| /* |
| * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &soc { |
| |
| led_flash0: qcom,camera-led-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-led-flash"; |
| qcom,flash-type = <3>; |
| qcom,flash-source = <&gpio_flash>; |
| qcom,torch-source = <&gpio_flash>; |
| status = "disabled"; |
| }; |
| }; |
| &i2c { |
| |
| qcom,camera@20 { |
| compatible = "shinetech,s5k4e1"; |
| reg = <0x20>; |
| qcom,slave-id = <0x20 0x0000 0x4e10>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "SKUAB_ST_s5k4e1"; |
| cam_vdig-supply = <&pm8110_l2>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 8000 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 13 0>, |
| <&msmgpio 21 0>, |
| <&msmgpio 20 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,csi-lane-assign = <0xe4>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,sensor-type = <0>; |
| qcom,cci-master = <0>; |
| }; |
| qcom,camera@78 { |
| compatible = "shinetech,gc0339"; |
| reg = <0x78>; |
| qcom,slave-id = <0x42 0x00 0xc8>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "skuab_shinetech_gc0339"; |
| cam_vdig-supply = <&pm8110_l14>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1800000 1800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1800000 1800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 14 0>, |
| <&msmgpio 15 0>, |
| <&msmgpio 85 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0xe4>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| qcom,camera@1 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x01>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| cam_vdig-supply = <&pm8110_l2>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 8000 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 13 0>, |
| <&msmgpio 21 0>, |
| <&msmgpio 20 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| qcom,camera@2 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x02>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <270>; |
| cam_vdig-supply = <&pm8110_l14>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1800000 1800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1800000 1800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 14 0>, |
| <&msmgpio 15 0>, |
| <&msmgpio 85 0>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| }; |