e1000: Add support for the CE4100 reference platform
This patch adds support for the gigabit phys present on the CE4100 reference
platforms.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index ecd9f6c..f5514a0 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -52,6 +52,7 @@
e1000_82545,
e1000_82545_rev_3,
e1000_82546,
+ e1000_ce4100,
e1000_82546_rev_3,
e1000_82541,
e1000_82541_rev_2,
@@ -209,9 +210,11 @@
} e1000_1000t_rx_status;
typedef enum {
- e1000_phy_m88 = 0,
- e1000_phy_igp,
- e1000_phy_undefined = 0xFF
+ e1000_phy_m88 = 0,
+ e1000_phy_igp,
+ e1000_phy_8211,
+ e1000_phy_8201,
+ e1000_phy_undefined = 0xFF
} e1000_phy_type;
typedef enum {
@@ -442,6 +445,7 @@
#define E1000_DEV_ID_82547EI 0x1019
#define E1000_DEV_ID_82547EI_MOBILE 0x101A
#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
+#define E1000_DEV_ID_INTEL_CE4100_GBE 0x2E6E
#define NODE_ADDRESS_SIZE 6
#define ETH_LENGTH_OF_ADDRESS 6
@@ -808,6 +812,16 @@
#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
#define E1000_FLA 0x0001C /* Flash Access - RW */
#define E1000_MDIC 0x00020 /* MDI Control - RW */
+
+extern void __iomem *ce4100_gbe_mdio_base_virt;
+#define INTEL_CE_GBE_MDIO_RCOMP_BASE (ce4100_gbe_mdio_base_virt)
+#define E1000_MDIO_STS (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0)
+#define E1000_MDIO_CMD (INTEL_CE_GBE_MDIO_RCOMP_BASE + 4)
+#define E1000_MDIO_DRV (INTEL_CE_GBE_MDIO_RCOMP_BASE + 8)
+#define E1000_MDC_CMD (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0xC)
+#define E1000_RCOMP_CTL (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0x20)
+#define E1000_RCOMP_STS (INTEL_CE_GBE_MDIO_RCOMP_BASE + 0x24)
+
#define E1000_SCTL 0x00024 /* SerDes Control - RW */
#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
@@ -820,6 +834,34 @@
#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
+
+/* Auxiliary Control Register. This register is CE4100 specific,
+ * RMII/RGMII function is switched by this register - RW
+ * Following are bits definitions of the Auxiliary Control Register
+ */
+#define E1000_CTL_AUX 0x000E0
+#define E1000_CTL_AUX_END_SEL_SHIFT 10
+#define E1000_CTL_AUX_ENDIANESS_SHIFT 8
+#define E1000_CTL_AUX_RGMII_RMII_SHIFT 0
+
+/* descriptor and packet transfer use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_DES_PKT (0x0 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* descriptor use CTL_AUX.ENDIANESS, packet use default */
+#define E1000_CTL_AUX_DES (0x1 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* descriptor use default, packet use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_PKT (0x2 << E1000_CTL_AUX_END_SEL_SHIFT)
+/* all use CTL_AUX.ENDIANESS */
+#define E1000_CTL_AUX_ALL (0x3 << E1000_CTL_AUX_END_SEL_SHIFT)
+
+#define E1000_CTL_AUX_RGMII (0x0 << E1000_CTL_AUX_RGMII_RMII_SHIFT)
+#define E1000_CTL_AUX_RMII (0x1 << E1000_CTL_AUX_RGMII_RMII_SHIFT)
+
+/* LW little endian, Byte big endian */
+#define E1000_CTL_AUX_LWLE_BBE (0x0 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWLE_BLE (0x1 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWBE_BBE (0x2 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+#define E1000_CTL_AUX_LWBE_BLE (0x3 << E1000_CTL_AUX_ENDIANESS_SHIFT)
+
#define E1000_RCTL 0x00100 /* RX Control - RW */
#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
@@ -1011,6 +1053,7 @@
* in more current versions of the 8254x. Despite the difference in location,
* the registers function in the same manner.
*/
+#define E1000_82542_CTL_AUX E1000_CTL_AUX
#define E1000_82542_CTRL E1000_CTRL
#define E1000_82542_CTRL_DUP E1000_CTRL_DUP
#define E1000_82542_STATUS E1000_STATUS
@@ -1571,6 +1614,11 @@
#define E1000_MDIC_INT_EN 0x20000000
#define E1000_MDIC_ERROR 0x40000000
+#define INTEL_CE_GBE_MDIC_OP_WRITE 0x04000000
+#define INTEL_CE_GBE_MDIC_OP_READ 0x00000000
+#define INTEL_CE_GBE_MDIC_GO 0x80000000
+#define INTEL_CE_GBE_MDIC_READ_ERROR 0x80000000
+
#define E1000_KUMCTRLSTA_MASK 0x0000FFFF
#define E1000_KUMCTRLSTA_OFFSET 0x001F0000
#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16
@@ -2871,6 +2919,11 @@
#define M88E1111_I_PHY_ID 0x01410CC0
#define L1LXT971A_PHY_ID 0x001378E0
+#define RTL8211B_PHY_ID 0x001CC910
+#define RTL8201N_PHY_ID 0x8200
+#define RTL_PHY_CTRL_FD 0x0100 /* Full duplex.0=half; 1=full */
+#define RTL_PHY_CTRL_SPD_100 0x200000 /* Force 100Mb */
+
/* Bits...
* 15-5: page
* 4-0: register offset