| #ifndef __LINUX_IBMTR_H__ |
| #define __LINUX_IBMTR_H__ |
| |
| /* Definitions for an IBM Token Ring card. */ |
| /* This file is distributed under the GNU GPL */ |
| |
| /* ported to the Alpha architecture 02/20/96 (just used the HZ macro) */ |
| |
| #define TR_RETRY_INTERVAL (30*HZ) /* 500 on PC = 5 s */ |
| #define TR_RST_TIME (HZ/20) /* 5 on PC = 50 ms */ |
| #define TR_BUSY_INTERVAL (HZ/5) /* 5 on PC = 200 ms */ |
| #define TR_SPIN_INTERVAL (3*HZ) /* 3 seconds before init timeout */ |
| |
| #define TR_ISA 1 |
| #define TR_MCA 2 |
| #define TR_ISAPNP 3 |
| #define NOTOK 0 |
| |
| #define IBMTR_SHARED_RAM_SIZE 0x10000 |
| #define IBMTR_IO_EXTENT 4 |
| #define IBMTR_MAX_ADAPTERS 4 |
| |
| #define CHANNEL_ID 0X1F30 |
| #define AIP 0X1F00 |
| #define AIPADAPTYPE 0X1FA0 |
| #define AIPDATARATE 0X1FA2 |
| #define AIPEARLYTOKEN 0X1FA4 |
| #define AIPAVAILSHRAM 0X1FA6 |
| #define AIPSHRAMPAGE 0X1FA8 |
| #define AIP4MBDHB 0X1FAA |
| #define AIP16MBDHB 0X1FAC |
| #define AIPFID 0X1FBA |
| |
| #define ADAPTRESET 0x1 /* Control Adapter reset (add to base) */ |
| #define ADAPTRESETREL 0x2 /* Release Adapter from reset ( """) */ |
| #define ADAPTINTREL 0x3 /* Adapter interrupt release */ |
| |
| #define GLOBAL_INT_ENABLE 0x02f0 |
| |
| /* MMIO bits 0-4 select register */ |
| #define RRR_EVEN 0x00 /* Shared RAM relocation registers - even and odd */ |
| /* Used to set the starting address of shared RAM */ |
| /* Bits 1 through 7 of this register map to bits 13 through 19 of the shared |
| RAM address.*/ |
| /* ie: 0x02 sets RAM address to ...ato! issy su wazzoo !! GODZILLA!!! */ |
| #define RRR_ODD 0x01 |
| /* Bits 2 and 3 of this register can be read to determine shared RAM size */ |
| /* 00 for 8k, 01 for 16k, 10 for 32k, 11 for 64k */ |
| #define WRBR_EVEN 0x02 /* Write region base registers - even and odd */ |
| #define WRBR_ODD 0x03 |
| #define WWOR_EVEN 0x04 /* Write window open registers - even and odd */ |
| #define WWOR_ODD 0x05 |
| #define WWCR_EVEN 0x06 /* Write window close registers - even and odd */ |
| #define WWCR_ODD 0x07 |
| |
| /* Interrupt status registers - PC system - even and odd */ |
| #define ISRP_EVEN 0x08 |
| |
| #define TCR_INT 0x10 /* Bit 4 - Timer interrupt. The TVR_EVEN timer has |
| expired. */ |
| #define ERR_INT 0x08 /* Bit 3 - Error interrupt. The adapter has had an |
| internal error. */ |
| #define ACCESS_INT 0x04 /* Bit 2 - Access interrupt. You have attempted to |
| write to an invalid area of shared RAM |
| or an invalid register within the MMIO. */ |
| /* In addition, the following bits within ISRP_EVEN can be turned on or off */ |
| /* by you to control the interrupt processing: */ |
| #define INT_ENABLE 0x40 /* Bit 6 - Interrupt enable. If 0, no interrupts will |
| occur. If 1, interrupts will occur normally. |
| Normally set to 1. */ |
| /* Bit 0 - Primary or alternate adapter. Set to zero if this adapter is the |
| primary adapter, 1 if this adapter is the alternate adapter. */ |
| |
| |
| #define ISRP_ODD 0x09 |
| |
| #define ADAP_CHK_INT 0x40 /* Bit 6 - Adapter check. the adapter has |
| encountered a serious problem and has closed |
| itself. Whoa. */ |
| #define SRB_RESP_INT 0x20 /* Bit 5 - SRB response. The adapter has accepted |
| an SRB request and set the return code within |
| the SRB. */ |
| #define ASB_FREE_INT 0x10 /* Bit 4 - ASB free. The adapter has read the ASB |
| and this area can be safely reused. This interrupt |
| is only used if your application has set the ASB |
| free request bit in ISRA_ODD or if an error was |
| detected in your response. */ |
| #define ARB_CMD_INT 0x08 /* Bit 3 - ARB command. The adapter has given you a |
| command for action. The command is located in the |
| ARB area of shared memory. */ |
| #define SSB_RESP_INT 0x04 /* Bit 2 - SSB response. The adapter has posted a |
| response to your SRB (the response is located in |
| the SSB area of shared memory). */ |
| /* Bit 1 - Bridge frame forward complete. */ |
| |
| |
| |
| #define ISRA_EVEN 0x0A /*Interrupt status registers - adapter - even and odd */ |
| /* Bit 7 - Internal parity error (on adapter's internal bus) */ |
| /* Bit 6 - Timer interrupt pending */ |
| /* Bit 5 - Access interrupt (attempt by adapter to access illegal address) */ |
| /* Bit 4 - Adapter microcode problem (microcode dead-man timer expired) */ |
| /* Bit 3 - Adapter processor check status */ |
| /* Bit 2 - Reserved */ |
| /* Bit 1 - Adapter hardware interrupt mask (prevents internal interrupts) */ |
| /* Bit 0 - Adapter software interrupt mask (prevents internal software ints) */ |
| |
| #define ISRA_ODD 0x0B |
| #define CMD_IN_SRB 0x20 /* Bit 5 - Indicates that you have placed a new |
| command in the SRB and are ready for the adapter to |
| process the command. */ |
| #define RESP_IN_ASB 0x10 /* Bit 4 - Indicates that you have placed a response |
| (an ASB) in the shared RAM which is available for |
| the adapter's use. */ |
| /* Bit 3 - Indicates that you are ready to put an SRB in the shared RAM, but |
| that a previous command is still pending. The adapter will then |
| interrupt you when the previous command is completed */ |
| /* Bit 2 - Indicates that you are ready to put an ASB in the shared RAM, but |
| that a previous ASB is still pending. The adapter will then interrupt |
| you when the previous ASB is copied. */ |
| #define ARB_FREE 0x2 |
| #define SSB_FREE 0x1 |
| |
| #define TCR_EVEN 0x0C /* Timer control registers - even and odd */ |
| #define TCR_ODD 0x0D |
| #define TVR_EVEN 0x0E /* Timer value registers - even and odd */ |
| #define TVR_ODD 0x0F |
| #define SRPR_EVEN 0x18 /* Shared RAM paging registers - even and odd */ |
| #define SRPR_ENABLE_PAGING 0xc0 |
| #define SRPR_ODD 0x19 /* Not used. */ |
| #define TOKREAD 0x60 |
| #define TOKOR 0x40 |
| #define TOKAND 0x20 |
| #define TOKWRITE 0x00 |
| |
| /* MMIO bits 5-6 select operation */ |
| /* 00 is used to write to a register */ |
| /* 01 is used to bitwise AND a byte with a register */ |
| /* 10 is used to bitwise OR a byte with a register */ |
| /* 11 is used to read from a register */ |
| |
| /* MMIO bits 7-8 select area of interest.. see below */ |
| /* 00 selects attachment control area. */ |
| /* 01 is reserved. */ |
| /* 10 selects adapter identification area A containing the adapter encoded |
| address. */ |
| /* 11 selects the adapter identification area B containing test patterns. */ |
| |
| #define PCCHANNELID 5049434F3631313039393020 |
| #define MCCHANNELID 4D4152533633583435313820 |
| |
| #define ACA_OFFSET 0x1e00 |
| #define ACA_SET 0x40 |
| #define ACA_RESET 0x20 |
| #define ACA_RW 0x00 |
| |
| #ifdef ENABLE_PAGING |
| #define SET_PAGE(x) (writeb((x), ti->mmio + ACA_OFFSET+ ACA_RW + SRPR_EVEN)) |
| #else |
| #define SET_PAGE(x) |
| #endif |
| |
| /* do_tok_int possible values */ |
| #define FIRST_INT 1 |
| #define NOT_FIRST 2 |
| |
| typedef enum { CLOSED, OPEN } open_state; |
| //staic const char *printstate[] = { "CLOSED","OPEN"}; |
| |
| struct tok_info { |
| unsigned char irq; |
| void __iomem *mmio; |
| unsigned char hw_address[32]; |
| unsigned char adapter_type; |
| unsigned char data_rate; |
| unsigned char token_release; |
| unsigned char avail_shared_ram; |
| unsigned char shared_ram_paging; |
| unsigned char turbo; |
| unsigned short dhb_size4mb; |
| unsigned short rbuf_len4; |
| unsigned short rbuf_cnt4; |
| unsigned short maxmtu4; |
| unsigned short dhb_size16mb; |
| unsigned short rbuf_len16; |
| unsigned short rbuf_cnt16; |
| unsigned short maxmtu16; |
| /* Additions by David Morris */ |
| unsigned char do_tok_int; |
| wait_queue_head_t wait_for_reset; |
| unsigned char sram_base; |
| /* Additions by Peter De Schrijver */ |
| unsigned char page_mask; /* mask to select RAM page to Map*/ |
| unsigned char mapped_ram_size; /* size of RAM page */ |
| __u32 sram_phys; /* Shared memory base address */ |
| void __iomem *sram_virt; /* Shared memory base address */ |
| void __iomem *init_srb; /* Initial System Request Block address */ |
| void __iomem *srb; /* System Request Block address */ |
| void __iomem *ssb; /* System Status Block address */ |
| void __iomem *arb; /* Adapter Request Block address */ |
| void __iomem *asb; /* Adapter Status Block address */ |
| __u8 init_srb_page; |
| __u8 srb_page; |
| __u8 ssb_page; |
| __u8 arb_page; |
| __u8 asb_page; |
| unsigned short exsap_station_id; |
| unsigned short global_int_enable; |
| struct sk_buff *current_skb; |
| struct net_device_stats tr_stats; |
| unsigned char auto_speedsave; |
| open_state open_status, sap_status; |
| enum {MANUAL, AUTOMATIC} open_mode; |
| enum {FAIL, RESTART, REOPEN} open_action; |
| enum {NO, YES} open_failure; |
| unsigned char readlog_pending; |
| unsigned short adapter_int_enable; /* Adapter-specific int enable */ |
| struct timer_list tr_timer; |
| unsigned char ring_speed; |
| spinlock_t lock; /* SMP protection */ |
| }; |
| |
| /* token ring adapter commands */ |
| #define DIR_INTERRUPT 0x00 /* struct srb_interrupt */ |
| #define DIR_MOD_OPEN_PARAMS 0x01 |
| #define DIR_OPEN_ADAPTER 0x03 /* struct dir_open_adapter */ |
| #define DIR_CLOSE_ADAPTER 0x04 |
| #define DIR_SET_GRP_ADDR 0x06 |
| #define DIR_SET_FUNC_ADDR 0x07 /* struct srb_set_funct_addr */ |
| #define DIR_READ_LOG 0x08 /* struct srb_read_log */ |
| #define DLC_OPEN_SAP 0x15 /* struct dlc_open_sap */ |
| #define DLC_CLOSE_SAP 0x16 |
| #define DATA_LOST 0x20 /* struct asb_rec */ |
| #define REC_DATA 0x81 /* struct arb_rec_req */ |
| #define XMIT_DATA_REQ 0x82 /* struct arb_xmit_req */ |
| #define DLC_STATUS 0x83 /* struct arb_dlc_status */ |
| #define RING_STAT_CHANGE 0x84 /* struct dlc_open_sap ??? */ |
| |
| /* DIR_OPEN_ADAPTER options */ |
| #define OPEN_PASS_BCON_MAC 0x0100 |
| #define NUM_RCV_BUF 2 |
| #define RCV_BUF_LEN 1024 |
| #define DHB_LENGTH 2048 |
| #define NUM_DHB 2 |
| #define DLC_MAX_SAP 2 |
| #define DLC_MAX_STA 1 |
| |
| /* DLC_OPEN_SAP options */ |
| #define MAX_I_FIELD 0x0088 |
| #define SAP_OPEN_IND_SAP 0x04 |
| #define SAP_OPEN_PRIORITY 0x20 |
| #define SAP_OPEN_STATION_CNT 0x1 |
| #define XMIT_DIR_FRAME 0x0A |
| #define XMIT_UI_FRAME 0x0d |
| #define XMIT_XID_CMD 0x0e |
| #define XMIT_TEST_CMD 0x11 |
| |
| /* srb close return code */ |
| #define SIGNAL_LOSS 0x8000 |
| #define HARD_ERROR 0x4000 |
| #define XMIT_BEACON 0x1000 |
| #define LOBE_FAULT 0x0800 |
| #define AUTO_REMOVAL 0x0400 |
| #define REMOVE_RECV 0x0100 |
| #define LOG_OVERFLOW 0x0080 |
| #define RING_RECOVER 0x0020 |
| |
| struct srb_init_response { |
| unsigned char command; |
| unsigned char init_status; |
| unsigned char init_status_2; |
| unsigned char reserved[3]; |
| __u16 bring_up_code; |
| __u16 encoded_address; |
| __u16 level_address; |
| __u16 adapter_address; |
| __u16 parms_address; |
| __u16 mac_address; |
| }; |
| |
| struct dir_open_adapter { |
| unsigned char command; |
| char reserved[7]; |
| __u16 open_options; |
| unsigned char node_address[6]; |
| unsigned char group_address[4]; |
| unsigned char funct_address[4]; |
| __u16 num_rcv_buf; |
| __u16 rcv_buf_len; |
| __u16 dhb_length; |
| unsigned char num_dhb; |
| char reserved2; |
| unsigned char dlc_max_sap; |
| unsigned char dlc_max_sta; |
| unsigned char dlc_max_gsap; |
| unsigned char dlc_max_gmem; |
| unsigned char dlc_t1_tick_1; |
| unsigned char dlc_t2_tick_1; |
| unsigned char dlc_ti_tick_1; |
| unsigned char dlc_t1_tick_2; |
| unsigned char dlc_t2_tick_2; |
| unsigned char dlc_ti_tick_2; |
| unsigned char product_id[18]; |
| }; |
| |
| struct dlc_open_sap { |
| unsigned char command; |
| unsigned char reserved1; |
| unsigned char ret_code; |
| unsigned char reserved2; |
| __u16 station_id; |
| unsigned char timer_t1; |
| unsigned char timer_t2; |
| unsigned char timer_ti; |
| unsigned char maxout; |
| unsigned char maxin; |
| unsigned char maxout_incr; |
| unsigned char max_retry_count; |
| unsigned char gsap_max_mem; |
| __u16 max_i_field; |
| unsigned char sap_value; |
| unsigned char sap_options; |
| unsigned char station_count; |
| unsigned char sap_gsap_mem; |
| unsigned char gsap[0]; |
| }; |
| |
| struct srb_xmit { |
| unsigned char command; |
| unsigned char cmd_corr; |
| unsigned char ret_code; |
| unsigned char reserved1; |
| __u16 station_id; |
| }; |
| |
| struct arb_rec_req { |
| unsigned char command; |
| unsigned char reserved1[3]; |
| __u16 station_id; |
| __u16 rec_buf_addr; |
| unsigned char lan_hdr_len; |
| unsigned char dlc_hdr_len; |
| __u16 frame_len; |
| unsigned char msg_type; |
| }; |
| |
| struct asb_rec { |
| unsigned char command; |
| unsigned char reserved1; |
| unsigned char ret_code; |
| unsigned char reserved2; |
| __u16 station_id; |
| __u16 rec_buf_addr; |
| }; |
| |
| struct rec_buf { |
| unsigned char reserved1[2]; |
| __u16 buf_ptr; |
| unsigned char reserved2; |
| unsigned char receive_fs; |
| __u16 buf_len; |
| unsigned char data[0]; |
| }; |
| |
| struct srb_set_funct_addr { |
| unsigned char command; |
| unsigned char reserved1; |
| unsigned char ret_code; |
| unsigned char reserved2[3]; |
| unsigned char funct_address[4]; |
| }; |
| |
| #endif |