| /* |
| * linux/arch/arm/mach-omap2/gpmc-smsc911x.c |
| * |
| * Copyright (C) 2009 Li-Pro.Net |
| * Stephan Linz <linz@li-pro.net> |
| * |
| * Modified from linux/arch/arm/mach-omap2/gpmc-smc91x.c |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #define pr_fmt(fmt) "%s: " fmt, __func__ |
| |
| #include <linux/kernel.h> |
| #include <linux/platform_device.h> |
| #include <linux/gpio.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/smsc911x.h> |
| |
| #include <plat/board.h> |
| #include <plat/gpmc.h> |
| #include <plat/gpmc-smsc911x.h> |
| |
| static struct resource gpmc_smsc911x_resources[] = { |
| [0] = { |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, |
| }, |
| }; |
| |
| static struct smsc911x_platform_config gpmc_smsc911x_config = { |
| .phy_interface = PHY_INTERFACE_MODE_MII, |
| .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
| }; |
| |
| /* |
| * Initialize smsc911x device connected to the GPMC. Note that we |
| * assume that pin multiplexing is done in the board-*.c file, |
| * or in the bootloader. |
| */ |
| void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *gpmc_cfg) |
| { |
| struct platform_device *pdev; |
| unsigned long cs_mem_base; |
| int ret; |
| |
| if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) { |
| pr_err("Failed to request GPMC mem region\n"); |
| return; |
| } |
| |
| gpmc_smsc911x_resources[0].start = cs_mem_base + 0x0; |
| gpmc_smsc911x_resources[0].end = cs_mem_base + 0xff; |
| |
| if (gpio_request_one(gpmc_cfg->gpio_irq, GPIOF_IN, "smsc911x irq")) { |
| pr_err("Failed to request IRQ GPIO%d\n", gpmc_cfg->gpio_irq); |
| goto free1; |
| } |
| |
| gpmc_smsc911x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq); |
| |
| if (gpio_is_valid(gpmc_cfg->gpio_reset)) { |
| ret = gpio_request_one(gpmc_cfg->gpio_reset, |
| GPIOF_OUT_INIT_HIGH, "smsc911x reset"); |
| if (ret) { |
| pr_err("Failed to request reset GPIO%d\n", |
| gpmc_cfg->gpio_reset); |
| goto free2; |
| } |
| |
| gpio_set_value(gpmc_cfg->gpio_reset, 0); |
| msleep(100); |
| gpio_set_value(gpmc_cfg->gpio_reset, 1); |
| } |
| |
| gpmc_smsc911x_config.flags = gpmc_cfg->flags ? : SMSC911X_USE_16BIT; |
| |
| pdev = platform_device_register_resndata(NULL, "smsc911x", gpmc_cfg->id, |
| gpmc_smsc911x_resources, ARRAY_SIZE(gpmc_smsc911x_resources), |
| &gpmc_smsc911x_config, sizeof(gpmc_smsc911x_config)); |
| if (!pdev) { |
| pr_err("Unable to register platform device\n"); |
| gpio_free(gpmc_cfg->gpio_reset); |
| goto free2; |
| } |
| |
| return; |
| |
| free2: |
| gpio_free(gpmc_cfg->gpio_irq); |
| free1: |
| gpmc_cs_free(gpmc_cfg->cs); |
| |
| pr_err("Could not initialize smsc911x device\n"); |
| } |