iwlwifi: delay firmware loading from pci_probe to network interface open
This patch moves the firmware loading (read firmware from disk and load
it into the device SRAM) from pci_probe time to the first network
interface open time. There are two reasons for doing this:
1. To support kernel buildin iwlwifi drivers. Because kernel initializes
network devices subsystem before hard disk and SATA subsystem, it is
impossible to get the firmware image from hard disk in the PCI probe
handler. Thus delaying the firmware loading into the network
interface open time is the way to go. Note, we only read the firmware
image from hard disk the first time the interface is open. After this
is succeeded, we cache the firmware image into the host memory. This
is a performance gain when user open and close the interface multiple
times and is necessary for device suspend and resume.
2. For better power saving. When the iwlwifi modules are loaded (or
buildin the kernel) but the wireless network interface is not being
used, it is a good practice the wireless device consumes as less
power as possible. Unloading the firmware from the wireless device
and unregister the driver's interrupt handler in the network
interface close handler provides users a way to achieve this. User
space network configuration tools (i.e NetworkManager) can also
contribute here when it detects a wired cable is connected and
close the wireless interface automatically.
This patch also includes the pci_save/restore_state() fixed by Ian Schram
upon the first version.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl4965-base.c b/drivers/net/wireless/iwlwifi/iwl4965-base.c
index ad824c6..98f09e6 100644
--- a/drivers/net/wireless/iwlwifi/iwl4965-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl4965-base.c
@@ -6608,31 +6608,12 @@
}
iwl4965_init_geos(priv);
+ iwl4965_reset_channel_flag(priv);
if (iwl4965_is_rfkill(priv))
return;
- if (!priv->mac80211_registered) {
- /* Unlock so any user space entry points can call back into
- * the driver without a deadlock... */
- mutex_unlock(&priv->mutex);
- iwl4965_rate_control_register(priv->hw);
- rc = ieee80211_register_hw(priv->hw);
- priv->hw->conf.beacon_int = 100;
- mutex_lock(&priv->mutex);
-
- if (rc) {
- iwl4965_rate_control_unregister(priv->hw);
- IWL_ERROR("Failed to register network "
- "device (error %d)\n", rc);
- return;
- }
-
- priv->mac80211_registered = 1;
-
- iwl4965_reset_channel_flag(priv);
- } else
- ieee80211_start_queues(priv->hw);
+ ieee80211_start_queues(priv->hw);
priv->active_rate = priv->rates_mask;
priv->active_rate_basic = priv->rates_mask & IWL_BASIC_RATES_MASK;
@@ -6663,7 +6644,9 @@
set_bit(STATUS_READY, &priv->status);
iwl4965_rf_kill_ct_config(priv);
+
IWL_DEBUG_INFO("ALIVE processing complete.\n");
+ wake_up_interruptible(&priv->wait_command_queue);
if (priv->error_recovering)
iwl4965_error_recovery(priv);
@@ -6777,7 +6760,6 @@
static int __iwl4965_up(struct iwl4965_priv *priv)
{
- DECLARE_MAC_BUF(mac);
int rc, i;
u32 hw_rf_kill = 0;
@@ -6822,7 +6804,7 @@
* This will be used to initialize the on-board processor's
* data SRAM for a clean start when the runtime program first loads. */
memcpy(priv->ucode_data_backup.v_addr, priv->ucode_data.v_addr,
- priv->ucode_data.len);
+ priv->ucode_data.len);
/* If platform's RF_KILL switch is set to KILL,
* wait for BIT_INT_RF_KILL interrupt before loading uCode
@@ -6853,13 +6835,6 @@
/* start card; "initialize" will load runtime ucode */
iwl4965_nic_start(priv);
- /* MAC Address location in EEPROM is same for 3945/4965 */
- get_eeprom_mac(priv, priv->mac_addr);
- IWL_DEBUG_INFO("MAC address: %s\n",
- print_mac(mac, priv->mac_addr));
-
- SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
-
IWL_DEBUG_INFO(DRV_NAME " is coming up\n");
return 0;
@@ -7365,23 +7340,73 @@
*
*****************************************************************************/
+#define UCODE_READY_TIMEOUT (2 * HZ)
+
static int iwl4965_mac_start(struct ieee80211_hw *hw)
{
struct iwl4965_priv *priv = hw->priv;
+ int ret;
IWL_DEBUG_MAC80211("enter\n");
+ if (pci_enable_device(priv->pci_dev)) {
+ IWL_ERROR("Fail to pci_enable_device\n");
+ return -ENODEV;
+ }
+ pci_restore_state(priv->pci_dev);
+ pci_enable_msi(priv->pci_dev);
+
+ ret = request_irq(priv->pci_dev->irq, iwl4965_isr, IRQF_SHARED,
+ DRV_NAME, priv);
+ if (ret) {
+ IWL_ERROR("Error allocating IRQ %d\n", priv->pci_dev->irq);
+ goto out_disable_msi;
+ }
+
/* we should be verifying the device is ready to be opened */
mutex_lock(&priv->mutex);
+ memset(&priv->staging_rxon, 0, sizeof(struct iwl4965_rxon_cmd));
+ /* fetch ucode file from disk, alloc and copy to bus-master buffers ...
+ * ucode filename and max sizes are card-specific. */
+
+ if (!priv->ucode_code.len) {
+ ret = iwl4965_read_ucode(priv);
+ if (ret) {
+ IWL_ERROR("Could not read microcode: %d\n", ret);
+ mutex_unlock(&priv->mutex);
+ goto out_release_irq;
+ }
+ }
+
+ IWL_DEBUG_INFO("Start UP work.\n");
+ __iwl4965_up(priv);
+
priv->is_open = 1;
-
- if (!iwl4965_is_rfkill(priv))
- ieee80211_start_queues(priv->hw);
-
mutex_unlock(&priv->mutex);
+
+ /* Wait for START_ALIVE from ucode. Otherwise callbacks from
+ * mac80211 will not be run successfully. */
+ ret = wait_event_interruptible_timeout(priv->wait_command_queue,
+ test_bit(STATUS_READY, &priv->status),
+ UCODE_READY_TIMEOUT);
+ if (!ret) {
+ if (!test_bit(STATUS_READY, &priv->status)) {
+ IWL_ERROR("Wait for START_ALIVE timeout after %dms.\n",
+ jiffies_to_msecs(UCODE_READY_TIMEOUT));
+ ret = -ETIMEDOUT;
+ goto out_release_irq;
+ }
+ }
+
IWL_DEBUG_MAC80211("leave\n");
return 0;
+
+out_release_irq:
+ free_irq(priv->pci_dev->irq, priv);
+out_disable_msi:
+ pci_disable_msi(priv->pci_dev);
+ return ret;
}
static void iwl4965_mac_stop(struct ieee80211_hw *hw)
@@ -7390,23 +7415,25 @@
IWL_DEBUG_MAC80211("enter\n");
-
- mutex_lock(&priv->mutex);
/* stop mac, cancel any scan request and clear
* RXON_FILTER_ASSOC_MSK BIT
*/
priv->is_open = 0;
- if (!iwl4965_is_ready_rf(priv)) {
- IWL_DEBUG_MAC80211("leave - RF not ready\n");
+
+ if (iwl4965_is_ready_rf(priv)) {
+ mutex_lock(&priv->mutex);
+ iwl4965_scan_cancel_timeout(priv, 100);
+ cancel_delayed_work(&priv->post_associate);
mutex_unlock(&priv->mutex);
- return;
}
- iwl4965_scan_cancel_timeout(priv, 100);
- cancel_delayed_work(&priv->post_associate);
- priv->staging_rxon.filter_flags &= ~RXON_FILTER_ASSOC_MSK;
- iwl4965_commit_rxon(priv);
- mutex_unlock(&priv->mutex);
+ iwl4965_down(priv);
+
+ flush_workqueue(priv->workqueue);
+ free_irq(priv->pci_dev->irq, priv);
+ pci_disable_msi(priv->pci_dev);
+ pci_save_state(priv->pci_dev);
+ pci_disable_device(priv->pci_dev);
IWL_DEBUG_MAC80211("leave\n");
}
@@ -7458,11 +7485,13 @@
IWL_DEBUG_MAC80211("Set %s\n", print_mac(mac, conf->mac_addr));
memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN);
}
- iwl4965_set_mode(priv, conf->type);
- IWL_DEBUG_MAC80211("leave\n");
+ if (iwl4965_is_ready(priv))
+ iwl4965_set_mode(priv, conf->type);
+
mutex_unlock(&priv->mutex);
+ IWL_DEBUG_MAC80211("leave\n");
return 0;
}
@@ -7564,9 +7593,9 @@
IWL_DEBUG_MAC80211("leave\n");
- mutex_unlock(&priv->mutex);
out:
clear_bit(STATUS_CONF_PENDING, &priv->status);
+ mutex_unlock(&priv->mutex);
return ret;
}
@@ -7651,6 +7680,9 @@
return 0;
}
+ if (!iwl4965_is_alive(priv))
+ return -EAGAIN;
+
mutex_lock(&priv->mutex);
if (conf->bssid)
@@ -8995,6 +9027,7 @@
struct iwl4965_priv *priv;
struct ieee80211_hw *hw;
int i;
+ DECLARE_MAC_BUF(mac);
/* Disabling hardware scan means that mac80211 will perform scans
* "the hard way", rather than using device's scan. */
@@ -9136,7 +9169,6 @@
/* Device-specific setup */
if (iwl4965_hw_set_hw_setting(priv)) {
IWL_ERROR("failed to set hw settings\n");
- mutex_unlock(&priv->mutex);
goto out_iounmap;
}
@@ -9161,50 +9193,53 @@
iwl4965_disable_interrupts(priv);
- pci_enable_msi(pdev);
-
- err = request_irq(pdev->irq, iwl4965_isr, IRQF_SHARED, DRV_NAME, priv);
- if (err) {
- IWL_ERROR("Error allocating IRQ %d\n", pdev->irq);
- goto out_disable_msi;
- }
-
- mutex_lock(&priv->mutex);
-
err = sysfs_create_group(&pdev->dev.kobj, &iwl4965_attribute_group);
if (err) {
IWL_ERROR("failed to create sysfs device attributes\n");
- mutex_unlock(&priv->mutex);
goto out_release_irq;
}
- /* fetch ucode file from disk, alloc and copy to bus-master buffers ...
- * ucode filename and max sizes are card-specific. */
- err = iwl4965_read_ucode(priv);
+ /* nic init */
+ iwl4965_set_bit(priv, CSR_GIO_CHICKEN_BITS,
+ CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER);
+
+ iwl4965_set_bit(priv, CSR_GP_CNTRL, CSR_GP_CNTRL_REG_FLAG_INIT_DONE);
+ err = iwl4965_poll_bit(priv, CSR_GP_CNTRL,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY,
+ CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY, 25000);
+ if (err < 0) {
+ IWL_DEBUG_INFO("Failed to init the card\n");
+ goto out_remove_sysfs;
+ }
+ /* Read the EEPROM */
+ err = iwl4965_eeprom_init(priv);
if (err) {
- IWL_ERROR("Could not read microcode: %d\n", err);
- mutex_unlock(&priv->mutex);
- goto out_pci_alloc;
+ IWL_ERROR("Unable to init EEPROM\n");
+ goto out_remove_sysfs;
+ }
+ /* MAC Address location in EEPROM same for 3945/4965 */
+ get_eeprom_mac(priv, priv->mac_addr);
+ IWL_DEBUG_INFO("MAC address: %s\n", print_mac(mac, priv->mac_addr));
+ SET_IEEE80211_PERM_ADDR(priv->hw, priv->mac_addr);
+
+ iwl4965_rate_control_register(priv->hw);
+ err = ieee80211_register_hw(priv->hw);
+ if (err) {
+ IWL_ERROR("Failed to register network device (error %d)\n", err);
+ goto out_remove_sysfs;
}
- mutex_unlock(&priv->mutex);
-
- IWL_DEBUG_INFO("Queueing UP work.\n");
-
- queue_work(priv->workqueue, &priv->up);
+ priv->hw->conf.beacon_int = 100;
+ priv->mac80211_registered = 1;
+ pci_save_state(pdev);
+ pci_disable_device(pdev);
return 0;
- out_pci_alloc:
- iwl4965_dealloc_ucode_pci(priv);
-
+ out_remove_sysfs:
sysfs_remove_group(&pdev->dev.kobj, &iwl4965_attribute_group);
out_release_irq:
- free_irq(pdev->irq, priv);
-
- out_disable_msi:
- pci_disable_msi(pdev);
destroy_workqueue(priv->workqueue);
priv->workqueue = NULL;
iwl4965_unset_hw_setting(priv);
@@ -9270,8 +9305,6 @@
destroy_workqueue(priv->workqueue);
priv->workqueue = NULL;
- free_irq(pdev->irq, priv);
- pci_disable_msi(pdev);
pci_iounmap(pdev, priv->hw_base);
pci_release_regions(pdev);
pci_disable_device(pdev);