pcmcia: introduce autoconfiguration feature
Introduce an autoconfiguration feature to set certain values in
pcmcia_loop_config(), instead of copying the same code over and over
in each PCMCIA driver. At first, introduce the following options:
CONF_AUTO_CHECK_VCC check or matching Vcc entry
CONF_AUTO_SET_VPP set Vpp
CONF_AUTO_AUDIO enable the speaker line
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> (for drivers/bluetooth)
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index f361d28..17f1040 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -287,7 +287,6 @@
static int axnet_configcheck(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
int i;
diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c
index f6865ad..c1479e3 100644
--- a/drivers/net/pcmcia/fmvj18x_cs.c
+++ b/drivers/net/pcmcia/fmvj18x_cs.c
@@ -322,7 +322,6 @@
static int fmvj18x_ioprobe(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
return 0; /* strange, but that's what the code did already before... */
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index 4a3b6a4..12b028c 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -503,7 +503,6 @@
static int pcnet_confcheck(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
int *priv = priv_data;
diff --git a/drivers/net/pcmcia/smc91c92_cs.c b/drivers/net/pcmcia/smc91c92_cs.c
index 8c16ba6..e127d2b 100644
--- a/drivers/net/pcmcia/smc91c92_cs.c
+++ b/drivers/net/pcmcia/smc91c92_cs.c
@@ -420,7 +420,6 @@
static int mhz_mfc_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cf,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
int k;
@@ -590,7 +589,6 @@
static int smc_configcheck(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cf,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
p_dev->resource[0]->start = cf->io.win[0].base;
diff --git a/drivers/net/pcmcia/xirc2ps_cs.c b/drivers/net/pcmcia/xirc2ps_cs.c
index 7a4a99b..2bc2eb8 100644
--- a/drivers/net/pcmcia/xirc2ps_cs.c
+++ b/drivers/net/pcmcia/xirc2ps_cs.c
@@ -668,7 +668,6 @@
xirc2ps_config_modem(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cf,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
unsigned int ioaddr;
@@ -688,7 +687,6 @@
xirc2ps_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cf,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
int *pass = priv_data;
@@ -826,7 +824,8 @@
* the Mako if (on the first pass) the COR bit 5 is set.
*/
for (pass=0; pass < 2; pass++)
- if (!pcmcia_loop_config(link, xirc2ps_config_check, &pass))
+ if (!pcmcia_loop_config(link, xirc2ps_config_check,
+ &pass))
goto port_found;
/* if special option:
* try to configure as Ethernet only.
diff --git a/drivers/net/wireless/airo_cs.c b/drivers/net/wireless/airo_cs.c
index 5939d0c..63bf662 100644
--- a/drivers/net/wireless/airo_cs.c
+++ b/drivers/net/wireless/airo_cs.c
@@ -140,25 +140,11 @@
static int airo_cs_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
return -ENODEV;
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO)
- p_dev->config_flags |= CONF_ENABLE_SPKR;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
- else if (dflt->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = dflt->vpp1.param[CISTPL_POWER_VNOM]/10000;
-
- p_dev->config_flags |= CONF_ENABLE_IRQ;
-
/* IO window settings */
p_dev->resource[0]->end = p_dev->resource[1]->end = 0;
if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
@@ -193,6 +179,9 @@
dev_dbg(&link->dev, "airo_config\n");
+ link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_VPP |
+ CONF_AUTO_AUDIO;
+
/*
* In this loop, we scan the CIS for configuration table
* entries, each of which describes a valid card
diff --git a/drivers/net/wireless/atmel_cs.c b/drivers/net/wireless/atmel_cs.c
index 080266e..812decd 100644
--- a/drivers/net/wireless/atmel_cs.c
+++ b/drivers/net/wireless/atmel_cs.c
@@ -157,25 +157,11 @@
static int atmel_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
return -ENODEV;
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO)
- p_dev->config_flags |= CONF_ENABLE_SPKR;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000;
- else if (dflt->vpp1.present & (1<<CISTPL_POWER_VNOM))
- p_dev->vpp = dflt->vpp1.param[CISTPL_POWER_VNOM]/10000;
-
- p_dev->config_flags |= CONF_ENABLE_IRQ;
-
/* IO window settings */
p_dev->resource[0]->end = p_dev->resource[1]->end = 0;
if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
@@ -207,6 +193,9 @@
dev_dbg(&link->dev, "atmel_config\n");
+ link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_VPP |
+ CONF_AUTO_AUDIO;
+
/*
In this loop, we scan the CIS for configuration table entries,
each of which describes a valid card configuration, including
diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c
index 5b0b582..d4f19af 100644
--- a/drivers/net/wireless/hostap/hostap_cs.c
+++ b/drivers/net/wireless/hostap/hostap_cs.c
@@ -472,7 +472,6 @@
static int prism2_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
@@ -481,28 +480,6 @@
PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X "
"(default 0x%02X)\n", cfg->index, dflt->index);
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO)
- p_dev->config_flags |= CONF_ENABLE_SPKR;
-
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping"
- " this entry\n");
- return -ENODEV;
- }
- } else if (dflt->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM] /
- 10000 && !ignore_cis_vcc) {
- PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch "
- "- skipping this entry\n");
- return -ENODEV;
- }
- }
-
if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
p_dev->vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
else if (dflt->vpp1.present & (1 << CISTPL_POWER_VNOM))
@@ -553,6 +530,10 @@
}
/* Look for an appropriate configuration table entry in the CIS */
+ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_AUDIO |
+ CONF_AUTO_CHECK_VCC;
+ if (ignore_cis_vcc)
+ link->config_flags &= ~CONF_AUTO_CHECK_VCC;
ret = pcmcia_loop_config(link, prism2_config_check, NULL);
if (ret) {
if (!ignore_cis_vcc)
diff --git a/drivers/net/wireless/libertas/if_cs.c b/drivers/net/wireless/libertas/if_cs.c
index 6020c19..031f3e6 100644
--- a/drivers/net/wireless/libertas/if_cs.c
+++ b/drivers/net/wireless/libertas/if_cs.c
@@ -797,7 +797,6 @@
static int if_cs_ioprobe(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
diff --git a/drivers/net/wireless/orinoco/orinoco_cs.c b/drivers/net/wireless/orinoco/orinoco_cs.c
index 00316a1..b921738 100644
--- a/drivers/net/wireless/orinoco/orinoco_cs.c
+++ b/drivers/net/wireless/orinoco/orinoco_cs.c
@@ -145,39 +145,11 @@
static int orinoco_cs_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
goto next_entry;
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "%s: Vcc mismatch (vcc = %d, CIS = %d)\n",
- __func__, vcc,
- cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- } else if (dflt->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "%s: Vcc mismatch (vcc = %d, CIS = %d)\n",
- __func__, vcc,
- dflt->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- }
-
- if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
- p_dev->vpp =
- cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
- else if (dflt->vpp1.present & (1 << CISTPL_POWER_VNOM))
- p_dev->vpp =
- dflt->vpp1.param[CISTPL_POWER_VNOM] / 10000;
-
/* Do we need to allocate an interrupt? */
p_dev->config_flags |= CONF_ENABLE_IRQ;
@@ -230,6 +202,9 @@
* and most client drivers will only use the CIS to fill in
* implementation-defined details.
*/
+ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC;
+ if (ignore_cis_vcc)
+ link->config_flags &= ~CONF_AUTO_CHECK_VCC;
ret = pcmcia_loop_config(link, orinoco_cs_config_check, NULL);
if (ret) {
if (!ignore_cis_vcc)
diff --git a/drivers/net/wireless/orinoco/spectrum_cs.c b/drivers/net/wireless/orinoco/spectrum_cs.c
index ca2c6c0..f462c78 100644
--- a/drivers/net/wireless/orinoco/spectrum_cs.c
+++ b/drivers/net/wireless/orinoco/spectrum_cs.c
@@ -207,32 +207,11 @@
static int spectrum_cs_config_check(struct pcmcia_device *p_dev,
cistpl_cftable_entry_t *cfg,
cistpl_cftable_entry_t *dflt,
- unsigned int vcc,
void *priv_data)
{
if (cfg->index == 0)
goto next_entry;
- /* Use power settings for Vcc and Vpp if present */
- /* Note that the CIS values need to be rescaled */
- if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "%s: Vcc mismatch (vcc = %d, CIS = %d)\n",
- __func__, vcc,
- cfg->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- } else if (dflt->vcc.present & (1 << CISTPL_POWER_VNOM)) {
- if (vcc != dflt->vcc.param[CISTPL_POWER_VNOM] / 10000) {
- DEBUG(2, "%s: Vcc mismatch (vcc = %d, CIS = %d)\n",
- __func__, vcc,
- dflt->vcc.param[CISTPL_POWER_VNOM] / 10000);
- if (!ignore_cis_vcc)
- goto next_entry;
- }
- }
-
if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM))
p_dev->vpp =
cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000;
@@ -292,6 +271,9 @@
* and most client drivers will only use the CIS to fill in
* implementation-defined details.
*/
+ link->config_flags |= CONF_AUTO_SET_VPP | CONF_AUTO_CHECK_VCC;
+ if (ignore_cis_vcc)
+ link->config_flags &= ~CONF_AUTO_CHECK_VCC;
ret = pcmcia_loop_config(link, spectrum_cs_config_check, NULL);
if (ret) {
if (!ignore_cis_vcc)