Merge "msm: mdss: update kernel to support autogenerated dtsi files"
diff --git a/Documentation/devicetree/bindings/fb/mdss-dsi-ctrl.txt b/Documentation/devicetree/bindings/fb/mdss-dsi-ctrl.txt
index ce4972a..4cec0cd 100644
--- a/Documentation/devicetree/bindings/fb/mdss-dsi-ctrl.txt
+++ b/Documentation/devicetree/bindings/fb/mdss-dsi-ctrl.txt
@@ -12,21 +12,41 @@
- vdda-supply: Phandle for vreg regulator device node.
- qcom,mdss-fb-map: pHandle that specifies the framebuffer to which the
interface is mapped.
+- qcom,platform-regulator-settings: An array of length 7 that specifies the PHY
+ regulator settings.
+- qcom,platform-strength-ctrl: An array of length 2 that specifies the PHY
+ strengthCtrl settings.
+- qcom,platform-bist-ctrl: An array of length 6 that specifies the PHY
+ BIST ctrl settings.
+- qcom,platform-lane-config: An array of length 45 that specifies the PHY
+ lane configuration settings.
Optional properties:
- label: A string used to describe the controller used.
-- qcom,supply-names: A list of strings that lists the names of the
- regulator supplies.
-- qcom,supply-min-voltage-level: A list that specifies minimum voltage level
- of supply(ies) mentioned above. This list maps
- in the order of the supply names listed above.
-- qcom,supply-max-voltage-level: A list that specifies maximum voltage level of
- supply(ies) mentioned above. This list maps in
- the order of the supply names listed above.
-- qcom,supply-peak-current: A list that specifies the peak current that will
- be drawn from the supply(ies) mentioned above. This
- list maps in the order of the supply names listed above.
+- qcom,platform-supply-entry<1..n>: A node that lists the elements of the supply. There
+ can be more than one instance of this binding,
+ in which case the entry would be appended with
+ the supply entry index.
+ e.g. qcom,platform-supply-entry1
+ -- qcom,supply-name: name of the supply (vdd/vdda/vddio)
+ -- qcom,supply-min-voltage: minimum voltage level (uV)
+ -- qcom,supply-max-voltage: maximum voltage level (uV)
+ -- qcom,supply-enable-load: load drawn (uA) from enabled supply
+ -- qcom,supply-disable-load: load drawn (uA) from disabled supply
+ -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
+ -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
+ -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
+ -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
+- qcom,platform-enable-gpio: Specifies the panel lcd/display enable gpio.
+- qcom,platform-reset-gpio: Specifies the panel reset gpio.
+- qcom,platform-te-gpio: Specifies the gpio used for TE.
+- qcom,platform-reset-sequence: An array that lists the
+ sequence of reset gpio values and sleeps
+ Each command will have the format defined
+ as below:
+ --> Reset GPIO value
+ --> Sleep value (in ms)
Example:
mdss_dsi0: qcom,mdss_dsi@fd922800 {
@@ -37,9 +57,50 @@
vdd-supply = <&pm8226_l15>;
vddio-supply = <&pm8226_l8>;
vdda-supply = <&pm8226_l4>;
- qcom,supply-names = "vdd", "vddio", "vdda";
- qcom,supply-min-voltage-level = <2800000 1800000 1200000>;
- qcom,supply-max-voltage-level = <2800000 1800000 1200000>;
- qcom,supply-peak-current = <150000 100000 100000>;
+ qcom,platform-strength-ctrl = [ff 06];
+ qcom,platform-bist-ctrl = [00 00 b1 ff 00 00];
+ qcom,platform-regulator-settings = [07 09 03 00 20 00 01];
+ qcom,platform-lane-config = [00 00 00 00 00 00 00 01 97
+ 00 00 00 00 05 00 00 01 97
+ 00 00 00 00 0a 00 00 01 97
+ 00 00 00 00 0f 00 00 01 97
+ 00 c0 00 00 00 00 00 01 bb];
qcom,mdss-fb-map = <&mdss_fb0>;
+ qcom,platform-reset-gpio = <&msmgpio 25 1>;
+ qcom,platform-te-gpio = <&msmgpio 24 0>;
+ qcom,platform-enable-gpio = <&msmgpio 58 1>;
+ qcom,platform-reset-sequence = <1 25 0 20 1 10>;
+ qcom,platform-supply-entry1 {
+ qcom,supply-name = "vdd";
+ qcom,supply-min-voltage = <2800000>;
+ qcom,supply-max-voltage = <2800000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <20>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <20>;
+ };
+ qcom,platform-supply-entry2 {
+ qcom,supply-name = "vddio";
+ qcom,supply-min-voltage = <1800000>;
+ qcom,supply-max-voltage = <1800000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <30>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <30>;
+ };
+ qcom,platform-supply-entry3 {
+ qcom,supply-name = "vdda";
+ qcom,supply-min-voltage = <1200000>;
+ qcom,supply-max-voltage = <1200000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <20>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <30>;
+ };
};
diff --git a/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt b/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
index 8c87eac..44134f8 100644
--- a/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
+++ b/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
@@ -12,140 +12,173 @@
the panel driver. By default this property will be
set to "disable". Will be set to "ok/okay" status
for specific platforms.
-- qcom,dsi-ctrl-phandle: Specifies the phandle for the DSI controller that
+- qcom,mdss-dsi-panel-controller: Specifies the phandle for the DSI controller that
this panel will be mapped to.
-- qcom,mdss-pan-res: A two dimensional array that specifies the panel
- resolution.
-- qcom,mdss-pan-bpp: Specifies the panel bits per pixel. Default value is 24(rgb888).
- 18 = for rgb666
+- qcom,mdss-dsi-panel-width: Specifies panel width in pixels.
+- qcom,mdss-dsi-panel-height: Specifies panel height in pixels.
+- qcom,mdss-dsi-bpp: Specifies the panel bits per pixel.
+ 3 = for rgb111
+ 8 = for rgb332
+ 12 = for rgb444
16 = for rgb565
-- qcom,mdss-pan-dest: A string that specifies the destination display for the panel.
- Default is "display_1".
+ 18 = for rgb666
+ 24 = for rgb888
+- qcom,mdss-dsi-panel-destination: A string that specifies the destination display for the panel.
"display_1" = DISPLAY_1
"display_2" = DISPLAY_2
-- qcom,panel-phy-regulatorSettings: An array of length 7 that specifies the PHY
- regulator settings for the panel.
-- qcom,panel-phy-timingSettings: An array of length 12 that specifies the PHY
+- qcom,mdss-dsi-panel-timings: An array of length 12 that specifies the PHY
timing settings for the panel.
-- qcom,panel-phy-strengthCtrl: An array of length 2 that specifies the PHY
- strengthCtrl settings for the panel.
-- qcom,panel-phy-bistCtrl: An array of length 6 that specifies the PHY
- BIST ctrl settings for the panel.
-- qcom,panel-phy-laneConfig: An array of length 45 that specifies the PHY
- lane configuration settings for the panel.
-- qcom,mdss-panel-on-cmds: An array of variable length that lists the init commands
- of the panel. Each command will have the format specified
- as below:
- --> data type of the command
- --> specifies whether this command packet is last.
- --> virtual channel
- --> Needs acknowledge from the panel or not.
- --> wait time after the command is transmitter.
- --> size of payload
- --> payload.
-- qcom,mdss-panel-off-cmds: An array of variable length that lists the panel off
- commands. Each command will have the format specified
- as below:
- --> data type of the command
- --> specifies whether this command packet is last.
- --> virtual channel
- --> Needs acknowledge from the panel or not.
- --> wait time after the command is transmitter.
- --> size of payload
- --> payload.
+- qcom,mdss-dsi-on-command: A byte stream formed by multiple dcs packets base on
+ qcom dsi controller protocol.
+ byte 0: dcs data type
+ byte 1: set to indicate this is an individual packet
+ (no chain)
+ byte 2: virtual channel number
+ byte 3: expect ack from client (dcs read command)
+ byte 4: wait number of specified ms after dcs command
+ transmitted
+ byte 5, 6: 16 bits length in network byte order
+ byte 7 and beyond: number byte of payload
+- qcom,mdss-dsi-off-command: A byte stream formed by multiple dcs packets base on
+ qcom dsi controller protocol.
+ byte 0: dcs data type
+ byte 1: set to indicate this is an individual packet
+ (no chain)
+ byte 2: virtual channel number
+ byte 3: expect ack from client (dcs read command)
+ byte 4: wait number of specified ms after dcs command
+ transmitted
+ byte 5, 6: 16 bits length in network byte order
+ byte 7 and beyond: number byte of payload
Optional properties:
-- label: A string used as a descriptive name of the panel
-- qcom,enable-gpio: Specifies the panel lcd/display enable gpio.
-- qcom,rst-gpio: Specifies the panel reset gpio.
-- qcom,te-gpio: Specifies the gpio used for TE.
-- qcom,pwm-lpg-channel: LPG channel for backlight.
-- qcom,pwm-period: PWM period in microseconds.
-- qcom,pwm-pmic-gpio: PMIC gpio binding to backlight.
-- qcom,mdss-pan-broadcast-mode: Boolean used to enable broadcast mode.
+- qcom,mdss-dsi-panel-name: A string used as a descriptive name of the panel
- qcom,cont-splash-enabled: Boolean used to enable continuous splash mode.
-- qcom,fbc-enabled: Boolean used to enable frame buffer compression mode.
-- qcom,fbc-mode-select: An array of length 7 that specifies the fbc mode supported
- by the panel. FBC enabled panels may or may not support
- the modes specified here. Each entry will
- have the format specified below:
- --> compressed bpp supported by the panel
- --> component packing
- --> enable/disable quantization error calculation
- --> Bias for CD
- --> enable/disable PAT mode
- --> enable/disable VLC mode
- --> enable/disable BFLC mode
-- qcom,fbc-budget-ctl: An array of length 3 that specifies the budget control settings
- supported by the fbc enabled panel. Each entry will have the format
- specified below:
- --> per line extra budget
- --> extra budget level
- --> per block budget
-- qcom,fbc-lossy-mode: An array of 3 that specifies the lossy mode settings
- supported by the fbc enabled panel. Each entry will
- have the format specified below:
- --> lossless mode threshold
- --> lossy mode threshold
- --> lossy RGB threshold
-- qcom,mdss-pan-porch-values: An array of size 6 that specifies the panel blanking values.
-- qcom,mdss-pan-underflow-clr: Specifies the controller settings for the panel underflow clear
- settings. Default value is 0xff.
-- qcom,mdss-pan-bl-ctrl: A string that specifies the implementation of backlight
+- qcom,mdss-dsi-panel-broadcast-mode: Boolean used to enable broadcast mode.
+- qcom,mdss-dsi-fbc-enable: Boolean used to enable frame buffer compression mode.
+- qcom,mdss-dsi-fbc-bpp: Compressed bpp supported by the panel.
+ Specified color order is used as default value.
+- qcom,mdss-dsi-fbc-packing: Component packing.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-quant-error: Boolean used to enable quantization error calculation.
+- qcom,mdss-dsi-fbc-bias: Bias for CD.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-pat-mode: Boolean used to enable PAT mode.
+- qcom,mdss-dsi-fbc-vlc-mode: Boolean used to enable VLC mode.
+- qcom,mdss-dsi-fbc-bflc-mode: Boolean used to enable BFLC mode.
+- qcom,mdss-dsi-fbc-h-line-budget: Per line extra budget.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-budget-ctrl: Extra budget level.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-block-budget: Per block budget.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-lossless-threshold: Lossless mode threshold.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-lossy-threshold: Lossy mode threshold.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-rgb-threshold: Lossy RGB threshold.
+ 0 = default value.
+- qcom,mdss-dsi-fbc-lossy-mode-idx: Lossy mode index value.
+ 0 = default value.
+- qcom,mdss-dsi-h-back-porch: Horizontal back porch value in pixel.
+ 6 = default value.
+- qcom,mdss-dsi-h-front-porch: Horizontal front porch value in pixel.
+ 6 = default value.
+- qcom,mdss-dsi-h-pulse-width: Horizontal pulse width.
+ 2 = default value.
+- qcom,mdss-dsi-h-sync-skew: Horizontal sync skew value.
+ 0 = default value.
+- qcom,mdss-dsi-v-back-porch: Vertical back porch value in pixel.
+ 6 = default value.
+- qcom,mdss-dsi-v-front-porch: Vertical front porch value in pixel.
+ 6 = default value.
+- qcom,mdss-dsi-v-pulse-width: Vertical pulse width.
+ 2 = default value.
+- qcom,mdss-dsi-h-left-border: Horizontal left border in pixel.
+ 0 = default value
+- qcom,mdss-dsi-h-right-border: Horizontal right border in pixel.
+ 0 = default value
+- qcom,mdss-dsi-v-top-border: Vertical top border in pixel.
+ 0 = default value
+- qcom,mdss-dsi-v-bottom-border: Vertical bottom border in pixel.
+ 0 = default value
+- qcom,mdss-dsi-underflow-color: Specifies the controller settings for the
+ panel under flow color.
+ 0xff = default value.
+- qcom,mdss-dsi-border-color: Defines the border color value if border is present.
+ 0 = default value.
+- qcom,mdss-dsi-bl-pmic-control-type: A string that specifies the implementation of backlight
control for this panel.
"bl_ctrl_pwm" = Backlight controlled by PWM gpio.
"bl_ctrl_wled" = Backlight controlled by WLED.
- "bl_ctrl_dcs_cmds" = Backlight controlled by DCS commands.
-- qcom,mdss-pan-bl-levels: Specifies the backlight levels supported by the panel.
- Default range is 1 to 255.
-
-- qcom,mdss-pan-dsi-mode: Specifies the panel operating mode.
- 0 = enable video mode(default mode).
- 1 = enable command mode.
-- qcom,mdss-vsync-enable: Specifies Tear Check configuration.
- 0 = TE disable.
- 1 = TE enable.
-- qcom,mdss-hw-vsync-mode: Specifies TE type.
- 0 = software vsync.
- 1 = hardware vsync (TE gpio pin).
-- qcom,mdss-pan-te-sel: Specifies TE operating mode.
+ "bl_ctrl_dcs" = Backlight controlled by DCS commands.
+ other: Unknown backlight control. (default)
+- qcom,mdss-dsi-bl-pmic-bank-select: LPG channel for backlight.
+ Requred if blpmiccontroltype is PWM
+- qcom,mdss-dsi-bl-pmic-pwm-frequency: PWM period in microseconds.
+ Requred if blpmiccontroltype is PWM
+- qcom,mdss-dsi-pwm-gpio: PMIC gpio binding to backlight.
+ Requred if blpmiccontroltype is PWM
+- qcom,mdss-dsi-bl-min-level: Specifies the min backlight level supported by the panel.
+ 0 = default value.
+- qcom,mdss-dsi-bl-max-level: Specifies the max backlight level supported by the panel.
+ 255 = default value.
+- qcom,mdss-dsi-interleave-mode: Specifies interleave mode.
+ 0 = default value.
+- qcom,mdss-dsi-panel-type: Specifies the panel operating mode.
+ "dsi_video_mode" = enable video mode (default).
+ "dsi_cmd_mode" = enable command mode.
+- qcom,mdss-dsi-te-check-enable: Boolean to enable Tear Check configuration.
+- qcom,mdss-dsi-te-using-te-pin: Boolean to specify whether using hardware vsync.
+- qcom,mdss-dsi-te-pin-select: Specifies TE operating mode.
0 = TE through embedded dcs command
- 1 = TE through TE gpio pin.
-- qcom,mdss-pan-dsi-h-pulse-mode: Specifies the pulse mode option for the panel.
+ 1 = TE through TE gpio pin. (default)
+- qcom,mdss-dsi-te-dcs-command: Inserts the dcs command.
+ 1 = default value.
+- qcom,mdss-dsi-te-v-sync-rd-ptr-irq-line: Configures the scan line number that the dsi
+ pixel transfer will start on. Rasing this number
+ will result in delaying the start of the pixel
+ transfer.
+ 0x2c = default value.
+- qcom,mdss-dsi-te-v-sync-continue-lines: Represents the difference in number of lines
+ between estimated read pointer and write pointer
+ to allow the updating of all the lines except
+ the first line of the frame.
+ 0x3c = default value.
+- qcom,mdss-dsi-h-sync-pulse: Specifies the pulse mode option for the panel.
0 = Don't send hsa/he following vs/ve packet(default)
1 = Send hsa/he following vs/ve packet
-- qcom,mdss-pan-dsi-h-power-stop: An Array of size 3 that specifies the power mode
- during horizontal porch and sync periods of the panel.
- 0 = high speed mode(default mode).
- 1 = Low power mode for horizontal porches and sync pulse.
-- qcom,mdss-pan-dsi-bllp-power-stop: An Array of size 2 that specifies the power mode
- during blanking period and after EOF(end of frame).
- 0 = high speed mode(default mode).
- 1 = Low power mode during blanking and EOF.
-- qcom,mdss-pan-dsi-traffic-mode: Specifies the panel traffic mode.
+- qcom,mdss-dsi-hfp-power-mode: Boolean to determine DSI lane state during
+ horizontal front porch (HFP) blanking period.
+- qcom,mdss-dsi-hbp-power-mode: Boolean to determine DSI lane state during
+ horizontal back porch (HBP) blanking period.
+- qcom,mdss-dsi-hsa-power-mode: Boolean to determine DSI lane state during
+ horizontal sync active (HSA) mode.
+- qcom,mdss-dsi-bllp-eof-power-mode: Boolean to determine DSI lane state during
+ blanking low power period (BLLP) EOF mode.
+- qcom,mdss-dsi-bllp-power-mode: Boolean to determine DSI lane state during
+ blanking low power period (BLLP) mode.
+- qcom,mdss-dsi-traffic-mode: Specifies the panel traffic mode.
0 = non burst with sync pulses (default mode).
1 = non burst with sync start event.
2 = burst mode.
-- qcom,mdss-pan-dsi-dst-format: Specifies the destination format.
- 0 = DSI_VIDEO_DST_FORMAT_RGB565.
- 1 = DSI_VIDEO_DST_FORMAT_RGB666.
- 2 = DSI_VIDEO_DST_FORMAT_RGB666_LOOSE.
- 3 = DSI_VIDEO_DST_FORMAT_RGB888 (Default format)
- 6 = DSI_CMD_DST_FORMAT_RGB565
- 7 = DSI_CMD_DST_FORMAT_RGB666
- 8 = DSI_CMD_DST_FORMAT_RGB888
-- qcom,mdss-pan-dsi-vc: Specifies the virtual channel identefier.
+- qcom,mdss-dsi-pixel-packing: Specifies if pixel packing is used (in case of RGB666).
+ 0 = Tight packing (default value).
+ 1 = Loose packing.
+- qcom,mdss-dsi-virtual-channel-id: Specifies the virtual channel identefier.
0 = default value.
-- qcom,mdss-pan-dsi-rgb-swap: Specifies the R, G and B channel ordering.
+- qcom,mdss-dsi-color-order: Specifies the R, G and B channel ordering.
0 = DSI_RGB_SWAP_RGB (default value)
1 = DSI_RGB_SWAP_RBG
2 = DSI_RGB_SWAP_BGR
3 = DSI_RGB_SWAP_BRG
4 = DSI_RGB_SWAP_GRB
5 = DSI_RGB_SWAP_GBR
-- qcom,mdss-pan-dsi-data-lanes: An array that specifies the data lanes enabled.
- <1 1 0 0> = data lanes 1 and 2 are enabled.(default).
-- qcom,mdss-pan-dsi-dlane-swap: Specifies the data lane swap configuration.
+- qcom,mdss-dsi-lane-0-state: Boolean that specifies whether data lane 0 is enabled.
+- qcom,mdss-dsi-lane-1-state: Boolean that specifies whether data lane 1 is enabled.
+- qcom,mdss-dsi-lane-2-state: Boolean that specifies whether data lane 2 is enabled.
+- qcom,mdss-dsi-lane-3-state: Boolean that specifies whether data lane 3 is enabled.
+- qcom,mdss-dsi-lane-map: Specifies the data lane swap configuration.
0 = <0 1 2 3> (default value)
1 = <3 0 1 2>
2 = <2 3 0 1>
@@ -154,79 +187,121 @@
5 = <1 0 3 2>
6 = <2 1 0 3>
7 = <3 2 1 0>
-- qcom,mdss-pan-dsi-t-clk: An array that specifies the byte clock cycles
- before and after each mode switch.
-- qcom,mdss-pan-dsi-stream: Specifies the packet stream to be used.
+- qcom,mdss-dsi-t-clk-post: Specifies the byte clock cycles after mode switch.
+ 0x03 = default value.
+- qcom,mdss-dsi-t-clk-pre: Specifies the byte clock cycles before mode switch.
+ 0x24 = default value.
+- qcom,mdss-dsi-stream: Specifies the packet stream to be used.
0 = stream 0 (default)
1 = stream 1
-- qcom,mdss-pan-dsi-mdp-tr: Specifies the trigger mechanism to be used for MDP path.
+- qcom,mdss-dsi-mdp-trigger: Specifies the trigger mechanism to be used for MDP path.
0 = no trigger
2 = Tear check signal line used for trigger
- 4 = Triggered by software (default mode)
+ 4 = Triggered by software (default)
6 = Software trigger and TE
-- qcom,mdss-pan-dsi-dma-tr: Specifies the trigger mechanism to be used for DMA path.
+- qcom,mdss-dsi-dma-trigger: Specifies the trigger mechanism to be used for DMA path.
0 = no trigger
2 = Tear check signal line used for trigger
- 4 = Triggered by software (default mode)
+ 4 = Triggered by software (default)
5 = Software trigger and start/end of frame trigger.
6 = Software trigger and TE
-- qcom,mdss-pan-dsi-frame-rate: Specifies the frame rate for the panel.
+- qcom,mdss-dsi-panel-framerate: Specifies the frame rate for the panel.
60 = 60 frames per second (default)
-- qcom,on-cmds-dsi-state: A string that Specifies the ctrl state for sending ON commands.
- Supported modes are "DSI_LP_MODE" and "DSI_HS_MODE".
-- qcom,off-cmds-dsi-state: A string that Specifies the ctrl state for sending ON commands.
- Supported modes are "DSI_LP_MODE" and "DSI_HS_MODE".
+- qcom,mdss-dsi-panel-clockrate: Specifies the panel clock speed in Hz.
+ 0 = default value.
+- qcom,mdss-dsi-on-command-state: String that specifies the ctrl state for sending ON commands.
+ "dsi_lp_mode" = DSI low power mode (default)
+ "dsi_hs_mode" = DSI high speed mode
+- qcom,mdss-dsi-off-command-state: String that specifies the ctrl state for sending OFF commands.
+ "dsi_lp_mode" = DSI low power mode (default)
+ "dsi_hs_mode" = DSI high speed mode
-- qcom,panel-on-cmds: A byte stream formed by multiple dcs packets base on
- qcom dsi controller protocol.
- byte 0 : dcs data type
- byte 1 : set to indicate this is an individual packet
- (no chain).
- byte 2 : virtual channel number
- byte 3 : expect ack from client (dcs read command)
- byte 4 : wait number of specified ms after dcs command
- transmitted
- byte 5, 6: 16 bits length in network byte order
- byte 7 and beyond: number byte of payload
-
Note, if a given optional qcom,* binding is not present, then the driver will configure
the default values specified.
Example:
-/ {
+&soc {
qcom,mdss_dsi_sim_video {
compatible = "qcom,mdss-dsi-panel";
- label = "simulator video mode dsi panel";
+ qcom,mdss-dsi-panel-name = "simulator video mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,mdss-pan-res = <640 480>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <6 2 6 6 2 6>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-levels = <1 15>;
- qcom,mdss-pan-dsi-mode = <0>;
- qcom,mdss-pan-dsi-h-pulse-mode = <1>;
- qcom,mdss-pan-dsi-h-power-stop = <1 1 1>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <0>;
- qcom,mdss-pan-dsi-dst-format = <3>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 0 0>;
- qcom,mdss-pan-dsi-t-clk = <0x24 0x03>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x04>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-frame-rate = <60>;
- qcom,panel-on-cmds = [32 01 00 00 00 00 02 00 00];
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [22 01 00 00 00 00 00];
- qcom,off-cmds-dsi-state = "DSI LP MODE";
- qcom,fbc-enabled;
- qcom,fbc-mode = <12 0 1 2 1 1 1>;
- qcom,fbc-budget-ctl = <675 5 91>;
- qcom,fbc-lossy-mode = <0 0xc0 0 3>;
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-height = <1280>;
+ qcom,mdss-dsi-panel-width = <720>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-pixel-packing = <0>;
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-broadcast-mode;
+ qcom,mdss-dsi-fbc-enable;
+ qcom,mdss-dsi-fbc-bpp = <0>;
+ qcom,mdss-dsi-fbc-packing = <0>;
+ qcom,mdss-dsi-fbc-quant-error;
+ qcom,mdss-dsi-fbc-bias = <0>;
+ qcom,mdss-dsi-fbc-pat-mode;
+ qcom,mdss-dsi-fbc-vlc-mode;
+ qcom,mdss-dsi-fbc-bflc-mode;
+ qcom,mdss-dsi-fbc-h-line-budget = <0>;
+ qcom,mdss-dsi-fbc-budget-ctrl = <0>;
+ qcom,mdss-dsi-fbc-block-budget = <0>;
+ qcom,mdss-dsi-fbc-lossless-threshold = <0>;
+ qcom,mdss-dsi-fbc-lossy-threshold = <0>;
+ qcom,mdss-dsi-fbc-rgb-threshold = <0>;
+ qcom,mdss-dsi-fbc-lossy-mode-idx = <0>;
+ qcom,mdss-dsi-h-front-porch = <140>;
+ qcom,mdss-dsi-h-back-porch = <164>;
+ qcom,mdss-dsi-h-pulse-width = <8>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <6>;
+ qcom,mdss-dsi-v-front-porch = <1>;
+ qcom,mdss-dsi-v-pulse-width = <1>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = < 15>;
+ qcom,mdss-dsi-interleave-mode = <0>;
+ qcom,mdss-dsi-panel-type = "dsi_video_mode";
+ qcom,mdss-dsi-te-check-enable;
+ qcom,mdss-dsi-te-using-te-pin;
+ qcom,mdss-dsi-te-dcs-command = <1>;
+ qcom,mdss-dsi-te-v-sync-continue-lines = <0x3c>;
+ qcom,mdss-dsi-te-v-sync-rd-ptr-irq-line = <0x2c>;
+ qcom,mdss-dsi-te-pin-select = <1>;
+ qcom,mdss-dsi-h-sync-pulse = <1>;
+ qcom,mdss-dsi-hfp-power-mode;
+ qcom,mdss-dsi-hbp-power-mode;
+ qcom,mdss-dsi-hsa-power-mode;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-traffic-mode = <0>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-t-clk-post = <0x20>;
+ qcom,mdss-dsi-t-clk-pre = <0x2c>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-mdp-trigger = <0>;
+ qcom,mdss-dsi-dma-trigger = <0>;
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-panel-clockrate = <424000000>;
+ qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33
+ 22 27 1e 03 04 00];
+ qcom,mdss-dsi-on-command = [32 01 00 00 00 00 02 00 00
+ 29 01 00 00 10 00 02 FF 99];
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00];
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
+ qcom,mdss-dsi-bl-pmic-bank-select = <0>;
+ qcom,mdss-dsi-bl-pmic-pwm-frequency = <0>;
+ qcom,mdss-dsi-pwm-gpio = <&pm8941_mpps 5 0>;
};
};
diff --git a/arch/arm/boot/dts/dsi-panel-hx8394a-720p-video.dtsi b/arch/arm/boot/dts/dsi-panel-hx8394a-720p-video.dtsi
index 25c1851..c8d150a 100644
--- a/arch/arm/boot/dts/dsi-panel-hx8394a-720p-video.dtsi
+++ b/arch/arm/boot/dts/dsi-panel-hx8394a-720p-video.dtsi
@@ -10,98 +10,76 @@
* GNU General Public License for more details.
*/
+/*---------------------------------------------------------------------------
+ * This file is autogenerated file using gcdb parser. Please do not edit it.
+ * Update input XML file to add a new entry or update variable in this file
+ * VERSION = "1.0"
+ *---------------------------------------------------------------------------*/
&soc {
qcom,mdss_dsi_hx8394a_720p_video {
compatible = "qcom,mdss-dsi-panel";
- label = "hx8394a 720p video mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,rst-gpio = <&msmgpio 25 0>;
- qcom,mdss-pan-res = <720 1280>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <59 60 79 10 2 7>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
- qcom,mdss-pan-bl-levels = <1 4095>;
- qcom,mdss-pan-dsi-mode = <0>;
- qcom,mdss-pan-dsi-h-pulse-mode = <1>;
- qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <2>;
- qcom,mdss-pan-dsi-dst-format = <3>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 1 1>; /* 4 lanes */
- qcom,mdss-pan-dsi-dlane-swap = <0>;
- qcom,mdss-pan-dsi-t-clk = <0x2d 0x1f>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x0>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-dsi-frame-rate = <60>;
- qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regualotor settings */
- 20 00 01];
- qcom,panel-phy-timingSettings = [8d 24 19 00 34 34
- 1d 26 2a 03 04 00];
- qcom,panel-phy-strengthCtrl = [ff 06];
- qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
- 00 00];
- qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
- 00 00 00 00 05 00 00 01 97 /* lane1 config */
- 00 00 00 00 0a 00 00 01 97 /* lane2 config */
- 00 00 00 00 0f 00 00 01 97 /* lane3 config */
- 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
- qcom,panel-on-cmds = [39 01 00 00 00 00 04
- b9 ff 83 94
- 39 01 00 00 00 00 05
- c7 00 10 00 10
- 39 01 00 00 00 00 02
- bc 07
- 39 01 00 00 00 00 02
- ba 13
- 39 01 00 00 00 00 10
- b1 01 00 07 83 01
- 12 0f 32 38 29 29
- 50 02 00 00
- 39 01 00 00 00 00 07
- b2 00 c8 09 05 00
- 71
- 39 01 00 00 00 00 02
- cc 05
- 05 01 00 00 00 00 02 00 00
- 39 01 00 00 00 00 35
- d5 00 00 00 00 0a
- 00 01 00 00 00 33
- 00 23 45 67 01 01
- 23 88 88 88 88 88
- 88 88 99 99 99 88
- 88 99 88 54 32 10
- 76 32 10 88 88 88
- 88 88 88 88 99 99
- 99 88 88 88 99
- 39 01 00 00 00 00 17
- b4 80 08 32 10 00
- 32 15 08 32 12 20
- 33 05 4c 05 37 05
- 3f 1e 5f 5f 06
- 39 01 00 00 00 00 02
- b6 00
- 39 01 00 00 00 00 23
- e0 01 05 07 25 35
- 3f 0b 32 04 09 0e
- 10 13 10 14 16 1b
- 01 05 07 25 35 3f
- 0b 32 04 09 0e 10
- 13 10 14 16 1b
- 05 01 00 00 00 00 02 00 00
- 39 01 00 00 00 00 04
- bf 06 00 10
- 05 01 00 00 c8 00 02 11 00
- 05 01 00 00 32 00 02 29 00];
+ qcom,mdss-dsi-panel-name = "hx8394a 720p video mode dsi panel";
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-type = "dsi_video_mode";
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-panel-width = <720>;
+ qcom,mdss-dsi-panel-height = <1280>;
+ qcom,mdss-dsi-h-front-porch = <79>;
+ qcom,mdss-dsi-h-back-porch = <59>;
+ qcom,mdss-dsi-h-pulse-width = <60>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <10>;
+ qcom,mdss-dsi-v-front-porch = <7>;
+ qcom,mdss-dsi-v-pulse-width = <2>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-on-command = [39 01 00 00 00 00 04 b9 ff 83 94
+ 39 01 00 00 00 00 05 c7 00 10 00 10
+ 39 01 00 00 00 00 02 bc 07
+ 39 01 00 00 00 00 02 ba 13
+ 39 01 00 00 00 00 10 b1 01 00 07 83 01 12 0f 32 38 29 29 50 02 00 00
+ 39 01 00 00 00 00 07 b2 00 c8 09 05 00 71
+ 39 01 00 00 00 00 02 cc 05
+ 05 01 00 00 00 00 02 00 00
+ 39 01 00 00 00 00 35 d5 00 00 00 00 0a 00 01 00 00 00 33 00 23 45 67 01 01 23 88 88 88 88 88 88 88 99 99 99 88 88 99 88 54 32 10 76 32 10 88 88 88 88 88 88 88 99 99 99 88 88 88 99
+ 39 01 00 00 00 00 17 b4 80 08 32 10 00 32 15 08 32 12 20 33 05 4c 05 37 05 3f 1e 5f 5f 06
+ 39 01 00 00 00 00 02 b6 00
+ 39 01 00 00 00 00 23 e0 01 05 07 25 35 3f 0b 32 04 09 0e 10 13 10 14 16 1b 01 05 07 25 35 3f 0b 32 04 09 0e 10 13 10 14 16 1b
+ 05 01 00 00 00 00 02 00 00
+ 39 01 00 00 00 00 04 bf 06 00 10
+ 05 01 00 00 c8 00 02 11 00
+ 05 01 00 00 32 00 02 29 00];
+ qcom,mdss-dsi-off-command = [05 01 00 00 0a 00 02 28 00
+ 05 01 00 00 96 00 02 10 00];
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-h-sync-pulse = <1>;
+ qcom,mdss-dsi-traffic-mode = <2>;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-panel-timings = [8d 24 19 00 34 34 1d 26 2a 03 04 00];
+ qcom,mdss-dsi-t-clk-post = <0x1f>;
+ qcom,mdss-dsi-t-clk-pre = <0x2d>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = <4095>;
+ qcom,mdss-dsi-dma-trigger = <4>;
+ qcom,mdss-dsi-mdp-trigger = <0>;
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [05 01 00 00 0a 00 02 28 00
- 05 01 00 00 96 00 02 10 00];
- qcom,off-cmds-dsi-state = "DSI_HS_MODE";
};
};
diff --git a/arch/arm/boot/dts/dsi-panel-nt35590-720p-cmd.dtsi b/arch/arm/boot/dts/dsi-panel-nt35590-720p-cmd.dtsi
index 2a6bbf9..d0b4da8 100644
--- a/arch/arm/boot/dts/dsi-panel-nt35590-720p-cmd.dtsi
+++ b/arch/arm/boot/dts/dsi-panel-nt35590-720p-cmd.dtsi
@@ -10,55 +10,40 @@
* GNU General Public License for more details.
*/
+/*---------------------------------------------------------------------------
+ * This file is autogenerated file using gcdb parser. Please do not edit it.
+ * Update input XML file to add a new entry or update variable in this file
+ * VERSION = "1.0"
+ *---------------------------------------------------------------------------*/
&soc {
qcom,mdss_dsi_nt35590_720p_cmd {
compatible = "qcom,mdss-dsi-panel";
- label = "nt35590 720p command mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,rst-gpio = <&msmgpio 25 0>;
- qcom,te-gpio = <&msmgpio 24 0>;
- qcom,mdss-pan-res = <720 1280>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <164 8 140 1 1 6>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
- qcom,mdss-pan-bl-levels = <1 4095>;
- qcom,mdss-pan-dsi-mode = <1>;
- qcom,mdss-vsync-enable = <1>;
- qcom,mdss-hw-vsync-mode = <1>;
- qcom,mdss-pan-dsi-h-pulse-mode = <1>;
- qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <2>;
- qcom,mdss-pan-dsi-dst-format = <8>;
- qcom,mdss-pan-insert-dcs-cmd = <1>;
- qcom,mdss-pan-wr-mem-continue = <0x3c>;
- qcom,mdss-pan-wr-mem-start = <0x2c>;
- qcom,mdss-pan-te-sel = <1>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 1 1>; /* 4 lanes */
- qcom,mdss-pan-dsi-dlane-swap = <0>;
- qcom,mdss-pan-dsi-t-clk = <0x2c 0x20>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x0>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-dsi-frame-rate = <60>;
- qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regualotor settings */
- 20 00 01];
- qcom,panel-phy-timingSettings = [7d 25 1d 00 37 33
- 22 27 1e 03 04 00];
- qcom,panel-phy-strengthCtrl = [ff 06];
- qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
- 00 00];
- qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
- 00 00 00 00 05 00 00 01 97 /* lane1 config */
- 00 00 00 00 0a 00 00 01 97 /* lane2 config */
- 00 00 00 00 0f 00 00 01 97 /* lane3 config */
- 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
- qcom,panel-on-cmds = [29 01 00 00 00 00 02 FF EE
+ qcom,mdss-dsi-panel-name = "nt35590 720p command mode dsi panel";
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-type = "dsi_cmd_mode";
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-panel-width = <720>;
+ qcom,mdss-dsi-panel-height = <1280>;
+ qcom,mdss-dsi-h-front-porch = <140>;
+ qcom,mdss-dsi-h-back-porch = <164>;
+ qcom,mdss-dsi-h-pulse-width = <8>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <1>;
+ qcom,mdss-dsi-v-front-porch = <6>;
+ qcom,mdss-dsi-v-pulse-width = <1>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-on-command = [29 01 00 00 00 00 02 FF EE
29 01 00 00 00 00 02 26 08
29 01 00 00 00 00 02 26 00
29 01 00 00 10 00 02 FF 00
@@ -522,10 +507,32 @@
29 01 00 00 00 00 02 6A 60
29 01 00 00 00 00 02 FF 00
29 01 00 00 78 00 02 29 00];
-
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [05 01 00 00 32 00 02 28 00
+ qcom,mdss-dsi-off-command = [05 01 00 00 32 00 02 28 00
05 01 00 00 78 00 02 10 00];
- qcom,off-cmds-dsi-state = "DSI_HS_MODE";
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-h-sync-pulse = <1>;
+ qcom,mdss-dsi-traffic-mode = <2>;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-te-pin-select = <1>;
+ qcom,mdss-dsi-te-v-sync-rd-ptr-irq-line = <0x2c>;
+ qcom,mdss-dsi-te-dcs-command = <1>;
+ qcom,mdss-dsi-te-check-enable;
+ qcom,mdss-dsi-te-using-te-pin;
+ qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33 22 27 1e 03 04 00];
+ qcom,mdss-dsi-t-clk-post = <0x20>;
+ qcom,mdss-dsi-t-clk-pre = <0x2c>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = <4095>;
+ qcom,mdss-dsi-dma-trigger = <4>;
+ qcom,mdss-dsi-mdp-trigger = <0>;
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
+
};
};
diff --git a/arch/arm/boot/dts/dsi-panel-nt35590-720p-video.dtsi b/arch/arm/boot/dts/dsi-panel-nt35590-720p-video.dtsi
index d742b30..a171a5c 100644
--- a/arch/arm/boot/dts/dsi-panel-nt35590-720p-video.dtsi
+++ b/arch/arm/boot/dts/dsi-panel-nt35590-720p-video.dtsi
@@ -10,48 +10,40 @@
* GNU General Public License for more details.
*/
+/*---------------------------------------------------------------------------
+ * This file is autogenerated file using gcdb parser. Please do not edit it.
+ * Update input XML file to add a new entry or update variable in this file
+ * VERSION = "1.0"
+ *---------------------------------------------------------------------------*/
&soc {
qcom,mdss_dsi_nt35590_720p_video {
compatible = "qcom,mdss-dsi-panel";
- label = "nt35590 720p video mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,rst-gpio = <&msmgpio 25 0>;
- qcom,mdss-pan-res = <720 1280>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <164 8 140 1 1 6>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
- qcom,mdss-pan-bl-levels = <1 4095>;
- qcom,mdss-pan-dsi-mode = <0>;
- qcom,mdss-pan-dsi-h-pulse-mode = <1>;
- qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <2>;
- qcom,mdss-pan-dsi-dst-format = <3>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 1 1>; /* 4 lanes */
- qcom,mdss-pan-dsi-dlane-swap = <0>;
- qcom,mdss-pan-dsi-t-clk = <0x2c 0x20>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x0>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-dsi-frame-rate = <60>;
- qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regualotor settings */
- 20 00 01];
- qcom,panel-phy-timingSettings = [7d 25 1d 00 37 33
- 22 27 1e 03 04 00];
- qcom,panel-phy-strengthCtrl = [ff 06];
- qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
- 00 00];
- qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
- 00 00 00 00 05 00 00 01 97 /* lane1 config */
- 00 00 00 00 0a 00 00 01 97 /* lane2 config */
- 00 00 00 00 0f 00 00 01 97 /* lane3 config */
- 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
- qcom,panel-on-cmds = [29 01 00 00 00 00 02 FF EE
+ qcom,mdss-dsi-panel-name = "nt35590 720p video mode dsi panel";
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-type = "dsi_video_mode";
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-panel-width = <720>;
+ qcom,mdss-dsi-panel-height = <1280>;
+ qcom,mdss-dsi-h-front-porch = <140>;
+ qcom,mdss-dsi-h-back-porch = <164>;
+ qcom,mdss-dsi-h-pulse-width = <8>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <1>;
+ qcom,mdss-dsi-v-front-porch = <6>;
+ qcom,mdss-dsi-v-pulse-width = <1>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-on-command = [29 01 00 00 00 00 02 FF EE
29 01 00 00 00 00 02 26 08
29 01 00 00 00 00 02 26 00
29 01 00 00 10 00 02 FF 00
@@ -516,10 +508,27 @@
29 01 00 00 00 00 02 FF 00
29 01 00 00 78 00 02 29 00
29 01 00 00 78 00 02 53 2C];
-
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [05 01 00 00 32 00 02 28 00
+ qcom,mdss-dsi-off-command = [05 01 00 00 32 00 02 28 00
05 01 00 00 78 00 02 10 00];
- qcom,off-cmds-dsi-state = "DSI_HS_MODE";
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-h-sync-pulse = <1>;
+ qcom,mdss-dsi-traffic-mode = <2>;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33 22 27 1e 03 04 00];
+ qcom,mdss-dsi-t-clk-post = <0x20>;
+ qcom,mdss-dsi-t-clk-pre = <0x2c>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = <4095>;
+ qcom,mdss-dsi-dma-trigger = <4>;
+ qcom,mdss-dsi-mdp-trigger = <0>;
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
+
};
};
diff --git a/arch/arm/boot/dts/dsi-panel-nt35596-1080p-video.dtsi b/arch/arm/boot/dts/dsi-panel-nt35596-1080p-video.dtsi
index 1ecad71..998799a 100644
--- a/arch/arm/boot/dts/dsi-panel-nt35596-1080p-video.dtsi
+++ b/arch/arm/boot/dts/dsi-panel-nt35596-1080p-video.dtsi
@@ -10,48 +10,40 @@
* GNU General Public License for more details.
*/
+/*---------------------------------------------------------------------------
+ * This file is autogenerated file using gcdb parser. Please do not edit it.
+ * Update input XML file to add a new entry or update variable in this file
+ * VERSION = "1.0"
+ *---------------------------------------------------------------------------*/
&soc {
qcom,mdss_dsi_nt35596_1080p_video {
compatible = "qcom,mdss-dsi-panel";
- label = "nt35596 1080p video mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,rst-gpio = <&msmgpio 25 0>;
- qcom,mdss-pan-res = <1080 1920>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <32 8 32 18 2 2>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
- qcom,mdss-pan-bl-levels = <1 4095>;
- qcom,mdss-pan-dsi-mode = <0>;
- qcom,mdss-pan-dsi-h-pulse-mode = <1>;
- qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <2>;
- qcom,mdss-pan-dsi-dst-format = <3>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 1 1>; /* 4 lanes */
- qcom,mdss-pan-dsi-dlane-swap = <0>;
- qcom,mdss-pan-dsi-t-clk = <0x38 0x1e>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x0>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-dsi-frame-rate = <60>;
- qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regualotor settings */
- 20 00 01];
- qcom,panel-phy-timingSettings = [f9 3d 34 00 58 4d
- 36 3f 53 03 04 00];
- qcom,panel-phy-strengthCtrl = [ff 06];
- qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
- 00 00];
- qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
- 00 00 00 00 05 00 00 01 97 /* lane1 config */
- 00 00 00 00 0a 00 00 01 97 /* lane2 config */
- 00 00 00 00 0f 00 00 01 97 /* lane3 config */
- 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
- qcom,panel-on-cmds = [29 01 00 00 00 00 02 FF EE
+ qcom,mdss-dsi-panel-name = "nt35596 1080p video mode dsi panel";
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-type = "dsi_video_mode";
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-panel-width = <1080>;
+ qcom,mdss-dsi-panel-height = <1920>;
+ qcom,mdss-dsi-h-front-porch = <32>;
+ qcom,mdss-dsi-h-back-porch = <32>;
+ qcom,mdss-dsi-h-pulse-width = <8>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <18>;
+ qcom,mdss-dsi-v-front-porch = <2>;
+ qcom,mdss-dsi-v-pulse-width = <2>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-on-command = [29 01 00 00 00 00 02 FF EE
29 01 00 00 00 00 02 FB 01
29 01 00 00 00 00 02 1F 45
29 01 00 00 00 00 02 24 4F
@@ -571,10 +563,27 @@
29 01 00 00 00 00 02 FF 00
29 01 00 00 00 00 02 35 00
29 01 00 00 78 00 02 29 00];
-
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [05 01 00 00 32 00 02 28 00
+ qcom,mdss-dsi-off-command = [05 01 00 00 32 00 02 28 00
05 01 00 00 78 00 02 10 00];
- qcom,off-cmds-dsi-state = "DSI_HS_MODE";
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-h-sync-pulse = <1>;
+ qcom,mdss-dsi-traffic-mode = <2>;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-panel-timings = [f9 3d 34 00 58 4d 36 3f 53 03 04 00];
+ qcom,mdss-dsi-t-clk-post = <0x1e>;
+ qcom,mdss-dsi-t-clk-pre = <0x38>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = <4095>;
+ qcom,mdss-dsi-dma-trigger = <4>;
+ qcom,mdss-dsi-mdp-trigger = <0>;
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
+
};
};
diff --git a/arch/arm/boot/dts/dsi-panel-toshiba-720p-video.dtsi b/arch/arm/boot/dts/dsi-panel-toshiba-720p-video.dtsi
index 5c37cf8..a824d45 100644
--- a/arch/arm/boot/dts/dsi-panel-toshiba-720p-video.dtsi
+++ b/arch/arm/boot/dts/dsi-panel-toshiba-720p-video.dtsi
@@ -10,115 +10,88 @@
* GNU General Public License for more details.
*/
+/*---------------------------------------------------------------------------
+ * This file is autogenerated file using gcdb parser. Please do not edit it.
+ * Update input XML file to add a new entry or update variable in this file
+ * VERSION = "1.0"
+ *---------------------------------------------------------------------------*/
&soc {
-
qcom,mdss_dsi_toshiba_720p_video {
compatible = "qcom,mdss-dsi-panel";
- label = "toshiba 720p video mode dsi panel";
status = "disable";
- qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
- qcom,enable-gpio = <&msmgpio 58 0>;
- qcom,rst-gpio = <&pm8941_gpios 19 0>;
- qcom,mdss-pan-res = <720 1280>;
- qcom,mdss-pan-bpp = <24>;
- qcom,mdss-pan-dest = "display_1";
- qcom,mdss-pan-porch-values = <32 12 144 3 4 9>;
- qcom,mdss-pan-underflow-clr = <0xff>;
- qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
- qcom,mdss-pan-bl-levels = <1 4095>;
- qcom,mdss-pan-dsi-mode = <0>;
- qcom,mdss-pan-dsi-h-pulse-mode = <0>;
- qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
- qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
- qcom,mdss-pan-dsi-traffic-mode = <1>;
- qcom,mdss-pan-dsi-dst-format = <3>;
- qcom,mdss-pan-dsi-vc = <0>;
- qcom,mdss-pan-dsi-rgb-swap = <0>;
- qcom,mdss-pan-dsi-data-lanes = <1 1 1 1>;
- qcom,mdss-pan-dsi-dlane-swap = <0>;
- qcom,mdss-pan-dsi-t-clk = <0x1b 0x04>;
- qcom,mdss-pan-dsi-stream = <0>;
- qcom,mdss-pan-dsi-mdp-tr = <0x0>;
- qcom,mdss-pan-dsi-dma-tr = <0x04>;
- qcom,mdss-pan-dsi-frame-rate = <60>;
- qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regualotor settings */
- 20 00 01];
- qcom,panel-phy-timingSettings = [b0 23 1b 00 94 93
- 1e 25 15 03 04 00];
- qcom,panel-phy-strengthCtrl = [ff 06];
- qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
- 00 00];
- qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
- 00 00 00 00 05 00 00 01 97 /* lane1 config */
- 00 00 00 00 0a 00 00 01 97 /* lane2 config */
- 00 00 00 00 0f 00 00 01 97 /* lane3 config */
- 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
+ qcom,mdss-dsi-panel-name = "toshiba 720p video mode dsi panel";
+ qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
+ qcom,mdss-dsi-panel-type = "dsi_video_mode";
+ qcom,mdss-dsi-panel-destination = "display_1";
+ qcom,mdss-dsi-panel-framerate = <60>;
+ qcom,mdss-dsi-virtual-channel-id = <0>;
+ qcom,mdss-dsi-stream = <0>;
+ qcom,mdss-dsi-panel-width = <720>;
+ qcom,mdss-dsi-panel-height = <1280>;
+ qcom,mdss-dsi-h-front-porch = <144>;
+ qcom,mdss-dsi-h-back-porch = <32>;
+ qcom,mdss-dsi-h-pulse-width = <12>;
+ qcom,mdss-dsi-h-sync-skew = <0>;
+ qcom,mdss-dsi-v-back-porch = <3>;
+ qcom,mdss-dsi-v-front-porch = <9>;
+ qcom,mdss-dsi-v-pulse-width = <4>;
+ qcom,mdss-dsi-h-left-border = <0>;
+ qcom,mdss-dsi-h-right-border = <0>;
+ qcom,mdss-dsi-v-top-border = <0>;
+ qcom,mdss-dsi-v-bottom-border = <0>;
+ qcom,mdss-dsi-bpp = <24>;
+ qcom,mdss-dsi-color-order = <0>;
+ qcom,mdss-dsi-underflow-color = <0xff>;
+ qcom,mdss-dsi-border-color = <0>;
+ qcom,mdss-dsi-on-command = [23 01 00 00 0a 00 02 b0 00
+ 23 01 00 00 0a 00 02 b2 00
+ 23 01 00 00 0a 00 02 b3 0c
+ 23 01 00 00 0a 00 02 b4 02
+ 29 01 00 00 00 00 06 c0 40 02 7f c8 08
+ 29 01 00 00 00 00 10 c1 00 a8 00 00 00 00 00 9d 08 27 00 00 00 00 00
+ 29 01 00 00 00 00 06 c2 00 00 09 00 00
+ 23 01 00 00 0a 00 02 c3 04
+ 29 01 00 00 00 00 04 c4 4d 83 00
+ 29 01 00 00 00 00 0b c6 12 00 08 71 00 00 00 80 00 04
+ 23 01 00 00 0a 00 02 c7 22
+ 29 01 00 00 00 00 05 c8 4c 0c 0c 0c
+ 29 01 00 00 00 00 0e c9 00 40 00 16 32 2e 3a 43 3e 3c 45 79 3f
+ 29 01 00 00 00 00 0e ca 00 46 1a 23 21 1c 25 31 2d 49 5f 7f 3f
+ 29 01 00 00 00 00 0e cb 00 4c 20 3a 42 40 47 4b 42 3e 46 7e 3f
+ 29 01 00 00 00 00 0e cc 00 41 19 21 1d 14 18 1f 1d 25 3f 73 3f
+ 29 01 00 00 00 00 0e cd 23 79 5a 5f 57 4c 51 51 45 3f 4b 7f 3f
+ 29 01 00 00 00 00 0e ce 00 40 14 20 1a 0e 0e 13 08 00 05 46 1c
+ 29 01 00 00 00 00 04 d0 6a 64 01
+ 29 01 00 00 00 00 03 d1 77 d4
+ 23 01 00 00 0a 00 02 d3 33
+ 29 01 00 00 00 00 03 d5 0f 0f
+ 29 01 00 00 00 00 07 d8 34 64 23 25 62 32
+ 29 01 00 00 00 00 0c de 10 7b 11 0a 00 00 00 00 00 00 00
+ 29 01 00 00 00 00 09 fd 04 55 53 00 70 ff 10 73
+ 23 01 00 00 0a 00 02 e2 00
+ 05 01 00 00 78 00 02 11 00
+ 05 01 00 00 32 00 02 29 00];
+ qcom,mdss-dsi-off-command = [05 01 00 00 32 00 02 28 00
+ 05 01 00 00 78 00 02 10 00];
+ qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
+ qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
+ qcom,mdss-dsi-h-sync-pulse = <0>;
+ qcom,mdss-dsi-traffic-mode = <1>;
+ qcom,mdss-dsi-lane-map = <0>;
+ qcom,mdss-dsi-bllp-eof-power-mode;
+ qcom,mdss-dsi-bllp-power-mode;
+ qcom,mdss-dsi-lane-0-state;
+ qcom,mdss-dsi-lane-1-state;
+ qcom,mdss-dsi-lane-2-state;
+ qcom,mdss-dsi-lane-3-state;
+ qcom,mdss-dsi-panel-timings = [b0 23 1b 00 94 93 1e 25 15 03 04 00];
+ qcom,mdss-dsi-t-clk-post = <0x04>;
+ qcom,mdss-dsi-t-clk-pre = <0x1b>;
+ qcom,mdss-dsi-bl-min-level = <1>;
+ qcom,mdss-dsi-bl-max-level = <4095>;
+ qcom,mdss-dsi-dma-trigger = <0x04>;
+ qcom,mdss-dsi-mdp-trigger = <0x0>;
+ qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
- qcom,panel-on-cmds = [23 01 00 00 0a 00 02 b0 00
- 23 01 00 00 0a 00 02 b2 00
- 23 01 00 00 0a 00 02 b3 0c
- 23 01 00 00 0a 00 02 b4 02
- 29 01 00 00 00 00 06
- c0 40 02 7f c8 08
- 29 01 00 00 00 00 10
- c1 00 a8 00 00 00
- 00 00 9d 08 27 00
- 00 00 00 00
- 29 01 00 00 00 00 06
- c2 00 00 09 00 00
- 23 01 00 00 0a 00 02 c3 04
- 29 01 00 00 00 00 04
- c4 4d 83 00
- 29 01 00 00 00 00 0b
- c6 12 00 08 71 00
- 00 00 80 00 04
- 23 01 00 00 0a 00 02 c7 22
- 29 01 00 00 00 00 05
- c8 4c 0c 0c 0c
- 29 01 00 00 00 00 0e
- c9 00 40 00 16 32
- 2e 3a 43 3e 3c 45
- 79 3f
- 29 01 00 00 00 00 0e
- ca 00 46 1a 23 21
- 1c 25 31 2d 49 5f
- 7f 3f
- 29 01 00 00 00 00 0e
- cb 00 4c 20 3a 42
- 40 47 4b 42 3e 46
- 7e 3f
- 29 01 00 00 00 00 0e
- cc 00 41 19 21 1d
- 14 18 1f 1d 25 3f
- 73 3f
- 29 01 00 00 00 00 0e
- cd 23 79 5a 5f 57
- 4c 51 51 45 3f 4b
- 7f 3f
- 29 01 00 00 00 00 0e
- ce 00 40 14 20 1a
- 0e 0e 13 08 00 05
- 46 1c
- 29 01 00 00 00 00 04
- d0 6a 64 01
- 29 01 00 00 00 00 03 d1 77 d4
- 23 01 00 00 0a 00 02 d3 33
- 29 01 00 00 00 00 03 d5 0f 0f
- 29 01 00 00 00 00 07
- d8 34 64 23 25 62
- 32
- 29 01 00 00 00 00 0c
- de 10 7b 11 0a 00
- 00 00 00 00 00 00
- 29 01 00 00 00 00 09
- fd 04 55 53 00 70
- ff 10 73
- 23 01 00 00 0a 00 02 e2 00
- 05 01 00 00 78 00 02 11 00
- 05 01 00 00 32 00 02 29 00];
- qcom,on-cmds-dsi-state = "DSI_LP_MODE";
- qcom,panel-off-cmds = [05 01 00 00 32 00 02 28 00
- 05 01 00 00 78 00 02 10 00];
- qcom,off-cmds-dsi-state = "DSI_HS_MODE";
};
};
diff --git a/arch/arm/boot/dts/msm8226-mdss.dtsi b/arch/arm/boot/dts/msm8226-mdss.dtsi
index b895c64..5f991fb 100644
--- a/arch/arm/boot/dts/msm8226-mdss.dtsi
+++ b/arch/arm/boot/dts/msm8226-mdss.dtsi
@@ -62,14 +62,54 @@
label = "MDSS DSI CTRL->0";
cell-index = <0>;
reg = <0xfd922800 0x600>;
+ qcom,mdss-fb-map = <&mdss_fb0>;
vdd-supply = <&pm8226_l15>;
vddio-supply = <&pm8226_l8>;
vdda-supply = <&pm8226_l4>;
- qcom,supply-names = "vdd", "vddio", "vdda";
- qcom,supply-min-voltage-level = <2800000 1800000 1200000>;
- qcom,supply-max-voltage-level = <2800000 1800000 1200000>;
- qcom,supply-peak-current = <150000 100000 100000>;
- qcom,mdss-fb-map = <&mdss_fb0>;
+ qcom,platform-reset-gpio = <&msmgpio 25 1>;
+ qcom,platform-te-gpio = <&msmgpio 24 0>;
+ qcom,platform-strength-ctrl = [ff 06];
+ qcom,platform-bist-ctrl = [00 00 b1 ff 00 00];
+ qcom,platform-regulator-settings = [07 09 03 00 20 00 01];
+ qcom,platform-lane-config = [00 00 00 00 00 00 00 01 97
+ 00 00 00 00 05 00 00 01 97
+ 00 00 00 00 0a 00 00 01 97
+ 00 00 00 00 0f 00 00 01 97
+ 00 c0 00 00 00 00 00 01 bb];
+ qcom,platform-reset-sequence = <1 20 0 1 1 20>;
+ qcom,platform-supply-entry1 {
+ qcom,supply-name = "vdd";
+ qcom,supply-min-voltage = <2800000>;
+ qcom,supply-max-voltage = <2800000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <0>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
+ qcom,platform-supply-entry2 {
+ qcom,supply-name = "vddio";
+ qcom,supply-min-voltage = <1800000>;
+ qcom,supply-max-voltage = <1800000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <0>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
+ qcom,platform-supply-entry3 {
+ qcom,supply-name = "vdda";
+ qcom,supply-min-voltage = <1200000>;
+ qcom,supply-max-voltage = <1200000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <20>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
};
qcom,mdss_wb_panel {
diff --git a/arch/arm/boot/dts/msm8974-mdss.dtsi b/arch/arm/boot/dts/msm8974-mdss.dtsi
index 46bb71a..52d730d 100644
--- a/arch/arm/boot/dts/msm8974-mdss.dtsi
+++ b/arch/arm/boot/dts/msm8974-mdss.dtsi
@@ -86,6 +86,50 @@
vddio-supply = <&pm8941_l12>;
vdda-supply = <&pm8941_l2>;
qcom,mdss-fb-map = <&mdss_fb0>;
+ qcom,platform-reset-gpio = <&pm8941_gpios 19 1>;
+ qcom,platform-enable-gpio = <&msmgpio 58 1>;
+ qcom,platform-reset-sequence = <1 20 0 200 1 20 2>;
+ qcom,platform-strength-ctrl = [ff 06];
+ qcom,platform-bist-ctrl = [00 00 b1 ff 00 00];
+ qcom,platform-regulator-settings = [07 09 03 00 20 00 01];
+ qcom,platform-lane-config = [00 00 00 00 00 00 00 01 97
+ 00 00 00 00 05 00 00 01 97
+ 00 00 00 00 0a 00 00 01 97
+ 00 00 00 00 0f 00 00 01 97
+ 00 c0 00 00 00 00 00 01 bb];
+ qcom,platform-supply-entry1 {
+ qcom,supply-name = "vdd";
+ qcom,supply-min-voltage = <3000000>;
+ qcom,supply-max-voltage = <3000000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <20>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
+ qcom,platform-supply-entry2 {
+ qcom,supply-name = "vddio";
+ qcom,supply-min-voltage = <1800000>;
+ qcom,supply-max-voltage = <1800000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <20>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
+ qcom,platform-supply-entry3 {
+ qcom,supply-name = "vdda";
+ qcom,supply-min-voltage = <1200000>;
+ qcom,supply-max-voltage = <1200000>;
+ qcom,supply-enable-load = <100000>;
+ qcom,supply-disable-load = <100>;
+ qcom,supply-pre-on-sleep = <0>;
+ qcom,supply-post-on-sleep = <0>;
+ qcom,supply-pre-off-sleep = <0>;
+ qcom,supply-post-off-sleep = <0>;
+ };
};
mdss_dsi1: qcom,mdss_dsi@fd922e00 {
diff --git a/drivers/video/msm/mdss/mdss_dsi.c b/drivers/video/msm/mdss/mdss_dsi.c
index 44a5e62..3b0cd20 100644
--- a/drivers/video/msm/mdss/mdss_dsi.c
+++ b/drivers/video/msm/mdss/mdss_dsi.c
@@ -31,9 +31,7 @@
static int mdss_dsi_regulator_init(struct platform_device *pdev)
{
- int ret = 0;
struct mdss_dsi_ctrl_pdata *ctrl_pdata = NULL;
- struct dsi_drv_cm_data *dsi_drv = NULL;
if (!pdev) {
pr_err("%s: invalid input\n", __func__);
@@ -46,59 +44,9 @@
return -EINVAL;
}
- dsi_drv = &(ctrl_pdata->shared_pdata);
- if (ctrl_pdata->power_data.num_vreg > 0) {
- ret = msm_dss_config_vreg(&pdev->dev,
- ctrl_pdata->power_data.vreg_config,
- ctrl_pdata->power_data.num_vreg, 1);
- } else {
- dsi_drv->vdd_vreg = devm_regulator_get(&pdev->dev, "vdd");
- if (IS_ERR(dsi_drv->vdd_vreg)) {
- pr_err("%s: could not get vdda vreg, rc=%ld\n",
- __func__, PTR_ERR(dsi_drv->vdd_vreg));
- return PTR_ERR(dsi_drv->vdd_vreg);
- }
-
- ret = regulator_set_voltage(dsi_drv->vdd_vreg, 3000000,
- 3000000);
- if (ret) {
- pr_err("%s: set voltage failed on vdda vreg, rc=%d\n",
- __func__, ret);
- return ret;
- }
-
- dsi_drv->vdd_io_vreg = devm_regulator_get(&pdev->dev, "vddio");
- if (IS_ERR(dsi_drv->vdd_io_vreg)) {
- pr_err("%s: could not get vddio reg, rc=%ld\n",
- __func__, PTR_ERR(dsi_drv->vdd_io_vreg));
- return PTR_ERR(dsi_drv->vdd_io_vreg);
- }
-
- ret = regulator_set_voltage(dsi_drv->vdd_io_vreg, 1800000,
- 1800000);
- if (ret) {
- pr_err("%s: set voltage failed on vddio vreg, rc=%d\n",
- __func__, ret);
- return ret;
- }
-
- dsi_drv->vdda_vreg = devm_regulator_get(&pdev->dev, "vdda");
- if (IS_ERR(dsi_drv->vdda_vreg)) {
- pr_err("%s: could not get vdda vreg, rc=%ld\n",
- __func__, PTR_ERR(dsi_drv->vdda_vreg));
- return PTR_ERR(dsi_drv->vdda_vreg);
- }
-
- ret = regulator_set_voltage(dsi_drv->vdda_vreg, 1200000,
- 1200000);
- if (ret) {
- pr_err("%s: set voltage failed on vdda vreg, rc=%d\n",
- __func__, ret);
- return ret;
- }
- }
-
- return 0;
+ return msm_dss_config_vreg(&pdev->dev,
+ ctrl_pdata->power_data.vreg_config,
+ ctrl_pdata->power_data.num_vreg, 1);
}
static int mdss_dsi_panel_power_on(struct mdss_panel_data *pdata, int enable)
@@ -108,7 +56,8 @@
if (pdata == NULL) {
pr_err("%s: Invalid input data\n", __func__);
- return -EINVAL;
+ ret = -EINVAL;
+ goto error;
}
ctrl_pdata = container_of(pdata, struct mdss_dsi_ctrl_pdata,
@@ -116,71 +65,13 @@
pr_debug("%s: enable=%d\n", __func__, enable);
if (enable) {
- if (ctrl_pdata->power_data.num_vreg > 0) {
- ret = msm_dss_enable_vreg(
- ctrl_pdata->power_data.vreg_config,
- ctrl_pdata->power_data.num_vreg, 1);
- if (ret) {
- pr_err("%s:Failed to enable regulators.rc=%d\n",
- __func__, ret);
- return ret;
- }
-
- /*
- * A small delay is needed here after enabling
- * all regulators and before issuing panel reset
- */
- msleep(20);
- } else {
- ret = regulator_set_optimum_mode(
- (ctrl_pdata->shared_pdata).vdd_vreg, 100000);
- if (ret < 0) {
- pr_err("%s: vdd_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_set_optimum_mode(
- (ctrl_pdata->shared_pdata).vdd_io_vreg, 100000);
- if (ret < 0) {
- pr_err("%s: vdd_io_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_set_optimum_mode
- ((ctrl_pdata->shared_pdata).vdda_vreg, 100000);
- if (ret < 0) {
- pr_err("%s: vdda_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_enable(
- (ctrl_pdata->shared_pdata).vdd_io_vreg);
- if (ret) {
- pr_err("%s: Failed to enable regulator.\n",
- __func__);
- return ret;
- }
- msleep(20);
-
- ret = regulator_enable(
- (ctrl_pdata->shared_pdata).vdd_vreg);
- if (ret) {
- pr_err("%s: Failed to enable regulator.\n",
- __func__);
- return ret;
- }
- msleep(20);
-
- ret = regulator_enable(
- (ctrl_pdata->shared_pdata).vdda_vreg);
- if (ret) {
- pr_err("%s: Failed to enable regulator.\n",
- __func__);
- return ret;
- }
+ ret = msm_dss_enable_vreg(
+ ctrl_pdata->power_data.vreg_config,
+ ctrl_pdata->power_data.num_vreg, 1);
+ if (ret) {
+ pr_err("%s:Failed to enable vregs.rc=%d\n",
+ __func__, ret);
+ goto error;
}
if (pdata->panel_info.panel_power_on == 0)
@@ -190,65 +81,16 @@
mdss_dsi_panel_reset(pdata, 0);
- if (ctrl_pdata->power_data.num_vreg > 0) {
- ret = msm_dss_enable_vreg(
- ctrl_pdata->power_data.vreg_config,
- ctrl_pdata->power_data.num_vreg, 0);
- if (ret) {
- pr_err("%s: Failed to disable regs.rc=%d\n",
- __func__, ret);
- return ret;
- }
- } else {
- ret = regulator_disable(
- (ctrl_pdata->shared_pdata).vdd_vreg);
- if (ret) {
- pr_err("%s: Failed to disable regulator.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_disable(
- (ctrl_pdata->shared_pdata).vdda_vreg);
- if (ret) {
- pr_err("%s: Failed to disable regulator.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_disable(
- (ctrl_pdata->shared_pdata).vdd_io_vreg);
- if (ret) {
- pr_err("%s: Failed to disable regulator.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_set_optimum_mode(
- (ctrl_pdata->shared_pdata).vdd_vreg, 100);
- if (ret < 0) {
- pr_err("%s: vdd_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
-
- ret = regulator_set_optimum_mode(
- (ctrl_pdata->shared_pdata).vdd_io_vreg, 100);
- if (ret < 0) {
- pr_err("%s: vdd_io_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
- ret = regulator_set_optimum_mode(
- (ctrl_pdata->shared_pdata).vdda_vreg, 100);
- if (ret < 0) {
- pr_err("%s: vdda_vreg set opt mode failed.\n",
- __func__);
- return ret;
- }
+ ret = msm_dss_enable_vreg(
+ ctrl_pdata->power_data.vreg_config,
+ ctrl_pdata->power_data.num_vreg, 0);
+ if (ret) {
+ pr_err("%s: Failed to disable vregs.rc=%d\n",
+ __func__, ret);
}
}
- return 0;
+error:
+ return ret;
}
static void mdss_dsi_put_dt_vreg_data(struct device *dev,
@@ -269,10 +111,9 @@
static int mdss_dsi_get_dt_vreg_data(struct device *dev,
struct dss_module_power *mp)
{
- int i, rc = 0;
- int dt_vreg_total = 0;
- u32 *val_array = NULL;
- struct device_node *of_node = NULL;
+ int i = 0, rc = 0;
+ u32 tmp = 0;
+ struct device_node *of_node = NULL, *supply_node = NULL;
if (!dev || !mp) {
pr_err("%s: invalid input\n", __func__);
@@ -283,94 +124,131 @@
of_node = dev->of_node;
mp->num_vreg = 0;
- dt_vreg_total = of_property_count_strings(of_node, "qcom,supply-names");
- if (dt_vreg_total < 0) {
- pr_debug("%s: vreg not found. rc=%d\n", __func__,
- dt_vreg_total);
- rc = 0;
- goto error;
- } else {
- pr_debug("%s: vreg found. count=%d\n", __func__, dt_vreg_total);
+ for_each_child_of_node(of_node, supply_node) {
+ if (!strncmp(supply_node->name, "qcom,platform-supply-entry",
+ 26))
+ ++mp->num_vreg;
}
-
- if (dt_vreg_total > 0) {
- mp->num_vreg = dt_vreg_total;
- mp->vreg_config = devm_kzalloc(dev, sizeof(struct dss_vreg) *
- dt_vreg_total, GFP_KERNEL);
- if (!mp->vreg_config) {
- pr_err("%s: can't alloc vreg mem\n", __func__);
- goto error;
- }
- } else {
+ if (mp->num_vreg == 0) {
pr_debug("%s: no vreg\n", __func__);
- return 0;
+ goto novreg;
+ } else {
+ pr_debug("%s: vreg found. count=%d\n", __func__, mp->num_vreg);
}
- val_array = devm_kzalloc(dev, sizeof(u32) * dt_vreg_total, GFP_KERNEL);
- if (!val_array) {
- pr_err("%s: can't allocate vreg scratch mem\n", __func__);
+ mp->vreg_config = devm_kzalloc(dev, sizeof(struct dss_vreg) *
+ mp->num_vreg, GFP_KERNEL);
+ if (!mp->vreg_config) {
+ pr_err("%s: can't alloc vreg mem\n", __func__);
rc = -ENOMEM;
goto error;
}
- for (i = 0; i < dt_vreg_total; i++) {
- const char *st = NULL;
- /* vreg-name */
- rc = of_property_read_string_index(of_node, "qcom,supply-names",
- i, &st);
- if (rc) {
- pr_err("%s: error reading name. i=%d, rc=%d\n",
- __func__, i, rc);
- goto error;
- }
- snprintf(mp->vreg_config[i].vreg_name,
- ARRAY_SIZE((mp->vreg_config[i].vreg_name)), "%s", st);
+ for_each_child_of_node(of_node, supply_node) {
+ if (!strncmp(supply_node->name, "qcom,platform-supply-entry",
+ 26)) {
+ const char *st = NULL;
+ /* vreg-name */
+ rc = of_property_read_string(supply_node,
+ "qcom,supply-name", &st);
+ if (rc) {
+ pr_err("%s: error reading name. rc=%d\n",
+ __func__, rc);
+ goto error;
+ }
+ snprintf(mp->vreg_config[i].vreg_name,
+ ARRAY_SIZE((mp->vreg_config[i].vreg_name)),
+ "%s", st);
+ /* vreg-min-voltage */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-min-voltage", &tmp);
+ if (rc) {
+ pr_err("%s: error reading min volt. rc=%d\n",
+ __func__, rc);
+ goto error;
+ }
+ mp->vreg_config[i].min_voltage = tmp;
- /* vreg-min-voltage */
- memset(val_array, 0, sizeof(u32) * dt_vreg_total);
- rc = of_property_read_u32_array(of_node,
- "qcom,supply-min-voltage-level", val_array,
- dt_vreg_total);
- if (rc) {
- pr_err("%s: error reading min volt. rc=%d\n",
- __func__, rc);
- goto error;
- }
- mp->vreg_config[i].min_voltage = val_array[i];
+ /* vreg-max-voltage */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-max-voltage", &tmp);
+ if (rc) {
+ pr_err("%s: error reading max volt. rc=%d\n",
+ __func__, rc);
+ goto error;
+ }
+ mp->vreg_config[i].max_voltage = tmp;
- /* vreg-max-voltage */
- memset(val_array, 0, sizeof(u32) * dt_vreg_total);
- rc = of_property_read_u32_array(of_node,
- "qcom,supply-max-voltage-level", val_array,
- dt_vreg_total);
- if (rc) {
- pr_err("%s: error reading max volt. rc=%d\n",
- __func__, rc);
- goto error;
- }
- mp->vreg_config[i].max_voltage = val_array[i];
+ /* enable-load */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-enable-load", &tmp);
+ if (rc) {
+ pr_err("%s: error reading enable load. rc=%d\n",
+ __func__, rc);
+ goto error;
+ }
+ mp->vreg_config[i].enable_load = tmp;
- /* vreg-peak-current*/
- memset(val_array, 0, sizeof(u32) * dt_vreg_total);
- rc = of_property_read_u32_array(of_node,
- "qcom,supply-peak-current", val_array,
- dt_vreg_total);
- if (rc) {
- pr_err("%s: error reading peak current. rc=%d\n",
- __func__, rc);
- goto error;
- }
- mp->vreg_config[i].enable_load = val_array[i];
+ /* disable-load */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-disable-load", &tmp);
+ if (rc) {
+ pr_err("%s: error reading disable load. rc=%d\n",
+ __func__, rc);
+ goto error;
+ }
+ mp->vreg_config[i].disable_load = tmp;
- pr_debug("%s: %s min=%d, max=%d, pc=%d\n", __func__,
- mp->vreg_config[i].vreg_name,
- mp->vreg_config[i].min_voltage,
- mp->vreg_config[i].max_voltage,
- mp->vreg_config[i].enable_load);
+ /* pre-sleep */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-pre-on-sleep", &tmp);
+ if (rc) {
+ pr_debug("%s: error reading supply pre sleep value. rc=%d\n",
+ __func__, rc);
+ }
+ mp->vreg_config[i].pre_on_sleep = (!rc ? tmp : 0);
+
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-pre-off-sleep", &tmp);
+ if (rc) {
+ pr_debug("%s: error reading supply pre sleep value. rc=%d\n",
+ __func__, rc);
+ }
+ mp->vreg_config[i].pre_off_sleep = (!rc ? tmp : 0);
+
+ /* post-sleep */
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-post-on-sleep", &tmp);
+ if (rc) {
+ pr_debug("%s: error reading supply post sleep value. rc=%d\n",
+ __func__, rc);
+ }
+ mp->vreg_config[i].post_on_sleep = (!rc ? tmp : 0);
+
+ rc = of_property_read_u32(supply_node,
+ "qcom,supply-post-off-sleep", &tmp);
+ if (rc) {
+ pr_debug("%s: error reading supply post sleep value. rc=%d\n",
+ __func__, rc);
+ }
+ mp->vreg_config[i].post_off_sleep = (!rc ? tmp : 0);
+
+ pr_debug("%s: %s min=%d, max=%d, enable=%d, disable=%d, preonsleep=%d, postonsleep=%d, preoffsleep=%d, postoffsleep=%d\n",
+ __func__,
+ mp->vreg_config[i].vreg_name,
+ mp->vreg_config[i].min_voltage,
+ mp->vreg_config[i].max_voltage,
+ mp->vreg_config[i].enable_load,
+ mp->vreg_config[i].disable_load,
+ mp->vreg_config[i].pre_on_sleep,
+ mp->vreg_config[i].post_on_sleep,
+ mp->vreg_config[i].pre_off_sleep,
+ mp->vreg_config[i].post_off_sleep
+ );
+ ++i;
+ }
}
- devm_kfree(dev, val_array);
-
return rc;
error:
@@ -378,10 +256,9 @@
devm_kfree(dev, mp->vreg_config);
mp->vreg_config = NULL;
}
+novreg:
mp->num_vreg = 0;
- if (val_array)
- devm_kfree(dev, val_array);
return rc;
}
@@ -937,14 +814,14 @@
struct mdss_panel_common_pdata *panel_data)
{
struct mipi_panel_info *mipi;
- int rc;
+ int rc, i, len;
u8 lanes = 0, bpp;
- u32 h_period, v_period, dsi_pclk_rate;
+ u32 h_period, v_period, dsi_pclk_rate, tmp[9];
struct mdss_dsi_ctrl_pdata *ctrl_pdata;
struct device_node *dsi_ctrl_np = NULL;
struct platform_device *ctrl_pdev = NULL;
- bool broadcast;
bool cont_splash_enabled = false;
+ const char *data;
h_period = ((panel_data->panel_info.lcdc.h_pulse_width)
+ (panel_data->panel_info.lcdc.h_back_porch)
@@ -1010,7 +887,7 @@
mipi->dsi_pclk_rate = dsi_pclk_rate;
dsi_ctrl_np = of_parse_phandle(pdev->dev.of_node,
- "qcom,dsi-ctrl-phandle", 0);
+ "qcom,mdss-dsi-panel-controller", 0);
if (!dsi_ctrl_np) {
pr_err("%s: Dsi controller node not initialized\n", __func__);
return -EPROBE_DEFER;
@@ -1031,13 +908,57 @@
return rc;
}
- broadcast = of_property_read_bool(pdev->dev.of_node,
- "qcom,mdss-pan-broadcast-mode");
- if (broadcast)
- ctrl_pdata->shared_pdata.broadcast_enable = 1;
+ data = of_get_property(ctrl_pdev->dev.of_node,
+ "qcom,platform-strength-ctrl", &len);
+ if ((!data) || (len != 2)) {
+ pr_err("%s:%d, Unable to read Phy Strength ctrl settings",
+ __func__, __LINE__);
+ return -EINVAL;
+ }
+ (panel_data->panel_info.mipi.dsi_phy_db)->strength[0] = data[0];
+ (panel_data->panel_info.mipi.dsi_phy_db)->strength[1] = data[1];
- ctrl_pdata->disp_en_gpio = of_get_named_gpio(pdev->dev.of_node,
- "qcom,enable-gpio", 0);
+ data = of_get_property(ctrl_pdev->dev.of_node,
+ "qcom,platform-regulator-settings", &len);
+ if ((!data) || (len != 7)) {
+ pr_err("%s:%d, Unable to read Phy regulator settings",
+ __func__, __LINE__);
+ return -EINVAL;
+ }
+ for (i = 0; i < len; i++) {
+ (panel_data->panel_info.mipi.dsi_phy_db)->regulator[i]
+ = data[i];
+ }
+
+ data = of_get_property(ctrl_pdev->dev.of_node,
+ "qcom,platform-bist-ctrl", &len);
+ if ((!data) || (len != 6)) {
+ pr_err("%s:%d, Unable to read Phy Bist Ctrl settings",
+ __func__, __LINE__);
+ return -EINVAL;
+ }
+ for (i = 0; i < len; i++) {
+ (panel_data->panel_info.mipi.dsi_phy_db)->bistCtrl[i]
+ = data[i];
+ }
+
+ data = of_get_property(ctrl_pdev->dev.of_node,
+ "qcom,platform-lane-config", &len);
+ if ((!data) || (len != 45)) {
+ pr_err("%s:%d, Unable to read Phy lane configure settings",
+ __func__, __LINE__);
+ return -EINVAL;
+ }
+ for (i = 0; i < len; i++) {
+ (panel_data->panel_info.mipi.dsi_phy_db)->laneCfg[i] =
+ data[i];
+ }
+
+ ctrl_pdata->shared_pdata.broadcast_enable = of_property_read_bool(
+ pdev->dev.of_node, "qcom,mdss-dsi-panel-broadcast-mode");
+
+ ctrl_pdata->disp_en_gpio = of_get_named_gpio(ctrl_pdev->dev.of_node,
+ "qcom,platform-enable-gpio", 0);
if (!gpio_is_valid(ctrl_pdata->disp_en_gpio)) {
pr_err("%s:%d, Disp_en gpio not specified\n",
__func__, __LINE__);
@@ -1051,8 +972,8 @@
}
}
- ctrl_pdata->disp_te_gpio = of_get_named_gpio(pdev->dev.of_node,
- "qcom,te-gpio", 0);
+ ctrl_pdata->disp_te_gpio = of_get_named_gpio(ctrl_pdev->dev.of_node,
+ "qcom,platform-te-gpio", 0);
if (!gpio_is_valid(ctrl_pdata->disp_te_gpio)) {
pr_err("%s:%d, Disp_te gpio not specified\n",
__func__, __LINE__);
@@ -1089,9 +1010,17 @@
ctrl_pdata->disp_te_gpio);
}
+ rc = of_property_read_u32_array(ctrl_pdev->dev.of_node,
+ "qcom,platform-reset-sequence", tmp, MDSS_DSI_RST_SEQ_LEN);
+ if (rc)
+ pr_err("%s:%d, unable to read gpio reset sequence\n",
+ __func__, __LINE__);
+ else
+ for (i = 0; i < MDSS_DSI_RST_SEQ_LEN; ++i)
+ ctrl_pdata->rst_seq[i] = tmp[i];
- ctrl_pdata->rst_gpio = of_get_named_gpio(pdev->dev.of_node,
- "qcom,rst-gpio", 0);
+ ctrl_pdata->rst_gpio = of_get_named_gpio(ctrl_pdev->dev.of_node,
+ "qcom,platform-reset-gpio", 0);
if (!gpio_is_valid(ctrl_pdata->rst_gpio)) {
pr_err("%s:%d, reset gpio not specified\n",
__func__, __LINE__);
diff --git a/drivers/video/msm/mdss/mdss_dsi.h b/drivers/video/msm/mdss/mdss_dsi.h
index 8a8e4ca..2603648 100644
--- a/drivers/video/msm/mdss/mdss_dsi.h
+++ b/drivers/video/msm/mdss/mdss_dsi.h
@@ -194,6 +194,8 @@
#define MDSS_DSI_LEN 8 /* 4 x 4 - 6 - 2, bytes dcs header+crc-align */
+#define MDSS_DSI_RST_SEQ_LEN 6
+
struct dsi_buf {
u32 *hdr; /* dsi host header */
char *start; /* buffer start addr */
@@ -346,6 +348,7 @@
u32 pclk_rate;
u32 byte_clk_rate;
struct dss_module_power power_data;
+ int rst_seq[MDSS_DSI_RST_SEQ_LEN];
u32 dsi_irq_mask;
struct mdss_hw *dsi_hw;
diff --git a/drivers/video/msm/mdss/mdss_dsi_panel.c b/drivers/video/msm/mdss/mdss_dsi_panel.c
index 05a84e3..9a019f9 100644
--- a/drivers/video/msm/mdss/mdss_dsi_panel.c
+++ b/drivers/video/msm/mdss/mdss_dsi_panel.c
@@ -158,6 +158,7 @@
void mdss_dsi_panel_reset(struct mdss_panel_data *pdata, int enable)
{
struct mdss_dsi_ctrl_pdata *ctrl_pdata = NULL;
+ int i;
if (pdata == NULL) {
pr_err("%s: Invalid input data\n", __func__);
@@ -181,12 +182,11 @@
pr_debug("%s: enable = %d\n", __func__, enable);
if (enable) {
- gpio_set_value((ctrl_pdata->rst_gpio), 1);
- msleep(20);
- gpio_set_value((ctrl_pdata->rst_gpio), 0);
- udelay(200);
- gpio_set_value((ctrl_pdata->rst_gpio), 1);
- msleep(20);
+ for (i = 0; i < MDSS_DSI_RST_SEQ_LEN; ++i) {
+ gpio_set_value((ctrl_pdata->rst_gpio),
+ ctrl_pdata->rst_seq[i]);
+ msleep(ctrl_pdata->rst_seq[++i]);
+ }
if (gpio_is_valid(ctrl_pdata->disp_en_gpio))
gpio_set_value((ctrl_pdata->disp_en_gpio), 1);
if (ctrl_pdata->ctrl_state & CTRL_STATE_PANEL_INIT) {
@@ -348,11 +348,11 @@
len -= dchdr->dlen;
}
- pcmds->link_state = DSI_LP_MODE; /* default */
-
data = of_get_property(np, link_key, NULL);
- if (!strncmp(data, "DSI_HS_MODE", 11))
+ if (!strncmp(data, "dsi_hs_mode", 11))
pcmds->link_state = DSI_HS_MODE;
+ else
+ pcmds->link_state = DSI_LP_MODE;
pr_debug("%s: dcs_cmd=%x len=%d, cmd_cnt=%d link_state=%d\n", __func__,
pcmds->buf[0], pcmds->blen, pcmds->cmd_cnt, pcmds->link_state);
@@ -361,44 +361,188 @@
}
+static int mdss_panel_dt_get_dst_fmt(u32 bpp, char mipi_mode, u32 pixel_packing,
+ char *dst_format)
+{
+ int rc = 0;
+ switch (bpp) {
+ case 3:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB111;
+ break;
+ case 8:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB332;
+ break;
+ case 12:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB444;
+ break;
+ case 16:
+ switch (mipi_mode) {
+ case DSI_VIDEO_MODE:
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB565;
+ break;
+ case DSI_CMD_MODE:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB565;
+ break;
+ default:
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB565;
+ break;
+ }
+ break;
+ case 18:
+ switch (mipi_mode) {
+ case DSI_VIDEO_MODE:
+ if (pixel_packing == 0)
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB666;
+ else
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB666_LOOSE;
+ break;
+ case DSI_CMD_MODE:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB666;
+ break;
+ default:
+ if (pixel_packing == 0)
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB666;
+ else
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB666_LOOSE;
+ break;
+ }
+ break;
+ case 24:
+ switch (mipi_mode) {
+ case DSI_VIDEO_MODE:
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB888;
+ break;
+ case DSI_CMD_MODE:
+ *dst_format = DSI_CMD_DST_FORMAT_RGB888;
+ break;
+ default:
+ *dst_format = DSI_VIDEO_DST_FORMAT_RGB888;
+ break;
+ }
+ break;
+ default:
+ rc = -EINVAL;
+ break;
+ }
+ return rc;
+}
+
+
+static int mdss_dsi_parse_fbc_params(struct device_node *np,
+ struct mdss_panel_info *panel_info)
+{
+ int rc, fbc_enabled = 0;
+ u32 tmp;
+
+ fbc_enabled = of_property_read_bool(np, "qcom,mdss-dsi-fbc-enable");
+ if (fbc_enabled) {
+ pr_debug("%s:%d FBC panel enabled.\n", __func__, __LINE__);
+ panel_info->fbc.enabled = 1;
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-bpp", &tmp);
+ panel_info->fbc.target_bpp = (!rc ? tmp : panel_info->bpp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-packing",
+ &tmp);
+ panel_info->fbc.comp_mode = (!rc ? tmp : 0);
+ panel_info->fbc.qerr_enable = of_property_read_bool(np,
+ "qcom,mdss-dsi-fbc-quant-error");
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-bias", &tmp);
+ panel_info->fbc.cd_bias = (!rc ? tmp : 0);
+ panel_info->fbc.pat_enable = of_property_read_bool(np,
+ "qcom,mdss-dsi-fbc-pat-mode");
+ panel_info->fbc.vlc_enable = of_property_read_bool(np,
+ "qcom,mdss-dsi-fbc-vlc-mode");
+ panel_info->fbc.bflc_enable = of_property_read_bool(np,
+ "qcom,mdss-dsi-fbc-bflc-mode");
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-h-line-budget",
+ &tmp);
+ panel_info->fbc.line_x_budget = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-budget-ctrl",
+ &tmp);
+ panel_info->fbc.block_x_budget = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-block-budget",
+ &tmp);
+ panel_info->fbc.block_budget = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-fbc-lossless-threshold", &tmp);
+ panel_info->fbc.lossless_mode_thd = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-fbc-lossy-threshold", &tmp);
+ panel_info->fbc.lossy_mode_thd = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-fbc-rgb-threshold",
+ &tmp);
+ panel_info->fbc.lossy_rgb_thd = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-fbc-lossy-mode-idx", &tmp);
+ panel_info->fbc.lossy_mode_idx = (!rc ? tmp : 0);
+ } else {
+ pr_debug("%s:%d Panel does not support FBC.\n",
+ __func__, __LINE__);
+ panel_info->fbc.enabled = 0;
+ panel_info->fbc.target_bpp =
+ panel_info->bpp;
+ }
+ return 0;
+}
+
+
static int mdss_panel_parse_dt(struct platform_device *pdev,
- struct mdss_panel_common_pdata *panel_data)
+ struct mdss_panel_common_pdata *panel_data)
{
struct device_node *np = pdev->dev.of_node;
- u32 res[6], tmp;
- u32 fbc_res[7];
+ u32 tmp;
int rc, i, len;
const char *data;
- static const char *bl_ctrl_type, *pdest;
- bool fbc_enabled = false;
+ static const char *pdest;
- rc = of_property_read_u32_array(np, "qcom,mdss-pan-res", res, 2);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-panel-width", &tmp);
if (rc) {
- pr_err("%s:%d, panel resolution not specified\n",
+ pr_err("%s:%d, panel width not specified\n",
__func__, __LINE__);
return -EINVAL;
}
- panel_data->panel_info.xres = (!rc ? res[0] : 640);
- panel_data->panel_info.yres = (!rc ? res[1] : 480);
+ panel_data->panel_info.xres = (!rc ? tmp : 640);
- rc = of_property_read_u32_array(np, "qcom,mdss-pan-active-res", res, 2);
- if (rc == 0) {
- panel_data->panel_info.lcdc.xres_pad =
- panel_data->panel_info.xres - res[0];
- panel_data->panel_info.lcdc.yres_pad =
- panel_data->panel_info.yres - res[1];
- }
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-bpp", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-panel-height", &tmp);
if (rc) {
- pr_err("%s:%d, panel bpp not specified\n",
+ pr_err("%s:%d, panel height not specified\n",
__func__, __LINE__);
return -EINVAL;
}
+ panel_data->panel_info.yres = (!rc ? tmp : 480);
+
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-left-border", &tmp);
+ panel_data->panel_info.lcdc.xres_pad = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-right-border", &tmp);
+ if (!rc)
+ panel_data->panel_info.lcdc.xres_pad += tmp;
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-v-top-border", &tmp);
+ panel_data->panel_info.lcdc.yres_pad = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-v-bottom-border", &tmp);
+ if (!rc)
+ panel_data->panel_info.lcdc.yres_pad += tmp;
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-bpp", &tmp);
+ if (rc) {
+ pr_err("%s:%d, bpp not specified\n", __func__, __LINE__);
+ return -EINVAL;
+ }
panel_data->panel_info.bpp = (!rc ? tmp : 24);
-
+ panel_data->panel_info.mipi.mode = DSI_VIDEO_MODE;
+ data = of_get_property(np, "qcom,mdss-dsi-panel-type", NULL);
+ if (data && !strncmp(data, "dsi_cmd_mode", 12))
+ panel_data->panel_info.mipi.mode = DSI_CMD_MODE;
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-pixel-packing", &tmp);
+ tmp = (!rc ? tmp : 0);
+ rc = mdss_panel_dt_get_dst_fmt(panel_data->panel_info.bpp,
+ panel_data->panel_info.mipi.mode, tmp,
+ &(panel_data->panel_info.mipi.dst_format));
+ if (rc) {
+ pr_debug("%s: problem determining dst format. Set Default\n",
+ __func__);
+ panel_data->panel_info.mipi.dst_format =
+ DSI_VIDEO_DST_FORMAT_RGB888;
+ }
pdest = of_get_property(pdev->dev.of_node,
- "qcom,mdss-pan-dest", NULL);
+ "qcom,mdss-dsi-panel-destination", NULL);
if (strlen(pdest) != 9) {
pr_err("%s: Unknown pdest specified\n", __func__);
return -EINVAL;
@@ -412,141 +556,132 @@
__func__);
panel_data->panel_info.pdest = DISPLAY_1;
}
-
- rc = of_property_read_u32_array(np,
- "qcom,mdss-pan-porch-values", res, 6);
- panel_data->panel_info.lcdc.h_back_porch = (!rc ? res[0] : 6);
- panel_data->panel_info.lcdc.h_pulse_width = (!rc ? res[1] : 2);
- panel_data->panel_info.lcdc.h_front_porch = (!rc ? res[2] : 6);
- panel_data->panel_info.lcdc.v_back_porch = (!rc ? res[3] : 6);
- panel_data->panel_info.lcdc.v_pulse_width = (!rc ? res[4] : 2);
- panel_data->panel_info.lcdc.v_front_porch = (!rc ? res[5] : 6);
-
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-front-porch", &tmp);
+ panel_data->panel_info.lcdc.h_front_porch = (!rc ? tmp : 6);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-back-porch", &tmp);
+ panel_data->panel_info.lcdc.h_back_porch = (!rc ? tmp : 6);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-pulse-width", &tmp);
+ panel_data->panel_info.lcdc.h_pulse_width = (!rc ? tmp : 2);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-h-sync-skew", &tmp);
+ panel_data->panel_info.lcdc.hsync_skew = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-v-back-porch", &tmp);
+ panel_data->panel_info.lcdc.v_back_porch = (!rc ? tmp : 6);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-v-front-porch", &tmp);
+ panel_data->panel_info.lcdc.v_front_porch = (!rc ? tmp : 6);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-v-pulse-width", &tmp);
+ panel_data->panel_info.lcdc.v_pulse_width = (!rc ? tmp : 2);
rc = of_property_read_u32(np,
- "qcom,mdss-pan-underflow-clr", &tmp);
+ "qcom,mdss-dsi-underflow-color", &tmp);
panel_data->panel_info.lcdc.underflow_clr = (!rc ? tmp : 0xff);
-
- bl_ctrl_type = of_get_property(pdev->dev.of_node,
- "qcom,mdss-pan-bl-ctrl", NULL);
- if ((bl_ctrl_type) && (!strncmp(bl_ctrl_type, "bl_ctrl_wled", 12))) {
- led_trigger_register_simple("bkl-trigger", &bl_led_trigger);
- pr_debug("%s: SUCCESS-> WLED TRIGGER register\n", __func__);
-
- panel_data->panel_info.bklt_ctrl = BL_WLED;
- } else if (!strncmp(bl_ctrl_type, "bl_ctrl_pwm", 11)) {
- panel_data->panel_info.bklt_ctrl = BL_PWM;
-
- rc = of_property_read_u32(np, "qcom,pwm-period", &tmp);
- if (rc) {
- pr_err("%s:%d, Error, panel pwm_period\n",
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-border-color", &tmp);
+ panel_data->panel_info.lcdc.border_clr = (!rc ? tmp : 0);
+ panel_data->panel_info.bklt_ctrl = UNKNOWN_CTRL;
+ data = of_get_property(np, "qcom,mdss-dsi-bl-pmic-control-type", NULL);
+ if (data) {
+ if (!strncmp(data, "bl_ctrl_wled", 12)) {
+ led_trigger_register_simple("bkl-trigger",
+ &bl_led_trigger);
+ pr_debug("%s: SUCCESS-> WLED TRIGGER register\n",
+ __func__);
+ panel_data->panel_info.bklt_ctrl = BL_WLED;
+ } else if (!strncmp(data, "bl_ctrl_pwm", 11)) {
+ panel_data->panel_info.bklt_ctrl = BL_PWM;
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-bl-pmic-pwm-frequency", &tmp);
+ if (rc) {
+ pr_err("%s:%d, Error, panel pwm_period\n",
__func__, __LINE__);
- return -EINVAL;
- }
- panel_data->panel_info.pwm_period = tmp;
-
- rc = of_property_read_u32(np, "qcom,pwm-lpg-channel", &tmp);
- if (rc) {
- pr_err("%s:%d, Error, dsi lpg channel\n",
+ return -EINVAL;
+ }
+ panel_data->panel_info.pwm_period = tmp;
+ rc = of_property_read_u32(np,
+ "qcom,mdss-dsi-bl-pmic-bank-select", &tmp);
+ if (rc) {
+ pr_err("%s:%d, Error, dsi lpg channel\n",
__func__, __LINE__);
- return -EINVAL;
+ return -EINVAL;
+ }
+ panel_data->panel_info.pwm_lpg_chan = tmp;
+ tmp = of_get_named_gpio(np,
+ "qcom,mdss-dsi-pwm-gpio", 0);
+ panel_data->panel_info.pwm_pmic_gpio = tmp;
+ } else if (!strncmp(data, "bl_ctrl_dcs", 11)) {
+ panel_data->panel_info.bklt_ctrl = BL_DCS_CMD;
}
- panel_data->panel_info.pwm_lpg_chan = tmp;
-
- tmp = of_get_named_gpio(np, "qcom,pwm-pmic-gpio", 0);
- panel_data->panel_info.pwm_pmic_gpio = tmp;
- } else if (!strncmp(bl_ctrl_type, "bl_ctrl_dcs", 11)) {
- panel_data->panel_info.bklt_ctrl = BL_DCS_CMD;
- } else {
- pr_debug("%s: Unknown backlight control\n", __func__);
- panel_data->panel_info.bklt_ctrl = UNKNOWN_CTRL;
}
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-bl-min-level", &tmp);
+ panel_data->panel_info.bl_min = (!rc ? tmp : 0);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-bl-max-level", &tmp);
+ panel_data->panel_info.bl_max = (!rc ? tmp : 255);
- rc = of_property_read_u32_array(np,
- "qcom,mdss-pan-bl-levels", res, 2);
- panel_data->panel_info.bl_min = (!rc ? res[0] : 0);
- panel_data->panel_info.bl_max = (!rc ? res[1] : 255);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-interleave-mode", &tmp);
+ panel_data->panel_info.mipi.interleave_mode = (!rc ? tmp : 0);
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-mode", &tmp);
- panel_data->panel_info.mipi.mode = (!rc ? tmp : DSI_VIDEO_MODE);
-
- rc = of_property_read_u32(np, "qcom,mdss-vsync-enable", &tmp);
- panel_data->panel_info.mipi.vsync_enable = (!rc ? tmp : 0);
-
- rc = of_property_read_u32(np, "qcom,mdss-hw-vsync-mode", &tmp);
- panel_data->panel_info.mipi.hw_vsync_mode = (!rc ? tmp : 0);
-
+ panel_data->panel_info.mipi.vsync_enable = of_property_read_bool(np,
+ "qcom,mdss-dsi-te-check-enable");
+ panel_data->panel_info.mipi.hw_vsync_mode = of_property_read_bool(np,
+ "qcom,mdss-dsi-te-using-te-pin");
rc = of_property_read_u32(np,
- "qcom,mdss-pan-dsi-h-pulse-mode", &tmp);
+ "qcom,mdss-dsi-h-sync-pulse", &tmp);
panel_data->panel_info.mipi.pulse_mode_hsa_he = (!rc ? tmp : false);
- rc = of_property_read_u32_array(np,
- "qcom,mdss-pan-dsi-h-power-stop", res, 3);
- panel_data->panel_info.mipi.hbp_power_stop = (!rc ? res[0] : false);
- panel_data->panel_info.mipi.hsa_power_stop = (!rc ? res[1] : false);
- panel_data->panel_info.mipi.hfp_power_stop = (!rc ? res[2] : false);
-
- rc = of_property_read_u32_array(np,
- "qcom,mdss-pan-dsi-bllp-power-stop", res, 2);
- panel_data->panel_info.mipi.bllp_power_stop =
- (!rc ? res[0] : false);
- panel_data->panel_info.mipi.eof_bllp_power_stop =
- (!rc ? res[1] : false);
-
+ panel_data->panel_info.mipi.hfp_power_stop = of_property_read_bool(np,
+ "qcom,mdss-dsi-hfp-power-mode");
+ panel_data->panel_info.mipi.hsa_power_stop = of_property_read_bool(np,
+ "qcom,mdss-dsi-hsa-power-mode");
+ panel_data->panel_info.mipi.hbp_power_stop = of_property_read_bool(np,
+ "qcom,mdss-dsi-hbp-power-mode");
+ panel_data->panel_info.mipi.bllp_power_stop = of_property_read_bool(np,
+ "qcom,mdss-dsi-bllp-power-mode");
+ panel_data->panel_info.mipi.eof_bllp_power_stop = of_property_read_bool(
+ np, "qcom,mdss-dsi-bllp-eof-power-mode");
rc = of_property_read_u32(np,
- "qcom,mdss-pan-dsi-traffic-mode", &tmp);
+ "qcom,mdss-dsi-traffic-mode", &tmp);
panel_data->panel_info.mipi.traffic_mode =
(!rc ? tmp : DSI_NON_BURST_SYNCH_PULSE);
-
rc = of_property_read_u32(np,
- "qcom,mdss-pan-insert-dcs-cmd", &tmp);
+ "qcom,mdss-dsi-te-dcs-command", &tmp);
panel_data->panel_info.mipi.insert_dcs_cmd =
(!rc ? tmp : 1);
-
rc = of_property_read_u32(np,
- "qcom,mdss-pan-wr-mem-continue", &tmp);
+ "qcom,mdss-dsi-te-v-sync-continue-lines", &tmp);
panel_data->panel_info.mipi.wr_mem_continue =
(!rc ? tmp : 0x3c);
-
rc = of_property_read_u32(np,
- "qcom,mdss-pan-wr-mem-start", &tmp);
+ "qcom,mdss-dsi-te-v-sync-rd-ptr-irq-line", &tmp);
panel_data->panel_info.mipi.wr_mem_start =
(!rc ? tmp : 0x2c);
-
rc = of_property_read_u32(np,
- "qcom,mdss-pan-te-sel", &tmp);
+ "qcom,mdss-dsi-te-pin-select", &tmp);
panel_data->panel_info.mipi.te_sel =
(!rc ? tmp : 1);
-
- rc = of_property_read_u32(np,
- "qcom,mdss-pan-dsi-dst-format", &tmp);
- panel_data->panel_info.mipi.dst_format =
- (!rc ? tmp : DSI_VIDEO_DST_FORMAT_RGB888);
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-vc", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-virtual-channel-id", &tmp);
panel_data->panel_info.mipi.vc = (!rc ? tmp : 0);
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-rgb-swap", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-color-order", &tmp);
panel_data->panel_info.mipi.rgb_swap = (!rc ? tmp : DSI_RGB_SWAP_RGB);
+ panel_data->panel_info.mipi.data_lane0 = of_property_read_bool(np,
+ "qcom,mdss-dsi-lane-0-state");
+ panel_data->panel_info.mipi.data_lane1 = of_property_read_bool(np,
+ "qcom,mdss-dsi-lane-1-state");
+ panel_data->panel_info.mipi.data_lane2 = of_property_read_bool(np,
+ "qcom,mdss-dsi-lane-2-state");
+ panel_data->panel_info.mipi.data_lane3 = of_property_read_bool(np,
+ "qcom,mdss-dsi-lane-3-state");
- rc = of_property_read_u32_array(np,
- "qcom,mdss-pan-dsi-data-lanes", res, 4);
- panel_data->panel_info.mipi.data_lane0 = (!rc ? res[0] : true);
- panel_data->panel_info.mipi.data_lane1 = (!rc ? res[1] : false);
- panel_data->panel_info.mipi.data_lane2 = (!rc ? res[2] : false);
- panel_data->panel_info.mipi.data_lane3 = (!rc ? res[3] : false);
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-dlane-swap", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-lane-map", &tmp);
panel_data->panel_info.mipi.dlane_swap = (!rc ? tmp : 0);
- rc = of_property_read_u32_array(np, "qcom,mdss-pan-dsi-t-clk", res, 2);
- panel_data->panel_info.mipi.t_clk_pre = (!rc ? res[0] : 0x24);
- panel_data->panel_info.mipi.t_clk_post = (!rc ? res[1] : 0x03);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-t-clk-pre", &tmp);
+ panel_data->panel_info.mipi.t_clk_pre = (!rc ? tmp : 0x24);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-t-clk-post", &tmp);
+ panel_data->panel_info.mipi.t_clk_post = (!rc ? tmp : 0x03);
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-stream", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-stream", &tmp);
panel_data->panel_info.mipi.stream = (!rc ? tmp : 0);
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-mdp-tr", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-mdp-trigger", &tmp);
panel_data->panel_info.mipi.mdp_trigger =
(!rc ? tmp : DSI_CMD_TRIGGER_SW);
if (panel_data->panel_info.mipi.mdp_trigger > 6) {
@@ -556,7 +691,7 @@
DSI_CMD_TRIGGER_SW;
}
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-dma-tr", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-dma-trigger", &tmp);
panel_data->panel_info.mipi.dma_trigger =
(!rc ? tmp : DSI_CMD_TRIGGER_SW);
if (panel_data->panel_info.mipi.dma_trigger > 6) {
@@ -565,23 +700,11 @@
panel_data->panel_info.mipi.dma_trigger =
DSI_CMD_TRIGGER_SW;
}
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-dsi-frame-rate", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-panel-frame-rate", &tmp);
panel_data->panel_info.mipi.frame_rate = (!rc ? tmp : 60);
-
- rc = of_property_read_u32(np, "qcom,mdss-pan-clk-rate", &tmp);
+ rc = of_property_read_u32(np, "qcom,mdss-dsi-panel-clock-rate", &tmp);
panel_data->panel_info.clk_rate = (!rc ? tmp : 0);
-
- data = of_get_property(np, "qcom,panel-phy-regulatorSettings", &len);
- if ((!data) || (len != 7)) {
- pr_err("%s:%d, Unable to read Phy regulator settings",
- __func__, __LINE__);
- goto error;
- }
- for (i = 0; i < len; i++)
- phy_params.regulator[i] = data[i];
-
- data = of_get_property(np, "qcom,panel-phy-timingSettings", &len);
+ data = of_get_property(np, "qcom,mdss-dsi-panel-timings", &len);
if ((!data) || (len != 12)) {
pr_err("%s:%d, Unable to read Phy timing settings",
__func__, __LINE__);
@@ -590,87 +713,15 @@
for (i = 0; i < len; i++)
phy_params.timing[i] = data[i];
- data = of_get_property(np, "qcom,panel-phy-strengthCtrl", &len);
- if ((!data) || (len != 2)) {
- pr_err("%s:%d, Unable to read Phy Strength ctrl settings",
- __func__, __LINE__);
- goto error;
- }
- phy_params.strength[0] = data[0];
- phy_params.strength[1] = data[1];
-
- data = of_get_property(np, "qcom,panel-phy-bistCtrl", &len);
- if ((!data) || (len != 6)) {
- pr_err("%s:%d, Unable to read Phy Bist Ctrl settings",
- __func__, __LINE__);
- goto error;
- }
- for (i = 0; i < len; i++)
- phy_params.bistCtrl[i] = data[i];
-
- data = of_get_property(np, "qcom,panel-phy-laneConfig", &len);
- if ((!data) || (len != 45)) {
- pr_err("%s:%d, Unable to read Phy lane configure settings",
- __func__, __LINE__);
- goto error;
- }
- for (i = 0; i < len; i++)
- phy_params.laneCfg[i] = data[i];
-
panel_data->panel_info.mipi.dsi_phy_db = &phy_params;
- fbc_enabled = of_property_read_bool(np,
- "qcom,fbc-enabled");
- if (fbc_enabled) {
- pr_debug("%s:%d FBC panel enabled.\n", __func__, __LINE__);
- panel_data->panel_info.fbc.enabled = 1;
-
- rc = of_property_read_u32_array(np,
- "qcom,fbc-mode", fbc_res, 7);
- panel_data->panel_info.fbc.target_bpp =
- (!rc ? fbc_res[0] : panel_data->panel_info.bpp);
- panel_data->panel_info.fbc.comp_mode = (!rc ? fbc_res[1] : 0);
- panel_data->panel_info.fbc.qerr_enable =
- (!rc ? fbc_res[2] : 0);
- panel_data->panel_info.fbc.cd_bias = (!rc ? fbc_res[3] : 0);
- panel_data->panel_info.fbc.pat_enable = (!rc ? fbc_res[4] : 0);
- panel_data->panel_info.fbc.vlc_enable = (!rc ? fbc_res[5] : 0);
- panel_data->panel_info.fbc.bflc_enable =
- (!rc ? fbc_res[6] : 0);
-
- rc = of_property_read_u32_array(np,
- "qcom,fbc-budget-ctl", fbc_res, 3);
- panel_data->panel_info.fbc.line_x_budget =
- (!rc ? fbc_res[0] : 0);
- panel_data->panel_info.fbc.block_x_budget =
- (!rc ? fbc_res[1] : 0);
- panel_data->panel_info.fbc.block_budget =
- (!rc ? fbc_res[2] : 0);
-
- rc = of_property_read_u32_array(np,
- "qcom,fbc-lossy-mode", fbc_res, 4);
- panel_data->panel_info.fbc.lossless_mode_thd =
- (!rc ? fbc_res[0] : 0);
- panel_data->panel_info.fbc.lossy_mode_thd =
- (!rc ? fbc_res[1] : 0);
- panel_data->panel_info.fbc.lossy_rgb_thd =
- (!rc ? fbc_res[2] : 0);
- panel_data->panel_info.fbc.lossy_mode_idx =
- (!rc ? fbc_res[3] : 0);
-
- } else {
- pr_debug("%s:%d Panel does not support FBC.\n",
- __func__, __LINE__);
- panel_data->panel_info.fbc.enabled = 0;
- panel_data->panel_info.fbc.target_bpp =
- panel_data->panel_info.bpp;
- }
+ mdss_dsi_parse_fbc_params(np, &panel_data->panel_info);
mdss_dsi_parse_dcs_cmds(np, &panel_data->on_cmds,
- "qcom,panel-on-cmds", "qcom,on-cmds-dsi-state");
+ "qcom,mdss-dsi-on-command", "qcom,mdss-dsi-on-command-state");
mdss_dsi_parse_dcs_cmds(np, &panel_data->off_cmds,
- "qcom,panel-off-cmds", "qcom,off-cmds-dsi-state");
+ "qcom,mdss-dsi-off-command", "qcom,mdss-dsi-off-command-state");
return 0;
@@ -683,12 +734,12 @@
int rc = 0;
static struct mdss_panel_common_pdata vendor_pdata;
static const char *panel_name;
-
pr_debug("%s:%d, debug info id=%d", __func__, __LINE__, pdev->id);
if (!pdev->dev.of_node)
return -ENODEV;
- panel_name = of_get_property(pdev->dev.of_node, "label", NULL);
+ panel_name = of_get_property(pdev->dev.of_node,
+ "qcom,mdss-dsi-panel-name", NULL);
if (!panel_name)
pr_info("%s:%d, panel name not specified\n",
__func__, __LINE__);