ath9k: use ath_hw for DPRINTF() and debug init/exit
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index 52bed89..68d8dd9 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -224,7 +224,7 @@
}
sband->n_bitrates++;
- DPRINTF(sc, ATH_DBG_CONFIG, "Rate: %2dMbps, ratecode: %2d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Rate: %2dMbps, ratecode: %2d\n",
rate[i].bitrate / 10, rate[i].hw_value);
}
}
@@ -280,7 +280,7 @@
if (!stopped || (sc->sc_flags & SC_OP_FULL_RESET))
fastcc = false;
- DPRINTF(sc, ATH_DBG_CONFIG,
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG,
"(%u MHz) -> (%u MHz), chanwidth: %d\n",
sc->sc_ah->curchan->channel,
channel->center_freq, sc->tx_chan_width);
@@ -289,7 +289,7 @@
r = ath9k_hw_reset(ah, hchan, fastcc);
if (r) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to reset channel (%u Mhz) "
"reset status %d\n",
channel->center_freq, r);
@@ -301,7 +301,7 @@
sc->sc_flags &= ~SC_OP_FULL_RESET;
if (ath_startrecv(sc) != 0) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to restart recv logic\n");
r = -EIO;
goto ps_restore;
@@ -353,7 +353,7 @@
/* Long calibration runs independently of short calibration. */
if ((timestamp - sc->ani.longcal_timer) >= ATH_LONG_CALINTERVAL) {
longcal = true;
- DPRINTF(sc, ATH_DBG_ANI, "longcal @%lu\n", jiffies);
+ DPRINTF(sc->sc_ah, ATH_DBG_ANI, "longcal @%lu\n", jiffies);
sc->ani.longcal_timer = timestamp;
}
@@ -361,7 +361,7 @@
if (!sc->ani.caldone) {
if ((timestamp - sc->ani.shortcal_timer) >= short_cal_interval) {
shortcal = true;
- DPRINTF(sc, ATH_DBG_ANI, "shortcal @%lu\n", jiffies);
+ DPRINTF(sc->sc_ah, ATH_DBG_ANI, "shortcal @%lu\n", jiffies);
sc->ani.shortcal_timer = timestamp;
sc->ani.resetcal_timer = timestamp;
}
@@ -395,7 +395,7 @@
sc->ani.noise_floor = ath9k_hw_getchan_noise(ah,
ah->curchan);
- DPRINTF(sc, ATH_DBG_ANI," calibrate chan %u/%x nf: %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_ANI," calibrate chan %u/%x nf: %d\n",
ah->curchan->channel, ah->curchan->channelFlags,
sc->ani.noise_floor);
}
@@ -448,7 +448,7 @@
sc->rx_chainmask = 1;
}
- DPRINTF(sc, ATH_DBG_CONFIG, "tx chmask: %d, rx chmask: %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "tx chmask: %d, rx chmask: %d\n",
sc->tx_chainmask, sc->rx_chainmask);
}
@@ -502,7 +502,7 @@
* TSF sync does not look correct; remain awake to sync with
* the next Beacon.
*/
- DPRINTF(sc, ATH_DBG_PS, "TSFOOR - Sync with next Beacon\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_PS, "TSFOOR - Sync with next Beacon\n");
sc->sc_flags |= SC_OP_WAIT_FOR_BEACON | SC_OP_BEACON_SYNC;
}
@@ -702,7 +702,7 @@
memcpy(hk->kv_mic, key_txmic, sizeof(hk->kv_mic));
if (!ath9k_hw_set_keycache_entry(sc->sc_ah, keyix, hk, NULL)) {
/* TX MIC entry failed. No need to proceed further */
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Setting TX MIC Key Failed\n");
return 0;
}
@@ -907,7 +907,7 @@
rx_streams = !(sc->rx_chainmask & (sc->rx_chainmask - 1)) ? 1 : 2;
if (tx_streams != rx_streams) {
- DPRINTF(sc, ATH_DBG_CONFIG, "TX streams %d, RX streams: %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "TX streams %d, RX streams: %d\n",
tx_streams, rx_streams);
ht_info->mcs.tx_params |= IEEE80211_HT_MCS_TX_RX_DIFF;
ht_info->mcs.tx_params |= ((tx_streams - 1) <<
@@ -927,7 +927,7 @@
{
if (bss_conf->assoc) {
- DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info ASSOC %d, bssid: %pM\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Bss Info ASSOC %d, bssid: %pM\n",
bss_conf->aid, sc->curbssid);
/* New association, store aid */
@@ -949,7 +949,7 @@
ath_start_ani(sc);
} else {
- DPRINTF(sc, ATH_DBG_CONFIG, "Bss Info DISASSOC\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Bss Info DISASSOC\n");
sc->curaid = 0;
/* Stop ANI */
del_timer_sync(&sc->ani.timer);
@@ -1042,7 +1042,7 @@
ret = led_classdev_register(wiphy_dev(sc->hw->wiphy), &led->led_cdev);
if (ret)
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Failed to register led:%s", led->name);
else
led->registered = 1;
@@ -1139,7 +1139,7 @@
spin_lock_bh(&sc->sc_resetlock);
r = ath9k_hw_reset(ah, ah->curchan, false);
if (r) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to reset channel %u (%uMhz) ",
"reset status %d\n",
channel->center_freq, r);
@@ -1148,7 +1148,7 @@
ath_update_txpow(sc);
if (ath_startrecv(sc) != 0) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to restart recv logic\n");
return;
}
@@ -1194,7 +1194,7 @@
spin_lock_bh(&sc->sc_resetlock);
r = ath9k_hw_reset(ah, ah->curchan, false);
if (r) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to reset channel %u (%uMhz) "
"reset status %d\n",
channel->center_freq, r);
@@ -1248,11 +1248,12 @@
void ath_detach(struct ath_softc *sc)
{
struct ieee80211_hw *hw = sc->hw;
+ struct ath_hw *ah = sc->sc_ah;
int i = 0;
ath9k_ps_wakeup(sc);
- DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n");
+ dev_dbg(sc->dev, "Detach ATH hw\n");
ath_deinit_leds(sc);
wiphy_rfkill_stop_polling(sc->hw->wiphy);
@@ -1273,7 +1274,7 @@
tasklet_kill(&sc->bcon_tasklet);
if (!(sc->sc_flags & SC_OP_INVALID))
- ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_AWAKE);
+ ath9k_hw_setpower(ah, ATH9K_PM_AWAKE);
/* cleanup tx queues */
for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++)
@@ -1282,11 +1283,11 @@
if ((sc->btcoex_info.no_stomp_timer) &&
sc->btcoex_info.btcoex_scheme == ATH_BTCOEX_CFG_3WIRE)
- ath_gen_timer_free(sc->sc_ah, sc->btcoex_info.no_stomp_timer);
+ ath_gen_timer_free(ah, sc->btcoex_info.no_stomp_timer);
- ath9k_hw_detach(sc->sc_ah);
+ ath9k_hw_detach(ah);
+ ath9k_exit_debug(sc->sc_ah);
sc->sc_ah = NULL;
- ath9k_exit_debug(sc);
}
static int ath9k_reg_notifier(struct wiphy *wiphy,
@@ -1315,9 +1316,6 @@
/* XXX: hardware will not be ready until ath_open() being called */
sc->sc_flags |= SC_OP_INVALID;
- if (ath9k_init_debug(sc) < 0)
- printk(KERN_ERR "Unable to create debugfs files\n");
-
spin_lock_init(&sc->wiphy_lock);
spin_lock_init(&sc->sc_resetlock);
spin_lock_init(&sc->sc_serial_rw);
@@ -1347,9 +1345,12 @@
ah->hw_version.subsysid = subsysid;
sc->sc_ah = ah;
+ if (ath9k_init_debug(ah) < 0)
+ dev_err(sc->dev, "Unable to create debugfs files\n");
+
r = ath9k_hw_init(ah);
if (r) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to initialize hardware; "
"initialization status: %d\n", r);
goto bad;
@@ -1358,7 +1359,7 @@
/* Get the hardware key cache size. */
sc->keymax = ah->caps.keycache_size;
if (sc->keymax > ATH_KEYMAX) {
- DPRINTF(sc, ATH_DBG_ANY,
+ DPRINTF(ah, ATH_DBG_ANY,
"Warning, using only %u entries in %u key cache\n",
ATH_KEYMAX, sc->keymax);
sc->keymax = ATH_KEYMAX;
@@ -1388,14 +1389,14 @@
*/
sc->beacon.beaconq = ath_beaconq_setup(ah);
if (sc->beacon.beaconq == -1) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup a beacon xmit queue\n");
r = -EIO;
goto bad2;
}
sc->beacon.cabq = ath_txq_setup(sc, ATH9K_TX_QUEUE_CAB, 0);
if (sc->beacon.cabq == NULL) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup CAB xmit queue\n");
r = -EIO;
goto bad2;
@@ -1410,26 +1411,26 @@
/* Setup data queues */
/* NB: ensure BK queue is the lowest priority h/w queue */
if (!ath_tx_setup(sc, ATH9K_WME_AC_BK)) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup xmit queue for BK traffic\n");
r = -EIO;
goto bad2;
}
if (!ath_tx_setup(sc, ATH9K_WME_AC_BE)) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup xmit queue for BE traffic\n");
r = -EIO;
goto bad2;
}
if (!ath_tx_setup(sc, ATH9K_WME_AC_VI)) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup xmit queue for VI traffic\n");
r = -EIO;
goto bad2;
}
if (!ath_tx_setup(sc, ATH9K_WME_AC_VO)) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to setup xmit queue for VO traffic\n");
r = -EIO;
goto bad2;
@@ -1529,9 +1530,9 @@
ath_tx_cleanupq(sc, &sc->tx.txq[i]);
bad:
ath9k_hw_detach(ah);
- sc->sc_ah = NULL;
bad_no_ah:
- ath9k_exit_debug(sc);
+ ath9k_exit_debug(sc->sc_ah);
+ sc->sc_ah = NULL;
return r;
}
@@ -1577,18 +1578,21 @@
int ath_init_device(u16 devid, struct ath_softc *sc, u16 subsysid)
{
struct ieee80211_hw *hw = sc->hw;
+ struct ath_hw *ah;
int error = 0, i;
struct ath_regulatory *reg;
- DPRINTF(sc, ATH_DBG_CONFIG, "Attach ATH hw\n");
+ dev_dbg(sc->dev, "Attach ATH hw\n");
error = ath_init_softc(devid, sc, subsysid);
if (error != 0)
return error;
+ ah = sc->sc_ah;
+
/* get mac address from hardware and set in mac80211 */
- SET_IEEE80211_PERM_ADDR(hw, sc->sc_ah->macaddr);
+ SET_IEEE80211_PERM_ADDR(hw, ah->macaddr);
ath_set_hw_capab(sc, hw);
@@ -1599,9 +1603,9 @@
reg = &sc->common.regulatory;
- if (sc->sc_ah->caps.hw_caps & ATH9K_HW_CAP_HT) {
+ if (ah->caps.hw_caps & ATH9K_HW_CAP_HT) {
setup_ht_cap(sc, &sc->sbands[IEEE80211_BAND_2GHZ].ht_cap);
- if (test_bit(ATH9K_MODE_11A, sc->sc_ah->caps.wireless_modes))
+ if (test_bit(ATH9K_MODE_11A, ah->caps.wireless_modes))
setup_ht_cap(sc, &sc->sbands[IEEE80211_BAND_5GHZ].ht_cap);
}
@@ -1639,9 +1643,9 @@
if (ATH_TXQ_SETUP(sc, i))
ath_tx_cleanupq(sc, &sc->tx.txq[i]);
- ath9k_hw_detach(sc->sc_ah);
+ ath9k_hw_detach(ah);
+ ath9k_exit_debug(ah);
sc->sc_ah = NULL;
- ath9k_exit_debug(sc);
return error;
}
@@ -1660,12 +1664,12 @@
spin_lock_bh(&sc->sc_resetlock);
r = ath9k_hw_reset(ah, sc->sc_ah->curchan, false);
if (r)
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(ah, ATH_DBG_FATAL,
"Unable to reset hardware; reset status %d\n", r);
spin_unlock_bh(&sc->sc_resetlock);
if (ath_startrecv(sc) != 0)
- DPRINTF(sc, ATH_DBG_FATAL, "Unable to start recv logic\n");
+ DPRINTF(ah, ATH_DBG_FATAL, "Unable to start recv logic\n");
/*
* We may be doing a reset in response to a request
@@ -1713,13 +1717,13 @@
struct ath_buf *bf;
int i, bsize, error;
- DPRINTF(sc, ATH_DBG_CONFIG, "%s DMA: %u buffers %u desc/buf\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "%s DMA: %u buffers %u desc/buf\n",
name, nbuf, ndesc);
INIT_LIST_HEAD(head);
/* ath_desc must be a multiple of DWORDs */
if ((sizeof(struct ath_desc) % 4) != 0) {
- DPRINTF(sc, ATH_DBG_FATAL, "ath_desc not DWORD aligned\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL, "ath_desc not DWORD aligned\n");
ASSERT((sizeof(struct ath_desc) % 4) == 0);
error = -ENOMEM;
goto fail;
@@ -1753,7 +1757,7 @@
goto fail;
}
ds = dd->dd_desc;
- DPRINTF(sc, ATH_DBG_CONFIG, "%s DMA map: %p (%u) -> %llx (%u)\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "%s DMA map: %p (%u) -> %llx (%u)\n",
name, ds, (u32) dd->dd_desc_len,
ito64(dd->dd_desc_paddr), /*XXX*/(u32) dd->dd_desc_len);
@@ -1905,7 +1909,7 @@
struct ath9k_channel *init_channel;
int r;
- DPRINTF(sc, ATH_DBG_CONFIG, "Starting driver with "
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Starting driver with "
"initial channel: %d MHz\n", curchan->center_freq);
mutex_lock(&sc->mutex);
@@ -1950,7 +1954,7 @@
spin_lock_bh(&sc->sc_resetlock);
r = ath9k_hw_reset(sc->sc_ah, init_channel, false);
if (r) {
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Unable to reset hardware; reset status %d "
"(freq %u MHz)\n", r,
curchan->center_freq);
@@ -1973,7 +1977,7 @@
* here except setup the interrupt mask.
*/
if (ath_startrecv(sc) != 0) {
- DPRINTF(sc, ATH_DBG_FATAL, "Unable to start recv logic\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL, "Unable to start recv logic\n");
r = -EIO;
goto mutex_unlock;
}
@@ -2042,7 +2046,7 @@
if (ieee80211_is_data(hdr->frame_control) &&
!ieee80211_is_nullfunc(hdr->frame_control) &&
!ieee80211_has_pm(hdr->frame_control)) {
- DPRINTF(sc, ATH_DBG_PS, "Add PM=1 for a TX frame "
+ DPRINTF(sc->sc_ah, ATH_DBG_PS, "Add PM=1 for a TX frame "
"while in PS mode\n");
hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_PM);
}
@@ -2058,11 +2062,11 @@
ath9k_ps_wakeup(sc);
ath9k_hw_setrxabort(sc->sc_ah, 0);
if (ieee80211_is_pspoll(hdr->frame_control)) {
- DPRINTF(sc, ATH_DBG_PS, "Sending PS-Poll to pick a "
+ DPRINTF(sc->sc_ah, ATH_DBG_PS, "Sending PS-Poll to pick a "
"buffered frame\n");
sc->sc_flags |= SC_OP_WAIT_FOR_PSPOLL_DATA;
} else {
- DPRINTF(sc, ATH_DBG_PS, "Wake up to complete TX\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_PS, "Wake up to complete TX\n");
sc->sc_flags |= SC_OP_WAIT_FOR_TX_ACK;
}
/*
@@ -2104,10 +2108,10 @@
if (!txctl.txq)
goto exit;
- DPRINTF(sc, ATH_DBG_XMIT, "transmitting packet, skb: %p\n", skb);
+ DPRINTF(sc->sc_ah, ATH_DBG_XMIT, "transmitting packet, skb: %p\n", skb);
if (ath_tx_start(hw, skb, &txctl) != 0) {
- DPRINTF(sc, ATH_DBG_XMIT, "TX failed\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_XMIT, "TX failed\n");
goto exit;
}
@@ -2135,7 +2139,7 @@
}
if (sc->sc_flags & SC_OP_INVALID) {
- DPRINTF(sc, ATH_DBG_ANY, "Device not present\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_ANY, "Device not present\n");
mutex_unlock(&sc->mutex);
return;
}
@@ -2171,7 +2175,7 @@
mutex_unlock(&sc->mutex);
- DPRINTF(sc, ATH_DBG_CONFIG, "Driver halt\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Driver halt\n");
}
static int ath9k_add_interface(struct ieee80211_hw *hw,
@@ -2205,13 +2209,13 @@
ic_opmode = conf->type;
break;
default:
- DPRINTF(sc, ATH_DBG_FATAL,
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL,
"Interface type %d not yet supported\n", conf->type);
ret = -EOPNOTSUPP;
goto out;
}
- DPRINTF(sc, ATH_DBG_CONFIG, "Attach a VIF of type: %d\n", ic_opmode);
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Attach a VIF of type: %d\n", ic_opmode);
/* Set the VIF opmode */
avp->av_opmode = ic_opmode;
@@ -2264,7 +2268,7 @@
struct ath_vif *avp = (void *)conf->vif->drv_priv;
int i;
- DPRINTF(sc, ATH_DBG_CONFIG, "Detach Interface\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Detach Interface\n");
mutex_lock(&sc->mutex);
@@ -2318,7 +2322,7 @@
}
else if (all_wiphys_idle) {
ath_radio_enable(sc);
- DPRINTF(sc, ATH_DBG_CONFIG,
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG,
"not-idle: enabling radio\n");
}
}
@@ -2372,7 +2376,7 @@
goto skip_chan_change;
}
- DPRINTF(sc, ATH_DBG_CONFIG, "Set channel: %d MHz\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Set channel: %d MHz\n",
curchan->center_freq);
/* XXX: remove me eventualy */
@@ -2381,7 +2385,7 @@
ath_update_chainmask(sc, conf_is_ht(conf));
if (ath_set_channel(sc, hw, &sc->sc_ah->channels[pos]) < 0) {
- DPRINTF(sc, ATH_DBG_FATAL, "Unable to set channel\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL, "Unable to set channel\n");
mutex_unlock(&sc->mutex);
return -EINVAL;
}
@@ -2392,7 +2396,7 @@
sc->config.txpowlimit = 2 * conf->power_level;
if (disable_radio) {
- DPRINTF(sc, ATH_DBG_CONFIG, "idle: disabling radio\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "idle: disabling radio\n");
ath_radio_disable(sc);
}
@@ -2429,7 +2433,7 @@
ath9k_hw_setrxfilter(sc->sc_ah, rfilt);
ath9k_ps_restore(sc);
- DPRINTF(sc, ATH_DBG_CONFIG, "Set HW RX filter: 0x%x\n", rfilt);
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Set HW RX filter: 0x%x\n", rfilt);
}
static void ath9k_sta_notify(struct ieee80211_hw *hw,
@@ -2473,7 +2477,7 @@
qi.tqi_burstTime = params->txop;
qnum = ath_get_hal_qnum(queue, sc);
- DPRINTF(sc, ATH_DBG_CONFIG,
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG,
"Configure tx [queue/halq] [%d/%d], "
"aifs: %d, cw_min: %d, cw_max: %d, txop: %d\n",
queue, qnum, params->aifs, params->cw_min,
@@ -2481,7 +2485,7 @@
ret = ath_txq_update(sc, qnum, &qi);
if (ret)
- DPRINTF(sc, ATH_DBG_FATAL, "TXQ Update failed\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL, "TXQ Update failed\n");
mutex_unlock(&sc->mutex);
@@ -2503,7 +2507,7 @@
mutex_lock(&sc->mutex);
ath9k_ps_wakeup(sc);
- DPRINTF(sc, ATH_DBG_CONFIG, "Set HW Key\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "Set HW Key\n");
switch (cmd) {
case SET_KEY:
@@ -2577,7 +2581,7 @@
/* Set aggregation protection mode parameters */
sc->config.ath_aggr_prot = 0;
- DPRINTF(sc, ATH_DBG_CONFIG,
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG,
"RX filter 0x%x bssid %pM aid 0x%x\n",
rfilt, sc->curbssid, sc->curaid);
@@ -2626,7 +2630,7 @@
ath_update_chainmask(sc, 0);
if (changed & BSS_CHANGED_ERP_PREAMBLE) {
- DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed PREAMBLE %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "BSS Changed PREAMBLE %d\n",
bss_conf->use_short_preamble);
if (bss_conf->use_short_preamble)
sc->sc_flags |= SC_OP_PREAMBLE_SHORT;
@@ -2635,7 +2639,7 @@
}
if (changed & BSS_CHANGED_ERP_CTS_PROT) {
- DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed CTS PROT %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "BSS Changed CTS PROT %d\n",
bss_conf->use_cts_prot);
if (bss_conf->use_cts_prot &&
hw->conf.channel->band != IEEE80211_BAND_5GHZ)
@@ -2645,7 +2649,7 @@
}
if (changed & BSS_CHANGED_ASSOC) {
- DPRINTF(sc, ATH_DBG_CONFIG, "BSS Changed ASSOC %d\n",
+ DPRINTF(sc->sc_ah, ATH_DBG_CONFIG, "BSS Changed ASSOC %d\n",
bss_conf->assoc);
ath9k_bss_assoc_info(sc, vif, bss_conf);
}
@@ -2726,7 +2730,7 @@
ath_tx_aggr_resume(sc, sta, tid);
break;
default:
- DPRINTF(sc, ATH_DBG_FATAL, "Unknown AMPDU action\n");
+ DPRINTF(sc->sc_ah, ATH_DBG_FATAL, "Unknown AMPDU action\n");
}
return ret;