 +4015,22 @@
if (np->pause_flags & NV_PAUSEFRAME_TX_CAPABLE)
writel(NVREG_TX_PAUSEFRAME_DISABLE, base + NvRegTxPauseFrame);
- /* 2) initialize descriptor rings */
+ /* initialize descriptor rings */
set_bufsize(dev);
oom = nv_init_ring(dev);
writel(0, base + NvRegLinkSpeed);
- writel(0, base + NvRegUnknownTransmitterReg);
+ writel(readl(base + NvRegTransmitPoll) & NVREG_TRANSMITPOLL_MAC_ADDR_REV, base + NvRegTransmitPoll);
nv_txrx_reset(dev);
writel(0, base + NvRegUnknownSetupReg6);
np->in_shutdown = 0;
- /* 3) set mac address */
- nv_copy_mac_to_hw(dev);
-
- /* 4) give hw rings */
+ /* give hw rings */
setup_hw_rings(dev, NV_SETUP_RX_RING | NV_SETUP_TX_RING);
writel( ((np->rx_ring_size-1) << NVREG_RINGSZ_RXSHIFT) + ((np->tx_ring_size-1) << NVREG_RINGSZ_TXSHIFT),
base + NvRegRingSizes);
- /* 5) continue setup */
writel(np->linkspeed, base + NvRegLinkSpeed);
if (np->desc_ver == DESC_VER_1)
writel(NVREG_TX_WM_DESC1_DEFAULT, base + NvRegTxWatermark);
@@ -3950,7 +4048,6 @@
writel(NVREG_IRQSTAT_MASK, base + NvRegIrqStatus);
writel(NVREG_MIISTAT_MASK2, base + NvRegMIIStatus);
- /* 6) continue setup */
writel(NVREG_MISC1_FORCE | NVREG_MISC1_HD, base + NvRegMisc1);
writel(readl(base + NvRegTransmitterStatus), base + NvRegTransmitterStatus);
writel(NVREG_PFF_ALWAYS, base + NvRegPacketFilterFlags);
@@ -4020,6 +4117,8 @@
nv_start_rx(dev);
nv_start_tx(dev);
netif_start_queue(dev);
+ netif_poll_enable(dev);
+
if (ret) {
netif_carrier_on(dev);
} else {
@@ -4049,6 +4148,7 @@
spin_lock_irq(&np->lock);
np->in_shutdown = 1;
spin_unlock_irq(&np->lock);
+ netif_poll_disable(dev);
synchronize_irq(dev->irq);
del_timer_sync(&np->oom_kick);
@@ -4076,12 +4176,6 @@
if (np->wolenabled)
nv_start_rx(dev);
- /* special op: write back the misordered MAC address - otherwise
- * the next nv_probe would see a wrong address.
- */
- writel(np->orig_mac[0], base + NvRegMacAddrA);
- writel(np->orig_mac[1], base + NvRegMacAddrB);
-
/* FIXME: power down nic */
return 0;
@@ -4094,7 +4188,7 @@
unsigned long addr;
u8 __iomem *base;
int err, i;
- u32 powerstate;
+ u32 powerstate, txreg;
dev = alloc_etherdev(sizeof(struct fe_priv));
err = -ENOMEM;
@@ -4270,6 +4364,10 @@
#ifdef CONFIG_NET_POLL_CONTROLLER
dev->poll_controller = nv_poll_controller;
#endif
+ dev->weight = 64;
+#ifdef CONFIG_FORCEDETH_NAPI
+ dev->poll = nv_napi_poll;
+#endif
SET_ETHTOOL_OPS(dev, &ops);
dev->tx_timeout = nv_tx_timeout;
dev->watchdog_timeo = NV_WATCHDOG_TIMEO;
@@ -4281,12 +4379,30 @@
np->orig_mac[0] = readl(base + NvRegMacAddrA);
np->orig_mac[1] = readl(base + NvRegMacAddrB);
- dev->dev_addr[0] = (np->orig_mac[1] >> 8) & 0xff;
- dev->dev_addr[1] = (np->orig_mac[1] >> 0) & 0xff;
- dev->dev_addr[2] = (np->orig_mac[0] >> 24) & 0xff;
- dev->dev_addr[3] = (np->orig_mac[0] >> 16) & 0xff;
- dev->dev_addr[4] = (np->orig_mac[0] >> 8) & 0xff;
- dev->dev_addr[5] = (np->orig_mac[0] >> 0) & 0xff;
+ /* check the workaround bit for correct mac address order */
+ txreg = readl(base + NvRegTransmitPoll);
+ if (txreg & NVREG_TRANSMITPOLL_MAC_ADDR_REV) {
+ /* mac address is already in correct order */
+ dev->dev_addr[0] = (np->orig_mac[0] >> 0) & 0xff;
+ dev->dev_addr[1] = (np->orig_mac[0] >> 8) & 0xff;
+ dev->dev_addr[2] = (np->orig_mac[0] >> 16) & 0xff;
+ dev->dev_addr[3] = (np->orig_mac[0] >> 24) & 0xff;
+ dev->dev_addr[4] = (np->orig_mac[1] >> 0) & 0xff;
+ dev->dev_addr[5] = (np->orig_mac[1] >> 8) & 0xff;
+ } else {
+ /* need to reverse mac address to correct order */
+ dev->dev_addr[0] = (np->orig_mac[1] >> 8) & 0xff;
+ dev->dev_addr[1] = (np->orig_mac[1] >> 0) & 0xff;
+ dev->dev_addr[2] = (np->orig_mac[0] >> 24) & 0xff;
+ dev->dev_addr[3] = (np->orig_mac[0] >> 16) & 0xff;
+ dev->dev_addr[4] = (np->orig_mac[0] >> 8) & 0xff;
+ dev->dev_addr[5] = (np->orig_mac[0] >> 0) & 0xff;
+ /* set permanent address to be correct aswell */
+ np->orig_mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) +
+ (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24);
+ np->orig_mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8);
+ writel(txreg|NVREG_TRANSMITPOLL_MAC_ADDR_REV, base + NvRegTransmitPoll);
+ }
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
if (!is_valid_ether_addr(dev->perm_addr)) {
@@ -4309,6 +4425,9 @@
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
+ /* set mac address */
+ nv_copy_mac_to_hw(dev);
+
/* disable WOL */
writel(0, base + NvRegWakeUpFlags);
np->wolenabled = 0;
@@ -4421,9 +4540,17 @@
static void __devexit nv_remove(struct pci_dev *pci_dev)
{
struct net_device *dev = pci_get_drvdata(pci_dev);
+ struct fe_priv *np = netdev_priv(dev);
+ u8 __iomem *base = get_hwbase(dev);
unregister_netdev(dev);
+ /* special op: write back the misordered MAC address - otherwise
+ * the next nv_probe would see a wrong address.
+ */
+ writel(np->orig_mac[0], base + NvRegMacAddrA);
+ writel(np->orig_mac[1], base + NvRegMacAddrB);
+
/* free all structures */
free_rings(dev);
iounmap(get_hwbase(dev));
@@ -4540,7 +4667,7 @@
static int __init init_nic(void)
{
printk(KERN_INFO "forcedeth.c: Reverse Engineered nForce ethernet driver. Version %s.\n", FORCEDETH_VERSION);
- return pci_module_init(&driver);
+ return pci_register_driver(&driver);
}
static void __exit exit_nic(void)
diff --git a/drivers/net/hp100.c b/drivers/net/hp100.c
index e7d9bf3..ff5a67d 100644
--- a/drivers/net/hp100.c
+++ b/drivers/net/hp100.c
@@ -111,7 +111,6 @@
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/types.h>
-#include <linux/config.h> /* for CONFIG_PCI */
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/bitops.h>
diff --git a/drivers/net/irda/mcs7780.c b/drivers/net/irda/mcs7780.c
index 47f6f64..415ba8d 100644
--- a/drivers/net/irda/mcs7780.c
+++ b/drivers/net/irda/mcs7780.c
@@ -45,7 +45,6 @@
#include <linux/module.h>
#include <linux/moduleparam.h>
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/errno.h>
diff --git a/drivers/net/irda/w83977af_ir.c b/drivers/net/irda/w83977af_ir.c
index 0ea65c4..b69776e 100644
--- a/drivers/net/irda/w83977af_ir.c
+++ b/drivers/net/irda/w83977af_ir.c
@@ -40,7 +40,6 @@
********************************************************************/
#include <linux/module.h>
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/skbuff.h>
diff --git a/drivers/net/ixgb/ixgb.h b/drivers/net/ixgb/ixgb.h
index 82b67af..a51604b 100644
--- a/drivers/net/ixgb/ixgb.h
+++ b/drivers/net/ixgb/ixgb.h
@@ -110,9 +110,6 @@
#define IXGB_RXBUFFER_8192 8192
#define IXGB_RXBUFFER_16384 16384
-/* How many Tx Descriptors do we need to call netif_wake_queue? */
-#define IXGB_TX_QUEUE_WAKE 16
-
/* How many Rx Buffers do we bundle into one write to the hardware ? */
#define IXGB_RX_BUFFER_WRITE 4 /* Must be power of 2 */
@@ -173,7 +170,7 @@
unsigned long led_status;
/* TX */
- struct ixgb_desc_ring tx_ring;
+ struct ixgb_desc_ring tx_ring ____cacheline_aligned_in_smp;
unsigned long timeo_start;
uint32_t tx_cmd_type;
uint64_t hw_csum_tx_good;
diff --git a/drivers/net/ixgb/ixgb_ethtool.c b/drivers/net/ixgb/ixgb_ethtool.c
index cf19b89..ba62108 100644
--- a/drivers/net/ixgb/ixgb_ethtool.c
+++ b/drivers/net/ixgb/ixgb_ethtool.c
@@ -654,11 +654,7 @@
mod_timer(&adapter->blink_timer, jiffies);
- if (data)
- schedule_timeout_interruptible(data * HZ);
- else
- schedule_timeout_interruptible(MAX_SCHEDULE_TIMEOUT);
-
+ msleep_interruptible(data * 1000);
del_timer_sync(&adapter->blink_timer);
ixgb_led_off(&adapter->hw);
clear_bit(IXGB_LED_ON, &adapter->led_status);
diff --git a/drivers/net/ixgb/ixgb_hw.c b/drivers/net/ixgb/ixgb_hw.c
index f7fa10e..2b15155 100644
--- a/drivers/net/ixgb/ixgb_hw.c
+++ b/drivers/net/ixgb/ixgb_hw.c
@@ -236,6 +236,17 @@
DEBUGOUT("Identified G6104 optics\n");
phy_type = ixgb_phy_type_g6104;
break;
+ case IXGB_DEVICE_ID_82597EX_CX4:
+ DEBUGOUT("Identified CX4\n");
+ xpak_vendor = ixgb_identify_xpak_vendor(hw);
+ if (xpak_vendor == ixgb_xpak_vendor_intel) {
+ DEBUGOUT("Identified TXN17201 optics\n");
+ phy_type = ixgb_phy_type_txn17201;
+ } else {
+ DEBUGOUT("Identified G6005 optics\n");
+ phy_type = ixgb_phy_type_g6005;
+ }
+ break;
default:
DEBUGOUT("Unknown physical layer module\n");
phy_type = ixgb_phy_type_unknown;
diff --git a/drivers/net/ixgb/ixgb_ids.h b/drivers/net/ixgb/ixgb_ids.h
index 40a085f..9fd6118 100644
--- a/drivers/net/ixgb/ixgb_ids.h
+++ b/drivers/net/ixgb/ixgb_ids.h
@@ -45,6 +45,7 @@
#define IXGB_DEVICE_ID_82597EX_CX4 0x109E
#define IXGB_SUBDEVICE_ID_A00C 0xA00C
+#define IXGB_SUBDEVICE_ID_A01C 0xA01C
#endif /* #ifndef _IXGB_IDS_H_ */
/* End of File */
diff --git a/drivers/net/ixgb/ixgb_main.c b/drivers/net/ixgb/ixgb_main.c
index 7bbd447..e36dee1 100644
--- a/drivers/net/ixgb/ixgb_main.c
+++ b/drivers/net/ixgb/ixgb_main.c
@@ -36,7 +36,7 @@
#else
#define DRIVERNAPI "-NAPI"
#endif
-#define DRV_VERSION "1.0.109-k2"DRIVERNAPI
+#define DRV_VERSION "1.0.112-k2"DRIVERNAPI
char ixgb_driver_version[] = DRV_VERSION;
static char ixgb_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
@@ -118,15 +118,26 @@
static void ixgb_netpoll(struct net_device *dev);
#endif
-/* Exported from other modules */
+static pci_ers_result_t ixgb_io_error_detected (struct pci_dev *pdev,
+ enum pci_channel_state state);
+static pci_ers_result_t ixgb_io_slot_reset (struct pci_dev *pdev);
+static void ixgb_io_resume (struct pci_dev *pdev);
+/* Exported from other modules */
extern void ixgb_check_options(struct ixgb_adapter *adapter);
+static struct pci_error_handlers ixgb_err_handler = {
+ .error_detected = ixgb_io_error_detected,
+ .slot_reset = ixgb_io_slot_reset,
+ .resume = ixgb_io_resume,
+};
+
static struct pci_driver ixgb_driver = {
.name = ixgb_driver_name,
.id_table = ixgb_pci_tbl,
.probe = ixgb_probe,
.remove = __devexit_p(ixgb_remove),
+ .err_handler = &ixgb_err_handler
};
MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
@@ -140,12 +151,12 @@
MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
/* some defines for controlling descriptor fetches in h/w */
-#define RXDCTL_WTHRESH_DEFAULT 16 /* chip writes back at this many or RXT0 */
-#define RXDCTL_PTHRESH_DEFAULT 0 /* chip considers prefech below
- * this */
-#define RXDCTL_HTHRESH_DEFAULT 0 /* chip will only prefetch if tail
- * is pushed this many descriptors
- * from head */
+#define RXDCTL_WTHRESH_DEFAULT 15 /* chip writes back at this many or RXT0 */
+#define RXDCTL_PTHRESH_DEFAULT 0 /* chip considers prefech below
+ * this */
+#define RXDCTL_HTHRESH_DEFAULT 0 /* chip will only prefetch if tail
+ * is pushed this many descriptors
+ * from head */
/**
* ixgb_init_module - Driver Registration Routine
@@ -162,7 +173,7 @@
printk(KERN_INFO "%s\n", ixgb_copyright);
- return pci_module_init(&ixgb_driver);
+ return pci_register_driver(&ixgb_driver);
}
module_init(ixgb_init_module);
@@ -1174,6 +1185,7 @@
int err;
if (likely(skb_is_gso(skb))) {
+ struct ixgb_buffer *buffer_info;
if (skb_header_cloned(skb)) {
err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
if (err)
@@ -1196,6 +1208,8 @@
i = adapter->tx_ring.next_to_use;
context_desc = IXGB_CONTEXT_DESC(adapter->tx_ring, i);
+ buffer_info = &adapter->tx_ring.buffer_info[i];
+ WARN_ON(buffer_info->dma != 0);
context_desc->ipcss = ipcss;
context_desc->ipcso = ipcso;
@@ -1233,11 +1247,14 @@
uint8_t css, cso;
if(likely(skb->ip_summed == CHECKSUM_HW)) {
+ struct ixgb_buffer *buffer_info;
css = skb->h.raw - skb->data;
cso = (skb->h.raw + skb->csum) - skb->data;
i = adapter->tx_ring.next_to_use;
context_desc = IXGB_CONTEXT_DESC(adapter->tx_ring, i);
+ buffer_info = &adapter->tx_ring.buffer_info[i];
+ WARN_ON(buffer_info->dma != 0);
context_desc->tucss = css;
context_desc->tucso = cso;
@@ -1283,6 +1300,7 @@
buffer_info = &tx_ring->buffer_info[i];
size = min(len, IXGB_MAX_DATA_PER_TXD);
buffer_info->length = size;
+ WARN_ON(buffer_info->dma != 0);
buffer_info->dma =
pci_map_single(adapter->pdev,
skb->data + offset,
@@ -1543,6 +1561,11 @@
ixgb_update_stats(struct ixgb_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
+ struct pci_dev *pdev = adapter->pdev;
+
+ /* Prevent stats update while adapter is being reset */
+ if (pdev->error_state && pdev->error_state != pci_channel_io_normal)
+ return;
if((netdev->flags & IFF_PROMISC) || (netdev->flags & IFF_ALLMULTI) ||
(netdev->mc_count > IXGB_MAX_NUM_MULTICAST_ADDRESSES)) {
@@ -1787,7 +1810,7 @@
if (unlikely(netif_queue_stopped(netdev))) {
spin_lock(&adapter->tx_lock);
if (netif_queue_stopped(netdev) && netif_carrier_ok(netdev) &&
- (IXGB_DESC_UNUSED(tx_ring) > IXGB_TX_QUEUE_WAKE))
+ (IXGB_DESC_UNUSED(tx_ring) >= DESC_NEEDED))
netif_wake_queue(netdev);
spin_unlock(&adapter->tx_lock);
}
@@ -1948,10 +1971,9 @@
#define IXGB_CB_LENGTH 256
if (length < IXGB_CB_LENGTH) {
struct sk_buff *new_skb =
- dev_alloc_skb(length + NET_IP_ALIGN);
+ netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
if (new_skb) {
skb_reserve(new_skb, NET_IP_ALIGN);
- new_skb->dev = netdev;
memcpy(new_skb->data - NET_IP_ALIGN,
skb->data - NET_IP_ALIGN,
length + NET_IP_ALIGN);
@@ -2031,14 +2053,14 @@
/* leave three descriptors unused */
while(--cleancount > 2) {
/* recycle! its good for you */
- if (!(skb = buffer_info->skb))
- skb = dev_alloc_skb(adapter->rx_buffer_len
- + NET_IP_ALIGN);
- else {
+ skb = buffer_info->skb;
+ if (skb) {
skb_trim(skb, 0);
goto map_skb;
}
+ skb = netdev_alloc_skb(netdev, adapter->rx_buffer_len
+ + NET_IP_ALIGN);
if (unlikely(!skb)) {
/* Better luck next round */
adapter->alloc_rx_buff_failed++;
@@ -2051,8 +2073,6 @@
*/
skb_reserve(skb, NET_IP_ALIGN);
- skb->dev = netdev;
-
buffer_info->skb = skb;
buffer_info->length = adapter->rx_buffer_len;
map_skb:
@@ -2190,7 +2210,7 @@
static void ixgb_netpoll(struct net_device *dev)
{
- struct ixgb_adapter *adapter = dev->priv;
+ struct ixgb_adapter *adapter = netdev_priv(dev);
disable_irq(adapter->pdev->irq);
ixgb_intr(adapter->pdev->irq, dev, NULL);
@@ -2198,4 +2218,98 @@
}
#endif
+/**
+ * ixgb_io_error_detected() - called when PCI error is detected
+ * @pdev pointer to pci device with error
+ * @state pci channel state after error
+ *
+ * This callback is called by the PCI subsystem whenever
+ * a PCI bus error is detected.
+ */
+static pci_ers_result_t ixgb_io_error_detected (struct pci_dev *pdev,
+ enum pci_channel_state state)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct ixgb_adapter *adapter = netdev->priv;
+
+ if(netif_running(netdev))
+ ixgb_down(adapter, TRUE);
+
+ pci_disable_device(pdev);
+
+ /* Request a slot reset. */
+ return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/**
+ * ixgb_io_slot_reset - called after the pci bus has been reset.
+ * @pdev pointer to pci device with error
+ *
+ * This callback is called after the PCI buss has been reset.
+ * Basically, this tries to restart the card from scratch.
+ * This is a shortened version of the device probe/discovery code,
+ * it resembles the first-half of the ixgb_probe() routine.
+ */
+static pci_ers_result_t ixgb_io_slot_reset (struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct ixgb_adapter *adapter = netdev->priv;
+
+ if(pci_enable_device(pdev)) {
+ DPRINTK(PROBE, ERR, "Cannot re-enable PCI device after reset.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+
+ /* Perform card reset only on one instance of the card */
+ if (0 != PCI_FUNC (pdev->devfn))
+ return PCI_ERS_RESULT_RECOVERED;
+
+ pci_set_master(pdev);
+
+ netif_carrier_off(netdev);
+ netif_stop_queue(netdev);
+ ixgb_reset(adapter);
+
+ /* Make sure the EEPROM is good */
+ if(!ixgb_validate_eeprom_checksum(&adapter->hw)) {
+ DPRINTK(PROBE, ERR, "After reset, the EEPROM checksum is not valid.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+ ixgb_get_ee_mac_addr(&adapter->hw, netdev->dev_addr);
+ memcpy(netdev->perm_addr, netdev->dev_addr, netdev->addr_len);
+
+ if(!is_valid_ether_addr(netdev->perm_addr)) {
+ DPRINTK(PROBE, ERR, "After reset, invalid MAC address.\n");
+ return PCI_ERS_RESULT_DISCONNECT;
+ }
+
+ return PCI_ERS_RESULT_RECOVERED;
+}
+
+/**
+ * ixgb_io_resume - called when its OK to resume normal operations
+ * @pdev pointer to pci device with error
+ *
+ * The error recovery driver tells us that its OK to resume
+ * normal operation. Implementation resembles the second-half
+ * of the ixgb_probe() routine.
+ */
+static void ixgb_io_resume (struct pci_dev *pdev)
+{
+ struct net_device *netdev = pci_get_drvdata(pdev);
+ struct ixgb_adapter *adapter = netdev->priv;
+
+ pci_set_master(pdev);
+
+ if(netif_running(netdev)) {
+ if(ixgb_up(adapter)) {
+ printk ("ixgb: can't bring device back up after reset\n");
+ return;
+ }
+ }
+
+ netif_device_attach(netdev);
+ mod_timer(&adapter->watchdog_timer, jiffies);
+}
+
/* ixgb_main.c */
diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c
index 9bdd43a..e2346e8 100644
--- a/drivers/net/myri10ge/myri10ge.c
+++ b/drivers/net/myri10ge/myri10ge.c
@@ -187,11 +187,14 @@
u8 mac_addr[6]; /* eeprom mac address */
unsigned long serial_number;
int vendor_specific_offset;
+ int fw_multicast_support;
u32 devctl;
u16 msi_flags;
u32 read_dma;
u32 write_dma;
u32 read_write_dma;
+ u32 link_changes;
+ u32 msg_enable;
};
static char *myri10ge_fw_unaligned = "myri10ge_ethp_z8e.dat";
@@ -257,6 +260,12 @@
MODULE_PARM_DESC(myri10ge_max_irq_loops,
"Set stuck legacy IRQ detection threshold\n");
+#define MYRI10GE_MSG_DEFAULT NETIF_MSG_LINK
+
+static int myri10ge_debug = -1; /* defaults above */
+module_param(myri10ge_debug, int, 0);
+MODULE_PARM_DESC(myri10ge_debug, "Debug level (0=none,...,16=all)");
+
#define MYRI10GE_FW_OFFSET 1024*1024
#define MYRI10GE_HIGHPART_TO_U32(X) \
(sizeof (X) == 8) ? ((u32)((u64)(X) >> 32)) : (0)
@@ -271,7 +280,7 @@
struct mcp_cmd *buf;
char buf_bytes[sizeof(*buf) + 8];
struct mcp_cmd_response *response = mgp->cmd;
- char __iomem *cmd_addr = mgp->sram + MXGEFW_CMD_OFFSET;
+ char __iomem *cmd_addr = mgp->sram + MXGEFW_ETH_CMD;
u32 dma_low, dma_high, result, value;
int sleep_total = 0;
@@ -320,6 +329,8 @@
if (result == 0) {
data->data0 = value;
return 0;
+ } else if (result == MXGEFW_CMD_UNKNOWN) {
+ return -ENOSYS;
} else {
dev_err(&mgp->pdev->dev,
"command %d failed, result = %d\n",
@@ -404,7 +415,7 @@
buf[4] = htonl(dma_low); /* dummy addr LSW */
buf[5] = htonl(enable); /* enable? */
- submit = mgp->sram + 0xfc01c0;
+ submit = mgp->sram + MXGEFW_BOOT_DUMMY_RDMA;
myri10ge_pio_copy(submit, &buf, sizeof(buf));
for (i = 0; mgp->cmd->data != MYRI10GE_NO_CONFIRM_DATA && i < 20; i++)
@@ -600,7 +611,7 @@
buf[5] = htonl(8); /* where to copy to */
buf[6] = htonl(0); /* where to jump to */
- submit = mgp->sram + 0xfc0000;
+ submit = mgp->sram + MXGEFW_BOOT_HANDOFF;
myri10ge_pio_copy(submit, &buf, sizeof(buf));
mb();
@@ -764,6 +775,7 @@
mgp->rx_small.cnt = 0;
mgp->rx_done.idx = 0;
mgp->rx_done.cnt = 0;
+ mgp->link_changes = 0;
status = myri10ge_update_mac_address(mgp, mgp->dev->dev_addr);
myri10ge_change_promisc(mgp, 0, 0);
myri10ge_change_pause(mgp, mgp->pause);
@@ -798,12 +810,13 @@
* pages directly and building a fraglist in the near future.
*/
-static inline struct sk_buff *myri10ge_alloc_big(int bytes)
+static inline struct sk_buff *myri10ge_alloc_big(struct net_device *dev,
+ int bytes)
{
struct sk_buff *skb;
unsigned long data, roundup;
- skb = dev_alloc_skb(bytes + 4096 + MXGEFW_PAD);
+ skb = netdev_alloc_skb(dev, bytes + 4096 + MXGEFW_PAD);
if (skb == NULL)
return NULL;
@@ -821,12 +834,13 @@
/* Allocate 2x as much space as required and use whichever portion
* does not cross a 4KB boundary */
-static inline struct sk_buff *myri10ge_alloc_small_safe(unsigned int bytes)
+static inline struct sk_buff *myri10ge_alloc_small_safe(struct net_device *dev,
+ unsigned int bytes)
{
struct sk_buff *skb;
unsigned long data, boundary;
- skb = dev_alloc_skb(2 * (bytes + MXGEFW_PAD) - 1);
+ skb = netdev_alloc_skb(dev, 2 * (bytes + MXGEFW_PAD) - 1);
if (unlikely(skb == NULL))
return NULL;
@@ -847,12 +861,13 @@
/* Allocate just enough space, and verify that the allocated
* space does not cross a 4KB boundary */
-static inline struct sk_buff *myri10ge_alloc_small(int bytes)
+static inline struct sk_buff *myri10ge_alloc_small(struct net_device *dev,
+ int bytes)
{
struct sk_buff *skb;
unsigned long roundup, data, end;
- skb = dev_alloc_skb(bytes + 16 + MXGEFW_PAD);
+ skb = netdev_alloc_skb(dev, bytes + 16 + MXGEFW_PAD);
if (unlikely(skb == NULL))
return NULL;
@@ -868,15 +883,17 @@
"myri10ge_alloc_small: small skb crossed 4KB boundary\n");
myri10ge_skb_cross_4k = 1;
dev_kfree_skb_any(skb);
- skb = myri10ge_alloc_small_safe(bytes);
+ skb = myri10ge_alloc_small_safe(dev, bytes);
}
return skb;
}
static inline int
-myri10ge_getbuf(struct myri10ge_rx_buf *rx, struct pci_dev *pdev, int bytes,
- int idx)
+myri10ge_getbuf(struct myri10ge_rx_buf *rx, struct myri10ge_priv *mgp,
+ int bytes, int idx)
{
+ struct net_device *dev = mgp->dev;
+ struct pci_dev *pdev = mgp->pdev;
struct sk_buff *skb;
dma_addr_t bus;
int len, retval = 0;
@@ -884,11 +901,11 @@
bytes += VLAN_HLEN; /* account for 802.1q vlan tag */
if ((bytes + MXGEFW_PAD) > (4096 - 16) /* linux overhead */ )
- skb = myri10ge_alloc_big(bytes);
+ skb = myri10ge_alloc_big(dev, bytes);
else if (myri10ge_skb_cross_4k)
- skb = myri10ge_alloc_small_safe(bytes);
+ skb = myri10ge_alloc_small_safe(dev, bytes);
else
- skb = myri10ge_alloc_small(bytes);
+ skb = myri10ge_alloc_small(dev, bytes);
if (unlikely(skb == NULL)) {
rx->alloc_fail++;
@@ -951,7 +968,7 @@
unmap_len = pci_unmap_len(&rx->info[idx], len);
/* try to replace the received skb */
- if (myri10ge_getbuf(rx, mgp->pdev, bytes, idx)) {
+ if (myri10ge_getbuf(rx, mgp, bytes, idx)) {
/* drop the frame -- the old skbuf is re-cycled */
mgp->stats.rx_dropped += 1;
return 0;
@@ -968,7 +985,6 @@
skb_put(skb, len);
skb->protocol = eth_type_trans(skb, mgp->dev);
- skb->dev = mgp->dev;
if (mgp->csum_flag) {
if ((skb->protocol == ntohs(ETH_P_IP)) ||
(skb->protocol == ntohs(ETH_P_IPV6))) {
@@ -1081,13 +1097,19 @@
if (mgp->link_state != stats->link_up) {
mgp->link_state = stats->link_up;
if (mgp->link_state) {
- printk(KERN_INFO "myri10ge: %s: link up\n",
- mgp->dev->name);
+ if (netif_msg_link(mgp))
+ printk(KERN_INFO
+ "myri10ge: %s: link up\n",
+ mgp->dev->name);
netif_carrier_on(mgp->dev);
+ mgp->link_changes++;
} else {
- printk(KERN_INFO "myri10ge: %s: link down\n",
- mgp->dev->name);
+ if (netif_msg_link(mgp))
+ printk(KERN_INFO
+ "myri10ge: %s: link down\n",
+ mgp->dev->name);
netif_carrier_off(mgp->dev);
+ mgp->link_changes++;
}
}
if (mgp->rdma_tags_available !=
@@ -1289,7 +1311,8 @@
"serial_number", "tx_pkt_start", "tx_pkt_done",
"tx_req", "tx_done", "rx_small_cnt", "rx_big_cnt",
"wake_queue", "stop_queue", "watchdog_resets", "tx_linearized",
- "link_up", "dropped_link_overflow", "dropped_link_error_or_filtered",
+ "link_changes", "link_up", "dropped_link_overflow",
+ "dropped_link_error_or_filtered", "dropped_multicast_filtered",
"dropped_runt", "dropped_overrun", "dropped_no_small_buffer",
"dropped_no_big_buffer"
};
@@ -1341,16 +1364,31 @@
data[i++] = (unsigned int)mgp->stop_queue;
data[i++] = (unsigned int)mgp->watchdog_resets;
data[i++] = (unsigned int)mgp->tx_linearized;
+ data[i++] = (unsigned int)mgp->link_changes;
data[i++] = (unsigned int)ntohl(mgp->fw_stats->link_up);
data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_link_overflow);
data[i++] =
(unsigned int)ntohl(mgp->fw_stats->dropped_link_error_or_filtered);
+ data[i++] =
+ (unsigned int)ntohl(mgp->fw_stats->dropped_multicast_filtered);
data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_runt);
data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_overrun);
data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_no_small_buffer);
data[i++] = (unsigned int)ntohl(mgp->fw_stats->dropped_no_big_buffer);
}
+static void myri10ge_set_msglevel(struct net_device *netdev, u32 value)
+{
+ struct myri10ge_priv *mgp = netdev_priv(netdev);
+ mgp->msg_enable = value;
+}
+
+static u32 myri10ge_get_msglevel(struct net_device *netdev)
+{
+ struct myri10ge_priv *mgp = netdev_priv(netdev);
+ return mgp->msg_enable;
+}
+
static struct ethtool_ops myri10ge_ethtool_ops = {
.get_settings = myri10ge_get_settings,
.get_drvinfo = myri10ge_get_drvinfo,
@@ -1371,7 +1409,9 @@
#endif
.get_strings = myri10ge_get_strings,
.get_stats_count = myri10ge_get_stats_count,
- .get_ethtool_stats = myri10ge_get_ethtool_stats
+ .get_ethtool_stats = myri10ge_get_ethtool_stats,
+ .set_msglevel = myri10ge_set_msglevel,
+ .get_msglevel = myri10ge_get_msglevel
};
static int myri10ge_allocate_rings(struct net_device *dev)
@@ -1439,7 +1479,7 @@
/* Fill the receive rings */
for (i = 0; i <= mgp->rx_small.mask; i++) {
- status = myri10ge_getbuf(&mgp->rx_small, mgp->pdev,
+ status = myri10ge_getbuf(&mgp->rx_small, mgp,
mgp->small_bytes, i);
if (status) {
printk(KERN_ERR
@@ -1451,8 +1491,7 @@
for (i = 0; i <= mgp->rx_big.mask; i++) {
status =
- myri10ge_getbuf(&mgp->rx_big, mgp->pdev,
- dev->mtu + ETH_HLEN, i);
+ myri10ge_getbuf(&mgp->rx_big, mgp, dev->mtu + ETH_HLEN, i);
if (status) {
printk(KERN_ERR
"myri10ge: %s: alloced only %d big bufs\n",
@@ -1648,9 +1687,11 @@
}
if (mgp->mtrr >= 0) {
- mgp->tx.wc_fifo = (u8 __iomem *) mgp->sram + 0x200000;
- mgp->rx_small.wc_fifo = (u8 __iomem *) mgp->sram + 0x300000;
- mgp->rx_big.wc_fifo = (u8 __iomem *) mgp->sram + 0x340000;
+ mgp->tx.wc_fifo = (u8 __iomem *) mgp->sram + MXGEFW_ETH_SEND_4;
+ mgp->rx_small.wc_fifo =
+ (u8 __iomem *) mgp->sram + MXGEFW_ETH_RECV_SMALL;
+ mgp->rx_big.wc_fifo =
+ (u8 __iomem *) mgp->sram + MXGEFW_ETH_RECV_BIG;
} else {
mgp->tx.wc_fifo = NULL;
mgp->rx_small.wc_fifo = NULL;
@@ -1686,7 +1727,21 @@
cmd.data0 = MYRI10GE_LOWPART_TO_U32(mgp->fw_stats_bus);
cmd.data1 = MYRI10GE_HIGHPART_TO_U32(mgp->fw_stats_bus);
- status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_STATS_DMA, &cmd, 0);
+ cmd.data2 = sizeof(struct mcp_irq_data);
+ status = myri10ge_send_cmd(mgp, MXGEFW_CMD_SET_STATS_DMA_V2, &cmd, 0);
+ if (status == -ENOSYS) {
+ dma_addr_t bus = mgp->fw_stats_bus;
+ bus += offsetof(struct mcp_irq_data, send_done_count);
+ cmd.data0 = MYRI10GE_LOWPART_TO_U32(bus);
+ cmd.data1 = MYRI10GE_HIGHPART_TO_U32(bus);
+ status = myri10ge_send_cmd(mgp,
+ MXGEFW_CMD_SET_STATS_DMA_OBSOLETE,
+ &cmd, 0);
+ /* Firmware cannot support multicast without STATS_DMA_V2 */
+ mgp->fw_multicast_support = 0;
+ } else {
+ mgp->fw_multicast_support = 1;
+ }
if (status) {
printk(KERN_ERR "myri10ge: %s: Couldn't set stats DMA\n",
dev->name);
@@ -1841,7 +1896,8 @@
if (cnt > 0) {
/* pad it to 64 bytes. The src is 64 bytes bigger than it
* needs to be so that we don't overrun it */
- myri10ge_pio_copy(tx->wc_fifo + (cnt << 18), src, 64);
+ myri10ge_pio_copy(tx->wc_fifo + MXGEFW_ETH_SEND_OFFSET(cnt),
+ src, 64);
mb();
}
}
@@ -2140,9 +2196,81 @@
static void myri10ge_set_multicast_list(struct net_device *dev)
{
+ struct myri10ge_cmd cmd;
+ struct myri10ge_priv *mgp;
+ struct dev_mc_list *mc_list;
+ int err;
+
+ mgp = netdev_priv(dev);
/* can be called from atomic contexts,
* pass 1 to force atomicity in myri10ge_send_cmd() */
- myri10ge_change_promisc(netdev_priv(dev), dev->flags & IFF_PROMISC, 1);
+ myri10ge_change_promisc(mgp, dev->flags & IFF_PROMISC, 1);
+
+ /* This firmware is known to not support multicast */
+ if (!mgp->fw_multicast_support)
+ return;
+
+ /* Disable multicast filtering */
+
+ err = myri10ge_send_cmd(mgp, MXGEFW_ENABLE_ALLMULTI, &cmd, 1);
+ if (err != 0) {
+ printk(KERN_ERR "myri10ge: %s: Failed MXGEFW_ENABLE_ALLMULTI,"
+ " error status: %d\n", dev->name, err);
+ goto abort;
+ }
+
+ if (dev->flags & IFF_ALLMULTI) {
+ /* request to disable multicast filtering, so quit here */
+ return;
+ }
+
+ /* Flush the filters */
+
+ err = myri10ge_send_cmd(mgp, MXGEFW_LEAVE_ALL_MULTICAST_GROUPS,
+ &cmd, 1);
+ if (err != 0) {
+ printk(KERN_ERR
+ "myri10ge: %s: Failed MXGEFW_LEAVE_ALL_MULTICAST_GROUPS"
+ ", error status: %d\n", dev->name, err);
+ goto abort;
+ }
+
+ /* Walk the multicast list, and add each address */
+ for (mc_list = dev->mc_list; mc_list != NULL; mc_list = mc_list->next) {
+ memcpy(&cmd.data0, &mc_list->dmi_addr, 4);
+ memcpy(&cmd.data1, ((char *)&mc_list->dmi_addr) + 4, 2);
+ cmd.data0 = htonl(cmd.data0);
+ cmd.data1 = htonl(cmd.data1);
+ err = myri10ge_send_cmd(mgp, MXGEFW_JOIN_MULTICAST_GROUP,
+ &cmd, 1);
+
+ if (err != 0) {
+ printk(KERN_ERR "myri10ge: %s: Failed "
+ "MXGEFW_JOIN_MULTICAST_GROUP, error status:"
+ "%d\t", dev->name, err);
+ printk(KERN_ERR "MAC %02x:%02x:%02x:%02x:%02x:%02x\n",
+ ((unsigned char *)&mc_list->dmi_addr)[0],
+ ((unsigned char *)&mc_list->dmi_addr)[1],
+ ((unsigned char *)&mc_list->dmi_addr)[2],
+ ((unsigned char *)&mc_list->dmi_addr)[3],
+ ((unsigned char *)&mc_list->dmi_addr)[4],
+ ((unsigned char *)&mc_list->dmi_addr)[5]
+ );
+ goto abort;
+ }
+ }
+ /* Enable multicast filtering */
+ err = myri10ge_send_cmd(mgp, MXGEFW_DISABLE_ALLMULTI, &cmd, 1);
+ if (err != 0) {
+ printk(KERN_ERR "myri10ge: %s: Failed MXGEFW_DISABLE_ALLMULTI,"
+ "error status: %d\n", dev->name, err);
+ goto abort;
+ }
+
+ return;
+
+abort:
+ return;
}
static int myri10ge_set_mac_address(struct net_device *dev, void *addr)
@@ -2581,6 +2709,7 @@
mgp->csum_flag = MXGEFW_FLAGS_CKSUM;
mgp->pause = myri10ge_flow_control;
mgp->intr_coal_delay = myri10ge_intr_coal_delay;
+ mgp->msg_enable = netif_msg_init(myri10ge_debug, MYRI10GE_MSG_DEFAULT);
init_waitqueue_head(&mgp->down_wq);
if (pci_enable_device(pdev)) {
diff --git a/drivers/net/myri10ge/myri10ge_mcp.h b/drivers/net/myri10ge/myri10ge_mcp.h
index 0a6cae6..9519ae7 100644
--- a/drivers/net/myri10ge/myri10ge_mcp.h
+++ b/drivers/net/myri10ge/myri10ge_mcp.h
@@ -91,7 +91,19 @@
/* Commands */
-#define MXGEFW_CMD_OFFSET 0xf80000
+#define MXGEFW_BOOT_HANDOFF 0xfc0000
+#define MXGEFW_BOOT_DUMMY_RDMA 0xfc01c0
+
+#define MXGEFW_ETH_CMD 0xf80000
+#define MXGEFW_ETH_SEND_4 0x200000
+#define MXGEFW_ETH_SEND_1 0x240000
+#define MXGEFW_ETH_SEND_2 0x280000
+#define MXGEFW_ETH_SEND_3 0x2c0000
+#define MXGEFW_ETH_RECV_SMALL 0x300000
+#define MXGEFW_ETH_RECV_BIG 0x340000
+
+#define MXGEFW_ETH_SEND(n) (0x200000 + (((n) & 0x03) * 0x40000))
+#define MXGEFW_ETH_SEND_OFFSET(n) (MXGEFW_ETH_SEND(n) - MXGEFW_ETH_SEND_4)
enum myri10ge_mcp_cmd_type {
MXGEFW_CMD_NONE = 0,
@@ -154,7 +166,7 @@
MXGEFW_CMD_SET_MTU,
MXGEFW_CMD_GET_INTR_COAL_DELAY_OFFSET, /* in microseconds */
MXGEFW_CMD_SET_STATS_INTERVAL, /* in microseconds */
- MXGEFW_CMD_SET_STATS_DMA,
+ MXGEFW_CMD_SET_STATS_DMA_OBSOLETE, /* replaced by SET_STATS_DMA_V2 */
MXGEFW_ENABLE_PROMISC,
MXGEFW_DISABLE_PROMISC,
@@ -168,7 +180,26 @@
* data2 = RDMA length (MSH), WDMA length (LSH)
* command return data = repetitions (MSH), 0.5-ms ticks (LSH)
*/
- MXGEFW_DMA_TEST
+ MXGEFW_DMA_TEST,
+
+ MXGEFW_ENABLE_ALLMULTI,
+ MXGEFW_DISABLE_ALLMULTI,
+
+ /* returns MXGEFW_CMD_ERROR_MULTICAST
+ * if there is no room in the cache
+ * data0,MSH(data1) = multicast group address */
+ MXGEFW_JOIN_MULTICAST_GROUP,
+ /* returns MXGEFW_CMD_ERROR_MULTICAST
+ * if the address is not in the cache,
+ * or is equal to FF-FF-FF-FF-FF-FF
+ * data0,MSH(data1) = multicast group address */
+ MXGEFW_LEAVE_MULTICAST_GROUP,
+ MXGEFW_LEAVE_ALL_MULTICAST_GROUPS,
+
+ MXGEFW_CMD_SET_STATS_DMA_V2,
+ /* data0, data1 = bus addr,
+ * data2 = sizeof(struct mcp_irq_data) from driver point of view, allows
+ * adding new stuff to mcp_irq_data without changing the ABI */
};
enum myri10ge_mcp_cmd_status {
@@ -180,11 +211,17 @@
MXGEFW_CMD_ERROR_CLOSED,
MXGEFW_CMD_ERROR_HASH_ERROR,
MXGEFW_CMD_ERROR_BAD_PORT,
- MXGEFW_CMD_ERROR_RESOURCES
+ MXGEFW_CMD_ERROR_RESOURCES,
+ MXGEFW_CMD_ERROR_MULTICAST
};
-/* 40 Bytes */
+#define MXGEFW_OLD_IRQ_DATA_LEN 40
+
struct mcp_irq_data {
+ /* add new counters at the beginning */
+ u32 future_use[5];
+ u32 dropped_multicast_filtered;
+ /* 40 Bytes */
u32 send_done_count;
u32 link_up;
diff --git a/drivers/net/natsemi.c b/drivers/net/natsemi.c
index db0475a..9510030 100644
--- a/drivers/net/natsemi.c
+++ b/drivers/net/natsemi.c
@@ -3246,7 +3246,7 @@
printk(version);
#endif
- return pci_module_init (&natsemi_driver);
+ return pci_register_driver(&natsemi_driver);
}
static void __exit natsemi_exit_mod (void)
diff --git a/drivers/net/ne2k-pci.c b/drivers/net/ne2k-pci.c
index 34bdba9..654b477 100644
--- a/drivers/net/ne2k-pci.c
+++ b/drivers/net/ne2k-pci.c
@@ -702,7 +702,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init (&ne2k_driver);
+ return pci_register_driver(&ne2k_driver);
}
diff --git a/drivers/net/netx-eth.c b/drivers/net/netx-eth.c
index b1311ae..30ed9a5 100644
--- a/drivers/net/netx-eth.c
+++ b/drivers/net/netx-eth.c
@@ -17,7 +17,6 @@
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
-#include <linux/config.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
diff --git a/drivers/net/ns83820.c b/drivers/net/ns83820.c
index 0e76859..0dedd34 100644
--- a/drivers/net/ns83820.c
+++ b/drivers/net/ns83820.c
@@ -2178,7 +2178,7 @@
static int __init ns83820_init(void)
{
printk(KERN_INFO "ns83820.c: National Semiconductor DP83820 10/100/1000 driver.\n");
- return pci_module_init(&driver);
+ return pci_register_driver(&driver);
}
static void __exit ns83820_exit(void)
diff --git a/drivers/net/pci-skeleton.c b/drivers/net/pci-skeleton.c
index e0e2939..e634762 100644
--- a/drivers/net/pci-skeleton.c
+++ b/drivers/net/pci-skeleton.c
@@ -1963,7 +1963,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init (&netdrv_pci_driver);
+ return pci_register_driver(&netdrv_pci_driver);
}
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index 297e9f8..c54f6a7 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -771,6 +771,7 @@
PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0309),
PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1106),
PCMCIA_DEVICE_MANF_CARD(0x8a01, 0xc1ab),
+ PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202),
PCMCIA_DEVICE_PROD_ID12("AmbiCom,Inc.", "Fast Ethernet PC Card(AMB8110)", 0x49b020a7, 0x119cc9fc),
PCMCIA_DEVICE_PROD_ID124("Fast Ethernet", "16-bit PC Card", "AX88190", 0xb4be14e3, 0x9a12eb6a, 0xab9be5ef),
PCMCIA_DEVICE_PROD_ID12("ASIX", "AX88190", 0x0959823b, 0xab9be5ef),
@@ -786,8 +787,6 @@
PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FastEtherCard", 0x281f1c5d, 0x7ef26116),
PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FEP501", 0x281f1c5d, 0x2e272058),
PCMCIA_DEVICE_PROD_ID14("Network Everywhere", "AX88190", 0x820a67b6, 0xab9be5ef),
- /* this is not specific enough */
- /* PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202), */
PCMCIA_DEVICE_NULL,
};
MODULE_DEVICE_TABLE(pcmcia, axnet_ids);
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 0ecebfc..cc0dcc9 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -654,11 +654,8 @@
SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
if (info->flags & (IS_DL10019|IS_DL10022)) {
- u_char id = inb(dev->base_addr + 0x1a);
dev->do_ioctl = &ei_ioctl;
mii_phy_probe(dev);
- if ((id == 0x30) && !info->pna_phy && (info->eth_phy == 4))
- info->eth_phy = 0;
}
link->dev_node = &info->node;
@@ -821,15 +818,6 @@
}
}
-static void mdio_reset(kio_addr_t addr, int phy_id)
-{
- outb_p(0x08, addr);
- outb_p(0x0c, addr);
- outb_p(0x08, addr);
- outb_p(0x0c, addr);
- outb_p(0x00, addr);
-}
-
/*======================================================================
EEPROM access routines for DL10019 and DL10022 based cards
@@ -942,7 +930,8 @@
}
if (info->flags & IS_DL10022) {
if (info->flags & HAS_MII) {
- mdio_reset(nic_base + DLINK_GPIO, info->eth_phy);
+ /* Advertise 100F, 100H, 10F, 10H */
+ mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 4, 0x01e1);
/* Restart MII autonegotiation */
mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 0, 0x0000);
mdio_write(nic_base + DLINK_GPIO, info->eth_phy, 0, 0x1200);
diff --git a/drivers/net/pcnet32.c b/drivers/net/pcnet32.c
index d50bcb8..5e26fe8 100644
--- a/drivers/net/pcnet32.c
+++ b/drivers/net/pcnet32.c
@@ -2978,7 +2978,7 @@
tx_start = tx_start_pt;
/* find the PCI devices */
- if (!pci_module_init(&pcnet32_driver))
+ if (!pci_register_driver(&pcnet32_driver))
pcnet32_have_pci = 1;
/* should we find any remaining VLbus devices ? */
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c
index 25e31fb..b1d8ed4 100644
--- a/drivers/net/phy/smsc.c
+++ b/drivers/net/phy/smsc.c
@@ -14,7 +14,6 @@
*
*/
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mii.h>
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
index ffd215d..792716b 100644
--- a/drivers/net/phy/vitesse.c
+++ b/drivers/net/phy/vitesse.c
@@ -12,7 +12,6 @@
*
*/
-#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mii.h>
diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c
new file mode 100644
index 0000000..c729aee
--- /dev/null
+++ b/drivers/net/qla3xxx.c
@@ -0,0 +1,3537 @@
+/*
+ * QLogic QLA3xxx NIC HBA Driver
+ * Copyright (c) 2003-2006 QLogic Corporation
+ *
+ * See LICENSE.qla3xxx for copyright and licensing details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/list.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/dmapool.h>
+#include <linux/mempool.h>
+#include <linux/spinlock.h>
+#include <linux/kthread.h>
+#include <linux/interrupt.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/ip.h>
+#include <linux/if_arp.h>
+#include <linux/if_ether.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/skbuff.h>
+#include <linux/rtnetlink.h>
+#include <linux/if_vlan.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+
+#include "qla3xxx.h"
+
+#define DRV_NAME "qla3xxx"
+#define DRV_STRING "QLogic ISP3XXX Network Driver"
+#define DRV_VERSION "v2.02.00-k36"
+#define PFX DRV_NAME " "
+
+static const char ql3xxx_driver_name[] = DRV_NAME;
+static const char ql3xxx_driver_version[] = DRV_VERSION;
+
+MODULE_AUTHOR("QLogic Corporation");
+MODULE_DESCRIPTION("QLogic ISP3XXX Network Driver " DRV_VERSION " ");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static const u32 default_msg
+ = NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK
+ | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN;
+
+static int debug = -1; /* defaults above */
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+static int msi;
+module_param(msi, int, 0);
+MODULE_PARM_DESC(msi, "Turn on Message Signaled Interrupts.");
+
+static struct pci_device_id ql3xxx_pci_tbl[] __devinitdata = {
+ {PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QL3022_DEVICE_ID)},
+ /* required last entry */
+ {0,}
+};
+
+MODULE_DEVICE_TABLE(pci, ql3xxx_pci_tbl);
+
+/*
+ * Caller must take hw_lock.
+ */
+static int ql_sem_spinlock(struct ql3_adapter *qdev,
+ u32 sem_mask, u32 sem_bits)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ u32 value;
+ unsigned int seconds = 3;
+
+ do {
+ writel((sem_mask | sem_bits),
+ &port_regs->CommonRegs.semaphoreReg);
+ value = readl(&port_regs->CommonRegs.semaphoreReg);
+ if ((value & (sem_mask >> 16)) == sem_bits)
+ return 0;
+ ssleep(1);
+ } while(--seconds);
+ return -1;
+}
+
+static void ql_sem_unlock(struct ql3_adapter *qdev, u32 sem_mask)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ writel(sem_mask, &port_regs->CommonRegs.semaphoreReg);
+ readl(&port_regs->CommonRegs.semaphoreReg);
+}
+
+static int ql_sem_lock(struct ql3_adapter *qdev, u32 sem_mask, u32 sem_bits)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ u32 value;
+
+ writel((sem_mask | sem_bits), &port_regs->CommonRegs.semaphoreReg);
+ value = readl(&port_regs->CommonRegs.semaphoreReg);
+ return ((value & (sem_mask >> 16)) == sem_bits);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_wait_for_drvr_lock(struct ql3_adapter *qdev)
+{
+ int i = 0;
+
+ while (1) {
+ if (!ql_sem_lock(qdev,
+ QL_DRVR_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index)
+ * 2) << 1)) {
+ if (i < 10) {
+ ssleep(1);
+ i++;
+ } else {
+ printk(KERN_ERR PFX "%s: Timed out waiting for "
+ "driver lock...\n",
+ qdev->ndev->name);
+ return 0;
+ }
+ } else {
+ printk(KERN_DEBUG PFX
+ "%s: driver lock acquired.\n",
+ qdev->ndev->name);
+ return 1;
+ }
+ }
+}
+
+static void ql_set_register_page(struct ql3_adapter *qdev, u32 page)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+
+ writel(((ISP_CONTROL_NP_MASK << 16) | page),
+ &port_regs->CommonRegs.ispControlStatus);
+ readl(&port_regs->CommonRegs.ispControlStatus);
+ qdev->current_page = page;
+}
+
+static u32 ql_read_common_reg_l(struct ql3_adapter *qdev,
+ u32 __iomem * reg)
+{
+ u32 value;
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ value = readl(reg);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+ return value;
+}
+
+static u32 ql_read_common_reg(struct ql3_adapter *qdev,
+ u32 __iomem * reg)
+{
+ return readl(reg);
+}
+
+static u32 ql_read_page0_reg_l(struct ql3_adapter *qdev, u32 __iomem *reg)
+{
+ u32 value;
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+
+ if (qdev->current_page != 0)
+ ql_set_register_page(qdev,0);
+ value = readl(reg);
+
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return value;
+}
+
+static u32 ql_read_page0_reg(struct ql3_adapter *qdev, u32 __iomem *reg)
+{
+ if (qdev->current_page != 0)
+ ql_set_register_page(qdev,0);
+ return readl(reg);
+}
+
+static void ql_write_common_reg_l(struct ql3_adapter *qdev,
+ u32 * reg, u32 value)
+{
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ writel(value, (u32 *) reg);
+ readl(reg);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return;
+}
+
+static void ql_write_common_reg(struct ql3_adapter *qdev,
+ u32 * reg, u32 value)
+{
+ writel(value, (u32 *) reg);
+ readl(reg);
+ return;
+}
+
+static void ql_write_page0_reg(struct ql3_adapter *qdev,
+ u32 * reg, u32 value)
+{
+ if (qdev->current_page != 0)
+ ql_set_register_page(qdev,0);
+ writel(value, (u32 *) reg);
+ readl(reg);
+ return;
+}
+
+/*
+ * Caller holds hw_lock. Only called during init.
+ */
+static void ql_write_page1_reg(struct ql3_adapter *qdev,
+ u32 * reg, u32 value)
+{
+ if (qdev->current_page != 1)
+ ql_set_register_page(qdev,1);
+ writel(value, (u32 *) reg);
+ readl(reg);
+ return;
+}
+
+/*
+ * Caller holds hw_lock. Only called during init.
+ */
+static void ql_write_page2_reg(struct ql3_adapter *qdev,
+ u32 * reg, u32 value)
+{
+ if (qdev->current_page != 2)
+ ql_set_register_page(qdev,2);
+ writel(value, (u32 *) reg);
+ readl(reg);
+ return;
+}
+
+static void ql_disable_interrupts(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+
+ ql_write_common_reg_l(qdev, &port_regs->CommonRegs.ispInterruptMaskReg,
+ (ISP_IMR_ENABLE_INT << 16));
+
+}
+
+static void ql_enable_interrupts(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+
+ ql_write_common_reg_l(qdev, &port_regs->CommonRegs.ispInterruptMaskReg,
+ ((0xff << 16) | ISP_IMR_ENABLE_INT));
+
+}
+
+static void ql_release_to_lrg_buf_free_list(struct ql3_adapter *qdev,
+ struct ql_rcv_buf_cb *lrg_buf_cb)
+{
+ u64 map;
+ lrg_buf_cb->next = NULL;
+
+ if (qdev->lrg_buf_free_tail == NULL) { /* The list is empty */
+ qdev->lrg_buf_free_head = qdev->lrg_buf_free_tail = lrg_buf_cb;
+ } else {
+ qdev->lrg_buf_free_tail->next = lrg_buf_cb;
+ qdev->lrg_buf_free_tail = lrg_buf_cb;
+ }
+
+ if (!lrg_buf_cb->skb) {
+ lrg_buf_cb->skb = dev_alloc_skb(qdev->lrg_buffer_len);
+ if (unlikely(!lrg_buf_cb->skb)) {
+ printk(KERN_ERR PFX "%s: failed dev_alloc_skb().\n",
+ qdev->ndev->name);
+ qdev->lrg_buf_skb_check++;
+ } else {
+ /*
+ * We save some space to copy the ethhdr from first
+ * buffer
+ */
+ skb_reserve(lrg_buf_cb->skb, QL_HEADER_SPACE);
+ map = pci_map_single(qdev->pdev,
+ lrg_buf_cb->skb->data,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE,
+ PCI_DMA_FROMDEVICE);
+ lrg_buf_cb->buf_phy_addr_low =
+ cpu_to_le32(LS_64BITS(map));
+ lrg_buf_cb->buf_phy_addr_high =
+ cpu_to_le32(MS_64BITS(map));
+ pci_unmap_addr_set(lrg_buf_cb, mapaddr, map);
+ pci_unmap_len_set(lrg_buf_cb, maplen,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE);
+ }
+ }
+
+ qdev->lrg_buf_free_count++;
+}
+
+static struct ql_rcv_buf_cb *ql_get_from_lrg_buf_free_list(struct ql3_adapter
+ *qdev)
+{
+ struct ql_rcv_buf_cb *lrg_buf_cb;
+
+ if ((lrg_buf_cb = qdev->lrg_buf_free_head) != NULL) {
+ if ((qdev->lrg_buf_free_head = lrg_buf_cb->next) == NULL)
+ qdev->lrg_buf_free_tail = NULL;
+ qdev->lrg_buf_free_count--;
+ }
+
+ return lrg_buf_cb;
+}
+
+static u32 addrBits = EEPROM_NO_ADDR_BITS;
+static u32 dataBits = EEPROM_NO_DATA_BITS;
+
+static void fm93c56a_deselect(struct ql3_adapter *qdev);
+static void eeprom_readword(struct ql3_adapter *qdev, u32 eepromAddr,
+ unsigned short *value);
+
+/*
+ * Caller holds hw_lock.
+ */
+static void fm93c56a_select(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ qdev->eeprom_cmd_data = AUBURN_EEPROM_CS_1;
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->eeprom_cmd_data);
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void fm93c56a_cmd(struct ql3_adapter *qdev, u32 cmd, u32 eepromAddr)
+{
+ int i;
+ u32 mask;
+ u32 dataBit;
+ u32 previousBit;
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ /* Clock in a zero, then do the start bit */
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->eeprom_cmd_data |
+ AUBURN_EEPROM_DO_1);
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | AUBURN_EEPROM_DO_1 |
+ AUBURN_EEPROM_CLK_RISE);
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | AUBURN_EEPROM_DO_1 |
+ AUBURN_EEPROM_CLK_FALL);
+
+ mask = 1 << (FM93C56A_CMD_BITS - 1);
+ /* Force the previous data bit to be different */
+ previousBit = 0xffff;
+ for (i = 0; i < FM93C56A_CMD_BITS; i++) {
+ dataBit =
+ (cmd & mask) ? AUBURN_EEPROM_DO_1 : AUBURN_EEPROM_DO_0;
+ if (previousBit != dataBit) {
+ /*
+ * If the bit changed, then change the DO state to
+ * match
+ */
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit);
+ previousBit = dataBit;
+ }
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit |
+ AUBURN_EEPROM_CLK_RISE);
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit |
+ AUBURN_EEPROM_CLK_FALL);
+ cmd = cmd << 1;
+ }
+
+ mask = 1 << (addrBits - 1);
+ /* Force the previous data bit to be different */
+ previousBit = 0xffff;
+ for (i = 0; i < addrBits; i++) {
+ dataBit =
+ (eepromAddr & mask) ? AUBURN_EEPROM_DO_1 :
+ AUBURN_EEPROM_DO_0;
+ if (previousBit != dataBit) {
+ /*
+ * If the bit changed, then change the DO state to
+ * match
+ */
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit);
+ previousBit = dataBit;
+ }
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit |
+ AUBURN_EEPROM_CLK_RISE);
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->
+ eeprom_cmd_data | dataBit |
+ AUBURN_EEPROM_CLK_FALL);
+ eepromAddr = eepromAddr << 1;
+ }
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void fm93c56a_deselect(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ qdev->eeprom_cmd_data = AUBURN_EEPROM_CS_0;
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->eeprom_cmd_data);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void fm93c56a_datain(struct ql3_adapter *qdev, unsigned short *value)
+{
+ int i;
+ u32 data = 0;
+ u32 dataBit;
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ /* Read the data bits */
+ /* The first bit is a dummy. Clock right over it. */
+ for (i = 0; i < dataBits; i++) {
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->eeprom_cmd_data |
+ AUBURN_EEPROM_CLK_RISE);
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg,
+ ISP_NVRAM_MASK | qdev->eeprom_cmd_data |
+ AUBURN_EEPROM_CLK_FALL);
+ dataBit =
+ (ql_read_common_reg
+ (qdev,
+ &port_regs->CommonRegs.
+ serialPortInterfaceReg) & AUBURN_EEPROM_DI_1) ? 1 : 0;
+ data = (data << 1) | dataBit;
+ }
+ *value = (u16) data;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void eeprom_readword(struct ql3_adapter *qdev,
+ u32 eepromAddr, unsigned short *value)
+{
+ fm93c56a_select(qdev);
+ fm93c56a_cmd(qdev, (int)FM93C56A_READ, eepromAddr);
+ fm93c56a_datain(qdev, value);
+ fm93c56a_deselect(qdev);
+}
+
+static void ql_swap_mac_addr(u8 * macAddress)
+{
+#ifdef __BIG_ENDIAN
+ u8 temp;
+ temp = macAddress[0];
+ macAddress[0] = macAddress[1];
+ macAddress[1] = temp;
+ temp = macAddress[2];
+ macAddress[2] = macAddress[3];
+ macAddress[3] = temp;
+ temp = macAddress[4];
+ macAddress[4] = macAddress[5];
+ macAddress[5] = temp;
+#endif
+}
+
+static int ql_get_nvram_params(struct ql3_adapter *qdev)
+{
+ u16 *pEEPROMData;
+ u16 checksum = 0;
+ u32 index;
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+
+ pEEPROMData = (u16 *) & qdev->nvram_data;
+ qdev->eeprom_cmd_data = 0;
+ if(ql_sem_spinlock(qdev, QL_NVRAM_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 10)) {
+ printk(KERN_ERR PFX"%s: Failed ql_sem_spinlock().\n",
+ __func__);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return -1;
+ }
+
+ for (index = 0; index < EEPROM_SIZE; index++) {
+ eeprom_readword(qdev, index, pEEPROMData);
+ checksum += *pEEPROMData;
+ pEEPROMData++;
+ }
+ ql_sem_unlock(qdev, QL_NVRAM_SEM_MASK);
+
+ if (checksum != 0) {
+ printk(KERN_ERR PFX "%s: checksum should be zero, is %x!!\n",
+ qdev->ndev->name, checksum);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return -1;
+ }
+
+ /*
+ * We have a problem with endianness for the MAC addresses
+ * and the two 8-bit values version, and numPorts. We
+ * have to swap them on big endian systems.
+ */
+ ql_swap_mac_addr(qdev->nvram_data.funcCfg_fn0.macAddress);
+ ql_swap_mac_addr(qdev->nvram_data.funcCfg_fn1.macAddress);
+ ql_swap_mac_addr(qdev->nvram_data.funcCfg_fn2.macAddress);
+ ql_swap_mac_addr(qdev->nvram_data.funcCfg_fn3.macAddress);
+ pEEPROMData = (u16 *) & qdev->nvram_data.version;
+ *pEEPROMData = le16_to_cpu(*pEEPROMData);
+
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return checksum;
+}
+
+static const u32 PHYAddr[2] = {
+ PORT0_PHY_ADDRESS, PORT1_PHY_ADDRESS
+};
+
+static int ql_wait_for_mii_ready(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 temp;
+ int count = 1000;
+
+ while (count) {
+ temp = ql_read_page0_reg(qdev, &port_regs->macMIIStatusReg);
+ if (!(temp & MAC_MII_STATUS_BSY))
+ return 0;
+ udelay(10);
+ count--;
+ }
+ return -1;
+}
+
+static void ql_mii_enable_scan_mode(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 scanControl;
+
+ if (qdev->numPorts > 1) {
+ /* Auto scan will cycle through multiple ports */
+ scanControl = MAC_MII_CONTROL_AS | MAC_MII_CONTROL_SC;
+ } else {
+ scanControl = MAC_MII_CONTROL_SC;
+ }
+
+ /*
+ * Scan register 1 of PHY/PETBI,
+ * Set up to scan both devices
+ * The autoscan starts from the first register, completes
+ * the last one before rolling over to the first
+ */
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ PHYAddr[0] | MII_SCAN_REGISTER);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ (scanControl) |
+ ((MAC_MII_CONTROL_SC | MAC_MII_CONTROL_AS) << 16));
+}
+
+static u8 ql_mii_disable_scan_mode(struct ql3_adapter *qdev)
+{
+ u8 ret;
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ /* See if scan mode is enabled before we turn it off */
+ if (ql_read_page0_reg(qdev, &port_regs->macMIIMgmtControlReg) &
+ (MAC_MII_CONTROL_AS | MAC_MII_CONTROL_SC)) {
+ /* Scan is enabled */
+ ret = 1;
+ } else {
+ /* Scan is disabled */
+ ret = 0;
+ }
+
+ /*
+ * When disabling scan mode you must first change the MII register
+ * address
+ */
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ PHYAddr[0] | MII_SCAN_REGISTER);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ ((MAC_MII_CONTROL_SC | MAC_MII_CONTROL_AS |
+ MAC_MII_CONTROL_RC) << 16));
+
+ return ret;
+}
+
+static int ql_mii_write_reg_ex(struct ql3_adapter *qdev,
+ u16 regAddr, u16 value, u32 mac_index)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u8 scanWasEnabled;
+
+ scanWasEnabled = ql_mii_disable_scan_mode(qdev);
+
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ PHYAddr[mac_index] | regAddr);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtDataReg, value);
+
+ /* Wait for write to complete 9/10/04 SJP */
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to"
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ if (scanWasEnabled)
+ ql_mii_enable_scan_mode(qdev);
+
+ return 0;
+}
+
+static int ql_mii_read_reg_ex(struct ql3_adapter *qdev, u16 regAddr,
+ u16 * value, u32 mac_index)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u8 scanWasEnabled;
+ u32 temp;
+
+ scanWasEnabled = ql_mii_disable_scan_mode(qdev);
+
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ PHYAddr[mac_index] | regAddr);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ (MAC_MII_CONTROL_RC << 16));
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ (MAC_MII_CONTROL_RC << 16) | MAC_MII_CONTROL_RC);
+
+ /* Wait for the read to complete */
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free after issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ temp = ql_read_page0_reg(qdev, &port_regs->macMIIMgmtDataReg);
+ *value = (u16) temp;
+
+ if (scanWasEnabled)
+ ql_mii_enable_scan_mode(qdev);
+
+ return 0;
+}
+
+static int ql_mii_write_reg(struct ql3_adapter *qdev, u16 regAddr, u16 value)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ ql_mii_disable_scan_mode(qdev);
+
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ qdev->PHYAddr | regAddr);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtDataReg, value);
+
+ /* Wait for write to complete. */
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ ql_mii_enable_scan_mode(qdev);
+
+ return 0;
+}
+
+static int ql_mii_read_reg(struct ql3_adapter *qdev, u16 regAddr, u16 *value)
+{
+ u32 temp;
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ ql_mii_disable_scan_mode(qdev);
+
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtAddrReg,
+ qdev->PHYAddr | regAddr);
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ (MAC_MII_CONTROL_RC << 16));
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ (MAC_MII_CONTROL_RC << 16) | MAC_MII_CONTROL_RC);
+
+ /* Wait for the read to complete */
+ if (ql_wait_for_mii_ready(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Timed out waiting for management port to "
+ "get free before issuing command.\n",
+ qdev->ndev->name);
+ return -1;
+ }
+
+ temp = ql_read_page0_reg(qdev, &port_regs->macMIIMgmtDataReg);
+ *value = (u16) temp;
+
+ ql_mii_enable_scan_mode(qdev);
+
+ return 0;
+}
+
+static void ql_petbi_reset(struct ql3_adapter *qdev)
+{
+ ql_mii_write_reg(qdev, PETBI_CONTROL_REG, PETBI_CTRL_SOFT_RESET);
+}
+
+static void ql_petbi_start_neg(struct ql3_adapter *qdev)
+{
+ u16 reg;
+
+ /* Enable Auto-negotiation sense */
+ ql_mii_read_reg(qdev, PETBI_TBI_CTRL, ®);
+ reg |= PETBI_TBI_AUTO_SENSE;
+ ql_mii_write_reg(qdev, PETBI_TBI_CTRL, reg);
+
+ ql_mii_write_reg(qdev, PETBI_NEG_ADVER,
+ PETBI_NEG_PAUSE | PETBI_NEG_DUPLEX);
+
+ ql_mii_write_reg(qdev, PETBI_CONTROL_REG,
+ PETBI_CTRL_AUTO_NEG | PETBI_CTRL_RESTART_NEG |
+ PETBI_CTRL_FULL_DUPLEX | PETBI_CTRL_SPEED_1000);
+
+}
+
+static void ql_petbi_reset_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ ql_mii_write_reg_ex(qdev, PETBI_CONTROL_REG, PETBI_CTRL_SOFT_RESET,
+ mac_index);
+}
+
+static void ql_petbi_start_neg_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ u16 reg;
+
+ /* Enable Auto-negotiation sense */
+ ql_mii_read_reg_ex(qdev, PETBI_TBI_CTRL, ®, mac_index);
+ reg |= PETBI_TBI_AUTO_SENSE;
+ ql_mii_write_reg_ex(qdev, PETBI_TBI_CTRL, reg, mac_index);
+
+ ql_mii_write_reg_ex(qdev, PETBI_NEG_ADVER,
+ PETBI_NEG_PAUSE | PETBI_NEG_DUPLEX, mac_index);
+
+ ql_mii_write_reg_ex(qdev, PETBI_CONTROL_REG,
+ PETBI_CTRL_AUTO_NEG | PETBI_CTRL_RESTART_NEG |
+ PETBI_CTRL_FULL_DUPLEX | PETBI_CTRL_SPEED_1000,
+ mac_index);
+}
+
+static void ql_petbi_init(struct ql3_adapter *qdev)
+{
+ ql_petbi_reset(qdev);
+ ql_petbi_start_neg(qdev);
+}
+
+static void ql_petbi_init_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ ql_petbi_reset_ex(qdev, mac_index);
+ ql_petbi_start_neg_ex(qdev, mac_index);
+}
+
+static int ql_is_petbi_neg_pause(struct ql3_adapter *qdev)
+{
+ u16 reg;
+
+ if (ql_mii_read_reg(qdev, PETBI_NEG_PARTNER, ®) < 0)
+ return 0;
+
+ return (reg & PETBI_NEG_PAUSE_MASK) == PETBI_NEG_PAUSE;
+}
+
+static int ql_phy_get_speed(struct ql3_adapter *qdev)
+{
+ u16 reg;
+
+ if (ql_mii_read_reg(qdev, AUX_CONTROL_STATUS, ®) < 0)
+ return 0;
+
+ reg = (((reg & 0x18) >> 3) & 3);
+
+ if (reg == 2)
+ return SPEED_1000;
+ else if (reg == 1)
+ return SPEED_100;
+ else if (reg == 0)
+ return SPEED_10;
+ else
+ return -1;
+}
+
+static int ql_is_full_dup(struct ql3_adapter *qdev)
+{
+ u16 reg;
+
+ if (ql_mii_read_reg(qdev, AUX_CONTROL_STATUS, ®) < 0)
+ return 0;
+
+ return (reg & PHY_AUX_DUPLEX_STAT) != 0;
+}
+
+static int ql_is_phy_neg_pause(struct ql3_adapter *qdev)
+{
+ u16 reg;
+
+ if (ql_mii_read_reg(qdev, PHY_NEG_PARTNER, ®) < 0)
+ return 0;
+
+ return (reg & PHY_NEG_PAUSE) != 0;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_mac_enable(struct ql3_adapter *qdev, u32 enable)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 value;
+
+ if (enable)
+ value = (MAC_CONFIG_REG_PE | (MAC_CONFIG_REG_PE << 16));
+ else
+ value = (MAC_CONFIG_REG_PE << 16);
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev, &port_regs->mac1ConfigReg, value);
+ else
+ ql_write_page0_reg(qdev, &port_regs->mac0ConfigReg, value);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_mac_cfg_soft_reset(struct ql3_adapter *qdev, u32 enable)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 value;
+
+ if (enable)
+ value = (MAC_CONFIG_REG_SR | (MAC_CONFIG_REG_SR << 16));
+ else
+ value = (MAC_CONFIG_REG_SR << 16);
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev, &port_regs->mac1ConfigReg, value);
+ else
+ ql_write_page0_reg(qdev, &port_regs->mac0ConfigReg, value);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_mac_cfg_gig(struct ql3_adapter *qdev, u32 enable)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 value;
+
+ if (enable)
+ value = (MAC_CONFIG_REG_GM | (MAC_CONFIG_REG_GM << 16));
+ else
+ value = (MAC_CONFIG_REG_GM << 16);
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev, &port_regs->mac1ConfigReg, value);
+ else
+ ql_write_page0_reg(qdev, &port_regs->mac0ConfigReg, value);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_mac_cfg_full_dup(struct ql3_adapter *qdev, u32 enable)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 value;
+
+ if (enable)
+ value = (MAC_CONFIG_REG_FD | (MAC_CONFIG_REG_FD << 16));
+ else
+ value = (MAC_CONFIG_REG_FD << 16);
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev, &port_regs->mac1ConfigReg, value);
+ else
+ ql_write_page0_reg(qdev, &port_regs->mac0ConfigReg, value);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_mac_cfg_pause(struct ql3_adapter *qdev, u32 enable)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 value;
+
+ if (enable)
+ value =
+ ((MAC_CONFIG_REG_TF | MAC_CONFIG_REG_RF) |
+ ((MAC_CONFIG_REG_TF | MAC_CONFIG_REG_RF) << 16));
+ else
+ value = ((MAC_CONFIG_REG_TF | MAC_CONFIG_REG_RF) << 16);
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev, &port_regs->mac1ConfigReg, value);
+ else
+ ql_write_page0_reg(qdev, &port_regs->mac0ConfigReg, value);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_is_fiber(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp;
+
+ switch (qdev->mac_index) {
+ case 0:
+ bitToCheck = PORT_STATUS_SM0;
+ break;
+ case 1:
+ bitToCheck = PORT_STATUS_SM1;
+ break;
+ }
+
+ temp = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ return (temp & bitToCheck) != 0;
+}
+
+static int ql_is_auto_cfg(struct ql3_adapter *qdev)
+{
+ u16 reg;
+ ql_mii_read_reg(qdev, 0x00, ®);
+ return (reg & 0x1000) != 0;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_is_auto_neg_complete(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp;
+
+ switch (qdev->mac_index) {
+ case 0:
+ bitToCheck = PORT_STATUS_AC0;
+ break;
+ case 1:
+ bitToCheck = PORT_STATUS_AC1;
+ break;
+ }
+
+ temp = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ if (temp & bitToCheck) {
+ if (netif_msg_link(qdev))
+ printk(KERN_INFO PFX
+ "%s: Auto-Negotiate complete.\n",
+ qdev->ndev->name);
+ return 1;
+ } else {
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Auto-Negotiate incomplete.\n",
+ qdev->ndev->name);
+ return 0;
+ }
+}
+
+/*
+ * ql_is_neg_pause() returns 1 if pause was negotiated to be on
+ */
+static int ql_is_neg_pause(struct ql3_adapter *qdev)
+{
+ if (ql_is_fiber(qdev))
+ return ql_is_petbi_neg_pause(qdev);
+ else
+ return ql_is_phy_neg_pause(qdev);
+}
+
+static int ql_auto_neg_error(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp;
+
+ switch (qdev->mac_index) {
+ case 0:
+ bitToCheck = PORT_STATUS_AE0;
+ break;
+ case 1:
+ bitToCheck = PORT_STATUS_AE1;
+ break;
+ }
+ temp = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ return (temp & bitToCheck) != 0;
+}
+
+static u32 ql_get_link_speed(struct ql3_adapter *qdev)
+{
+ if (ql_is_fiber(qdev))
+ return SPEED_1000;
+ else
+ return ql_phy_get_speed(qdev);
+}
+
+static int ql_is_link_full_dup(struct ql3_adapter *qdev)
+{
+ if (ql_is_fiber(qdev))
+ return 1;
+ else
+ return ql_is_full_dup(qdev);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_link_down_detect(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp;
+
+ switch (qdev->mac_index) {
+ case 0:
+ bitToCheck = ISP_CONTROL_LINK_DN_0;
+ break;
+ case 1:
+ bitToCheck = ISP_CONTROL_LINK_DN_1;
+ break;
+ }
+
+ temp =
+ ql_read_common_reg(qdev, &port_regs->CommonRegs.ispControlStatus);
+ return (temp & bitToCheck) != 0;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_link_down_detect_clear(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ switch (qdev->mac_index) {
+ case 0:
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.ispControlStatus,
+ (ISP_CONTROL_LINK_DN_0) |
+ (ISP_CONTROL_LINK_DN_0 << 16));
+ break;
+
+ case 1:
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.ispControlStatus,
+ (ISP_CONTROL_LINK_DN_1) |
+ (ISP_CONTROL_LINK_DN_1 << 16));
+ break;
+
+ default:
+ return 1;
+ }
+
+ return 0;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_this_adapter_controls_port(struct ql3_adapter *qdev,
+ u32 mac_index)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp;
+
+ switch (mac_index) {
+ case 0:
+ bitToCheck = PORT_STATUS_F1_ENABLED;
+ break;
+ case 1:
+ bitToCheck = PORT_STATUS_F3_ENABLED;
+ break;
+ default:
+ break;
+ }
+
+ temp = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ if (temp & bitToCheck) {
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: is not link master.\n", qdev->ndev->name);
+ return 0;
+ } else {
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: is link master.\n", qdev->ndev->name);
+ return 1;
+ }
+}
+
+static void ql_phy_reset_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ ql_mii_write_reg_ex(qdev, CONTROL_REG, PHY_CTRL_SOFT_RESET, mac_index);
+}
+
+static void ql_phy_start_neg_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ u16 reg;
+
+ ql_mii_write_reg_ex(qdev, PHY_NEG_ADVER,
+ PHY_NEG_PAUSE | PHY_NEG_ADV_SPEED | 1, mac_index);
+
+ ql_mii_read_reg_ex(qdev, CONTROL_REG, ®, mac_index);
+ ql_mii_write_reg_ex(qdev, CONTROL_REG, reg | PHY_CTRL_RESTART_NEG,
+ mac_index);
+}
+
+static void ql_phy_init_ex(struct ql3_adapter *qdev, u32 mac_index)
+{
+ ql_phy_reset_ex(qdev, mac_index);
+ ql_phy_start_neg_ex(qdev, mac_index);
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static u32 ql_get_link_state(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ u32 bitToCheck = 0;
+ u32 temp, linkState;
+
+ switch (qdev->mac_index) {
+ case 0:
+ bitToCheck = PORT_STATUS_UP0;
+ break;
+ case 1:
+ bitToCheck = PORT_STATUS_UP1;
+ break;
+ }
+ temp = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ if (temp & bitToCheck) {
+ linkState = LS_UP;
+ } else {
+ linkState = LS_DOWN;
+ if (netif_msg_link(qdev))
+ printk(KERN_WARNING PFX
+ "%s: Link is down.\n", qdev->ndev->name);
+ }
+ return linkState;
+}
+
+static int ql_port_start(struct ql3_adapter *qdev)
+{
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return -1;
+
+ if (ql_is_fiber(qdev)) {
+ ql_petbi_init(qdev);
+ } else {
+ /* Copper port */
+ ql_phy_init_ex(qdev, qdev->mac_index);
+ }
+
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ return 0;
+}
+
+static int ql_finish_auto_neg(struct ql3_adapter *qdev)
+{
+
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return -1;
+
+ if (!ql_auto_neg_error(qdev)) {
+ if (test_bit(QL_LINK_MASTER,&qdev->flags)) {
+ /* configure the MAC */
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: Configuring link.\n",
+ qdev->ndev->
+ name);
+ ql_mac_cfg_soft_reset(qdev, 1);
+ ql_mac_cfg_gig(qdev,
+ (ql_get_link_speed
+ (qdev) ==
+ SPEED_1000));
+ ql_mac_cfg_full_dup(qdev,
+ ql_is_link_full_dup
+ (qdev));
+ ql_mac_cfg_pause(qdev,
+ ql_is_neg_pause
+ (qdev));
+ ql_mac_cfg_soft_reset(qdev, 0);
+
+ /* enable the MAC */
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: Enabling mac.\n",
+ qdev->ndev->
+ name);
+ ql_mac_enable(qdev, 1);
+ }
+
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: Change port_link_state LS_DOWN to LS_UP.\n",
+ qdev->ndev->name);
+ qdev->port_link_state = LS_UP;
+ netif_start_queue(qdev->ndev);
+ netif_carrier_on(qdev->ndev);
+ if (netif_msg_link(qdev))
+ printk(KERN_INFO PFX
+ "%s: Link is up at %d Mbps, %s duplex.\n",
+ qdev->ndev->name,
+ ql_get_link_speed(qdev),
+ ql_is_link_full_dup(qdev)
+ ? "full" : "half");
+
+ } else { /* Remote error detected */
+
+ if (test_bit(QL_LINK_MASTER,&qdev->flags)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: Remote error detected. "
+ "Calling ql_port_start().\n",
+ qdev->ndev->
+ name);
+ /*
+ * ql_port_start() is shared code and needs
+ * to lock the PHY on it's own.
+ */
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ if(ql_port_start(qdev)) {/* Restart port */
+ return -1;
+ } else
+ return 0;
+ }
+ }
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ return 0;
+}
+
+static void ql_link_state_machine(struct ql3_adapter *qdev)
+{
+ u32 curr_link_state;
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+
+ curr_link_state = ql_get_link_state(qdev);
+
+ if (test_bit(QL_RESET_ACTIVE,&qdev->flags)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_INFO PFX
+ "%s: Reset in progress, skip processing link "
+ "state.\n", qdev->ndev->name);
+ return;
+ }
+
+ switch (qdev->port_link_state) {
+ default:
+ if (test_bit(QL_LINK_MASTER,&qdev->flags)) {
+ ql_port_start(qdev);
+ }
+ qdev->port_link_state = LS_DOWN;
+ /* Fall Through */
+
+ case LS_DOWN:
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: port_link_state = LS_DOWN.\n",
+ qdev->ndev->name);
+ if (curr_link_state == LS_UP) {
+ if (netif_msg_link(qdev))
+ printk(KERN_DEBUG PFX
+ "%s: curr_link_state = LS_UP.\n",
+ qdev->ndev->name);
+ if (ql_is_auto_neg_complete(qdev))
+ ql_finish_auto_neg(qdev);
+
+ if (qdev->port_link_state == LS_UP)
+ ql_link_down_detect_clear(qdev);
+
+ }
+ break;
+
+ case LS_UP:
+ /*
+ * See if the link is currently down or went down and came
+ * back up
+ */
+ if ((curr_link_state == LS_DOWN) || ql_link_down_detect(qdev)) {
+ if (netif_msg_link(qdev))
+ printk(KERN_INFO PFX "%s: Link is down.\n",
+ qdev->ndev->name);
+ qdev->port_link_state = LS_DOWN;
+ }
+ break;
+ }
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+}
+
+/*
+ * Caller must take hw_lock and QL_PHY_GIO_SEM.
+ */
+static void ql_get_phy_owner(struct ql3_adapter *qdev)
+{
+ if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
+ set_bit(QL_LINK_MASTER,&qdev->flags);
+ else
+ clear_bit(QL_LINK_MASTER,&qdev->flags);
+}
+
+/*
+ * Caller must take hw_lock and QL_PHY_GIO_SEM.
+ */
+static void ql_init_scan_mode(struct ql3_adapter *qdev)
+{
+ ql_mii_enable_scan_mode(qdev);
+
+ if (test_bit(QL_LINK_OPTICAL,&qdev->flags)) {
+ if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
+ ql_petbi_init_ex(qdev, qdev->mac_index);
+ } else {
+ if (ql_this_adapter_controls_port(qdev, qdev->mac_index))
+ ql_phy_init_ex(qdev, qdev->mac_index);
+ }
+}
+
+/*
+ * MII_Setup needs to be called before taking the PHY out of reset so that the
+ * management interface clock speed can be set properly. It would be better if
+ * we had a way to disable MDC until after the PHY is out of reset, but we
+ * don't have that capability.
+ */
+static int ql_mii_setup(struct ql3_adapter *qdev)
+{
+ u32 reg;
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return -1;
+
+ /* Divide 125MHz clock by 28 to meet PHY timing requirements */
+ reg = MAC_MII_CONTROL_CLK_SEL_DIV28;
+
+ ql_write_page0_reg(qdev, &port_regs->macMIIMgmtControlReg,
+ reg | ((MAC_MII_CONTROL_CLK_SEL_MASK) << 16));
+
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ return 0;
+}
+
+static u32 ql_supported_modes(struct ql3_adapter *qdev)
+{
+ u32 supported;
+
+ if (test_bit(QL_LINK_OPTICAL,&qdev->flags)) {
+ supported = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
+ | SUPPORTED_Autoneg;
+ } else {
+ supported = SUPPORTED_10baseT_Half
+ | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half
+ | SUPPORTED_100baseT_Full
+ | SUPPORTED_1000baseT_Half
+ | SUPPORTED_1000baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP;
+ }
+
+ return supported;
+}
+
+static int ql_get_auto_cfg_status(struct ql3_adapter *qdev)
+{
+ int status;
+ unsigned long hw_flags;
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return 0;
+ status = ql_is_auto_cfg(qdev);
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return status;
+}
+
+static u32 ql_get_speed(struct ql3_adapter *qdev)
+{
+ u32 status;
+ unsigned long hw_flags;
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return 0;
+ status = ql_get_link_speed(qdev);
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return status;
+}
+
+static int ql_get_full_dup(struct ql3_adapter *qdev)
+{
+ int status;
+ unsigned long hw_flags;
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7))
+ return 0;
+ status = ql_is_link_full_dup(qdev);
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ return status;
+}
+
+
+static int ql_get_settings(struct net_device *ndev, struct ethtool_cmd *ecmd)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+
+ ecmd->transceiver = XCVR_INTERNAL;
+ ecmd->supported = ql_supported_modes(qdev);
+
+ if (test_bit(QL_LINK_OPTICAL,&qdev->flags)) {
+ ecmd->port = PORT_FIBRE;
+ } else {
+ ecmd->port = PORT_TP;
+ ecmd->phy_address = qdev->PHYAddr;
+ }
+ ecmd->advertising = ql_supported_modes(qdev);
+ ecmd->autoneg = ql_get_auto_cfg_status(qdev);
+ ecmd->speed = ql_get_speed(qdev);
+ ecmd->duplex = ql_get_full_dup(qdev);
+ return 0;
+}
+
+static void ql_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *drvinfo)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ strncpy(drvinfo->driver, ql3xxx_driver_name, 32);
+ strncpy(drvinfo->version, ql3xxx_driver_version, 32);
+ strncpy(drvinfo->fw_version, "N/A", 32);
+ strncpy(drvinfo->bus_info, pci_name(qdev->pdev), 32);
+ drvinfo->n_stats = 0;
+ drvinfo->testinfo_len = 0;
+ drvinfo->regdump_len = 0;
+ drvinfo->eedump_len = 0;
+}
+
+static u32 ql_get_msglevel(struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ return qdev->msg_enable;
+}
+
+static void ql_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ qdev->msg_enable = value;
+}
+
+static struct ethtool_ops ql3xxx_ethtool_ops = {
+ .get_settings = ql_get_settings,
+ .get_drvinfo = ql_get_drvinfo,
+ .get_perm_addr = ethtool_op_get_perm_addr,
+ .get_link = ethtool_op_get_link,
+ .get_msglevel = ql_get_msglevel,
+ .set_msglevel = ql_set_msglevel,
+};
+
+static int ql_populate_free_queue(struct ql3_adapter *qdev)
+{
+ struct ql_rcv_buf_cb *lrg_buf_cb = qdev->lrg_buf_free_head;
+ u64 map;
+
+ while (lrg_buf_cb) {
+ if (!lrg_buf_cb->skb) {
+ lrg_buf_cb->skb = dev_alloc_skb(qdev->lrg_buffer_len);
+ if (unlikely(!lrg_buf_cb->skb)) {
+ printk(KERN_DEBUG PFX
+ "%s: Failed dev_alloc_skb().\n",
+ qdev->ndev->name);
+ break;
+ } else {
+ /*
+ * We save some space to copy the ethhdr from
+ * first buffer
+ */
+ skb_reserve(lrg_buf_cb->skb, QL_HEADER_SPACE);
+ map = pci_map_single(qdev->pdev,
+ lrg_buf_cb->skb->data,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE,
+ PCI_DMA_FROMDEVICE);
+ lrg_buf_cb->buf_phy_addr_low =
+ cpu_to_le32(LS_64BITS(map));
+ lrg_buf_cb->buf_phy_addr_high =
+ cpu_to_le32(MS_64BITS(map));
+ pci_unmap_addr_set(lrg_buf_cb, mapaddr, map);
+ pci_unmap_len_set(lrg_buf_cb, maplen,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE);
+ --qdev->lrg_buf_skb_check;
+ if (!qdev->lrg_buf_skb_check)
+ return 1;
+ }
+ }
+ lrg_buf_cb = lrg_buf_cb->next;
+ }
+ return 0;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static void ql_update_lrg_bufq_prod_index(struct ql3_adapter *qdev)
+{
+ struct bufq_addr_element *lrg_buf_q_ele;
+ int i;
+ struct ql_rcv_buf_cb *lrg_buf_cb;
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+
+ if ((qdev->lrg_buf_free_count >= 8)
+ && (qdev->lrg_buf_release_cnt >= 16)) {
+
+ if (qdev->lrg_buf_skb_check)
+ if (!ql_populate_free_queue(qdev))
+ return;
+
+ lrg_buf_q_ele = qdev->lrg_buf_next_free;
+
+ while ((qdev->lrg_buf_release_cnt >= 16)
+ && (qdev->lrg_buf_free_count >= 8)) {
+
+ for (i = 0; i < 8; i++) {
+ lrg_buf_cb =
+ ql_get_from_lrg_buf_free_list(qdev);
+ lrg_buf_q_ele->addr_high =
+ lrg_buf_cb->buf_phy_addr_high;
+ lrg_buf_q_ele->addr_low =
+ lrg_buf_cb->buf_phy_addr_low;
+ lrg_buf_q_ele++;
+
+ qdev->lrg_buf_release_cnt--;
+ }
+
+ qdev->lrg_buf_q_producer_index++;
+
+ if (qdev->lrg_buf_q_producer_index == NUM_LBUFQ_ENTRIES)
+ qdev->lrg_buf_q_producer_index = 0;
+
+ if (qdev->lrg_buf_q_producer_index ==
+ (NUM_LBUFQ_ENTRIES - 1)) {
+ lrg_buf_q_ele = qdev->lrg_buf_q_virt_addr;
+ }
+ }
+
+ qdev->lrg_buf_next_free = lrg_buf_q_ele;
+
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ rxLargeQProducerIndex,
+ qdev->lrg_buf_q_producer_index);
+ }
+}
+
+static void ql_process_mac_tx_intr(struct ql3_adapter *qdev,
+ struct ob_mac_iocb_rsp *mac_rsp)
+{
+ struct ql_tx_buf_cb *tx_cb;
+
+ tx_cb = &qdev->tx_buf[mac_rsp->transaction_id];
+ pci_unmap_single(qdev->pdev,
+ pci_unmap_addr(tx_cb, mapaddr),
+ pci_unmap_len(tx_cb, maplen), PCI_DMA_TODEVICE);
+ dev_kfree_skb_irq(tx_cb->skb);
+ qdev->stats.tx_packets++;
+ qdev->stats.tx_bytes += tx_cb->skb->len;
+ tx_cb->skb = NULL;
+ atomic_inc(&qdev->tx_count);
+}
+
+static void ql_process_mac_rx_intr(struct ql3_adapter *qdev,
+ struct ib_mac_iocb_rsp *ib_mac_rsp_ptr)
+{
+ long int offset;
+ u32 lrg_buf_phy_addr_low = 0;
+ struct ql_rcv_buf_cb *lrg_buf_cb1 = NULL;
+ struct ql_rcv_buf_cb *lrg_buf_cb2 = NULL;
+ u32 *curr_ial_ptr;
+ struct sk_buff *skb;
+ u16 length = le16_to_cpu(ib_mac_rsp_ptr->length);
+
+ /*
+ * Get the inbound address list (small buffer).
+ */
+ offset = qdev->small_buf_index * QL_SMALL_BUFFER_SIZE;
+ if (++qdev->small_buf_index == NUM_SMALL_BUFFERS)
+ qdev->small_buf_index = 0;
+
+ curr_ial_ptr = (u32 *) (qdev->small_buf_virt_addr + offset);
+ qdev->last_rsp_offset = qdev->small_buf_phy_addr_low + offset;
+ qdev->small_buf_release_cnt++;
+
+ /* start of first buffer */
+ lrg_buf_phy_addr_low = le32_to_cpu(*curr_ial_ptr);
+ lrg_buf_cb1 = &qdev->lrg_buf[qdev->lrg_buf_index];
+ qdev->lrg_buf_release_cnt++;
+ if (++qdev->lrg_buf_index == NUM_LARGE_BUFFERS)
+ qdev->lrg_buf_index = 0;
+ curr_ial_ptr++; /* 64-bit pointers require two incs. */
+ curr_ial_ptr++;
+
+ /* start of second buffer */
+ lrg_buf_phy_addr_low = le32_to_cpu(*curr_ial_ptr);
+ lrg_buf_cb2 = &qdev->lrg_buf[qdev->lrg_buf_index];
+
+ /*
+ * Second buffer gets sent up the stack.
+ */
+ qdev->lrg_buf_release_cnt++;
+ if (++qdev->lrg_buf_index == NUM_LARGE_BUFFERS)
+ qdev->lrg_buf_index = 0;
+ skb = lrg_buf_cb2->skb;
+
+ qdev->stats.rx_packets++;
+ qdev->stats.rx_bytes += length;
+
+ skb_put(skb, length);
+ pci_unmap_single(qdev->pdev,
+ pci_unmap_addr(lrg_buf_cb2, mapaddr),
+ pci_unmap_len(lrg_buf_cb2, maplen),
+ PCI_DMA_FROMDEVICE);
+ prefetch(skb->data);
+ skb->dev = qdev->ndev;
+ skb->ip_summed = CHECKSUM_NONE;
+ skb->protocol = eth_type_trans(skb, qdev->ndev);
+
+ netif_receive_skb(skb);
+ qdev->ndev->last_rx = jiffies;
+ lrg_buf_cb2->skb = NULL;
+
+ ql_release_to_lrg_buf_free_list(qdev, lrg_buf_cb1);
+ ql_release_to_lrg_buf_free_list(qdev, lrg_buf_cb2);
+}
+
+static void ql_process_macip_rx_intr(struct ql3_adapter *qdev,
+ struct ib_ip_iocb_rsp *ib_ip_rsp_ptr)
+{
+ long int offset;
+ u32 lrg_buf_phy_addr_low = 0;
+ struct ql_rcv_buf_cb *lrg_buf_cb1 = NULL;
+ struct ql_rcv_buf_cb *lrg_buf_cb2 = NULL;
+ u32 *curr_ial_ptr;
+ struct sk_buff *skb1, *skb2;
+ struct net_device *ndev = qdev->ndev;
+ u16 length = le16_to_cpu(ib_ip_rsp_ptr->length);
+ u16 size = 0;
+
+ /*
+ * Get the inbound address list (small buffer).
+ */
+
+ offset = qdev->small_buf_index * QL_SMALL_BUFFER_SIZE;
+ if (++qdev->small_buf_index == NUM_SMALL_BUFFERS)
+ qdev->small_buf_index = 0;
+ curr_ial_ptr = (u32 *) (qdev->small_buf_virt_addr + offset);
+ qdev->last_rsp_offset = qdev->small_buf_phy_addr_low + offset;
+ qdev->small_buf_release_cnt++;
+
+ /* start of first buffer */
+ lrg_buf_phy_addr_low = le32_to_cpu(*curr_ial_ptr);
+ lrg_buf_cb1 = &qdev->lrg_buf[qdev->lrg_buf_index];
+
+ qdev->lrg_buf_release_cnt++;
+ if (++qdev->lrg_buf_index == NUM_LARGE_BUFFERS)
+ qdev->lrg_buf_index = 0;
+ skb1 = lrg_buf_cb1->skb;
+ curr_ial_ptr++; /* 64-bit pointers require two incs. */
+ curr_ial_ptr++;
+
+ /* start of second buffer */
+ lrg_buf_phy_addr_low = le32_to_cpu(*curr_ial_ptr);
+ lrg_buf_cb2 = &qdev->lrg_buf[qdev->lrg_buf_index];
+ skb2 = lrg_buf_cb2->skb;
+ qdev->lrg_buf_release_cnt++;
+ if (++qdev->lrg_buf_index == NUM_LARGE_BUFFERS)
+ qdev->lrg_buf_index = 0;
+
+ qdev->stats.rx_packets++;
+ qdev->stats.rx_bytes += length;
+
+ /*
+ * Copy the ethhdr from first buffer to second. This
+ * is necessary for IP completions.
+ */
+ if (*((u16 *) skb1->data) != 0xFFFF)
+ size = VLAN_ETH_HLEN;
+ else
+ size = ETH_HLEN;
+
+ skb_put(skb2, length); /* Just the second buffer length here. */
+ pci_unmap_single(qdev->pdev,
+ pci_unmap_addr(lrg_buf_cb2, mapaddr),
+ pci_unmap_len(lrg_buf_cb2, maplen),
+ PCI_DMA_FROMDEVICE);
+ prefetch(skb2->data);
+
+ memcpy(skb_push(skb2, size), skb1->data + VLAN_ID_LEN, size);
+ skb2->dev = qdev->ndev;
+ skb2->ip_summed = CHECKSUM_NONE;
+ skb2->protocol = eth_type_trans(skb2, qdev->ndev);
+
+ netif_receive_skb(skb2);
+ ndev->last_rx = jiffies;
+ lrg_buf_cb2->skb = NULL;
+
+ ql_release_to_lrg_buf_free_list(qdev, lrg_buf_cb1);
+ ql_release_to_lrg_buf_free_list(qdev, lrg_buf_cb2);
+}
+
+static int ql_tx_rx_clean(struct ql3_adapter *qdev,
+ int *tx_cleaned, int *rx_cleaned, int work_to_do)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ struct net_rsp_iocb *net_rsp;
+ struct net_device *ndev = qdev->ndev;
+ unsigned long hw_flags;
+
+ /* While there are entries in the completion queue. */
+ while ((cpu_to_le32(*(qdev->prsp_producer_index)) !=
+ qdev->rsp_consumer_index) && (*rx_cleaned < work_to_do)) {
+
+ net_rsp = qdev->rsp_current;
+ switch (net_rsp->opcode) {
+
+ case OPCODE_OB_MAC_IOCB_FN0:
+ case OPCODE_OB_MAC_IOCB_FN2:
+ ql_process_mac_tx_intr(qdev, (struct ob_mac_iocb_rsp *)
+ net_rsp);
+ (*tx_cleaned)++;
+ break;
+
+ case OPCODE_IB_MAC_IOCB:
+ ql_process_mac_rx_intr(qdev, (struct ib_mac_iocb_rsp *)
+ net_rsp);
+ (*rx_cleaned)++;
+ break;
+
+ case OPCODE_IB_IP_IOCB:
+ ql_process_macip_rx_intr(qdev, (struct ib_ip_iocb_rsp *)
+ net_rsp);
+ (*rx_cleaned)++;
+ break;
+ default:
+ {
+ u32 *tmp = (u32 *) net_rsp;
+ printk(KERN_ERR PFX
+ "%s: Hit default case, not "
+ "handled!\n"
+ " dropping the packet, opcode = "
+ "%x.\n",
+ ndev->name, net_rsp->opcode);
+ printk(KERN_ERR PFX
+ "0x%08lx 0x%08lx 0x%08lx 0x%08lx \n",
+ (unsigned long int)tmp[0],
+ (unsigned long int)tmp[1],
+ (unsigned long int)tmp[2],
+ (unsigned long int)tmp[3]);
+ }
+ }
+
+ qdev->rsp_consumer_index++;
+
+ if (qdev->rsp_consumer_index == NUM_RSP_Q_ENTRIES) {
+ qdev->rsp_consumer_index = 0;
+ qdev->rsp_current = qdev->rsp_q_virt_addr;
+ } else {
+ qdev->rsp_current++;
+ }
+ }
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+
+ ql_update_lrg_bufq_prod_index(qdev);
+
+ if (qdev->small_buf_release_cnt >= 16) {
+ while (qdev->small_buf_release_cnt >= 16) {
+ qdev->small_buf_q_producer_index++;
+
+ if (qdev->small_buf_q_producer_index ==
+ NUM_SBUFQ_ENTRIES)
+ qdev->small_buf_q_producer_index = 0;
+ qdev->small_buf_release_cnt -= 8;
+ }
+
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ rxSmallQProducerIndex,
+ qdev->small_buf_q_producer_index);
+ }
+
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.rspQConsumerIndex,
+ qdev->rsp_consumer_index);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+ if (unlikely(netif_queue_stopped(qdev->ndev))) {
+ if (netif_queue_stopped(qdev->ndev) &&
+ (atomic_read(&qdev->tx_count) > (NUM_REQ_Q_ENTRIES / 4)))
+ netif_wake_queue(qdev->ndev);
+ }
+
+ return *tx_cleaned + *rx_cleaned;
+}
+
+static int ql_poll(struct net_device *ndev, int *budget)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ int work_to_do = min(*budget, ndev->quota);
+ int rx_cleaned = 0, tx_cleaned = 0;
+
+ if (!netif_carrier_ok(ndev))
+ goto quit_polling;
+
+ ql_tx_rx_clean(qdev, &tx_cleaned, &rx_cleaned, work_to_do);
+ *budget -= rx_cleaned;
+ ndev->quota -= rx_cleaned;
+
+ if ((!tx_cleaned && !rx_cleaned) || !netif_running(ndev)) {
+quit_polling:
+ netif_rx_complete(ndev);
+ ql_enable_interrupts(qdev);
+ return 0;
+ }
+ return 1;
+}
+
+static irqreturn_t ql3xxx_isr(int irq, void *dev_id, struct pt_regs *regs)
+{
+
+ struct net_device *ndev = dev_id;
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ u32 value;
+ int handled = 1;
+ u32 var;
+
+ port_regs = qdev->mem_map_registers;
+
+ value =
+ ql_read_common_reg_l(qdev, &port_regs->CommonRegs.ispControlStatus);
+
+ if (value & (ISP_CONTROL_FE | ISP_CONTROL_RI)) {
+ spin_lock(&qdev->adapter_lock);
+ netif_stop_queue(qdev->ndev);
+ netif_carrier_off(qdev->ndev);
+ ql_disable_interrupts(qdev);
+ qdev->port_link_state = LS_DOWN;
+ set_bit(QL_RESET_ACTIVE,&qdev->flags) ;
+
+ if (value & ISP_CONTROL_FE) {
+ /*
+ * Chip Fatal Error.
+ */
+ var =
+ ql_read_page0_reg_l(qdev,
+ &port_regs->PortFatalErrStatus);
+ printk(KERN_WARNING PFX
+ "%s: Resetting chip. PortFatalErrStatus "
+ "register = 0x%x\n", ndev->name, var);
+ set_bit(QL_RESET_START,&qdev->flags) ;
+ } else {
+ /*
+ * Soft Reset Requested.
+ */
+ set_bit(QL_RESET_PER_SCSI,&qdev->flags) ;
+ printk(KERN_ERR PFX
+ "%s: Another function issued a reset to the "
+ "chip. ISR value = %x.\n", ndev->name, value);
+ }
+ queue_work(qdev->workqueue, &qdev->reset_work);
+ spin_unlock(&qdev->adapter_lock);
+ } else if (value & ISP_IMR_DISABLE_CMPL_INT) {
+ ql_disable_interrupts(qdev);
+ if (likely(netif_rx_schedule_prep(ndev)))
+ __netif_rx_schedule(ndev);
+ else
+ ql_enable_interrupts(qdev);
+ } else {
+ return IRQ_NONE;
+ }
+
+ return IRQ_RETVAL(handled);
+}
+
+static int ql3xxx_send(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)netdev_priv(ndev);
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ struct ql_tx_buf_cb *tx_cb;
+ struct ob_mac_iocb_req *mac_iocb_ptr;
+ u64 map;
+
+ if (unlikely(atomic_read(&qdev->tx_count) < 2)) {
+ if (!netif_queue_stopped(ndev))
+ netif_stop_queue(ndev);
+ return NETDEV_TX_BUSY;
+ }
+ tx_cb = &qdev->tx_buf[qdev->req_producer_index] ;
+ mac_iocb_ptr = tx_cb->queue_entry;
+ memset((void *)mac_iocb_ptr, 0, sizeof(struct ob_mac_iocb_req));
+ mac_iocb_ptr->opcode = qdev->mac_ob_opcode;
+ mac_iocb_ptr->flags |= qdev->mb_bit_mask;
+ mac_iocb_ptr->transaction_id = qdev->req_producer_index;
+ mac_iocb_ptr->data_len = cpu_to_le16((u16) skb->len);
+ tx_cb->skb = skb;
+ map = pci_map_single(qdev->pdev, skb->data, skb->len, PCI_DMA_TODEVICE);
+ mac_iocb_ptr->buf_addr0_low = cpu_to_le32(LS_64BITS(map));
+ mac_iocb_ptr->buf_addr0_high = cpu_to_le32(MS_64BITS(map));
+ mac_iocb_ptr->buf_0_len = cpu_to_le32(skb->len | OB_MAC_IOCB_REQ_E);
+ pci_unmap_addr_set(tx_cb, mapaddr, map);
+ pci_unmap_len_set(tx_cb, maplen, skb->len);
+ atomic_dec(&qdev->tx_count);
+
+ qdev->req_producer_index++;
+ if (qdev->req_producer_index == NUM_REQ_Q_ENTRIES)
+ qdev->req_producer_index = 0;
+ wmb();
+ ql_write_common_reg_l(qdev,
+ (u32 *) & port_regs->CommonRegs.reqQProducerIndex,
+ qdev->req_producer_index);
+
+ ndev->trans_start = jiffies;
+ if (netif_msg_tx_queued(qdev))
+ printk(KERN_DEBUG PFX "%s: tx queued, slot %d, len %d\n",
+ ndev->name, qdev->req_producer_index, skb->len);
+
+ return NETDEV_TX_OK;
+}
+static int ql_alloc_net_req_rsp_queues(struct ql3_adapter *qdev)
+{
+ qdev->req_q_size =
+ (u32) (NUM_REQ_Q_ENTRIES * sizeof(struct ob_mac_iocb_req));
+
+ qdev->req_q_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ (size_t) qdev->req_q_size,
+ &qdev->req_q_phy_addr);
+
+ if ((qdev->req_q_virt_addr == NULL) ||
+ LS_64BITS(qdev->req_q_phy_addr) & (qdev->req_q_size - 1)) {
+ printk(KERN_ERR PFX "%s: reqQ failed.\n",
+ qdev->ndev->name);
+ return -ENOMEM;
+ }
+
+ qdev->rsp_q_size = NUM_RSP_Q_ENTRIES * sizeof(struct net_rsp_iocb);
+
+ qdev->rsp_q_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ (size_t) qdev->rsp_q_size,
+ &qdev->rsp_q_phy_addr);
+
+ if ((qdev->rsp_q_virt_addr == NULL) ||
+ LS_64BITS(qdev->rsp_q_phy_addr) & (qdev->rsp_q_size - 1)) {
+ printk(KERN_ERR PFX
+ "%s: rspQ allocation failed\n",
+ qdev->ndev->name);
+ pci_free_consistent(qdev->pdev, (size_t) qdev->req_q_size,
+ qdev->req_q_virt_addr,
+ qdev->req_q_phy_addr);
+ return -ENOMEM;
+ }
+
+ set_bit(QL_ALLOC_REQ_RSP_Q_DONE,&qdev->flags);
+
+ return 0;
+}
+
+static void ql_free_net_req_rsp_queues(struct ql3_adapter *qdev)
+{
+ if (!test_bit(QL_ALLOC_REQ_RSP_Q_DONE,&qdev->flags)) {
+ printk(KERN_INFO PFX
+ "%s: Already done.\n", qdev->ndev->name);
+ return;
+ }
+
+ pci_free_consistent(qdev->pdev,
+ qdev->req_q_size,
+ qdev->req_q_virt_addr, qdev->req_q_phy_addr);
+
+ qdev->req_q_virt_addr = NULL;
+
+ pci_free_consistent(qdev->pdev,
+ qdev->rsp_q_size,
+ qdev->rsp_q_virt_addr, qdev->rsp_q_phy_addr);
+
+ qdev->rsp_q_virt_addr = NULL;
+
+ clear_bit(QL_ALLOC_REQ_RSP_Q_DONE,&qdev->flags);
+}
+
+static int ql_alloc_buffer_queues(struct ql3_adapter *qdev)
+{
+ /* Create Large Buffer Queue */
+ qdev->lrg_buf_q_size =
+ NUM_LBUFQ_ENTRIES * sizeof(struct lrg_buf_q_entry);
+ if (qdev->lrg_buf_q_size < PAGE_SIZE)
+ qdev->lrg_buf_q_alloc_size = PAGE_SIZE;
+ else
+ qdev->lrg_buf_q_alloc_size = qdev->lrg_buf_q_size * 2;
+
+ qdev->lrg_buf_q_alloc_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ qdev->lrg_buf_q_alloc_size,
+ &qdev->lrg_buf_q_alloc_phy_addr);
+
+ if (qdev->lrg_buf_q_alloc_virt_addr == NULL) {
+ printk(KERN_ERR PFX
+ "%s: lBufQ failed\n", qdev->ndev->name);
+ return -ENOMEM;
+ }
+ qdev->lrg_buf_q_virt_addr = qdev->lrg_buf_q_alloc_virt_addr;
+ qdev->lrg_buf_q_phy_addr = qdev->lrg_buf_q_alloc_phy_addr;
+
+ /* Create Small Buffer Queue */
+ qdev->small_buf_q_size =
+ NUM_SBUFQ_ENTRIES * sizeof(struct lrg_buf_q_entry);
+ if (qdev->small_buf_q_size < PAGE_SIZE)
+ qdev->small_buf_q_alloc_size = PAGE_SIZE;
+ else
+ qdev->small_buf_q_alloc_size = qdev->small_buf_q_size * 2;
+
+ qdev->small_buf_q_alloc_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ qdev->small_buf_q_alloc_size,
+ &qdev->small_buf_q_alloc_phy_addr);
+
+ if (qdev->small_buf_q_alloc_virt_addr == NULL) {
+ printk(KERN_ERR PFX
+ "%s: Small Buffer Queue allocation failed.\n",
+ qdev->ndev->name);
+ pci_free_consistent(qdev->pdev, qdev->lrg_buf_q_alloc_size,
+ qdev->lrg_buf_q_alloc_virt_addr,
+ qdev->lrg_buf_q_alloc_phy_addr);
+ return -ENOMEM;
+ }
+
+ qdev->small_buf_q_virt_addr = qdev->small_buf_q_alloc_virt_addr;
+ qdev->small_buf_q_phy_addr = qdev->small_buf_q_alloc_phy_addr;
+ set_bit(QL_ALLOC_BUFQS_DONE,&qdev->flags);
+ return 0;
+}
+
+static void ql_free_buffer_queues(struct ql3_adapter *qdev)
+{
+ if (!test_bit(QL_ALLOC_BUFQS_DONE,&qdev->flags)) {
+ printk(KERN_INFO PFX
+ "%s: Already done.\n", qdev->ndev->name);
+ return;
+ }
+
+ pci_free_consistent(qdev->pdev,
+ qdev->lrg_buf_q_alloc_size,
+ qdev->lrg_buf_q_alloc_virt_addr,
+ qdev->lrg_buf_q_alloc_phy_addr);
+
+ qdev->lrg_buf_q_virt_addr = NULL;
+
+ pci_free_consistent(qdev->pdev,
+ qdev->small_buf_q_alloc_size,
+ qdev->small_buf_q_alloc_virt_addr,
+ qdev->small_buf_q_alloc_phy_addr);
+
+ qdev->small_buf_q_virt_addr = NULL;
+
+ clear_bit(QL_ALLOC_BUFQS_DONE,&qdev->flags);
+}
+
+static int ql_alloc_small_buffers(struct ql3_adapter *qdev)
+{
+ int i;
+ struct bufq_addr_element *small_buf_q_entry;
+
+ /* Currently we allocate on one of memory and use it for smallbuffers */
+ qdev->small_buf_total_size =
+ (QL_ADDR_ELE_PER_BUFQ_ENTRY * NUM_SBUFQ_ENTRIES *
+ QL_SMALL_BUFFER_SIZE);
+
+ qdev->small_buf_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ qdev->small_buf_total_size,
+ &qdev->small_buf_phy_addr);
+
+ if (qdev->small_buf_virt_addr == NULL) {
+ printk(KERN_ERR PFX
+ "%s: Failed to get small buffer memory.\n",
+ qdev->ndev->name);
+ return -ENOMEM;
+ }
+
+ qdev->small_buf_phy_addr_low = LS_64BITS(qdev->small_buf_phy_addr);
+ qdev->small_buf_phy_addr_high = MS_64BITS(qdev->small_buf_phy_addr);
+
+ small_buf_q_entry = qdev->small_buf_q_virt_addr;
+
+ qdev->last_rsp_offset = qdev->small_buf_phy_addr_low;
+
+ /* Initialize the small buffer queue. */
+ for (i = 0; i < (QL_ADDR_ELE_PER_BUFQ_ENTRY * NUM_SBUFQ_ENTRIES); i++) {
+ small_buf_q_entry->addr_high =
+ cpu_to_le32(qdev->small_buf_phy_addr_high);
+ small_buf_q_entry->addr_low =
+ cpu_to_le32(qdev->small_buf_phy_addr_low +
+ (i * QL_SMALL_BUFFER_SIZE));
+ small_buf_q_entry++;
+ }
+ qdev->small_buf_index = 0;
+ set_bit(QL_ALLOC_SMALL_BUF_DONE,&qdev->flags);
+ return 0;
+}
+
+static void ql_free_small_buffers(struct ql3_adapter *qdev)
+{
+ if (!test_bit(QL_ALLOC_SMALL_BUF_DONE,&qdev->flags)) {
+ printk(KERN_INFO PFX
+ "%s: Already done.\n", qdev->ndev->name);
+ return;
+ }
+ if (qdev->small_buf_virt_addr != NULL) {
+ pci_free_consistent(qdev->pdev,
+ qdev->small_buf_total_size,
+ qdev->small_buf_virt_addr,
+ qdev->small_buf_phy_addr);
+
+ qdev->small_buf_virt_addr = NULL;
+ }
+}
+
+static void ql_free_large_buffers(struct ql3_adapter *qdev)
+{
+ int i = 0;
+ struct ql_rcv_buf_cb *lrg_buf_cb;
+
+ for (i = 0; i < NUM_LARGE_BUFFERS; i++) {
+ lrg_buf_cb = &qdev->lrg_buf[i];
+ if (lrg_buf_cb->skb) {
+ dev_kfree_skb(lrg_buf_cb->skb);
+ pci_unmap_single(qdev->pdev,
+ pci_unmap_addr(lrg_buf_cb, mapaddr),
+ pci_unmap_len(lrg_buf_cb, maplen),
+ PCI_DMA_FROMDEVICE);
+ memset(lrg_buf_cb, 0, sizeof(struct ql_rcv_buf_cb));
+ } else {
+ break;
+ }
+ }
+}
+
+static void ql_init_large_buffers(struct ql3_adapter *qdev)
+{
+ int i;
+ struct ql_rcv_buf_cb *lrg_buf_cb;
+ struct bufq_addr_element *buf_addr_ele = qdev->lrg_buf_q_virt_addr;
+
+ for (i = 0; i < NUM_LARGE_BUFFERS; i++) {
+ lrg_buf_cb = &qdev->lrg_buf[i];
+ buf_addr_ele->addr_high = lrg_buf_cb->buf_phy_addr_high;
+ buf_addr_ele->addr_low = lrg_buf_cb->buf_phy_addr_low;
+ buf_addr_ele++;
+ }
+ qdev->lrg_buf_index = 0;
+ qdev->lrg_buf_skb_check = 0;
+}
+
+static int ql_alloc_large_buffers(struct ql3_adapter *qdev)
+{
+ int i;
+ struct ql_rcv_buf_cb *lrg_buf_cb;
+ struct sk_buff *skb;
+ u64 map;
+
+ for (i = 0; i < NUM_LARGE_BUFFERS; i++) {
+ skb = dev_alloc_skb(qdev->lrg_buffer_len);
+ if (unlikely(!skb)) {
+ /* Better luck next round */
+ printk(KERN_ERR PFX
+ "%s: large buff alloc failed, "
+ "for %d bytes at index %d.\n",
+ qdev->ndev->name,
+ qdev->lrg_buffer_len * 2, i);
+ ql_free_large_buffers(qdev);
+ return -ENOMEM;
+ } else {
+
+ lrg_buf_cb = &qdev->lrg_buf[i];
+ memset(lrg_buf_cb, 0, sizeof(struct ql_rcv_buf_cb));
+ lrg_buf_cb->index = i;
+ lrg_buf_cb->skb = skb;
+ /*
+ * We save some space to copy the ethhdr from first
+ * buffer
+ */
+ skb_reserve(skb, QL_HEADER_SPACE);
+ map = pci_map_single(qdev->pdev,
+ skb->data,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE,
+ PCI_DMA_FROMDEVICE);
+ pci_unmap_addr_set(lrg_buf_cb, mapaddr, map);
+ pci_unmap_len_set(lrg_buf_cb, maplen,
+ qdev->lrg_buffer_len -
+ QL_HEADER_SPACE);
+ lrg_buf_cb->buf_phy_addr_low =
+ cpu_to_le32(LS_64BITS(map));
+ lrg_buf_cb->buf_phy_addr_high =
+ cpu_to_le32(MS_64BITS(map));
+ }
+ }
+ return 0;
+}
+
+static void ql_create_send_free_list(struct ql3_adapter *qdev)
+{
+ struct ql_tx_buf_cb *tx_cb;
+ int i;
+ struct ob_mac_iocb_req *req_q_curr =
+ qdev->req_q_virt_addr;
+
+ /* Create free list of transmit buffers */
+ for (i = 0; i < NUM_REQ_Q_ENTRIES; i++) {
+ tx_cb = &qdev->tx_buf[i];
+ tx_cb->skb = NULL;
+ tx_cb->queue_entry = req_q_curr;
+ req_q_curr++;
+ }
+}
+
+static int ql_alloc_mem_resources(struct ql3_adapter *qdev)
+{
+ if (qdev->ndev->mtu == NORMAL_MTU_SIZE)
+ qdev->lrg_buffer_len = NORMAL_MTU_SIZE;
+ else if (qdev->ndev->mtu == JUMBO_MTU_SIZE) {
+ qdev->lrg_buffer_len = JUMBO_MTU_SIZE;
+ } else {
+ printk(KERN_ERR PFX
+ "%s: Invalid mtu size. Only 1500 and 9000 are accepted.\n",
+ qdev->ndev->name);
+ return -ENOMEM;
+ }
+ qdev->lrg_buffer_len += VLAN_ETH_HLEN + VLAN_ID_LEN + QL_HEADER_SPACE;
+ qdev->max_frame_size =
+ (qdev->lrg_buffer_len - QL_HEADER_SPACE) + ETHERNET_CRC_SIZE;
+
+ /*
+ * First allocate a page of shared memory and use it for shadow
+ * locations of Network Request Queue Consumer Address Register and
+ * Network Completion Queue Producer Index Register
+ */
+ qdev->shadow_reg_virt_addr =
+ pci_alloc_consistent(qdev->pdev,
+ PAGE_SIZE, &qdev->shadow_reg_phy_addr);
+
+ if (qdev->shadow_reg_virt_addr != NULL) {
+ qdev->preq_consumer_index = (u16 *) qdev->shadow_reg_virt_addr;
+ qdev->req_consumer_index_phy_addr_high =
+ MS_64BITS(qdev->shadow_reg_phy_addr);
+ qdev->req_consumer_index_phy_addr_low =
+ LS_64BITS(qdev->shadow_reg_phy_addr);
+
+ qdev->prsp_producer_index =
+ (u32 *) (((u8 *) qdev->preq_consumer_index) + 8);
+ qdev->rsp_producer_index_phy_addr_high =
+ qdev->req_consumer_index_phy_addr_high;
+ qdev->rsp_producer_index_phy_addr_low =
+ qdev->req_consumer_index_phy_addr_low + 8;
+ } else {
+ printk(KERN_ERR PFX
+ "%s: shadowReg Alloc failed.\n", qdev->ndev->name);
+ return -ENOMEM;
+ }
+
+ if (ql_alloc_net_req_rsp_queues(qdev) != 0) {
+ printk(KERN_ERR PFX
+ "%s: ql_alloc_net_req_rsp_queues failed.\n",
+ qdev->ndev->name);
+ goto err_req_rsp;
+ }
+
+ if (ql_alloc_buffer_queues(qdev) != 0) {
+ printk(KERN_ERR PFX
+ "%s: ql_alloc_buffer_queues failed.\n",
+ qdev->ndev->name);
+ goto err_buffer_queues;
+ }
+
+ if (ql_alloc_small_buffers(qdev) != 0) {
+ printk(KERN_ERR PFX
+ "%s: ql_alloc_small_buffers failed\n", qdev->ndev->name);
+ goto err_small_buffers;
+ }
+
+ if (ql_alloc_large_buffers(qdev) != 0) {
+ printk(KERN_ERR PFX
+ "%s: ql_alloc_large_buffers failed\n", qdev->ndev->name);
+ goto err_small_buffers;
+ }
+
+ /* Initialize the large buffer queue. */
+ ql_init_large_buffers(qdev);
+ ql_create_send_free_list(qdev);
+
+ qdev->rsp_current = qdev->rsp_q_virt_addr;
+
+ return 0;
+
+err_small_buffers:
+ ql_free_buffer_queues(qdev);
+err_buffer_queues:
+ ql_free_net_req_rsp_queues(qdev);
+err_req_rsp:
+ pci_free_consistent(qdev->pdev,
+ PAGE_SIZE,
+ qdev->shadow_reg_virt_addr,
+ qdev->shadow_reg_phy_addr);
+
+ return -ENOMEM;
+}
+
+static void ql_free_mem_resources(struct ql3_adapter *qdev)
+{
+ ql_free_large_buffers(qdev);
+ ql_free_small_buffers(qdev);
+ ql_free_buffer_queues(qdev);
+ ql_free_net_req_rsp_queues(qdev);
+ if (qdev->shadow_reg_virt_addr != NULL) {
+ pci_free_consistent(qdev->pdev,
+ PAGE_SIZE,
+ qdev->shadow_reg_virt_addr,
+ qdev->shadow_reg_phy_addr);
+ qdev->shadow_reg_virt_addr = NULL;
+ }
+}
+
+static int ql_init_misc_registers(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_local_ram_registers *local_ram =
+ (struct ql3xxx_local_ram_registers *)qdev->mem_map_registers;
+
+ if(ql_sem_spinlock(qdev, QL_DDR_RAM_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 4))
+ return -1;
+
+ ql_write_page2_reg(qdev,
+ &local_ram->bufletSize, qdev->nvram_data.bufletSize);
+
+ ql_write_page2_reg(qdev,
+ &local_ram->maxBufletCount,
+ qdev->nvram_data.bufletCount);
+
+ ql_write_page2_reg(qdev,
+ &local_ram->freeBufletThresholdLow,
+ (qdev->nvram_data.tcpWindowThreshold25 << 16) |
+ (qdev->nvram_data.tcpWindowThreshold0));
+
+ ql_write_page2_reg(qdev,
+ &local_ram->freeBufletThresholdHigh,
+ qdev->nvram_data.tcpWindowThreshold50);
+
+ ql_write_page2_reg(qdev,
+ &local_ram->ipHashTableBase,
+ (qdev->nvram_data.ipHashTableBaseHi << 16) |
+ qdev->nvram_data.ipHashTableBaseLo);
+ ql_write_page2_reg(qdev,
+ &local_ram->ipHashTableCount,
+ qdev->nvram_data.ipHashTableSize);
+ ql_write_page2_reg(qdev,
+ &local_ram->tcpHashTableBase,
+ (qdev->nvram_data.tcpHashTableBaseHi << 16) |
+ qdev->nvram_data.tcpHashTableBaseLo);
+ ql_write_page2_reg(qdev,
+ &local_ram->tcpHashTableCount,
+ qdev->nvram_data.tcpHashTableSize);
+ ql_write_page2_reg(qdev,
+ &local_ram->ncbBase,
+ (qdev->nvram_data.ncbTableBaseHi << 16) |
+ qdev->nvram_data.ncbTableBaseLo);
+ ql_write_page2_reg(qdev,
+ &local_ram->maxNcbCount,
+ qdev->nvram_data.ncbTableSize);
+ ql_write_page2_reg(qdev,
+ &local_ram->drbBase,
+ (qdev->nvram_data.drbTableBaseHi << 16) |
+ qdev->nvram_data.drbTableBaseLo);
+ ql_write_page2_reg(qdev,
+ &local_ram->maxDrbCount,
+ qdev->nvram_data.drbTableSize);
+ ql_sem_unlock(qdev, QL_DDR_RAM_SEM_MASK);
+ return 0;
+}
+
+static int ql_adapter_initialize(struct ql3_adapter *qdev)
+{
+ u32 value;
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ struct ql3xxx_host_memory_registers __iomem *hmem_regs =
+ (struct ql3xxx_host_memory_registers *)port_regs;
+ u32 delay = 10;
+ int status = 0;
+
+ if(ql_mii_setup(qdev))
+ return -1;
+
+ /* Bring out PHY out of reset */
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ (ISP_SERIAL_PORT_IF_WE |
+ (ISP_SERIAL_PORT_IF_WE << 16)));
+
+ qdev->port_link_state = LS_DOWN;
+ netif_carrier_off(qdev->ndev);
+
+ /* V2 chip fix for ARS-39168. */
+ ql_write_common_reg(qdev, &port_regs->CommonRegs.serialPortInterfaceReg,
+ (ISP_SERIAL_PORT_IF_SDE |
+ (ISP_SERIAL_PORT_IF_SDE << 16)));
+
+ /* Request Queue Registers */
+ *((u32 *) (qdev->preq_consumer_index)) = 0;
+ atomic_set(&qdev->tx_count,NUM_REQ_Q_ENTRIES);
+ qdev->req_producer_index = 0;
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->reqConsumerIndexAddrHigh,
+ qdev->req_consumer_index_phy_addr_high);
+ ql_write_page1_reg(qdev,
+ &hmem_regs->reqConsumerIndexAddrLow,
+ qdev->req_consumer_index_phy_addr_low);
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->reqBaseAddrHigh,
+ MS_64BITS(qdev->req_q_phy_addr));
+ ql_write_page1_reg(qdev,
+ &hmem_regs->reqBaseAddrLow,
+ LS_64BITS(qdev->req_q_phy_addr));
+ ql_write_page1_reg(qdev, &hmem_regs->reqLength, NUM_REQ_Q_ENTRIES);
+
+ /* Response Queue Registers */
+ *((u16 *) (qdev->prsp_producer_index)) = 0;
+ qdev->rsp_consumer_index = 0;
+ qdev->rsp_current = qdev->rsp_q_virt_addr;
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rspProducerIndexAddrHigh,
+ qdev->rsp_producer_index_phy_addr_high);
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rspProducerIndexAddrLow,
+ qdev->rsp_producer_index_phy_addr_low);
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rspBaseAddrHigh,
+ MS_64BITS(qdev->rsp_q_phy_addr));
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rspBaseAddrLow,
+ LS_64BITS(qdev->rsp_q_phy_addr));
+
+ ql_write_page1_reg(qdev, &hmem_regs->rspLength, NUM_RSP_Q_ENTRIES);
+
+ /* Large Buffer Queue */
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxLargeQBaseAddrHigh,
+ MS_64BITS(qdev->lrg_buf_q_phy_addr));
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxLargeQBaseAddrLow,
+ LS_64BITS(qdev->lrg_buf_q_phy_addr));
+
+ ql_write_page1_reg(qdev, &hmem_regs->rxLargeQLength, NUM_LBUFQ_ENTRIES);
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxLargeBufferLength,
+ qdev->lrg_buffer_len);
+
+ /* Small Buffer Queue */
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxSmallQBaseAddrHigh,
+ MS_64BITS(qdev->small_buf_q_phy_addr));
+
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxSmallQBaseAddrLow,
+ LS_64BITS(qdev->small_buf_q_phy_addr));
+
+ ql_write_page1_reg(qdev, &hmem_regs->rxSmallQLength, NUM_SBUFQ_ENTRIES);
+ ql_write_page1_reg(qdev,
+ &hmem_regs->rxSmallBufferLength,
+ QL_SMALL_BUFFER_SIZE);
+
+ qdev->small_buf_q_producer_index = NUM_SBUFQ_ENTRIES - 1;
+ qdev->small_buf_release_cnt = 8;
+ qdev->lrg_buf_q_producer_index = NUM_LBUFQ_ENTRIES - 1;
+ qdev->lrg_buf_release_cnt = 8;
+ qdev->lrg_buf_next_free =
+ (struct bufq_addr_element *)qdev->lrg_buf_q_virt_addr;
+ qdev->small_buf_index = 0;
+ qdev->lrg_buf_index = 0;
+ qdev->lrg_buf_free_count = 0;
+ qdev->lrg_buf_free_head = NULL;
+ qdev->lrg_buf_free_tail = NULL;
+
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ rxSmallQProducerIndex,
+ qdev->small_buf_q_producer_index);
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ rxLargeQProducerIndex,
+ qdev->lrg_buf_q_producer_index);
+
+ /*
+ * Find out if the chip has already been initialized. If it has, then
+ * we skip some of the initialization.
+ */
+ clear_bit(QL_LINK_MASTER, &qdev->flags);
+ value = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ if ((value & PORT_STATUS_IC) == 0) {
+
+ /* Chip has not been configured yet, so let it rip. */
+ if(ql_init_misc_registers(qdev)) {
+ status = -1;
+ goto out;
+ }
+
+ if (qdev->mac_index)
+ ql_write_page0_reg(qdev,
+ &port_regs->mac1MaxFrameLengthReg,
+ qdev->max_frame_size);
+ else
+ ql_write_page0_reg(qdev,
+ &port_regs->mac0MaxFrameLengthReg,
+ qdev->max_frame_size);
+
+ value = qdev->nvram_data.tcpMaxWindowSize;
+ ql_write_page0_reg(qdev, &port_regs->tcpMaxWindow, value);
+
+ value = (0xFFFF << 16) | qdev->nvram_data.extHwConfig;
+
+ if(ql_sem_spinlock(qdev, QL_FLASH_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index)
+ * 2) << 13)) {
+ status = -1;
+ goto out;
+ }
+ ql_write_page0_reg(qdev, &port_regs->ExternalHWConfig, value);
+ ql_write_page0_reg(qdev, &port_regs->InternalChipConfig,
+ (((INTERNAL_CHIP_SD | INTERNAL_CHIP_WE) <<
+ 16) | (INTERNAL_CHIP_SD |
+ INTERNAL_CHIP_WE)));
+ ql_sem_unlock(qdev, QL_FLASH_SEM_MASK);
+ }
+
+
+ if(ql_sem_spinlock(qdev, QL_PHY_GIO_SEM_MASK,
+ (QL_RESOURCE_BITS_BASE_CODE | (qdev->mac_index) *
+ 2) << 7)) {
+ status = -1;
+ goto out;
+ }
+
+ ql_init_scan_mode(qdev);
+ ql_get_phy_owner(qdev);
+
+ /* Load the MAC Configuration */
+
+ /* Program lower 32 bits of the MAC address */
+ ql_write_page0_reg(qdev, &port_regs->macAddrIndirectPtrReg,
+ (MAC_ADDR_INDIRECT_PTR_REG_RP_MASK << 16));
+ ql_write_page0_reg(qdev, &port_regs->macAddrDataReg,
+ ((qdev->ndev->dev_addr[2] << 24)
+ | (qdev->ndev->dev_addr[3] << 16)
+ | (qdev->ndev->dev_addr[4] << 8)
+ | qdev->ndev->dev_addr[5]));
+
+ /* Program top 16 bits of the MAC address */
+ ql_write_page0_reg(qdev, &port_regs->macAddrIndirectPtrReg,
+ ((MAC_ADDR_INDIRECT_PTR_REG_RP_MASK << 16) | 1));
+ ql_write_page0_reg(qdev, &port_regs->macAddrDataReg,
+ ((qdev->ndev->dev_addr[0] << 8)
+ | qdev->ndev->dev_addr[1]));
+
+ /* Enable Primary MAC */
+ ql_write_page0_reg(qdev, &port_regs->macAddrIndirectPtrReg,
+ ((MAC_ADDR_INDIRECT_PTR_REG_PE << 16) |
+ MAC_ADDR_INDIRECT_PTR_REG_PE));
+
+ /* Clear Primary and Secondary IP addresses */
+ ql_write_page0_reg(qdev, &port_regs->ipAddrIndexReg,
+ ((IP_ADDR_INDEX_REG_MASK << 16) |
+ (qdev->mac_index << 2)));
+ ql_write_page0_reg(qdev, &port_regs->ipAddrDataReg, 0);
+
+ ql_write_page0_reg(qdev, &port_regs->ipAddrIndexReg,
+ ((IP_ADDR_INDEX_REG_MASK << 16) |
+ ((qdev->mac_index << 2) + 1)));
+ ql_write_page0_reg(qdev, &port_regs->ipAddrDataReg, 0);
+
+ ql_sem_unlock(qdev, QL_PHY_GIO_SEM_MASK);
+
+ /* Indicate Configuration Complete */
+ ql_write_page0_reg(qdev,
+ &port_regs->portControl,
+ ((PORT_CONTROL_CC << 16) | PORT_CONTROL_CC));
+
+ do {
+ value = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ if (value & PORT_STATUS_IC)
+ break;
+ msleep(500);
+ } while (--delay);
+
+ if (delay == 0) {
+ printk(KERN_ERR PFX
+ "%s: Hw Initialization timeout.\n", qdev->ndev->name);
+ status = -1;
+ goto out;
+ }
+
+ /* Enable Ethernet Function */
+ value =
+ (PORT_CONTROL_EF | PORT_CONTROL_ET | PORT_CONTROL_EI |
+ PORT_CONTROL_HH);
+ ql_write_page0_reg(qdev, &port_regs->portControl,
+ ((value << 16) | value));
+
+out:
+ return status;
+}
+
+/*
+ * Caller holds hw_lock.
+ */
+static int ql_adapter_reset(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ int status = 0;
+ u16 value;
+ int max_wait_time;
+
+ set_bit(QL_RESET_ACTIVE, &qdev->flags);
+ clear_bit(QL_RESET_DONE, &qdev->flags);
+
+ /*
+ * Issue soft reset to chip.
+ */
+ printk(KERN_DEBUG PFX
+ "%s: Issue soft reset to chip.\n",
+ qdev->ndev->name);
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.ispControlStatus,
+ ((ISP_CONTROL_SR << 16) | ISP_CONTROL_SR));
+
+ /* Wait 3 seconds for reset to complete. */
+ printk(KERN_DEBUG PFX
+ "%s: Wait 10 milliseconds for reset to complete.\n",
+ qdev->ndev->name);
+
+ /* Wait until the firmware tells us the Soft Reset is done */
+ max_wait_time = 5;
+ do {
+ value =
+ ql_read_common_reg(qdev,
+ &port_regs->CommonRegs.ispControlStatus);
+ if ((value & ISP_CONTROL_SR) == 0)
+ break;
+
+ ssleep(1);
+ } while ((--max_wait_time));
+
+ /*
+ * Also, make sure that the Network Reset Interrupt bit has been
+ * cleared after the soft reset has taken place.
+ */
+ value =
+ ql_read_common_reg(qdev, &port_regs->CommonRegs.ispControlStatus);
+ if (value & ISP_CONTROL_RI) {
+ printk(KERN_DEBUG PFX
+ "ql_adapter_reset: clearing RI after reset.\n");
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ ispControlStatus,
+ ((ISP_CONTROL_RI << 16) | ISP_CONTROL_RI));
+ }
+
+ if (max_wait_time == 0) {
+ /* Issue Force Soft Reset */
+ ql_write_common_reg(qdev,
+ (u32 *) & port_regs->CommonRegs.
+ ispControlStatus,
+ ((ISP_CONTROL_FSR << 16) |
+ ISP_CONTROL_FSR));
+ /*
+ * Wait until the firmware tells us the Force Soft Reset is
+ * done
+ */
+ max_wait_time = 5;
+ do {
+ value =
+ ql_read_common_reg(qdev,
+ &port_regs->CommonRegs.
+ ispControlStatus);
+ if ((value & ISP_CONTROL_FSR) == 0) {
+ break;
+ }
+ ssleep(1);
+ } while ((--max_wait_time));
+ }
+ if (max_wait_time == 0)
+ status = 1;
+
+ clear_bit(QL_RESET_ACTIVE, &qdev->flags);
+ set_bit(QL_RESET_DONE, &qdev->flags);
+ return status;
+}
+
+static void ql_set_mac_info(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ u32 value, port_status;
+ u8 func_number;
+
+ /* Get the function number */
+ value =
+ ql_read_common_reg_l(qdev, &port_regs->CommonRegs.ispControlStatus);
+ func_number = (u8) ((value >> 4) & OPCODE_FUNC_ID_MASK);
+ port_status = ql_read_page0_reg(qdev, &port_regs->portStatus);
+ switch (value & ISP_CONTROL_FN_MASK) {
+ case ISP_CONTROL_FN0_NET:
+ qdev->mac_index = 0;
+ qdev->mac_ob_opcode = OUTBOUND_MAC_IOCB | func_number;
+ qdev->tcp_ob_opcode = OUTBOUND_TCP_IOCB | func_number;
+ qdev->update_ob_opcode = UPDATE_NCB_IOCB | func_number;
+ qdev->mb_bit_mask = FN0_MA_BITS_MASK;
+ qdev->PHYAddr = PORT0_PHY_ADDRESS;
+ if (port_status & PORT_STATUS_SM0)
+ set_bit(QL_LINK_OPTICAL,&qdev->flags);
+ else
+ clear_bit(QL_LINK_OPTICAL,&qdev->flags);
+ break;
+
+ case ISP_CONTROL_FN1_NET:
+ qdev->mac_index = 1;
+ qdev->mac_ob_opcode = OUTBOUND_MAC_IOCB | func_number;
+ qdev->tcp_ob_opcode = OUTBOUND_TCP_IOCB | func_number;
+ qdev->update_ob_opcode = UPDATE_NCB_IOCB | func_number;
+ qdev->mb_bit_mask = FN1_MA_BITS_MASK;
+ qdev->PHYAddr = PORT1_PHY_ADDRESS;
+ if (port_status & PORT_STATUS_SM1)
+ set_bit(QL_LINK_OPTICAL,&qdev->flags);
+ else
+ clear_bit(QL_LINK_OPTICAL,&qdev->flags);
+ break;
+
+ case ISP_CONTROL_FN0_SCSI:
+ case ISP_CONTROL_FN1_SCSI:
+ default:
+ printk(KERN_DEBUG PFX
+ "%s: Invalid function number, ispControlStatus = 0x%x\n",
+ qdev->ndev->name,value);
+ break;
+ }
+ qdev->numPorts = qdev->nvram_data.numPorts;
+}
+
+static void ql_display_dev_info(struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)netdev_priv(ndev);
+ struct pci_dev *pdev = qdev->pdev;
+
+ printk(KERN_INFO PFX
+ "\n%s Adapter %d RevisionID %d found on PCI slot %d.\n",
+ DRV_NAME, qdev->index, qdev->chip_rev_id, qdev->pci_slot);
+ printk(KERN_INFO PFX
+ "%s Interface.\n",
+ test_bit(QL_LINK_OPTICAL,&qdev->flags) ? "OPTICAL" : "COPPER");
+
+ /*
+ * Print PCI bus width/type.
+ */
+ printk(KERN_INFO PFX
+ "Bus interface is %s %s.\n",
+ ((qdev->pci_width == 64) ? "64-bit" : "32-bit"),
+ ((qdev->pci_x) ? "PCI-X" : "PCI"));
+
+ printk(KERN_INFO PFX
+ "mem IO base address adjusted = 0x%p\n",
+ qdev->mem_map_registers);
+ printk(KERN_INFO PFX "Interrupt number = %d\n", pdev->irq);
+
+ if (netif_msg_probe(qdev))
+ printk(KERN_INFO PFX
+ "%s: MAC address %02x:%02x:%02x:%02x:%02x:%02x\n",
+ ndev->name, ndev->dev_addr[0], ndev->dev_addr[1],
+ ndev->dev_addr[2], ndev->dev_addr[3], ndev->dev_addr[4],
+ ndev->dev_addr[5]);
+}
+
+static int ql_adapter_down(struct ql3_adapter *qdev, int do_reset)
+{
+ struct net_device *ndev = qdev->ndev;
+ int retval = 0;
+
+ netif_stop_queue(ndev);
+ netif_carrier_off(ndev);
+
+ clear_bit(QL_ADAPTER_UP,&qdev->flags);
+ clear_bit(QL_LINK_MASTER,&qdev->flags);
+
+ ql_disable_interrupts(qdev);
+
+ free_irq(qdev->pdev->irq, ndev);
+
+ if (qdev->msi && test_bit(QL_MSI_ENABLED,&qdev->flags)) {
+ printk(KERN_INFO PFX
+ "%s: calling pci_disable_msi().\n", qdev->ndev->name);
+ clear_bit(QL_MSI_ENABLED,&qdev->flags);
+ pci_disable_msi(qdev->pdev);
+ }
+
+ del_timer_sync(&qdev->adapter_timer);
+
+ netif_poll_disable(ndev);
+
+ if (do_reset) {
+ int soft_reset;
+ unsigned long hw_flags;
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ if (ql_wait_for_drvr_lock(qdev)) {
+ if ((soft_reset = ql_adapter_reset(qdev))) {
+ printk(KERN_ERR PFX
+ "%s: ql_adapter_reset(%d) FAILED!\n",
+ ndev->name, qdev->index);
+ }
+ printk(KERN_ERR PFX
+ "%s: Releaseing driver lock via chip reset.\n",ndev->name);
+ } else {
+ printk(KERN_ERR PFX
+ "%s: Could not acquire driver lock to do "
+ "reset!\n", ndev->name);
+ retval = -1;
+ }
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+ }
+ ql_free_mem_resources(qdev);
+ return retval;
+}
+
+static int ql_adapter_up(struct ql3_adapter *qdev)
+{
+ struct net_device *ndev = qdev->ndev;
+ int err;
+ unsigned long irq_flags = SA_SAMPLE_RANDOM | SA_SHIRQ;
+ unsigned long hw_flags;
+
+ if (ql_alloc_mem_resources(qdev)) {
+ printk(KERN_ERR PFX
+ "%s Unable to allocate buffers.\n", ndev->name);
+ return -ENOMEM;
+ }
+
+ if (qdev->msi) {
+ if (pci_enable_msi(qdev->pdev)) {
+ printk(KERN_ERR PFX
+ "%s: User requested MSI, but MSI failed to "
+ "initialize. Continuing without MSI.\n",
+ qdev->ndev->name);
+ qdev->msi = 0;
+ } else {
+ printk(KERN_INFO PFX "%s: MSI Enabled...\n", qdev->ndev->name);
+ set_bit(QL_MSI_ENABLED,&qdev->flags);
+ irq_flags &= ~SA_SHIRQ;
+ }
+ }
+
+ if ((err = request_irq(qdev->pdev->irq,
+ ql3xxx_isr,
+ irq_flags, ndev->name, ndev))) {
+ printk(KERN_ERR PFX
+ "%s: Failed to reserve interrupt %d already in use.\n",
+ ndev->name, qdev->pdev->irq);
+ goto err_irq;
+ }
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+
+ if ((err = ql_wait_for_drvr_lock(qdev))) {
+ if ((err = ql_adapter_initialize(qdev))) {
+ printk(KERN_ERR PFX
+ "%s: Unable to initialize adapter.\n",
+ ndev->name);
+ goto err_init;
+ }
+ printk(KERN_ERR PFX
+ "%s: Releaseing driver lock.\n",ndev->name);
+ ql_sem_unlock(qdev, QL_DRVR_SEM_MASK);
+ } else {
+ printk(KERN_ERR PFX
+ "%s: Could not aquire driver lock.\n",
+ ndev->name);
+ goto err_lock;
+ }
+
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+ set_bit(QL_ADAPTER_UP,&qdev->flags);
+
+ mod_timer(&qdev->adapter_timer, jiffies + HZ * 1);
+
+ netif_poll_enable(ndev);
+ ql_enable_interrupts(qdev);
+ return 0;
+
+err_init:
+ ql_sem_unlock(qdev, QL_DRVR_SEM_MASK);
+err_lock:
+ free_irq(qdev->pdev->irq, ndev);
+err_irq:
+ if (qdev->msi && test_bit(QL_MSI_ENABLED,&qdev->flags)) {
+ printk(KERN_INFO PFX
+ "%s: calling pci_disable_msi().\n",
+ qdev->ndev->name);
+ clear_bit(QL_MSI_ENABLED,&qdev->flags);
+ pci_disable_msi(qdev->pdev);
+ }
+ return err;
+}
+
+static int ql_cycle_adapter(struct ql3_adapter *qdev, int reset)
+{
+ if( ql_adapter_down(qdev,reset) || ql_adapter_up(qdev)) {
+ printk(KERN_ERR PFX
+ "%s: Driver up/down cycle failed, "
+ "closing device\n",qdev->ndev->name);
+ dev_close(qdev->ndev);
+ return -1;
+ }
+ return 0;
+}
+
+static int ql3xxx_close(struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+
+ /*
+ * Wait for device to recover from a reset.
+ * (Rarely happens, but possible.)
+ */
+ while (!test_bit(QL_ADAPTER_UP,&qdev->flags))
+ msleep(50);
+
+ ql_adapter_down(qdev,QL_DO_RESET);
+ return 0;
+}
+
+static int ql3xxx_open(struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ return (ql_adapter_up(qdev));
+}
+
+static struct net_device_stats *ql3xxx_get_stats(struct net_device *dev)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)dev->priv;
+ return &qdev->stats;
+}
+
+static int ql3xxx_change_mtu(struct net_device *ndev, int new_mtu)
+{
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+ printk(KERN_ERR PFX "%s: new mtu size = %d.\n", ndev->name, new_mtu);
+ if (new_mtu != NORMAL_MTU_SIZE && new_mtu != JUMBO_MTU_SIZE) {
+ printk(KERN_ERR PFX
+ "%s: mtu size of %d is not valid. Use exactly %d or "
+ "%d.\n", ndev->name, new_mtu, NORMAL_MTU_SIZE,
+ JUMBO_MTU_SIZE);
+ return -EINVAL;
+ }
+
+ if (!netif_running(ndev)) {
+ ndev->mtu = new_mtu;
+ return 0;
+ }
+
+ ndev->mtu = new_mtu;
+ return ql_cycle_adapter(qdev,QL_DO_RESET);
+}
+
+static void ql3xxx_set_multicast_list(struct net_device *ndev)
+{
+ /*
+ * We are manually parsing the list in the net_device structure.
+ */
+ return;
+}
+
+static int ql3xxx_set_mac_address(struct net_device *ndev, void *p)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)netdev_priv(ndev);
+ struct ql3xxx_port_registers __iomem *port_regs =
+ qdev->mem_map_registers;
+ struct sockaddr *addr = p;
+ unsigned long hw_flags;
+
+ if (netif_running(ndev))
+ return -EBUSY;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+
+ memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);
+
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ /* Program lower 32 bits of the MAC address */
+ ql_write_page0_reg(qdev, &port_regs->macAddrIndirectPtrReg,
+ (MAC_ADDR_INDIRECT_PTR_REG_RP_MASK << 16));
+ ql_write_page0_reg(qdev, &port_regs->macAddrDataReg,
+ ((ndev->dev_addr[2] << 24) | (ndev->
+ dev_addr[3] << 16) |
+ (ndev->dev_addr[4] << 8) | ndev->dev_addr[5]));
+
+ /* Program top 16 bits of the MAC address */
+ ql_write_page0_reg(qdev, &port_regs->macAddrIndirectPtrReg,
+ ((MAC_ADDR_INDIRECT_PTR_REG_RP_MASK << 16) | 1));
+ ql_write_page0_reg(qdev, &port_regs->macAddrDataReg,
+ ((ndev->dev_addr[0] << 8) | ndev->dev_addr[1]));
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+ return 0;
+}
+
+static void ql3xxx_tx_timeout(struct net_device *ndev)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)netdev_priv(ndev);
+
+ printk(KERN_ERR PFX "%s: Resetting...\n", ndev->name);
+ /*
+ * Stop the queues, we've got a problem.
+ */
+ netif_stop_queue(ndev);
+
+ /*
+ * Wake up the worker to process this event.
+ */
+ queue_work(qdev->workqueue, &qdev->tx_timeout_work);
+}
+
+static void ql_reset_work(struct ql3_adapter *qdev)
+{
+ struct net_device *ndev = qdev->ndev;
+ u32 value;
+ struct ql_tx_buf_cb *tx_cb;
+ int max_wait_time, i;
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ unsigned long hw_flags;
+
+ if (test_bit((QL_RESET_PER_SCSI | QL_RESET_START),&qdev->flags)) {
+ clear_bit(QL_LINK_MASTER,&qdev->flags);
+
+ /*
+ * Loop through the active list and return the skb.
+ */
+ for (i = 0; i < NUM_REQ_Q_ENTRIES; i++) {
+ tx_cb = &qdev->tx_buf[i];
+ if (tx_cb->skb) {
+
+ printk(KERN_DEBUG PFX
+ "%s: Freeing lost SKB.\n",
+ qdev->ndev->name);
+ pci_unmap_single(qdev->pdev,
+ pci_unmap_addr(tx_cb, mapaddr),
+ pci_unmap_len(tx_cb, maplen), PCI_DMA_TODEVICE);
+ dev_kfree_skb(tx_cb->skb);
+ tx_cb->skb = NULL;
+ }
+ }
+
+ printk(KERN_ERR PFX
+ "%s: Clearing NRI after reset.\n", qdev->ndev->name);
+ spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+ ql_write_common_reg(qdev,
+ &port_regs->CommonRegs.
+ ispControlStatus,
+ ((ISP_CONTROL_RI << 16) | ISP_CONTROL_RI));
+ /*
+ * Wait the for Soft Reset to Complete.
+ */
+ max_wait_time = 10;
+ do {
+ value = ql_read_common_reg(qdev,
+ &port_regs->CommonRegs.
+
+ ispControlStatus);
+ if ((value & ISP_CONTROL_SR) == 0) {
+ printk(KERN_DEBUG PFX
+ "%s: reset completed.\n",
+ qdev->ndev->name);
+ break;
+ }
+
+ if (value & ISP_CONTROL_RI) {
+ printk(KERN_DEBUG PFX
+ "%s: clearing NRI after reset.\n",
+ qdev->ndev->name);
+ ql_write_common_reg(qdev,
+ (u32 *) &
+ port_regs->
+ CommonRegs.
+ ispControlStatus,
+ ((ISP_CONTROL_RI <<
+ 16) | ISP_CONTROL_RI));
+ }
+
+ ssleep(1);
+ } while (--max_wait_time);
+ spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+ if (value & ISP_CONTROL_SR) {
+
+ /*
+ * Set the reset flags and clear the board again.
+ * Nothing else to do...
+ */
+ printk(KERN_ERR PFX
+ "%s: Timed out waiting for reset to "
+ "complete.\n", ndev->name);
+ printk(KERN_ERR PFX
+ "%s: Do a reset.\n", ndev->name);
+ clear_bit(QL_RESET_PER_SCSI,&qdev->flags);
+ clear_bit(QL_RESET_START,&qdev->flags);
+ ql_cycle_adapter(qdev,QL_DO_RESET);
+ return;
+ }
+
+ clear_bit(QL_RESET_ACTIVE,&qdev->flags);
+ clear_bit(QL_RESET_PER_SCSI,&qdev->flags);
+ clear_bit(QL_RESET_START,&qdev->flags);
+ ql_cycle_adapter(qdev,QL_NO_RESET);
+ }
+}
+
+static void ql_tx_timeout_work(struct ql3_adapter *qdev)
+{
+ ql_cycle_adapter(qdev,QL_DO_RESET);
+}
+
+static void ql_get_board_info(struct ql3_adapter *qdev)
+{
+ struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
+ u32 value;
+
+ value = ql_read_page0_reg_l(qdev, &port_regs->portStatus);
+
+ qdev->chip_rev_id = ((value & PORT_STATUS_REV_ID_MASK) >> 12);
+ if (value & PORT_STATUS_64)
+ qdev->pci_width = 64;
+ else
+ qdev->pci_width = 32;
+ if (value & PORT_STATUS_X)
+ qdev->pci_x = 1;
+ else
+ qdev->pci_x = 0;
+ qdev->pci_slot = (u8) PCI_SLOT(qdev->pdev->devfn);
+}
+
+static void ql3xxx_timer(unsigned long ptr)
+{
+ struct ql3_adapter *qdev = (struct ql3_adapter *)ptr;
+
+ if (test_bit(QL_RESET_ACTIVE,&qdev->flags)) {
+ printk(KERN_DEBUG PFX
+ "%s: Reset in progress.\n",
+ qdev->ndev->name);
+ goto end;
+ }
+
+ ql_link_state_machine(qdev);
+
+ /* Restart timer on 2 second interval. */
+end:
+ mod_timer(&qdev->adapter_timer, jiffies + HZ * 1);
+}
+
+static int __devinit ql3xxx_probe(struct pci_dev *pdev,
+ const struct pci_device_id *pci_entry)
+{
+ struct net_device *ndev = NULL;
+ struct ql3_adapter *qdev = NULL;
+ static int cards_found = 0;
+ int pci_using_dac, err;
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ printk(KERN_ERR PFX "%s cannot enable PCI device\n",
+ pci_name(pdev));
+ goto err_out;
+ }
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err) {
+ printk(KERN_ERR PFX "%s cannot obtain PCI resources\n",
+ pci_name(pdev));
+ goto err_out_disable_pdev;
+ }
+
+ pci_set_master(pdev);
+
+ if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
+ pci_using_dac = 1;
+ err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
+ } else if (!(err = pci_set_dma_mask(pdev, DMA_32BIT_MASK))) {
+ pci_using_dac = 0;
+ err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ }
+
+ if (err) {
+ printk(KERN_ERR PFX "%s no usable DMA configuration\n",
+ pci_name(pdev));
+ goto err_out_free_regions;
+ }
+
+ ndev = alloc_etherdev(sizeof(struct ql3_adapter));
+ if (!ndev)
+ goto err_out_free_regions;
+
+ SET_MODULE_OWNER(ndev);
+ SET_NETDEV_DEV(ndev, &pdev->dev);
+
+ ndev->features = NETIF_F_LLTX;
+ if (pci_using_dac)
+ ndev->features |= NETIF_F_HIGHDMA;
+
+ pci_set_drvdata(pdev, ndev);
+
+ qdev = netdev_priv(ndev);
+ qdev->index = cards_found;
+ qdev->ndev = ndev;
+ qdev->pdev = pdev;
+ qdev->port_link_state = LS_DOWN;
+ if (msi)
+ qdev->msi = 1;
+
+ qdev->msg_enable = netif_msg_init(debug, default_msg);
+
+ qdev->mem_map_registers =
+ ioremap_nocache(pci_resource_start(pdev, 1),
+ pci_resource_len(qdev->pdev, 1));
+ if (!qdev->mem_map_registers) {
+ printk(KERN_ERR PFX "%s: cannot map device registers\n",
+ pci_name(pdev));
+ goto err_out_free_ndev;
+ }
+
+ spin_lock_init(&qdev->adapter_lock);
+ spin_lock_init(&qdev->hw_lock);
+
+ /* Set driver entry points */
+ ndev->open = ql3xxx_open;
+ ndev->hard_start_xmit = ql3xxx_send;
+ ndev->stop = ql3xxx_close;
+ ndev->get_stats = ql3xxx_get_stats;
+ ndev->change_mtu = ql3xxx_change_mtu;
+ ndev->set_multicast_list = ql3xxx_set_multicast_list;
+ SET_ETHTOOL_OPS(ndev, &ql3xxx_ethtool_ops);
+ ndev->set_mac_address = ql3xxx_set_mac_address;
+ ndev->tx_timeout = ql3xxx_tx_timeout;
+ ndev->watchdog_timeo = 5 * HZ;
+
+ ndev->poll = &ql_poll;
+ ndev->weight = 64;
+
+ ndev->irq = pdev->irq;
+
+ /* make sure the EEPROM is good */
+ if (ql_get_nvram_params(qdev)) {
+ printk(KERN_ALERT PFX
+ "ql3xxx_probe: Adapter #%d, Invalid NVRAM parameters.\n",
+ qdev->index);
+ goto err_out_iounmap;
+ }
+
+ ql_set_mac_info(qdev);
+
+ /* Validate and set parameters */
+ if (qdev->mac_index) {
+ memcpy(ndev->dev_addr, &qdev->nvram_data.funcCfg_fn2.macAddress,
+ ETH_ALEN);
+ } else {
+ memcpy(ndev->dev_addr, &qdev->nvram_data.funcCfg_fn0.macAddress,
+ ETH_ALEN);
+ }
+ memcpy(ndev->perm_addr, ndev->dev_addr, ndev->addr_len);
+
+ ndev->tx_queue_len = NUM_REQ_Q_ENTRIES;
+
+ /* Turn off support for multicasting */
+ ndev->flags &= ~IFF_MULTICAST;
+
+ /* Record PCI bus information. */
+ ql_get_board_info(qdev);
+
+ /*
+ * Set the Maximum Memory Read Byte Count value. We do this to handle
+ * jumbo frames.
+ */
+ if (qdev->pci_x) {
+ pci_write_config_word(pdev, (int)0x4e, (u16) 0x0036);
+ }
+
+ err = register_netdev(ndev);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot register net device\n",
+ pci_name(pdev));
+ goto err_out_iounmap;
+ }
+
+ /* we're going to reset, so assume we have no link for now */
+
+ netif_carrier_off(ndev);
+ netif_stop_queue(ndev);
+
+ qdev->workqueue = create_singlethread_workqueue(ndev->name);
+ INIT_WORK(&qdev->reset_work, (void (*)(void *))ql_reset_work, qdev);
+ INIT_WORK(&qdev->tx_timeout_work,
+ (void (*)(void *))ql_tx_timeout_work, qdev);
+
+ init_timer(&qdev->adapter_timer);
+ qdev->adapter_timer.function = ql3xxx_timer;
+ qdev->adapter_timer.expires = jiffies + HZ * 2; /* two second delay */
+ qdev->adapter_timer.data = (unsigned long)qdev;
+
+ if(!cards_found) {
+ printk(KERN_ALERT PFX "%s\n", DRV_STRING);
+ printk(KERN_ALERT PFX "Driver name: %s, Version: %s.\n",
+ DRV_NAME, DRV_VERSION);
+ }
+ ql_display_dev_info(ndev);
+
+ cards_found++;
+ return 0;
+
+err_out_iounmap:
+ iounmap(qdev->mem_map_registers);
+err_out_free_ndev:
+ free_netdev(ndev);
+err_out_free_regions:
+ pci_release_regions(pdev);
+err_out_disable_pdev:
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+err_out:
+ return err;
+}
+
+static void __devexit ql3xxx_remove(struct pci_dev *pdev)
+{
+ struct net_device *ndev = pci_get_drvdata(pdev);
+ struct ql3_adapter *qdev = netdev_priv(ndev);
+
+ unregister_netdev(ndev);
+ qdev = netdev_priv(ndev);
+
+ ql_disable_interrupts(qdev);
+
+ if (qdev->workqueue) {
+ cancel_delayed_work(&qdev->reset_work);
+ cancel_delayed_work(&qdev->tx_timeout_work);
+ destroy_workqueue(qdev->workqueue);
+ qdev->workqueue = NULL;
+ }
+
+ iounmap((void *)qdev->mmap_virt_base);
+ pci_release_regions(pdev);
+ pci_set_drvdata(pdev, NULL);
+ free_netdev(ndev);
+}
+
+static struct pci_driver ql3xxx_driver = {
+
+ .name = DRV_NAME,
+ .id_table = ql3xxx_pci_tbl,
+ .probe = ql3xxx_probe,
+ .remove = __devexit_p(ql3xxx_remove),
+};
+
+static int __init ql3xxx_init_module(void)
+{
+ return pci_register_driver(&ql3xxx_driver);
+}
+
+static void __exit ql3xxx_exit(void)
+{
+ pci_unregister_driver(&ql3xxx_driver);
+}
+
+module_init(ql3xxx_init_module);
+module_exit(ql3xxx_exit);
diff --git a/drivers/net/qla3xxx.h b/drivers/net/qla3xxx.h
new file mode 100644
index 0000000..9492cee
--- /dev/null
+++ b/drivers/net/qla3xxx.h
@@ -0,0 +1,1194 @@
+/*
+ * QLogic QLA3xxx NIC HBA Driver
+ * Copyright (c) 2003-2006 QLogic Corporation
+ *
+ * See LICENSE.qla3xxx for copyright and licensing details.
+ */
+#ifndef _QLA3XXX_H_
+#define _QLA3XXX_H_
+
+/*
+ * IOCB Definitions...
+ */
+#pragma pack(1)
+
+#define OPCODE_OB_MAC_IOCB_FN0 0x01
+#define OPCODE_OB_MAC_IOCB_FN2 0x21
+#define OPCODE_OB_TCP_IOCB_FN0 0x03
+#define OPCODE_OB_TCP_IOCB_FN2 0x23
+#define OPCODE_UPDATE_NCB_IOCB_FN0 0x00
+#define OPCODE_UPDATE_NCB_IOCB_FN2 0x20
+
+#define OPCODE_UPDATE_NCB_IOCB 0xF0
+#define OPCODE_IB_MAC_IOCB 0xF9
+#define OPCODE_IB_IP_IOCB 0xFA
+#define OPCODE_IB_TCP_IOCB 0xFB
+#define OPCODE_DUMP_PROTO_IOCB 0xFE
+#define OPCODE_BUFFER_ALERT_IOCB 0xFB
+
+#define OPCODE_FUNC_ID_MASK 0x30
+#define OUTBOUND_MAC_IOCB 0x01 /* plus function bits */
+#define OUTBOUND_TCP_IOCB 0x03 /* plus function bits */
+#define UPDATE_NCB_IOCB 0x00 /* plus function bits */
+
+#define FN0_MA_BITS_MASK 0x00
+#define FN1_MA_BITS_MASK 0x80
+
+struct ob_mac_iocb_req {
+ u8 opcode;
+ u8 flags;
+#define OB_MAC_IOCB_REQ_MA 0xC0
+#define OB_MAC_IOCB_REQ_F 0x20
+#define OB_MAC_IOCB_REQ_X 0x10
+#define OB_MAC_IOCB_REQ_D 0x02
+#define OB_MAC_IOCB_REQ_I 0x01
+ __le16 reserved0;
+
+ __le32 transaction_id;
+ __le16 data_len;
+ __le16 reserved1;
+ __le32 reserved2;
+ __le32 reserved3;
+ __le32 buf_addr0_low;
+ __le32 buf_addr0_high;
+ __le32 buf_0_len;
+ __le32 buf_addr1_low;
+ __le32 buf_addr1_high;
+ __le32 buf_1_len;
+ __le32 buf_addr2_low;
+ __le32 buf_addr2_high;
+ __le32 buf_2_len;
+ __le32 reserved4;
+ __le32 reserved5;
+};
+/*
+ * The following constants define control bits for buffer
+ * length fields for all IOCB's.
+ */
+#define OB_MAC_IOCB_REQ_E 0x80000000 /* Last valid buffer in list. */
+#define OB_MAC_IOCB_REQ_C 0x40000000 /* points to an OAL. (continuation) */
+#define OB_MAC_IOCB_REQ_L 0x20000000 /* Auburn local address pointer. */
+#define OB_MAC_IOCB_REQ_R 0x10000000 /* 32-bit address pointer. */
+
+struct ob_mac_iocb_rsp {
+ u8 opcode;
+ u8 flags;
+#define OB_MAC_IOCB_RSP_P 0x08
+#define OB_MAC_IOCB_RSP_S 0x02
+#define OB_MAC_IOCB_RSP_I 0x01
+
+ __le16 reserved0;
+ __le32 transaction_id;
+ __le32 reserved1;
+ __le32 reserved2;
+};
+
+struct ib_mac_iocb_rsp {
+ u8 opcode;
+ u8 flags;
+#define IB_MAC_IOCB_RSP_S 0x80
+#define IB_MAC_IOCB_RSP_H1 0x40
+#define IB_MAC_IOCB_RSP_H0 0x20
+#define IB_MAC_IOCB_RSP_B 0x10
+#define IB_MAC_IOCB_RSP_M 0x08
+#define IB_MAC_IOCB_RSP_MA 0x07
+
+ __le16 length;
+ __le32 reserved;
+ __le32 ial_low;
+ __le32 ial_high;
+
+};
+
+struct ob_ip_iocb_req {
+ u8 opcode;
+ __le16 flags;
+#define OB_IP_IOCB_REQ_O 0x100
+#define OB_IP_IOCB_REQ_H 0x008
+#define OB_IP_IOCB_REQ_U 0x004
+#define OB_IP_IOCB_REQ_D 0x002
+#define OB_IP_IOCB_REQ_I 0x001
+
+ u8 reserved0;
+
+ __le32 transaction_id;
+ __le16 data_len;
+ __le16 reserved1;
+ __le32 hncb_ptr_low;
+ __le32 hncb_ptr_high;
+ __le32 buf_addr0_low;
+ __le32 buf_addr0_high;
+ __le32 buf_0_len;
+ __le32 buf_addr1_low;
+ __le32 buf_addr1_high;
+ __le32 buf_1_len;
+ __le32 buf_addr2_low;
+ __le32 buf_addr2_high;
+ __le32 buf_2_len;
+ __le32 reserved2;
+ __le32 reserved3;
+};
+
+/* defines for BufferLength fields above */
+#define OB_IP_IOCB_REQ_E 0x80000000
+#define OB_IP_IOCB_REQ_C 0x40000000
+#define OB_IP_IOCB_REQ_L 0x20000000
+#define OB_IP_IOCB_REQ_R 0x10000000
+
+struct ob_ip_iocb_rsp {
+ u8 opcode;
+ u8 flags;
+#define OB_MAC_IOCB_RSP_E 0x08
+#define OB_MAC_IOCB_RSP_L 0x04
+#define OB_MAC_IOCB_RSP_S 0x02
+#define OB_MAC_IOCB_RSP_I 0x01
+
+ __le16 reserved0;
+ __le32 transaction_id;
+ __le32 reserved1;
+ __le32 reserved2;
+};
+
+struct ob_tcp_iocb_req {
+ u8 opcode;
+
+ u8 flags0;
+#define OB_TCP_IOCB_REQ_P 0x80
+#define OB_TCP_IOCB_REQ_CI 0x20
+#define OB_TCP_IOCB_REQ_H 0x10
+#define OB_TCP_IOCB_REQ_LN 0x08
+#define OB_TCP_IOCB_REQ_K 0x04
+#define OB_TCP_IOCB_REQ_D 0x02
+#define OB_TCP_IOCB_REQ_I 0x01
+
+ u8 flags1;
+#define OB_TCP_IOCB_REQ_OSM 0x40
+#define OB_TCP_IOCB_REQ_URG 0x20
+#define OB_TCP_IOCB_REQ_ACK 0x10
+#define OB_TCP_IOCB_REQ_PSH 0x08
+#define OB_TCP_IOCB_REQ_RST 0x04
+#define OB_TCP_IOCB_REQ_SYN 0x02
+#define OB_TCP_IOCB_REQ_FIN 0x01
+
+ u8 options_len;
+#define OB_TCP_IOCB_REQ_OMASK 0xF0
+#define OB_TCP_IOCB_REQ_SHIFT 4
+
+ __le32 transaction_id;
+ __le32 data_len;
+ __le32 hncb_ptr_low;
+ __le32 hncb_ptr_high;
+ __le32 buf_addr0_low;
+ __le32 buf_addr0_high;
+ __le32 buf_0_len;
+ __le32 buf_addr1_low;
+ __le32 buf_addr1_high;
+ __le32 buf_1_len;
+ __le32 buf_addr2_low;
+ __le32 buf_addr2_high;
+ __le32 buf_2_len;
+ __le32 time_stamp;
+ __le32 reserved1;
+};
+
+struct ob_tcp_iocb_rsp {
+ u8 opcode;
+
+ u8 flags0;
+#define OB_TCP_IOCB_RSP_C 0x20
+#define OB_TCP_IOCB_RSP_H 0x10
+#define OB_TCP_IOCB_RSP_LN 0x08
+#define OB_TCP_IOCB_RSP_K 0x04
+#define OB_TCP_IOCB_RSP_D 0x02
+#define OB_TCP_IOCB_RSP_I 0x01
+
+ u8 flags1;
+#define OB_TCP_IOCB_RSP_E 0x10
+#define OB_TCP_IOCB_RSP_W 0x08
+#define OB_TCP_IOCB_RSP_P 0x04
+#define OB_TCP_IOCB_RSP_T 0x02
+#define OB_TCP_IOCB_RSP_F 0x01
+
+ u8 state;
+#define OB_TCP_IOCB_RSP_SMASK 0xF0
+#define OB_TCP_IOCB_RSP_SHIFT 4
+
+ __le32 transaction_id;
+ __le32 local_ncb_ptr;
+ __le32 reserved0;
+};
+
+struct ib_ip_iocb_rsp {
+ u8 opcode;
+ u8 flags;
+#define IB_IP_IOCB_RSP_S 0x80
+#define IB_IP_IOCB_RSP_H1 0x40
+#define IB_IP_IOCB_RSP_H0 0x20
+#define IB_IP_IOCB_RSP_B 0x10
+#define IB_IP_IOCB_RSP_M 0x08
+#define IB_IP_IOCB_RSP_MA 0x07
+
+ __le16 length;
+ __le16 checksum;
+ __le16 reserved;
+#define IB_IP_IOCB_RSP_R 0x01
+ __le32 ial_low;
+ __le32 ial_high;
+};
+
+struct ib_tcp_iocb_rsp {
+ u8 opcode;
+ u8 flags;
+#define IB_TCP_IOCB_RSP_P 0x80
+#define IB_TCP_IOCB_RSP_T 0x40
+#define IB_TCP_IOCB_RSP_D 0x20
+#define IB_TCP_IOCB_RSP_N 0x10
+#define IB_TCP_IOCB_RSP_IP 0x03
+#define IB_TCP_FLAG_MASK 0xf0
+#define IB_TCP_FLAG_IOCB_SYN 0x00
+
+#define TCP_IB_RSP_FLAGS(x) (x->flags & ~IB_TCP_FLAG_MASK)
+
+ __le16 length;
+ __le32 hncb_ref_num;
+ __le32 ial_low;
+ __le32 ial_high;
+};
+
+struct net_rsp_iocb {
+ u8 opcode;
+ u8 flags;
+ __le16 reserved0;
+ __le32 reserved[3];
+};
+#pragma pack()
+
+/*
+ * Register Definitions...
+ */
+#define PORT0_PHY_ADDRESS 0x1e00
+#define PORT1_PHY_ADDRESS 0x1f00
+
+#define ETHERNET_CRC_SIZE 4
+
+#define MII_SCAN_REGISTER 0x00000001
+
+/* 32-bit ispControlStatus */
+enum {
+ ISP_CONTROL_NP_MASK = 0x0003,
+ ISP_CONTROL_NP_PCSR = 0x0000,
+ ISP_CONTROL_NP_HMCR = 0x0001,
+ ISP_CONTROL_NP_LRAMCR = 0x0002,
+ ISP_CONTROL_NP_PSR = 0x0003,
+ ISP_CONTROL_RI = 0x0008,
+ ISP_CONTROL_CI = 0x0010,
+ ISP_CONTROL_PI = 0x0020,
+ ISP_CONTROL_IN = 0x0040,
+ ISP_CONTROL_BE = 0x0080,
+ ISP_CONTROL_FN_MASK = 0x0700,
+ ISP_CONTROL_FN0_NET = 0x0400,
+ ISP_CONTROL_FN0_SCSI = 0x0500,
+ ISP_CONTROL_FN1_NET = 0x0600,
+ ISP_CONTROL_FN1_SCSI = 0x0700,
+ ISP_CONTROL_LINK_DN_0 = 0x0800,
+ ISP_CONTROL_LINK_DN_1 = 0x1000,
+ ISP_CONTROL_FSR = 0x2000,
+ ISP_CONTROL_FE = 0x4000,
+ ISP_CONTROL_SR = 0x8000,
+};
+
+/* 32-bit ispInterruptMaskReg */
+enum {
+ ISP_IMR_ENABLE_INT = 0x0004,
+ ISP_IMR_DISABLE_RESET_INT = 0x0008,
+ ISP_IMR_DISABLE_CMPL_INT = 0x0010,
+ ISP_IMR_DISABLE_PROC_INT = 0x0020,
+};
+
+/* 32-bit serialPortInterfaceReg */
+enum {
+ ISP_SERIAL_PORT_IF_CLK = 0x0001,
+ ISP_SERIAL_PORT_IF_CS = 0x0002,
+ ISP_SERIAL_PORT_IF_D0 = 0x0004,
+ ISP_SERIAL_PORT_IF_DI = 0x0008,
+ ISP_NVRAM_MASK = (0x000F << 16),
+ ISP_SERIAL_PORT_IF_WE = 0x0010,
+ ISP_SERIAL_PORT_IF_NVR_MASK = 0x001F,
+ ISP_SERIAL_PORT_IF_SCI = 0x0400,
+ ISP_SERIAL_PORT_IF_SC0 = 0x0800,
+ ISP_SERIAL_PORT_IF_SCE = 0x1000,
+ ISP_SERIAL_PORT_IF_SDI = 0x2000,
+ ISP_SERIAL_PORT_IF_SDO = 0x4000,
+ ISP_SERIAL_PORT_IF_SDE = 0x8000,
+ ISP_SERIAL_PORT_IF_I2C_MASK = 0xFC00,
+};
+
+/* semaphoreReg */
+enum {
+ QL_RESOURCE_MASK_BASE_CODE = 0x7,
+ QL_RESOURCE_BITS_BASE_CODE = 0x4,
+ QL_DRVR_SEM_BITS = (QL_RESOURCE_BITS_BASE_CODE << 1),
+ QL_DDR_RAM_SEM_BITS = (QL_RESOURCE_BITS_BASE_CODE << 4),
+ QL_PHY_GIO_SEM_BITS = (QL_RESOURCE_BITS_BASE_CODE << 7),
+ QL_NVRAM_SEM_BITS = (QL_RESOURCE_BITS_BASE_CODE << 10),
+ QL_FLASH_SEM_BITS = (QL_RESOURCE_BITS_BASE_CODE << 13),
+ QL_DRVR_SEM_MASK = (QL_RESOURCE_MASK_BASE_CODE << (1 + 16)),
+ QL_DDR_RAM_SEM_MASK = (QL_RESOURCE_MASK_BASE_CODE << (4 + 16)),
+ QL_PHY_GIO_SEM_MASK = (QL_RESOURCE_MASK_BASE_CODE << (7 + 16)),
+ QL_NVRAM_SEM_MASK = (QL_RESOURCE_MASK_BASE_CODE << (10 + 16)),
+ QL_FLASH_SEM_MASK = (QL_RESOURCE_MASK_BASE_CODE << (13 + 16)),
+};
+
+ /*
+ * QL3XXX memory-mapped registers
+ * QL3XXX has 4 "pages" of registers, each page occupying
+ * 256 bytes. Each page has a "common" area at the start and then
+ * page-specific registers after that.
+ */
+struct ql3xxx_common_registers {
+ u32 MB0; /* Offset 0x00 */
+ u32 MB1; /* Offset 0x04 */
+ u32 MB2; /* Offset 0x08 */
+ u32 MB3; /* Offset 0x0c */
+ u32 MB4; /* Offset 0x10 */
+ u32 MB5; /* Offset 0x14 */
+ u32 MB6; /* Offset 0x18 */
+ u32 MB7; /* Offset 0x1c */
+ u32 flashBiosAddr;
+ u32 flashBiosData;
+ u32 ispControlStatus;
+ u32 ispInterruptMaskReg;
+ u32 serialPortInterfaceReg;
+ u32 semaphoreReg;
+ u32 reqQProducerIndex;
+ u32 rspQConsumerIndex;
+
+ u32 rxLargeQProducerIndex;
+ u32 rxSmallQProducerIndex;
+ u32 arcMadiCommand;
+ u32 arcMadiData;
+};
+
+enum {
+ EXT_HW_CONFIG_SP_MASK = 0x0006,
+ EXT_HW_CONFIG_SP_NONE = 0x0000,
+ EXT_HW_CONFIG_SP_BYTE_PARITY = 0x0002,
+ EXT_HW_CONFIG_SP_ECC = 0x0004,
+ EXT_HW_CONFIG_SP_ECCx = 0x0006,
+ EXT_HW_CONFIG_SIZE_MASK = 0x0060,
+ EXT_HW_CONFIG_SIZE_128M = 0x0000,
+ EXT_HW_CONFIG_SIZE_256M = 0x0020,
+ EXT_HW_CONFIG_SIZE_512M = 0x0040,
+ EXT_HW_CONFIG_SIZE_INVALID = 0x0060,
+ EXT_HW_CONFIG_PD = 0x0080,
+ EXT_HW_CONFIG_FW = 0x0200,
+ EXT_HW_CONFIG_US = 0x0400,
+ EXT_HW_CONFIG_DCS_MASK = 0x1800,
+ EXT_HW_CONFIG_DCS_9MA = 0x0000,
+ EXT_HW_CONFIG_DCS_15MA = 0x0800,
+ EXT_HW_CONFIG_DCS_18MA = 0x1000,
+ EXT_HW_CONFIG_DCS_24MA = 0x1800,
+ EXT_HW_CONFIG_DDS_MASK = 0x6000,
+ EXT_HW_CONFIG_DDS_9MA = 0x0000,
+ EXT_HW_CONFIG_DDS_15MA = 0x2000,
+ EXT_HW_CONFIG_DDS_18MA = 0x4000,
+ EXT_HW_CONFIG_DDS_24MA = 0x6000,
+};
+
+/* InternalChipConfig */
+enum {
+ INTERNAL_CHIP_DM = 0x0001,
+ INTERNAL_CHIP_SD = 0x0002,
+ INTERNAL_CHIP_RAP_MASK = 0x000C,
+ INTERNAL_CHIP_RAP_RR = 0x0000,
+ INTERNAL_CHIP_RAP_NRM = 0x0004,
+ INTERNAL_CHIP_RAP_ERM = 0x0008,
+ INTERNAL_CHIP_RAP_ERMx = 0x000C,
+ INTERNAL_CHIP_WE = 0x0010,
+ INTERNAL_CHIP_EF = 0x0020,
+ INTERNAL_CHIP_FR = 0x0040,
+ INTERNAL_CHIP_FW = 0x0080,
+ INTERNAL_CHIP_FI = 0x0100,
+ INTERNAL_CHIP_FT = 0x0200,
+};
+
+/* portControl */
+enum {
+ PORT_CONTROL_DS = 0x0001,
+ PORT_CONTROL_HH = 0x0002,
+ PORT_CONTROL_EI = 0x0004,
+ PORT_CONTROL_ET = 0x0008,
+ PORT_CONTROL_EF = 0x0010,
+ PORT_CONTROL_DRM = 0x0020,
+ PORT_CONTROL_RLB = 0x0040,
+ PORT_CONTROL_RCB = 0x0080,
+ PORT_CONTROL_MAC = 0x0100,
+ PORT_CONTROL_IPV = 0x0200,
+ PORT_CONTROL_IFP = 0x0400,
+ PORT_CONTROL_ITP = 0x0800,
+ PORT_CONTROL_FI = 0x1000,
+ PORT_CONTROL_DFP = 0x2000,
+ PORT_CONTROL_OI = 0x4000,
+ PORT_CONTROL_CC = 0x8000,
+};
+
+/* portStatus */
+enum {
+ PORT_STATUS_SM0 = 0x0001,
+ PORT_STATUS_SM1 = 0x0002,
+ PORT_STATUS_X = 0x0008,
+ PORT_STATUS_DL = 0x0080,
+ PORT_STATUS_IC = 0x0200,
+ PORT_STATUS_MRC = 0x0400,
+ PORT_STATUS_NL = 0x0800,
+ PORT_STATUS_REV_ID_MASK = 0x7000,
+ PORT_STATUS_REV_ID_1 = 0x1000,
+ PORT_STATUS_REV_ID_2 = 0x2000,
+ PORT_STATUS_REV_ID_3 = 0x3000,
+ PORT_STATUS_64 = 0x8000,
+ PORT_STATUS_UP0 = 0x10000,
+ PORT_STATUS_AC0 = 0x20000,
+ PORT_STATUS_AE0 = 0x40000,
+ PORT_STATUS_UP1 = 0x100000,
+ PORT_STATUS_AC1 = 0x200000,
+ PORT_STATUS_AE1 = 0x400000,
+ PORT_STATUS_F0_ENABLED = 0x1000000,
+ PORT_STATUS_F1_ENABLED = 0x2000000,
+ PORT_STATUS_F2_ENABLED = 0x4000000,
+ PORT_STATUS_F3_ENABLED = 0x8000000,
+};
+
+/* macMIIMgmtControlReg */
+enum {
+ MAC_ADDR_INDIRECT_PTR_REG_RP_MASK = 0x0003,
+ MAC_ADDR_INDIRECT_PTR_REG_RP_PRI_LWR = 0x0000,
+ MAC_ADDR_INDIRECT_PTR_REG_RP_PRI_UPR = 0x0001,
+ MAC_ADDR_INDIRECT_PTR_REG_RP_SEC_LWR = 0x0002,
+ MAC_ADDR_INDIRECT_PTR_REG_RP_SEC_UPR = 0x0003,
+ MAC_ADDR_INDIRECT_PTR_REG_PR = 0x0008,
+ MAC_ADDR_INDIRECT_PTR_REG_SS = 0x0010,
+ MAC_ADDR_INDIRECT_PTR_REG_SE = 0x0020,
+ MAC_ADDR_INDIRECT_PTR_REG_SP = 0x0040,
+ MAC_ADDR_INDIRECT_PTR_REG_PE = 0x0080,
+};
+
+/* macMIIMgmtControlReg */
+enum {
+ MAC_MII_CONTROL_RC = 0x0001,
+ MAC_MII_CONTROL_SC = 0x0002,
+ MAC_MII_CONTROL_AS = 0x0004,
+ MAC_MII_CONTROL_NP = 0x0008,
+ MAC_MII_CONTROL_CLK_SEL_MASK = 0x0070,
+ MAC_MII_CONTROL_CLK_SEL_DIV2 = 0x0000,
+ MAC_MII_CONTROL_CLK_SEL_DIV4 = 0x0010,
+ MAC_MII_CONTROL_CLK_SEL_DIV6 = 0x0020,
+ MAC_MII_CONTROL_CLK_SEL_DIV8 = 0x0030,
+ MAC_MII_CONTROL_CLK_SEL_DIV10 = 0x0040,
+ MAC_MII_CONTROL_CLK_SEL_DIV14 = 0x0050,
+ MAC_MII_CONTROL_CLK_SEL_DIV20 = 0x0060,
+ MAC_MII_CONTROL_CLK_SEL_DIV28 = 0x0070,
+ MAC_MII_CONTROL_RM = 0x8000,
+};
+
+/* macMIIStatusReg */
+enum {
+ MAC_MII_STATUS_BSY = 0x0001,
+ MAC_MII_STATUS_SC = 0x0002,
+ MAC_MII_STATUS_NV = 0x0004,
+};
+
+enum {
+ MAC_CONFIG_REG_PE = 0x0001,
+ MAC_CONFIG_REG_TF = 0x0002,
+ MAC_CONFIG_REG_RF = 0x0004,
+ MAC_CONFIG_REG_FD = 0x0008,
+ MAC_CONFIG_REG_GM = 0x0010,
+ MAC_CONFIG_REG_LB = 0x0020,
+ MAC_CONFIG_REG_SR = 0x8000,
+};
+
+enum {
+ MAC_HALF_DUPLEX_REG_ED = 0x10000,
+ MAC_HALF_DUPLEX_REG_NB = 0x20000,
+ MAC_HALF_DUPLEX_REG_BNB = 0x40000,
+ MAC_HALF_DUPLEX_REG_ALT = 0x80000,
+};
+
+enum {
+ IP_ADDR_INDEX_REG_MASK = 0x000f,
+ IP_ADDR_INDEX_REG_FUNC_0_PRI = 0x0000,
+ IP_ADDR_INDEX_REG_FUNC_0_SEC = 0x0001,
+ IP_ADDR_INDEX_REG_FUNC_1_PRI = 0x0002,
+ IP_ADDR_INDEX_REG_FUNC_1_SEC = 0x0003,
+ IP_ADDR_INDEX_REG_FUNC_2_PRI = 0x0004,
+ IP_ADDR_INDEX_REG_FUNC_2_SEC = 0x0005,
+ IP_ADDR_INDEX_REG_FUNC_3_PRI = 0x0006,
+ IP_ADDR_INDEX_REG_FUNC_3_SEC = 0x0007,
+};
+
+enum {
+ PROBE_MUX_ADDR_REG_MUX_SEL_MASK = 0x003f,
+ PROBE_MUX_ADDR_REG_SYSCLK = 0x0000,
+ PROBE_MUX_ADDR_REG_PCICLK = 0x0040,
+ PROBE_MUX_ADDR_REG_NRXCLK = 0x0080,
+ PROBE_MUX_ADDR_REG_CPUCLK = 0x00C0,
+ PROBE_MUX_ADDR_REG_MODULE_SEL_MASK = 0x3f00,
+ PROBE_MUX_ADDR_REG_UP = 0x4000,
+ PROBE_MUX_ADDR_REG_RE = 0x8000,
+};
+
+enum {
+ STATISTICS_INDEX_REG_MASK = 0x01ff,
+ STATISTICS_INDEX_REG_MAC0_TX_FRAME = 0x0000,
+ STATISTICS_INDEX_REG_MAC0_TX_BYTES = 0x0001,
+ STATISTICS_INDEX_REG_MAC0_TX_STAT1 = 0x0002,
+ STATISTICS_INDEX_REG_MAC0_TX_STAT2 = 0x0003,
+ STATISTICS_INDEX_REG_MAC0_TX_STAT3 = 0x0004,
+ STATISTICS_INDEX_REG_MAC0_TX_STAT4 = 0x0005,
+ STATISTICS_INDEX_REG_MAC0_TX_STAT5 = 0x0006,
+ STATISTICS_INDEX_REG_MAC0_RX_FRAME = 0x0007,
+ STATISTICS_INDEX_REG_MAC0_RX_BYTES = 0x0008,
+ STATISTICS_INDEX_REG_MAC0_RX_STAT1 = 0x0009,
+ STATISTICS_INDEX_REG_MAC0_RX_STAT2 = 0x000a,
+ STATISTICS_INDEX_REG_MAC0_RX_STAT3 = 0x000b,
+ STATISTICS_INDEX_REG_MAC0_RX_ERR_CRC = 0x000c,
+ STATISTICS_INDEX_REG_MAC0_RX_ERR_ENC = 0x000d,
+ STATISTICS_INDEX_REG_MAC0_RX_ERR_LEN = 0x000e,
+ STATISTICS_INDEX_REG_MAC0_RX_STAT4 = 0x000f,
+ STATISTICS_INDEX_REG_MAC1_TX_FRAME = 0x0010,
+ STATISTICS_INDEX_REG_MAC1_TX_BYTES = 0x0011,
+ STATISTICS_INDEX_REG_MAC1_TX_STAT1 = 0x0012,
+ STATISTICS_INDEX_REG_MAC1_TX_STAT2 = 0x0013,
+ STATISTICS_INDEX_REG_MAC1_TX_STAT3 = 0x0014,
+ STATISTICS_INDEX_REG_MAC1_TX_STAT4 = 0x0015,
+ STATISTICS_INDEX_REG_MAC1_TX_STAT5 = 0x0016,
+ STATISTICS_INDEX_REG_MAC1_RX_FRAME = 0x0017,
+ STATISTICS_INDEX_REG_MAC1_RX_BYTES = 0x0018,
+ STATISTICS_INDEX_REG_MAC1_RX_STAT1 = 0x0019,
+ STATISTICS_INDEX_REG_MAC1_RX_STAT2 = 0x001a,
+ STATISTICS_INDEX_REG_MAC1_RX_STAT3 = 0x001b,
+ STATISTICS_INDEX_REG_MAC1_RX_ERR_CRC = 0x001c,
+ STATISTICS_INDEX_REG_MAC1_RX_ERR_ENC = 0x001d,
+ STATISTICS_INDEX_REG_MAC1_RX_ERR_LEN = 0x001e,
+ STATISTICS_INDEX_REG_MAC1_RX_STAT4 = 0x001f,
+ STATISTICS_INDEX_REG_IP_TX_PKTS = 0x0020,
+ STATISTICS_INDEX_REG_IP_TX_BYTES = 0x0021,
+ STATISTICS_INDEX_REG_IP_TX_FRAG = 0x0022,
+ STATISTICS_INDEX_REG_IP_RX_PKTS = 0x0023,
+ STATISTICS_INDEX_REG_IP_RX_BYTES = 0x0024,
+ STATISTICS_INDEX_REG_IP_RX_FRAG = 0x0025,
+ STATISTICS_INDEX_REG_IP_DGRM_REASSEMBLY = 0x0026,
+ STATISTICS_INDEX_REG_IP_V6_RX_PKTS = 0x0027,
+ STATISTICS_INDEX_REG_IP_RX_PKTERR = 0x0028,
+ STATISTICS_INDEX_REG_IP_REASSEMBLY_ERR = 0x0029,
+ STATISTICS_INDEX_REG_TCP_TX_SEG = 0x0030,
+ STATISTICS_INDEX_REG_TCP_TX_BYTES = 0x0031,
+ STATISTICS_INDEX_REG_TCP_RX_SEG = 0x0032,
+ STATISTICS_INDEX_REG_TCP_RX_BYTES = 0x0033,
+ STATISTICS_INDEX_REG_TCP_TIMER_EXP = 0x0034,
+ STATISTICS_INDEX_REG_TCP_RX_ACK = 0x0035,
+ STATISTICS_INDEX_REG_TCP_TX_ACK = 0x0036,
+ STATISTICS_INDEX_REG_TCP_RX_ERR = 0x0037,
+ STATISTICS_INDEX_REG_TCP_RX_WIN_PROBE = 0x0038,
+ STATISTICS_INDEX_REG_TCP_ECC_ERR_CORR = 0x003f,
+};
+
+enum {
+ PORT_FATAL_ERROR_STATUS_OFB_RE_MAC0 = 0x00000001,
+ PORT_FATAL_ERROR_STATUS_OFB_RE_MAC1 = 0x00000002,
+ PORT_FATAL_ERROR_STATUS_OFB_WE = 0x00000004,
+ PORT_FATAL_ERROR_STATUS_IFB_RE = 0x00000008,
+ PORT_FATAL_ERROR_STATUS_IFB_WE_MAC0 = 0x00000010,
+ PORT_FATAL_ERROR_STATUS_IFB_WE_MAC1 = 0x00000020,
+ PORT_FATAL_ERROR_STATUS_ODE_RE = 0x00000040,
+ PORT_FATAL_ERROR_STATUS_ODE_WE = 0x00000080,
+ PORT_FATAL_ERROR_STATUS_IDE_RE = 0x00000100,
+ PORT_FATAL_ERROR_STATUS_IDE_WE = 0x00000200,
+ PORT_FATAL_ERROR_STATUS_SDE_RE = 0x00000400,
+ PORT_FATAL_ERROR_STATUS_SDE_WE = 0x00000800,
+ PORT_FATAL_ERROR_STATUS_BLE = 0x00001000,
+ PORT_FATAL_ERROR_STATUS_SPE = 0x00002000,
+ PORT_FATAL_ERROR_STATUS_EP0 = 0x00004000,
+ PORT_FATAL_ERROR_STATUS_EP1 = 0x00008000,
+ PORT_FATAL_ERROR_STATUS_ICE = 0x00010000,
+ PORT_FATAL_ERROR_STATUS_ILE = 0x00020000,
+ PORT_FATAL_ERROR_STATUS_OPE = 0x00040000,
+ PORT_FATAL_ERROR_STATUS_TA = 0x00080000,
+ PORT_FATAL_ERROR_STATUS_MA = 0x00100000,
+ PORT_FATAL_ERROR_STATUS_SCE = 0x00200000,
+ PORT_FATAL_ERROR_STATUS_RPE = 0x00400000,
+ PORT_FATAL_ERROR_STATUS_MPE = 0x00800000,
+ PORT_FATAL_ERROR_STATUS_OCE = 0x01000000,
+};
+
+/*
+ * port control and status page - page 0
+ */
+
+struct ql3xxx_port_registers {
+ struct ql3xxx_common_registers CommonRegs;
+
+ u32 ExternalHWConfig;
+ u32 InternalChipConfig;
+ u32 portControl;
+ u32 portStatus;
+ u32 macAddrIndirectPtrReg;
+ u32 macAddrDataReg;
+ u32 macMIIMgmtControlReg;
+ u32 macMIIMgmtAddrReg;
+ u32 macMIIMgmtDataReg;
+ u32 macMIIStatusReg;
+ u32 mac0ConfigReg;
+ u32 mac0IpgIfgReg;
+ u32 mac0HalfDuplexReg;
+ u32 mac0MaxFrameLengthReg;
+ u32 mac0PauseThresholdReg;
+ u32 mac1ConfigReg;
+ u32 mac1IpgIfgReg;
+ u32 mac1HalfDuplexReg;
+ u32 mac1MaxFrameLengthReg;
+ u32 mac1PauseThresholdReg;
+ u32 ipAddrIndexReg;
+ u32 ipAddrDataReg;
+ u32 ipReassemblyTimeout;
+ u32 tcpMaxWindow;
+ u32 currentTcpTimestamp[2];
+ u32 internalRamRWAddrReg;
+ u32 internalRamWDataReg;
+ u32 reclaimedBufferAddrRegLow;
+ u32 reclaimedBufferAddrRegHigh;
+ u32 reserved[2];
+ u32 fpgaRevID;
+ u32 localRamAddr;
+ u32 localRamDataAutoIncr;
+ u32 localRamDataNonIncr;
+ u32 gpOutput;
+ u32 gpInput;
+ u32 probeMuxAddr;
+ u32 probeMuxData;
+ u32 statisticsIndexReg;
+ u32 statisticsReadDataRegAutoIncr;
+ u32 statisticsReadDataRegNoIncr;
+ u32 PortFatalErrStatus;
+};
+
+/*
+ * port host memory config page - page 1
+ */
+struct ql3xxx_host_memory_registers {
+ struct ql3xxx_common_registers CommonRegs;
+
+ u32 reserved[12];
+
+ /* Network Request Queue */
+ u32 reqConsumerIndex;
+ u32 reqConsumerIndexAddrLow;
+ u32 reqConsumerIndexAddrHigh;
+ u32 reqBaseAddrLow;
+ u32 reqBaseAddrHigh;
+ u32 reqLength;
+
+ /* Network Completion Queue */
+ u32 rspProducerIndex;
+ u32 rspProducerIndexAddrLow;
+ u32 rspProducerIndexAddrHigh;
+ u32 rspBaseAddrLow;
+ u32 rspBaseAddrHigh;
+ u32 rspLength;
+
+ /* RX Large Buffer Queue */
+ u32 rxLargeQConsumerIndex;
+ u32 rxLargeQBaseAddrLow;
+ u32 rxLargeQBaseAddrHigh;
+ u32 rxLargeQLength;
+ u32 rxLargeBufferLength;
+
+ /* RX Small Buffer Queue */
+ u32 rxSmallQConsumerIndex;
+ u32 rxSmallQBaseAddrLow;
+ u32 rxSmallQBaseAddrHigh;
+ u32 rxSmallQLength;
+ u32 rxSmallBufferLength;
+
+};
+
+/*
+ * port local RAM page - page 2
+ */
+struct ql3xxx_local_ram_registers {
+ struct ql3xxx_common_registers CommonRegs;
+ u32 bufletSize;
+ u32 maxBufletCount;
+ u32 currentBufletCount;
+ u32 reserved;
+ u32 freeBufletThresholdLow;
+ u32 freeBufletThresholdHigh;
+ u32 ipHashTableBase;
+ u32 ipHashTableCount;
+ u32 tcpHashTableBase;
+ u32 tcpHashTableCount;
+ u32 ncbBase;
+ u32 maxNcbCount;
+ u32 currentNcbCount;
+ u32 drbBase;
+ u32 maxDrbCount;
+ u32 currentDrbCount;
+};
+
+/*
+ * definitions for Semaphore bits in Semaphore/Serial NVRAM interface register
+ */
+
+#define LS_64BITS(x) (u32)(0xffffffff & ((u64)x))
+#define MS_64BITS(x) (u32)(0xffffffff & (((u64)x)>>16>>16) )
+
+/*
+ * I/O register
+ */
+
+enum {
+ CONTROL_REG = 0,
+ STATUS_REG = 1,
+ PHY_STAT_LINK_UP = 0x0004,
+ PHY_CTRL_LOOPBACK = 0x4000,
+
+ PETBI_CONTROL_REG = 0x00,
+ PETBI_CTRL_SOFT_RESET = 0x8000,
+ PETBI_CTRL_AUTO_NEG = 0x1000,
+ PETBI_CTRL_RESTART_NEG = 0x0200,
+ PETBI_CTRL_FULL_DUPLEX = 0x0100,
+ PETBI_CTRL_SPEED_1000 = 0x0040,
+
+ PETBI_STATUS_REG = 0x01,
+ PETBI_STAT_NEG_DONE = 0x0020,
+ PETBI_STAT_LINK_UP = 0x0004,
+
+ PETBI_NEG_ADVER = 0x04,
+ PETBI_NEG_PAUSE = 0x0080,
+ PETBI_NEG_PAUSE_MASK = 0x0180,
+ PETBI_NEG_DUPLEX = 0x0020,
+ PETBI_NEG_DUPLEX_MASK = 0x0060,
+
+ PETBI_NEG_PARTNER = 0x05,
+ PETBI_NEG_ERROR_MASK = 0x3000,
+
+ PETBI_EXPANSION_REG = 0x06,
+ PETBI_EXP_PAGE_RX = 0x0002,
+
+ PETBI_TBI_CTRL = 0x11,
+ PETBI_TBI_RESET = 0x8000,
+ PETBI_TBI_AUTO_SENSE = 0x0100,
+ PETBI_TBI_SERDES_MODE = 0x0010,
+ PETBI_TBI_SERDES_WRAP = 0x0002,
+
+ AUX_CONTROL_STATUS = 0x1c,
+ PHY_AUX_NEG_DONE = 0x8000,
+ PHY_NEG_PARTNER = 5,
+ PHY_AUX_DUPLEX_STAT = 0x0020,
+ PHY_AUX_SPEED_STAT = 0x0018,
+ PHY_AUX_NO_HW_STRAP = 0x0004,
+ PHY_AUX_RESET_STICK = 0x0002,
+ PHY_NEG_PAUSE = 0x0400,
+ PHY_CTRL_SOFT_RESET = 0x8000,
+ PHY_NEG_ADVER = 4,
+ PHY_NEG_ADV_SPEED = 0x01e0,
+ PHY_CTRL_RESTART_NEG = 0x0200,
+};
+enum {
+/* AM29LV Flash definitions */
+ FM93C56A_START = 0x1,
+/* Commands */
+ FM93C56A_READ = 0x2,
+ FM93C56A_WEN = 0x0,
+ FM93C56A_WRITE = 0x1,
+ FM93C56A_WRITE_ALL = 0x0,
+ FM93C56A_WDS = 0x0,
+ FM93C56A_ERASE = 0x3,
+ FM93C56A_ERASE_ALL = 0x0,
+/* Command Extentions */
+ FM93C56A_WEN_EXT = 0x3,
+ FM93C56A_WRITE_ALL_EXT = 0x1,
+ FM93C56A_WDS_EXT = 0x0,
+ FM93C56A_ERASE_ALL_EXT = 0x2,
+/* Special Bits */
+ FM93C56A_READ_DUMMY_BITS = 1,
+ FM93C56A_READY = 0,
+ FM93C56A_BUSY = 1,
+ FM93C56A_CMD_BITS = 2,
+/* AM29LV Flash definitions */
+ FM93C56A_SIZE_8 = 0x100,
+ FM93C56A_SIZE_16 = 0x80,
+ FM93C66A_SIZE_8 = 0x200,
+ FM93C66A_SIZE_16 = 0x100,
+ FM93C86A_SIZE_16 = 0x400,
+/* Address Bits */
+ FM93C56A_NO_ADDR_BITS_16 = 8,
+ FM93C56A_NO_ADDR_BITS_8 = 9,
+ FM93C86A_NO_ADDR_BITS_16 = 10,
+/* Data Bits */
+ FM93C56A_DATA_BITS_16 = 16,
+ FM93C56A_DATA_BITS_8 = 8,
+};
+enum {
+/* Auburn Bits */
+ AUBURN_EEPROM_DI = 0x8,
+ AUBURN_EEPROM_DI_0 = 0x0,
+ AUBURN_EEPROM_DI_1 = 0x8,
+ AUBURN_EEPROM_DO = 0x4,
+ AUBURN_EEPROM_DO_0 = 0x0,
+ AUBURN_EEPROM_DO_1 = 0x4,
+ AUBURN_EEPROM_CS = 0x2,
+ AUBURN_EEPROM_CS_0 = 0x0,
+ AUBURN_EEPROM_CS_1 = 0x2,
+ AUBURN_EEPROM_CLK_RISE = 0x1,
+ AUBURN_EEPROM_CLK_FALL = 0x0,
+};
+enum {EEPROM_SIZE = FM93C86A_SIZE_16,
+ EEPROM_NO_ADDR_BITS = FM93C86A_NO_ADDR_BITS_16,
+ EEPROM_NO_DATA_BITS = FM93C56A_DATA_BITS_16,
+};
+
+/*
+ * MAC Config data structure
+ */
+ struct eeprom_port_cfg {
+ u16 etherMtu_mac;
+ u16 pauseThreshold_mac;
+ u16 resumeThreshold_mac;
+ u16 portConfiguration;
+#define PORT_CONFIG_AUTO_NEG_ENABLED 0x8000
+#define PORT_CONFIG_SYM_PAUSE_ENABLED 0x4000
+#define PORT_CONFIG_FULL_DUPLEX_ENABLED 0x2000
+#define PORT_CONFIG_HALF_DUPLEX_ENABLED 0x1000
+#define PORT_CONFIG_1000MB_SPEED 0x0400
+#define PORT_CONFIG_100MB_SPEED 0x0200
+#define PORT_CONFIG_10MB_SPEED 0x0100
+#define PORT_CONFIG_LINK_SPEED_MASK 0x0F00
+ u16 reserved[12];
+
+};
+
+/*
+ * BIOS data structure
+ */
+struct eeprom_bios_cfg {
+ u16 SpinDlyEn:1, disBios:1, EnMemMap:1, EnSelectBoot:1, Reserved:12;
+
+ u8 bootID0:7, boodID0Valid:1;
+ u8 bootLun0[8];
+
+ u8 bootID1:7, boodID1Valid:1;
+ u8 bootLun1[8];
+
+ u16 MaxLunsTrgt;
+ u8 reserved[10];
+};
+
+/*
+ * Function Specific Data structure
+ */
+struct eeprom_function_cfg {
+ u8 reserved[30];
+ u8 macAddress[6];
+ u8 macAddressSecondary[6];
+
+ u16 subsysVendorId;
+ u16 subsysDeviceId;
+};
+
+/*
+ * EEPROM format
+ */
+struct eeprom_data {
+ u8 asicId[4];
+ u8 version;
+ u8 numPorts;
+ u16 boardId;
+
+#define EEPROM_BOARDID_STR_SIZE 16
+#define EEPROM_SERIAL_NUM_SIZE 16
+
+ u8 boardIdStr[16];
+ u8 serialNumber[16];
+ u16 extHwConfig;
+ struct eeprom_port_cfg macCfg_port0;
+ struct eeprom_port_cfg macCfg_port1;
+ u16 bufletSize;
+ u16 bufletCount;
+ u16 tcpWindowThreshold50;
+ u16 tcpWindowThreshold25;
+ u16 tcpWindowThreshold0;
+ u16 ipHashTableBaseHi;
+ u16 ipHashTableBaseLo;
+ u16 ipHashTableSize;
+ u16 tcpHashTableBaseHi;
+ u16 tcpHashTableBaseLo;
+ u16 tcpHashTableSize;
+ u16 ncbTableBaseHi;
+ u16 ncbTableBaseLo;
+ u16 ncbTableSize;
+ u16 drbTableBaseHi;
+ u16 drbTableBaseLo;
+ u16 drbTableSize;
+ u16 reserved_142[4];
+ u16 ipReassemblyTimeout;
+ u16 tcpMaxWindowSize;
+ u16 ipSecurity;
+#define IPSEC_CONFIG_PRESENT 0x0001
+ u8 reserved_156[294];
+ u16 qDebug[8];
+ struct eeprom_function_cfg funcCfg_fn0;
+ u16 reserved_510;
+ u8 oemSpace[432];
+ struct eeprom_bios_cfg biosCfg_fn1;
+ struct eeprom_function_cfg funcCfg_fn1;
+ u16 reserved_1022;
+ u8 reserved_1024[464];
+ struct eeprom_function_cfg funcCfg_fn2;
+ u16 reserved_1534;
+ u8 reserved_1536[432];
+ struct eeprom_bios_cfg biosCfg_fn3;
+ struct eeprom_function_cfg funcCfg_fn3;
+ u16 checksum;
+};
+
+/*
+ * General definitions...
+ */
+
+/*
+ * Below are a number compiler switches for controlling driver behavior.
+ * Some are not supported under certain conditions and are notated as such.
+ */
+
+#define QL3XXX_VENDOR_ID 0x1077
+#define QL3022_DEVICE_ID 0x3022
+
+/* MTU & Frame Size stuff */
+#define NORMAL_MTU_SIZE ETH_DATA_LEN
+#define JUMBO_MTU_SIZE 9000
+#define VLAN_ID_LEN 2
+
+/* Request Queue Related Definitions */
+#define NUM_REQ_Q_ENTRIES 256 /* so that 64 * 64 = 4096 (1 page) */
+
+/* Response Queue Related Definitions */
+#define NUM_RSP_Q_ENTRIES 256 /* so that 256 * 16 = 4096 (1 page) */
+
+/* Transmit and Receive Buffers */
+#define NUM_LBUFQ_ENTRIES 128
+#define NUM_SBUFQ_ENTRIES 64
+#define QL_SMALL_BUFFER_SIZE 32
+#define QL_ADDR_ELE_PER_BUFQ_ENTRY \
+(sizeof(struct lrg_buf_q_entry) / sizeof(struct bufq_addr_element))
+ /* Each send has at least control block. This is how many we keep. */
+#define NUM_SMALL_BUFFERS NUM_SBUFQ_ENTRIES * QL_ADDR_ELE_PER_BUFQ_ENTRY
+#define NUM_LARGE_BUFFERS NUM_LBUFQ_ENTRIES * QL_ADDR_ELE_PER_BUFQ_ENTRY
+#define QL_HEADER_SPACE 32 /* make header space at top of skb. */
+/*
+ * Large & Small Buffers for Receives
+ */
+struct lrg_buf_q_entry {
+
+ u32 addr0_lower;
+#define IAL_LAST_ENTRY 0x00000001
+#define IAL_CONT_ENTRY 0x00000002
+#define IAL_FLAG_MASK 0x00000003
+ u32 addr0_upper;
+ u32 addr1_lower;
+ u32 addr1_upper;
+ u32 addr2_lower;
+ u32 addr2_upper;
+ u32 addr3_lower;
+ u32 addr3_upper;
+ u32 addr4_lower;
+ u32 addr4_upper;
+ u32 addr5_lower;
+ u32 addr5_upper;
+ u32 addr6_lower;
+ u32 addr6_upper;
+ u32 addr7_lower;
+ u32 addr7_upper;
+
+};
+
+struct bufq_addr_element {
+ u32 addr_low;
+ u32 addr_high;
+};
+
+#define QL_NO_RESET 0
+#define QL_DO_RESET 1
+
+enum link_state_t {
+ LS_UNKNOWN = 0,
+ LS_DOWN,
+ LS_DEGRADE,
+ LS_RECOVER,
+ LS_UP,
+};
+
+struct ql_rcv_buf_cb {
+ struct ql_rcv_buf_cb *next;
+ struct sk_buff *skb;
+ DECLARE_PCI_UNMAP_ADDR(mapaddr);
+ DECLARE_PCI_UNMAP_LEN(maplen);
+ __le32 buf_phy_addr_low;
+ __le32 buf_phy_addr_high;
+ int index;
+};
+
+struct ql_tx_buf_cb {
+ struct sk_buff *skb;
+ struct ob_mac_iocb_req *queue_entry ;
+ DECLARE_PCI_UNMAP_ADDR(mapaddr);
+ DECLARE_PCI_UNMAP_LEN(maplen);
+};
+
+/* definitions for type field */
+#define QL_BUF_TYPE_MACIOCB 0x01
+#define QL_BUF_TYPE_IPIOCB 0x02
+#define QL_BUF_TYPE_TCPIOCB 0x03
+
+/* qdev->flags definitions. */
+enum { QL_RESET_DONE = 1, /* Reset finished. */
+ QL_RESET_ACTIVE = 2, /* Waiting for reset to finish. */
+ QL_RESET_START = 3, /* Please reset the chip. */
+ QL_RESET_PER_SCSI = 4, /* SCSI driver requests reset. */
+ QL_TX_TIMEOUT = 5, /* Timeout in progress. */
+ QL_LINK_MASTER = 6, /* This driver controls the link. */
+ QL_ADAPTER_UP = 7, /* Adapter has been brought up. */
+ QL_THREAD_UP = 8, /* This flag is available. */
+ QL_LINK_UP = 9, /* Link Status. */
+ QL_ALLOC_REQ_RSP_Q_DONE = 10,
+ QL_ALLOC_BUFQS_DONE = 11,
+ QL_ALLOC_SMALL_BUF_DONE = 12,
+ QL_LINK_OPTICAL = 13,
+ QL_MSI_ENABLED = 14,
+};
+
+/*
+ * ql3_adapter - The main Adapter structure definition.
+ * This structure has all fields relevant to the hardware.
+ */
+
+struct ql3_adapter {
+ u32 reserved_00;
+ unsigned long flags;
+
+ /* PCI Configuration information for this device */
+ struct pci_dev *pdev;
+ struct net_device *ndev; /* Parent NET device */
+
+ /* Hardware information */
+ u8 chip_rev_id;
+ u8 pci_slot;
+ u8 pci_width;
+ u8 pci_x;
+ u32 msi;
+ int index;
+ struct timer_list adapter_timer; /* timer used for various functions */
+
+ spinlock_t adapter_lock;
+ spinlock_t hw_lock;
+
+ /* PCI Bus Relative Register Addresses */
+ u8 *mmap_virt_base; /* stores return value from ioremap() */
+ struct ql3xxx_port_registers __iomem *mem_map_registers;
+ u32 current_page; /* tracks current register page */
+
+ u32 msg_enable;
+ u8 reserved_01[2];
+ u8 reserved_02[2];
+
+ /* Page for Shadow Registers */
+ void *shadow_reg_virt_addr;
+ dma_addr_t shadow_reg_phy_addr;
+
+ /* Net Request Queue */
+ u32 req_q_size;
+ u32 reserved_03;
+ struct ob_mac_iocb_req *req_q_virt_addr;
+ dma_addr_t req_q_phy_addr;
+ u16 req_producer_index;
+ u16 reserved_04;
+ u16 *preq_consumer_index;
+ u32 req_consumer_index_phy_addr_high;
+ u32 req_consumer_index_phy_addr_low;
+ atomic_t tx_count;
+ struct ql_tx_buf_cb tx_buf[NUM_REQ_Q_ENTRIES];
+
+ /* Net Response Queue */
+ u32 rsp_q_size;
+ u32 eeprom_cmd_data;
+ struct net_rsp_iocb *rsp_q_virt_addr;
+ dma_addr_t rsp_q_phy_addr;
+ struct net_rsp_iocb *rsp_current;
+ u16 rsp_consumer_index;
+ u16 reserved_06;
+ u32 *prsp_producer_index;
+ u32 rsp_producer_index_phy_addr_high;
+ u32 rsp_producer_index_phy_addr_low;
+
+ /* Large Buffer Queue */
+ u32 lrg_buf_q_alloc_size;
+ u32 lrg_buf_q_size;
+ void *lrg_buf_q_alloc_virt_addr;
+ void *lrg_buf_q_virt_addr;
+ dma_addr_t lrg_buf_q_alloc_phy_addr;
+ dma_addr_t lrg_buf_q_phy_addr;
+ u32 lrg_buf_q_producer_index;
+ u32 lrg_buf_release_cnt;
+ struct bufq_addr_element *lrg_buf_next_free;
+
+ /* Large (Receive) Buffers */
+ struct ql_rcv_buf_cb lrg_buf[NUM_LARGE_BUFFERS];
+ struct ql_rcv_buf_cb *lrg_buf_free_head;
+ struct ql_rcv_buf_cb *lrg_buf_free_tail;
+ u32 lrg_buf_free_count;
+ u32 lrg_buffer_len;
+ u32 lrg_buf_index;
+ u32 lrg_buf_skb_check;
+
+ /* Small Buffer Queue */
+ u32 small_buf_q_alloc_size;
+ u32 small_buf_q_size;
+ u32 small_buf_q_producer_index;
+ void *small_buf_q_alloc_virt_addr;
+ void *small_buf_q_virt_addr;
+ dma_addr_t small_buf_q_alloc_phy_addr;
+ dma_addr_t small_buf_q_phy_addr;
+ u32 small_buf_index;
+
+ /* Small (Receive) Buffers */
+ void *small_buf_virt_addr;
+ dma_addr_t small_buf_phy_addr;
+ u32 small_buf_phy_addr_low;
+ u32 small_buf_phy_addr_high;
+ u32 small_buf_release_cnt;
+ u32 small_buf_total_size;
+
+ /* ISR related, saves status for DPC. */
+ u32 control_status;
+
+ struct eeprom_data nvram_data;
+ struct timer_list ioctl_timer;
+ u32 port_link_state;
+ u32 last_rsp_offset;
+
+ /* 4022 specific */
+ u32 mac_index; /* Driver's MAC number can be 0 or 1 for first and second networking functions respectively */
+ u32 PHYAddr; /* Address of PHY 0x1e00 Port 0 and 0x1f00 Port 1 */
+ u32 mac_ob_opcode; /* Opcode to use on mac transmission */
+ u32 tcp_ob_opcode; /* Opcode to use on tcp transmission */
+ u32 update_ob_opcode; /* Opcode to use for updating NCB */
+ u32 mb_bit_mask; /* MA Bits mask to use on transmission */
+ u32 numPorts;
+ struct net_device_stats stats;
+ struct workqueue_struct *workqueue;
+ struct work_struct reset_work;
+ struct work_struct tx_timeout_work;
+ u32 max_frame_size;
+};
+
+#endif /* _QLA3XXX_H_ */
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index 4c2f575..5722a56 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -2809,7 +2809,7 @@
static int __init
rtl8169_init_module(void)
{
- return pci_module_init(&rtl8169_pci_driver);
+ return pci_register_driver(&rtl8169_pci_driver);
}
static void __exit
diff --git a/drivers/net/rrunner.c b/drivers/net/rrunner.c
index c3ed734..31bcdad 100644
--- a/drivers/net/rrunner.c
+++ b/drivers/net/rrunner.c
@@ -1736,7 +1736,7 @@
static int __init rr_init_module(void)
{
- return pci_module_init(&rr_driver);
+ return pci_register_driver(&rr_driver);
}
static void __exit rr_cleanup_module(void)
diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index e72e0e0..c16f915 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -7233,7 +7233,7 @@
int __init s2io_starter(void)
{
- return pci_module_init(&s2io_driver);
+ return pci_register_driver(&s2io_driver);
}
/**
diff --git a/drivers/net/saa9730.c b/drivers/net/saa9730.c
index b2acedb..c479b07 100644
--- a/drivers/net/saa9730.c
+++ b/drivers/net/saa9730.c
@@ -1131,7 +1131,7 @@
static int __init saa9730_init(void)
{
- return pci_module_init(&saa9730_driver);
+ return pci_register_driver(&saa9730_driver);
}
static void __exit saa9730_cleanup(void)
diff --git a/drivers/net/sis190.c b/drivers/net/sis190.c
index df0cbeb..16e30d5 100644
--- a/drivers/net/sis190.c
+++ b/drivers/net/sis190.c
@@ -1871,7 +1871,7 @@
static int __init sis190_init_module(void)
{
- return pci_module_init(&sis190_pci_driver);
+ return pci_register_driver(&sis190_pci_driver);
}
static void __exit sis190_cleanup_module(void)
diff --git a/drivers/net/sis900.c b/drivers/net/sis900.c
index 29ee7ff..6af5028 100644
--- a/drivers/net/sis900.c
+++ b/drivers/net/sis900.c
@@ -134,6 +134,7 @@
{ "AMD 79C901 10BASE-T PHY", 0x0000, 0x6B70, LAN },
{ "AMD 79C901 HomePNA PHY", 0x0000, 0x6B90, HOME},
{ "ICS LAN PHY", 0x0015, 0xF440, LAN },
+ { "ICS LAN PHY", 0x0143, 0xBC70, LAN },
{ "NS 83851 PHY", 0x2000, 0x5C20, MIX },
{ "NS 83847 PHY", 0x2000, 0x5C30, MIX },
{ "Realtek RTL8201 PHY", 0x0000, 0x8200, LAN },
@@ -2495,7 +2496,7 @@
printk(version);
#endif
- return pci_module_init(&sis900_pci_driver);
+ return pci_register_driver(&sis900_pci_driver);
}
static void __exit sis900_cleanup_module(void)
diff --git a/drivers/net/sk98lin/skge.c b/drivers/net/sk98lin/skge.c
index ee62845..49e76c7 100644
--- a/drivers/net/sk98lin/skge.c
+++ b/drivers/net/sk98lin/skge.c
@@ -5133,7 +5133,7 @@
static int __init skge_init(void)
{
- return pci_module_init(&skge_driver);
+ return pci_register_driver(&skge_driver);
}
static void __exit skge_exit(void)
diff --git a/drivers/net/skfp/skfddi.c b/drivers/net/skfp/skfddi.c
index b5714a60..8e4d184 100644
--- a/drivers/net/skfp/skfddi.c
+++ b/drivers/net/skfp/skfddi.c
@@ -2280,7 +2280,7 @@
static int __init skfd_init(void)
{
- return pci_module_init(&skfddi_pci_driver);
+ return pci_register_driver(&skfddi_pci_driver);
}
static void __exit skfd_exit(void)
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index ad878df..a1fc043 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -43,7 +43,7 @@
#include "skge.h"
#define DRV_NAME "skge"
-#define DRV_VERSION "1.6"
+#define DRV_VERSION "1.7"
#define PFX DRV_NAME " "
#define DEFAULT_TX_RING_SIZE 128
@@ -827,7 +827,8 @@
do {
struct sk_buff *skb;
- skb = alloc_skb(skge->rx_buf_size + NET_IP_ALIGN, GFP_KERNEL);
+ skb = __dev_alloc_skb(skge->rx_buf_size + NET_IP_ALIGN,
+ GFP_KERNEL);
if (!skb)
return -ENOMEM;
@@ -2609,7 +2610,7 @@
goto error;
if (len < RX_COPY_THRESHOLD) {
- skb = alloc_skb(len + 2, GFP_ATOMIC);
+ skb = dev_alloc_skb(len + 2);
if (!skb)
goto resubmit;
@@ -2624,7 +2625,7 @@
skge_rx_reuse(e, skge->rx_buf_size);
} else {
struct sk_buff *nskb;
- nskb = alloc_skb(skge->rx_buf_size + NET_IP_ALIGN, GFP_ATOMIC);
+ nskb = dev_alloc_skb(skge->rx_buf_size + NET_IP_ALIGN);
if (!nskb)
goto resubmit;
@@ -2747,7 +2748,7 @@
spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= rxirqmask[skge->port];
skge_write32(hw, B0_IMSK, hw->intr_mask);
- mmiowb();
+ skge_read32(hw, B0_IMSK);
spin_unlock_irq(&hw->hw_lock);
return 0;
@@ -2881,6 +2882,7 @@
spin_lock_irq(&hw->hw_lock);
hw->intr_mask |= IS_EXT_REG;
skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
spin_unlock_irq(&hw->hw_lock);
}
@@ -2955,6 +2957,7 @@
skge_error_irq(hw);
skge_write32(hw, B0_IMSK, hw->intr_mask);
+ skge_read32(hw, B0_IMSK);
spin_unlock(&hw->hw_lock);
return IRQ_HANDLED;
@@ -3106,7 +3109,6 @@
else
hw->ram_size = t8 * 4096;
- spin_lock_init(&hw->hw_lock);
hw->intr_mask = IS_HW_ERR | IS_EXT_REG | IS_PORT_1;
if (hw->ports > 1)
hw->intr_mask |= IS_PORT_2;
@@ -3332,6 +3334,7 @@
hw->pdev = pdev;
mutex_init(&hw->phy_mutex);
INIT_WORK(&hw->phy_work, skge_extirq, hw);
+ spin_lock_init(&hw->hw_lock);
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
@@ -3340,23 +3343,16 @@
goto err_out_free_hw;
}
- err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, DRV_NAME, hw);
- if (err) {
- printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
- pci_name(pdev), pdev->irq);
- goto err_out_iounmap;
- }
- pci_set_drvdata(pdev, hw);
-
err = skge_reset(hw);
if (err)
- goto err_out_free_irq;
+ goto err_out_iounmap;
printk(KERN_INFO PFX DRV_VERSION " addr 0x%llx irq %d chip %s rev %d\n",
(unsigned long long)pci_resource_start(pdev, 0), pdev->irq,
skge_board_name(hw), hw->chip_rev);
- if ((dev = skge_devinit(hw, 0, using_dac)) == NULL)
+ dev = skge_devinit(hw, 0, using_dac);
+ if (!dev)
goto err_out_led_off;
if (!is_valid_ether_addr(dev->dev_addr)) {
@@ -3366,7 +3362,6 @@
goto err_out_free_netdev;
}
-
err = register_netdev(dev);
if (err) {
printk(KERN_ERR PFX "%s: cannot register net device\n",
@@ -3374,6 +3369,12 @@
goto err_out_free_netdev;
}
+ err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw);
+ if (err) {
+ printk(KERN_ERR PFX "%s: cannot assign irq %d\n",
+ dev->name, pdev->irq);
+ goto err_out_unregister;
+ }
skge_show_addr(dev);
if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) {
@@ -3386,15 +3387,16 @@
free_netdev(dev1);
}
}
+ pci_set_drvdata(pdev, hw);
return 0;
+err_out_unregister:
+ unregister_netdev(dev);
err_out_free_netdev:
free_netdev(dev);
err_out_led_off:
skge_write16(hw, B0_LED, LED_STAT_OFF);
-err_out_free_irq:
- free_irq(pdev->irq, hw);
err_out_iounmap:
iounmap(hw->regs);
err_out_free_hw:
@@ -3424,6 +3426,7 @@
spin_lock_irq(&hw->hw_lock);
hw->intr_mask = 0;
skge_write32(hw, B0_IMSK, 0);
+ skge_read32(hw, B0_IMSK);
spin_unlock_irq(&hw->hw_lock);
skge_write16(hw, B0_LED, LED_STAT_OFF);
@@ -3449,26 +3452,25 @@
struct skge_hw *hw = pci_get_drvdata(pdev);
int i, wol = 0;
- for (i = 0; i < 2; i++) {
+ pci_save_state(pdev);
+ for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
+ if (netif_running(dev)) {
struct skge_port *skge = netdev_priv(dev);
- if (netif_running(dev)) {
- netif_carrier_off(dev);
- if (skge->wol)
- netif_stop_queue(dev);
- else
- skge_down(dev);
- }
- netif_device_detach(dev);
+
+ netif_carrier_off(dev);
+ if (skge->wol)
+ netif_stop_queue(dev);
+ else
+ skge_down(dev);
wol |= skge->wol;
}
+ netif_device_detach(dev);
}
- pci_save_state(pdev);
+ skge_write32(hw, B0_IMSK, 0);
pci_enable_wake(pdev, pci_choose_state(pdev, state), wol);
- pci_disable_device(pdev);
pci_set_power_state(pdev, pci_choose_state(pdev, state));
return 0;
@@ -3477,23 +3479,33 @@
static int skge_resume(struct pci_dev *pdev)
{
struct skge_hw *hw = pci_get_drvdata(pdev);
- int i;
+ int i, err;
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
pci_enable_wake(pdev, PCI_D0, 0);
- skge_reset(hw);
+ err = skge_reset(hw);
+ if (err)
+ goto out;
- for (i = 0; i < 2; i++) {
+ for (i = 0; i < hw->ports; i++) {
struct net_device *dev = hw->dev[i];
- if (dev) {
- netif_device_attach(dev);
- if (netif_running(dev) && skge_up(dev))
+
+ netif_device_attach(dev);
+ if (netif_running(dev)) {
+ err = skge_up(dev);
+
+ if (err) {
+ printk(KERN_ERR PFX "%s: could not up: %d\n",
+ dev->name, err);
dev_close(dev);
+ goto out;
+ }
}
}
- return 0;
+out:
+ return err;
}
#endif
@@ -3510,7 +3522,7 @@
static int __init skge_init_module(void)
{
- return pci_module_init(&skge_driver);
+ return pci_register_driver(&skge_driver);
}
static void __exit skge_cleanup_module(void)
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 933e87f..f37fe8f 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -50,7 +50,7 @@
#include "sky2.h"
#define DRV_NAME "sky2"
-#define DRV_VERSION "1.5"
+#define DRV_VERSION "1.7"
#define PFX DRV_NAME " "
/*
@@ -121,6 +121,11 @@
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) },
{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) },
+ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) },
{ 0 }
};
@@ -190,7 +195,6 @@
static void sky2_set_power_state(struct sky2_hw *hw, pci_power_t state)
{
u16 power_control;
- u32 reg1;
int vaux;
pr_debug("sky2_set_power_state %d\n", state);
@@ -223,20 +227,9 @@
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
- /* Turn off phy power saving */
- reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
-
- /* looks like this XL is back asswards .. */
- if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) {
- reg1 |= PCI_Y2_PHY1_COMA;
- if (hw->ports > 1)
- reg1 |= PCI_Y2_PHY2_COMA;
- }
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- udelay(100);
-
if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ u32 reg1;
+
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
reg1 = sky2_pci_read32(hw, PCI_DEV_REG4);
reg1 &= P_ASPM_CONTROL_MSK;
@@ -248,15 +241,6 @@
case PCI_D3hot:
case PCI_D3cold:
- /* Turn on phy power saving */
- reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
- if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
- reg1 &= ~(PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- else
- reg1 |= (PCI_Y2_PHY1_POWD | PCI_Y2_PHY2_POWD);
- sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
- udelay(100);
-
if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
else
@@ -280,7 +264,7 @@
sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
}
-static void sky2_phy_reset(struct sky2_hw *hw, unsigned port)
+static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
{
u16 reg;
@@ -528,6 +512,29 @@
gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK);
}
+static void sky2_phy_power(struct sky2_hw *hw, unsigned port, int onoff)
+{
+ u32 reg1;
+ static const u32 phy_power[]
+ = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD };
+
+ /* looks like this XL is back asswards .. */
+ if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1)
+ onoff = !onoff;
+
+ reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
+
+ if (onoff)
+ /* Turn off phy power saving */
+ reg1 &= ~phy_power[port];
+ else
+ reg1 |= phy_power[port];
+
+ sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
+ sky2_pci_read32(hw, PCI_DEV_REG1);
+ udelay(100);
+}
+
/* Force a renegotiation */
static void sky2_phy_reinit(struct sky2_port *sky2)
{
@@ -760,9 +767,10 @@
/* Update chip's next pointer */
static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx)
{
+ q = Y2_QADDR(q, PREF_UNIT_PUT_IDX);
wmb();
- sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx);
- mmiowb();
+ sky2_write16(hw, q, idx);
+ sky2_read16(hw, q);
}
@@ -949,14 +957,16 @@
/*
* It appears the hardware has a bug in the FIFO logic that
* cause it to hang if the FIFO gets overrun and the receive buffer
- * is not aligned. ALso alloc_skb() won't align properly if slab
- * debugging is enabled.
+ * is not 64 byte aligned. The buffer returned from netdev_alloc_skb is
+ * aligned except if slab debugging is enabled.
*/
-static inline struct sk_buff *sky2_alloc_skb(unsigned int size, gfp_t gfp_mask)
+static inline struct sk_buff *sky2_alloc_skb(struct net_device *dev,
+ unsigned int length,
+ gfp_t gfp_mask)
{
struct sk_buff *skb;
- skb = alloc_skb(size + RX_SKB_ALIGN, gfp_mask);
+ skb = __netdev_alloc_skb(dev, length + RX_SKB_ALIGN, gfp_mask);
if (likely(skb)) {
unsigned long p = (unsigned long) skb->data;
skb_reserve(skb, ALIGN(p, RX_SKB_ALIGN) - p);
@@ -992,7 +1002,8 @@
for (i = 0; i < sky2->rx_pending; i++) {
struct ring_info *re = sky2->rx_ring + i;
- re->skb = sky2_alloc_skb(sky2->rx_bufsize, GFP_KERNEL);
+ re->skb = sky2_alloc_skb(sky2->netdev, sky2->rx_bufsize,
+ GFP_KERNEL);
if (!re->skb)
goto nomem;
@@ -1080,6 +1091,8 @@
if (!sky2->rx_ring)
goto err_out;
+ sky2_phy_power(hw, port, 1);
+
sky2_mac_init(hw, port);
/* Determine available ram buffer space (in 4K blocks).
@@ -1184,7 +1197,6 @@
struct sky2_tx_le *le = NULL;
struct tx_ring_info *re;
unsigned i, len;
- int avail;
dma_addr_t mapping;
u32 addr64;
u16 mss;
@@ -1234,25 +1246,18 @@
/* Check for TCP Segmentation Offload */
mss = skb_shinfo(skb)->gso_size;
if (mss != 0) {
- /* just drop the packet if non-linear expansion fails */
- if (skb_header_cloned(skb) &&
- pskb_expand_head(skb, 0, 0, GFP_ATOMIC)) {
- dev_kfree_skb(skb);
- goto out_unlock;
- }
-
mss += ((skb->h.th->doff - 5) * 4); /* TCP options */
mss += (skb->nh.iph->ihl * 4) + sizeof(struct tcphdr);
mss += ETH_HLEN;
- }
- if (mss != sky2->tx_last_mss) {
- le = get_tx_le(sky2);
- le->tx.tso.size = cpu_to_le16(mss);
- le->tx.tso.rsvd = 0;
- le->opcode = OP_LRGLEN | HW_OWNER;
- le->ctrl = 0;
- sky2->tx_last_mss = mss;
+ if (mss != sky2->tx_last_mss) {
+ le = get_tx_le(sky2);
+ le->tx.tso.size = cpu_to_le16(mss);
+ le->tx.tso.rsvd = 0;
+ le->opcode = OP_LRGLEN | HW_OWNER;
+ le->ctrl = 0;
+ sky2->tx_last_mss = mss;
+ }
}
ctrl = 0;
@@ -1280,12 +1285,17 @@
if (skb->nh.iph->protocol == IPPROTO_UDP)
ctrl |= UDPTCP;
- le = get_tx_le(sky2);
- le->tx.csum.start = cpu_to_le16(hdr);
- le->tx.csum.offset = cpu_to_le16(offset);
- le->length = 0; /* initial checksum value */
- le->ctrl = 1; /* one packet */
- le->opcode = OP_TCPLISW | HW_OWNER;
+ if (hdr != sky2->tx_csum_start || offset != sky2->tx_csum_offset) {
+ sky2->tx_csum_start = hdr;
+ sky2->tx_csum_offset = offset;
+
+ le = get_tx_le(sky2);
+ le->tx.csum.start = cpu_to_le16(hdr);
+ le->tx.csum.offset = cpu_to_le16(offset);
+ le->length = 0; /* initial checksum value */
+ le->ctrl = 1; /* one packet */
+ le->opcode = OP_TCPLISW | HW_OWNER;
+ }
}
le = get_tx_le(sky2);
@@ -1320,23 +1330,18 @@
le->opcode = OP_BUFFER | HW_OWNER;
fre = sky2->tx_ring
- + RING_NEXT((re - sky2->tx_ring) + i, TX_RING_SIZE);
+ + RING_NEXT((re - sky2->tx_ring) + i, TX_RING_SIZE);
pci_unmap_addr_set(fre, mapaddr, mapping);
}
re->idx = sky2->tx_prod;
le->ctrl |= EOP;
- avail = tx_avail(sky2);
- if (mss != 0 || avail < TX_MIN_PENDING) {
- le->ctrl |= FRC_STAT;
- if (avail <= MAX_SKB_TX_LE)
- netif_stop_queue(dev);
- }
+ if (tx_avail(sky2) <= MAX_SKB_TX_LE)
+ netif_stop_queue(dev);
sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod);
-out_unlock:
spin_unlock(&sky2->tx_lock);
dev->trans_start = jiffies;
@@ -1421,7 +1426,7 @@
/* Stop more packets from being queued */
netif_stop_queue(dev);
- sky2_phy_reset(hw, port);
+ sky2_gmac_reset(hw, port);
/* Stop transmitter */
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP);
@@ -1469,6 +1474,8 @@
imask &= ~portirq_msk[port];
sky2_write32(hw, B0_IMSK, imask);
+ sky2_phy_power(hw, port, 0);
+
/* turn off LED's */
sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
@@ -1832,15 +1839,16 @@
* For small packets or errors, just reuse existing skb.
* For larger packets, get new buffer.
*/
-static struct sk_buff *sky2_receive(struct sky2_port *sky2,
+static struct sk_buff *sky2_receive(struct net_device *dev,
u16 length, u32 status)
{
+ struct sky2_port *sky2 = netdev_priv(dev);
struct ring_info *re = sky2->rx_ring + sky2->rx_next;
struct sk_buff *skb = NULL;
if (unlikely(netif_msg_rx_status(sky2)))
printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n",
- sky2->netdev->name, sky2->rx_next, status, length);
+ dev->name, sky2->rx_next, status, length);
sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending;
prefetch(sky2->rx_ring + sky2->rx_next);
@@ -1851,11 +1859,11 @@
if (!(status & GMR_FS_RX_OK))
goto resubmit;
- if (length > sky2->netdev->mtu + ETH_HLEN)
+ if (length > dev->mtu + ETH_HLEN)
goto oversize;
if (length < copybreak) {
- skb = alloc_skb(length + 2, GFP_ATOMIC);
+ skb = netdev_alloc_skb(dev, length + 2);
if (!skb)
goto resubmit;
@@ -1870,7 +1878,7 @@
} else {
struct sk_buff *nskb;
- nskb = sky2_alloc_skb(sky2->rx_bufsize, GFP_ATOMIC);
+ nskb = sky2_alloc_skb(dev, sky2->rx_bufsize, GFP_ATOMIC);
if (!nskb)
goto resubmit;
@@ -1900,7 +1908,7 @@
if (netif_msg_rx_err(sky2) && net_ratelimit())
printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
- sky2->netdev->name, status, length);
+ dev->name, status, length);
if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE))
sky2->net_stats.rx_length_errors++;
@@ -1926,12 +1934,6 @@
}
}
-/* Is status ring empty or is there more to do? */
-static inline int sky2_more_work(const struct sky2_hw *hw)
-{
- return (hw->st_idx != sky2_read16(hw, STAT_PUT_IDX));
-}
-
/* Process status response ring */
static int sky2_status_intr(struct sky2_hw *hw, int to_do)
{
@@ -1960,11 +1962,10 @@
switch (le->opcode & ~HW_OWNER) {
case OP_RXSTAT:
- skb = sky2_receive(sky2, length, status);
+ skb = sky2_receive(dev, length, status);
if (!skb)
break;
- skb->dev = dev;
skb->protocol = eth_type_trans(skb, dev);
dev->last_rx = jiffies;
@@ -2022,6 +2023,9 @@
}
}
+ /* Fully processed status ring so clear irq */
+ sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
+
exit_loop:
if (buf_write[0]) {
sky2 = netdev_priv(hw->dev[0]);
@@ -2231,19 +2235,16 @@
sky2_descriptor_error(hw, 1, "transmit", Y2_IS_CHK_TXA2);
work_done = sky2_status_intr(hw, work_limit);
- *budget -= work_done;
- dev0->quota -= work_done;
+ if (work_done < work_limit) {
+ netif_rx_complete(dev0);
- if (status & Y2_IS_STAT_BMU)
- sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ);
-
- if (sky2_more_work(hw))
+ sky2_read32(hw, B0_Y2_SP_LISR);
+ return 0;
+ } else {
+ *budget -= work_done;
+ dev0->quota -= work_done;
return 1;
-
- netif_rx_complete(dev0);
-
- sky2_read32(hw, B0_Y2_SP_LISR);
- return 0;
+ }
}
static irqreturn_t sky2_intr(int irq, void *dev_id, struct pt_regs *regs)
@@ -2409,7 +2410,7 @@
sky2_write32(hw, B0_HWE_IMSK, Y2_HWE_ALL_MASK);
for (i = 0; i < hw->ports; i++)
- sky2_phy_reset(hw, i);
+ sky2_gmac_reset(hw, i);
memset(hw->st_le, 0, STATUS_LE_BYTES);
hw->st_idx = 0;
@@ -3200,6 +3201,8 @@
struct pci_dev *pdev = hw->pdev;
int err;
+ init_waitqueue_head (&hw->msi_wait);
+
sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW);
err = request_irq(pdev->irq, sky2_test_intr, IRQF_SHARED, DRV_NAME, hw);
@@ -3209,10 +3212,8 @@
return err;
}
- init_waitqueue_head (&hw->msi_wait);
-
sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ);
- wmb();
+ sky2_read8(hw, B0_CTST);
wait_event_timeout(hw->msi_wait, hw->msi_detected, HZ/10);
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index 2db8d19..fa8af9f 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -1748,7 +1748,6 @@
INIT_SUM= 1<<3,
LOCK_SUM= 1<<4,
INS_VLAN= 1<<5,
- FRC_STAT= 1<<6,
EOP = 1<<7,
};
@@ -1844,6 +1843,8 @@
u32 tx_addr64;
u16 tx_pending;
u16 tx_last_mss;
+ u16 tx_csum_start;
+ u16 tx_csum_offset;
struct ring_info *rx_ring ____cacheline_aligned_in_smp;
struct sky2_rx_le *rx_le;
diff --git a/drivers/net/slhc.c b/drivers/net/slhc.c
index 3a1b713..9a540e2 100644
--- a/drivers/net/slhc.c
+++ b/drivers/net/slhc.c
@@ -94,27 +94,23 @@
register struct cstate *ts;
struct slcompress *comp;
- comp = (struct slcompress *)kmalloc(sizeof(struct slcompress),
- GFP_KERNEL);
+ comp = kzalloc(sizeof(struct slcompress), GFP_KERNEL);
if (! comp)
goto out_fail;
- memset(comp, 0, sizeof(struct slcompress));
if ( rslots > 0 && rslots < 256 ) {
size_t rsize = rslots * sizeof(struct cstate);
- comp->rstate = (struct cstate *) kmalloc(rsize, GFP_KERNEL);
+ comp->rstate = kzalloc(rsize, GFP_KERNEL);
if (! comp->rstate)
goto out_free;
- memset(comp->rstate, 0, rsize);
comp->rslot_limit = rslots - 1;
}
if ( tslots > 0 && tslots < 256 ) {
size_t tsize = tslots * sizeof(struct cstate);
- comp->tstate = (struct cstate *) kmalloc(tsize, GFP_KERNEL);
+ comp->tstate = kzalloc(tsize, GFP_KERNEL);
if (! comp->tstate)
goto out_free2;
- memset(comp->tstate, 0, tsize);
comp->tslot_limit = tslots - 1;
}
@@ -141,9 +137,9 @@
return comp;
out_free2:
- kfree((unsigned char *)comp->rstate);
+ kfree(comp->rstate);
out_free:
- kfree((unsigned char *)comp);
+ kfree(comp);
out_fail:
return NULL;
}
@@ -700,20 +696,6 @@
EXPORT_SYMBOL(slhc_uncompress);
EXPORT_SYMBOL(slhc_toss);
-#ifdef MODULE
-
-int init_module(void)
-{
- printk(KERN_INFO "CSLIP: code copyright 1989 Regents of the University of California\n");
- return 0;
-}
-
-void cleanup_module(void)
-{
- return;
-}
-
-#endif /* MODULE */
#else /* CONFIG_INET */
diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c
index 0b15290..4438fe8 100644
--- a/drivers/net/smc911x.c
+++ b/drivers/net/smc911x.c
@@ -55,8 +55,6 @@
)
#endif
-
-#include <linux/config.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/kernel.h>
diff --git a/drivers/net/starfire.c b/drivers/net/starfire.c
index c0a62b0..8e1f620 100644
--- a/drivers/net/starfire.c
+++ b/drivers/net/starfire.c
@@ -2053,7 +2053,7 @@
return -ENODEV;
}
- return pci_module_init (&starfire_driver);
+ return pci_register_driver(&starfire_driver);
}
diff --git a/drivers/net/sundance.c b/drivers/net/sundance.c
index 698568e..c243a80 100644
--- a/drivers/net/sundance.c
+++ b/drivers/net/sundance.c
@@ -17,6 +17,8 @@
Support and updates available at
http://www.scyld.com/network/sundance.html
[link no longer provides useful info -jgarzik]
+ Archives of the mailing list are still available at
+ http://www.beowulf.org/pipermail/netdrivers/
*/
@@ -646,7 +648,7 @@
/* Reset the chip to erase previous misconfiguration. */
if (netif_msg_hw(np))
printk("ASIC Control is %x.\n", ioread32(ioaddr + ASICCtrl));
- iowrite16(0x00ff, ioaddr + ASICCtrl + 2);
+ sundance_reset(dev, 0x00ff << 16);
if (netif_msg_hw(np))
printk("ASIC Control is now %x.\n", ioread32(ioaddr + ASICCtrl));
@@ -1075,13 +1077,8 @@
/* Reset tx logic, TxListPtr will be cleaned */
iowrite16 (TxDisable, ioaddr + MACCtrl1);
- iowrite16 (TxReset | DMAReset | FIFOReset | NetworkReset,
- ioaddr + ASICCtrl + 2);
- for (i=50; i > 0; i--) {
- if ((ioread16(ioaddr + ASICCtrl + 2) & ResetBusy) == 0)
- break;
- mdelay(1);
- }
+ sundance_reset(dev, (NetworkReset|FIFOReset|DMAReset|TxReset) << 16);
+
/* free all tx skbuff */
for (i = 0; i < TX_RING_SIZE; i++) {
skb = np->tx_skbuff[i];
@@ -1736,7 +1733,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init(&sundance_driver);
+ return pci_register_driver(&sundance_driver);
}
static void __exit sundance_exit(void)
diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c
index b70bbd7..1a441a8 100644
--- a/drivers/net/sungem.c
+++ b/drivers/net/sungem.c
@@ -3194,7 +3194,7 @@
static int __init gem_init(void)
{
- return pci_module_init(&gem_driver);
+ return pci_register_driver(&gem_driver);
}
static void __exit gem_cleanup(void)
diff --git a/drivers/net/tc35815.c b/drivers/net/tc35815.c
index 8b53ded..39460fa 100644
--- a/drivers/net/tc35815.c
+++ b/drivers/net/tc35815.c
@@ -1725,7 +1725,7 @@
static int __init tc35815_init_module(void)
{
- return pci_module_init(&tc35815_driver);
+ return pci_register_driver(&tc35815_driver);
}
static void __exit tc35815_cleanup_module(void)
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index eafabb2..d6e2a68 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -11819,7 +11819,7 @@
static int __init tg3_init(void)
{
- return pci_module_init(&tg3_driver);
+ return pci_register_driver(&tg3_driver);
}
static void __exit tg3_cleanup(void)
diff --git a/drivers/net/tokenring/3c359.c b/drivers/net/tokenring/3c359.c
index 465921e..412390b 100644
--- a/drivers/net/tokenring/3c359.c
+++ b/drivers/net/tokenring/3c359.c
@@ -1815,7 +1815,7 @@
static int __init xl_pci_init (void)
{
- return pci_module_init (&xl_3c359_driver);
+ return pci_register_driver(&xl_3c359_driver);
}
diff --git a/drivers/net/tokenring/lanstreamer.c b/drivers/net/tokenring/lanstreamer.c
index 28d968f..0d66700 100644
--- a/drivers/net/tokenring/lanstreamer.c
+++ b/drivers/net/tokenring/lanstreamer.c
@@ -1998,7 +1998,7 @@
};
static int __init streamer_init_module(void) {
- return pci_module_init(&streamer_pci_driver);
+ return pci_register_driver(&streamer_pci_driver);
}
static void __exit streamer_cleanup_module(void) {
diff --git a/drivers/net/tulip/de2104x.c b/drivers/net/tulip/de2104x.c
index d05c5aa..350a73e 100644
--- a/drivers/net/tulip/de2104x.c
+++ b/drivers/net/tulip/de2104x.c
@@ -2172,7 +2172,7 @@
#ifdef MODULE
printk("%s", version);
#endif
- return pci_module_init (&de_driver);
+ return pci_register_driver(&de_driver);
}
static void __exit de_exit (void)
diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/tulip/de4x5.c
index 75ff14a..e661d0a 100644
--- a/drivers/net/tulip/de4x5.c
+++ b/drivers/net/tulip/de4x5.c
@@ -5754,7 +5754,7 @@
int err = 0;
#ifdef CONFIG_PCI
- err = pci_module_init (&de4x5_pci_driver);
+ err = pci_register_driver(&de4x5_pci_driver);
#endif
#ifdef CONFIG_EISA
err |= eisa_driver_register (&de4x5_eisa_driver);
diff --git a/drivers/net/tulip/dmfe.c b/drivers/net/tulip/dmfe.c
index 4e5b0f2..66dade5 100644
--- a/drivers/net/tulip/dmfe.c
+++ b/drivers/net/tulip/dmfe.c
@@ -2039,7 +2039,7 @@
if (HPNA_NoiseFloor > 15)
HPNA_NoiseFloor = 0;
- rc = pci_module_init(&dmfe_driver);
+ rc = pci_register_driver(&dmfe_driver);
if (rc < 0)
return rc;
diff --git a/drivers/net/tulip/tulip_core.c b/drivers/net/tulip/tulip_core.c
index 7351831..e1987ec 100644
--- a/drivers/net/tulip/tulip_core.c
+++ b/drivers/net/tulip/tulip_core.c
@@ -1849,7 +1849,7 @@
tulip_max_interrupt_work = max_interrupt_work;
/* probe for and init boards */
- return pci_module_init (&tulip_driver);
+ return pci_register_driver(&tulip_driver);
}
diff --git a/drivers/net/tulip/uli526x.c b/drivers/net/tulip/uli526x.c
index fd64b2b..c4c720e 100644
--- a/drivers/net/tulip/uli526x.c
+++ b/drivers/net/tulip/uli526x.c
@@ -1702,7 +1702,6 @@
static int __init uli526x_init_module(void)
{
- int rc;
printk(version);
printed_version = 1;
@@ -1714,22 +1713,19 @@
if (cr6set)
uli526x_cr6_user_set = cr6set;
- switch(mode) {
+ switch (mode) {
case ULI526X_10MHF:
case ULI526X_100MHF:
case ULI526X_10MFD:
case ULI526X_100MFD:
uli526x_media_mode = mode;
break;
- default:uli526x_media_mode = ULI526X_AUTO;
+ default:
+ uli526x_media_mode = ULI526X_AUTO;
break;
}
- rc = pci_module_init(&uli526x_driver);
- if (rc < 0)
- return rc;
-
- return 0;
+ return pci_register_driver(&uli526x_driver);
}
diff --git a/drivers/net/tulip/winbond-840.c b/drivers/net/tulip/winbond-840.c
index eba9083..6b82d14 100644
--- a/drivers/net/tulip/winbond-840.c
+++ b/drivers/net/tulip/winbond-840.c
@@ -1689,7 +1689,7 @@
static int __init w840_init(void)
{
printk(version);
- return pci_module_init(&w840_driver);
+ return pci_register_driver(&w840_driver);
}
static void __exit w840_exit(void)
diff --git a/drivers/net/tulip/xircom_tulip_cb.c b/drivers/net/tulip/xircom_tulip_cb.c
index 17ca7dc..d797b7b 100644
--- a/drivers/net/tulip/xircom_tulip_cb.c
+++ b/drivers/net/tulip/xircom_tulip_cb.c
@@ -1707,7 +1707,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init(&xircom_driver);
+ return pci_register_driver(&xircom_driver);
}
diff --git a/drivers/net/typhoon.c b/drivers/net/typhoon.c
index 4103c37..1014461 100644
--- a/drivers/net/typhoon.c
+++ b/drivers/net/typhoon.c
@@ -2660,7 +2660,7 @@
static int __init
typhoon_init(void)
{
- return pci_module_init(&typhoon_driver);
+ return pci_register_driver(&typhoon_driver);
}
static void __exit
diff --git a/drivers/net/via-rhine.c b/drivers/net/via-rhine.c
index ae97108..efeb10b 100644
--- a/drivers/net/via-rhine.c
+++ b/drivers/net/via-rhine.c
@@ -2005,7 +2005,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init(&rhine_driver);
+ return pci_register_driver(&rhine_driver);
}
diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c
index aa9cd92..e266db1 100644
--- a/drivers/net/via-velocity.c
+++ b/drivers/net/via-velocity.c
@@ -2250,7 +2250,7 @@
int ret;
velocity_register_notifier();
- ret = pci_module_init(&velocity_driver);
+ ret = pci_register_driver(&velocity_driver);
if (ret < 0)
velocity_unregister_notifier();
return ret;
diff --git a/drivers/net/via-velocity.h b/drivers/net/via-velocity.h
index 496c3d5..4665ef2 100644
--- a/drivers/net/via-velocity.h
+++ b/drivers/net/via-velocity.h
@@ -262,25 +262,6 @@
dma_addr_t skb_dma;
};
-/**
- * alloc_rd_info - allocate an rd info block
- *
- * Alocate and initialize a receive info structure used for keeping
- * track of kernel side information related to each receive
- * descriptor we are using
- */
-
-static inline struct velocity_rd_info *alloc_rd_info(void)
-{
- struct velocity_rd_info *ptr;
- if ((ptr = kmalloc(sizeof(struct velocity_rd_info), GFP_ATOMIC)) == NULL)
- return NULL;
- else {
- memset(ptr, 0, sizeof(struct velocity_rd_info));
- return ptr;
- }
-}
-
/*
* Used to track transmit side buffers.
*/
diff --git a/drivers/net/wan/cycx_main.c b/drivers/net/wan/cycx_main.c
index 430b1f6..a5e7ce1 100644
--- a/drivers/net/wan/cycx_main.c
+++ b/drivers/net/wan/cycx_main.c
@@ -40,7 +40,6 @@
* 1998/08/08 acme Initial version.
*/
-#include <linux/config.h> /* OS configuration options */
#include <linux/stddef.h> /* offsetof(), etc. */
#include <linux/errno.h> /* return codes */
#include <linux/string.h> /* inline memset(), etc. */
diff --git a/drivers/net/wan/dlci.c b/drivers/net/wan/dlci.c
index 6e1ec5b..7369875 100644
--- a/drivers/net/wan/dlci.c
+++ b/drivers/net/wan/dlci.c
@@ -28,7 +28,6 @@
* 2 of the License, or (at your option) any later version.
*/
-#include <linux/config.h> /* for CONFIG_DLCI_COUNT */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
diff --git a/drivers/net/wan/dscc4.c b/drivers/net/wan/dscc4.c
index 684af43..af4d415 100644
--- a/drivers/net/wan/dscc4.c
+++ b/drivers/net/wan/dscc4.c
@@ -2062,7 +2062,7 @@
static int __init dscc4_init_module(void)
{
- return pci_module_init(&dscc4_driver);
+ return pci_register_driver(&dscc4_driver);
}
static void __exit dscc4_cleanup_module(void)
diff --git a/drivers/net/wan/farsync.c b/drivers/net/wan/farsync.c
index 3705db04a..564351a 100644
--- a/drivers/net/wan/farsync.c
+++ b/drivers/net/wan/farsync.c
@@ -2697,7 +2697,7 @@
for (i = 0; i < FST_MAX_CARDS; i++)
fst_card_array[i] = NULL;
spin_lock_init(&fst_work_q_lock);
- return pci_module_init(&fst_driver);
+ return pci_register_driver(&fst_driver);
}
static void __exit
diff --git a/drivers/net/wan/lmc/lmc_main.c b/drivers/net/wan/lmc/lmc_main.c
index 39f4424..7b5d81d 100644
--- a/drivers/net/wan/lmc/lmc_main.c
+++ b/drivers/net/wan/lmc/lmc_main.c
@@ -1790,7 +1790,7 @@
static int __init init_lmc(void)
{
- return pci_module_init(&lmc_driver);
+ return pci_register_driver(&lmc_driver);
}
static void __exit exit_lmc(void)
diff --git a/drivers/net/wan/pc300_drv.c b/drivers/net/wan/pc300_drv.c
index 567efff..56e6940 100644
--- a/drivers/net/wan/pc300_drv.c
+++ b/drivers/net/wan/pc300_drv.c
@@ -3677,7 +3677,7 @@
static int __init cpc_init(void)
{
- return pci_module_init(&cpc_driver);
+ return pci_register_driver(&cpc_driver);
}
static void __exit cpc_cleanup_module(void)
diff --git a/drivers/net/wan/pci200syn.c b/drivers/net/wan/pci200syn.c
index 4df61fa..a6b9c33 100644
--- a/drivers/net/wan/pci200syn.c
+++ b/drivers/net/wan/pci200syn.c
@@ -476,7 +476,7 @@
printk(KERN_ERR "pci200syn: Invalid PCI clock frequency\n");
return -EINVAL;
}
- return pci_module_init(&pci200_pci_driver);
+ return pci_register_driver(&pci200_pci_driver);
}
diff --git a/drivers/net/wan/sdla.c b/drivers/net/wan/sdla.c
index 7628c2d..0ba018f 100644
--- a/drivers/net/wan/sdla.c
+++ b/drivers/net/wan/sdla.c
@@ -32,7 +32,6 @@
* 2 of the License, or (at your option) any later version.
*/
-#include <linux/config.h> /* for CONFIG_DLCI_MAX */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/types.h>
diff --git a/drivers/net/wan/wanxl.c b/drivers/net/wan/wanxl.c
index b2031df..ec68f7d 100644
--- a/drivers/net/wan/wanxl.c
+++ b/drivers/net/wan/wanxl.c
@@ -837,7 +837,7 @@
#ifdef MODULE
printk(KERN_INFO "%s\n", version);
#endif
- return pci_module_init(&wanxl_pci_driver);
+ return pci_register_driver(&wanxl_pci_driver);
}
static void __exit wanxl_cleanup_module(void)
diff --git a/drivers/net/wireless/airo.c b/drivers/net/wireless/airo.c
index a4dd139..16befbce 100644
--- a/drivers/net/wireless/airo.c
+++ b/drivers/net/wireless/airo.c
@@ -3950,13 +3950,11 @@
pRsp->rsp0 = IN4500(ai, RESP0);
pRsp->rsp1 = IN4500(ai, RESP1);
pRsp->rsp2 = IN4500(ai, RESP2);
- if ((pRsp->status & 0xff00)!=0 && pCmd->cmd != CMD_SOFTRESET) {
- airo_print_err(ai->dev->name, "cmd= %x\n", pCmd->cmd);
- airo_print_err(ai->dev->name, "status= %x\n", pRsp->status);
- airo_print_err(ai->dev->name, "Rsp0= %x\n", pRsp->rsp0);
- airo_print_err(ai->dev->name, "Rsp1= %x\n", pRsp->rsp1);
- airo_print_err(ai->dev->name, "Rsp2= %x\n", pRsp->rsp2);
- }
+ if ((pRsp->status & 0xff00)!=0 && pCmd->cmd != CMD_SOFTRESET)
+ airo_print_err(ai->dev->name,
+ "cmd:%x status:%x rsp0:%x rsp1:%x rsp2:%x",
+ pCmd->cmd, pRsp->status, pRsp->rsp0, pRsp->rsp1,
+ pRsp->rsp2);
// clear stuck command busy if necessary
if (IN4500(ai, COMMAND) & COMMAND_BUSY) {
diff --git a/drivers/net/wireless/atmel_pci.c b/drivers/net/wireless/atmel_pci.c
index d425c3c..3bfa791 100644
--- a/drivers/net/wireless/atmel_pci.c
+++ b/drivers/net/wireless/atmel_pci.c
@@ -76,7 +76,7 @@
static int __init atmel_init_module(void)
{
- return pci_module_init(&atmel_driver);
+ return pci_register_driver(&atmel_driver);
}
static void __exit atmel_cleanup_module(void)
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx.h b/drivers/net/wireless/bcm43xx/bcm43xx.h
index 17a5682..c6ee1e9 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx.h
+++ b/drivers/net/wireless/bcm43xx/bcm43xx.h
@@ -504,6 +504,12 @@
* This lock is only used by bcm43xx_phy_{un}lock()
*/
spinlock_t lock;
+
+ /* Firmware. */
+ const struct firmware *ucode;
+ const struct firmware *pcm;
+ const struct firmware *initvals0;
+ const struct firmware *initvals1;
};
@@ -593,12 +599,14 @@
u8 available:1,
enabled:1,
initialized:1;
- /** core_id ID number */
- u16 id;
/** core_rev revision number */
u8 rev;
/** Index number for _switch_core() */
u8 index;
+ /** core_id ID number */
+ u16 id;
+ /** Core-specific data. */
+ void *priv;
};
/* Additional information for each 80211 core. */
@@ -647,7 +655,23 @@
BCM43xx_STAT_RESTARTING, /* controller_restart() called. */
};
#define bcm43xx_status(bcm) atomic_read(&(bcm)->init_status)
-#define bcm43xx_set_status(bcm, stat) atomic_set(&(bcm)->init_status, (stat))
+#define bcm43xx_set_status(bcm, stat) do { \
+ atomic_set(&(bcm)->init_status, (stat)); \
+ smp_wmb(); \
+ } while (0)
+
+/* *** THEORY OF LOCKING ***
+ *
+ * We have two different locks in the bcm43xx driver.
+ * => bcm->mutex: General sleeping mutex. Protects struct bcm43xx_private
+ * and the device registers. This mutex does _not_ protect
+ * against concurrency from the IRQ handler.
+ * => bcm->irq_lock: IRQ spinlock. Protects against IRQ handler concurrency.
+ *
+ * Please note that, if you only take the irq_lock, you are not protected
+ * against concurrency from the periodic work handlers.
+ * Most times you want to take _both_ locks.
+ */
struct bcm43xx_private {
struct ieee80211_device *ieee;
@@ -659,7 +683,6 @@
void __iomem *mmio_addr;
- /* Locking, see "theory of locking" text below. */
spinlock_t irq_lock;
struct mutex mutex;
@@ -691,6 +714,7 @@
struct bcm43xx_sprominfo sprom;
#define BCM43xx_NR_LEDS 4
struct bcm43xx_led leds[BCM43xx_NR_LEDS];
+ spinlock_t leds_lock;
/* The currently active core. */
struct bcm43xx_coreinfo *current_core;
@@ -708,10 +732,6 @@
struct bcm43xx_coreinfo core_80211[ BCM43xx_MAX_80211_CORES ];
/* Additional information, specific to the 80211 cores. */
struct bcm43xx_coreinfo_80211 core_80211_ext[ BCM43xx_MAX_80211_CORES ];
- /* Index of the current 80211 core. If current_core is not
- * an 80211 core, this is -1.
- */
- int current_80211_core_idx;
/* Number of available 80211 cores. */
int nr_80211_available;
@@ -724,6 +744,8 @@
u32 irq_savedstate;
/* Link Quality calculation context. */
struct bcm43xx_noise_calculation noisecalc;
+ /* if > 0 MAC is suspended. if == 0 MAC is enabled. */
+ int mac_suspended;
/* Threshold values. */
//TODO: The RTS thr has to be _used_. Currently, it is only set via WX.
@@ -746,12 +768,6 @@
struct bcm43xx_key key[54];
u8 default_key_idx;
- /* Firmware. */
- const struct firmware *ucode;
- const struct firmware *pcm;
- const struct firmware *initvals0;
- const struct firmware *initvals1;
-
/* Random Number Generator. */
struct hwrng rng;
char rng_name[20 + 1];
@@ -763,55 +779,6 @@
};
-/* *** THEORY OF LOCKING ***
- *
- * We have two different locks in the bcm43xx driver.
- * => bcm->mutex: General sleeping mutex. Protects struct bcm43xx_private
- * and the device registers.
- * => bcm->irq_lock: IRQ spinlock. Protects against IRQ handler concurrency.
- *
- * We have three types of helper function pairs to utilize these locks.
- * (Always use the helper functions.)
- * 1) bcm43xx_{un}lock_noirq():
- * Takes bcm->mutex. Does _not_ protect against IRQ concurrency,
- * so it is almost always unsafe, if device IRQs are enabled.
- * So only use this, if device IRQs are masked.
- * Locking may sleep.
- * You can sleep within the critical section.
- * 2) bcm43xx_{un}lock_irqonly():
- * Takes bcm->irq_lock. Does _not_ protect against
- * bcm43xx_lock_noirq() critical sections.
- * Does only protect against the IRQ handler path and other
- * irqonly() critical sections.
- * Locking does not sleep.
- * You must not sleep within the critical section.
- * 3) bcm43xx_{un}lock_irqsafe():
- * This is the cummulative lock and takes both, mutex and irq_lock.
- * Protects against noirq() and irqonly() critical sections (and
- * the IRQ handler path).
- * Locking may sleep.
- * You must not sleep within the critical section.
- */
-
-/* Lock type 1 */
-#define bcm43xx_lock_noirq(bcm) mutex_lock(&(bcm)->mutex)
-#define bcm43xx_unlock_noirq(bcm) mutex_unlock(&(bcm)->mutex)
-/* Lock type 2 */
-#define bcm43xx_lock_irqonly(bcm, flags) \
- spin_lock_irqsave(&(bcm)->irq_lock, flags)
-#define bcm43xx_unlock_irqonly(bcm, flags) \
- spin_unlock_irqrestore(&(bcm)->irq_lock, flags)
-/* Lock type 3 */
-#define bcm43xx_lock_irqsafe(bcm, flags) do { \
- bcm43xx_lock_noirq(bcm); \
- bcm43xx_lock_irqonly(bcm, flags); \
- } while (0)
-#define bcm43xx_unlock_irqsafe(bcm, flags) do { \
- bcm43xx_unlock_irqonly(bcm, flags); \
- bcm43xx_unlock_noirq(bcm); \
- } while (0)
-
-
static inline
struct bcm43xx_private * bcm43xx_priv(struct net_device *dev)
{
@@ -863,34 +830,33 @@
* any of these functions.
*/
static inline
+struct bcm43xx_coreinfo_80211 *
+bcm43xx_current_80211_priv(struct bcm43xx_private *bcm)
+{
+ assert(bcm->current_core->id == BCM43xx_COREID_80211);
+ return bcm->current_core->priv;
+}
+static inline
struct bcm43xx_pio * bcm43xx_current_pio(struct bcm43xx_private *bcm)
{
assert(bcm43xx_using_pio(bcm));
- assert(bcm->current_80211_core_idx >= 0);
- assert(bcm->current_80211_core_idx < BCM43xx_MAX_80211_CORES);
- return &(bcm->core_80211_ext[bcm->current_80211_core_idx].pio);
+ return &(bcm43xx_current_80211_priv(bcm)->pio);
}
static inline
struct bcm43xx_dma * bcm43xx_current_dma(struct bcm43xx_private *bcm)
{
assert(!bcm43xx_using_pio(bcm));
- assert(bcm->current_80211_core_idx >= 0);
- assert(bcm->current_80211_core_idx < BCM43xx_MAX_80211_CORES);
- return &(bcm->core_80211_ext[bcm->current_80211_core_idx].dma);
+ return &(bcm43xx_current_80211_priv(bcm)->dma);
}
static inline
struct bcm43xx_phyinfo * bcm43xx_current_phy(struct bcm43xx_private *bcm)
{
- assert(bcm->current_80211_core_idx >= 0);
- assert(bcm->current_80211_core_idx < BCM43xx_MAX_80211_CORES);
- return &(bcm->core_80211_ext[bcm->current_80211_core_idx].phy);
+ return &(bcm43xx_current_80211_priv(bcm)->phy);
}
static inline
struct bcm43xx_radioinfo * bcm43xx_current_radio(struct bcm43xx_private *bcm)
{
- assert(bcm->current_80211_core_idx >= 0);
- assert(bcm->current_80211_core_idx < BCM43xx_MAX_80211_CORES);
- return &(bcm->core_80211_ext[bcm->current_80211_core_idx].radio);
+ return &(bcm43xx_current_80211_priv(bcm)->radio);
}
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
index ce2e40b..923275e 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c
@@ -77,7 +77,8 @@
down(&big_buffer_sem);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED) {
fappend("Board not initialized.\n");
goto out;
@@ -121,7 +122,8 @@
fappend("\n");
out:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
res = simple_read_from_buffer(userbuf, count, ppos, buf, pos);
up(&big_buffer_sem);
return res;
@@ -159,7 +161,8 @@
unsigned long flags;
down(&big_buffer_sem);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED) {
fappend("Board not initialized.\n");
goto out;
@@ -169,7 +172,8 @@
fappend("boardflags: 0x%04x\n", bcm->sprom.boardflags);
out:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
res = simple_read_from_buffer(userbuf, count, ppos, buf, pos);
up(&big_buffer_sem);
return res;
@@ -188,7 +192,8 @@
u64 tsf;
down(&big_buffer_sem);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED) {
fappend("Board not initialized.\n");
goto out;
@@ -199,7 +204,8 @@
(unsigned int)(tsf & 0xFFFFFFFFULL));
out:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
res = simple_read_from_buffer(userbuf, count, ppos, buf, pos);
up(&big_buffer_sem);
return res;
@@ -221,7 +227,8 @@
res = -EFAULT;
goto out_up;
}
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED) {
printk(KERN_INFO PFX "debugfs: Board not initialized.\n");
res = -EFAULT;
@@ -237,7 +244,8 @@
res = buf_size;
out_unlock:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
out_up:
up(&big_buffer_sem);
return res;
@@ -258,7 +266,8 @@
int i, cnt, j = 0;
down(&big_buffer_sem);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
fappend("Last %d logged xmitstatus blobs (Latest first):\n\n",
BCM43xx_NR_LOGGED_XMITSTATUS);
@@ -294,14 +303,51 @@
i = BCM43xx_NR_LOGGED_XMITSTATUS - 1;
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
res = simple_read_from_buffer(userbuf, count, ppos, buf, pos);
- bcm43xx_lock_irqsafe(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (*ppos == pos) {
/* Done. Drop the copied data. */
e->xmitstatus_printing = 0;
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
+ up(&big_buffer_sem);
+ return res;
+}
+
+static ssize_t restart_write_file(struct file *file, const char __user *user_buf,
+ size_t count, loff_t *ppos)
+{
+ struct bcm43xx_private *bcm = file->private_data;
+ char *buf = really_big_buffer;
+ ssize_t buf_size;
+ ssize_t res;
+ unsigned long flags;
+
+ buf_size = min(count, sizeof (really_big_buffer) - 1);
+ down(&big_buffer_sem);
+ if (copy_from_user(buf, user_buf, buf_size)) {
+ res = -EFAULT;
+ goto out_up;
+ }
+ mutex_lock(&(bcm)->mutex);
+ spin_lock_irqsave(&(bcm)->irq_lock, flags);
+ if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED) {
+ printk(KERN_INFO PFX "debugfs: Board not initialized.\n");
+ res = -EFAULT;
+ goto out_unlock;
+ }
+ if (count > 0 && buf[0] == '1') {
+ bcm43xx_controller_restart(bcm, "manually restarted");
+ res = count;
+ } else
+ res = -EINVAL;
+
+out_unlock:
+ spin_unlock_irqrestore(&(bcm)->irq_lock, flags);
+ mutex_unlock(&(bcm)->mutex);
+out_up:
up(&big_buffer_sem);
return res;
}
@@ -339,6 +385,11 @@
.open = open_file_generic,
};
+static struct file_operations restart_fops = {
+ .write = restart_write_file,
+ .open = open_file_generic,
+};
+
void bcm43xx_debugfs_add_device(struct bcm43xx_private *bcm)
{
@@ -390,6 +441,10 @@
bcm, &txstat_fops);
if (!e->dentry_txstat)
printk(KERN_ERR PFX "debugfs: creating \"tx_status\" for \"%s\" failed!\n", devdir);
+ e->dentry_restart = debugfs_create_file("restart", 0222, e->subdir,
+ bcm, &restart_fops);
+ if (!e->dentry_restart)
+ printk(KERN_ERR PFX "debugfs: creating \"restart\" for \"%s\" failed!\n", devdir);
}
void bcm43xx_debugfs_remove_device(struct bcm43xx_private *bcm)
@@ -405,6 +460,7 @@
debugfs_remove(e->dentry_devinfo);
debugfs_remove(e->dentry_tsf);
debugfs_remove(e->dentry_txstat);
+ debugfs_remove(e->dentry_restart);
debugfs_remove(e->subdir);
kfree(e->xmitstatus_buffer);
kfree(e->xmitstatus_print_buffer);
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.h b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.h
index 50ce267..a40d1af 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.h
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_debugfs.h
@@ -20,6 +20,7 @@
struct dentry *dentry_spromdump;
struct dentry *dentry_tsf;
struct dentry *dentry_txstat;
+ struct dentry *dentry_restart;
struct bcm43xx_private *bcm;
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_leds.c b/drivers/net/wireless/bcm43xx/bcm43xx_leds.c
index ec80692..c3f90c8 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_leds.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_leds.c
@@ -51,12 +51,12 @@
struct bcm43xx_private *bcm = led->bcm;
unsigned long flags;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->leds_lock, flags);
if (led->blink_interval) {
bcm43xx_led_changestate(led);
mod_timer(&led->blink_timer, jiffies + led->blink_interval);
}
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->leds_lock, flags);
}
static void bcm43xx_led_blink_start(struct bcm43xx_led *led,
@@ -177,7 +177,9 @@
int i, turn_on;
unsigned long interval = 0;
u16 ledctl;
+ unsigned long flags;
+ spin_lock_irqsave(&bcm->leds_lock, flags);
ledctl = bcm43xx_read16(bcm, BCM43xx_MMIO_GPIO_CONTROL);
for (i = 0; i < BCM43xx_NR_LEDS; i++) {
led = &(bcm->leds[i]);
@@ -266,6 +268,7 @@
ledctl &= ~(1 << i);
}
bcm43xx_write16(bcm, BCM43xx_MMIO_GPIO_CONTROL, ledctl);
+ spin_unlock_irqrestore(&bcm->leds_lock, flags);
}
void bcm43xx_leds_switch_all(struct bcm43xx_private *bcm, int on)
@@ -274,7 +277,9 @@
u16 ledctl;
int i;
int bit_on;
+ unsigned long flags;
+ spin_lock_irqsave(&bcm->leds_lock, flags);
ledctl = bcm43xx_read16(bcm, BCM43xx_MMIO_GPIO_CONTROL);
for (i = 0; i < BCM43xx_NR_LEDS; i++) {
led = &(bcm->leds[i]);
@@ -290,4 +295,5 @@
ledctl &= ~(1 << i);
}
bcm43xx_write16(bcm, BCM43xx_MMIO_GPIO_CONTROL, ledctl);
+ spin_unlock_irqrestore(&bcm->leds_lock, flags);
}
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_main.c b/drivers/net/wireless/bcm43xx/bcm43xx_main.c
index df317c1..b095f3c 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_main.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_main.c
@@ -509,23 +509,19 @@
}
/* Make sure we don't receive more data from the device. */
-static int bcm43xx_disable_interrupts_sync(struct bcm43xx_private *bcm, u32 *oldstate)
+static int bcm43xx_disable_interrupts_sync(struct bcm43xx_private *bcm)
{
unsigned long flags;
- u32 old;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (unlikely(bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED)) {
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
return -EBUSY;
}
- old = bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
- bcm43xx_unlock_irqonly(bcm, flags);
+ bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
bcm43xx_synchronize_irq(bcm);
- if (oldstate)
- *oldstate = old;
-
return 0;
}
@@ -537,7 +533,6 @@
u16 manufact;
u16 version;
u8 revision;
- s8 i;
if (bcm->chip_id == 0x4317) {
if (bcm->chip_rev == 0x00)
@@ -580,20 +575,11 @@
radio->version = version;
radio->revision = revision;
- /* Set default attenuation values. */
- radio->baseband_atten = bcm43xx_default_baseband_attenuation(bcm);
- radio->radio_atten = bcm43xx_default_radio_attenuation(bcm);
- radio->txctl1 = bcm43xx_default_txctl1(bcm);
- radio->txctl2 = 0xFFFF;
if (phy->type == BCM43xx_PHYTYPE_A)
radio->txpower_desired = bcm->sprom.maxpower_aphy;
else
radio->txpower_desired = bcm->sprom.maxpower_bgphy;
- /* Initialize the in-memory nrssi Lookup Table. */
- for (i = 0; i < 64; i++)
- radio->nrssi_lt[i] = i;
-
return 0;
err_unsupported_radio:
@@ -1250,10 +1236,6 @@
goto out;
bcm->current_core = new_core;
- bcm->current_80211_core_idx = -1;
- if (new_core->id == BCM43xx_COREID_80211)
- bcm->current_80211_core_idx = (int)(new_core - &(bcm->core_80211[0]));
-
out:
return err;
}
@@ -1423,43 +1405,23 @@
bcm43xx_core_disable(bcm, 0);
}
-/* Mark the current 80211 core inactive.
- * "active_80211_core" is the other 80211 core, which is used.
- */
-static int bcm43xx_wireless_core_mark_inactive(struct bcm43xx_private *bcm,
- struct bcm43xx_coreinfo *active_80211_core)
+/* Mark the current 80211 core inactive. */
+static void bcm43xx_wireless_core_mark_inactive(struct bcm43xx_private *bcm)
{
u32 sbtmstatelow;
- struct bcm43xx_coreinfo *old_core;
- int err = 0;
bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
bcm43xx_radio_turn_off(bcm);
sbtmstatelow = bcm43xx_read32(bcm, BCM43xx_CIR_SBTMSTATELOW);
- sbtmstatelow &= ~0x200a0000;
- sbtmstatelow |= 0xa0000;
+ sbtmstatelow &= 0xDFF5FFFF;
+ sbtmstatelow |= 0x000A0000;
bcm43xx_write32(bcm, BCM43xx_CIR_SBTMSTATELOW, sbtmstatelow);
udelay(1);
sbtmstatelow = bcm43xx_read32(bcm, BCM43xx_CIR_SBTMSTATELOW);
- sbtmstatelow &= ~0xa0000;
- sbtmstatelow |= 0x80000;
+ sbtmstatelow &= 0xFFF5FFFF;
+ sbtmstatelow |= 0x00080000;
bcm43xx_write32(bcm, BCM43xx_CIR_SBTMSTATELOW, sbtmstatelow);
udelay(1);
-
- if (bcm43xx_current_phy(bcm)->type == BCM43xx_PHYTYPE_G) {
- old_core = bcm->current_core;
- err = bcm43xx_switch_core(bcm, active_80211_core);
- if (err)
- goto out;
- sbtmstatelow = bcm43xx_read32(bcm, BCM43xx_CIR_SBTMSTATELOW);
- sbtmstatelow &= ~0x20000000;
- sbtmstatelow |= 0x20000000;
- bcm43xx_write32(bcm, BCM43xx_CIR_SBTMSTATELOW, sbtmstatelow);
- err = bcm43xx_switch_core(bcm, old_core);
- }
-
-out:
- return err;
}
static void handle_irq_transmit_status(struct bcm43xx_private *bcm)
@@ -1720,7 +1682,7 @@
# define bcmirq_handled(irq) do { /* nothing */ } while (0)
#endif /* CONFIG_BCM43XX_DEBUG*/
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
reason = bcm->irq_reason;
dma_reason[0] = bcm->dma_reason[0];
dma_reason[1] = bcm->dma_reason[1];
@@ -1746,7 +1708,7 @@
dma_reason[2], dma_reason[3]);
bcm43xx_controller_restart(bcm, "DMA error");
mmiowb();
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
return;
}
if (unlikely((dma_reason[0] & BCM43xx_DMAIRQ_NONFATALMASK) |
@@ -1834,7 +1796,7 @@
bcm43xx_leds_update(bcm, activity);
bcm43xx_interrupt_enable(bcm, bcm->irq_savedstate);
mmiowb();
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
}
static void pio_irq_workaround(struct bcm43xx_private *bcm,
@@ -1885,14 +1847,8 @@
spin_lock(&bcm->irq_lock);
- /* Only accept IRQs, if we are initialized properly.
- * This avoids an RX race while initializing.
- * We should probably not enable IRQs before we are initialized
- * completely, but some careful work is needed to fix this. I think it
- * is best to stay with this cheap workaround for now... .
- */
- if (unlikely(bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED))
- goto out;
+ assert(bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED);
+ assert(bcm->current_core->id == BCM43xx_COREID_80211);
reason = bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
if (reason == 0xffffffff) {
@@ -1930,16 +1886,18 @@
static void bcm43xx_release_firmware(struct bcm43xx_private *bcm, int force)
{
+ struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
+
if (bcm->firmware_norelease && !force)
return; /* Suspending or controller reset. */
- release_firmware(bcm->ucode);
- bcm->ucode = NULL;
- release_firmware(bcm->pcm);
- bcm->pcm = NULL;
- release_firmware(bcm->initvals0);
- bcm->initvals0 = NULL;
- release_firmware(bcm->initvals1);
- bcm->initvals1 = NULL;
+ release_firmware(phy->ucode);
+ phy->ucode = NULL;
+ release_firmware(phy->pcm);
+ phy->pcm = NULL;
+ release_firmware(phy->initvals0);
+ phy->initvals0 = NULL;
+ release_firmware(phy->initvals1);
+ phy->initvals1 = NULL;
}
static int bcm43xx_request_firmware(struct bcm43xx_private *bcm)
@@ -1950,11 +1908,11 @@
int nr;
char buf[22 + sizeof(modparam_fwpostfix) - 1] = { 0 };
- if (!bcm->ucode) {
+ if (!phy->ucode) {
snprintf(buf, ARRAY_SIZE(buf), "bcm43xx_microcode%d%s.fw",
(rev >= 5 ? 5 : rev),
modparam_fwpostfix);
- err = request_firmware(&bcm->ucode, buf, &bcm->pci_dev->dev);
+ err = request_firmware(&phy->ucode, buf, &bcm->pci_dev->dev);
if (err) {
printk(KERN_ERR PFX
"Error: Microcode \"%s\" not available or load failed.\n",
@@ -1963,12 +1921,12 @@
}
}
- if (!bcm->pcm) {
+ if (!phy->pcm) {
snprintf(buf, ARRAY_SIZE(buf),
"bcm43xx_pcm%d%s.fw",
(rev < 5 ? 4 : 5),
modparam_fwpostfix);
- err = request_firmware(&bcm->pcm, buf, &bcm->pci_dev->dev);
+ err = request_firmware(&phy->pcm, buf, &bcm->pci_dev->dev);
if (err) {
printk(KERN_ERR PFX
"Error: PCM \"%s\" not available or load failed.\n",
@@ -1977,7 +1935,7 @@
}
}
- if (!bcm->initvals0) {
+ if (!phy->initvals0) {
if (rev == 2 || rev == 4) {
switch (phy->type) {
case BCM43xx_PHYTYPE_A:
@@ -2008,20 +1966,20 @@
snprintf(buf, ARRAY_SIZE(buf), "bcm43xx_initval%02d%s.fw",
nr, modparam_fwpostfix);
- err = request_firmware(&bcm->initvals0, buf, &bcm->pci_dev->dev);
+ err = request_firmware(&phy->initvals0, buf, &bcm->pci_dev->dev);
if (err) {
printk(KERN_ERR PFX
"Error: InitVals \"%s\" not available or load failed.\n",
buf);
goto error;
}
- if (bcm->initvals0->size % sizeof(struct bcm43xx_initval)) {
+ if (phy->initvals0->size % sizeof(struct bcm43xx_initval)) {
printk(KERN_ERR PFX "InitVals fileformat error.\n");
goto error;
}
}
- if (!bcm->initvals1) {
+ if (!phy->initvals1) {
if (rev >= 5) {
u32 sbtmstatehigh;
@@ -2043,14 +2001,14 @@
snprintf(buf, ARRAY_SIZE(buf), "bcm43xx_initval%02d%s.fw",
nr, modparam_fwpostfix);
- err = request_firmware(&bcm->initvals1, buf, &bcm->pci_dev->dev);
+ err = request_firmware(&phy->initvals1, buf, &bcm->pci_dev->dev);
if (err) {
printk(KERN_ERR PFX
"Error: InitVals \"%s\" not available or load failed.\n",
buf);
goto error;
}
- if (bcm->initvals1->size % sizeof(struct bcm43xx_initval)) {
+ if (phy->initvals1->size % sizeof(struct bcm43xx_initval)) {
printk(KERN_ERR PFX "InitVals fileformat error.\n");
goto error;
}
@@ -2070,12 +2028,13 @@
static void bcm43xx_upload_microcode(struct bcm43xx_private *bcm)
{
+ struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
const u32 *data;
unsigned int i, len;
/* Upload Microcode. */
- data = (u32 *)(bcm->ucode->data);
- len = bcm->ucode->size / sizeof(u32);
+ data = (u32 *)(phy->ucode->data);
+ len = phy->ucode->size / sizeof(u32);
bcm43xx_shm_control_word(bcm, BCM43xx_SHM_UCODE, 0x0000);
for (i = 0; i < len; i++) {
bcm43xx_write32(bcm, BCM43xx_MMIO_SHM_DATA,
@@ -2084,8 +2043,8 @@
}
/* Upload PCM data. */
- data = (u32 *)(bcm->pcm->data);
- len = bcm->pcm->size / sizeof(u32);
+ data = (u32 *)(phy->pcm->data);
+ len = phy->pcm->size / sizeof(u32);
bcm43xx_shm_control_word(bcm, BCM43xx_SHM_PCM, 0x01ea);
bcm43xx_write32(bcm, BCM43xx_MMIO_SHM_DATA, 0x00004000);
bcm43xx_shm_control_word(bcm, BCM43xx_SHM_PCM, 0x01eb);
@@ -2131,15 +2090,16 @@
static int bcm43xx_upload_initvals(struct bcm43xx_private *bcm)
{
+ struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
int err;
- err = bcm43xx_write_initvals(bcm, (struct bcm43xx_initval *)bcm->initvals0->data,
- bcm->initvals0->size / sizeof(struct bcm43xx_initval));
+ err = bcm43xx_write_initvals(bcm, (struct bcm43xx_initval *)phy->initvals0->data,
+ phy->initvals0->size / sizeof(struct bcm43xx_initval));
if (err)
goto out;
- if (bcm->initvals1) {
- err = bcm43xx_write_initvals(bcm, (struct bcm43xx_initval *)bcm->initvals1->data,
- bcm->initvals1->size / sizeof(struct bcm43xx_initval));
+ if (phy->initvals1) {
+ err = bcm43xx_write_initvals(bcm, (struct bcm43xx_initval *)phy->initvals1->data,
+ phy->initvals1->size / sizeof(struct bcm43xx_initval));
if (err)
goto out;
}
@@ -2156,9 +2116,7 @@
static int bcm43xx_initialize_irq(struct bcm43xx_private *bcm)
{
- int res;
- unsigned int i;
- u32 data;
+ int err;
bcm->irq = bcm->pci_dev->irq;
#ifdef CONFIG_BCM947XX
@@ -2175,32 +2133,12 @@
}
}
#endif
- res = request_irq(bcm->irq, bcm43xx_interrupt_handler,
+ err = request_irq(bcm->irq, bcm43xx_interrupt_handler,
IRQF_SHARED, KBUILD_MODNAME, bcm);
- if (res) {
+ if (err)
printk(KERN_ERR PFX "Cannot register IRQ%d\n", bcm->irq);
- return -ENODEV;
- }
- bcm43xx_write32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON, 0xffffffff);
- bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD, 0x00020402);
- i = 0;
- while (1) {
- data = bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
- if (data == BCM43xx_IRQ_READY)
- break;
- i++;
- if (i >= BCM43xx_IRQWAIT_MAX_RETRIES) {
- printk(KERN_ERR PFX "Card IRQ register not responding. "
- "Giving up.\n");
- free_irq(bcm->irq, bcm);
- return -ENODEV;
- }
- udelay(10);
- }
- // dummy read
- bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
- return 0;
+ return err;
}
/* Switch to the core used to write the GPIO register.
@@ -2298,13 +2236,17 @@
/* http://bcm-specs.sipsolutions.net/EnableMac */
void bcm43xx_mac_enable(struct bcm43xx_private *bcm)
{
- bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD,
- bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD)
- | BCM43xx_SBF_MAC_ENABLED);
- bcm43xx_write32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON, BCM43xx_IRQ_READY);
- bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD); /* dummy read */
- bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
- bcm43xx_power_saving_ctl_bits(bcm, -1, -1);
+ bcm->mac_suspended--;
+ assert(bcm->mac_suspended >= 0);
+ if (bcm->mac_suspended == 0) {
+ bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD,
+ bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD)
+ | BCM43xx_SBF_MAC_ENABLED);
+ bcm43xx_write32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON, BCM43xx_IRQ_READY);
+ bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD); /* dummy read */
+ bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
+ bcm43xx_power_saving_ctl_bits(bcm, -1, -1);
+ }
}
/* http://bcm-specs.sipsolutions.net/SuspendMAC */
@@ -2313,18 +2255,23 @@
int i;
u32 tmp;
- bcm43xx_power_saving_ctl_bits(bcm, -1, 1);
- bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD,
- bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD)
- & ~BCM43xx_SBF_MAC_ENABLED);
- bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
- for (i = 100000; i; i--) {
- tmp = bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
- if (tmp & BCM43xx_IRQ_READY)
- return;
- udelay(10);
+ assert(bcm->mac_suspended >= 0);
+ if (bcm->mac_suspended == 0) {
+ bcm43xx_power_saving_ctl_bits(bcm, -1, 1);
+ bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD,
+ bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD)
+ & ~BCM43xx_SBF_MAC_ENABLED);
+ bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
+ for (i = 10000; i; i--) {
+ tmp = bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
+ if (tmp & BCM43xx_IRQ_READY)
+ goto out;
+ udelay(1);
+ }
+ printkl(KERN_ERR PFX "MAC suspend failed\n");
}
- printkl(KERN_ERR PFX "MAC suspend failed\n");
+out:
+ bcm->mac_suspended++;
}
void bcm43xx_set_iwmode(struct bcm43xx_private *bcm,
@@ -2394,7 +2341,6 @@
if (!modparam_noleds)
bcm43xx_leds_exit(bcm);
bcm43xx_gpio_cleanup(bcm);
- free_irq(bcm->irq, bcm);
bcm43xx_release_firmware(bcm, 0);
}
@@ -2406,7 +2352,7 @@
struct bcm43xx_radioinfo *radio = bcm43xx_current_radio(bcm);
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
int err;
- int tmp;
+ int i, tmp;
u32 value32;
u16 value16;
@@ -2419,13 +2365,26 @@
goto out;
bcm43xx_upload_microcode(bcm);
- err = bcm43xx_initialize_irq(bcm);
- if (err)
- goto err_release_fw;
+ bcm43xx_write32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON, 0xFFFFFFFF);
+ bcm43xx_write32(bcm, BCM43xx_MMIO_STATUS_BITFIELD, 0x00020402);
+ i = 0;
+ while (1) {
+ value32 = bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON);
+ if (value32 == BCM43xx_IRQ_READY)
+ break;
+ i++;
+ if (i >= BCM43xx_IRQWAIT_MAX_RETRIES) {
+ printk(KERN_ERR PFX "IRQ_READY timeout\n");
+ err = -ENODEV;
+ goto err_release_fw;
+ }
+ udelay(10);
+ }
+ bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
err = bcm43xx_gpio_init(bcm);
if (err)
- goto err_free_irq;
+ goto err_release_fw;
err = bcm43xx_upload_initvals(bcm);
if (err)
@@ -2509,8 +2468,6 @@
bcm43xx_radio_turn_off(bcm);
err_gpio_cleanup:
bcm43xx_gpio_cleanup(bcm);
-err_free_irq:
- free_irq(bcm->irq, bcm);
err_release_fw:
bcm43xx_release_firmware(bcm, 1);
goto out;
@@ -2550,11 +2507,9 @@
{
/* Initialize a "phyinfo" structure. The structure is already
* zeroed out.
+ * This is called on insmod time to initialize members.
*/
- phy->antenna_diversity = 0xFFFF;
phy->savedpctlreg = 0xFFFF;
- phy->minlowsig[0] = 0xFFFF;
- phy->minlowsig[1] = 0xFFFF;
spin_lock_init(&phy->lock);
}
@@ -2562,14 +2517,11 @@
{
/* Initialize a "radioinfo" structure. The structure is already
* zeroed out.
+ * This is called on insmod time to initialize members.
*/
radio->interfmode = BCM43xx_RADIO_INTERFMODE_NONE;
radio->channel = 0xFF;
radio->initial_channel = 0xFF;
- radio->lofcal = 0xFFFF;
- radio->initval = 0xFFFF;
- radio->nrssi[0] = -1000;
- radio->nrssi[1] = -1000;
}
static int bcm43xx_probe_cores(struct bcm43xx_private *bcm)
@@ -2587,7 +2539,6 @@
* BCM43xx_MAX_80211_CORES);
memset(&bcm->core_80211_ext, 0, sizeof(struct bcm43xx_coreinfo_80211)
* BCM43xx_MAX_80211_CORES);
- bcm->current_80211_core_idx = -1;
bcm->nr_80211_available = 0;
bcm->current_core = NULL;
bcm->active_80211_core = NULL;
@@ -2757,6 +2708,7 @@
goto out;
}
bcm->nr_80211_available++;
+ core->priv = ext_80211;
bcm43xx_init_struct_phyinfo(&ext_80211->phy);
bcm43xx_init_struct_radioinfo(&ext_80211->radio);
break;
@@ -2857,7 +2809,8 @@
}
/* http://bcm-specs.sipsolutions.net/80211Init */
-static int bcm43xx_wireless_core_init(struct bcm43xx_private *bcm)
+static int bcm43xx_wireless_core_init(struct bcm43xx_private *bcm,
+ int active_wlcore)
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
struct bcm43xx_radioinfo *radio = bcm43xx_current_radio(bcm);
@@ -2939,19 +2892,26 @@
if (bcm->current_core->rev >= 5)
bcm43xx_write16(bcm, 0x043C, 0x000C);
- if (bcm43xx_using_pio(bcm))
- err = bcm43xx_pio_init(bcm);
- else
- err = bcm43xx_dma_init(bcm);
- if (err)
- goto err_chip_cleanup;
+ if (active_wlcore) {
+ if (bcm43xx_using_pio(bcm))
+ err = bcm43xx_pio_init(bcm);
+ else
+ err = bcm43xx_dma_init(bcm);
+ if (err)
+ goto err_chip_cleanup;
+ }
bcm43xx_write16(bcm, 0x0612, 0x0050);
bcm43xx_shm_write16(bcm, BCM43xx_SHM_SHARED, 0x0416, 0x0050);
bcm43xx_shm_write16(bcm, BCM43xx_SHM_SHARED, 0x0414, 0x01F4);
- bcm43xx_mac_enable(bcm);
- bcm43xx_interrupt_enable(bcm, bcm->irq_savedstate);
+ if (active_wlcore) {
+ if (radio->initial_channel != 0xFF)
+ bcm43xx_radio_selectchannel(bcm, radio->initial_channel, 0);
+ }
+ /* Don't enable MAC/IRQ here, as it will race with the IRQ handler.
+ * We enable it later.
+ */
bcm->current_core->initialized = 1;
out:
return err;
@@ -3066,11 +3026,6 @@
return err;
}
-static void bcm43xx_softmac_init(struct bcm43xx_private *bcm)
-{
- ieee80211softmac_start(bcm->net_dev);
-}
-
static void bcm43xx_periodic_every120sec(struct bcm43xx_private *bcm)
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
@@ -3182,39 +3137,40 @@
/* Periodic work will take a long time, so we want it to
* be preemtible.
*/
- bcm43xx_lock_irqonly(bcm, flags);
netif_stop_queue(bcm->net_dev);
+ synchronize_net();
+ spin_lock_irqsave(&bcm->irq_lock, flags);
+ bcm43xx_mac_suspend(bcm);
if (bcm43xx_using_pio(bcm))
bcm43xx_pio_freeze_txqueues(bcm);
savedirqs = bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
- bcm43xx_unlock_irqonly(bcm, flags);
- bcm43xx_lock_noirq(bcm);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_lock(&bcm->mutex);
bcm43xx_synchronize_irq(bcm);
} else {
/* Periodic work should take short time, so we want low
* locking overhead.
*/
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
}
do_periodic_work(bcm);
if (badness > BADNESS_LIMIT) {
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (likely(bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED)) {
tasklet_enable(&bcm->isr_tasklet);
bcm43xx_interrupt_enable(bcm, savedirqs);
if (bcm43xx_using_pio(bcm))
bcm43xx_pio_thaw_txqueues(bcm);
+ bcm43xx_mac_enable(bcm);
}
netif_wake_queue(bcm->net_dev);
- mmiowb();
- bcm43xx_unlock_irqonly(bcm, flags);
- bcm43xx_unlock_noirq(bcm);
- } else {
- mmiowb();
- bcm43xx_unlock_irqsafe(bcm, flags);
}
+ mmiowb();
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
}
static void bcm43xx_periodic_tasks_delete(struct bcm43xx_private *bcm)
@@ -3243,9 +3199,9 @@
struct bcm43xx_private *bcm = (struct bcm43xx_private *)rng->priv;
unsigned long flags;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&(bcm)->irq_lock, flags);
*data = bcm43xx_read16(bcm, BCM43xx_MMIO_RNG);
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&(bcm)->irq_lock, flags);
return (sizeof(u16));
}
@@ -3271,139 +3227,322 @@
return err;
}
+static int bcm43xx_shutdown_all_wireless_cores(struct bcm43xx_private *bcm)
+{
+ int ret = 0;
+ int i, err;
+ struct bcm43xx_coreinfo *core;
+
+ bcm43xx_set_status(bcm, BCM43xx_STAT_SHUTTINGDOWN);
+ for (i = 0; i < bcm->nr_80211_available; i++) {
+ core = &(bcm->core_80211[i]);
+ assert(core->available);
+ if (!core->initialized)
+ continue;
+ err = bcm43xx_switch_core(bcm, core);
+ if (err) {
+ dprintk(KERN_ERR PFX "shutdown_all_wireless_cores "
+ "switch_core failed (%d)\n", err);
+ ret = err;
+ continue;
+ }
+ bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
+ bcm43xx_read32(bcm, BCM43xx_MMIO_GEN_IRQ_REASON); /* dummy read */
+ bcm43xx_wireless_core_cleanup(bcm);
+ if (core == bcm->active_80211_core)
+ bcm->active_80211_core = NULL;
+ }
+ free_irq(bcm->irq, bcm);
+ bcm43xx_set_status(bcm, BCM43xx_STAT_UNINIT);
+
+ return ret;
+}
+
/* This is the opposite of bcm43xx_init_board() */
static void bcm43xx_free_board(struct bcm43xx_private *bcm)
{
- int i, err;
-
- bcm43xx_lock_noirq(bcm);
bcm43xx_sysfs_unregister(bcm);
bcm43xx_periodic_tasks_delete(bcm);
- bcm43xx_set_status(bcm, BCM43xx_STAT_SHUTTINGDOWN);
+ mutex_lock(&(bcm)->mutex);
+ bcm43xx_shutdown_all_wireless_cores(bcm);
+ bcm43xx_pctl_set_crystal(bcm, 0);
+ mutex_unlock(&(bcm)->mutex);
+}
- bcm43xx_rng_exit(bcm);
+static void prepare_phydata_for_init(struct bcm43xx_phyinfo *phy)
+{
+ phy->antenna_diversity = 0xFFFF;
+ memset(phy->minlowsig, 0xFF, sizeof(phy->minlowsig));
+ memset(phy->minlowsigpos, 0, sizeof(phy->minlowsigpos));
+
+ /* Flags */
+ phy->calibrated = 0;
+ phy->is_locked = 0;
+
+ if (phy->_lo_pairs) {
+ memset(phy->_lo_pairs, 0,
+ sizeof(struct bcm43xx_lopair) * BCM43xx_LO_COUNT);
+ }
+ memset(phy->loopback_gain, 0, sizeof(phy->loopback_gain));
+}
+
+static void prepare_radiodata_for_init(struct bcm43xx_private *bcm,
+ struct bcm43xx_radioinfo *radio)
+{
+ int i;
+
+ /* Set default attenuation values. */
+ radio->baseband_atten = bcm43xx_default_baseband_attenuation(bcm);
+ radio->radio_atten = bcm43xx_default_radio_attenuation(bcm);
+ radio->txctl1 = bcm43xx_default_txctl1(bcm);
+ radio->txctl2 = 0xFFFF;
+ radio->txpwr_offset = 0;
+
+ /* NRSSI */
+ radio->nrssislope = 0;
+ for (i = 0; i < ARRAY_SIZE(radio->nrssi); i++)
+ radio->nrssi[i] = -1000;
+ for (i = 0; i < ARRAY_SIZE(radio->nrssi_lt); i++)
+ radio->nrssi_lt[i] = i;
+
+ radio->lofcal = 0xFFFF;
+ radio->initval = 0xFFFF;
+
+ radio->aci_enable = 0;
+ radio->aci_wlan_automatic = 0;
+ radio->aci_hw_rssi = 0;
+}
+
+static void prepare_priv_for_init(struct bcm43xx_private *bcm)
+{
+ int i;
+ struct bcm43xx_coreinfo *core;
+ struct bcm43xx_coreinfo_80211 *wlext;
+
+ assert(!bcm->active_80211_core);
+
+ bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZING);
+
+ /* Flags */
+ bcm->was_initialized = 0;
+ bcm->reg124_set_0x4 = 0;
+
+ /* Stats */
+ memset(&bcm->stats, 0, sizeof(bcm->stats));
+
+ /* Wireless core data */
for (i = 0; i < BCM43xx_MAX_80211_CORES; i++) {
- if (!bcm->core_80211[i].available)
- continue;
- if (!bcm->core_80211[i].initialized)
- continue;
+ core = &(bcm->core_80211[i]);
+ wlext = core->priv;
- err = bcm43xx_switch_core(bcm, &bcm->core_80211[i]);
- assert(err == 0);
- bcm43xx_wireless_core_cleanup(bcm);
+ if (!core->available)
+ continue;
+ assert(wlext == &(bcm->core_80211_ext[i]));
+
+ prepare_phydata_for_init(&wlext->phy);
+ prepare_radiodata_for_init(bcm, &wlext->radio);
}
- bcm43xx_pctl_set_crystal(bcm, 0);
+ /* IRQ related flags */
+ bcm->irq_reason = 0;
+ memset(bcm->dma_reason, 0, sizeof(bcm->dma_reason));
+ bcm->irq_savedstate = BCM43xx_IRQ_INITIAL;
+ /* Noise calculation context */
+ memset(&bcm->noisecalc, 0, sizeof(bcm->noisecalc));
+
+ /* Periodic work context */
+ bcm->periodic_state = 0;
+}
+
+static int wireless_core_up(struct bcm43xx_private *bcm,
+ int active_wlcore)
+{
+ int err;
+
+ if (!bcm43xx_core_enabled(bcm))
+ bcm43xx_wireless_core_reset(bcm, 1);
+ if (!active_wlcore)
+ bcm43xx_wireless_core_mark_inactive(bcm);
+ err = bcm43xx_wireless_core_init(bcm, active_wlcore);
+ if (err)
+ goto out;
+ if (!active_wlcore)
+ bcm43xx_radio_turn_off(bcm);
+out:
+ return err;
+}
+
+/* Select and enable the "to be used" wireless core.
+ * Locking: bcm->mutex must be aquired before calling this.
+ * bcm->irq_lock must not be aquired.
+ */
+int bcm43xx_select_wireless_core(struct bcm43xx_private *bcm,
+ int phytype)
+{
+ int i, err;
+ struct bcm43xx_coreinfo *active_core = NULL;
+ struct bcm43xx_coreinfo_80211 *active_wlext = NULL;
+ struct bcm43xx_coreinfo *core;
+ struct bcm43xx_coreinfo_80211 *wlext;
+ int adjust_active_sbtmstatelow = 0;
+
+ might_sleep();
+
+ if (phytype < 0) {
+ /* If no phytype is requested, select the first core. */
+ assert(bcm->core_80211[0].available);
+ wlext = bcm->core_80211[0].priv;
+ phytype = wlext->phy.type;
+ }
+ /* Find the requested core. */
+ for (i = 0; i < bcm->nr_80211_available; i++) {
+ core = &(bcm->core_80211[i]);
+ wlext = core->priv;
+ if (wlext->phy.type == phytype) {
+ active_core = core;
+ active_wlext = wlext;
+ break;
+ }
+ }
+ if (!active_core)
+ return -ESRCH; /* No such PHYTYPE on this board. */
+
+ if (bcm->active_80211_core) {
+ /* We already selected a wl core in the past.
+ * So first clean up everything.
+ */
+ dprintk(KERN_INFO PFX "select_wireless_core: cleanup\n");
+ ieee80211softmac_stop(bcm->net_dev);
+ bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZED);
+ err = bcm43xx_disable_interrupts_sync(bcm);
+ assert(!err);
+ tasklet_enable(&bcm->isr_tasklet);
+ err = bcm43xx_shutdown_all_wireless_cores(bcm);
+ if (err)
+ goto error;
+ /* Ok, everything down, continue to re-initialize. */
+ bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZING);
+ }
+
+ /* Reset all data structures. */
+ prepare_priv_for_init(bcm);
+
+ err = bcm43xx_pctl_set_clock(bcm, BCM43xx_PCTL_CLK_FAST);
+ if (err)
+ goto error;
+
+ /* Mark all unused cores "inactive". */
+ for (i = 0; i < bcm->nr_80211_available; i++) {
+ core = &(bcm->core_80211[i]);
+ wlext = core->priv;
+
+ if (core == active_core)
+ continue;
+ err = bcm43xx_switch_core(bcm, core);
+ if (err) {
+ dprintk(KERN_ERR PFX "Could not switch to inactive "
+ "802.11 core (%d)\n", err);
+ goto error;
+ }
+ err = wireless_core_up(bcm, 0);
+ if (err) {
+ dprintk(KERN_ERR PFX "core_up for inactive 802.11 core "
+ "failed (%d)\n", err);
+ goto error;
+ }
+ adjust_active_sbtmstatelow = 1;
+ }
+
+ /* Now initialize the active 802.11 core. */
+ err = bcm43xx_switch_core(bcm, active_core);
+ if (err) {
+ dprintk(KERN_ERR PFX "Could not switch to active "
+ "802.11 core (%d)\n", err);
+ goto error;
+ }
+ if (adjust_active_sbtmstatelow &&
+ active_wlext->phy.type == BCM43xx_PHYTYPE_G) {
+ u32 sbtmstatelow;
+
+ sbtmstatelow = bcm43xx_read32(bcm, BCM43xx_CIR_SBTMSTATELOW);
+ sbtmstatelow |= 0x20000000;
+ bcm43xx_write32(bcm, BCM43xx_CIR_SBTMSTATELOW, sbtmstatelow);
+ }
+ err = wireless_core_up(bcm, 1);
+ if (err) {
+ dprintk(KERN_ERR PFX "core_up for active 802.11 core "
+ "failed (%d)\n", err);
+ goto error;
+ }
+ err = bcm43xx_pctl_set_clock(bcm, BCM43xx_PCTL_CLK_DYNAMIC);
+ if (err)
+ goto error;
+ bcm->active_80211_core = active_core;
+
+ bcm43xx_macfilter_clear(bcm, BCM43xx_MACFILTER_ASSOC);
+ bcm43xx_macfilter_set(bcm, BCM43xx_MACFILTER_SELF, (u8 *)(bcm->net_dev->dev_addr));
+ bcm43xx_security_init(bcm);
+ ieee80211softmac_start(bcm->net_dev);
+
+ /* Let's go! Be careful after enabling the IRQs.
+ * Don't switch cores, for example.
+ */
+ bcm43xx_mac_enable(bcm);
+ bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZED);
+ err = bcm43xx_initialize_irq(bcm);
+ if (err)
+ goto error;
+ bcm43xx_interrupt_enable(bcm, bcm->irq_savedstate);
+
+ dprintk(KERN_INFO PFX "Selected 802.11 core (phytype %d)\n",
+ active_wlext->phy.type);
+
+ return 0;
+
+error:
bcm43xx_set_status(bcm, BCM43xx_STAT_UNINIT);
- bcm43xx_unlock_noirq(bcm);
+ bcm43xx_pctl_set_clock(bcm, BCM43xx_PCTL_CLK_SLOW);
+ return err;
}
static int bcm43xx_init_board(struct bcm43xx_private *bcm)
{
- int i, err;
- int connect_phy;
+ int err;
- might_sleep();
+ mutex_lock(&(bcm)->mutex);
- bcm43xx_lock_noirq(bcm);
- bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZING);
-
+ tasklet_enable(&bcm->isr_tasklet);
err = bcm43xx_pctl_set_crystal(bcm, 1);
if (err)
- goto out;
+ goto err_tasklet;
err = bcm43xx_pctl_init(bcm);
if (err)
goto err_crystal_off;
- err = bcm43xx_pctl_set_clock(bcm, BCM43xx_PCTL_CLK_FAST);
+ err = bcm43xx_select_wireless_core(bcm, -1);
if (err)
goto err_crystal_off;
- tasklet_enable(&bcm->isr_tasklet);
- for (i = 0; i < bcm->nr_80211_available; i++) {
- err = bcm43xx_switch_core(bcm, &bcm->core_80211[i]);
- assert(err != -ENODEV);
- if (err)
- goto err_80211_unwind;
-
- /* Enable the selected wireless core.
- * Connect PHY only on the first core.
- */
- if (!bcm43xx_core_enabled(bcm)) {
- if (bcm->nr_80211_available == 1) {
- connect_phy = bcm43xx_current_phy(bcm)->connected;
- } else {
- if (i == 0)
- connect_phy = 1;
- else
- connect_phy = 0;
- }
- bcm43xx_wireless_core_reset(bcm, connect_phy);
- }
-
- if (i != 0)
- bcm43xx_wireless_core_mark_inactive(bcm, &bcm->core_80211[0]);
-
- err = bcm43xx_wireless_core_init(bcm);
- if (err)
- goto err_80211_unwind;
-
- if (i != 0) {
- bcm43xx_mac_suspend(bcm);
- bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
- bcm43xx_radio_turn_off(bcm);
- }
- }
- bcm->active_80211_core = &bcm->core_80211[0];
- if (bcm->nr_80211_available >= 2) {
- bcm43xx_switch_core(bcm, &bcm->core_80211[0]);
- bcm43xx_mac_enable(bcm);
- }
- err = bcm43xx_rng_init(bcm);
- if (err)
- goto err_80211_unwind;
- bcm43xx_macfilter_clear(bcm, BCM43xx_MACFILTER_ASSOC);
- bcm43xx_macfilter_set(bcm, BCM43xx_MACFILTER_SELF, (u8 *)(bcm->net_dev->dev_addr));
- dprintk(KERN_INFO PFX "80211 cores initialized\n");
- bcm43xx_security_init(bcm);
- bcm43xx_softmac_init(bcm);
-
- bcm43xx_pctl_set_clock(bcm, BCM43xx_PCTL_CLK_DYNAMIC);
-
- if (bcm43xx_current_radio(bcm)->initial_channel != 0xFF) {
- bcm43xx_mac_suspend(bcm);
- bcm43xx_radio_selectchannel(bcm, bcm43xx_current_radio(bcm)->initial_channel, 0);
- bcm43xx_mac_enable(bcm);
- }
-
- /* Initialization of the board is done. Flag it as such. */
- bcm43xx_set_status(bcm, BCM43xx_STAT_INITIALIZED);
-
bcm43xx_periodic_tasks_setup(bcm);
- bcm43xx_sysfs_register(bcm);
- //FIXME: check for bcm43xx_sysfs_register failure. This function is a bit messy regarding unwinding, though...
+ err = bcm43xx_sysfs_register(bcm);
+ if (err)
+ goto err_wlshutdown;
/*FIXME: This should be handled by softmac instead. */
schedule_work(&bcm->softmac->associnfo.work);
- assert(err == 0);
out:
- bcm43xx_unlock_noirq(bcm);
+ mutex_unlock(&(bcm)->mutex);
return err;
-err_80211_unwind:
- tasklet_disable(&bcm->isr_tasklet);
- /* unwind all 80211 initialization */
- for (i = 0; i < bcm->nr_80211_available; i++) {
- if (!bcm->core_80211[i].initialized)
- continue;
- bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
- bcm43xx_wireless_core_cleanup(bcm);
- }
+err_wlshutdown:
+ bcm43xx_shutdown_all_wireless_cores(bcm);
err_crystal_off:
bcm43xx_pctl_set_crystal(bcm, 0);
+err_tasklet:
+ tasklet_disable(&bcm->isr_tasklet);
goto out;
}
@@ -3647,7 +3786,8 @@
struct bcm43xx_radioinfo *radio;
unsigned long flags;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED) {
bcm43xx_mac_suspend(bcm);
bcm43xx_radio_selectchannel(bcm, channel, 0);
@@ -3656,7 +3796,8 @@
radio = bcm43xx_current_radio(bcm);
radio->initial_channel = channel;
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
}
/* set_security() callback in struct ieee80211_device */
@@ -3670,7 +3811,8 @@
dprintk(KERN_INFO PFX "set security called");
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
for (keyidx = 0; keyidx<WEP_KEYS; keyidx++)
if (sec->flags & (1<<keyidx)) {
@@ -3739,7 +3881,8 @@
} else
bcm43xx_clear_keys(bcm);
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
}
/* hard_start_xmit() callback in struct ieee80211_device */
@@ -3751,10 +3894,10 @@
int err = -ENODEV;
unsigned long flags;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (likely(bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED))
err = bcm43xx_tx(bcm, txb);
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
return err;
}
@@ -3769,9 +3912,9 @@
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
unsigned long flags;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
bcm43xx_controller_restart(bcm, "TX timeout");
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
}
#ifdef CONFIG_NET_POLL_CONTROLLER
@@ -3781,7 +3924,8 @@
unsigned long flags;
local_irq_save(flags);
- bcm43xx_interrupt_handler(bcm->irq, bcm, NULL);
+ if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED)
+ bcm43xx_interrupt_handler(bcm->irq, bcm, NULL);
local_irq_restore(flags);
}
#endif /* CONFIG_NET_POLL_CONTROLLER */
@@ -3799,7 +3943,7 @@
int err;
ieee80211softmac_stop(net_dev);
- err = bcm43xx_disable_interrupts_sync(bcm, NULL);
+ err = bcm43xx_disable_interrupts_sync(bcm);
assert(!err);
bcm43xx_free_board(bcm);
@@ -3818,10 +3962,12 @@
bcm->softmac->set_channel = bcm43xx_ieee80211_set_chan;
bcm->irq_savedstate = BCM43xx_IRQ_INITIAL;
+ bcm->mac_suspended = 1;
bcm->pci_dev = pci_dev;
bcm->net_dev = net_dev;
bcm->bad_frames_preempt = modparam_bad_frames_preempt;
spin_lock_init(&bcm->irq_lock);
+ spin_lock_init(&bcm->leds_lock);
mutex_init(&bcm->mutex);
tasklet_init(&bcm->isr_tasklet,
(void (*)(unsigned long))bcm43xx_interrupt_tasklet,
@@ -3940,7 +4086,6 @@
bcm43xx_debugfs_remove_device(bcm);
unregister_netdev(net_dev);
bcm43xx_detach_board(bcm);
- assert(bcm->ucode == NULL);
free_ieee80211softmac(net_dev);
}
@@ -3950,47 +4095,25 @@
static void bcm43xx_chip_reset(void *_bcm)
{
struct bcm43xx_private *bcm = _bcm;
- struct net_device *net_dev = bcm->net_dev;
- struct pci_dev *pci_dev = bcm->pci_dev;
+ struct bcm43xx_phyinfo *phy;
int err;
- int was_initialized = (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED);
- netif_stop_queue(bcm->net_dev);
- tasklet_disable(&bcm->isr_tasklet);
+ mutex_lock(&(bcm)->mutex);
+ phy = bcm43xx_current_phy(bcm);
+ err = bcm43xx_select_wireless_core(bcm, phy->type);
+ mutex_unlock(&(bcm)->mutex);
- bcm->firmware_norelease = 1;
- if (was_initialized)
- bcm43xx_free_board(bcm);
- bcm->firmware_norelease = 0;
- bcm43xx_detach_board(bcm);
- err = bcm43xx_init_private(bcm, net_dev, pci_dev);
- if (err)
- goto failure;
- err = bcm43xx_attach_board(bcm);
- if (err)
- goto failure;
- if (was_initialized) {
- err = bcm43xx_init_board(bcm);
- if (err)
- goto failure;
- }
- netif_wake_queue(bcm->net_dev);
- printk(KERN_INFO PFX "Controller restarted\n");
-
- return;
-failure:
- printk(KERN_ERR PFX "Controller restart failed\n");
+ printk(KERN_ERR PFX "Controller restart%s\n",
+ (err == 0) ? "ed" : " failed");
}
/* Hard-reset the chip.
* This can be called from interrupt or process context.
- * Make sure to _not_ re-enable device interrupts after this has been called.
-*/
+ */
void bcm43xx_controller_restart(struct bcm43xx_private *bcm, const char *reason)
{
+ assert(bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED);
bcm43xx_set_status(bcm, BCM43xx_STAT_RESTARTING);
- bcm43xx_interrupt_disable(bcm, BCM43xx_IRQ_ALL);
- bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD); /* dummy read */
printk(KERN_ERR PFX "Controller RESET (%s) ...\n", reason);
INIT_WORK(&bcm->restart_work, bcm43xx_chip_reset, bcm);
schedule_work(&bcm->restart_work);
@@ -4002,21 +4125,16 @@
{
struct net_device *net_dev = pci_get_drvdata(pdev);
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
- int try_to_shutdown = 0, err;
+ int err;
dprintk(KERN_INFO PFX "Suspending...\n");
- bcm43xx_lock_irqsafe(bcm, flags);
- bcm->was_initialized = (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED);
- if (bcm->was_initialized)
- try_to_shutdown = 1;
- bcm43xx_unlock_irqsafe(bcm, flags);
-
netif_device_detach(net_dev);
- if (try_to_shutdown) {
+ bcm->was_initialized = 0;
+ if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED) {
+ bcm->was_initialized = 1;
ieee80211softmac_stop(net_dev);
- err = bcm43xx_disable_interrupts_sync(bcm, &bcm->irq_savedstate);
+ err = bcm43xx_disable_interrupts_sync(bcm);
if (unlikely(err)) {
dprintk(KERN_ERR PFX "Suspend failed.\n");
return -EAGAIN;
@@ -4049,17 +4167,14 @@
pci_restore_state(pdev);
bcm43xx_chipset_attach(bcm);
- if (bcm->was_initialized) {
- bcm->irq_savedstate = BCM43xx_IRQ_INITIAL;
+ if (bcm->was_initialized)
err = bcm43xx_init_board(bcm);
- }
if (err) {
printk(KERN_ERR PFX "Resume failed!\n");
return err;
}
-
netif_device_attach(net_dev);
-
+
dprintk(KERN_INFO PFX "Device resumed.\n");
return 0;
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_main.h b/drivers/net/wireless/bcm43xx/bcm43xx_main.h
index 1164936..505c86e 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_main.h
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_main.h
@@ -133,6 +133,9 @@
int bcm43xx_switch_core(struct bcm43xx_private *bcm, struct bcm43xx_coreinfo *new_core);
+int bcm43xx_select_wireless_core(struct bcm43xx_private *bcm,
+ int phytype);
+
void bcm43xx_wireless_core_reset(struct bcm43xx_private *bcm, int connect_phy);
void bcm43xx_mac_suspend(struct bcm43xx_private *bcm);
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c
index f8200de..eafd0f6 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c
@@ -81,6 +81,16 @@
static void bcm43xx_phy_initg(struct bcm43xx_private *bcm);
+static inline
+void bcm43xx_voluntary_preempt(void)
+{
+ assert(!in_atomic() && !in_irq() &&
+ !in_interrupt() && !irqs_disabled());
+#ifndef CONFIG_PREEMPT
+ cond_resched();
+#endif /* CONFIG_PREEMPT */
+}
+
void bcm43xx_raw_phy_lock(struct bcm43xx_private *bcm)
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
@@ -133,22 +143,14 @@
void bcm43xx_phy_calibrate(struct bcm43xx_private *bcm)
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
- unsigned long flags;
bcm43xx_read32(bcm, BCM43xx_MMIO_STATUS_BITFIELD); /* Dummy read. */
if (phy->calibrated)
return;
if (phy->type == BCM43xx_PHYTYPE_G && phy->rev == 1) {
- /* We do not want to be preempted while calibrating
- * the hardware.
- */
- local_irq_save(flags);
-
bcm43xx_wireless_core_reset(bcm, 0);
bcm43xx_phy_initg(bcm);
bcm43xx_wireless_core_reset(bcm, 1);
-
- local_irq_restore(flags);
}
phy->calibrated = 1;
}
@@ -1299,7 +1301,9 @@
{
int i;
u16 ret = 0;
+ unsigned long flags;
+ local_irq_save(flags);
for (i = 0; i < 10; i++){
bcm43xx_phy_write(bcm, 0x0015, 0xAFA0);
udelay(1);
@@ -1309,6 +1313,8 @@
udelay(40);
ret += bcm43xx_phy_read(bcm, 0x002C);
}
+ local_irq_restore(flags);
+ bcm43xx_voluntary_preempt();
return ret;
}
@@ -1435,6 +1441,7 @@
}
ret = bcm43xx_phy_read(bcm, 0x002D);
local_irq_restore(flags);
+ bcm43xx_voluntary_preempt();
return ret;
}
@@ -1760,6 +1767,7 @@
bcm43xx_radio_write16(bcm, 0x43, i);
bcm43xx_radio_write16(bcm, 0x52, radio->txctl2);
udelay(10);
+ bcm43xx_voluntary_preempt();
bcm43xx_phy_set_baseband_attenuation(bcm, j * 2);
@@ -1803,6 +1811,7 @@
radio->txctl2
| (3/*txctl1*/ << 4));//FIXME: shouldn't txctl1 be zero here and 3 in the loop above?
udelay(10);
+ bcm43xx_voluntary_preempt();
bcm43xx_phy_set_baseband_attenuation(bcm, j * 2);
@@ -1824,6 +1833,7 @@
bcm43xx_phy_write(bcm, 0x0812, (r27 << 8) | 0xA2);
udelay(2);
bcm43xx_phy_write(bcm, 0x0812, (r27 << 8) | 0xA3);
+ bcm43xx_voluntary_preempt();
} else
bcm43xx_phy_write(bcm, 0x0015, r27 | 0xEFA0);
bcm43xx_phy_lo_adjust(bcm, is_initializing);
@@ -2188,12 +2198,6 @@
{
struct bcm43xx_phyinfo *phy = bcm43xx_current_phy(bcm);
int err = -ENODEV;
- unsigned long flags;
-
- /* We do not want to be preempted while calibrating
- * the hardware.
- */
- local_irq_save(flags);
switch (phy->type) {
case BCM43xx_PHYTYPE_A:
@@ -2227,7 +2231,6 @@
err = 0;
break;
}
- local_irq_restore(flags);
if (err)
printk(KERN_WARNING PFX "Unknown PHYTYPE found!\n");
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_pio.c b/drivers/net/wireless/bcm43xx/bcm43xx_pio.c
index 574085c..c60c174 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_pio.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_pio.c
@@ -262,7 +262,7 @@
int err;
u16 txctl;
- bcm43xx_lock_irqonly(bcm, flags);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (queue->tx_frozen)
goto out_unlock;
@@ -300,7 +300,7 @@
continue;
}
out_unlock:
- bcm43xx_unlock_irqonly(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
}
static void setup_txqueues(struct bcm43xx_pioqueue *queue)
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_sysfs.c b/drivers/net/wireless/bcm43xx/bcm43xx_sysfs.c
index 6a23bdc..ece3351 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_sysfs.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_sysfs.c
@@ -120,12 +120,14 @@
GFP_KERNEL);
if (!sprom)
return -ENOMEM;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
err = bcm43xx_sprom_read(bcm, sprom);
if (!err)
err = sprom2hex(sprom, buf, PAGE_SIZE);
mmiowb();
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
kfree(sprom);
return err;
@@ -150,10 +152,14 @@
err = hex2sprom(sprom, buf, count);
if (err)
goto out_kfree;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
+ spin_lock(&bcm->leds_lock);
err = bcm43xx_sprom_write(bcm, sprom);
mmiowb();
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock(&bcm->leds_lock);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
out_kfree:
kfree(sprom);
@@ -176,7 +182,7 @@
if (!capable(CAP_NET_ADMIN))
return -EPERM;
- bcm43xx_lock_noirq(bcm);
+ mutex_lock(&bcm->mutex);
switch (bcm43xx_current_radio(bcm)->interfmode) {
case BCM43xx_RADIO_INTERFMODE_NONE:
@@ -193,7 +199,7 @@
}
err = 0;
- bcm43xx_unlock_noirq(bcm);
+ mutex_unlock(&bcm->mutex);
return err ? err : count;
@@ -229,7 +235,8 @@
return -EINVAL;
}
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
err = bcm43xx_radio_set_interference_mitigation(bcm, mode);
if (err) {
@@ -237,7 +244,8 @@
"supported by device\n");
}
mmiowb();
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err ? err : count;
}
@@ -257,7 +265,7 @@
if (!capable(CAP_NET_ADMIN))
return -EPERM;
- bcm43xx_lock_noirq(bcm);
+ mutex_lock(&bcm->mutex);
if (bcm->short_preamble)
count = snprintf(buf, PAGE_SIZE, "1 (Short Preamble enabled)\n");
@@ -265,7 +273,7 @@
count = snprintf(buf, PAGE_SIZE, "0 (Short Preamble disabled)\n");
err = 0;
- bcm43xx_unlock_noirq(bcm);
+ mutex_unlock(&bcm->mutex);
return err ? err : count;
}
@@ -285,12 +293,14 @@
value = get_boolean(buf, count);
if (value < 0)
return value;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
bcm->short_preamble = !!value;
err = 0;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err ? err : count;
}
@@ -299,6 +309,70 @@
bcm43xx_attr_preamble_show,
bcm43xx_attr_preamble_store);
+static ssize_t bcm43xx_attr_phymode_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct bcm43xx_private *bcm = dev_to_bcm(dev);
+ int phytype;
+ int err = -EINVAL;
+
+ if (count < 1)
+ goto out;
+ switch (buf[0]) {
+ case 'a': case 'A':
+ phytype = BCM43xx_PHYTYPE_A;
+ break;
+ case 'b': case 'B':
+ phytype = BCM43xx_PHYTYPE_B;
+ break;
+ case 'g': case 'G':
+ phytype = BCM43xx_PHYTYPE_G;
+ break;
+ default:
+ goto out;
+ }
+
+ mutex_lock(&(bcm)->mutex);
+ err = bcm43xx_select_wireless_core(bcm, phytype);
+ mutex_unlock(&(bcm)->mutex);
+ if (err == -ESRCH)
+ err = -ENODEV;
+
+out:
+ return err ? err : count;
+}
+
+static ssize_t bcm43xx_attr_phymode_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct bcm43xx_private *bcm = dev_to_bcm(dev);
+ ssize_t count = 0;
+
+ mutex_lock(&(bcm)->mutex);
+ switch (bcm43xx_current_phy(bcm)->type) {
+ case BCM43xx_PHYTYPE_A:
+ snprintf(buf, PAGE_SIZE, "A");
+ break;
+ case BCM43xx_PHYTYPE_B:
+ snprintf(buf, PAGE_SIZE, "B");
+ break;
+ case BCM43xx_PHYTYPE_G:
+ snprintf(buf, PAGE_SIZE, "G");
+ break;
+ default:
+ assert(0);
+ }
+ mutex_unlock(&(bcm)->mutex);
+
+ return count;
+}
+
+static DEVICE_ATTR(phymode, 0644,
+ bcm43xx_attr_phymode_show,
+ bcm43xx_attr_phymode_store);
+
int bcm43xx_sysfs_register(struct bcm43xx_private *bcm)
{
struct device *dev = &bcm->pci_dev->dev;
@@ -315,9 +389,14 @@
err = device_create_file(dev, &dev_attr_shortpreamble);
if (err)
goto err_remove_interfmode;
+ err = device_create_file(dev, &dev_attr_phymode);
+ if (err)
+ goto err_remove_shortpreamble;
out:
return err;
+err_remove_shortpreamble:
+ device_remove_file(dev, &dev_attr_shortpreamble);
err_remove_interfmode:
device_remove_file(dev, &dev_attr_interference);
err_remove_sprom:
@@ -329,6 +408,7 @@
{
struct device *dev = &bcm->pci_dev->dev;
+ device_remove_file(dev, &dev_attr_phymode);
device_remove_file(dev, &dev_attr_shortpreamble);
device_remove_file(dev, &dev_attr_interference);
device_remove_file(dev, &dev_attr_sprom);
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_wx.c b/drivers/net/wireless/bcm43xx/bcm43xx_wx.c
index 5c36e29..1d3a3aa 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_wx.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_wx.c
@@ -47,6 +47,8 @@
#define BCM43xx_WX_VERSION 18
#define MAX_WX_STRING 80
+/* FIXME: the next line is a guess as to what the maximum RSSI value might be */
+#define RX_RSSI_MAX 60
static int bcm43xx_wx_get_name(struct net_device *net_dev,
@@ -56,12 +58,11 @@
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
int i;
- unsigned long flags;
struct bcm43xx_phyinfo *phy;
char suffix[7] = { 0 };
int have_a = 0, have_b = 0, have_g = 0;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
for (i = 0; i < bcm->nr_80211_available; i++) {
phy = &(bcm->core_80211_ext[i].phy);
switch (phy->type) {
@@ -77,7 +78,7 @@
assert(0);
}
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
i = 0;
if (have_a) {
@@ -111,7 +112,9 @@
int freq;
int err = -EINVAL;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
+
if ((data->freq.m >= 0) && (data->freq.m <= 1000)) {
channel = data->freq.m;
freq = bcm43xx_channel_to_freq(bcm, channel);
@@ -131,7 +134,8 @@
err = 0;
}
out_unlock:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -143,11 +147,10 @@
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
struct bcm43xx_radioinfo *radio;
- unsigned long flags;
int err = -ENODEV;
u16 channel;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
radio = bcm43xx_current_radio(bcm);
channel = radio->channel;
if (channel == 0xFF) {
@@ -162,7 +165,7 @@
err = 0;
out_unlock:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -180,13 +183,15 @@
if (mode == IW_MODE_AUTO)
mode = BCM43xx_INITIAL_IWMODE;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED) {
if (bcm->ieee->iw_mode != mode)
bcm43xx_set_iwmode(bcm, mode);
} else
bcm->ieee->iw_mode = mode;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -197,11 +202,10 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
data->mode = bcm->ieee->iw_mode;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -214,7 +218,6 @@
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
struct iw_range *range = (struct iw_range *)extra;
const struct ieee80211_geo *geo;
- unsigned long flags;
int i, j;
struct bcm43xx_phyinfo *phy;
@@ -226,15 +229,14 @@
range->throughput = 27 * 1000 * 1000;
range->max_qual.qual = 100;
- /* TODO: Real max RSSI */
- range->max_qual.level = 3;
- range->max_qual.noise = 100;
- range->max_qual.updated = 7;
+ range->max_qual.level = 152; /* set floor at -104 dBm (152 - 256) */
+ range->max_qual.noise = 152;
+ range->max_qual.updated = IW_QUAL_ALL_UPDATED;
- range->avg_qual.qual = 70;
- range->avg_qual.level = 2;
- range->avg_qual.noise = 40;
- range->avg_qual.updated = 7;
+ range->avg_qual.qual = 50;
+ range->avg_qual.level = 0;
+ range->avg_qual.noise = 0;
+ range->avg_qual.updated = IW_QUAL_ALL_UPDATED;
range->min_rts = BCM43xx_MIN_RTS_THRESHOLD;
range->max_rts = BCM43xx_MAX_RTS_THRESHOLD;
@@ -254,7 +256,7 @@
IW_ENC_CAPA_CIPHER_TKIP |
IW_ENC_CAPA_CIPHER_CCMP;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
phy = bcm43xx_current_phy(bcm);
range->num_bitrates = 0;
@@ -301,7 +303,7 @@
}
range->num_frequency = j;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -314,11 +316,11 @@
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
size_t len;
- bcm43xx_lock_noirq(bcm);
+ mutex_lock(&bcm->mutex);
len = min((size_t)data->data.length, (size_t)IW_ESSID_MAX_SIZE);
memcpy(bcm->nick, extra, len);
bcm->nick[len] = '\0';
- bcm43xx_unlock_noirq(bcm);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -331,12 +333,12 @@
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
size_t len;
- bcm43xx_lock_noirq(bcm);
+ mutex_lock(&bcm->mutex);
len = strlen(bcm->nick) + 1;
memcpy(extra, bcm->nick, len);
data->data.length = (__u16)len;
data->data.flags = 1;
- bcm43xx_unlock_noirq(bcm);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -350,7 +352,8 @@
unsigned long flags;
int err = -EINVAL;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (data->rts.disabled) {
bcm->rts_threshold = BCM43xx_MAX_RTS_THRESHOLD;
err = 0;
@@ -361,7 +364,8 @@
err = 0;
}
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -372,13 +376,12 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
data->rts.value = bcm->rts_threshold;
data->rts.fixed = 0;
data->rts.disabled = (bcm->rts_threshold == BCM43xx_MAX_RTS_THRESHOLD);
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -392,7 +395,8 @@
unsigned long flags;
int err = -EINVAL;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (data->frag.disabled) {
bcm->ieee->fts = MAX_FRAG_THRESHOLD;
err = 0;
@@ -403,7 +407,8 @@
err = 0;
}
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -414,13 +419,12 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
data->frag.value = bcm->ieee->fts;
data->frag.fixed = 0;
data->frag.disabled = (bcm->ieee->fts == MAX_FRAG_THRESHOLD);
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -442,7 +446,8 @@
return -EOPNOTSUPP;
}
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED)
goto out_unlock;
radio = bcm43xx_current_radio(bcm);
@@ -466,7 +471,8 @@
err = 0;
out_unlock:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -478,10 +484,9 @@
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
struct bcm43xx_radioinfo *radio;
- unsigned long flags;
int err = -ENODEV;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
if (bcm43xx_status(bcm) != BCM43xx_STAT_INITIALIZED)
goto out_unlock;
radio = bcm43xx_current_radio(bcm);
@@ -493,7 +498,7 @@
err = 0;
out_unlock:
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -580,7 +585,8 @@
return -EINVAL;
}
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED) {
err = bcm43xx_radio_set_interference_mitigation(bcm, mode);
if (err) {
@@ -595,7 +601,8 @@
} else
bcm43xx_current_radio(bcm)->interfmode = mode;
}
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return err;
}
@@ -606,12 +613,11 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
int mode;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
mode = bcm43xx_current_radio(bcm)->interfmode;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
switch (mode) {
case BCM43xx_RADIO_INTERFMODE_NONE:
@@ -641,9 +647,11 @@
int on;
on = *((int *)extra);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
bcm->short_preamble = !!on;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -654,12 +662,11 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
int on;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
on = bcm->short_preamble;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
if (on)
strncpy(extra, "1 (Short Preamble enabled)", MAX_WX_STRING);
@@ -681,11 +688,13 @@
on = *((int *)extra);
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
bcm->ieee->host_encrypt = !!on;
bcm->ieee->host_decrypt = !!on;
bcm->ieee->host_build_iv = !on;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
return 0;
}
@@ -696,12 +705,11 @@
char *extra)
{
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
- unsigned long flags;
int on;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
on = bcm->ieee->host_encrypt;
- bcm43xx_unlock_irqsafe(bcm, flags);
+ mutex_unlock(&bcm->mutex);
if (on)
strncpy(extra, "1 (SW encryption enabled) ", MAX_WX_STRING);
@@ -764,11 +772,13 @@
if (!sprom)
goto out;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
err = -ENODEV;
if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED)
err = bcm43xx_sprom_read(bcm, sprom);
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
if (!err)
data->data.length = sprom2hex(sprom, extra);
kfree(sprom);
@@ -809,11 +819,15 @@
if (err)
goto out_kfree;
- bcm43xx_lock_irqsafe(bcm, flags);
+ mutex_lock(&bcm->mutex);
+ spin_lock_irqsave(&bcm->irq_lock, flags);
+ spin_lock(&bcm->leds_lock);
err = -ENODEV;
if (bcm43xx_status(bcm) == BCM43xx_STAT_INITIALIZED)
err = bcm43xx_sprom_write(bcm, sprom);
- bcm43xx_unlock_irqsafe(bcm, flags);
+ spin_unlock(&bcm->leds_lock);
+ spin_unlock_irqrestore(&bcm->irq_lock, flags);
+ mutex_unlock(&bcm->mutex);
out_kfree:
kfree(sprom);
out:
@@ -827,6 +841,10 @@
struct bcm43xx_private *bcm = bcm43xx_priv(net_dev);
struct ieee80211softmac_device *mac = ieee80211_priv(net_dev);
struct iw_statistics *wstats;
+ struct ieee80211_network *network = NULL;
+ static int tmp_level = 0;
+ static int tmp_qual = 0;
+ unsigned long flags;
wstats = &bcm->stats.wstats;
if (!mac->associated) {
@@ -844,16 +862,28 @@
wstats->qual.level = 0;
wstats->qual.noise = 0;
wstats->qual.updated = 7;
- wstats->qual.updated |= IW_QUAL_NOISE_INVALID |
- IW_QUAL_QUAL_INVALID | IW_QUAL_LEVEL_INVALID;
+ wstats->qual.updated |= IW_QUAL_ALL_UPDATED | IW_QUAL_DBM;
return wstats;
}
/* fill in the real statistics when iface associated */
- wstats->qual.qual = 100; // TODO: get the real signal quality
- wstats->qual.level = 3 - bcm->stats.link_quality;
+ spin_lock_irqsave(&mac->ieee->lock, flags);
+ list_for_each_entry(network, &mac->ieee->network_list, list) {
+ if (!memcmp(mac->associnfo.bssid, network->bssid, ETH_ALEN)) {
+ if (!tmp_level) { /* get initial values */
+ tmp_level = network->stats.signal;
+ tmp_qual = network->stats.rssi;
+ } else { /* smooth results */
+ tmp_level = (15 * tmp_level + network->stats.signal)/16;
+ tmp_qual = (15 * tmp_qual + network->stats.rssi)/16;
+ }
+ break;
+ }
+ }
+ spin_unlock_irqrestore(&mac->ieee->lock, flags);
+ wstats->qual.level = tmp_level;
+ wstats->qual.qual = 100 * tmp_qual / RX_RSSI_MAX;
wstats->qual.noise = bcm->stats.noise;
- wstats->qual.updated = IW_QUAL_QUAL_UPDATED | IW_QUAL_LEVEL_UPDATED |
- IW_QUAL_NOISE_UPDATED;
+ wstats->qual.updated = IW_QUAL_ALL_UPDATED | IW_QUAL_DBM;
wstats->discard.code = bcm->ieee->ieee_stats.rx_discards_undecryptable;
wstats->discard.retries = bcm->ieee->ieee_stats.tx_retry_limit_exceeded;
wstats->discard.nwid = bcm->ieee->ieee_stats.tx_discards_wrong_sa;
diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_xmit.c b/drivers/net/wireless/bcm43xx/bcm43xx_xmit.c
index 6dbd855..c0efbfe 100644
--- a/drivers/net/wireless/bcm43xx/bcm43xx_xmit.c
+++ b/drivers/net/wireless/bcm43xx/bcm43xx_xmit.c
@@ -492,16 +492,15 @@
memset(&stats, 0, sizeof(stats));
stats.mac_time = le16_to_cpu(rxhdr->mactime);
- stats.rssi = bcm43xx_rssi_postprocess(bcm, rxhdr->rssi, is_ofdm,
+ stats.rssi = rxhdr->rssi;
+ stats.signal = bcm43xx_rssi_postprocess(bcm, rxhdr->rssi, is_ofdm,
!!(rxflags1 & BCM43xx_RXHDR_FLAGS1_2053RSSIADJ),
!!(rxflags3 & BCM43xx_RXHDR_FLAGS3_2050RSSIADJ));
- stats.signal = rxhdr->signal_quality; //FIXME
//TODO stats.noise =
if (is_ofdm)
stats.rate = bcm43xx_plcp_get_bitrate_ofdm(plcp);
else
stats.rate = bcm43xx_plcp_get_bitrate_cck(plcp);
-//printk("RX ofdm %d, rate == %u\n", is_ofdm, stats.rate);
stats.received_channel = radio->channel;
//TODO stats.control =
stats.mask = IEEE80211_STATMASK_SIGNAL |
diff --git a/drivers/net/wireless/ipw2100.c b/drivers/net/wireless/ipw2100.c
index e955db4..5f8ccf4 100644
--- a/drivers/net/wireless/ipw2100.c
+++ b/drivers/net/wireless/ipw2100.c
@@ -6531,7 +6531,7 @@
printk(KERN_INFO DRV_NAME ": %s, %s\n", DRV_DESCRIPTION, DRV_VERSION);
printk(KERN_INFO DRV_NAME ": %s\n", DRV_COPYRIGHT);
- ret = pci_module_init(&ipw2100_pci_driver);
+ ret = pci_register_driver(&ipw2100_pci_driver);
#ifdef CONFIG_IPW2100_DEBUG
ipw2100_debug_level = debug;
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index b3300ff..a72f3e1 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -2667,7 +2667,7 @@
IPW_DEBUG_FW(">> :\n");
- //set the Stop and Abort bit
+ /* set the Stop and Abort bit */
control = DMA_CONTROL_SMALL_CB_CONST_VALUE | DMA_CB_STOP_AND_ABORT;
ipw_write_reg32(priv, IPW_DMA_I_DMA_CONTROL, control);
priv->sram_desc.last_cb_index = 0;
@@ -3002,8 +3002,6 @@
if (rc < 0)
return rc;
-// spin_lock_irqsave(&priv->lock, flags);
-
for (addr = IPW_SHARED_LOWER_BOUND;
addr < IPW_REGISTER_DOMAIN1_END; addr += 4) {
ipw_write32(priv, addr, 0);
@@ -3097,8 +3095,6 @@
firmware have problem getting alive resp. */
ipw_write_reg8(priv, IPW_BASEBAND_CONTROL_STATUS, 0);
-// spin_unlock_irqrestore(&priv->lock, flags);
-
return rc;
}
@@ -6387,13 +6383,6 @@
(wrqu->data.length && extra == NULL))
return -EINVAL;
- //mutex_lock(&priv->mutex);
-
- //if (!ieee->wpa_enabled) {
- // err = -EOPNOTSUPP;
- // goto out;
- //}
-
if (wrqu->data.length) {
buf = kmalloc(wrqu->data.length, GFP_KERNEL);
if (buf == NULL) {
@@ -6413,7 +6402,6 @@
ipw_wpa_assoc_frame(priv, ieee->wpa_ie, ieee->wpa_ie_len);
out:
- //mutex_unlock(&priv->mutex);
return err;
}
@@ -6426,13 +6414,6 @@
struct ieee80211_device *ieee = priv->ieee;
int err = 0;
- //mutex_lock(&priv->mutex);
-
- //if (!ieee->wpa_enabled) {
- // err = -EOPNOTSUPP;
- // goto out;
- //}
-
if (ieee->wpa_ie_len == 0 || ieee->wpa_ie == NULL) {
wrqu->data.length = 0;
goto out;
@@ -6447,7 +6428,6 @@
memcpy(extra, ieee->wpa_ie, ieee->wpa_ie_len);
out:
- //mutex_unlock(&priv->mutex);
return err;
}
@@ -6558,7 +6538,6 @@
ieee->ieee802_1x = param->value;
break;
- //case IW_AUTH_ROAMING_CONTROL:
case IW_AUTH_PRIVACY_INVOKED:
ieee->privacy_invoked = param->value;
break;
@@ -6680,7 +6659,7 @@
switch (mlme->cmd) {
case IW_MLME_DEAUTH:
- // silently ignore
+ /* silently ignore */
break;
case IW_MLME_DISASSOC:
@@ -9766,7 +9745,7 @@
return 0;
}
-#endif // CONFIG_IPW2200_MONITOR
+#endif /* CONFIG_IPW2200_MONITOR */
static int ipw_wx_reset(struct net_device *dev,
struct iw_request_info *info,
@@ -10009,7 +9988,7 @@
sys_config->dot11g_auto_detection = 0;
sys_config->enable_cts_to_self = 0;
sys_config->bt_coexist_collision_thr = 0;
- sys_config->pass_noise_stats_to_host = 1; //1 -- fix for 256
+ sys_config->pass_noise_stats_to_host = 1; /* 1 -- fix for 256 */
sys_config->silence_threshold = 0x1e;
}
@@ -11774,7 +11753,7 @@
printk(KERN_INFO DRV_NAME ": " DRV_DESCRIPTION ", " DRV_VERSION "\n");
printk(KERN_INFO DRV_NAME ": " DRV_COPYRIGHT "\n");
- ret = pci_module_init(&ipw_driver);
+ ret = pci_register_driver(&ipw_driver);
if (ret) {
IPW_ERROR("Unable to initialize PCI module\n");
return ret;
diff --git a/drivers/net/wireless/orinoco_nortel.c b/drivers/net/wireless/orinoco_nortel.c
index bf05b90..eaf3d13 100644
--- a/drivers/net/wireless/orinoco_nortel.c
+++ b/drivers/net/wireless/orinoco_nortel.c
@@ -304,7 +304,7 @@
static int __init orinoco_nortel_init(void)
{
printk(KERN_DEBUG "%s\n", version);
- return pci_module_init(&orinoco_nortel_driver);
+ return pci_register_driver(&orinoco_nortel_driver);
}
static void __exit orinoco_nortel_exit(void)
diff --git a/drivers/net/wireless/orinoco_pci.c b/drivers/net/wireless/orinoco_pci.c
index 1759c54..97a8b4f 100644
--- a/drivers/net/wireless/orinoco_pci.c
+++ b/drivers/net/wireless/orinoco_pci.c
@@ -244,7 +244,7 @@
static int __init orinoco_pci_init(void)
{
printk(KERN_DEBUG "%s\n", version);
- return pci_module_init(&orinoco_pci_driver);
+ return pci_register_driver(&orinoco_pci_driver);
}
static void __exit orinoco_pci_exit(void)
diff --git a/drivers/net/wireless/orinoco_plx.c b/drivers/net/wireless/orinoco_plx.c
index 7f006f6..31162ac 100644
--- a/drivers/net/wireless/orinoco_plx.c
+++ b/drivers/net/wireless/orinoco_plx.c
@@ -351,7 +351,7 @@
static int __init orinoco_plx_init(void)
{
printk(KERN_DEBUG "%s\n", version);
- return pci_module_init(&orinoco_plx_driver);
+ return pci_register_driver(&orinoco_plx_driver);
}
static void __exit orinoco_plx_exit(void)
diff --git a/drivers/net/wireless/orinoco_tmd.c b/drivers/net/wireless/orinoco_tmd.c
index 0831721..7c7b960 100644
--- a/drivers/net/wireless/orinoco_tmd.c
+++ b/drivers/net/wireless/orinoco_tmd.c
@@ -228,7 +228,7 @@
static int __init orinoco_tmd_init(void)
{
printk(KERN_DEBUG "%s\n", version);
- return pci_module_init(&orinoco_tmd_driver);
+ return pci_register_driver(&orinoco_tmd_driver);
}
static void __exit orinoco_tmd_exit(void)
diff --git a/drivers/net/wireless/prism54/isl_ioctl.c b/drivers/net/wireless/prism54/isl_ioctl.c
index 989599a..0c30fe7 100644
--- a/drivers/net/wireless/prism54/isl_ioctl.c
+++ b/drivers/net/wireless/prism54/isl_ioctl.c
@@ -35,10 +35,14 @@
#include <net/iw_handler.h> /* New driver API */
+#define KEY_SIZE_WEP104 13 /* 104/128-bit WEP keys */
+#define KEY_SIZE_WEP40 5 /* 40/64-bit WEP keys */
+/* KEY_SIZE_TKIP should match isl_oid.h, struct obj_key.key[] size */
+#define KEY_SIZE_TKIP 32 /* TKIP keys */
-static void prism54_wpa_ie_add(islpci_private *priv, u8 *bssid,
+static void prism54_wpa_bss_ie_add(islpci_private *priv, u8 *bssid,
u8 *wpa_ie, size_t wpa_ie_len);
-static size_t prism54_wpa_ie_get(islpci_private *priv, u8 *bssid, u8 *wpa_ie);
+static size_t prism54_wpa_bss_ie_get(islpci_private *priv, u8 *bssid, u8 *wpa_ie);
static int prism54_set_wpa(struct net_device *, struct iw_request_info *,
__u32 *, char *);
@@ -468,6 +472,9 @@
range->event_capa[1] = IW_EVENT_CAPA_K_1;
range->event_capa[4] = IW_EVENT_CAPA_MASK(IWEVCUSTOM);
+ range->enc_capa = IW_ENC_CAPA_WPA | IW_ENC_CAPA_WPA2 |
+ IW_ENC_CAPA_CIPHER_TKIP;
+
if (islpci_get_state(priv) < PRV_STATE_INIT)
return 0;
@@ -567,6 +574,8 @@
struct iw_event iwe; /* Temporary buffer */
short cap;
islpci_private *priv = netdev_priv(ndev);
+ u8 wpa_ie[MAX_WPA_IE_LEN];
+ size_t wpa_ie_len;
/* The first entry must be the MAC address */
memcpy(iwe.u.ap_addr.sa_data, bss->address, 6);
@@ -627,27 +636,13 @@
current_ev =
iwe_stream_add_event(current_ev, end_buf, &iwe, IW_EV_QUAL_LEN);
- if (priv->wpa) {
- u8 wpa_ie[MAX_WPA_IE_LEN];
- char *buf, *p;
- size_t wpa_ie_len;
- int i;
-
- wpa_ie_len = prism54_wpa_ie_get(priv, bss->address, wpa_ie);
- if (wpa_ie_len > 0 &&
- (buf = kmalloc(wpa_ie_len * 2 + 10, GFP_ATOMIC))) {
- p = buf;
- p += sprintf(p, "wpa_ie=");
- for (i = 0; i < wpa_ie_len; i++) {
- p += sprintf(p, "%02x", wpa_ie[i]);
- }
- memset(&iwe, 0, sizeof (iwe));
- iwe.cmd = IWEVCUSTOM;
- iwe.u.data.length = strlen(buf);
- current_ev = iwe_stream_add_point(current_ev, end_buf,
- &iwe, buf);
- kfree(buf);
- }
+ /* Add WPA/RSN Information Element, if any */
+ wpa_ie_len = prism54_wpa_bss_ie_get(priv, bss->address, wpa_ie);
+ if (wpa_ie_len > 0) {
+ iwe.cmd = IWEVGENIE;
+ iwe.u.data.length = min(wpa_ie_len, (size_t)MAX_WPA_IE_LEN);
+ current_ev = iwe_stream_add_point(current_ev, end_buf,
+ &iwe, wpa_ie);
}
return current_ev;
}
@@ -1051,12 +1046,24 @@
current_index = r.u;
/* Verify that the key is not marked as invalid */
if (!(dwrq->flags & IW_ENCODE_NOKEY)) {
- key.length = dwrq->length > sizeof (key.key) ?
- sizeof (key.key) : dwrq->length;
- memcpy(key.key, extra, key.length);
- if (key.length == 32)
- /* we want WPA-PSK */
+ if (dwrq->length > KEY_SIZE_TKIP) {
+ /* User-provided key data too big */
+ return -EINVAL;
+ }
+ if (dwrq->length > KEY_SIZE_WEP104) {
+ /* WPA-PSK TKIP */
key.type = DOT11_PRIV_TKIP;
+ key.length = KEY_SIZE_TKIP;
+ } else if (dwrq->length > KEY_SIZE_WEP40) {
+ /* WEP 104/128 */
+ key.length = KEY_SIZE_WEP104;
+ } else {
+ /* WEP 40/64 */
+ key.length = KEY_SIZE_WEP40;
+ }
+ memset(key.key, 0, sizeof (key.key));
+ memcpy(key.key, extra, dwrq->length);
+
if ((index < 0) || (index > 3))
/* no index provided use the current one */
index = current_index;
@@ -1210,6 +1217,489 @@
}
}
+static int prism54_set_genie(struct net_device *ndev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ int alen, ret = 0;
+ struct obj_attachment *attach;
+
+ if (data->length > MAX_WPA_IE_LEN ||
+ (data->length && extra == NULL))
+ return -EINVAL;
+
+ memcpy(priv->wpa_ie, extra, data->length);
+ priv->wpa_ie_len = data->length;
+
+ alen = sizeof(*attach) + priv->wpa_ie_len;
+ attach = kzalloc(alen, GFP_KERNEL);
+ if (attach == NULL)
+ return -ENOMEM;
+
+#define WLAN_FC_TYPE_MGMT 0
+#define WLAN_FC_STYPE_ASSOC_REQ 0
+#define WLAN_FC_STYPE_REASSOC_REQ 2
+
+ /* Note: endianness is covered by mgt_set_varlen */
+ attach->type = (WLAN_FC_TYPE_MGMT << 2) |
+ (WLAN_FC_STYPE_ASSOC_REQ << 4);
+ attach->id = -1;
+ attach->size = priv->wpa_ie_len;
+ memcpy(attach->data, extra, priv->wpa_ie_len);
+
+ ret = mgt_set_varlen(priv, DOT11_OID_ATTACHMENT, attach,
+ priv->wpa_ie_len);
+ if (ret == 0) {
+ attach->type = (WLAN_FC_TYPE_MGMT << 2) |
+ (WLAN_FC_STYPE_REASSOC_REQ << 4);
+
+ ret = mgt_set_varlen(priv, DOT11_OID_ATTACHMENT, attach,
+ priv->wpa_ie_len);
+ if (ret == 0)
+ printk(KERN_DEBUG "%s: WPA IE Attachment was set\n",
+ ndev->name);
+ }
+
+ kfree(attach);
+ return ret;
+}
+
+
+static int prism54_get_genie(struct net_device *ndev,
+ struct iw_request_info *info,
+ struct iw_point *data, char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ int len = priv->wpa_ie_len;
+
+ if (len <= 0) {
+ data->length = 0;
+ return 0;
+ }
+
+ if (data->length < len)
+ return -E2BIG;
+
+ data->length = len;
+ memcpy(extra, priv->wpa_ie, len);
+
+ return 0;
+}
+
+static int prism54_set_auth(struct net_device *ndev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu, char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ struct iw_param *param = &wrqu->param;
+ u32 mlmelevel = 0, authen = 0, dot1x = 0;
+ u32 exunencrypt = 0, privinvoked = 0, wpa = 0;
+ u32 old_wpa;
+ int ret = 0;
+ union oid_res_t r;
+
+ if (islpci_get_state(priv) < PRV_STATE_INIT)
+ return 0;
+
+ /* first get the flags */
+ down_write(&priv->mib_sem);
+ wpa = old_wpa = priv->wpa;
+ up_write(&priv->mib_sem);
+ ret = mgt_get_request(priv, DOT11_OID_AUTHENABLE, 0, NULL, &r);
+ authen = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_PRIVACYINVOKED, 0, NULL, &r);
+ privinvoked = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_EXUNENCRYPTED, 0, NULL, &r);
+ exunencrypt = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_DOT1XENABLE, 0, NULL, &r);
+ dot1x = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_MLMEAUTOLEVEL, 0, NULL, &r);
+ mlmelevel = r.u;
+
+ if (ret < 0)
+ goto out;
+
+ switch (param->flags & IW_AUTH_INDEX) {
+ case IW_AUTH_CIPHER_PAIRWISE:
+ case IW_AUTH_CIPHER_GROUP:
+ case IW_AUTH_KEY_MGMT:
+ break;
+
+ case IW_AUTH_WPA_ENABLED:
+ /* Do the same thing as IW_AUTH_WPA_VERSION */
+ if (param->value) {
+ wpa = 1;
+ privinvoked = 1; /* For privacy invoked */
+ exunencrypt = 1; /* Filter out all unencrypted frames */
+ dot1x = 0x01; /* To enable eap filter */
+ mlmelevel = DOT11_MLME_EXTENDED;
+ authen = DOT11_AUTH_OS; /* Only WEP uses _SK and _BOTH */
+ } else {
+ wpa = 0;
+ privinvoked = 0;
+ exunencrypt = 0; /* Do not filter un-encrypted data */
+ dot1x = 0;
+ mlmelevel = DOT11_MLME_AUTO;
+ }
+ break;
+
+ case IW_AUTH_WPA_VERSION:
+ if (param->value & IW_AUTH_WPA_VERSION_DISABLED) {
+ wpa = 0;
+ privinvoked = 0;
+ exunencrypt = 0; /* Do not filter un-encrypted data */
+ dot1x = 0;
+ mlmelevel = DOT11_MLME_AUTO;
+ } else {
+ if (param->value & IW_AUTH_WPA_VERSION_WPA)
+ wpa = 1;
+ else if (param->value & IW_AUTH_WPA_VERSION_WPA2)
+ wpa = 2;
+ privinvoked = 1; /* For privacy invoked */
+ exunencrypt = 1; /* Filter out all unencrypted frames */
+ dot1x = 0x01; /* To enable eap filter */
+ mlmelevel = DOT11_MLME_EXTENDED;
+ authen = DOT11_AUTH_OS; /* Only WEP uses _SK and _BOTH */
+ }
+ break;
+
+ case IW_AUTH_RX_UNENCRYPTED_EAPOL:
+ dot1x = param->value ? 1 : 0;
+ break;
+
+ case IW_AUTH_PRIVACY_INVOKED:
+ privinvoked = param->value ? 1 : 0;
+
+ case IW_AUTH_DROP_UNENCRYPTED:
+ exunencrypt = param->value ? 1 : 0;
+ break;
+
+ case IW_AUTH_80211_AUTH_ALG:
+ if (param->value & IW_AUTH_ALG_SHARED_KEY) {
+ /* Only WEP uses _SK and _BOTH */
+ if (wpa > 0) {
+ ret = -EINVAL;
+ goto out;
+ }
+ authen = DOT11_AUTH_SK;
+ } else if (param->value & IW_AUTH_ALG_OPEN_SYSTEM) {
+ authen = DOT11_AUTH_OS;
+ } else {
+ ret = -EINVAL;
+ goto out;
+ }
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ /* Set all the values */
+ down_write(&priv->mib_sem);
+ priv->wpa = wpa;
+ up_write(&priv->mib_sem);
+ mgt_set_request(priv, DOT11_OID_AUTHENABLE, 0, &authen);
+ mgt_set_request(priv, DOT11_OID_PRIVACYINVOKED, 0, &privinvoked);
+ mgt_set_request(priv, DOT11_OID_EXUNENCRYPTED, 0, &exunencrypt);
+ mgt_set_request(priv, DOT11_OID_DOT1XENABLE, 0, &dot1x);
+ mgt_set_request(priv, DOT11_OID_MLMEAUTOLEVEL, 0, &mlmelevel);
+
+out:
+ return ret;
+}
+
+static int prism54_get_auth(struct net_device *ndev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu, char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ struct iw_param *param = &wrqu->param;
+ u32 wpa = 0;
+ int ret = 0;
+ union oid_res_t r;
+
+ if (islpci_get_state(priv) < PRV_STATE_INIT)
+ return 0;
+
+ /* first get the flags */
+ down_write(&priv->mib_sem);
+ wpa = priv->wpa;
+ up_write(&priv->mib_sem);
+
+ switch (param->flags & IW_AUTH_INDEX) {
+ case IW_AUTH_CIPHER_PAIRWISE:
+ case IW_AUTH_CIPHER_GROUP:
+ case IW_AUTH_KEY_MGMT:
+ /*
+ * wpa_supplicant will control these internally
+ */
+ ret = -EOPNOTSUPP;
+ break;
+
+ case IW_AUTH_WPA_VERSION:
+ switch (wpa) {
+ case 1:
+ param->value = IW_AUTH_WPA_VERSION_WPA;
+ break;
+ case 2:
+ param->value = IW_AUTH_WPA_VERSION_WPA2;
+ break;
+ case 0:
+ default:
+ param->value = IW_AUTH_WPA_VERSION_DISABLED;
+ break;
+ }
+ break;
+
+ case IW_AUTH_DROP_UNENCRYPTED:
+ ret = mgt_get_request(priv, DOT11_OID_EXUNENCRYPTED, 0, NULL, &r);
+ if (ret >= 0)
+ param->value = r.u > 0 ? 1 : 0;
+ break;
+
+ case IW_AUTH_80211_AUTH_ALG:
+ ret = mgt_get_request(priv, DOT11_OID_AUTHENABLE, 0, NULL, &r);
+ if (ret >= 0) {
+ switch (r.u) {
+ case DOT11_AUTH_OS:
+ param->value = IW_AUTH_ALG_OPEN_SYSTEM;
+ break;
+ case DOT11_AUTH_BOTH:
+ case DOT11_AUTH_SK:
+ param->value = IW_AUTH_ALG_SHARED_KEY;
+ case DOT11_AUTH_NONE:
+ default:
+ param->value = 0;
+ break;
+ }
+ }
+ break;
+
+ case IW_AUTH_WPA_ENABLED:
+ param->value = wpa > 0 ? 1 : 0;
+ break;
+
+ case IW_AUTH_RX_UNENCRYPTED_EAPOL:
+ ret = mgt_get_request(priv, DOT11_OID_DOT1XENABLE, 0, NULL, &r);
+ if (ret >= 0)
+ param->value = r.u > 0 ? 1 : 0;
+ break;
+
+ case IW_AUTH_PRIVACY_INVOKED:
+ ret = mgt_get_request(priv, DOT11_OID_PRIVACYINVOKED, 0, NULL, &r);
+ if (ret >= 0)
+ param->value = r.u > 0 ? 1 : 0;
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+ return ret;
+}
+
+static int prism54_set_encodeext(struct net_device *ndev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ struct iw_point *encoding = &wrqu->encoding;
+ struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
+ int idx, alg = ext->alg, set_key = 1;
+ union oid_res_t r;
+ int authen = DOT11_AUTH_OS, invoke = 0, exunencrypt = 0;
+ int ret = 0;
+
+ if (islpci_get_state(priv) < PRV_STATE_INIT)
+ return 0;
+
+ /* Determine and validate the key index */
+ idx = (encoding->flags & IW_ENCODE_INDEX) - 1;
+ if (idx) {
+ if (idx < 0 || idx > 3)
+ return -EINVAL;
+ } else {
+ ret = mgt_get_request(priv, DOT11_OID_DEFKEYID, 0, NULL, &r);
+ if (ret < 0)
+ goto out;
+ idx = r.u;
+ }
+
+ if (encoding->flags & IW_ENCODE_DISABLED)
+ alg = IW_ENCODE_ALG_NONE;
+
+ if (ext->ext_flags & IW_ENCODE_EXT_SET_TX_KEY) {
+ /* Only set transmit key index here, actual
+ * key is set below if needed.
+ */
+ ret = mgt_set_request(priv, DOT11_OID_DEFKEYID, 0, &idx);
+ set_key = ext->key_len > 0 ? 1 : 0;
+ }
+
+ if (set_key) {
+ struct obj_key key = { DOT11_PRIV_WEP, 0, "" };
+ switch (alg) {
+ case IW_ENCODE_ALG_NONE:
+ break;
+ case IW_ENCODE_ALG_WEP:
+ if (ext->key_len > KEY_SIZE_WEP104) {
+ ret = -EINVAL;
+ goto out;
+ }
+ if (ext->key_len > KEY_SIZE_WEP40)
+ key.length = KEY_SIZE_WEP104;
+ else
+ key.length = KEY_SIZE_WEP40;
+ break;
+ case IW_ENCODE_ALG_TKIP:
+ if (ext->key_len > KEY_SIZE_TKIP) {
+ ret = -EINVAL;
+ goto out;
+ }
+ key.type = DOT11_PRIV_TKIP;
+ key.length = KEY_SIZE_TKIP;
+ default:
+ return -EINVAL;
+ }
+
+ if (key.length) {
+ memset(key.key, 0, sizeof(key.key));
+ memcpy(key.key, ext->key, ext->key_len);
+ ret = mgt_set_request(priv, DOT11_OID_DEFKEYX, idx,
+ &key);
+ if (ret < 0)
+ goto out;
+ }
+ }
+
+ /* Read the flags */
+ if (encoding->flags & IW_ENCODE_DISABLED) {
+ /* Encoding disabled,
+ * authen = DOT11_AUTH_OS;
+ * invoke = 0;
+ * exunencrypt = 0; */
+ }
+ if (encoding->flags & IW_ENCODE_OPEN) {
+ /* Encode but accept non-encoded packets. No auth */
+ invoke = 1;
+ }
+ if (encoding->flags & IW_ENCODE_RESTRICTED) {
+ /* Refuse non-encoded packets. Auth */
+ authen = DOT11_AUTH_BOTH;
+ invoke = 1;
+ exunencrypt = 1;
+ }
+
+ /* do the change if requested */
+ if (encoding->flags & IW_ENCODE_MODE) {
+ ret = mgt_set_request(priv, DOT11_OID_AUTHENABLE, 0,
+ &authen);
+ ret = mgt_set_request(priv, DOT11_OID_PRIVACYINVOKED, 0,
+ &invoke);
+ ret = mgt_set_request(priv, DOT11_OID_EXUNENCRYPTED, 0,
+ &exunencrypt);
+ }
+
+out:
+ return ret;
+}
+
+
+static int prism54_get_encodeext(struct net_device *ndev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ islpci_private *priv = netdev_priv(ndev);
+ struct iw_point *encoding = &wrqu->encoding;
+ struct iw_encode_ext *ext = (struct iw_encode_ext *)extra;
+ int idx, max_key_len;
+ union oid_res_t r;
+ int authen = DOT11_AUTH_OS, invoke = 0, exunencrypt = 0, wpa = 0;
+ int ret = 0;
+
+ if (islpci_get_state(priv) < PRV_STATE_INIT)
+ return 0;
+
+ /* first get the flags */
+ ret = mgt_get_request(priv, DOT11_OID_AUTHENABLE, 0, NULL, &r);
+ authen = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_PRIVACYINVOKED, 0, NULL, &r);
+ invoke = r.u;
+ ret = mgt_get_request(priv, DOT11_OID_EXUNENCRYPTED, 0, NULL, &r);
+ exunencrypt = r.u;
+ if (ret < 0)
+ goto out;
+
+ max_key_len = encoding->length - sizeof(*ext);
+ if (max_key_len < 0)
+ return -EINVAL;
+
+ idx = (encoding->flags & IW_ENCODE_INDEX) - 1;
+ if (idx) {
+ if (idx < 0 || idx > 3)
+ return -EINVAL;
+ } else {
+ ret = mgt_get_request(priv, DOT11_OID_DEFKEYID, 0, NULL, &r);
+ if (ret < 0)
+ goto out;
+ idx = r.u;
+ }
+
+ encoding->flags = idx + 1;
+ memset(ext, 0, sizeof(*ext));
+
+ switch (authen) {
+ case DOT11_AUTH_BOTH:
+ case DOT11_AUTH_SK:
+ wrqu->encoding.flags |= IW_ENCODE_RESTRICTED;
+ case DOT11_AUTH_OS:
+ default:
+ wrqu->encoding.flags |= IW_ENCODE_OPEN;
+ break;
+ }
+
+ down_write(&priv->mib_sem);
+ wpa = priv->wpa;
+ up_write(&priv->mib_sem);
+
+ if (authen == DOT11_AUTH_OS && !exunencrypt && !invoke && !wpa) {
+ /* No encryption */
+ ext->alg = IW_ENCODE_ALG_NONE;
+ ext->key_len = 0;
+ wrqu->encoding.flags |= IW_ENCODE_DISABLED;
+ } else {
+ struct obj_key *key;
+
+ ret = mgt_get_request(priv, DOT11_OID_DEFKEYX, idx, NULL, &r);
+ if (ret < 0)
+ goto out;
+ key = r.ptr;
+ if (max_key_len < key->length) {
+ ret = -E2BIG;
+ goto out;
+ }
+ memcpy(ext->key, key->key, key->length);
+ ext->key_len = key->length;
+
+ switch (key->type) {
+ case DOT11_PRIV_TKIP:
+ ext->alg = IW_ENCODE_ALG_TKIP;
+ break;
+ default:
+ case DOT11_PRIV_WEP:
+ ext->alg = IW_ENCODE_ALG_WEP;
+ break;
+ }
+ wrqu->encoding.flags |= IW_ENCODE_ENABLED;
+ }
+
+out:
+ return ret;
+}
+
+
static int
prism54_reset(struct net_device *ndev, struct iw_request_info *info,
__u32 * uwrq, char *extra)
@@ -1591,8 +2081,8 @@
#define MACSTR "%02x:%02x:%02x:%02x:%02x:%02x"
static void
-prism54_wpa_ie_add(islpci_private *priv, u8 *bssid,
- u8 *wpa_ie, size_t wpa_ie_len)
+prism54_wpa_bss_ie_add(islpci_private *priv, u8 *bssid,
+ u8 *wpa_ie, size_t wpa_ie_len)
{
struct list_head *ptr;
struct islpci_bss_wpa_ie *bss = NULL;
@@ -1658,7 +2148,7 @@
}
static size_t
-prism54_wpa_ie_get(islpci_private *priv, u8 *bssid, u8 *wpa_ie)
+prism54_wpa_bss_ie_get(islpci_private *priv, u8 *bssid, u8 *wpa_ie)
{
struct list_head *ptr;
struct islpci_bss_wpa_ie *bss = NULL;
@@ -1683,14 +2173,14 @@
}
void
-prism54_wpa_ie_init(islpci_private *priv)
+prism54_wpa_bss_ie_init(islpci_private *priv)
{
INIT_LIST_HEAD(&priv->bss_wpa_list);
sema_init(&priv->wpa_sem, 1);
}
void
-prism54_wpa_ie_clean(islpci_private *priv)
+prism54_wpa_bss_ie_clean(islpci_private *priv)
{
struct list_head *ptr, *n;
@@ -1722,7 +2212,7 @@
}
if (pos[0] == WLAN_EID_GENERIC && pos[1] >= 4 &&
memcmp(pos + 2, wpa_oid, 4) == 0) {
- prism54_wpa_ie_add(priv, addr, pos, pos[1] + 2);
+ prism54_wpa_bss_ie_add(priv, addr, pos, pos[1] + 2);
return;
}
pos += 2 + pos[1];
@@ -1879,7 +2369,7 @@
send_formatted_event(priv, "Associate request (ex)", mlme, 1);
if (priv->iw_mode != IW_MODE_MASTER
- && mlmeex->state != DOT11_STATE_AUTHING)
+ && mlmeex->state != DOT11_STATE_ASSOCING)
break;
confirm = kmalloc(sizeof(struct obj_mlmeex), GFP_ATOMIC);
@@ -1893,7 +2383,7 @@
confirm->state = 0; /* not used */
confirm->code = 0;
- wpa_ie_len = prism54_wpa_ie_get(priv, mlmeex->address, wpa_ie);
+ wpa_ie_len = prism54_wpa_bss_ie_get(priv, mlmeex->address, wpa_ie);
if (!wpa_ie_len) {
printk(KERN_DEBUG "No WPA IE found from "
@@ -1937,7 +2427,7 @@
confirm->state = 0; /* not used */
confirm->code = 0;
- wpa_ie_len = prism54_wpa_ie_get(priv, mlmeex->address, wpa_ie);
+ wpa_ie_len = prism54_wpa_bss_ie_get(priv, mlmeex->address, wpa_ie);
if (!wpa_ie_len) {
printk(KERN_DEBUG "No WPA IE found from "
@@ -2553,6 +3043,15 @@
(iw_handler) prism54_get_encode, /* SIOCGIWENCODE */
(iw_handler) NULL, /* SIOCSIWPOWER */
(iw_handler) NULL, /* SIOCGIWPOWER */
+ NULL, /* -- hole -- */
+ NULL, /* -- hole -- */
+ (iw_handler) prism54_set_genie, /* SIOCSIWGENIE */
+ (iw_handler) prism54_get_genie, /* SIOCGIWGENIE */
+ (iw_handler) prism54_set_auth, /* SIOCSIWAUTH */
+ (iw_handler) prism54_get_auth, /* SIOCGIWAUTH */
+ (iw_handler) prism54_set_encodeext, /* SIOCSIWENCODEEXT */
+ (iw_handler) prism54_get_encodeext, /* SIOCGIWENCODEEXT */
+ NULL, /* SIOCSIWPMKSA */
};
/* The low order bit identify a SET (0) or a GET (1) ioctl. */
diff --git a/drivers/net/wireless/prism54/isl_ioctl.h b/drivers/net/wireless/prism54/isl_ioctl.h
index 46d5cde..65f33ac 100644
--- a/drivers/net/wireless/prism54/isl_ioctl.h
+++ b/drivers/net/wireless/prism54/isl_ioctl.h
@@ -27,7 +27,7 @@
#include <net/iw_handler.h> /* New driver API */
-#define SUPPORTED_WIRELESS_EXT 16
+#define SUPPORTED_WIRELESS_EXT 19
void prism54_mib_init(islpci_private *);
@@ -39,8 +39,8 @@
void prism54_process_trap(void *);
-void prism54_wpa_ie_init(islpci_private *priv);
-void prism54_wpa_ie_clean(islpci_private *priv);
+void prism54_wpa_bss_ie_init(islpci_private *priv);
+void prism54_wpa_bss_ie_clean(islpci_private *priv);
int prism54_set_mac_address(struct net_device *, void *);
diff --git a/drivers/net/wireless/prism54/islpci_dev.c b/drivers/net/wireless/prism54/islpci_dev.c
index 5ddf295..ab3c5a2 100644
--- a/drivers/net/wireless/prism54/islpci_dev.c
+++ b/drivers/net/wireless/prism54/islpci_dev.c
@@ -715,7 +715,7 @@
}
prism54_acl_init(&priv->acl);
- prism54_wpa_ie_init(priv);
+ prism54_wpa_bss_ie_init(priv);
if (mgt_init(priv))
goto out_free;
@@ -774,7 +774,7 @@
/* Free the acces control list and the WPA list */
prism54_acl_clean(&priv->acl);
- prism54_wpa_ie_clean(priv);
+ prism54_wpa_bss_ie_clean(priv);
mgt_clean(priv);
return 0;
diff --git a/drivers/net/wireless/prism54/islpci_dev.h b/drivers/net/wireless/prism54/islpci_dev.h
index 0705316..5049f37 100644
--- a/drivers/net/wireless/prism54/islpci_dev.h
+++ b/drivers/net/wireless/prism54/islpci_dev.h
@@ -179,6 +179,8 @@
struct list_head bss_wpa_list;
int num_bss_wpa;
struct semaphore wpa_sem;
+ u8 wpa_ie[MAX_WPA_IE_LEN];
+ size_t wpa_ie_len;
struct work_struct reset_task;
int reset_task_pending;
diff --git a/drivers/net/wireless/prism54/islpci_hotplug.c b/drivers/net/wireless/prism54/islpci_hotplug.c
index 09fc17a..f692dcc 100644
--- a/drivers/net/wireless/prism54/islpci_hotplug.c
+++ b/drivers/net/wireless/prism54/islpci_hotplug.c
@@ -313,7 +313,7 @@
__bug_on_wrong_struct_sizes ();
- return pci_module_init(&prism54_driver);
+ return pci_register_driver(&prism54_driver);
}
/* by the time prism54_module_exit() terminates, as a postcondition
diff --git a/drivers/net/wireless/ray_cs.c b/drivers/net/wireless/ray_cs.c
index 61b83a5..8e112d1 100644
--- a/drivers/net/wireless/ray_cs.c
+++ b/drivers/net/wireless/ray_cs.c
@@ -52,8 +52,8 @@
#include <pcmcia/ds.h>
#include <pcmcia/mem_op.h>
-#include <net/ieee80211.h>
#include <linux/wireless.h>
+#include <net/iw_handler.h>
#include <asm/io.h>
#include <asm/system.h>
diff --git a/drivers/net/wireless/zd1211rw/Makefile b/drivers/net/wireless/zd1211rw/Makefile
index 500314f..6603ad5 100644
--- a/drivers/net/wireless/zd1211rw/Makefile
+++ b/drivers/net/wireless/zd1211rw/Makefile
@@ -3,6 +3,7 @@
zd1211rw-objs := zd_chip.o zd_ieee80211.o \
zd_mac.o zd_netdev.o \
zd_rf_al2230.o zd_rf_rf2959.o \
+ zd_rf_al7230b.o \
zd_rf.o zd_usb.o zd_util.o
ifeq ($(CONFIG_ZD1211RW_DEBUG),y)
diff --git a/drivers/net/wireless/zd1211rw/zd_chip.c b/drivers/net/wireless/zd1211rw/zd_chip.c
index da9d06b..5841998 100644
--- a/drivers/net/wireless/zd1211rw/zd_chip.c
+++ b/drivers/net/wireless/zd1211rw/zd_chip.c
@@ -42,12 +42,11 @@
void zd_chip_clear(struct zd_chip *chip)
{
- mutex_lock(&chip->mutex);
+ ZD_ASSERT(!mutex_is_locked(&chip->mutex));
zd_usb_clear(&chip->usb);
zd_rf_clear(&chip->rf);
- mutex_unlock(&chip->mutex);
mutex_destroy(&chip->mutex);
- memset(chip, 0, sizeof(*chip));
+ ZD_MEMCLEAR(chip, sizeof(*chip));
}
static int scnprint_mac_oui(const u8 *addr, char *buffer, size_t size)
@@ -68,10 +67,11 @@
i += scnprint_mac_oui(chip->e2p_mac, buffer+i, size-i);
i += scnprintf(buffer+i, size-i, " ");
i += zd_rf_scnprint_id(&chip->rf, buffer+i, size-i);
- i += scnprintf(buffer+i, size-i, " pa%1x %c%c%c", chip->pa_type,
+ i += scnprintf(buffer+i, size-i, " pa%1x %c%c%c%c", chip->pa_type,
chip->patch_cck_gain ? 'g' : '-',
chip->patch_cr157 ? '7' : '-',
- chip->patch_6m_band_edge ? '6' : '-');
+ chip->patch_6m_band_edge ? '6' : '-',
+ chip->new_phy_layout ? 'N' : '-');
return i;
}
@@ -330,13 +330,14 @@
chip->patch_cck_gain = (value >> 8) & 0x1;
chip->patch_cr157 = (value >> 13) & 0x1;
chip->patch_6m_band_edge = (value >> 21) & 0x1;
+ chip->new_phy_layout = (value >> 31) & 0x1;
dev_dbg_f(zd_chip_dev(chip),
"RF %s %#01x PA type %#01x patch CCK %d patch CR157 %d "
- "patch 6M %d\n",
+ "patch 6M %d new PHY %d\n",
zd_rf_name(*rf_type), *rf_type,
chip->pa_type, chip->patch_cck_gain,
- chip->patch_cr157, chip->patch_6m_band_edge);
+ chip->patch_cr157, chip->patch_6m_band_edge, chip->new_phy_layout);
return 0;
error:
*rf_type = 0;
@@ -344,6 +345,7 @@
chip->patch_cck_gain = 0;
chip->patch_cr157 = 0;
chip->patch_6m_band_edge = 0;
+ chip->new_phy_layout = 0;
return r;
}
@@ -717,7 +719,7 @@
{ CR21, 0x0e }, { CR22, 0x23 }, { CR23, 0x90 },
{ CR24, 0x14 }, { CR25, 0x40 }, { CR26, 0x10 },
{ CR27, 0x10 }, { CR28, 0x7f }, { CR29, 0x80 },
- { CR30, 0x49 }, /* jointly decoder, no ASIC */
+ { CR30, 0x4b }, /* ASIC/FWT, no jointly decoder */
{ CR31, 0x60 }, { CR32, 0x43 }, { CR33, 0x08 },
{ CR34, 0x06 }, { CR35, 0x0a }, { CR36, 0x00 },
{ CR37, 0x00 }, { CR38, 0x38 }, { CR39, 0x0c },
@@ -807,7 +809,6 @@
{ CR_ACK_TIMEOUT_EXT, 0x80 },
{ CR_ADDA_PWR_DWN, 0x00 },
{ CR_ACK_TIME_80211, 0x100 },
- { CR_IFS_VALUE, 0x547c032 },
{ CR_RX_PE_DELAY, 0x70 },
{ CR_PS_CTRL, 0x10000000 },
{ CR_RTS_CTS_RATE, 0x02030203 },
@@ -854,11 +855,10 @@
{ CR_ACK_TIMEOUT_EXT, 0x80 },
{ CR_ADDA_PWR_DWN, 0x00 },
{ CR_ACK_TIME_80211, 0x100 },
- { CR_IFS_VALUE, 0x547c032 },
{ CR_RX_PE_DELAY, 0x70 },
{ CR_PS_CTRL, 0x10000000 },
{ CR_RTS_CTS_RATE, 0x02030203 },
- { CR_RX_THRESHOLD, 0x000c0640 },
+ { CR_RX_THRESHOLD, 0x000c0eff, },
{ CR_AFTER_PNP, 0x1 },
{ CR_WEP_PROTECT, 0x114 },
};
@@ -970,10 +970,15 @@
r = hw_init_hmac(chip);
if (r)
return r;
- r = set_beacon_interval(chip, 100);
+
+ /* Although the vendor driver defaults to a different value during
+ * init, it overwrites the IFS value with the following every time
+ * the channel changes. We should aim to be more intelligent... */
+ r = zd_iowrite32_locked(chip, IFS_VALUE_DEFAULT, CR_IFS_VALUE);
if (r)
return r;
- return 0;
+
+ return set_beacon_interval(chip, 100);
}
#ifdef DEBUG
@@ -1613,3 +1618,34 @@
return 0;
}
+
+/*
+ * We can optionally program the RF directly through CR regs, if supported by
+ * the hardware. This is much faster than the older method.
+ */
+int zd_rfwrite_cr_locked(struct zd_chip *chip, u32 value)
+{
+ struct zd_ioreq16 ioreqs[] = {
+ { CR244, (value >> 16) & 0xff },
+ { CR243, (value >> 8) & 0xff },
+ { CR242, value & 0xff },
+ };
+ ZD_ASSERT(mutex_is_locked(&chip->mutex));
+ return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs));
+}
+
+int zd_rfwritev_cr_locked(struct zd_chip *chip,
+ const u32 *values, unsigned int count)
+{
+ int r;
+ unsigned int i;
+
+ for (i = 0; i < count; i++) {
+ r = zd_rfwrite_cr_locked(chip, values[i]);
+ if (r)
+ return r;
+ }
+
+ return 0;
+}
+
diff --git a/drivers/net/wireless/zd1211rw/zd_chip.h b/drivers/net/wireless/zd1211rw/zd_chip.h
index 069d2b4..4b12508 100644
--- a/drivers/net/wireless/zd1211rw/zd_chip.h
+++ b/drivers/net/wireless/zd1211rw/zd_chip.h
@@ -473,7 +473,15 @@
#define CR_ACK_TIMEOUT_EXT CTL_REG(0x0690)
#define CR_BCN_FIFO_SEMAPHORE CTL_REG(0x0694)
+
#define CR_IFS_VALUE CTL_REG(0x0698)
+#define IFS_VALUE_DIFS_SH 0
+#define IFS_VALUE_EIFS_SH 12
+#define IFS_VALUE_SIFS_SH 24
+#define IFS_VALUE_DEFAULT (( 50 << IFS_VALUE_DIFS_SH) | \
+ (1148 << IFS_VALUE_EIFS_SH) | \
+ ( 10 << IFS_VALUE_SIFS_SH))
+
#define CR_RX_TIME_OUT CTL_REG(0x069C)
#define CR_TOTAL_RX_FRM CTL_REG(0x06A0)
#define CR_CRC32_CNT CTL_REG(0x06A4)
@@ -630,6 +638,7 @@
LOAD_CODE_SIZE = 0xe, /* words */
LOAD_VECT_SIZE = 0x10000 - 0xfff7, /* words */
EEPROM_REGS_OFFSET = LOAD_CODE_SIZE + LOAD_VECT_SIZE,
+ EEPROM_REGS_SIZE = 0x7e, /* words */
E2P_BASE_OFFSET = EEPROM_START_OFFSET +
EEPROM_REGS_OFFSET,
};
@@ -655,7 +664,7 @@
/* SetPointOFDM in the vendor driver */
u8 ofdm_cal_values[3][E2P_CHANNEL_COUNT];
u8 pa_type:4, patch_cck_gain:1, patch_cr157:1, patch_6m_band_edge:1,
- is_zd1211b:1;
+ new_phy_layout:1, is_zd1211b:1;
};
static inline struct zd_chip *zd_usb_to_chip(struct zd_usb *usb)
@@ -739,8 +748,12 @@
return zd_usb_rfwrite(&chip->usb, value, bits);
}
+int zd_rfwrite_cr_locked(struct zd_chip *chip, u32 value);
+
int zd_rfwritev_locked(struct zd_chip *chip,
const u32* values, unsigned int count, u8 bits);
+int zd_rfwritev_cr_locked(struct zd_chip *chip,
+ const u32* values, unsigned int count);
/* Locking functions for reading and writing registers.
* The different parameters are intentional.
diff --git a/drivers/net/wireless/zd1211rw/zd_def.h b/drivers/net/wireless/zd1211rw/zd_def.h
index 4659068..a13ec72 100644
--- a/drivers/net/wireless/zd1211rw/zd_def.h
+++ b/drivers/net/wireless/zd1211rw/zd_def.h
@@ -45,4 +45,10 @@
# define ZD_ASSERT(x) do { } while (0)
#endif
+#ifdef DEBUG
+# define ZD_MEMCLEAR(pointer, size) memset((pointer), 0xff, (size))
+#else
+# define ZD_MEMCLEAR(pointer, size) do { } while (0)
+#endif
+
#endif /* _ZD_DEF_H */
diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c
index d6f3e02..0eda534 100644
--- a/drivers/net/wireless/zd1211rw/zd_mac.c
+++ b/drivers/net/wireless/zd1211rw/zd_mac.c
@@ -127,11 +127,9 @@
void zd_mac_clear(struct zd_mac *mac)
{
- /* Aquire the lock. */
- spin_lock(&mac->lock);
- spin_unlock(&mac->lock);
zd_chip_clear(&mac->chip);
- memset(mac, 0, sizeof(*mac));
+ ZD_ASSERT(!spin_is_locked(&mac->lock));
+ ZD_MEMCLEAR(mac, sizeof(struct zd_mac));
}
static int reset_mode(struct zd_mac *mac)
diff --git a/drivers/net/wireless/zd1211rw/zd_mac.h b/drivers/net/wireless/zd1211rw/zd_mac.h
index 71e382c..082bcf8 100644
--- a/drivers/net/wireless/zd1211rw/zd_mac.h
+++ b/drivers/net/wireless/zd1211rw/zd_mac.h
@@ -121,9 +121,9 @@
};
struct zd_mac {
- struct net_device *netdev;
struct zd_chip chip;
spinlock_t lock;
+ struct net_device *netdev;
/* Unlocked reading possible */
struct iw_statistics iw_stats;
u8 qual_average;
diff --git a/drivers/net/wireless/zd1211rw/zd_netdev.c b/drivers/net/wireless/zd1211rw/zd_netdev.c
index 9df232c..440ef24 100644
--- a/drivers/net/wireless/zd1211rw/zd_netdev.c
+++ b/drivers/net/wireless/zd1211rw/zd_netdev.c
@@ -72,10 +72,18 @@
struct iw_request_info *info,
union iwreq_data *req, char *extra)
{
- /* FIXME: check whether 802.11a will also supported, add also
- * zd1211B, if we support it.
- */
- strlcpy(req->name, "802.11g zd1211", IFNAMSIZ);
+ /* FIXME: check whether 802.11a will also supported */
+ strlcpy(req->name, "IEEE 802.11b/g", IFNAMSIZ);
+ return 0;
+}
+
+static int iw_get_nick(struct net_device *netdev,
+ struct iw_request_info *info,
+ union iwreq_data *req, char *extra)
+{
+ strcpy(extra, "zd1211");
+ req->data.length = strlen(extra) + 1;
+ req->data.flags = 1;
return 0;
}
@@ -181,6 +189,7 @@
static const iw_handler zd_standard_iw_handlers[] = {
WX(SIOCGIWNAME) = iw_get_name,
+ WX(SIOCGIWNICKN) = iw_get_nick,
WX(SIOCSIWFREQ) = iw_set_freq,
WX(SIOCGIWFREQ) = iw_get_freq,
WX(SIOCSIWMODE) = iw_set_mode,
diff --git a/drivers/net/wireless/zd1211rw/zd_rf.c b/drivers/net/wireless/zd1211rw/zd_rf.c
index d3770d2..f50cff3 100644
--- a/drivers/net/wireless/zd1211rw/zd_rf.c
+++ b/drivers/net/wireless/zd1211rw/zd_rf.c
@@ -56,7 +56,7 @@
void zd_rf_clear(struct zd_rf *rf)
{
- memset(rf, 0, sizeof(*rf));
+ ZD_MEMCLEAR(rf, sizeof(*rf));
}
int zd_rf_init_hw(struct zd_rf *rf, u8 type)
@@ -76,6 +76,11 @@
if (r)
return r;
break;
+ case AL7230B_RF:
+ r = zd_rf_init_al7230b(rf);
+ if (r)
+ return r;
+ break;
default:
dev_err(zd_chip_dev(chip),
"RF %s %#x is not supported\n", zd_rf_name(type), type);
diff --git a/drivers/net/wireless/zd1211rw/zd_rf.h b/drivers/net/wireless/zd1211rw/zd_rf.h
index ea30f69..676b373 100644
--- a/drivers/net/wireless/zd1211rw/zd_rf.h
+++ b/drivers/net/wireless/zd1211rw/zd_rf.h
@@ -78,5 +78,6 @@
int zd_rf_init_rf2959(struct zd_rf *rf);
int zd_rf_init_al2230(struct zd_rf *rf);
+int zd_rf_init_al7230b(struct zd_rf *rf);
#endif /* _ZD_RF_H */
diff --git a/drivers/net/wireless/zd1211rw/zd_rf_al2230.c b/drivers/net/wireless/zd1211rw/zd_rf_al2230.c
index 0948b25..25323a1 100644
--- a/drivers/net/wireless/zd1211rw/zd_rf_al2230.c
+++ b/drivers/net/wireless/zd1211rw/zd_rf_al2230.c
@@ -21,7 +21,7 @@
#include "zd_usb.h"
#include "zd_chip.h"
-static const u32 al2230_table[][3] = {
+static const u32 zd1211_al2230_table[][3] = {
RF_CHANNEL( 1) = { 0x03f790, 0x033331, 0x00000d, },
RF_CHANNEL( 2) = { 0x03f790, 0x0b3331, 0x00000d, },
RF_CHANNEL( 3) = { 0x03e790, 0x033331, 0x00000d, },
@@ -38,6 +38,53 @@
RF_CHANNEL(14) = { 0x03e7c0, 0x066661, 0x00000d, },
};
+static const u32 zd1211b_al2230_table[][3] = {
+ RF_CHANNEL( 1) = { 0x09efc0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL( 2) = { 0x09efc0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL( 3) = { 0x09e7c0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL( 4) = { 0x09e7c0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL( 5) = { 0x05efc0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL( 6) = { 0x05efc0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL( 7) = { 0x05e7c0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL( 8) = { 0x05e7c0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL( 9) = { 0x0defc0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL(10) = { 0x0defc0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL(11) = { 0x0de7c0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL(12) = { 0x0de7c0, 0x8cccd0, 0xb00000, },
+ RF_CHANNEL(13) = { 0x03efc0, 0x8cccc0, 0xb00000, },
+ RF_CHANNEL(14) = { 0x03e7c0, 0x866660, 0xb00000, },
+};
+
+static const struct zd_ioreq16 zd1211b_ioreqs_shared_1[] = {
+ { CR240, 0x57 }, { CR9, 0xe0 },
+};
+
+static int zd1211b_al2230_finalize_rf(struct zd_chip *chip)
+{
+ int r;
+ static const struct zd_ioreq16 ioreqs[] = {
+ { CR80, 0x30 }, { CR81, 0x30 }, { CR79, 0x58 },
+ { CR12, 0xf0 }, { CR77, 0x1b }, { CR78, 0x58 },
+ { CR203, 0x06 },
+ { },
+
+ { CR240, 0x80 },
+ };
+
+ r = zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs));
+ if (r)
+ return r;
+
+ /* related to antenna selection? */
+ if (chip->new_phy_layout) {
+ r = zd_iowrite16_locked(chip, 0xe1, CR9);
+ if (r)
+ return r;
+ }
+
+ return zd_iowrite16_locked(chip, 0x06, CR203);
+}
+
static int zd1211_al2230_init_hw(struct zd_rf *rf)
{
int r;
@@ -139,7 +186,7 @@
{ CR47, 0x1e },
/* ZD1211B 05.06.10 */
- { CR48, 0x00 }, { CR49, 0x00 }, { CR51, 0x01 },
+ { CR48, 0x06 }, { CR49, 0xf9 }, { CR51, 0x01 },
{ CR52, 0x80 }, { CR53, 0x7e }, { CR65, 0x00 },
{ CR66, 0x00 }, { CR67, 0x00 }, { CR68, 0x00 },
{ CR69, 0x28 },
@@ -172,79 +219,78 @@
{ CR137, 0x50 }, /* 5614 */
{ CR138, 0xa8 },
{ CR144, 0xac }, /* 5621 */
- { CR150, 0x0d }, { CR252, 0x00 }, { CR253, 0x00 },
+ { CR150, 0x0d }, { CR252, 0x34 }, { CR253, 0x34 },
};
static const u32 rv1[] = {
- /* channel 1 */
- 0x03f790,
- 0x033331,
- 0x00000d,
+ 0x8cccd0,
+ 0x481dc0,
+ 0xcfff00,
+ 0x25a000,
- 0x0b3331,
- 0x03b812,
- 0x00fff3,
- 0x0005a4,
- 0x0f4dc5, /* fix freq shift 0x044dc5 */
- 0x0805b6,
- 0x0146c7,
- 0x000688,
- 0x0403b9, /* External control TX power (CR31) */
- 0x00dbba,
- 0x00099b,
- 0x0bdffc,
- 0x00000d,
- 0x00580f,
+ /* To improve AL2230 yield, improve phase noise, 4713 */
+ 0x25a000,
+ 0xa3b2f0,
+
+ 0x6da010, /* Reg6 update for MP versio */
+ 0xe36280, /* Modified by jxiao for Bor-Chin on 2004/08/02 */
+ 0x116000,
+ 0x9dc020, /* External control TX power (CR31) */
+ 0x5ddb00, /* RegA update for MP version */
+ 0xd99000, /* RegB update for MP version */
+ 0x3ffbd0, /* RegC update for MP version */
+ 0xb00000, /* RegD update for MP version */
+
+ /* improve phase noise and remove phase calibration,4713 */
+ 0xf01a00,
};
static const struct zd_ioreq16 ioreqs2[] = {
- { CR47, 0x1e }, { CR_RFCFG, 0x03 },
+ { CR251, 0x2f }, /* shdnb(PLL_ON)=0 */
+ { CR251, 0x7f }, /* shdnb(PLL_ON)=1 */
};
static const u32 rv2[] = {
- 0x00880f,
- 0x00080f,
+ /* To improve AL2230 yield, 4713 */
+ 0xf01b00,
+ 0xf01e00,
+ 0xf01a00,
};
static const struct zd_ioreq16 ioreqs3[] = {
- { CR_RFCFG, 0x00 }, { CR47, 0x1e }, { CR251, 0x7f },
+ /* related to 6M band edge patching, happens unconditionally */
+ { CR128, 0x14 }, { CR129, 0x12 }, { CR130, 0x10 },
};
- static const u32 rv3[] = {
- 0x00d80f,
- 0x00780f,
- 0x00580f,
- };
-
- static const struct zd_ioreq16 ioreqs4[] = {
- { CR138, 0x28 }, { CR203, 0x06 },
- };
-
+ r = zd_iowrite16a_locked(chip, zd1211b_ioreqs_shared_1,
+ ARRAY_SIZE(zd1211b_ioreqs_shared_1));
+ if (r)
+ return r;
r = zd_iowrite16a_locked(chip, ioreqs1, ARRAY_SIZE(ioreqs1));
if (r)
return r;
- r = zd_rfwritev_locked(chip, rv1, ARRAY_SIZE(rv1), RF_RV_BITS);
+ r = zd_rfwritev_cr_locked(chip, zd1211b_al2230_table[0], 3);
+ if (r)
+ return r;
+ r = zd_rfwritev_cr_locked(chip, rv1, ARRAY_SIZE(rv1));
if (r)
return r;
r = zd_iowrite16a_locked(chip, ioreqs2, ARRAY_SIZE(ioreqs2));
if (r)
return r;
- r = zd_rfwritev_locked(chip, rv2, ARRAY_SIZE(rv2), RF_RV_BITS);
+ r = zd_rfwritev_cr_locked(chip, rv2, ARRAY_SIZE(rv2));
if (r)
return r;
r = zd_iowrite16a_locked(chip, ioreqs3, ARRAY_SIZE(ioreqs3));
if (r)
return r;
- r = zd_rfwritev_locked(chip, rv3, ARRAY_SIZE(rv3), RF_RV_BITS);
- if (r)
- return r;
- return zd_iowrite16a_locked(chip, ioreqs4, ARRAY_SIZE(ioreqs4));
+ return zd1211b_al2230_finalize_rf(chip);
}
-static int al2230_set_channel(struct zd_rf *rf, u8 channel)
+static int zd1211_al2230_set_channel(struct zd_rf *rf, u8 channel)
{
int r;
- const u32 *rv = al2230_table[channel-1];
+ const u32 *rv = zd1211_al2230_table[channel-1];
struct zd_chip *chip = zd_rf_to_chip(rf);
static const struct zd_ioreq16 ioreqs[] = {
{ CR138, 0x28 },
@@ -257,6 +303,24 @@
return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs));
}
+static int zd1211b_al2230_set_channel(struct zd_rf *rf, u8 channel)
+{
+ int r;
+ const u32 *rv = zd1211b_al2230_table[channel-1];
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+
+ r = zd_iowrite16a_locked(chip, zd1211b_ioreqs_shared_1,
+ ARRAY_SIZE(zd1211b_ioreqs_shared_1));
+ if (r)
+ return r;
+
+ r = zd_rfwritev_cr_locked(chip, rv, 3);
+ if (r)
+ return r;
+
+ return zd1211b_al2230_finalize_rf(chip);
+}
+
static int zd1211_al2230_switch_radio_on(struct zd_rf *rf)
{
struct zd_chip *chip = zd_rf_to_chip(rf);
@@ -294,13 +358,14 @@
{
struct zd_chip *chip = zd_rf_to_chip(rf);
- rf->set_channel = al2230_set_channel;
rf->switch_radio_off = al2230_switch_radio_off;
if (chip->is_zd1211b) {
rf->init_hw = zd1211b_al2230_init_hw;
+ rf->set_channel = zd1211b_al2230_set_channel;
rf->switch_radio_on = zd1211b_al2230_switch_radio_on;
} else {
rf->init_hw = zd1211_al2230_init_hw;
+ rf->set_channel = zd1211_al2230_set_channel;
rf->switch_radio_on = zd1211_al2230_switch_radio_on;
}
rf->patch_6m_band_edge = 1;
diff --git a/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c b/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c
new file mode 100644
index 0000000..a289f95
--- /dev/null
+++ b/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c
@@ -0,0 +1,274 @@
+/* zd_rf_al7230b.c: Functions for the AL7230B RF controller
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/kernel.h>
+
+#include "zd_rf.h"
+#include "zd_usb.h"
+#include "zd_chip.h"
+
+static const u32 chan_rv[][2] = {
+ RF_CHANNEL( 1) = { 0x09ec00, 0x8cccc8 },
+ RF_CHANNEL( 2) = { 0x09ec00, 0x8cccd8 },
+ RF_CHANNEL( 3) = { 0x09ec00, 0x8cccc0 },
+ RF_CHANNEL( 4) = { 0x09ec00, 0x8cccd0 },
+ RF_CHANNEL( 5) = { 0x05ec00, 0x8cccc8 },
+ RF_CHANNEL( 6) = { 0x05ec00, 0x8cccd8 },
+ RF_CHANNEL( 7) = { 0x05ec00, 0x8cccc0 },
+ RF_CHANNEL( 8) = { 0x05ec00, 0x8cccd0 },
+ RF_CHANNEL( 9) = { 0x0dec00, 0x8cccc8 },
+ RF_CHANNEL(10) = { 0x0dec00, 0x8cccd8 },
+ RF_CHANNEL(11) = { 0x0dec00, 0x8cccc0 },
+ RF_CHANNEL(12) = { 0x0dec00, 0x8cccd0 },
+ RF_CHANNEL(13) = { 0x03ec00, 0x8cccc8 },
+ RF_CHANNEL(14) = { 0x03ec00, 0x866660 },
+};
+
+static const u32 std_rv[] = {
+ 0x4ff821,
+ 0xc5fbfc,
+ 0x21ebfe,
+ 0xafd401, /* freq shift 0xaad401 */
+ 0x6cf56a,
+ 0xe04073,
+ 0x193d76,
+ 0x9dd844,
+ 0x500007,
+ 0xd8c010,
+};
+
+static int al7230b_init_hw(struct zd_rf *rf)
+{
+ int i, r;
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+
+ /* All of these writes are identical to AL2230 unless otherwise
+ * specified */
+ static const struct zd_ioreq16 ioreqs_1[] = {
+ /* This one is 7230-specific, and happens before the rest */
+ { CR240, 0x57 },
+ { },
+
+ { CR15, 0x20 }, { CR23, 0x40 }, { CR24, 0x20 },
+ { CR26, 0x11 }, { CR28, 0x3e }, { CR29, 0x00 },
+ { CR44, 0x33 },
+ /* This value is different for 7230 (was: 0x2a) */
+ { CR106, 0x22 },
+ { CR107, 0x1a }, { CR109, 0x09 }, { CR110, 0x27 },
+ { CR111, 0x2b }, { CR112, 0x2b }, { CR119, 0x0a },
+ /* This happened further down in AL2230,
+ * and the value changed (was: 0xe0) */
+ { CR122, 0xfc },
+ { CR10, 0x89 },
+ /* for newest (3rd cut) AL2300 */
+ { CR17, 0x28 },
+ { CR26, 0x93 }, { CR34, 0x30 },
+ /* for newest (3rd cut) AL2300 */
+ { CR35, 0x3e },
+ { CR41, 0x24 }, { CR44, 0x32 },
+ /* for newest (3rd cut) AL2300 */
+ { CR46, 0x96 },
+ { CR47, 0x1e }, { CR79, 0x58 }, { CR80, 0x30 },
+ { CR81, 0x30 }, { CR87, 0x0a }, { CR89, 0x04 },
+ { CR92, 0x0a }, { CR99, 0x28 },
+ /* This value is different for 7230 (was: 0x00) */
+ { CR100, 0x02 },
+ { CR101, 0x13 }, { CR102, 0x27 },
+ /* This value is different for 7230 (was: 0x24) */
+ { CR106, 0x22 },
+ /* This value is different for 7230 (was: 0x2a) */
+ { CR107, 0x3f },
+ { CR109, 0x09 },
+ /* This value is different for 7230 (was: 0x13) */
+ { CR110, 0x1f },
+ { CR111, 0x1f }, { CR112, 0x1f }, { CR113, 0x27 },
+ { CR114, 0x27 },
+ /* for newest (3rd cut) AL2300 */
+ { CR115, 0x24 },
+ /* This value is different for 7230 (was: 0x24) */
+ { CR116, 0x3f },
+ /* This value is different for 7230 (was: 0xf4) */
+ { CR117, 0xfa },
+ { CR118, 0xfc }, { CR119, 0x10 }, { CR120, 0x4f },
+ { CR121, 0x77 }, { CR137, 0x88 },
+ /* This one is 7230-specific */
+ { CR138, 0xa8 },
+ /* This value is different for 7230 (was: 0xff) */
+ { CR252, 0x34 },
+ /* This value is different for 7230 (was: 0xff) */
+ { CR253, 0x34 },
+
+ /* PLL_OFF */
+ { CR251, 0x2f },
+ };
+
+ static const struct zd_ioreq16 ioreqs_2[] = {
+ /* PLL_ON */
+ { CR251, 0x3f },
+ { CR128, 0x14 }, { CR129, 0x12 }, { CR130, 0x10 },
+ { CR38, 0x38 }, { CR136, 0xdf },
+ };
+
+ r = zd_iowrite16a_locked(chip, ioreqs_1, ARRAY_SIZE(ioreqs_1));
+ if (r)
+ return r;
+
+ r = zd_rfwrite_cr_locked(chip, 0x09ec04);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0x8cccc8);
+ if (r)
+ return r;
+
+ for (i = 0; i < ARRAY_SIZE(std_rv); i++) {
+ r = zd_rfwrite_cr_locked(chip, std_rv[i]);
+ if (r)
+ return r;
+ }
+
+ r = zd_rfwrite_cr_locked(chip, 0x3c9000);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0xbfffff);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0x700000);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0xf15d58);
+ if (r)
+ return r;
+
+ r = zd_iowrite16a_locked(chip, ioreqs_2, ARRAY_SIZE(ioreqs_2));
+ if (r)
+ return r;
+
+ r = zd_rfwrite_cr_locked(chip, 0xf15d59);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0xf15d5c);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0xf15d58);
+ if (r)
+ return r;
+
+ r = zd_iowrite16_locked(chip, 0x06, CR203);
+ if (r)
+ return r;
+ r = zd_iowrite16_locked(chip, 0x80, CR240);
+ if (r)
+ return r;
+
+ return 0;
+}
+
+static int al7230b_set_channel(struct zd_rf *rf, u8 channel)
+{
+ int i, r;
+ const u32 *rv = chan_rv[channel-1];
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+
+ struct zd_ioreq16 ioreqs_1[] = {
+ { CR128, 0x14 }, { CR129, 0x12 }, { CR130, 0x10 },
+ { CR38, 0x38 }, { CR136, 0xdf },
+ };
+
+ struct zd_ioreq16 ioreqs_2[] = {
+ /* PLL_ON */
+ { CR251, 0x3f },
+ { CR203, 0x06 }, { CR240, 0x08 },
+ };
+
+ r = zd_iowrite16_locked(chip, 0x57, CR240);
+ if (r)
+ return r;
+
+ /* PLL_OFF */
+ r = zd_iowrite16_locked(chip, 0x2f, CR251);
+ if (r)
+ return r;
+
+ for (i = 0; i < ARRAY_SIZE(std_rv); i++) {
+ r = zd_rfwrite_cr_locked(chip, std_rv[i]);
+ if (r)
+ return r;
+ }
+
+ r = zd_rfwrite_cr_locked(chip, 0x3c9000);
+ if (r)
+ return r;
+ r = zd_rfwrite_cr_locked(chip, 0xf15d58);
+ if (r)
+ return r;
+
+ r = zd_iowrite16a_locked(chip, ioreqs_1, ARRAY_SIZE(ioreqs_1));
+ if (r)
+ return r;
+
+ for (i = 0; i < 2; i++) {
+ r = zd_rfwrite_cr_locked(chip, rv[i]);
+ if (r)
+ return r;
+ }
+
+ r = zd_rfwrite_cr_locked(chip, 0x3c9000);
+ if (r)
+ return r;
+
+ return zd_iowrite16a_locked(chip, ioreqs_2, ARRAY_SIZE(ioreqs_2));
+}
+
+static int al7230b_switch_radio_on(struct zd_rf *rf)
+{
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+ static const struct zd_ioreq16 ioreqs[] = {
+ { CR11, 0x00 },
+ { CR251, 0x3f },
+ };
+
+ return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs));
+}
+
+static int al7230b_switch_radio_off(struct zd_rf *rf)
+{
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+ static const struct zd_ioreq16 ioreqs[] = {
+ { CR11, 0x04 },
+ { CR251, 0x2f },
+ };
+
+ return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs));
+}
+
+int zd_rf_init_al7230b(struct zd_rf *rf)
+{
+ struct zd_chip *chip = zd_rf_to_chip(rf);
+
+ if (chip->is_zd1211b) {
+ dev_err(zd_chip_dev(chip), "AL7230B is currently not "
+ "supported for ZD1211B devices\n");
+ return -ENODEV;
+ }
+
+ rf->init_hw = al7230b_init_hw;
+ rf->set_channel = al7230b_set_channel;
+ rf->switch_radio_on = al7230b_switch_radio_on;
+ rf->switch_radio_off = al7230b_switch_radio_off;
+ rf->patch_6m_band_edge = 1;
+ return 0;
+}
diff --git a/drivers/net/wireless/zd1211rw/zd_usb.c b/drivers/net/wireless/zd1211rw/zd_usb.c
index 6320984..47489fe 100644
--- a/drivers/net/wireless/zd1211rw/zd_usb.c
+++ b/drivers/net/wireless/zd1211rw/zd_usb.c
@@ -16,6 +16,7 @@
*/
#include <asm/unaligned.h>
+#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/firmware.h>
@@ -39,9 +40,17 @@
{ USB_DEVICE(0x6891, 0xa727), .driver_info = DEVICE_ZD1211 },
{ USB_DEVICE(0x0df6, 0x9071), .driver_info = DEVICE_ZD1211 },
{ USB_DEVICE(0x157e, 0x300b), .driver_info = DEVICE_ZD1211 },
+ { USB_DEVICE(0x079b, 0x004a), .driver_info = DEVICE_ZD1211 },
+ { USB_DEVICE(0x1740, 0x2000), .driver_info = DEVICE_ZD1211 },
+ { USB_DEVICE(0x157e, 0x3204), .driver_info = DEVICE_ZD1211 },
+ { USB_DEVICE(0x0586, 0x3402), .driver_info = DEVICE_ZD1211 },
/* ZD1211B */
{ USB_DEVICE(0x0ace, 0x1215), .driver_info = DEVICE_ZD1211B },
{ USB_DEVICE(0x157e, 0x300d), .driver_info = DEVICE_ZD1211B },
+ { USB_DEVICE(0x079b, 0x0062), .driver_info = DEVICE_ZD1211B },
+ { USB_DEVICE(0x1582, 0x6003), .driver_info = DEVICE_ZD1211B },
+ /* "Driverless" devices that need ejecting */
+ { USB_DEVICE(0x0ace, 0x2011), .driver_info = DEVICE_INSTALLER },
{}
};
@@ -263,6 +272,39 @@
return buffer;
}
+static int handle_version_mismatch(struct usb_device *udev, u8 device_type,
+ const struct firmware *ub_fw)
+{
+ const struct firmware *ur_fw = NULL;
+ int offset;
+ int r = 0;
+ char fw_name[128];
+
+ r = request_fw_file(&ur_fw,
+ get_fw_name(fw_name, sizeof(fw_name), device_type, "ur"),
+ &udev->dev);
+ if (r)
+ goto error;
+
+ r = upload_code(udev, ur_fw->data, ur_fw->size, FW_START_OFFSET,
+ REBOOT);
+ if (r)
+ goto error;
+
+ offset = ((EEPROM_REGS_OFFSET + EEPROM_REGS_SIZE) * sizeof(u16));
+ r = upload_code(udev, ub_fw->data + offset, ub_fw->size - offset,
+ E2P_BASE_OFFSET + EEPROM_REGS_SIZE, REBOOT);
+
+ /* At this point, the vendor driver downloads the whole firmware
+ * image, hacks around with version IDs, and uploads it again,
+ * completely overwriting the boot code. We do not do this here as
+ * it is not required on any tested devices, and it is suspected to
+ * cause problems. */
+error:
+ release_firmware(ur_fw);
+ return r;
+}
+
static int upload_firmware(struct usb_device *udev, u8 device_type)
{
int r;
@@ -282,15 +324,17 @@
fw_bcdDevice = get_word(ub_fw->data, EEPROM_REGS_OFFSET);
- /* FIXME: do we have any reason to perform the kludge that the vendor
- * driver does when there is a version mismatch? (their driver uploads
- * different firmwares and stuff)
- */
if (fw_bcdDevice != bcdDevice) {
dev_info(&udev->dev,
- "firmware device id %#06x and actual device id "
- "%#06x differ, continuing anyway\n",
- fw_bcdDevice, bcdDevice);
+ "firmware version %#06x and device bootcode version "
+ "%#06x differ\n", fw_bcdDevice, bcdDevice);
+ if (bcdDevice <= 0x4313)
+ dev_warn(&udev->dev, "device has old bootcode, please "
+ "report success or failure\n");
+
+ r = handle_version_mismatch(udev, device_type, ub_fw);
+ if (r)
+ goto error;
} else {
dev_dbg_f(&udev->dev,
"firmware device id %#06x is equal to the "
@@ -620,7 +664,7 @@
usb_submit_urb(urb, GFP_ATOMIC);
}
-struct urb *alloc_urb(struct zd_usb *usb)
+static struct urb *alloc_urb(struct zd_usb *usb)
{
struct usb_device *udev = zd_usb_to_usbdev(usb);
struct urb *urb;
@@ -644,7 +688,7 @@
return urb;
}
-void free_urb(struct urb *urb)
+static void free_urb(struct urb *urb)
{
if (!urb)
return;
@@ -864,7 +908,7 @@
{
usb_set_intfdata(usb->intf, NULL);
usb_put_intf(usb->intf);
- memset(usb, 0, sizeof(*usb));
+ ZD_MEMCLEAR(usb, sizeof(*usb));
/* FIXME: usb_interrupt, usb_tx, usb_rx? */
}
@@ -910,6 +954,55 @@
#define print_id(udev) do { } while (0)
#endif
+static int eject_installer(struct usb_interface *intf)
+{
+ struct usb_device *udev = interface_to_usbdev(intf);
+ struct usb_host_interface *iface_desc = &intf->altsetting[0];
+ struct usb_endpoint_descriptor *endpoint;
+ unsigned char *cmd;
+ u8 bulk_out_ep;
+ int r;
+
+ /* Find bulk out endpoint */
+ endpoint = &iface_desc->endpoint[1].desc;
+ if ((endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT &&
+ (endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+ USB_ENDPOINT_XFER_BULK) {
+ bulk_out_ep = endpoint->bEndpointAddress;
+ } else {
+ dev_err(&udev->dev,
+ "zd1211rw: Could not find bulk out endpoint\n");
+ return -ENODEV;
+ }
+
+ cmd = kzalloc(31, GFP_KERNEL);
+ if (cmd == NULL)
+ return -ENODEV;
+
+ /* USB bulk command block */
+ cmd[0] = 0x55; /* bulk command signature */
+ cmd[1] = 0x53; /* bulk command signature */
+ cmd[2] = 0x42; /* bulk command signature */
+ cmd[3] = 0x43; /* bulk command signature */
+ cmd[14] = 6; /* command length */
+
+ cmd[15] = 0x1b; /* SCSI command: START STOP UNIT */
+ cmd[19] = 0x2; /* eject disc */
+
+ dev_info(&udev->dev, "Ejecting virtual installer media...\n");
+ r = usb_bulk_msg(udev, usb_sndbulkpipe(udev, bulk_out_ep),
+ cmd, 31, NULL, 2000);
+ kfree(cmd);
+ if (r)
+ return r;
+
+ /* At this point, the device disconnects and reconnects with the real
+ * ID numbers. */
+
+ usb_set_intfdata(intf, NULL);
+ return 0;
+}
+
static int probe(struct usb_interface *intf, const struct usb_device_id *id)
{
int r;
@@ -918,6 +1011,9 @@
print_id(udev);
+ if (id->driver_info & DEVICE_INSTALLER)
+ return eject_installer(intf);
+
switch (udev->speed) {
case USB_SPEED_LOW:
case USB_SPEED_FULL:
@@ -983,6 +1079,11 @@
struct zd_mac *mac = zd_netdev_mac(netdev);
struct zd_usb *usb = &mac->chip.usb;
+ /* Either something really bad happened, or we're just dealing with
+ * a DEVICE_INSTALLER. */
+ if (netdev == NULL)
+ return;
+
dev_dbg_f(zd_usb_dev(usb), "\n");
zd_netdev_disconnect(netdev);
@@ -998,7 +1099,6 @@
*/
usb_reset_device(interface_to_usbdev(intf));
- /* If somebody still waits on this lock now, this is an error. */
zd_netdev_free(netdev);
dev_dbg(&intf->dev, "disconnected\n");
}
diff --git a/drivers/net/wireless/zd1211rw/zd_usb.h b/drivers/net/wireless/zd1211rw/zd_usb.h
index d642028..92746f7 100644
--- a/drivers/net/wireless/zd1211rw/zd_usb.h
+++ b/drivers/net/wireless/zd1211rw/zd_usb.h
@@ -30,6 +30,7 @@
enum devicetype {
DEVICE_ZD1211 = 0,
DEVICE_ZD1211B = 1,
+ DEVICE_INSTALLER = 2,
};
enum endpoints {
diff --git a/drivers/net/yellowfin.c b/drivers/net/yellowfin.c
index 8459a18..b6b2474 100644
--- a/drivers/net/yellowfin.c
+++ b/drivers/net/yellowfin.c
@@ -1434,7 +1434,7 @@
#ifdef MODULE
printk(version);
#endif
- return pci_module_init (&yellowfin_driver);
+ return pci_register_driver(&yellowfin_driver);
}
diff --git a/include/net/ieee80211.h b/include/net/ieee80211.h
index ecc4286..b174ebb 100644
--- a/include/net/ieee80211.h
+++ b/include/net/ieee80211.h
@@ -240,6 +240,11 @@
#define WLAN_CAPABILITY_SHORT_SLOT_TIME (1<<10)
#define WLAN_CAPABILITY_DSSS_OFDM (1<<13)
+/* 802.11g ERP information element */
+#define WLAN_ERP_NON_ERP_PRESENT (1<<0)
+#define WLAN_ERP_USE_PROTECTION (1<<1)
+#define WLAN_ERP_BARKER_PREAMBLE (1<<2)
+
/* Status codes */
enum ieee80211_statuscode {
WLAN_STATUS_SUCCESS = 0,
@@ -747,6 +752,8 @@
#define NETWORK_HAS_IBSS_DFS (1<<8)
#define NETWORK_HAS_TPC_REPORT (1<<9)
+#define NETWORK_HAS_ERP_VALUE (1<<10)
+
#define QOS_QUEUE_NUM 4
#define QOS_OUI_LEN 3
#define QOS_OUI_TYPE 2
@@ -1252,6 +1259,8 @@
int total_len, int encrypt_mpdu);
/* ieee80211_rx.c */
+extern void ieee80211_rx_any(struct ieee80211_device *ieee,
+ struct sk_buff *skb, struct ieee80211_rx_stats *stats);
extern int ieee80211_rx(struct ieee80211_device *ieee, struct sk_buff *skb,
struct ieee80211_rx_stats *rx_stats);
/* make sure to set stats->len */
diff --git a/include/net/ieee80211softmac.h b/include/net/ieee80211softmac.h
index 00ad810..425b3a5 100644
--- a/include/net/ieee80211softmac.h
+++ b/include/net/ieee80211softmac.h
@@ -86,9 +86,6 @@
/* BSSID we're trying to associate to */
char bssid[ETH_ALEN];
-
- /* Rates supported by the network */
- struct ieee80211softmac_ratesinfo supported_rates;
/* some flags.
* static_essid is valid if the essid is constant,
@@ -103,6 +100,7 @@
* bssfixed is used for SIOCSIWAP.
*/
u8 static_essid:1,
+ short_preamble_available:1,
associating:1,
assoc_wait:1,
bssvalid:1,
@@ -115,6 +113,19 @@
struct work_struct timeout;
};
+struct ieee80211softmac_bss_info {
+ /* Rates supported by the network */
+ struct ieee80211softmac_ratesinfo supported_rates;
+
+ /* This indicates whether frames can currently be transmitted with
+ * short preamble (only use this variable during TX at CCK rates) */
+ u8 short_preamble:1;
+
+ /* This indicates whether protection (e.g. self-CTS) should be used
+ * when transmitting with OFDM modulation */
+ u8 use_protection:1;
+};
+
enum {
IEEE80211SOFTMAC_AUTH_OPEN_REQUEST = 1,
IEEE80211SOFTMAC_AUTH_OPEN_RESPONSE = 2,
@@ -157,6 +168,10 @@
#define IEEE80211SOFTMAC_TXRATECHG_MCAST (1 << 2) /* mcast_rate */
#define IEEE80211SOFTMAC_TXRATECHG_MGT_MCAST (1 << 3) /* mgt_mcast_rate */
+#define IEEE80211SOFTMAC_BSSINFOCHG_RATES (1 << 0) /* supported_rates */
+#define IEEE80211SOFTMAC_BSSINFOCHG_SHORT_PREAMBLE (1 << 1) /* short_preamble */
+#define IEEE80211SOFTMAC_BSSINFOCHG_PROTECTION (1 << 2) /* use_protection */
+
struct ieee80211softmac_device {
/* 802.11 structure for data stuff */
struct ieee80211_device *ieee;
@@ -200,10 +215,16 @@
* The driver just needs to read them.
*/
struct ieee80211softmac_txrates txrates;
- /* If the driver needs to do stuff on TX rate changes, assign this callback. */
+
+ /* If the driver needs to do stuff on TX rate changes, assign this
+ * callback. See IEEE80211SOFTMAC_TXRATECHG for change flags. */
void (*txrates_change)(struct net_device *dev,
- u32 changes, /* see IEEE80211SOFTMAC_TXRATECHG flags */
- const struct ieee80211softmac_txrates *rates_before_change);
+ u32 changes);
+
+ /* If the driver needs to do stuff when BSS properties change, assign
+ * this callback. see IEEE80211SOFTMAC_BSSINFOCHG for change flags. */
+ void (*bssinfo_change)(struct net_device *dev,
+ u32 changes);
/* private stuff follows */
/* this lock protects this structure */
@@ -216,6 +237,7 @@
struct ieee80211softmac_scaninfo *scaninfo;
struct ieee80211softmac_assoc_info associnfo;
+ struct ieee80211softmac_bss_info bssinfo;
struct list_head auth_queue;
struct list_head events;
@@ -257,6 +279,14 @@
* Note that the rates need to be sorted. */
extern void ieee80211softmac_set_rates(struct net_device *dev, u8 count, u8 *rates);
+/* Finds the highest rate which is:
+ * 1. Present in ri (optionally a basic rate)
+ * 2. Supported by the device
+ * 3. Less than or equal to the user-defined rate
+ */
+extern u8 ieee80211softmac_highest_supported_rate(struct ieee80211softmac_device *mac,
+ struct ieee80211softmac_ratesinfo *ri, int basic_only);
+
/* Helper function which advises you the rate at which a frame should be
* transmitted at. */
static inline u8 ieee80211softmac_suggest_txrate(struct ieee80211softmac_device *mac,
@@ -279,6 +309,24 @@
return txrates->mcast_rate;
}
+/* Helper function which advises you when it is safe to transmit with short
+ * preamble.
+ * You should only call this function when transmitting at CCK rates. */
+static inline int ieee80211softmac_short_preamble_ok(struct ieee80211softmac_device *mac,
+ int is_multicast,
+ int is_mgt)
+{
+ return (is_multicast && is_mgt) ? 0 : mac->bssinfo.short_preamble;
+}
+
+/* Helper function which advises you whether protection (e.g. self-CTS) is
+ * needed. 1 = protection needed, 0 = no protection needed
+ * Only use this function when transmitting with OFDM modulation. */
+static inline int ieee80211softmac_protection_needed(struct ieee80211softmac_device *mac)
+{
+ return mac->bssinfo.use_protection;
+}
+
/* Start the SoftMAC. Call this after you initialized the device
* and it is ready to run.
*/
diff --git a/net/ieee80211/ieee80211_rx.c b/net/ieee80211/ieee80211_rx.c
index 72d4d4e..d60358d 100644
--- a/net/ieee80211/ieee80211_rx.c
+++ b/net/ieee80211/ieee80211_rx.c
@@ -779,33 +779,44 @@
return 0;
}
-/* Filter out unrelated packets, call ieee80211_rx[_mgt] */
-int ieee80211_rx_any(struct ieee80211_device *ieee,
+/* Filter out unrelated packets, call ieee80211_rx[_mgt]
+ * This function takes over the skb, it should not be used again after calling
+ * this function. */
+void ieee80211_rx_any(struct ieee80211_device *ieee,
struct sk_buff *skb, struct ieee80211_rx_stats *stats)
{
struct ieee80211_hdr_4addr *hdr;
int is_packet_for_us;
u16 fc;
- if (ieee->iw_mode == IW_MODE_MONITOR)
- return ieee80211_rx(ieee, skb, stats) ? 0 : -EINVAL;
+ if (ieee->iw_mode == IW_MODE_MONITOR) {
+ if (!ieee80211_rx(ieee, skb, stats))
+ dev_kfree_skb_irq(skb);
+ return;
+ }
+
+ if (skb->len < sizeof(struct ieee80211_hdr))
+ goto drop_free;
hdr = (struct ieee80211_hdr_4addr *)skb->data;
fc = le16_to_cpu(hdr->frame_ctl);
if ((fc & IEEE80211_FCTL_VERS) != 0)
- return -EINVAL;
+ goto drop_free;
switch (fc & IEEE80211_FCTL_FTYPE) {
case IEEE80211_FTYPE_MGMT:
+ if (skb->len < sizeof(struct ieee80211_hdr_3addr))
+ goto drop_free;
ieee80211_rx_mgt(ieee, hdr, stats);
- return 0;
+ dev_kfree_skb_irq(skb);
+ return;
case IEEE80211_FTYPE_DATA:
break;
case IEEE80211_FTYPE_CTL:
- return 0;
+ return;
default:
- return -EINVAL;
+ return;
}
is_packet_for_us = 0;
@@ -849,8 +860,14 @@
}
if (is_packet_for_us)
- return (ieee80211_rx(ieee, skb, stats) ? 0 : -EINVAL);
- return 0;
+ if (!ieee80211_rx(ieee, skb, stats))
+ dev_kfree_skb_irq(skb);
+ return;
+
+drop_free:
+ dev_kfree_skb_irq(skb);
+ ieee->stats.rx_dropped++;
+ return;
}
#define MGMT_FRAME_FIXED_PART_LENGTH 0x24
@@ -1166,6 +1183,7 @@
case MFIE_TYPE_ERP_INFO:
network->erp_value = info_element->data[0];
+ network->flags |= NETWORK_HAS_ERP_VALUE;
IEEE80211_DEBUG_MGMT("MFIE_TYPE_ERP_SET: %d\n",
network->erp_value);
break;
@@ -1729,5 +1747,6 @@
}
}
+EXPORT_SYMBOL_GPL(ieee80211_rx_any);
EXPORT_SYMBOL(ieee80211_rx_mgt);
EXPORT_SYMBOL(ieee80211_rx);
diff --git a/net/ieee80211/softmac/ieee80211softmac_assoc.c b/net/ieee80211/softmac/ieee80211softmac_assoc.c
index 44215ce..589f6d2 100644
--- a/net/ieee80211/softmac/ieee80211softmac_assoc.c
+++ b/net/ieee80211/softmac/ieee80211softmac_assoc.c
@@ -96,7 +96,7 @@
mac->associated = 0;
mac->associnfo.bssvalid = 0;
mac->associnfo.associating = 0;
- ieee80211softmac_init_txrates(mac);
+ ieee80211softmac_init_bss(mac);
ieee80211softmac_call_events_locked(mac, IEEE80211SOFTMAC_EVENT_DISASSOCIATED, NULL);
spin_unlock_irqrestore(&mac->lock, flags);
}
@@ -334,11 +334,19 @@
struct ieee80211_assoc_response * resp,
struct ieee80211softmac_network *net)
{
+ u16 cap = le16_to_cpu(resp->capability);
+ u8 erp_value = net->erp_value;
+
mac->associnfo.associating = 0;
- mac->associnfo.supported_rates = net->supported_rates;
+ mac->bssinfo.supported_rates = net->supported_rates;
ieee80211softmac_recalc_txrates(mac);
mac->associated = 1;
+
+ mac->associnfo.short_preamble_available =
+ (cap & WLAN_CAPABILITY_SHORT_PREAMBLE) != 0;
+ ieee80211softmac_process_erp(mac, erp_value);
+
if (mac->set_bssid_filter)
mac->set_bssid_filter(mac->dev, net->bssid);
memcpy(mac->ieee->bssid, net->bssid, ETH_ALEN);
@@ -351,9 +359,9 @@
int
ieee80211softmac_handle_assoc_response(struct net_device * dev,
struct ieee80211_assoc_response * resp,
- struct ieee80211_network * _ieee80211_network_do_not_use)
+ struct ieee80211_network * _ieee80211_network)
{
- /* NOTE: the network parameter has to be ignored by
+ /* NOTE: the network parameter has to be mostly ignored by
* this code because it is the ieee80211's pointer
* to the struct, not ours (we made a copy)
*/
@@ -385,6 +393,11 @@
/* now that we know it was for us, we can cancel the timeout */
cancel_delayed_work(&mac->associnfo.timeout);
+ /* if the association response included an ERP IE, update our saved
+ * copy */
+ if (_ieee80211_network->flags & NETWORK_HAS_ERP_VALUE)
+ network->erp_value = _ieee80211_network->erp_value;
+
switch (status) {
case 0:
dprintk(KERN_INFO PFX "associated!\n");
diff --git a/net/ieee80211/softmac/ieee80211softmac_io.c b/net/ieee80211/softmac/ieee80211softmac_io.c
index 6ae5a1d..82bfddb 100644
--- a/net/ieee80211/softmac/ieee80211softmac_io.c
+++ b/net/ieee80211/softmac/ieee80211softmac_io.c
@@ -467,3 +467,17 @@
kfree(pkt);
return 0;
}
+
+/* Beacon handling */
+int ieee80211softmac_handle_beacon(struct net_device *dev,
+ struct ieee80211_beacon *beacon,
+ struct ieee80211_network *network)
+{
+ struct ieee80211softmac_device *mac = ieee80211_priv(dev);
+
+ if (mac->associated && memcmp(network->bssid, mac->associnfo.bssid, ETH_ALEN) == 0)
+ ieee80211softmac_process_erp(mac, network->erp_value);
+
+ return 0;
+}
+
diff --git a/net/ieee80211/softmac/ieee80211softmac_module.c b/net/ieee80211/softmac/ieee80211softmac_module.c
index 4b2e57d..addea1c 100644
--- a/net/ieee80211/softmac/ieee80211softmac_module.c
+++ b/net/ieee80211/softmac/ieee80211softmac_module.c
@@ -44,6 +44,7 @@
softmac->ieee->handle_assoc_response = ieee80211softmac_handle_assoc_response;
softmac->ieee->handle_reassoc_request = ieee80211softmac_handle_reassoc_req;
softmac->ieee->handle_disassoc = ieee80211softmac_handle_disassoc;
+ softmac->ieee->handle_beacon = ieee80211softmac_handle_beacon;
softmac->scaninfo = NULL;
softmac->associnfo.scan_retry = IEEE80211SOFTMAC_ASSOC_SCAN_RETRY_LIMIT;
@@ -178,21 +179,14 @@
return 0;
}
-/* Finds the highest rate which is:
- * 1. Present in ri (optionally a basic rate)
- * 2. Supported by the device
- * 3. Less than or equal to the user-defined rate
- */
-static u8 highest_supported_rate(struct ieee80211softmac_device *mac,
+u8 ieee80211softmac_highest_supported_rate(struct ieee80211softmac_device *mac,
struct ieee80211softmac_ratesinfo *ri, int basic_only)
{
u8 user_rate = mac->txrates.user_rate;
int i;
- if (ri->count == 0) {
- dprintk(KERN_ERR PFX "empty ratesinfo?\n");
+ if (ri->count == 0)
return IEEE80211_CCK_RATE_1MB;
- }
for (i = ri->count - 1; i >= 0; i--) {
u8 rate = ri->rates[i];
@@ -208,36 +202,61 @@
/* If we haven't found a suitable rate by now, just trust the user */
return user_rate;
}
+EXPORT_SYMBOL_GPL(ieee80211softmac_highest_supported_rate);
+
+void ieee80211softmac_process_erp(struct ieee80211softmac_device *mac,
+ u8 erp_value)
+{
+ int use_protection;
+ int short_preamble;
+ u32 changes = 0;
+
+ /* Barker preamble mode */
+ short_preamble = ((erp_value & WLAN_ERP_BARKER_PREAMBLE) == 0
+ && mac->associnfo.short_preamble_available) ? 1 : 0;
+
+ /* Protection needed? */
+ use_protection = (erp_value & WLAN_ERP_USE_PROTECTION) != 0;
+
+ if (mac->bssinfo.short_preamble != short_preamble) {
+ changes |= IEEE80211SOFTMAC_BSSINFOCHG_SHORT_PREAMBLE;
+ mac->bssinfo.short_preamble = short_preamble;
+ }
+
+ if (mac->bssinfo.use_protection != use_protection) {
+ changes |= IEEE80211SOFTMAC_BSSINFOCHG_PROTECTION;
+ mac->bssinfo.use_protection = use_protection;
+ }
+
+ if (mac->bssinfo_change && changes)
+ mac->bssinfo_change(mac->dev, changes);
+}
void ieee80211softmac_recalc_txrates(struct ieee80211softmac_device *mac)
{
struct ieee80211softmac_txrates *txrates = &mac->txrates;
- struct ieee80211softmac_txrates oldrates;
u32 change = 0;
- if (mac->txrates_change)
- oldrates = mac->txrates;
-
change |= IEEE80211SOFTMAC_TXRATECHG_DEFAULT;
- txrates->default_rate = highest_supported_rate(mac, &mac->associnfo.supported_rates, 0);
+ txrates->default_rate = ieee80211softmac_highest_supported_rate(mac, &mac->bssinfo.supported_rates, 0);
change |= IEEE80211SOFTMAC_TXRATECHG_DEFAULT_FBACK;
txrates->default_fallback = lower_rate(mac, txrates->default_rate);
change |= IEEE80211SOFTMAC_TXRATECHG_MCAST;
- txrates->mcast_rate = highest_supported_rate(mac, &mac->associnfo.supported_rates, 1);
+ txrates->mcast_rate = ieee80211softmac_highest_supported_rate(mac, &mac->bssinfo.supported_rates, 1);
if (mac->txrates_change)
- mac->txrates_change(mac->dev, change, &oldrates);
+ mac->txrates_change(mac->dev, change);
}
-void ieee80211softmac_init_txrates(struct ieee80211softmac_device *mac)
+void ieee80211softmac_init_bss(struct ieee80211softmac_device *mac)
{
struct ieee80211_device *ieee = mac->ieee;
u32 change = 0;
struct ieee80211softmac_txrates *txrates = &mac->txrates;
- struct ieee80211softmac_txrates oldrates;
+ struct ieee80211softmac_bss_info *bssinfo = &mac->bssinfo;
/* TODO: We need some kind of state machine to lower the default rates
* if we loose too many packets.
@@ -245,8 +264,6 @@
/* Change the default txrate to the highest possible value.
* The txrate machine will lower it, if it is too high.
*/
- if (mac->txrates_change)
- oldrates = mac->txrates;
/* FIXME: We don't correctly handle backing down to lower
rates, so 801.11g devices start off at 11M for now. People
can manually change it if they really need to, but 11M is
@@ -272,7 +289,23 @@
change |= IEEE80211SOFTMAC_TXRATECHG_MGT_MCAST;
if (mac->txrates_change)
- mac->txrates_change(mac->dev, change, &oldrates);
+ mac->txrates_change(mac->dev, change);
+
+ change = 0;
+
+ bssinfo->supported_rates.count = 0;
+ memset(bssinfo->supported_rates.rates, 0,
+ sizeof(bssinfo->supported_rates.rates));
+ change |= IEEE80211SOFTMAC_BSSINFOCHG_RATES;
+
+ bssinfo->short_preamble = 0;
+ change |= IEEE80211SOFTMAC_BSSINFOCHG_SHORT_PREAMBLE;
+
+ bssinfo->use_protection = 0;
+ change |= IEEE80211SOFTMAC_BSSINFOCHG_PROTECTION;
+
+ if (mac->bssinfo_change)
+ mac->bssinfo_change(mac->dev, change);
mac->running = 1;
}
@@ -282,7 +315,7 @@
struct ieee80211softmac_device *mac = ieee80211_priv(dev);
ieee80211softmac_start_check_rates(mac);
- ieee80211softmac_init_txrates(mac);
+ ieee80211softmac_init_bss(mac);
}
EXPORT_SYMBOL_GPL(ieee80211softmac_start);
@@ -335,7 +368,6 @@
static void ieee80211softmac_add_txrates_badness(struct ieee80211softmac_device *mac,
int amount)
{
- struct ieee80211softmac_txrates oldrates;
u8 default_rate = mac->txrates.default_rate;
u8 default_fallback = mac->txrates.default_fallback;
u32 changes = 0;
@@ -348,8 +380,6 @@
mac->txrate_badness += amount;
if (mac->txrate_badness <= -1000) {
/* Very small badness. Try a faster bitrate. */
- if (mac->txrates_change)
- memcpy(&oldrates, &mac->txrates, sizeof(oldrates));
default_rate = raise_rate(mac, default_rate);
changes |= IEEE80211SOFTMAC_TXRATECHG_DEFAULT;
default_fallback = get_fallback_rate(mac, default_rate);
@@ -358,8 +388,6 @@
printk("Bitrate raised to %u\n", default_rate);
} else if (mac->txrate_badness >= 10000) {
/* Very high badness. Try a slower bitrate. */
- if (mac->txrates_change)
- memcpy(&oldrates, &mac->txrates, sizeof(oldrates));
default_rate = lower_rate(mac, default_rate);
changes |= IEEE80211SOFTMAC_TXRATECHG_DEFAULT;
default_fallback = get_fallback_rate(mac, default_rate);
@@ -372,7 +400,7 @@
mac->txrates.default_fallback = default_fallback;
if (changes && mac->txrates_change)
- mac->txrates_change(mac->dev, changes, &oldrates);
+ mac->txrates_change(mac->dev, changes);
}
void ieee80211softmac_fragment_lost(struct net_device *dev,
@@ -416,7 +444,11 @@
memcpy(&softnet->supported_rates.rates[softnet->supported_rates.count], net->rates_ex, net->rates_ex_len);
softnet->supported_rates.count += net->rates_ex_len;
sort(softnet->supported_rates.rates, softnet->supported_rates.count, sizeof(softnet->supported_rates.rates[0]), rate_cmp, NULL);
-
+
+ /* we save the ERP value because it is needed at association time, and
+ * many AP's do not include an ERP IE in the association response. */
+ softnet->erp_value = net->erp_value;
+
softnet->capabilities = net->capability;
return softnet;
}
diff --git a/net/ieee80211/softmac/ieee80211softmac_priv.h b/net/ieee80211/softmac/ieee80211softmac_priv.h
index fa1f8e3..0642e09 100644
--- a/net/ieee80211/softmac/ieee80211softmac_priv.h
+++ b/net/ieee80211/softmac/ieee80211softmac_priv.h
@@ -116,9 +116,11 @@
struct ieee80211softmac_essid *essid);
/* Rates related */
+void ieee80211softmac_process_erp(struct ieee80211softmac_device *mac,
+ u8 erp_value);
int ieee80211softmac_ratesinfo_rate_supported(struct ieee80211softmac_ratesinfo *ri, u8 rate);
u8 ieee80211softmac_lower_rate_delta(struct ieee80211softmac_device *mac, u8 rate, int delta);
-void ieee80211softmac_init_txrates(struct ieee80211softmac_device *mac);
+void ieee80211softmac_init_bss(struct ieee80211softmac_device *mac);
void ieee80211softmac_recalc_txrates(struct ieee80211softmac_device *mac);
static inline u8 lower_rate(struct ieee80211softmac_device *mac, u8 rate) {
return ieee80211softmac_lower_rate_delta(mac, rate, 1);
@@ -133,6 +135,9 @@
/*** prototypes from _io.c */
int ieee80211softmac_send_mgt_frame(struct ieee80211softmac_device *mac,
void* ptrarg, u32 type, u32 arg);
+int ieee80211softmac_handle_beacon(struct net_device *dev,
+ struct ieee80211_beacon *beacon,
+ struct ieee80211_network *network);
/*** prototypes from _auth.c */
/* do these have to go into the public header? */
@@ -189,6 +194,7 @@
authenticated:1,
auth_desynced_once:1;
+ u8 erp_value; /* Saved ERP value */
u16 capabilities; /* Capabilities bitfield */
u8 challenge_len; /* Auth Challenge length */
char *challenge; /* Challenge Text */