| /* |
| * Copyright 2011 Analog Devices Inc. |
| * |
| * Licensed under the GPL-2. |
| * |
| */ |
| |
| #include <linux/interrupt.h> |
| #include <linux/gpio.h> |
| #include <linux/device.h> |
| #include <linux/kernel.h> |
| #include <linux/slab.h> |
| |
| #include "../iio.h" |
| #include "../buffer.h" |
| #include "../ring_sw.h" |
| #include "../trigger_consumer.h" |
| |
| #include "ad7606.h" |
| |
| /** |
| * ad7606_trigger_handler_th() th/bh of trigger launched polling to ring buffer |
| * |
| **/ |
| static irqreturn_t ad7606_trigger_handler_th_bh(int irq, void *p) |
| { |
| struct iio_poll_func *pf = p; |
| struct ad7606_state *st = iio_priv(pf->indio_dev); |
| |
| gpio_set_value(st->pdata->gpio_convst, 1); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * ad7606_poll_bh_to_ring() bh of trigger launched polling to ring buffer |
| * @work_s: the work struct through which this was scheduled |
| * |
| * Currently there is no option in this driver to disable the saving of |
| * timestamps within the ring. |
| * I think the one copy of this at a time was to avoid problems if the |
| * trigger was set far too high and the reads then locked up the computer. |
| **/ |
| static void ad7606_poll_bh_to_ring(struct work_struct *work_s) |
| { |
| struct ad7606_state *st = container_of(work_s, struct ad7606_state, |
| poll_work); |
| struct iio_dev *indio_dev = iio_priv_to_dev(st); |
| struct iio_buffer *ring = indio_dev->buffer; |
| s64 time_ns; |
| __u8 *buf; |
| int ret; |
| |
| buf = kzalloc(ring->access->get_bytes_per_datum(ring), |
| GFP_KERNEL); |
| if (buf == NULL) |
| return; |
| |
| if (gpio_is_valid(st->pdata->gpio_frstdata)) { |
| ret = st->bops->read_block(st->dev, 1, buf); |
| if (ret) |
| goto done; |
| if (!gpio_get_value(st->pdata->gpio_frstdata)) { |
| /* This should never happen. However |
| * some signal glitch caused by bad PCB desgin or |
| * electrostatic discharge, could cause an extra read |
| * or clock. This allows recovery. |
| */ |
| ad7606_reset(st); |
| goto done; |
| } |
| ret = st->bops->read_block(st->dev, |
| st->chip_info->num_channels - 1, buf + 2); |
| if (ret) |
| goto done; |
| } else { |
| ret = st->bops->read_block(st->dev, |
| st->chip_info->num_channels, buf); |
| if (ret) |
| goto done; |
| } |
| |
| time_ns = iio_get_time_ns(); |
| |
| if (ring->scan_timestamp) |
| *((s64 *)(buf + ring->access->get_bytes_per_datum(ring) - |
| sizeof(s64))) = time_ns; |
| |
| ring->access->store_to(indio_dev->buffer, buf, time_ns); |
| done: |
| gpio_set_value(st->pdata->gpio_convst, 0); |
| iio_trigger_notify_done(indio_dev->trig); |
| kfree(buf); |
| } |
| |
| static const struct iio_buffer_setup_ops ad7606_ring_setup_ops = { |
| .preenable = &iio_sw_buffer_preenable, |
| .postenable = &iio_triggered_buffer_postenable, |
| .predisable = &iio_triggered_buffer_predisable, |
| }; |
| |
| int ad7606_register_ring_funcs_and_init(struct iio_dev *indio_dev) |
| { |
| struct ad7606_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| indio_dev->buffer = iio_sw_rb_allocate(indio_dev); |
| if (!indio_dev->buffer) { |
| ret = -ENOMEM; |
| goto error_ret; |
| } |
| |
| indio_dev->pollfunc = iio_alloc_pollfunc(&ad7606_trigger_handler_th_bh, |
| &ad7606_trigger_handler_th_bh, |
| 0, |
| indio_dev, |
| "%s_consumer%d", |
| indio_dev->name, |
| indio_dev->id); |
| if (indio_dev->pollfunc == NULL) { |
| ret = -ENOMEM; |
| goto error_deallocate_sw_rb; |
| } |
| |
| /* Ring buffer functions - here trigger setup related */ |
| |
| indio_dev->setup_ops = &ad7606_ring_setup_ops; |
| indio_dev->buffer->scan_timestamp = true ; |
| |
| INIT_WORK(&st->poll_work, &ad7606_poll_bh_to_ring); |
| |
| /* Flag that polled ring buffering is possible */ |
| indio_dev->modes |= INDIO_BUFFER_TRIGGERED; |
| return 0; |
| |
| error_deallocate_sw_rb: |
| iio_sw_rb_free(indio_dev->buffer); |
| error_ret: |
| return ret; |
| } |
| |
| void ad7606_ring_cleanup(struct iio_dev *indio_dev) |
| { |
| iio_dealloc_pollfunc(indio_dev->pollfunc); |
| iio_sw_rb_free(indio_dev->buffer); |
| } |