wl12xx: 1281/1283 support - Add Definitions
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
diff --git a/drivers/net/wireless/wl12xx/boot.h b/drivers/net/wireless/wl12xx/boot.h
index 17229b8..1f5ee31 100644
--- a/drivers/net/wireless/wl12xx/boot.h
+++ b/drivers/net/wireless/wl12xx/boot.h
@@ -74,4 +74,52 @@
#define FREF_CLK_POLARITY_BITS 0xfffff8ff
#define CLK_REQ_OUTN_SEL 0x700
+/* PLL configuration algorithm for wl128x */
+#define SYS_CLK_CFG_REG 0x2200
+/* Bit[0] - 0-TCXO, 1-FREF */
+#define MCS_PLL_CLK_SEL_FREF BIT(0)
+/* Bit[3:2] - 01-TCXO, 10-FREF */
+#define WL_CLK_REQ_TYPE_FREF BIT(3)
+#define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2))
+/* Bit[4] - 0-TCXO, 1-FREF */
+#define PRCM_CM_EN_MUX_WLAN_FREF BIT(4)
+
+#define TCXO_ILOAD_INT_REG 0x2264
+#define TCXO_CLK_DETECT_REG 0x2266
+
+#define TCXO_DET_FAILED BIT(4)
+
+#define FREF_ILOAD_INT_REG 0x2084
+#define FREF_CLK_DETECT_REG 0x2086
+#define FREF_CLK_DETECT_FAIL BIT(4)
+
+/* Use this reg for masking during driver access */
+#define WL_SPARE_REG 0x2320
+#define WL_SPARE_VAL BIT(2)
+/* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */
+#define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3))
+
+#define PLL_LOCK_COUNTERS_REG 0xD8C
+#define PLL_LOCK_COUNTERS_COEX 0x0F
+#define PLL_LOCK_COUNTERS_MCS 0xF0
+#define MCS_PLL_OVERRIDE_REG 0xD90
+#define MCS_PLL_CONFIG_REG 0xD92
+#define MCS_SEL_IN_FREQ_MASK 0x0070
+#define MCS_SEL_IN_FREQ_SHIFT 4
+#define MCS_PLL_CONFIG_REG_VAL 0x73
+
+#define MCS_PLL_M_REG 0xD94
+#define MCS_PLL_N_REG 0xD96
+#define MCS_PLL_M_REG_VAL 0xC8
+#define MCS_PLL_N_REG_VAL 0x07
+
+#define SDIO_IO_DS 0xd14
+
+/* SDIO/wSPI DS configuration values */
+#define HCI_IO_DS_8MA 0
+#define HCI_IO_DS_4MA 1 /* default */
+#define HCI_IO_DS_6MA 2
+#define HCI_IO_DS_2MA 3
+/* end PLL configuration algorithm for wl128x */
+
#endif