diff --git a/Documentation/cdrom/ide-cd b/Documentation/cdrom/ide-cd
index 2c558cd..f4dc9de 100644
--- a/Documentation/cdrom/ide-cd
+++ b/Documentation/cdrom/ide-cd
@@ -159,42 +159,7 @@
 to change.  If the slot number is -1, the drive is unloaded.
 
 
-4. Compilation options
-----------------------
-
-There are a few additional options which can be set when compiling the
-driver.  Most people should not need to mess with any of these; they
-are listed here simply for completeness.  A compilation option can be
-enabled by adding a line of the form `#define <option> 1' to the top
-of ide-cd.c.  All these options are disabled by default.
-
-VERBOSE_IDE_CD_ERRORS
-  If this is set, ATAPI error codes will be translated into textual
-  descriptions.  In addition, a dump is made of the command which
-  provoked the error.  This is off by default to save the memory used
-  by the (somewhat long) table of error descriptions.  
-
-STANDARD_ATAPI
-  If this is set, the code needed to deal with certain drives which do
-  not properly implement the ATAPI spec will be disabled.  If you know
-  your drive implements ATAPI properly, you can turn this on to get a
-  slightly smaller kernel.
-
-NO_DOOR_LOCKING
-  If this is set, the driver will never attempt to lock the door of
-  the drive.
-
-CDROM_NBLOCKS_BUFFER
-  This sets the size of the buffer to be used for a CDROMREADAUDIO
-  ioctl.  The default is 8.
-
-TEST
-  This currently enables an additional ioctl which enables a user-mode
-  program to execute an arbitrary packet command.  See the source for
-  details.  This should be left off unless you know what you're doing.
-
-
-5. Common problems
+4. Common problems
 ------------------
 
 This section discusses some common problems encountered when trying to
@@ -371,7 +336,7 @@
     expense of low system performance.
 
 
-6. cdchange.c
+5. cdchange.c
 -------------
 
 /*
diff --git a/drivers/ide/aec62xx.c b/drivers/ide/aec62xx.c
index 878f8ec..57d00ca 100644
--- a/drivers/ide/aec62xx.c
+++ b/drivers/ide/aec62xx.c
@@ -81,15 +81,15 @@
 	return chipset_table->ultra_settings;
 }
 
-static void aec6210_set_mode(ide_drive_t *drive, const u8 speed)
+static void aec6210_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	struct ide_host *host	= pci_get_drvdata(dev);
 	struct chipset_bus_clock_list_entry *bus_clock = host->host_priv;
 	u16 d_conf		= 0;
 	u8 ultra = 0, ultra_conf = 0;
 	u8 tmp0 = 0, tmp1 = 0, tmp2 = 0;
+	const u8 speed = drive->dma_mode;
 	unsigned long flags;
 
 	local_irq_save(flags);
@@ -109,15 +109,15 @@
 	local_irq_restore(flags);
 }
 
-static void aec6260_set_mode(ide_drive_t *drive, const u8 speed)
+static void aec6260_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	struct ide_host *host	= pci_get_drvdata(dev);
 	struct chipset_bus_clock_list_entry *bus_clock = host->host_priv;
 	u8 unit			= drive->dn & 1;
 	u8 tmp1 = 0, tmp2 = 0;
 	u8 ultra = 0, drive_conf = 0, ultra_conf = 0;
+	const u8 speed = drive->dma_mode;
 	unsigned long flags;
 
 	local_irq_save(flags);
@@ -134,9 +134,10 @@
 	local_irq_restore(flags);
 }
 
-static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void aec_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	drive->hwif->port_ops->set_dma_mode(drive, pio + XFER_PIO_0);
+	drive->dma_mode = drive->pio_mode;
+	hwif->port_ops->set_dma_mode(hwif, drive);
 }
 
 static int init_chipset_aec62xx(struct pci_dev *dev)
diff --git a/drivers/ide/ali14xx.c b/drivers/ide/ali14xx.c
index 90da1f9..25b9fe3 100644
--- a/drivers/ide/ali14xx.c
+++ b/drivers/ide/ali14xx.c
@@ -109,13 +109,14 @@
  * This function computes timing parameters
  * and sets controller registers accordingly.
  */
-static void ali14xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void ali14xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	int driveNum;
 	int time1, time2;
 	u8 param1, param2, param3, param4;
 	unsigned long flags;
 	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 
 	/* calculate timing, according to PIO mode */
diff --git a/drivers/ide/alim15x3.c b/drivers/ide/alim15x3.c
index 0abc43f..2c8016a 100644
--- a/drivers/ide/alim15x3.c
+++ b/drivers/ide/alim15x3.c
@@ -8,7 +8,7 @@
  *  Copyright (C) 2002 Alan Cox
  *  ALi (now ULi M5228) support by Clear Zhang <Clear.Zhang@ali.com.tw>
  *  Copyright (C) 2007 MontaVista Software, Inc. <source@mvista.com>
- *  Copyright (C) 2007 Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
+ *  Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
  *
  *  (U)DMA capable version of ali 1533/1543(C), 1535(D)
  *
@@ -48,61 +48,84 @@
 static u8 chip_is_1543c_e;
 static struct pci_dev *isa_dev;
 
+static void ali_fifo_control(ide_hwif_t *hwif, ide_drive_t *drive, int on)
+{
+	struct pci_dev *pdev = to_pci_dev(hwif->dev);
+	int pio_fifo = 0x54 + hwif->channel;
+	u8 fifo;
+	int shift = 4 * (drive->dn & 1);
+
+	pci_read_config_byte(pdev, pio_fifo, &fifo);
+	fifo &= ~(0x0F << shift);
+	fifo |= (on << shift);
+	pci_write_config_byte(pdev, pio_fifo, fifo);
+}
+
+static void ali_program_timings(ide_hwif_t *hwif, ide_drive_t *drive,
+				struct ide_timing *t, u8 ultra)
+{
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	int port = hwif->channel ? 0x5c : 0x58;
+	int udmat = 0x56 + hwif->channel;
+	u8 unit = drive->dn & 1, udma;
+	int shift = 4 * unit;
+
+	/* Set up the UDMA */
+	pci_read_config_byte(dev, udmat, &udma);
+	udma &= ~(0x0F << shift);
+	udma |= ultra << shift;
+	pci_write_config_byte(dev, udmat, udma);
+
+	if (t == NULL)
+		return;
+
+	t->setup = clamp_val(t->setup, 1, 8) & 7;
+	t->act8b = clamp_val(t->act8b, 1, 8) & 7;
+	t->rec8b = clamp_val(t->rec8b, 1, 16) & 15;
+	t->active = clamp_val(t->active, 1, 8) & 7;
+	t->recover = clamp_val(t->recover, 1, 16) & 15;
+
+	pci_write_config_byte(dev, port, t->setup);
+	pci_write_config_byte(dev, port + 1, (t->act8b << 4) | t->rec8b);
+	pci_write_config_byte(dev, port + unit + 2,
+			      (t->active << 4) | t->recover);
+}
+
 /**
  *	ali_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Program the controller for the given PIO mode.
  */
 
-static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void ali_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
-	struct pci_dev *dev = to_pci_dev(hwif->dev);
-	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
-	int s_time = t->setup, a_time = t->active, c_time = t->cycle;
-	u8 s_clc, a_clc, r_clc;
-	unsigned long flags;
+	ide_drive_t *pair = ide_get_pair_dev(drive);
 	int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
-	int port = hwif->channel ? 0x5c : 0x58;
-	int portFIFO = hwif->channel ? 0x55 : 0x54;
-	u8 cd_dma_fifo = 0, unit = drive->dn & 1;
+	unsigned long T =  1000000 / bus_speed; /* PCI clock based */
+	struct ide_timing t;
 
-	if ((s_clc = (s_time * bus_speed + 999) / 1000) >= 8)
-		s_clc = 0;
-	if ((a_clc = (a_time * bus_speed + 999) / 1000) >= 8)
-		a_clc = 0;
+	ide_timing_compute(drive, drive->pio_mode, &t, T, 1);
+	if (pair) {
+		struct ide_timing p;
 
-	if (!(r_clc = (c_time * bus_speed + 999) / 1000 - a_clc - s_clc)) {
-		r_clc = 1;
-	} else {
-		if (r_clc >= 16)
-			r_clc = 0;
+		ide_timing_compute(pair, pair->pio_mode, &p, T, 1);
+		ide_timing_merge(&p, &t, &t,
+			IDE_TIMING_SETUP | IDE_TIMING_8BIT);
+		if (pair->dma_mode) {
+			ide_timing_compute(pair, pair->dma_mode, &p, T, 1);
+			ide_timing_merge(&p, &t, &t,
+				IDE_TIMING_SETUP | IDE_TIMING_8BIT);
+		}
 	}
-	local_irq_save(flags);
-	
+
 	/* 
 	 * PIO mode => ATA FIFO on, ATAPI FIFO off
 	 */
-	pci_read_config_byte(dev, portFIFO, &cd_dma_fifo);
-	if (drive->media==ide_disk) {
-		if (unit) {
-			pci_write_config_byte(dev, portFIFO, (cd_dma_fifo & 0x0F) | 0x50);
-		} else {
-			pci_write_config_byte(dev, portFIFO, (cd_dma_fifo & 0xF0) | 0x05);
-		}
-	} else {
-		if (unit) {
-			pci_write_config_byte(dev, portFIFO, cd_dma_fifo & 0x0F);
-		} else {
-			pci_write_config_byte(dev, portFIFO, cd_dma_fifo & 0xF0);
-		}
-	}
-	
-	pci_write_config_byte(dev, port, s_clc);
-	pci_write_config_byte(dev, port + unit + 2, (a_clc << 4) | r_clc);
-	local_irq_restore(flags);
+	ali_fifo_control(hwif, drive, (drive->media == ide_disk) ? 0x05 : 0x00);
+
+	ali_program_timings(hwif, drive, &t, 0);
 }
 
 /**
@@ -132,44 +155,42 @@
 
 /**
  *	ali_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Configure the hardware for the desired IDE transfer mode.
  */
 
-static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void ali_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
+	static u8 udma_timing[7] = { 0xC, 0xB, 0xA, 0x9, 0x8, 0xF, 0xD };
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	u8 speed1		= speed;
-	u8 unit			= drive->dn & 1;
+	ide_drive_t *pair	= ide_get_pair_dev(drive);
+	int bus_speed		= ide_pci_clk ? ide_pci_clk : 33;
+	unsigned long T		=  1000000 / bus_speed; /* PCI clock based */
+	const u8 speed		= drive->dma_mode;
 	u8 tmpbyte		= 0x00;
-	int m5229_udma		= (hwif->channel) ? 0x57 : 0x56;
-
-	if (speed == XFER_UDMA_6)
-		speed1 = 0x47;
+	struct ide_timing t;
 
 	if (speed < XFER_UDMA_0) {
-		u8 ultra_enable	= (unit) ? 0x7f : 0xf7;
-		/*
-		 * clear "ultra enable" bit
-		 */
-		pci_read_config_byte(dev, m5229_udma, &tmpbyte);
-		tmpbyte &= ultra_enable;
-		pci_write_config_byte(dev, m5229_udma, tmpbyte);
+		ide_timing_compute(drive, drive->dma_mode, &t, T, 1);
+		if (pair) {
+			struct ide_timing p;
 
-		/*
-		 * FIXME: Oh, my... DMA timings are never set.
-		 */
+			ide_timing_compute(pair, pair->pio_mode, &p, T, 1);
+			ide_timing_merge(&p, &t, &t,
+				IDE_TIMING_SETUP | IDE_TIMING_8BIT);
+			if (pair->dma_mode) {
+				ide_timing_compute(pair, pair->dma_mode,
+						&p, T, 1);
+				ide_timing_merge(&p, &t, &t,
+					IDE_TIMING_SETUP | IDE_TIMING_8BIT);
+			}
+		}
+		ali_program_timings(hwif, drive, &t, 0);
 	} else {
-		pci_read_config_byte(dev, m5229_udma, &tmpbyte);
-		tmpbyte &= (0x0f << ((1-unit) << 2));
-		/*
-		 * enable ultra dma and set timing
-		 */
-		tmpbyte |= ((0x08 | ((4-speed1)&0x07)) << (unit << 2));
-		pci_write_config_byte(dev, m5229_udma, tmpbyte);
+		ali_program_timings(hwif, drive, NULL,
+				udma_timing[speed - XFER_UDMA_0]);
 		if (speed >= XFER_UDMA_3) {
 			pci_read_config_byte(dev, 0x4b, &tmpbyte);
 			tmpbyte |= 1;
@@ -355,19 +376,13 @@
  *
  *	This checks if the controller and the cable are capable
  *	of UDMA66 transfers. It doesn't check the drives.
- *	But see note 2 below!
- *
- *	FIXME: frobs bits that are not defined on newer ALi devicea
  */
 
 static u8 ali_cable_detect(ide_hwif_t *hwif)
 {
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
-	unsigned long flags;
 	u8 cbl = ATA_CBL_PATA40, tmpbyte;
 
-	local_irq_save(flags);
-
 	if (m5229_revision >= 0xC2) {
 		/*
 		 * m5229 80-pin cable detection (from Host View)
@@ -387,8 +402,6 @@
 		}
 	}
 
-	local_irq_restore(flags);
-
 	return cbl;
 }
 
@@ -584,6 +597,6 @@
 module_init(ali15x3_ide_init);
 module_exit(ali15x3_ide_exit);
 
-MODULE_AUTHOR("Michael Aubry, Andrzej Krzysztofowicz, CJ, Andre Hedrick, Alan Cox");
+MODULE_AUTHOR("Michael Aubry, Andrzej Krzysztofowicz, CJ, Andre Hedrick, Alan Cox, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("PCI driver module for ALi 15x3 IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/amd74xx.c b/drivers/ide/amd74xx.c
index 628cd2e..3747b25 100644
--- a/drivers/ide/amd74xx.c
+++ b/drivers/ide/amd74xx.c
@@ -3,7 +3,7 @@
  * IDE driver for Linux.
  *
  * Copyright (c) 2000-2002 Vojtech Pavlik
- * Copyright (c) 2007-2008 Bartlomiej Zolnierkiewicz
+ * Copyright (c) 2007-2010 Bartlomiej Zolnierkiewicz
  *
  * Based on the work of:
  *      Andre Hedrick
@@ -70,7 +70,8 @@
 	default: return;
 	}
 
-	pci_write_config_byte(dev, AMD_UDMA_TIMING + offset + (3 - dn), t);
+	if (timing->udma)
+		pci_write_config_byte(dev, AMD_UDMA_TIMING + offset + 3 - dn, t);
 }
 
 /*
@@ -78,14 +79,14 @@
  * to a desired transfer mode.  It also can be called by upper layers.
  */
 
-static void amd_set_drive(ide_drive_t *drive, const u8 speed)
+static void amd_set_drive(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	ide_drive_t *peer = ide_get_pair_dev(drive);
 	struct ide_timing t, p;
 	int T, UT;
 	u8 udma_mask = hwif->ultra_mask;
+	const u8 speed = drive->dma_mode;
 
 	T = 1000000000 / amd_clock;
 	UT = (udma_mask == ATA_UDMA2) ? T : (T / 2);
@@ -93,7 +94,7 @@
 	ide_timing_compute(drive, speed, &t, T, UT);
 
 	if (peer) {
-		ide_timing_compute(peer, peer->current_speed, &p, T, UT);
+		ide_timing_compute(peer, peer->pio_mode, &p, T, UT);
 		ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT);
 	}
 
@@ -107,9 +108,10 @@
  * amd_set_pio_mode() is a callback from upper layers for PIO-only tuning.
  */
 
-static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void amd_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	amd_set_drive(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	amd_set_drive(hwif, drive);
 }
 
 static void amd7409_cable_detect(struct pci_dev *dev)
@@ -340,6 +342,6 @@
 module_init(amd74xx_ide_init);
 module_exit(amd74xx_ide_exit);
 
-MODULE_AUTHOR("Vojtech Pavlik");
+MODULE_AUTHOR("Vojtech Pavlik, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("AMD PCI IDE driver");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c
index 248219a..000a78e 100644
--- a/drivers/ide/at91_ide.c
+++ b/drivers/ide/at91_ide.c
@@ -172,11 +172,12 @@
 	leave_16bit(chipselect, mode);
 }
 
-static void at91_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void at91_ide_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	struct ide_timing *timing;
-	u8 chipselect = drive->hwif->select_data;
+	u8 chipselect = hwif->select_data;
 	int use_iordy = 0;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	pdbg("chipselect %u pio %u\n", chipselect, pio);
 
diff --git a/drivers/ide/atiixp.c b/drivers/ide/atiixp.c
index 837322b..15f0ead 100644
--- a/drivers/ide/atiixp.c
+++ b/drivers/ide/atiixp.c
@@ -42,19 +42,20 @@
 
 /**
  *	atiixp_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Set the interface PIO mode.
  */
 
-static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void atiixp_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	unsigned long flags;
 	int timing_shift = (drive->dn ^ 1) * 8;
 	u32 pio_timing_data;
 	u16 pio_mode_data;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	spin_lock_irqsave(&atiixp_lock, flags);
 
@@ -74,21 +75,22 @@
 
 /**
  *	atiixp_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Set a ATIIXP host controller to the desired DMA mode.  This involves
  *	programming the right timing data into the PCI configuration space.
  */
 
-static void atiixp_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void atiixp_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	unsigned long flags;
 	int timing_shift = (drive->dn ^ 1) * 8;
 	u32 tmp32;
 	u16 tmp16;
 	u16 udma_ctl = 0;
+	const u8 speed = drive->dma_mode;
 
 	spin_lock_irqsave(&atiixp_lock, flags);
 
diff --git a/drivers/ide/au1xxx-ide.c b/drivers/ide/au1xxx-ide.c
index 349a67b..b26c234 100644
--- a/drivers/ide/au1xxx-ide.c
+++ b/drivers/ide/au1xxx-ide.c
@@ -99,12 +99,11 @@
 }
 #endif
 
-static void au1xxx_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void au1xxx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
 
-	/* set pio mode! */
-	switch(pio) {
+	switch (drive->pio_mode - XFER_PIO_0) {
 	case 0:
 		mem_sttime = SBC_IDE_TIMING(PIO0);
 
@@ -161,11 +160,11 @@
 	au_writel(mem_stcfg,MEM_STCFG2);
 }
 
-static void auide_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void auide_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
 
-	switch(speed) {
+	switch (drive->dma_mode) {
 #ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 	case XFER_MW_DMA_2:
 		mem_sttime = SBC_IDE_TIMING(MDMA2);
@@ -297,8 +296,8 @@
 	 */
 	drive->waiting_for_dma++;
 	if (drive->waiting_for_dma >= DMA_WAIT_TIMEOUT) {
-		printk(KERN_WARNING "%s: timeout waiting for ddma to \
-                                     complete\n", drive->name);
+		printk(KERN_WARNING "%s: timeout waiting for ddma to complete\n",
+		       drive->name);
 		return 1;
 	}
 	udelay(10);
diff --git a/drivers/ide/cmd640.c b/drivers/ide/cmd640.c
index 1a32d62..d2b8b27 100644
--- a/drivers/ide/cmd640.c
+++ b/drivers/ide/cmd640.c
@@ -572,9 +572,10 @@
 	program_drive_counts(drive, index);
 }
 
-static void cmd640_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cmd640_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned int index = 0, cycle_time;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	u8 b;
 
 	switch (pio) {
@@ -605,7 +606,7 @@
 }
 #endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
 
-static void cmd640_init_dev(ide_drive_t *drive)
+static void __init cmd640_init_dev(ide_drive_t *drive)
 {
 	unsigned int i = drive->hwif->channel * 2 + (drive->dn & 1);
 
diff --git a/drivers/ide/cmd64x.c b/drivers/ide/cmd64x.c
index f2500c8..5f80312 100644
--- a/drivers/ide/cmd64x.c
+++ b/drivers/ide/cmd64x.c
@@ -7,6 +7,7 @@
  * Copyright (C) 1998		David S. Miller (davem@redhat.com)
  *
  * Copyright (C) 1999-2002	Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2007-2010	Bartlomiej Zolnierkiewicz
  * Copyright (C) 2007,2009	MontaVista Software, Inc. <source@mvista.com>
  */
 
@@ -50,72 +51,42 @@
 #define UDIDETCR1	0x7B
 #define DTPR1		0x7C
 
-static u8 quantize_timing(int timing, int quant)
+static void cmd64x_program_timings(ide_drive_t *drive, u8 mode)
 {
-	return (timing + quant - 1) / quant;
-}
-
-/*
- * This routine calculates active/recovery counts and then writes them into
- * the chipset registers.
- */
-static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_time)
-{
+	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-	int clock_time = 1000 / (ide_pci_clk ? ide_pci_clk : 33);
-	u8  cycle_count, active_count, recovery_count, drwtim;
+	int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
+	const unsigned long T = 1000000 / bus_speed;
 	static const u8 recovery_values[] =
 		{15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
+	static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
+	static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
 	static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
+	struct ide_timing t;
+	u8 arttim = 0;
 
-	cycle_count	= quantize_timing( cycle_time, clock_time);
-	active_count	= quantize_timing(active_time, clock_time);
-	recovery_count	= cycle_count - active_count;
+	ide_timing_compute(drive, mode, &t, T, 0);
 
 	/*
 	 * In case we've got too long recovery phase, try to lengthen
 	 * the active phase
 	 */
-	if (recovery_count > 16) {
-		active_count += recovery_count - 16;
-		recovery_count = 16;
+	if (t.recover > 16) {
+		t.active += t.recover - 16;
+		t.recover = 16;
 	}
-	if (active_count > 16)		/* shouldn't actually happen... */
-	 	active_count = 16;
+	if (t.active > 16)		/* shouldn't actually happen... */
+		t.active = 16;
 
 	/*
 	 * Convert values to internal chipset representation
 	 */
-	recovery_count = recovery_values[recovery_count];
- 	active_count  &= 0x0f;
+	t.recover = recovery_values[t.recover];
+	t.active &= 0x0f;
 
 	/* Program the active/recovery counts into the DRWTIM register */
-	drwtim = (active_count << 4) | recovery_count;
-	(void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
-}
-
-/*
- * This routine writes into the chipset registers
- * PIO setup/active/recovery timings.
- */
-static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
-{
-	ide_hwif_t *hwif	= drive->hwif;
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	struct ide_timing *t	= ide_timing_find_mode(XFER_PIO_0 + pio);
-	unsigned long setup_count;
-	unsigned int cycle_time;
-	u8 arttim = 0;
-
-	static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
-	static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
-
-	cycle_time = ide_pio_cycle_time(drive, pio);
-
-	program_cycle_times(drive, cycle_time, t->active);
-
-	setup_count = quantize_timing(t->setup,
-			1000 / (ide_pci_clk ? ide_pci_clk : 33));
+	pci_write_config_byte(dev, drwtim_regs[drive->dn],
+			      (t.active << 4) | t.recover);
 
 	/*
 	 * The primary channel has individual address setup timing registers
@@ -126,15 +97,21 @@
 	if (hwif->channel) {
 		ide_drive_t *pair = ide_get_pair_dev(drive);
 
-		ide_set_drivedata(drive, (void *)setup_count);
+		if (pair) {
+			struct ide_timing tp;
 
-		if (pair)
-			setup_count = max_t(u8, setup_count,
-					(unsigned long)ide_get_drivedata(pair));
+			ide_timing_compute(pair, pair->pio_mode, &tp, T, 0);
+			ide_timing_merge(&t, &tp, &t, IDE_TIMING_SETUP);
+			if (pair->dma_mode) {
+				ide_timing_compute(pair, pair->dma_mode,
+						&tp, T, 0);
+				ide_timing_merge(&tp, &t, &t, IDE_TIMING_SETUP);
+			}
+		}
 	}
 
-	if (setup_count > 5)		/* shouldn't actually happen... */
-		setup_count = 5;
+	if (t.setup > 5)		/* shouldn't actually happen... */
+		t.setup = 5;
 
 	/*
 	 * Program the address setup clocks into the ARTTIM registers.
@@ -144,7 +121,7 @@
 	if (hwif->channel)
 		arttim &= ~ARTTIM23_INTR_CH1;
 	arttim &= ~0xc0;
-	arttim |= setup_values[setup_count];
+	arttim |= setup_values[t.setup];
 	(void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
 }
 
@@ -153,8 +130,10 @@
  * Special cases are 8: prefetch off, 9: prefetch on (both never worked)
  */
 
-static void cmd64x_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cmd64x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
+
 	/*
 	 * Filter out the prefetch control values
 	 * to prevent PIO5 from being programmed
@@ -162,20 +141,18 @@
 	if (pio == 8 || pio == 9)
 		return;
 
-	cmd64x_tune_pio(drive, pio);
+	cmd64x_program_timings(drive, XFER_PIO_0 + pio);
 }
 
-static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void cmd64x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 unit			= drive->dn & 0x01;
 	u8 regU = 0, pciU	= hwif->channel ? UDIDETCR1 : UDIDETCR0;
+	const u8 speed		= drive->dma_mode;
 
-	if (speed >= XFER_SW_DMA_0) {
-		(void) pci_read_config_byte(dev, pciU, &regU);
-		regU &= ~(unit ? 0xCA : 0x35);
-	}
+	pci_read_config_byte(dev, pciU, &regU);
+	regU &= ~(unit ? 0xCA : 0x35);
 
 	switch(speed) {
 	case XFER_UDMA_5:
@@ -197,18 +174,13 @@
 		regU |= unit ? 0xC2 : 0x31;
 		break;
 	case XFER_MW_DMA_2:
-		program_cycle_times(drive, 120, 70);
-		break;
 	case XFER_MW_DMA_1:
-		program_cycle_times(drive, 150, 80);
-		break;
 	case XFER_MW_DMA_0:
-		program_cycle_times(drive, 480, 215);
+		cmd64x_program_timings(drive, speed);
 		break;
 	}
 
-	if (speed >= XFER_SW_DMA_0)
-		(void) pci_write_config_byte(dev, pciU, regU);
+	pci_write_config_byte(dev, pciU, regU);
 }
 
 static void cmd648_clear_irq(ide_drive_t *drive)
@@ -471,6 +443,6 @@
 module_init(cmd64x_ide_init);
 module_exit(cmd64x_ide_exit);
 
-MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick");
+MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("PCI driver module for CMD64x IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/cs5520.c b/drivers/ide/cs5520.c
index 09f98ed..2c1e5f7 100644
--- a/drivers/ide/cs5520.c
+++ b/drivers/ide/cs5520.c
@@ -57,11 +57,11 @@
 	{1, 2, 1}
 };
 
-static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cs5520_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *pdev = to_pci_dev(hwif->dev);
 	int controller = drive->dn > 1 ? 1 : 0;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	/* 8bit CAT/CRT - 8bit command timing for channel */
 	pci_write_config_byte(pdev, 0x62 + controller, 
@@ -81,11 +81,12 @@
 		(cs5520_pio_clocks[pio].assert));
 }
 
-static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void cs5520_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	printk(KERN_ERR "cs55x0: bad ide timing.\n");
 
-	cs5520_set_pio_mode(drive, 0);
+	drive->pio_mode = XFER_PIO_0 + 0;
+	cs5520_set_pio_mode(hwif, drive);
 }
 
 static const struct ide_port_ops cs5520_port_ops = {
diff --git a/drivers/ide/cs5530.c b/drivers/ide/cs5530.c
index 40bf05e..4dc4eb9 100644
--- a/drivers/ide/cs5530.c
+++ b/drivers/ide/cs5530.c
@@ -41,8 +41,8 @@
 
 /**
  *	cs5530_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Handles setting of PIO mode for the chipset.
  *
@@ -50,10 +50,11 @@
  *	will have valid default PIO timings set up before we get here.
  */
 
-static void cs5530_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cs5530_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	unsigned long basereg = CS5530_BASEREG(drive->hwif);
+	unsigned long basereg = CS5530_BASEREG(hwif);
 	unsigned int format = (inl(basereg + 4) >> 31) & 1;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
 }
@@ -99,12 +100,12 @@
 	return mask;
 }
 
-static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void cs5530_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned long basereg;
 	unsigned int reg, timings = 0;
 
-	switch (mode) {
+	switch (drive->dma_mode) {
 		case XFER_UDMA_0:	timings = 0x00921250; break;
 		case XFER_UDMA_1:	timings = 0x00911140; break;
 		case XFER_UDMA_2:	timings = 0x00911030; break;
@@ -112,7 +113,7 @@
 		case XFER_MW_DMA_1:	timings = 0x00012121; break;
 		case XFER_MW_DMA_2:	timings = 0x00002020; break;
 	}
-	basereg = CS5530_BASEREG(drive->hwif);
+	basereg = CS5530_BASEREG(hwif);
 	reg = inl(basereg + 4);			/* get drive0 config register */
 	timings |= reg & 0x80000000;		/* preserve PIO format bit */
 	if ((drive-> dn & 1) == 0) {		/* are we configuring drive0? */
diff --git a/drivers/ide/cs5535.c b/drivers/ide/cs5535.c
index b883838..5059faf 100644
--- a/drivers/ide/cs5535.c
+++ b/drivers/ide/cs5535.c
@@ -86,7 +86,7 @@
 		cmd = pioa = speed - XFER_PIO_0;
 
 		if (pair) {
-			u8 piob = ide_get_best_pio_mode(pair, 255, 4);
+			u8 piob = pair->pio_mode - XFER_PIO_0;
 
 			if (piob < cmd)
 				cmd = piob;
@@ -129,28 +129,28 @@
 
 /**
  *	cs5535_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Programs the chipset for DMA mode.
  */
 
-static void cs5535_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void cs5535_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	cs5535_set_speed(drive, speed);
+	cs5535_set_speed(drive, drive->dma_mode);
 }
 
 /**
  *	cs5535_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	A callback from the upper layers for PIO-only tuning.
  */
 
-static void cs5535_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cs5535_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	cs5535_set_speed(drive, XFER_PIO_0 + pio);
+	cs5535_set_speed(drive, drive->pio_mode);
 }
 
 static u8 cs5535_cable_detect(ide_hwif_t *hwif)
diff --git a/drivers/ide/cs5536.c b/drivers/ide/cs5536.c
index 9623b85..24214ab 100644
--- a/drivers/ide/cs5536.c
+++ b/drivers/ide/cs5536.c
@@ -125,11 +125,11 @@
 
 /**
  *	cs5536_set_pio_mode		-	PIO timing setup
+ *	@hwif: ATA port
  *	@drive: ATA device
- *	@pio: PIO mode number
  */
 
-static void cs5536_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cs5536_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u8 drv_timings[5] = {
 		0x98, 0x55, 0x32, 0x21, 0x20,
@@ -143,15 +143,16 @@
 		0x99, 0x92, 0x90, 0x22, 0x20,
 	};
 
-	struct pci_dev *pdev = to_pci_dev(drive->hwif->dev);
+	struct pci_dev *pdev = to_pci_dev(hwif->dev);
 	ide_drive_t *pair = ide_get_pair_dev(drive);
 	int cshift = (drive->dn & 1) ? IDE_CAST_D1_SHIFT : IDE_CAST_D0_SHIFT;
 	unsigned long timings = (unsigned long)ide_get_drivedata(drive);
 	u32 cast;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	u8 cmd_pio = pio;
 
 	if (pair)
-		cmd_pio = min(pio, ide_get_best_pio_mode(pair, 255, 4));
+		cmd_pio = min_t(u8, pio, pair->pio_mode - XFER_PIO_0);
 
 	timings &= (IDE_DRV_MASK << 8);
 	timings |= drv_timings[pio];
@@ -172,11 +173,11 @@
 
 /**
  *	cs5536_set_dma_mode		-	DMA timing setup
+ *	@hwif: ATA port
  *	@drive: ATA device
- *	@mode: DMA mode
  */
 
-static void cs5536_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void cs5536_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u8 udma_timings[6] = {
 		0xc2, 0xc1, 0xc0, 0xc4, 0xc5, 0xc6,
@@ -186,10 +187,11 @@
 		0x67, 0x21, 0x20,
 	};
 
-	struct pci_dev *pdev = to_pci_dev(drive->hwif->dev);
+	struct pci_dev *pdev = to_pci_dev(hwif->dev);
 	int dshift = (drive->dn & 1) ? IDE_D1_SHIFT : IDE_D0_SHIFT;
 	unsigned long timings = (unsigned long)ide_get_drivedata(drive);
 	u32 etc;
+	const u8 mode = drive->dma_mode;
 
 	cs5536_read(pdev, ETC, &etc);
 
diff --git a/drivers/ide/cy82c693.c b/drivers/ide/cy82c693.c
index d6e2cbb..9383f67 100644
--- a/drivers/ide/cy82c693.c
+++ b/drivers/ide/cy82c693.c
@@ -1,43 +1,11 @@
 /*
  *  Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
  *  Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator
+ *  Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
  *
  * CYPRESS CY82C693 chipset IDE controller
  *
  * The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards.
- * Writing the driver was quite simple, since most of the job is
- * done by the generic pci-ide support.
- * The hard part was finding the CY82C693's datasheet on Cypress's
- * web page :-(. But Altavista solved this problem :-).
- *
- *
- * Notes:
- * - I recently got a 16.8G IBM DTTA, so I was able to test it with
- *   a large and fast disk - the results look great, so I'd say the
- *   driver is working fine :-)
- *   hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA
- * - this is my first linux driver, so there's probably a lot  of room
- *   for optimizations and bug fixing, so feel free to do it.
- * - if using PIO mode it's a good idea to set the PIO mode and
- *   32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda
- * - I had some problems with my IBM DHEA with PIO modes < 2
- *   (lost interrupts) ?????
- * - first tests with DMA look okay, they seem to work, but there is a
- *   problem with sound - the BusMaster IDE TimeOut should fixed this
- *
- * Ancient History:
- * AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693
- * ASK@1999-01-23: v0.33 made a few minor code clean ups
- *                       removed DMA clock speed setting by default
- *                       added boot message
- * ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut
- *                       added support to set DMA Controller Clock Speed
- * ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes
- *                       on some drives.
- * ASK@1998-10-29: v0.3 added support to set DMA modes
- * ASK@1998-10-28: v0.2 added support to set PIO modes
- * ASK@1998-10-27: v0.1 first version - chipset detection
- *
  */
 
 #include <linux/module.h>
@@ -81,87 +49,13 @@
 #define CY82_INDEX_CHANNEL1	0x31
 #define CY82_INDEX_TIMEOUT	0x32
 
-/* the min and max PCI bus speed in MHz - from datasheet */
-#define CY82C963_MIN_BUS_SPEED	25
-#define CY82C963_MAX_BUS_SPEED	33
-
-/* the struct for the PIO mode timings */
-typedef struct pio_clocks_s {
-	u8	address_time;	/* Address setup (clocks) */
-	u8	time_16r;	/* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */
-	u8	time_16w;	/* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */
-	u8	time_8;		/* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */
-} pio_clocks_t;
-
-/*
- * calc clocks using bus_speed
- * returns (rounded up) time in bus clocks for time in ns
- */
-static int calc_clk(int time, int bus_speed)
-{
-	int clocks;
-
-	clocks = (time*bus_speed+999)/1000 - 1;
-
-	if (clocks < 0)
-		clocks = 0;
-
-	if (clocks > 0x0F)
-		clocks = 0x0F;
-
-	return clocks;
-}
-
-/*
- * compute the values for the clock registers for PIO
- * mode and pci_clk [MHz] speed
- *
- * NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used
- *       for mode 3 and 4 drives 8 and 16-bit timings are the same
- *
- */
-static void compute_clocks(u8 pio, pio_clocks_t *p_pclk)
-{
-	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
-	int clk1, clk2;
-	int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
-
-	/* we don't check against CY82C693's min and max speed,
-	 * so you can play with the idebus=xx parameter
-	 */
-
-	/* let's calc the address setup time clocks */
-	p_pclk->address_time = (u8)calc_clk(t->setup, bus_speed);
-
-	/* let's calc the active and recovery time clocks */
-	clk1 = calc_clk(t->active, bus_speed);
-
-	/* calc recovery timing */
-	clk2 = t->cycle - t->active - t->setup;
-
-	clk2 = calc_clk(clk2, bus_speed);
-
-	clk1 = (clk1<<4)|clk2;	/* combine active and recovery clocks */
-
-	/* note: we use the same values for 16bit IOR and IOW
-	 *	those are all the same, since I don't have other
-	 *	timings than those from ide-lib.c
-	 */
-
-	p_pclk->time_16r = (u8)clk1;
-	p_pclk->time_16w = (u8)clk1;
-
-	/* what are good values for 8bit ?? */
-	p_pclk->time_8 = (u8)clk1;
-}
-
 /*
  * set DMA mode a specific channel for CY82C693
  */
 
-static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void cy82c693_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
+	const u8 mode = drive->dma_mode;
 	u8 single = (mode & 0x10) >> 4, index = 0, data = 0;
 
 	index = hwif->channel ? CY82_INDEX_CHANNEL1 : CY82_INDEX_CHANNEL0;
@@ -186,12 +80,14 @@
 	outb(data, CY82_DATA_PORT);
 }
 
-static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void cy82c693_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
-	pio_clocks_t pclk;
+	int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
+	const unsigned long T = 1000000 / bus_speed;
 	unsigned int addrCtrl;
+	struct ide_timing t;
+	u8 time_16, time_8;
 
 	/* select primary or secondary channel */
 	if (hwif->index > 0) {  /* drive is on the secondary channel */
@@ -204,8 +100,12 @@
 		}
 	}
 
-	/* let's calc the values for this PIO mode */
-	compute_clocks(pio, &pclk);
+	ide_timing_compute(drive, drive->pio_mode, &t, T, 1);
+
+	time_16 = clamp_val(t.recover - 1, 0, 15) |
+		  (clamp_val(t.active - 1, 0, 15) << 4);
+	time_8 = clamp_val(t.act8b - 1, 0, 15) |
+		 (clamp_val(t.rec8b - 1, 0, 15) << 4);
 
 	/* now let's write  the clocks registers */
 	if ((drive->dn & 1) == 0) {
@@ -217,13 +117,13 @@
 		pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
 
 		addrCtrl &= (~0xF);
-		addrCtrl |= (unsigned int)pclk.address_time;
+		addrCtrl |= clamp_val(t.setup - 1, 0, 15);
 		pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
 
 		/* now let's set the remaining registers */
-		pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
-		pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
-		pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
+		pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, time_16);
+		pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, time_16);
+		pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, time_8);
 	} else {
 		/*
 		 * set slave drive
@@ -233,13 +133,13 @@
 		pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
 
 		addrCtrl &= (~0xF0);
-		addrCtrl |= ((unsigned int)pclk.address_time<<4);
+		addrCtrl |= (clamp_val(t.setup - 1, 0, 15) << 4);
 		pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
 
 		/* now let's set the remaining registers */
-		pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
-		pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
-		pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
+		pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, time_16);
+		pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, time_16);
+		pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, time_8);
 	}
 }
 
@@ -325,6 +225,6 @@
 module_init(cy82c693_ide_init);
 module_exit(cy82c693_ide_exit);
 
-MODULE_AUTHOR("Andreas Krebs, Andre Hedrick");
+MODULE_AUTHOR("Andreas Krebs, Andre Hedrick, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/dtc2278.c b/drivers/ide/dtc2278.c
index c6b1381..6929f7f 100644
--- a/drivers/ide/dtc2278.c
+++ b/drivers/ide/dtc2278.c
@@ -68,11 +68,11 @@
 
 static DEFINE_SPINLOCK(dtc2278_lock);
 
-static void dtc2278_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned long flags;
 
-	if (pio >= 3) {
+	if (drive->pio_mode >= XFER_PIO_3) {
 		spin_lock_irqsave(&dtc2278_lock, flags);
 		/*
 		 * This enables PIO mode4 (3?) on the first interface
diff --git a/drivers/ide/hpt366.c b/drivers/ide/hpt366.c
index 4d90ac2..b885c1d 100644
--- a/drivers/ide/hpt366.c
+++ b/drivers/ide/hpt366.c
@@ -627,14 +627,14 @@
 	return info->timings->clock_table[info->clock][i];
 }
 
-static void hpt3xx_set_mode(ide_drive_t *drive, const u8 speed)
+static void hpt3xx_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	struct hpt_info *info	= hpt3xx_get_info(hwif->dev);
 	struct hpt_timings *t	= info->timings;
 	u8  itr_addr		= 0x40 + (drive->dn * 4);
 	u32 old_itr		= 0;
+	const u8 speed		= drive->dma_mode;
 	u32 new_itr		= get_speed_setting(speed, info);
 	u32 itr_mask		= speed < XFER_MW_DMA_0 ? t->pio_mask :
 				 (speed < XFER_UDMA_0   ? t->dma_mask :
@@ -651,9 +651,10 @@
 	pci_write_config_dword(dev, itr_addr, new_itr);
 }
 
-static void hpt3xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void hpt3xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	hpt3xx_set_mode(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	hpt3xx_set_mode(hwif, drive);
 }
 
 static void hpt3xx_maskproc(ide_drive_t *drive, int mask)
diff --git a/drivers/ide/ht6560b.c b/drivers/ide/ht6560b.c
index aafed80..d81e496 100644
--- a/drivers/ide/ht6560b.c
+++ b/drivers/ide/ht6560b.c
@@ -279,9 +279,10 @@
 #endif
 }
 
-static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void ht6560b_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned long flags, config;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	u8 timing;
 	
 	switch (pio) {
diff --git a/drivers/ide/icside.c b/drivers/ide/icside.c
index 0f67f1a..4a697a2 100644
--- a/drivers/ide/icside.c
+++ b/drivers/ide/icside.c
@@ -65,6 +65,8 @@
 };
 
 struct icside_state {
+	unsigned int channel;
+	unsigned int enabled;
 	void __iomem *irq_port;
 	void __iomem *ioc_base;
 	unsigned int sel;
@@ -114,11 +116,18 @@
 	struct icside_state *state = ec->irq_data;
 	void __iomem *base = state->irq_port;
 
-	writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
-	readb(base + ICS_ARCIN_V6_INTROFFSET_2);
+	state->enabled = 1;
 
-	writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
-	readb(base + ICS_ARCIN_V6_INTROFFSET_1);
+	switch (state->channel) {
+	case 0:
+		writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
+		readb(base + ICS_ARCIN_V6_INTROFFSET_2);
+		break;
+	case 1:
+		writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
+		readb(base + ICS_ARCIN_V6_INTROFFSET_1);
+		break;
+	}
 }
 
 /* Prototype: icside_irqdisable_arcin_v6 (struct expansion_card *ec, int irqnr)
@@ -128,6 +137,8 @@
 {
 	struct icside_state *state = ec->irq_data;
 
+	state->enabled = 0;
+
 	readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
 	readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
 }
@@ -149,6 +160,44 @@
 	.irqpending	= icside_irqpending_arcin_v6,
 };
 
+/*
+ * Handle routing of interrupts.  This is called before
+ * we write the command to the drive.
+ */
+static void icside_maskproc(ide_drive_t *drive, int mask)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct expansion_card *ec = ECARD_DEV(hwif->dev);
+	struct icside_state *state = ecard_get_drvdata(ec);
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	state->channel = hwif->channel;
+
+	if (state->enabled && !mask) {
+		switch (hwif->channel) {
+		case 0:
+			writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+			readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+			break;
+		case 1:
+			writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+			readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+			break;
+		}
+	} else {
+		readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+		readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+	}
+
+	local_irq_restore(flags);
+}
+
+static const struct ide_port_ops icside_v6_no_dma_port_ops = {
+	.maskproc		= icside_maskproc,
+};
+
 #ifdef CONFIG_BLK_DEV_IDEDMA_ICS
 /*
  * SG-DMA support.
@@ -185,10 +234,11 @@
  *	MW1	80	50	50	150	C
  *	MW2	70	25	25	120	C
  */
-static void icside_set_dma_mode(ide_drive_t *drive, const u8 xfer_mode)
+static void icside_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned long cycle_time;
 	int use_dma_info = 0;
+	const u8 xfer_mode = drive->dma_mode;
 
 	switch (xfer_mode) {
 	case XFER_MW_DMA_2:
@@ -228,6 +278,7 @@
 
 static const struct ide_port_ops icside_v6_port_ops = {
 	.set_dma_mode		= icside_set_dma_mode,
+	.maskproc		= icside_maskproc,
 };
 
 static void icside_dma_host_set(ide_drive_t *drive, int on)
@@ -272,6 +323,11 @@
 	BUG_ON(dma_channel_active(ec->dma));
 
 	/*
+	 * Ensure that we have the right interrupt routed.
+	 */
+	icside_maskproc(drive, 0);
+
+	/*
 	 * Route the DMA signals to the correct interface.
 	 */
 	writeb(state->sel | hwif->channel, state->ioc_base);
@@ -399,6 +455,7 @@
 
 static const struct ide_port_info icside_v6_port_info __initdata = {
 	.init_dma		= icside_dma_off_init,
+	.port_ops		= &icside_v6_no_dma_port_ops,
 	.dma_ops		= &icside_v6_dma_ops,
 	.host_flags		= IDE_HFLAG_SERIALIZE | IDE_HFLAG_MMIO,
 	.mwdma_mask		= ATA_MWDMA2,
diff --git a/drivers/ide/ide-cs.c b/drivers/ide/ide-cs.c
index dd63963..ab87e4f 100644
--- a/drivers/ide/ide-cs.c
+++ b/drivers/ide/ide-cs.c
@@ -121,19 +121,11 @@
 static void ide_detach(struct pcmcia_device *link)
 {
     ide_info_t *info = link->priv;
-    ide_hwif_t *hwif = info->host->ports[0];
-    unsigned long data_addr, ctl_addr;
 
     dev_dbg(&link->dev, "ide_detach(0x%p)\n", link);
 
-    data_addr = hwif->io_ports.data_addr;
-    ctl_addr  = hwif->io_ports.ctl_addr;
-
     ide_release(link);
 
-    release_region(ctl_addr, 1);
-    release_region(data_addr, 8);
-
     kfree(info);
 } /* ide_detach */
 
@@ -354,12 +346,19 @@
 
     dev_dbg(&link->dev, "ide_release(0x%p)\n", link);
 
-    if (info->ndev)
-	/* FIXME: if this fails we need to queue the cleanup somehow
-	   -- need to investigate the required PCMCIA magic */
-	ide_host_remove(host);
+    if (info->ndev) {
+	ide_hwif_t *hwif = host->ports[0];
+	unsigned long data_addr, ctl_addr;
 
-    info->ndev = 0;
+	data_addr = hwif->io_ports.data_addr;
+	ctl_addr = hwif->io_ports.ctl_addr;
+
+	ide_host_remove(host);
+	info->ndev = 0;
+
+	release_region(ctl_addr, 1);
+	release_region(data_addr, 8);
+    }
 
     pcmcia_disable_device(link);
 } /* ide_release */
diff --git a/drivers/ide/ide-devsets.c b/drivers/ide/ide-devsets.c
index 1099bf7..c6935c7 100644
--- a/drivers/ide/ide-devsets.c
+++ b/drivers/ide/ide-devsets.c
@@ -105,15 +105,17 @@
 		return -ENOSYS;
 
 	if (set_pio_mode_abuse(drive->hwif, arg)) {
+		drive->pio_mode = arg + XFER_PIO_0;
+
 		if (arg == 8 || arg == 9) {
 			unsigned long flags;
 
 			/* take lock for IDE_DFLAG_[NO_]UNMASK/[NO_]IO_32BIT */
 			spin_lock_irqsave(&hwif->lock, flags);
-			port_ops->set_pio_mode(drive, arg);
+			port_ops->set_pio_mode(hwif, drive);
 			spin_unlock_irqrestore(&hwif->lock, flags);
 		} else
-			port_ops->set_pio_mode(drive, arg);
+			port_ops->set_pio_mode(hwif, drive);
 	} else {
 		int keep_dma = !!(drive->dev_flags & IDE_DFLAG_USING_DMA);
 
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 222c1ef..376f2dc 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -231,7 +231,7 @@
 	u16 *id = drive->id;
 	int ivb = ide_in_drive_list(id, ivb_list);
 
-	if (hwif->cbl == ATA_CBL_PATA40_SHORT)
+	if (hwif->cbl == ATA_CBL_SATA || hwif->cbl == ATA_CBL_PATA40_SHORT)
 		return 1;
 
 	if (ivb)
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index f8c1ae6..fbedd35 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -1042,6 +1042,8 @@
 		if (hwif->host_flags & IDE_HFLAG_NO_UNMASK_IRQS)
 			drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
 
+		drive->pio_mode = XFER_PIO_0;
+
 		if (port_ops && port_ops->init_dev)
 			port_ops->init_dev(drive);
 	}
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index 6a0e625..b072328 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -1365,7 +1365,7 @@
  * supported here, and not in the corresponding block interface. Our own
  * ide-tape ioctls are supported on both interfaces.
  */
-static int idetape_chrdev_ioctl(struct inode *inode, struct file *file,
+static long do_idetape_chrdev_ioctl(struct file *file,
 				unsigned int cmd, unsigned long arg)
 {
 	struct ide_tape_obj *tape = file->private_data;
@@ -1420,6 +1420,16 @@
 	}
 }
 
+static long idetape_chrdev_ioctl(struct file *file,
+				unsigned int cmd, unsigned long arg)
+{
+	long ret;
+	lock_kernel();
+	ret = do_idetape_chrdev_ioctl(file, cmd, arg);
+	unlock_kernel();
+	return ret;
+}
+
 /*
  * Do a mode sense page 0 with block descriptor and if it succeeds set the tape
  * block size with the reported value.
@@ -1888,7 +1898,7 @@
 	.owner		= THIS_MODULE,
 	.read		= idetape_chrdev_read,
 	.write		= idetape_chrdev_write,
-	.ioctl		= idetape_chrdev_ioctl,
+	.unlocked_ioctl	= idetape_chrdev_ioctl,
 	.open		= idetape_chrdev_open,
 	.release	= idetape_chrdev_release,
 };
diff --git a/drivers/ide/ide-timings.c b/drivers/ide/ide-timings.c
index 001a563..0e05f75 100644
--- a/drivers/ide/ide-timings.c
+++ b/drivers/ide/ide-timings.c
@@ -166,12 +166,13 @@
 	if (id[ATA_ID_FIELD_VALID] & 2) {	/* EIDE drive */
 		memset(&p, 0, sizeof(p));
 
-		if (speed <= XFER_PIO_2)
-			p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
-		else if ((speed <= XFER_PIO_4) ||
-			 (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
-			p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
-		else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+		if (speed >= XFER_PIO_0 && speed < XFER_SW_DMA_0) {
+			if (speed <= XFER_PIO_2)
+				p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
+			else if ((speed <= XFER_PIO_4) ||
+				 (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
+				p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
+		} else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
 			p.cycle = id[ATA_ID_EIDE_DMA_MIN];
 
 		ide_timing_merge(&p, t, t, IDE_TIMING_CYCLE | IDE_TIMING_CYC8B);
@@ -185,11 +186,10 @@
 	/*
 	 * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
 	 * S.M.A.R.T and some other commands. We have to ensure that the
-	 * DMA cycle timing is slower/equal than the fastest PIO timing.
+	 * DMA cycle timing is slower/equal than the current PIO timing.
 	 */
 	if (speed >= XFER_SW_DMA_0) {
-		u8 pio = ide_get_best_pio_mode(drive, 255, 5);
-		ide_timing_compute(drive, XFER_PIO_0 + pio, &p, T, UT);
+		ide_timing_compute(drive, drive->pio_mode, &p, T, UT);
 		ide_timing_merge(&p, t, t, IDE_TIMING_ALL);
 	}
 
diff --git a/drivers/ide/ide-xfer-mode.c b/drivers/ide/ide-xfer-mode.c
index 46d203c..5fc8d5c 100644
--- a/drivers/ide/ide-xfer-mode.c
+++ b/drivers/ide/ide-xfer-mode.c
@@ -58,7 +58,7 @@
  *	This is used by most chipset support modules when "auto-tuning".
  */
 
-u8 ide_get_best_pio_mode(ide_drive_t *drive, u8 mode_wanted, u8 max_mode)
+static u8 ide_get_best_pio_mode(ide_drive_t *drive, u8 mode_wanted, u8 max_mode)
 {
 	u16 *id = drive->id;
 	int pio_mode = -1, overridden = 0;
@@ -105,7 +105,6 @@
 
 	return pio_mode;
 }
-EXPORT_SYMBOL_GPL(ide_get_best_pio_mode);
 
 int ide_pio_need_iordy(ide_drive_t *drive, const u8 pio)
 {
@@ -135,17 +134,20 @@
 	 * set transfer mode on the device in ->set_pio_mode method...
 	 */
 	if (port_ops->set_dma_mode == NULL) {
-		port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
+		drive->pio_mode = mode;
+		port_ops->set_pio_mode(hwif, drive);
 		return 0;
 	}
 
 	if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
 		if (ide_config_drive_speed(drive, mode))
 			return -1;
-		port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
+		drive->pio_mode = mode;
+		port_ops->set_pio_mode(hwif, drive);
 		return 0;
 	} else {
-		port_ops->set_pio_mode(drive, mode - XFER_PIO_0);
+		drive->pio_mode = mode;
+		port_ops->set_pio_mode(hwif, drive);
 		return ide_config_drive_speed(drive, mode);
 	}
 }
@@ -164,10 +166,12 @@
 	if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
 		if (ide_config_drive_speed(drive, mode))
 			return -1;
-		port_ops->set_dma_mode(drive, mode);
+		drive->dma_mode = mode;
+		port_ops->set_dma_mode(hwif, drive);
 		return 0;
 	} else {
-		port_ops->set_dma_mode(drive, mode);
+		drive->dma_mode = mode;
+		port_ops->set_dma_mode(hwif, drive);
 		return ide_config_drive_speed(drive, mode);
 	}
 }
diff --git a/drivers/ide/it8172.c b/drivers/ide/it8172.c
index 0d266a5..560e66d 100644
--- a/drivers/ide/it8172.c
+++ b/drivers/ide/it8172.c
@@ -37,12 +37,12 @@
 
 #define DRV_NAME "IT8172"
 
-static void it8172_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void it8172_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u16 drive_enables;
 	u32 drive_timing;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	/*
 	 * The highest value of DIOR/DIOW pulse width and recovery time
@@ -77,14 +77,14 @@
 	pci_write_config_dword(dev, 0x44, drive_timing);
 }
 
-static void it8172_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void it8172_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	int a_speed		= 3 << (drive->dn * 4);
 	int u_flag		= 1 << drive->dn;
 	int u_speed		= 0;
 	u8 reg48, reg4a;
+	const u8 speed		= drive->dma_mode;
 
 	pci_read_config_byte(dev, 0x48, &reg48);
 	pci_read_config_byte(dev, 0x4a, &reg4a);
@@ -98,14 +98,14 @@
 		pci_write_config_byte(dev, 0x4a, reg4a | u_speed);
 	} else {
 		const u8 mwdma_to_pio[] = { 0, 3, 4 };
-		u8 pio;
 
 		pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
 		pci_write_config_byte(dev, 0x4a, reg4a & ~a_speed);
 
-		pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+		drive->pio_mode =
+			mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
 
-		it8172_set_pio_mode(drive, pio);
+		it8172_set_pio_mode(hwif, drive);
 	}
 }
 
diff --git a/drivers/ide/it8213.c b/drivers/ide/it8213.c
index 4797616..46816ba 100644
--- a/drivers/ide/it8213.c
+++ b/drivers/ide/it8213.c
@@ -17,15 +17,14 @@
 
 /**
  *	it8213_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Set the interface PIO mode.
  */
 
-static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void it8213_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	int is_slave		= drive->dn & 1;
 	int master_port		= 0x40;
@@ -35,6 +34,7 @@
 	u8 slave_data;
 	static DEFINE_SPINLOCK(tune_lock);
 	int control = 0;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	static const u8 timings[][2] = {
 					{ 0, 0 },
@@ -74,15 +74,14 @@
 
 /**
  *	it8213_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Tune the ITE chipset for the DMA mode.
  */
 
-static void it8213_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void it8213_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 maslave		= 0x40;
 	int a_speed		= 3 << (drive->dn * 4);
@@ -92,6 +91,7 @@
 	int u_speed		= 0;
 	u16			reg4042, reg4a;
 	u8			reg48, reg54, reg55;
+	const u8 speed		= drive->dma_mode;
 
 	pci_read_config_word(dev, maslave, &reg4042);
 	pci_read_config_byte(dev, 0x48, &reg48);
@@ -120,7 +120,6 @@
 			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
 	} else {
 		const u8 mwdma_to_pio[] = { 0, 3, 4 };
-		u8 pio;
 
 		if (reg48 & u_flag)
 			pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
@@ -132,11 +131,12 @@
 			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
 
 		if (speed >= XFER_MW_DMA_0)
-			pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+			drive->pio_mode =
+				mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
 		else
-			pio = 2; /* only SWDMA2 is allowed */
+			drive->pio_mode = XFER_PIO_2; /* for SWDMA2 */
 
-		it8213_set_pio_mode(drive, pio);
+		it8213_set_pio_mode(hwif, drive);
 	}
 }
 
diff --git a/drivers/ide/it821x.c b/drivers/ide/it821x.c
index 51aa745..b2709c7 100644
--- a/drivers/ide/it821x.c
+++ b/drivers/ide/it821x.c
@@ -228,18 +228,18 @@
 
 /**
  *	it821x_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Tune the host to the desired PIO mode taking into the consideration
  *	the maximum PIO mode supported by the other device on the cable.
  */
 
-static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
 	ide_drive_t *pair = ide_get_pair_dev(drive);
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	u8 unit = drive->dn & 1, set_pio = pio;
 
 	/* Spec says 89 ref driver uses 88 */
@@ -252,7 +252,7 @@
 	 * on the cable.
 	 */
 	if (pair) {
-		u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
+		u8 pair_pio = pair->pio_mode - XFER_PIO_0;
 		/* trim PIO to the slowest of the master/slave */
 		if (pair_pio < set_pio)
 			set_pio = pair_pio;
@@ -393,14 +393,16 @@
 
 /**
  *	it821x_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Tune the ITE chipset for the desired DMA mode.
  */
 
-static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
+	const u8 speed = drive->dma_mode;
+
 	/*
 	 * MWDMA tuning is really hard because our MWDMA and PIO
 	 * timings are kept in the same place.  We can switch in the
diff --git a/drivers/ide/jmicron.c b/drivers/ide/jmicron.c
index bf2be64..74c2c4a 100644
--- a/drivers/ide/jmicron.c
+++ b/drivers/ide/jmicron.c
@@ -80,19 +80,19 @@
 	return ATA_CBL_PATA80;
 }
 
-static void jmicron_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void jmicron_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 }
 
 /**
  *	jmicron_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@mode: DMA mode
  *
  *	As the JMicron snoops for timings we don't need to do anything here.
  */
 
-static void jmicron_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void jmicron_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 }
 
diff --git a/drivers/ide/opti621.c b/drivers/ide/opti621.c
index f1d70d6..1a53a4c 100644
--- a/drivers/ide/opti621.c
+++ b/drivers/ide/opti621.c
@@ -8,77 +8,6 @@
  * Jan Harkes <jaharkes@cwi.nl>,
  * Mark Lord <mlord@pobox.com>
  * Some parts of code are from ali14xx.c and from rz1000.c.
- *
- * OPTi is trademark of OPTi, Octek is trademark of Octek.
- *
- * I used docs from OPTi databook, from ftp.opti.com, file 9123-0002.ps
- * and disassembled/traced setupvic.exe (DOS program).
- * It increases kernel code about 2 kB.
- * I don't have this card no more, but I hope I can get some in case
- * of needed development.
- * My card is Octek PIDE 1.01 (on card) or OPTiViC (program).
- * It has a place for a secondary connector in circuit, but nothing
- * is there. Also BIOS says no address for
- * secondary controller (see bellow in ide_init_opti621).
- * I've only tested this on my system, which only has one disk.
- * It's Western Digital WDAC2850, with PIO mode 3. The PCI bus
- * is at 20 MHz (I have DX2/80, I tried PCI at 40, but I got random
- * lockups). I tried the OCTEK double speed CD-ROM and
- * it does not work! But I can't boot DOS also, so it's probably
- * hardware fault. I have connected Conner 80MB, the Seagate 850MB (no
- * problems) and Seagate 1GB (as slave, WD as master). My experiences
- * with the third, 1GB drive: I got 3MB/s (hdparm), but sometimes
- * it slows to about 100kB/s! I don't know why and I have
- * not this drive now, so I can't try it again.
- * I write this driver because I lost the paper ("manual") with
- * settings of jumpers on the card and I have to boot Linux with
- * Loadlin except LILO, cause I have to run the setupvic.exe program
- * already or I get disk errors (my test: rpm -Vf
- * /usr/X11R6/bin/XF86_SVGA - or any big file).
- * Some numbers from hdparm -t /dev/hda:
- * Timing buffer-cache reads:   32 MB in  3.02 seconds =10.60 MB/sec
- * Timing buffered disk reads:  16 MB in  5.52 seconds = 2.90 MB/sec
- * I have 4 Megs/s before, but I don't know why (maybe changes
- * in hdparm test).
- * After release of 0.1, I got some successful reports, so it might work.
- *
- * The main problem with OPTi is that some timings for master
- * and slave must be the same. For example, if you have master
- * PIO 3 and slave PIO 0, driver have to set some timings of
- * master for PIO 0. Second problem is that opti621_set_pio_mode
- * got only one drive to set, but have to set both drives.
- * This is solved in compute_pios. If you don't set
- * the second drive, compute_pios use ide_get_best_pio_mode
- * for autoselect mode (you can change it to PIO 0, if you want).
- * If you then set the second drive to another PIO, the old value
- * (automatically selected) will be overrided by yours.
- * There is a 25/33MHz switch in configuration
- * register, but driver is written for use at any frequency.
- *
- * Version 0.1, Nov 8, 1996
- * by Jaromir Koutek, for 2.1.8.
- * Initial version of driver.
- *
- * Version 0.2
- * Number 0.2 skipped.
- *
- * Version 0.3, Nov 29, 1997
- * by Mark Lord (probably), for 2.1.68
- * Updates for use with new IDE block driver.
- *
- * Version 0.4, Dec 14, 1997
- * by Jan Harkes
- * Fixed some errors and cleaned the code.
- *
- * Version 0.5, Jan 2, 1998
- * by Jaromir Koutek
- * Updates for use with (again) new IDE block driver.
- * Update of documentation.
- *
- * Version 0.6, Jan 2, 1999
- * by Jaromir Koutek
- * Reversed to version 0.3 of the driver, because
- * 0.5 doesn't work.
  */
 
 #include <linux/types.h>
@@ -133,12 +62,12 @@
 	return ret;
 }
 
-static void opti621_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void opti621_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	ide_drive_t *pair = ide_get_pair_dev(drive);
 	unsigned long flags;
-	unsigned long mode = XFER_PIO_0 + pio, pair_mode;
+	unsigned long mode = drive->pio_mode, pair_mode;
+	const u8 pio = mode - XFER_PIO_0;
 	u8 tim, misc, addr_pio = pio, clk;
 
 	/* DRDY is default 2 (by OPTi Databook) */
diff --git a/drivers/ide/palm_bk3710.c b/drivers/ide/palm_bk3710.c
index f8eddf0..9e8f4e1 100644
--- a/drivers/ide/palm_bk3710.c
+++ b/drivers/ide/palm_bk3710.c
@@ -166,7 +166,7 @@
 	writel(val32, base + BK3710_DATRCVR);
 
 	if (mate) {
-		u8 mode2 = ide_get_best_pio_mode(mate, 255, 4);
+		u8 mode2 = mate->pio_mode - XFER_PIO_0;
 
 		if (mode2 < mode)
 			mode = mode2;
@@ -188,10 +188,11 @@
 	writel(val32, base + BK3710_REGRCVR);
 }
 
-static void palm_bk3710_set_dma_mode(ide_drive_t *drive, u8 xferspeed)
+static void palm_bk3710_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	int is_slave = drive->dn & 1;
-	void __iomem *base = (void *)drive->hwif->dma_base;
+	void __iomem *base = (void *)hwif->dma_base;
+	const u8 xferspeed = drive->dma_mode;
 
 	if (xferspeed >= XFER_UDMA_0) {
 		palm_bk3710_setudmamode(base, is_slave,
@@ -203,12 +204,13 @@
 	}
 }
 
-static void palm_bk3710_set_pio_mode(ide_drive_t *drive, u8 pio)
+static void palm_bk3710_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	unsigned int cycle_time;
 	int is_slave = drive->dn & 1;
 	ide_drive_t *mate;
-	void __iomem *base = (void *)drive->hwif->dma_base;
+	void __iomem *base = (void *)hwif->dma_base;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	/*
 	 * Obtain the drive PIO data for tuning the Palm Chip registers
diff --git a/drivers/ide/pdc202xx_new.c b/drivers/ide/pdc202xx_new.c
index 65ba823..9546fe2 100644
--- a/drivers/ide/pdc202xx_new.c
+++ b/drivers/ide/pdc202xx_new.c
@@ -129,11 +129,11 @@
 	{ 0x1a, 0x01, 0xcb },	/* UDMA mode 6 */
 };
 
-static void pdcnew_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void pdcnew_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 adj			= (drive->dn & 1) ? 0x08 : 0x00;
+	const u8 speed		= drive->dma_mode;
 
 	/*
 	 * IDE core issues SETFEATURES_XFER to the drive first (thanks to
@@ -167,11 +167,11 @@
  	}
 }
 
-static void pdcnew_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void pdcnew_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	if (max_dma_rate(dev) == 4) {
 		set_indexed_reg(hwif, 0x0c + adj, pio_timings[pio].reg0c);
diff --git a/drivers/ide/pdc202xx_old.c b/drivers/ide/pdc202xx_old.c
index 35161dd..c5f3841 100644
--- a/drivers/ide/pdc202xx_old.c
+++ b/drivers/ide/pdc202xx_old.c
@@ -1,7 +1,7 @@
 /*
  *  Copyright (C) 1998-2002		Andre Hedrick <andre@linux-ide.org>
  *  Copyright (C) 2006-2007, 2009	MontaVista Software, Inc.
- *  Copyright (C) 2007			Bartlomiej Zolnierkiewicz
+ *  Copyright (C) 2007-2010		Bartlomiej Zolnierkiewicz
  *
  *  Portions Copyright (C) 1999 Promise Technology, Inc.
  *  Author: Frank Tiernan (frankt@promise.com)
@@ -21,23 +21,15 @@
 
 #define DRV_NAME "pdc202xx_old"
 
-static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
-
-static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
+static void pdc202xx_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 drive_pci		= 0x60 + (drive->dn << 2);
+	const u8 speed		= drive->dma_mode;
 
 	u8			AP = 0, BP = 0, CP = 0;
 	u8			TA = 0, TB = 0, TC = 0;
 
-	/*
-	 * TODO: do this once per channel
-	 */
-	if (dev->device != PCI_DEVICE_ID_PROMISE_20246)
-		pdc_old_disable_66MHz_clock(hwif);
-
 	pci_read_config_byte(dev, drive_pci,     &AP);
 	pci_read_config_byte(dev, drive_pci + 1, &BP);
 	pci_read_config_byte(dev, drive_pci + 2, &CP);
@@ -84,9 +76,10 @@
 	}
 }
 
-static void pdc202xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void pdc202xx_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	pdc202xx_set_mode(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	pdc202xx_set_mode(hwif, drive);
 }
 
 static int pdc202xx_test_irq(ide_hwif_t *hwif)
@@ -100,13 +93,13 @@
 		 * bit 7: error, bit 6: interrupting,
 		 * bit 5: FIFO full, bit 4: FIFO empty
 		 */
-		return ((sc1d & 0x50) == 0x40) ? 1 : 0;
+		return ((sc1d & 0x50) == 0x50) ? 1 : 0;
 	} else	{
 		/*
 		 * bit 3: error, bit 2: interrupting,
 		 * bit 1: FIFO full, bit 0: FIFO empty
 		 */
-		return ((sc1d & 0x05) == 0x04) ? 1 : 0;
+		return ((sc1d & 0x05) == 0x05) ? 1 : 0;
 	}
 }
 
@@ -145,6 +138,11 @@
 	outb(clock & ~(hwif->channel ? 0x08 : 0x02), clock_reg);
 }
 
+static void pdc2026x_init_hwif(ide_hwif_t *hwif)
+{
+	pdc_old_disable_66MHz_clock(hwif);
+}
+
 static void pdc202xx_dma_start(ide_drive_t *drive)
 {
 	if (drive->current_speed > XFER_UDMA_2)
@@ -261,6 +259,7 @@
 	{ \
 		.name		= DRV_NAME, \
 		.init_chipset	= init_chipset_pdc202xx, \
+		.init_hwif	= pdc2026x_init_hwif, \
 		.port_ops	= &pdc2026x_port_ops, \
 		.dma_ops	= &pdc2026x_dma_ops, \
 		.host_flags	= IDE_HFLAGS_PDC202XX, \
@@ -356,6 +355,6 @@
 module_init(pdc202xx_ide_init);
 module_exit(pdc202xx_ide_exit);
 
-MODULE_AUTHOR("Andre Hedrick, Frank Tiernan");
+MODULE_AUTHOR("Andre Hedrick, Frank Tiernan, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("PCI driver module for older Promise IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/piix.c b/drivers/ide/piix.c
index bf14f39..1bdca49 100644
--- a/drivers/ide/piix.c
+++ b/drivers/ide/piix.c
@@ -59,15 +59,14 @@
 
 /**
  *	piix_set_pio_mode	-	set host controller for PIO mode
+ *	@port: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Set the interface PIO mode based upon the settings done by AMI BIOS.
  */
 
-static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void piix_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	int is_slave		= drive->dn & 1;
 	int master_port		= hwif->channel ? 0x42 : 0x40;
@@ -77,6 +76,7 @@
 	u8 slave_data;
 	static DEFINE_SPINLOCK(tune_lock);
 	int control = 0;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 				     /* ISP  RTC */
 	static const u8 timings[][2]= {
@@ -127,16 +127,15 @@
 
 /**
  *	piix_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Set a PIIX host controller to the desired DMA mode.  This involves
  *	programming the right timing data into the PCI configuration space.
  */
 
-static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void piix_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 maslave		= hwif->channel ? 0x42 : 0x40;
 	int a_speed		= 3 << (drive->dn * 4);
@@ -147,6 +146,7 @@
 	int			sitre;
 	u16			reg4042, reg4a;
 	u8			reg48, reg54, reg55;
+	const u8 speed		= drive->dma_mode;
 
 	pci_read_config_word(dev, maslave, &reg4042);
 	sitre = (reg4042 & 0x4000) ? 1 : 0;
@@ -176,7 +176,6 @@
 			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
 	} else {
 		const u8 mwdma_to_pio[] = { 0, 3, 4 };
-		u8 pio;
 
 		if (reg48 & u_flag)
 			pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
@@ -188,11 +187,12 @@
 			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
 
 		if (speed >= XFER_MW_DMA_0)
-			pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+			drive->pio_mode =
+				mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
 		else
-			pio = 2; /* only SWDMA2 is allowed */
+			drive->pio_mode = XFER_PIO_2; /* for SWDMA2 */
 
-		piix_set_pio_mode(drive, pio);
+		piix_set_pio_mode(hwif, drive);
 	}
 }
 
diff --git a/drivers/ide/pmac.c b/drivers/ide/pmac.c
index 7a4e788..850ee45 100644
--- a/drivers/ide/pmac.c
+++ b/drivers/ide/pmac.c
@@ -496,12 +496,11 @@
 /*
  * Old tuning functions (called on hdparm -p), sets up drive PIO timings
  */
-static void
-pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void pmac_ide_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	pmac_ide_hwif_t *pmif =
 		(pmac_ide_hwif_t *)dev_get_drvdata(hwif->gendev.parent);
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	struct ide_timing *tim = ide_timing_find_mode(XFER_PIO_0 + pio);
 	u32 *timings, t;
 	unsigned accessTicks, recTicks;
@@ -778,14 +777,14 @@
 #endif	
 }
 
-static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void pmac_ide_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	pmac_ide_hwif_t *pmif =
 		(pmac_ide_hwif_t *)dev_get_drvdata(hwif->gendev.parent);
 	int ret = 0;
 	u32 *timings, *timings2, tl[2];
 	u8 unit = drive->dn & 1;
+	const u8 speed = drive->dma_mode;
 
 	timings = &pmif->timings[unit];
 	timings2 = &pmif->timings[unit+2];
@@ -1651,8 +1650,8 @@
 		if ((status & FLUSH) == 0)
 			break;
 		if (++timeout > 100) {
-			printk(KERN_WARNING "ide%d, ide_dma_test_irq \
-			timeout flushing channel\n", hwif->index);
+			printk(KERN_WARNING "ide%d, ide_dma_test_irq timeout flushing channel\n",
+			       hwif->index);
 			break;
 		}
 	}	
diff --git a/drivers/ide/qd65xx.c b/drivers/ide/qd65xx.c
index 74696ed..3f0244f 100644
--- a/drivers/ide/qd65xx.c
+++ b/drivers/ide/qd65xx.c
@@ -189,15 +189,13 @@
 	printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
 }
 
-static void qd6500_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void qd6500_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	u16 *id = drive->id;
 	int active_time   = 175;
 	int recovery_time = 415; /* worst case values from the dos driver */
 
-	/*
-	 * FIXME: use "pio" value
-	 */
+	/* FIXME: use drive->pio_mode value */
 	if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
 	    (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
 	    id[ATA_ID_EIDE_PIO] >= 240) {
@@ -211,9 +209,9 @@
 				active_time, recovery_time));
 }
 
-static void qd6580_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void qd6580_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 	unsigned int cycle_time;
 	int active_time   = 175;
diff --git a/drivers/ide/sc1200.c b/drivers/ide/sc1200.c
index d467478..134f1fd 100644
--- a/drivers/ide/sc1200.c
+++ b/drivers/ide/sc1200.c
@@ -122,13 +122,13 @@
 	return mask;
 }
 
-static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void sc1200_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t		*hwif = drive->hwif;
 	struct pci_dev		*dev = to_pci_dev(hwif->dev);
 	unsigned int		reg, timings;
 	unsigned short		pci_clock;
 	unsigned int		basereg = hwif->channel ? 0x50 : 0x40;
+	const u8		mode = drive->dma_mode;
 
 	static const u32 udma_timing[3][3] = {
 		{ 0x00921250, 0x00911140, 0x00911030 },
@@ -193,10 +193,10 @@
  * will have valid default PIO timings set up before we get here.
  */
 
-static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void sc1200_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t	*hwif = drive->hwif;
 	int		mode = -1;
+	const u8	pio = drive->pio_mode - XFER_PIO_0;
 
 	/*
 	 * bad abuse of ->set_pio_mode interface
diff --git a/drivers/ide/scc_pata.c b/drivers/ide/scc_pata.c
index 1104bb3..b7f5b0c 100644
--- a/drivers/ide/scc_pata.c
+++ b/drivers/ide/scc_pata.c
@@ -199,16 +199,15 @@
 
 /**
  *	scc_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Load the timing settings for this device mode into the
  *	controller.
  */
 
-static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void scc_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct scc_ports *ports = ide_get_hwifdata(hwif);
 	unsigned long ctl_base = ports->ctl;
 	unsigned long cckctrl_port = ctl_base + 0xff0;
@@ -216,6 +215,7 @@
 	unsigned long pioct_port = ctl_base + 0x004;
 	unsigned long reg;
 	int offset;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	reg = in_be32((void __iomem *)cckctrl_port);
 	if (reg & CCKCTRL_ATACLKOEN) {
@@ -231,16 +231,15 @@
 
 /**
  *	scc_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Load the timing settings for this device mode into the
  *	controller.
  */
 
-static void scc_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void scc_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct scc_ports *ports = ide_get_hwifdata(hwif);
 	unsigned long ctl_base = ports->ctl;
 	unsigned long cckctrl_port = ctl_base + 0xff0;
@@ -254,6 +253,7 @@
 	int offset, idx;
 	unsigned long reg;
 	unsigned long jcactsel;
+	const u8 speed = drive->dma_mode;
 
 	reg = in_be32((void __iomem *)cckctrl_port);
 	if (reg & CCKCTRL_ATACLKOEN) {
@@ -872,20 +872,18 @@
 	.remove = __devexit_p(scc_remove),
 };
 
-static int scc_ide_init(void)
+static int __init scc_ide_init(void)
 {
 	return ide_pci_register_driver(&scc_pci_driver);
 }
 
-module_init(scc_ide_init);
-/* -- No exit code?
-static void scc_ide_exit(void)
+static void __exit scc_ide_exit(void)
 {
-	ide_pci_unregister_driver(&scc_pci_driver);
+	pci_unregister_driver(&scc_pci_driver);
 }
-module_exit(scc_ide_exit);
- */
 
+module_init(scc_ide_init);
+module_exit(scc_ide_exit);
 
 MODULE_DESCRIPTION("PCI driver module for Toshiba SCC IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/serverworks.c b/drivers/ide/serverworks.c
index b6554ef..35fb8da 100644
--- a/drivers/ide/serverworks.c
+++ b/drivers/ide/serverworks.c
@@ -2,7 +2,7 @@
  * Copyright (C) 1998-2000 Michel Aubry
  * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
  * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C)      2007 Bartlomiej Zolnierkiewicz
+ * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz
  * Portions copyright (c) 2001 Sun Microsystems
  *
  *
@@ -52,8 +52,6 @@
 	NULL
 };
 
-static struct pci_dev *isa_dev;
-
 static int check_in_drive_lists (ide_drive_t *drive, const char **list)
 {
 	char *m = (char *)&drive->id[ATA_ID_PROD];
@@ -67,26 +65,14 @@
 static u8 svwks_udma_filter(ide_drive_t *drive)
 {
 	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-	u8 mask = 0;
 
-	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
+	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
 		return 0x1f;
-	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
-		u32 reg = 0;
-		if (isa_dev)
-			pci_read_config_dword(isa_dev, 0x64, &reg);
-			
-		/*
-		 *	Don't enable UDMA on disk devices for the moment
-		 */
-		if(drive->media == ide_disk)
-			return 0;
-		/* Check the OSB4 DMA33 enable bit */
-		return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
 	} else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
 		return 0x07;
-	} else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
-		u8 btr = 0, mode;
+	} else {
+		u8 btr = 0, mode, mask;
+
 		pci_read_config_byte(dev, 0x5A, &btr);
 		mode = btr & 0x3;
 
@@ -101,13 +87,9 @@
 		case 1:	 mask = 0x07; break;
 		default: mask = 0x00; break;
 		}
-	}
-	if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
-	     (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
-	    (!(PCI_FUNC(dev->devfn) & 1)))
-		mask = 0x1f;
 
-	return mask;
+		return mask;
+	}
 }
 
 static u8 svwks_csb_check (struct pci_dev *dev)
@@ -124,12 +106,13 @@
 	return 0;
 }
 
-static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void svwks_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 	static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
 
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+	struct pci_dev *dev = to_pci_dev(hwif->dev);
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
 
@@ -145,14 +128,14 @@
 	}
 }
 
-static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void svwks_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u8 udma_modes[]		= { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
 	static const u8 dma_modes[]		= { 0x77, 0x21, 0x20 };
 	static const u8 drive_pci2[]		= { 0x45, 0x44, 0x47, 0x46 };
 
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	const u8 speed		= drive->dma_mode;
 	u8 unit			= drive->dn & 1;
 
 	u8 ultra_enable	 = 0, ultra_timing = 0, dma_timing = 0;
@@ -185,8 +168,9 @@
 
 	/* OSB4 : South Bridge and IDE */
 	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
-		isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
-			  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
+		struct pci_dev *isa_dev =
+			pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+					PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 		if (isa_dev) {
 			pci_read_config_dword(isa_dev, 0x64, &reg);
 			reg &= ~0x00002000; /* disable 600ns interrupt mask */
@@ -195,6 +179,7 @@
 					"enabled.\n", pci_name(dev));
 			reg |=  0x00004000; /* enable UDMA/33 support */
 			pci_write_config_dword(isa_dev, 0x64, reg);
+			pci_dev_put(isa_dev);
 		}
 	}
 
@@ -343,7 +328,6 @@
 static const struct ide_port_ops osb4_port_ops = {
 	.set_pio_mode		= svwks_set_pio_mode,
 	.set_dma_mode		= svwks_set_dma_mode,
-	.udma_filter		= svwks_udma_filter,
 };
 
 static const struct ide_port_ops svwks_port_ops = {
@@ -460,6 +444,6 @@
 module_init(svwks_ide_init);
 module_exit(svwks_ide_exit);
 
-MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
+MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
 MODULE_LICENSE("GPL");
diff --git a/drivers/ide/sgiioc4.c b/drivers/ide/sgiioc4.c
index b7d61dc..e3ea591 100644
--- a/drivers/ide/sgiioc4.c
+++ b/drivers/ide/sgiioc4.c
@@ -255,7 +255,7 @@
 	return dma_stat;
 }
 
-static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void sgiioc4_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 }
 
diff --git a/drivers/ide/siimage.c b/drivers/ide/siimage.c
index d95df52..ddeda44 100644
--- a/drivers/ide/siimage.c
+++ b/drivers/ide/siimage.c
@@ -229,19 +229,18 @@
 
 /**
  *	sil_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	Load the timing settings for this device mode into the
  *	controller.
  */
 
-static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
+static void sil_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u16 tf_speed[]   = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
 	static const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
 
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	ide_drive_t *pair	= ide_get_pair_dev(drive);
 	u32 speedt		= 0;
@@ -249,6 +248,7 @@
 	unsigned long addr	= siimage_seldev(drive, 0x04);
 	unsigned long tfaddr	= siimage_selreg(hwif,	0x02);
 	unsigned long base	= (unsigned long)hwif->hwif_data;
+	const u8 pio		= drive->pio_mode - XFER_PIO_0;
 	u8 tf_pio		= pio;
 	u8 mmio			= (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0;
 	u8 addr_mask		= hwif->channel ? (mmio ? 0xF4 : 0x84)
@@ -258,7 +258,7 @@
 
 	/* trim *taskfile* PIO to the slowest of the master/slave */
 	if (pair) {
-		u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);
+		u8 pair_pio = pair->pio_mode - XFER_PIO_0;
 
 		if (pair_pio < tf_pio)
 			tf_pio = pair_pio;
@@ -289,19 +289,18 @@
 
 /**
  *	sil_set_dma_mode	-	set host controller for DMA mode
+ *	@hwif: port
  *	@drive: drive
- *	@speed: DMA mode
  *
  *	Tune the SiI chipset for the desired DMA mode.
  */
 
-static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void sil_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static const u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
 	static const u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
 	static const u16 dma[]	 = { 0x2208, 0x10C2, 0x10C1 };
 
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	unsigned long base	= (unsigned long)hwif->hwif_data;
 	u16 ultra = 0, multi	= 0;
@@ -311,6 +310,7 @@
 						: (mmio ? 0xB4 : 0x80);
 	unsigned long ma	= siimage_seldev(drive, 0x08);
 	unsigned long ua	= siimage_seldev(drive, 0x0C);
+	const u8 speed		= drive->dma_mode;
 
 	scsc  = sil_ioread8 (dev, base + (mmio ? 0x4A : 0x8A));
 	mode  = sil_ioread8 (dev, base + addr_mask);
diff --git a/drivers/ide/sis5513.c b/drivers/ide/sis5513.c
index 4687060..db7f4e7 100644
--- a/drivers/ide/sis5513.c
+++ b/drivers/ide/sis5513.c
@@ -290,10 +290,10 @@
 		pci_write_config_byte(dev, 0x4b, rw_prefetch);
 }
 
-static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void sis_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	config_drive_art_rwp(drive);
-	sis_program_timings(drive, XFER_PIO_0 + pio);
+	sis_program_timings(drive, drive->pio_mode);
 }
 
 static void sis_ata133_program_udma_timings(ide_drive_t *drive, const u8 mode)
@@ -340,8 +340,10 @@
 		sis_ata33_program_udma_timings(drive, mode);
 }
 
-static void sis_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void sis_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
+	const u8 speed = drive->dma_mode;
+
 	if (speed >= XFER_UDMA_0)
 		sis_program_udma_timings(drive, speed);
 	else
diff --git a/drivers/ide/sl82c105.c b/drivers/ide/sl82c105.c
index 3c2bbf0..f21dc2a 100644
--- a/drivers/ide/sl82c105.c
+++ b/drivers/ide/sl82c105.c
@@ -63,12 +63,13 @@
 /*
  * Configure the chipset for PIO mode.
  */
-static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void sl82c105_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	struct pci_dev *dev	= to_pci_dev(drive->hwif->dev);
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	unsigned long timings	= (unsigned long)ide_get_drivedata(drive);
 	int reg			= 0x44 + drive->dn * 4;
 	u16 drv_ctrl;
+	const u8 pio		= drive->pio_mode - XFER_PIO_0;
 
 	drv_ctrl = get_pio_timings(drive, pio);
 
@@ -91,11 +92,12 @@
 /*
  * Configure the chipset for DMA mode.
  */
-static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void sl82c105_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
 	static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
 	unsigned long timings = (unsigned long)ide_get_drivedata(drive);
 	u16 drv_ctrl;
+	const u8 speed = drive->dma_mode;
 
 	drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
 
diff --git a/drivers/ide/slc90e66.c b/drivers/ide/slc90e66.c
index 1ccfb40..864ffe0 100644
--- a/drivers/ide/slc90e66.c
+++ b/drivers/ide/slc90e66.c
@@ -18,9 +18,8 @@
 
 static DEFINE_SPINLOCK(slc90e66_lock);
 
-static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void slc90e66_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	int is_slave		= drive->dn & 1;
 	int master_port		= hwif->channel ? 0x42 : 0x40;
@@ -29,6 +28,8 @@
 	u16 master_data;
 	u8 slave_data;
 	int control = 0;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
+
 				     /* ISP  RTC */
 	static const u8 timings[][2] = {
 					{ 0, 0 },
@@ -71,14 +72,14 @@
 	spin_unlock_irqrestore(&slc90e66_lock, flags);
 }
 
-static void slc90e66_set_dma_mode(ide_drive_t *drive, const u8 speed)
+static void slc90e66_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	struct pci_dev *dev	= to_pci_dev(hwif->dev);
 	u8 maslave		= hwif->channel ? 0x42 : 0x40;
 	int sitre = 0, a_speed	= 7 << (drive->dn * 4);
 	int u_speed = 0, u_flag = 1 << drive->dn;
 	u16			reg4042, reg44, reg48, reg4a;
+	const u8 speed		= drive->dma_mode;
 
 	pci_read_config_word(dev, maslave, &reg4042);
 	sitre = (reg4042 & 0x4000) ? 1 : 0;
@@ -98,7 +99,6 @@
 		}
 	} else {
 		const u8 mwdma_to_pio[] = { 0, 3, 4 };
-		u8 pio;
 
 		if (reg48 & u_flag)
 			pci_write_config_word(dev, 0x48, reg48 & ~u_flag);
@@ -106,11 +106,12 @@
 			pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
 
 		if (speed >= XFER_MW_DMA_0)
-			pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+			drive->pio_mode =
+				mwdma_to_pio[speed - XFER_MW_DMA_0] + XFER_PIO_0;
 		else
-			pio = 2; /* only SWDMA2 is allowed */
+			drive->pio_mode = XFER_PIO_2; /* for SWDMA2 */
 
-		slc90e66_set_pio_mode(drive, pio);
+		slc90e66_set_pio_mode(hwif, drive);
 	}
 }
 
diff --git a/drivers/ide/tc86c001.c b/drivers/ide/tc86c001.c
index 05a93d6..e444d24 100644
--- a/drivers/ide/tc86c001.c
+++ b/drivers/ide/tc86c001.c
@@ -13,11 +13,11 @@
 
 #define DRV_NAME "tc86c001"
 
-static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
+static void tc86c001_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif	= drive->hwif;
 	unsigned long scr_port	= hwif->config_data + (drive->dn ? 0x02 : 0x00);
 	u16 mode, scr		= inw(scr_port);
+	const u8 speed		= drive->dma_mode;
 
 	switch (speed) {
 	case XFER_UDMA_4:	mode = 0x00c0; break;
@@ -41,9 +41,10 @@
 	outw(scr, scr_port);
 }
 
-static void tc86c001_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void tc86c001_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	tc86c001_set_mode(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	tc86c001_set_mode(hwif, drive);
 }
 
 /*
diff --git a/drivers/ide/triflex.c b/drivers/ide/triflex.c
index 8773c3b..7953447 100644
--- a/drivers/ide/triflex.c
+++ b/drivers/ide/triflex.c
@@ -34,9 +34,8 @@
 
 #define DRV_NAME "triflex"
 
-static void triflex_set_mode(ide_drive_t *drive, const u8 speed)
+static void triflex_set_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	u32 triflex_timings = 0;
 	u16 timing = 0;
@@ -44,7 +43,7 @@
 
 	pci_read_config_dword(dev, channel_offset, &triflex_timings);
 
-	switch(speed) {
+	switch (drive->dma_mode) {
 		case XFER_MW_DMA_2:
 			timing = 0x0103; 
 			break;
@@ -82,9 +81,10 @@
 	pci_write_config_dword(dev, channel_offset, triflex_timings);
 }
 
-static void triflex_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void triflex_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	triflex_set_mode(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	triflex_set_mode(hwif, drive);
 }
 
 static const struct ide_port_ops triflex_port_ops = {
diff --git a/drivers/ide/tx4938ide.c b/drivers/ide/tx4938ide.c
index fd59c0d..1d80f1f 100644
--- a/drivers/ide/tx4938ide.c
+++ b/drivers/ide/tx4938ide.c
@@ -56,16 +56,15 @@
 		     &tx4938_ebuscptr->cr[ebus_ch]);
 }
 
-static void tx4938ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void tx4938ide_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	struct tx4938ide_platform_info *pdata = hwif->dev->platform_data;
-	u8 safe = pio;
+	u8 safe = drive->pio_mode - XFER_PIO_0;
 	ide_drive_t *pair;
 
 	pair = ide_get_pair_dev(drive);
 	if (pair)
-		safe = min(safe, ide_get_best_pio_mode(pair, 255, 5));
+		safe = min(safe, pair->pio_mode - XFER_PIO_0);
 	tx4938ide_tune_ebusc(pdata->ebus_ch, pdata->gbus_clock, safe);
 }
 
diff --git a/drivers/ide/tx4939ide.c b/drivers/ide/tx4939ide.c
index 64b58ec..3c73677 100644
--- a/drivers/ide/tx4939ide.c
+++ b/drivers/ide/tx4939ide.c
@@ -104,17 +104,17 @@
 
 #define TX4939IDE_BASE(hwif)	((void __iomem *)(hwif)->extra_base)
 
-static void tx4939ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void tx4939ide_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	int is_slave = drive->dn;
 	u32 mask, val;
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 	u8 safe = pio;
 	ide_drive_t *pair;
 
 	pair = ide_get_pair_dev(drive);
 	if (pair)
-		safe = min(safe, ide_get_best_pio_mode(pair, 255, 4));
+		safe = min(safe, pair->pio_mode - XFER_PIO_0);
 	/*
 	 * Update Command Transfer Mode for master/slave and Data
 	 * Transfer Mode for this drive.
@@ -125,10 +125,10 @@
 	/* tx4939ide_tf_load_fixup() will set the Sys_Ctl register */
 }
 
-static void tx4939ide_set_dma_mode(ide_drive_t *drive, const u8 mode)
+static void tx4939ide_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	u32 mask, val;
+	const u8 mode = drive->dma_mode;
 
 	/* Update Data Transfer Mode for this drive. */
 	if (mode >= XFER_UDMA_0)
diff --git a/drivers/ide/umc8672.c b/drivers/ide/umc8672.c
index 60f936e..47adcd0 100644
--- a/drivers/ide/umc8672.c
+++ b/drivers/ide/umc8672.c
@@ -104,10 +104,11 @@
 		speeds[0], speeds[1], speeds[2], speeds[3]);
 }
 
-static void umc_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void umc_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif, *mate = hwif->mate;
+	ide_hwif_t *mate = hwif->mate;
 	unsigned long uninitialized_var(flags);
+	const u8 pio = drive->pio_mode - XFER_PIO_0;
 
 	printk("%s: setting umc8672 to PIO mode%d (speed %d)\n",
 		drive->name, pio, pio_to_umc[pio]);
diff --git a/drivers/ide/via82cxxx.c b/drivers/ide/via82cxxx.c
index 028de26..e65d010 100644
--- a/drivers/ide/via82cxxx.c
+++ b/drivers/ide/via82cxxx.c
@@ -6,7 +6,7 @@
  *   vt8235, vt8237, vt8237a
  *
  * Copyright (c) 2000-2002 Vojtech Pavlik
- * Copyright (c) 2007 Bartlomiej Zolnierkiewicz
+ * Copyright (c) 2007-2010 Bartlomiej Zolnierkiewicz
  *
  * Based on the work of:
  *	Michel Aubry
@@ -54,6 +54,11 @@
 #define VIA_NO_UNMASK		0x08 /* Doesn't work with IRQ unmasking on */
 #define VIA_BAD_ID		0x10 /* Has wrong vendor ID (0x1107) */
 #define VIA_BAD_AST		0x20 /* Don't touch Address Setup Timing */
+#define VIA_SATA_PATA		0x80 /* SATA/PATA combined configuration */
+
+enum {
+	VIA_IDFLAG_SINGLE = (1 << 1), /* single channel controller */
+};
 
 /*
  * VIA SouthBridge chips.
@@ -67,11 +72,13 @@
 	u8 udma_mask;
 	u8 flags;
 } via_isa_bridges[] = {
-	{ "vx855",	PCI_DEVICE_ID_VIA_VX855,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
-	{ "vx800",	PCI_DEVICE_ID_VIA_VX800,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
-	{ "cx700",	PCI_DEVICE_ID_VIA_CX700,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+	{ "vx855",	PCI_DEVICE_ID_VIA_VX855,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+	{ "vx800",	PCI_DEVICE_ID_VIA_VX800,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+	{ "cx700",	PCI_DEVICE_ID_VIA_CX700,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+	{ "vt8261",	PCI_DEVICE_ID_VIA_8261,     0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
 	{ "vt8237s",	PCI_DEVICE_ID_VIA_8237S,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
 	{ "vt6410",	PCI_DEVICE_ID_VIA_6410,     0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+	{ "vt6415",	PCI_DEVICE_ID_VIA_6410,     0x00, 0xff, ATA_UDMA6, VIA_BAD_AST },
 	{ "vt8251",	PCI_DEVICE_ID_VIA_8251,     0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
 	{ "vt8237",	PCI_DEVICE_ID_VIA_8237,     0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
 	{ "vt8237a",	PCI_DEVICE_ID_VIA_8237A,    0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
@@ -92,6 +99,7 @@
 	{ "vt82c586",	PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f,      0x00, VIA_SET_FIFO },
 	{ "vt82c576",	PCI_DEVICE_ID_VIA_82C576,   0x00, 0x2f,      0x00, VIA_SET_FIFO | VIA_NO_UNMASK },
 	{ "vt82c576",	PCI_DEVICE_ID_VIA_82C576,   0x00, 0x2f,      0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
+	{ "vtxxxx",	PCI_DEVICE_ID_VIA_ANON,     0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
 	{ NULL }
 };
 
@@ -102,6 +110,7 @@
 {
 	struct via_isa_bridge *via_config;
 	unsigned int via_80w;
+	u8 cached_device[2];
 };
 
 /**
@@ -137,30 +146,45 @@
 	case ATA_UDMA4: t = timing->udma ? (0xe8 | (clamp_val(timing->udma, 2, 9) - 2)) : 0x0f; break;
 	case ATA_UDMA5: t = timing->udma ? (0xe0 | (clamp_val(timing->udma, 2, 9) - 2)) : 0x07; break;
 	case ATA_UDMA6: t = timing->udma ? (0xe0 | (clamp_val(timing->udma, 2, 9) - 2)) : 0x07; break;
-	default: return;
 	}
 
-	pci_write_config_byte(dev, VIA_UDMA_TIMING + (3 - dn), t);
+	/* Set UDMA unless device is not UDMA capable */
+	if (vdev->via_config->udma_mask) {
+		u8 udma_etc;
+
+		pci_read_config_byte(dev, VIA_UDMA_TIMING + 3 - dn, &udma_etc);
+
+		/* clear transfer mode bit */
+		udma_etc &= ~0x20;
+
+		if (timing->udma) {
+			/* preserve 80-wire cable detection bit */
+			udma_etc &= 0x10;
+			udma_etc |= t;
+		}
+
+		pci_write_config_byte(dev, VIA_UDMA_TIMING + 3 - dn, udma_etc);
+	}
 }
 
 /**
  *	via_set_drive		-	configure transfer mode
+ *	@hwif: port
  *	@drive: Drive to set up
- *	@speed: desired speed
  *
  *	via_set_drive() computes timing values configures the chipset to
  *	a desired transfer mode.  It also can be called by upper layers.
  */
 
-static void via_set_drive(ide_drive_t *drive, const u8 speed)
+static void via_set_drive(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	ide_hwif_t *hwif = drive->hwif;
 	ide_drive_t *peer = ide_get_pair_dev(drive);
 	struct pci_dev *dev = to_pci_dev(hwif->dev);
 	struct ide_host *host = pci_get_drvdata(dev);
 	struct via82cxxx_dev *vdev = host->host_priv;
 	struct ide_timing t, p;
 	unsigned int T, UT;
+	const u8 speed = drive->dma_mode;
 
 	T = 1000000000 / via_clock;
 
@@ -175,7 +199,7 @@
 	ide_timing_compute(drive, speed, &t, T, UT);
 
 	if (peer) {
-		ide_timing_compute(peer, peer->current_speed, &p, T, UT);
+		ide_timing_compute(peer, peer->pio_mode, &p, T, UT);
 		ide_timing_merge(&p, &t, &t, IDE_TIMING_8BIT);
 	}
 
@@ -184,22 +208,24 @@
 
 /**
  *	via_set_pio_mode	-	set host controller for PIO mode
+ *	@hwif: port
  *	@drive: drive
- *	@pio: PIO mode number
  *
  *	A callback from the upper layers for PIO-only tuning.
  */
 
-static void via_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static void via_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 {
-	via_set_drive(drive, XFER_PIO_0 + pio);
+	drive->dma_mode = drive->pio_mode;
+	via_set_drive(hwif, drive);
 }
 
 static struct via_isa_bridge *via_config_find(struct pci_dev **isa)
 {
 	struct via_isa_bridge *via_config;
 
-	for (via_config = via_isa_bridges; via_config->id; via_config++)
+	for (via_config = via_isa_bridges;
+	     via_config->id != PCI_DEVICE_ID_VIA_ANON; via_config++)
 		if ((*isa = pci_get_device(PCI_VENDOR_ID_VIA +
 			!!(via_config->flags & VIA_BAD_ID),
 			via_config->id, NULL))) {
@@ -362,6 +388,9 @@
 	if (via_cable_override(pdev))
 		return ATA_CBL_PATA40_SHORT;
 
+	if ((vdev->via_config->flags & VIA_SATA_PATA) && hwif->channel == 0)
+		return ATA_CBL_SATA;
+
 	if ((vdev->via_80w >> hwif->channel) & 1)
 		return ATA_CBL_PATA80;
 	else
@@ -374,10 +403,66 @@
 	.cable_detect		= via82cxxx_cable_detect,
 };
 
+static void via_write_devctl(ide_hwif_t *hwif, u8 ctl)
+{
+	struct via82cxxx_dev *vdev = hwif->host->host_priv;
+
+	outb(ctl, hwif->io_ports.ctl_addr);
+	outb(vdev->cached_device[hwif->channel], hwif->io_ports.device_addr);
+}
+
+static void __via_dev_select(ide_drive_t *drive, u8 select)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct via82cxxx_dev *vdev = hwif->host->host_priv;
+
+	outb(select, hwif->io_ports.device_addr);
+	vdev->cached_device[hwif->channel] = select;
+}
+
+static void via_dev_select(ide_drive_t *drive)
+{
+	__via_dev_select(drive, drive->select | ATA_DEVICE_OBS);
+}
+
+static void via_tf_load(ide_drive_t *drive, struct ide_taskfile *tf, u8 valid)
+{
+	ide_hwif_t *hwif = drive->hwif;
+	struct ide_io_ports *io_ports = &hwif->io_ports;
+
+	if (valid & IDE_VALID_FEATURE)
+		outb(tf->feature, io_ports->feature_addr);
+	if (valid & IDE_VALID_NSECT)
+		outb(tf->nsect, io_ports->nsect_addr);
+	if (valid & IDE_VALID_LBAL)
+		outb(tf->lbal, io_ports->lbal_addr);
+	if (valid & IDE_VALID_LBAM)
+		outb(tf->lbam, io_ports->lbam_addr);
+	if (valid & IDE_VALID_LBAH)
+		outb(tf->lbah, io_ports->lbah_addr);
+	if (valid & IDE_VALID_DEVICE)
+		__via_dev_select(drive, tf->device);
+}
+
+const struct ide_tp_ops via_tp_ops = {
+	.exec_command		= ide_exec_command,
+	.read_status		= ide_read_status,
+	.read_altstatus		= ide_read_altstatus,
+	.write_devctl		= via_write_devctl,
+
+	.dev_select		= via_dev_select,
+	.tf_load		= via_tf_load,
+	.tf_read		= ide_tf_read,
+
+	.input_data		= ide_input_data,
+	.output_data		= ide_output_data,
+};
+
 static const struct ide_port_info via82cxxx_chipset __devinitdata = {
 	.name		= DRV_NAME,
 	.init_chipset	= init_chipset_via82cxxx,
 	.enablebits	= { { 0x40, 0x02, 0x02 }, { 0x40, 0x01, 0x01 } },
+	.tp_ops		= &via_tp_ops,
 	.port_ops	= &via_port_ops,
 	.host_flags	= IDE_HFLAG_PIO_NO_BLACKLIST |
 			  IDE_HFLAG_POST_SET_MODE |
@@ -402,11 +487,6 @@
 	 * Find the ISA bridge and check we know what it is.
 	 */
 	via_config = via_config_find(&isa);
-	if (!via_config->id) {
-		printk(KERN_WARNING DRV_NAME " %s: unknown chipset, skipping\n",
-			pci_name(dev));
-		return -ENODEV;
-	}
 
 	/*
 	 * Print the boot message.
@@ -436,10 +516,13 @@
 		via_clock = 33333;
 	}
 
-	if (idx == 0)
-		d.host_flags |= IDE_HFLAG_NO_AUTODMA;
-	else
+	if (idx == 1)
 		d.enablebits[1].reg = d.enablebits[0].reg = 0;
+	else
+		d.host_flags |= IDE_HFLAG_NO_AUTODMA;
+
+	if (idx == VIA_IDFLAG_SINGLE)
+		d.host_flags |= IDE_HFLAG_SINGLE;
 
 	if ((via_config->flags & VIA_NO_UNMASK) == 0)
 		d.host_flags |= IDE_HFLAG_UNMASK_IRQS;
@@ -475,8 +558,9 @@
 	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C576_1),  0 },
 	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_82C586_1),  0 },
 	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_CX700_IDE), 0 },
-	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_VX855_IDE), 0 },
+	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_VX855_IDE), VIA_IDFLAG_SINGLE },
 	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_6410),      1 },
+	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_6415),      1 },
 	{ PCI_VDEVICE(VIA, PCI_DEVICE_ID_VIA_SATA_EIDE), 1 },
 	{ 0, },
 };
@@ -504,6 +588,6 @@
 module_init(via_ide_init);
 module_exit(via_ide_exit);
 
-MODULE_AUTHOR("Vojtech Pavlik, Michel Aubry, Jeff Garzik, Andre Hedrick");
+MODULE_AUTHOR("Vojtech Pavlik, Bartlomiej Zolnierkiewicz, Michel Aubry, Jeff Garzik, Andre Hedrick");
 MODULE_DESCRIPTION("PCI driver module for VIA IDE");
 MODULE_LICENSE("GPL");
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 0ec6129..97e6ab4 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -515,6 +515,8 @@
         u8	init_speed;	/* transfer rate set at boot */
         u8	current_speed;	/* current transfer rate set */
 	u8	desired_speed;	/* desired transfer rate set */
+	u8	pio_mode;	/* for ->set_pio_mode _only_ */
+	u8	dma_mode;	/* for ->dma_pio_mode _only_ */
         u8	dn;		/* now wide spread use */
 	u8	acoustic;	/* acoustic management */
 	u8	media;		/* disk, cdrom, tape, floppy, ... */
@@ -622,8 +624,8 @@
  */
 struct ide_port_ops {
 	void	(*init_dev)(ide_drive_t *);
-	void	(*set_pio_mode)(ide_drive_t *, const u8);
-	void	(*set_dma_mode)(ide_drive_t *, const u8);
+	void	(*set_pio_mode)(struct hwif_s *, ide_drive_t *);
+	void	(*set_dma_mode)(struct hwif_s *, ide_drive_t *);
 	int	(*reset_poll)(ide_drive_t *);
 	void	(*pre_reset)(ide_drive_t *);
 	void	(*resetproc)(ide_drive_t *);
@@ -1494,7 +1496,6 @@
 #ifdef CONFIG_IDE_XFER_MODE
 int ide_scan_pio_blacklist(char *);
 const char *ide_xfer_verbose(u8);
-u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
 int ide_pio_need_iordy(ide_drive_t *, const u8);
 int ide_set_pio_mode(ide_drive_t *, u8);
 int ide_set_dma_mode(ide_drive_t *, u8);