| if ARCH_DAVINCI |
| |
| config AINTC |
| bool |
| |
| config CP_INTC |
| bool |
| |
| config ARCH_DAVINCI_DMx |
| bool |
| |
| menu "TI DaVinci Implementations" |
| |
| comment "DaVinci Core Type" |
| |
| config ARCH_DAVINCI_DM644x |
| bool "DaVinci 644x based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DM355 |
| bool "DaVinci 355 based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DM646x |
| bool "DaVinci 646x based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| config ARCH_DAVINCI_DA830 |
| bool "DA830/OMAP-L137 based system" |
| select CP_INTC |
| select ARCH_DAVINCI_DA8XX |
| |
| config ARCH_DAVINCI_DA8XX |
| bool |
| |
| config ARCH_DAVINCI_DM365 |
| bool "DaVinci 365 based system" |
| select AINTC |
| select ARCH_DAVINCI_DMx |
| |
| comment "DaVinci Board Type" |
| |
| config MACH_DAVINCI_EVM |
| bool "TI DM644x EVM" |
| default ARCH_DAVINCI_DM644x |
| depends on ARCH_DAVINCI_DM644x |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM644x EVM |
| |
| config MACH_SFFSDR |
| bool "Lyrtech SFFSDR" |
| depends on ARCH_DAVINCI_DM644x |
| help |
| Say Y here to select the Lyrtech Small Form Factor |
| Software Defined Radio (SFFSDR) board. |
| |
| config MACH_DAVINCI_DM355_EVM |
| bool "TI DM355 EVM" |
| default ARCH_DAVINCI_DM355 |
| depends on ARCH_DAVINCI_DM355 |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM355 EVM |
| |
| config MACH_DM355_LEOPARD |
| bool "DM355 Leopard board" |
| depends on ARCH_DAVINCI_DM355 |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM355 Leopard board. |
| |
| config MACH_DAVINCI_DM6467_EVM |
| bool "TI DM6467 EVM" |
| default ARCH_DAVINCI_DM646x |
| depends on ARCH_DAVINCI_DM646x |
| help |
| Configure this option to specify the whether the board used |
| for development is a DM6467 EVM |
| |
| config MACH_DAVINCI_DM365_EVM |
| bool "TI DM365 EVM" |
| default ARCH_DAVINCI_DM365 |
| depends on ARCH_DAVINCI_DM365 |
| help |
| Configure this option to specify whether the board used |
| for development is a DM365 EVM |
| |
| |
| config DAVINCI_MUX |
| bool "DAVINCI multiplexing support" |
| depends on ARCH_DAVINCI |
| default y |
| help |
| Pin multiplexing support for DAVINCI boards. If your bootloader |
| sets the multiplexing correctly, say N. Otherwise, or if unsure, |
| say Y. |
| |
| config DAVINCI_MUX_DEBUG |
| bool "Multiplexing debug output" |
| depends on DAVINCI_MUX |
| help |
| Makes the multiplexing functions print out a lot of debug info. |
| This is useful if you want to find out the correct values of the |
| multiplexing registers. |
| |
| config DAVINCI_MUX_WARNINGS |
| bool "Warn about pins the bootloader didn't set up" |
| depends on DAVINCI_MUX |
| help |
| Choose Y here to warn whenever driver initialization logic needs |
| to change the pin multiplexing setup. When there are no warnings |
| printed, it's safe to deselect DAVINCI_MUX for your product. |
| |
| config DAVINCI_RESET_CLOCKS |
| bool "Reset unused clocks during boot" |
| depends on ARCH_DAVINCI |
| help |
| Say Y if you want to reset unused clocks during boot. |
| This option saves power, but assumes all drivers are |
| using the clock framework. Broken drivers that do not |
| yet use clock framework may not work with this option. |
| If you are booting from another operating system, you |
| probably do not want this option enabled until your |
| device drivers work properly. |
| |
| endmenu |
| |
| endif |