Pull thermal into release branch
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 17770b4..b41cde3 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1823,6 +1823,10 @@
-1: disable all active trip points in all thermal zones
<degrees C>: override all lowest active trip points
+ thermal.crt= [HW,ACPI]
+ -1: disable all critical trip points in all thermal zones
+ <degrees C>: lower all critical trip points
+
thermal.nocrt= [HW,ACPI]
Set to disable actions on ACPI thermal zone
critical and hot trip points.
diff --git a/drivers/acpi/thermal.c b/drivers/acpi/thermal.c
index 1e06159..7e8f48b 100644
--- a/drivers/acpi/thermal.c
+++ b/drivers/acpi/thermal.c
@@ -77,23 +77,27 @@
static int act;
module_param(act, int, 0644);
-MODULE_PARM_DESC(act, "Disable or override all lowest active trip points.\n");
+MODULE_PARM_DESC(act, "Disable or override all lowest active trip points.");
+
+static int crt;
+module_param(crt, int, 0644);
+MODULE_PARM_DESC(crt, "Disable or lower all critical trip points.");
static int tzp;
module_param(tzp, int, 0444);
-MODULE_PARM_DESC(tzp, "Thermal zone polling frequency, in 1/10 seconds.\n");
+MODULE_PARM_DESC(tzp, "Thermal zone polling frequency, in 1/10 seconds.");
static int nocrt;
module_param(nocrt, int, 0);
-MODULE_PARM_DESC(nocrt, "Set to disable action on ACPI thermal zone critical and hot trips.\n");
+MODULE_PARM_DESC(nocrt, "Set to take no action upon ACPI thermal zone critical trips points.");
static int off;
module_param(off, int, 0);
-MODULE_PARM_DESC(off, "Set to disable ACPI thermal support.\n");
+MODULE_PARM_DESC(off, "Set to disable ACPI thermal support.");
static int psv;
module_param(psv, int, 0644);
-MODULE_PARM_DESC(psv, "Disable or override all passive trip points.\n");
+MODULE_PARM_DESC(psv, "Disable or override all passive trip points.");
static int acpi_thermal_add(struct acpi_device *device);
static int acpi_thermal_remove(struct acpi_device *device, int type);
@@ -340,6 +344,20 @@
tz->trips.critical.temperature));
}
+ if (tz->trips.critical.flags.valid == 1) {
+ if (crt == -1) {
+ tz->trips.critical.flags.valid = 0;
+ } else if (crt > 0) {
+ unsigned long crt_k = CELSIUS_TO_KELVIN(crt);
+
+ /*
+ * Allow override to lower critical threshold
+ */
+ if (crt_k < tz->trips.critical.temperature)
+ tz->trips.critical.temperature = crt_k;
+ }
+ }
+
/* Critical Sleep (optional) */
status =
@@ -1067,9 +1085,9 @@
entry->owner = THIS_MODULE;
}
- /* 'trip_points' [R/W] */
+ /* 'trip_points' [R] */
entry = create_proc_entry(ACPI_THERMAL_FILE_TRIP_POINTS,
- S_IFREG | S_IRUGO | S_IWUSR,
+ S_IRUGO,
acpi_device_dir(device));
if (!entry)
return -ENODEV;
@@ -1339,6 +1357,13 @@
}
return 0;
}
+static int thermal_nocrt(struct dmi_system_id *d) {
+
+ printk(KERN_NOTICE "ACPI: %s detected: "
+ "disabling all critical thermal trip point actions.\n", d->ident);
+ nocrt = 1;
+ return 0;
+}
static int thermal_tzp(struct dmi_system_id *d) {
if (tzp == 0) {
@@ -1387,6 +1412,14 @@
DMI_MATCH(DMI_BOARD_NAME, "i915GMm-HFS"),
},
},
+ {
+ .callback = thermal_nocrt,
+ .ident = "Gigabyte GA-7ZX",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co., Ltd."),
+ DMI_MATCH(DMI_BOARD_NAME, "7ZX"),
+ },
+ },
{}
};
#endif /* CONFIG_DMI */