| /* |
| * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &soc { |
| |
| led_flash0: qcom,camera-led-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-led-flash"; |
| qcom,flash-type = <1>; |
| qcom,flash-source = <&pm8226_flash0>; |
| qcom,torch-source = <&pm8226_torch>; |
| }; |
| }; |
| |
| &cci { |
| |
| actuator0: qcom,actuator@6e { |
| cell-index = <5>; |
| reg = <0x18>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| eeprom2: qcom,eeprom@6b{ |
| cell-index = <2>; |
| reg = <0x6b>; |
| qcom,eeprom-name = "ofilm_oty5f03"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x6c>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <7>; |
| |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <0 0x0 2 0 1 0>; |
| qcom,page2 = <1 0x3d85 2 0x00 1 1>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <0 0x0 2 0 1 0>; |
| qcom,page3 = <1 0x3d86 2 0x0f 1 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <16 0x3d00 2 0 1 0>; |
| qcom,page4 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <0 0x0 2 0 1 0>; |
| qcom,page5 = <1 0x3d85 2 0x10 1 1>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <0 0x0 2 0 1 0>; |
| qcom,page6 = <1 0x3d86 2 0x1f 1 1>; |
| qcom,pageen6 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <16 0x3d00 2 0 1 0>; |
| |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vana-supply = <&pm8226_l19>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <1 0>; |
| qcom,cam-vreg-min-voltage = <0 2850000>; |
| qcom,cam-vreg-max-voltage = <0 2850000>; |
| qcom,cam-vreg-op-mode = <0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>, |
| <&msmgpio 21 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_gpio", |
| "sensor_gpio", "sensor_gpio" , "sensor_clk"; |
| qcom,cam-power-seq-val = "cam_vio", "cam_vana","sensor_gpio_vdig", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby","sensor_cam_mclk" ; |
| qcom,cam-power-seq-cfg-val = <1 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <1 1 10 10 10 5>; |
| }; |
| |
| eeprom3: qcom,eeprom@6c { |
| cell-index = <3>; |
| reg = <0x6c>; |
| qcom,eeprom-name = "sunny_q8v18a"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0x20>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <4>; |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x3d84 2 0xc0 1 1>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <0 0x3d00 2 0 1 0>; |
| qcom,page2 = <1 0x3d88 2 0x7010 2 1>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <0 0x3d00 2 0 1 0>; |
| qcom,page3 = <1 0x3d8A 2 0x70F4 2 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <228 0x7010 2 0 1 1>; |
| |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vdig","cam_vana", "cam_vio"; |
| qcom,cam-vreg-type = <0 1 2>; |
| qcom,cam-vreg-min-voltage = <1200000 2850000 0>; |
| qcom,cam-vreg-max-voltage = <1200000 2850000 0>; |
| qcom,cam-vreg-op-mode = <200000 80000 0>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cam-power-seq-type = "sensor_vreg","sensor_vreg", |
| "sensor_vreg", "sensor_clk", |
| "sensor_gpio", "sensor_gpio"; |
| qcom,cam-power-seq-val = "cam_vdig","cam_vana", |
| "cam_vio", "sensor_cam_mclk", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby"; |
| qcom,cam-power-seq-cfg-val = <1 1 1 24000000 1 1>; |
| qcom,cam-power-seq-delay = <1 1 1 5 5 10>; |
| }; |
| |
| qcom,camera@20 { |
| compatible = "ovti,ov8865"; |
| reg = <0x20>; |
| qcom,slave-id = <0x20 0x300b 0x8865>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom3>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov8865_q8v18a"; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vaf-supply = <&pm8226_l15>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>, |
| <&msmgpio 15 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-af-pwdm = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY", |
| "CAM_AF_PWDM"; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1F>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| |
| qcom,camera@6a { |
| compatible = "ovti,ov5648"; |
| reg = <0x6a>; |
| qcom,slave-id = <0x6c 0x300a 0x5648>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,eeprom-src = <&eeprom2>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "ov5648_oty5f03"; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <1 0>; |
| qcom,cam-vreg-min-voltage = <0 2850000>; |
| qcom,cam-vreg-max-voltage = <0 2850000>; |
| qcom,cam-vreg-op-mode = <0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>, |
| <&msmgpio 23 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x00>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,mount-angle = <90>; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| cam_vaf-supply = <&pm8226_l15>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000 2800000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 37 0>, |
| <&msmgpio 36 0>, |
| <&msmgpio 15 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-af-pwdm = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY", |
| "CAM_AF_PWDM"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x01>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <270>; |
| cam_vdig-supply = <&pm8226_l5>; |
| cam_vana-supply = <&pm8226_l19>; |
| cam_vio-supply = <&pm8226_lvs1>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 26 0>, |
| <&msmgpio 28 0>, |
| <&msmgpio 35 0>, |
| <&msmgpio 23 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-vdig = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY", |
| "CAM_VDIG"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| }; |