sky2: transmit timeout
The transmit timeout code could hang, and it would not clear out
problems if the hardware was stuck. Change the code to effectively do
a device down/up similar to the suspend/resume code.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 2c91181..fafa402 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -1866,16 +1866,13 @@
spin_unlock(&sky2->phy_lock);
}
-
/* Transmit timeout is only called if we are running, carrier is up
* and tx queue is full (stopped).
- * Called with netif_tx_lock held.
*/
static void sky2_tx_timeout(struct net_device *dev)
{
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- u32 imask;
if (netif_msg_timer(sky2))
printk(KERN_ERR PFX "%s: tx timeout\n", dev->name);
@@ -1885,19 +1882,8 @@
sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX),
sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE)));
- imask = sky2_read32(hw, B0_IMSK); /* block IRQ in hw */
- sky2_write32(hw, B0_IMSK, 0);
- sky2_read32(hw, B0_IMSK);
-
- netif_poll_disable(hw->dev[0]); /* stop NAPI poll */
- synchronize_irq(hw->pdev->irq);
-
- netif_start_queue(dev); /* don't wakeup during flush */
- sky2_tx_complete(sky2, sky2->tx_prod); /* Flush transmit queue */
-
- sky2_write32(hw, B0_IMSK, imask);
-
- sky2_phy_reinit(sky2); /* this clears flow control etc */
+ /* can't restart safely under softirq */
+ schedule_work(&hw->restart_work);
}
static int sky2_change_mtu(struct net_device *dev, int new_mtu)
@@ -2651,6 +2637,49 @@
sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START);
}
+static void sky2_restart(struct work_struct *work)
+{
+ struct sky2_hw *hw = container_of(work, struct sky2_hw, restart_work);
+ struct net_device *dev;
+ int i, err;
+
+ dev_dbg(&hw->pdev->dev, "restarting\n");
+
+ del_timer_sync(&hw->idle_timer);
+
+ rtnl_lock();
+ sky2_write32(hw, B0_IMSK, 0);
+ sky2_read32(hw, B0_IMSK);
+
+ netif_poll_disable(hw->dev[0]);
+
+ for (i = 0; i < hw->ports; i++) {
+ dev = hw->dev[i];
+ if (netif_running(dev))
+ sky2_down(dev);
+ }
+
+ sky2_reset(hw);
+ sky2_write32(hw, B0_IMSK, Y2_IS_BASE);
+ netif_poll_enable(hw->dev[0]);
+
+ for (i = 0; i < hw->ports; i++) {
+ dev = hw->dev[i];
+ if (netif_running(dev)) {
+ err = sky2_up(dev);
+ if (err) {
+ printk(KERN_INFO PFX "%s: could not restart %d\n",
+ dev->name, err);
+ dev_close(dev);
+ }
+ }
+ }
+
+ sky2_idle_start(hw);
+
+ rtnl_unlock();
+}
+
static inline u8 sky2_wol_supported(const struct sky2_hw *hw)
{
return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0;
@@ -3613,6 +3642,8 @@
}
setup_timer(&hw->idle_timer, sky2_idle, (unsigned long) hw);
+ INIT_WORK(&hw->restart_work, sky2_restart);
+
sky2_idle_start(hw);
pci_set_drvdata(pdev, hw);
@@ -3649,6 +3680,8 @@
del_timer_sync(&hw->idle_timer);
+ flush_scheduled_work();
+
sky2_write32(hw, B0_IMSK, 0);
synchronize_irq(hw->pdev->irq);