| /* |
| * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &soc { |
| led_flash0: qcom,camera-led-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-led-flash"; |
| qcom,flash-type = <1>; |
| qcom,flash-source = <&pm8941_flash0 &pm8941_flash1>; |
| qcom,torch-source = <&pm8941_torch>; |
| }; |
| }; |
| |
| &cci { |
| |
| actuator0: qcom,actuator@18 { |
| cell-index = <0>; |
| reg = <0x18>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| actuator1: qcom,actuator@36 { |
| cell-index = <1>; |
| reg = <0x36>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| qcom,camera@6e { |
| compatible = "qcom,s5k3l1yx"; |
| reg = <0x6e>; |
| qcom,slave-id = <0x6e 0x0 0x3121>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "s5k3l1yx"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 15 0>, |
| <&msmgpio 90 0>, |
| <&msmgpio 89 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 30000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1F>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@20 { |
| compatible = "qcom,imx135"; |
| reg = <0x20>; |
| qcom,slave-id = <0x20 0x0016 0x0135>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <270>; |
| qcom,sensor-name = "imx135"; |
| qcom,actuator-src = <&actuator1>; |
| qcom,led-flash-src = <&led_flash0>; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 15 0>, |
| <&msmgpio 90 0>, |
| <&msmgpio 89 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 30000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x1F>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,sensor-type = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@6c { |
| compatible = "qcom,ov2720"; |
| reg = <0x6c>; |
| qcom,slave-id = <0x6c 0x300A 0x2720>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <2>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov2720"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio"; |
| qcom,cam-vreg-type = <0 0 1>; |
| qcom,cam-vreg-min-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-max-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-op-mode = <105000 80000 0>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 17 0>, |
| <&msmgpio 18 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x7>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@90 { |
| compatible = "qcom,mt9m114"; |
| reg = <0x90>; |
| qcom,slave-id = <0x90 0x0 0x2481>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <0>; |
| qcom,sensor-name = "mt9m114"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio"; |
| qcom,cam-vreg-type = <0 0 1>; |
| qcom,cam-vreg-min-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-max-voltage = <1225000 2850000 0>; |
| qcom,cam-vreg-op-mode = <105000 80000 0>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 16 0>, |
| <&msmgpio 92 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <270>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,vdd-cx-supply = <&pm8841_s2>; |
| qcom,vdd-cx-name = "qcom,vdd-cx"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| gpios = <&msmgpio 15 0>, |
| <&msmgpio 90 0>, |
| <&msmgpio 89 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x1>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| qcom,vdd-cx-supply = <&pm8841_s2>; |
| qcom,vdd-cx-name = "qcom,vdd-cx"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| gpios = <&msmgpio 17 0>, |
| <&msmgpio 18 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1"; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera"; |
| reg = <0x2>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <2>; |
| qcom,vdd-cx-supply = <&pm8841_s2>; |
| qcom,vdd-cx-name = "qcom,vdd-cx"; |
| cam_vdig-supply = <&pm8941_l3>; |
| cam_vana-supply = <&pm8941_l17>; |
| cam_vio-supply = <&pm8941_lvs3>; |
| cam_vaf-supply = <&pm8941_l23>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 1 0 0>; |
| qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000 100000>; |
| gpios = <&msmgpio 17 0>, |
| <&msmgpio 18 0>, |
| <&msmgpio 28 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| }; |
| }; |