brcm80211: fmac: move busstate to struct brcmf_bus
busstate keeps track of the bus (USB/SDIO) status and is used by
both generic layer and bus layer. Move it to brcmf_bus helps to clean
up the interface. This patch is part of fullmac bus interface
refactoring.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd.h b/drivers/net/wireless/brcm80211/brcmfmac/dhd.h
index a557971..a104b74 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/dhd.h
+++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd.h
@@ -574,6 +574,7 @@
struct brcmf_bus {
u8 type; /* bus type */
void *bus_priv; /* pointer to bus private structure */
+ enum brcmf_bus_state state;
};
/* Forward decls for struct brcmf_pub (see below) */
@@ -586,6 +587,7 @@
struct brcmf_pub {
/* Linkage ponters */
struct brcmf_sdio *bus;
+ struct brcmf_bus *bus_if;
struct brcmf_proto *prot;
struct brcmf_info *info;
struct brcmf_cfg80211_dev *config;
@@ -593,7 +595,6 @@
/* Internal brcmf items */
bool up; /* Driver up/down (to OS) */
bool txoff; /* Transmit flow-controlled */
- enum brcmf_bus_state busstate;
uint hdrlen; /* Total BRCMF header length (proto + bus) */
uint maxctl; /* Max size rxctl request from proto to bus */
uint rxsz; /* Rx buffer size bus module should use */
@@ -661,7 +662,6 @@
u8 country_code[BRCM_CNTRY_BUF_SZ];
char eventmask[BRCMF_EVENTING_MASK_LEN];
-
};
struct brcmf_if_event {
@@ -687,7 +687,7 @@
* bus_hdrlen specifies required headroom for bus module header.
*/
extern struct brcmf_pub *brcmf_attach(struct brcmf_sdio *bus,
- uint bus_hdrlen);
+ uint bus_hdrlen, struct device *dev);
extern int brcmf_net_attach(struct brcmf_pub *drvr, int idx);
extern int brcmf_netdev_wait_pend8021x(struct net_device *ndev);
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.c b/drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.c
index e34c5c3..8e46bc6 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd_cdc.c
@@ -280,7 +280,7 @@
struct brcmf_proto *prot = drvr->prot;
int ret = -1;
- if (drvr->busstate == BRCMF_BUS_DOWN) {
+ if (drvr->bus_if->state == BRCMF_BUS_DOWN) {
brcmf_dbg(ERROR, "bus is down. we have nothing to do.\n");
return ret;
}
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c b/drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c
index e8f7f78..c13b30f 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c
@@ -292,7 +292,7 @@
struct brcmf_info *drvr_priv = drvr->info;
/* Reject if down */
- if (!drvr->up || (drvr->busstate == BRCMF_BUS_DOWN))
+ if (!drvr->up || (drvr->bus_if->state == BRCMF_BUS_DOWN))
return -ENODEV;
/* Update multicast statistic */
@@ -322,9 +322,11 @@
brcmf_dbg(TRACE, "Enter\n");
/* Reject if down */
- if (!drvr_priv->pub.up || (drvr_priv->pub.busstate == BRCMF_BUS_DOWN)) {
- brcmf_dbg(ERROR, "xmit rejected pub.up=%d busstate=%d\n",
- drvr_priv->pub.up, drvr_priv->pub.busstate);
+ if (!drvr_priv->pub.up ||
+ (drvr_priv->pub.bus_if->state == BRCMF_BUS_DOWN)) {
+ brcmf_dbg(ERROR, "xmit rejected pub.up=%d state=%d\n",
+ drvr_priv->pub.up,
+ drvr_priv->pub.bus_if->state);
netif_stop_queue(ndev);
return -ENODEV;
}
@@ -761,7 +763,7 @@
buflen = min_t(uint, dcmd.len, BRCMF_DCMD_MAXLEN);
/* send to dongle (must be up, and wl) */
- if ((drvr_priv->pub.busstate != BRCMF_BUS_DATA)) {
+ if ((drvr_priv->pub.bus_if->state != BRCMF_BUS_DATA)) {
brcmf_dbg(ERROR, "DONGLE_DOWN\n");
err = -EIO;
goto done;
@@ -940,7 +942,8 @@
}
}
-struct brcmf_pub *brcmf_attach(struct brcmf_sdio *bus, uint bus_hdrlen)
+struct brcmf_pub *brcmf_attach(struct brcmf_sdio *bus, uint bus_hdrlen,
+ struct device *dev)
{
struct brcmf_info *drvr_priv = NULL;
@@ -959,6 +962,7 @@
/* Link to bus module */
drvr_priv->pub.bus = bus;
drvr_priv->pub.hdrlen = bus_hdrlen;
+ drvr_priv->pub.bus_if = dev_get_drvdata(dev);
/* Attach and link in the protocol */
if (brcmf_proto_attach(&drvr_priv->pub) != 0) {
@@ -995,7 +999,7 @@
}
/* If bus is not ready, can't come up */
- if (drvr_priv->pub.busstate != BRCMF_BUS_DATA) {
+ if (drvr_priv->pub.bus_if->state != BRCMF_BUS_DATA) {
brcmf_dbg(ERROR, "failed bus is not ready\n");
return -ENODEV;
}
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
index 9ab906a..7c8b5f7 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c
@@ -1068,7 +1068,7 @@
/* If we can't reach the device, signal failure */
if (err || brcmf_sdcard_regfail(bus->sdiodev))
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
}
/* copy a buffer into a pkt buffer chain */
@@ -1714,7 +1714,8 @@
*finished = false;
for (rxseq = bus->rx_seq, rxleft = maxframes;
- !bus->rxskip && rxleft && bus->drvr->busstate != BRCMF_BUS_DOWN;
+ !bus->rxskip && rxleft &&
+ bus->drvr->bus_if->state != BRCMF_BUS_DOWN;
rxseq++, rxleft--) {
/* Handle glomming separately */
@@ -2286,7 +2287,7 @@
}
/* Deflow-control stack if needed */
- if (drvr->up && (drvr->busstate == BRCMF_BUS_DATA) &&
+ if (drvr->up && (drvr->bus_if->state == BRCMF_BUS_DATA) &&
drvr->txoff && (pktq_len(&bus->txq) < TXLOW))
brcmf_txflowcontrol(drvr, 0, OFF);
@@ -2321,7 +2322,7 @@
SBSDIO_DEVICE_CTL, &err);
if (err) {
brcmf_dbg(ERROR, "error reading DEVCTL: %d\n", err);
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
}
#endif /* BCMDBG */
@@ -2331,7 +2332,7 @@
if (err) {
brcmf_dbg(ERROR, "error reading CSR: %d\n",
err);
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
}
brcmf_dbg(INFO, "DPC: PENDING, devctl 0x%02x clkctl 0x%02x\n",
@@ -2344,7 +2345,7 @@
if (err) {
brcmf_dbg(ERROR, "error reading DEVCTL: %d\n",
err);
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
}
devctl &= ~SBSDIO_DEVCTL_CA_INT_ONLY;
brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_1,
@@ -2352,7 +2353,7 @@
if (err) {
brcmf_dbg(ERROR, "error writing DEVCTL: %d\n",
err);
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
}
bus->clkstate = CLK_AVAIL;
} else {
@@ -2508,11 +2509,11 @@
else await next interrupt */
/* On failed register access, all bets are off:
no resched or interrupts */
- if ((bus->drvr->busstate == BRCMF_BUS_DOWN) ||
+ if ((bus->drvr->bus_if->state == BRCMF_BUS_DOWN) ||
brcmf_sdcard_regfail(bus->sdiodev)) {
brcmf_dbg(ERROR, "failed backplane access over SDIO, halting operation %d\n",
brcmf_sdcard_regfail(bus->sdiodev));
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
bus->intstatus = 0;
} else if (bus->clkstate == CLK_PENDING) {
brcmf_dbg(INFO, "rescheduled due to CLK_PENDING awaiting I_CHIPACTIVE interrupt\n");
@@ -2549,7 +2550,7 @@
if (!wait_for_completion_interruptible(&bus->dpc_wait)) {
/* Call bus dpc unless it indicated down
(then clean stop) */
- if (bus->drvr->busstate != BRCMF_BUS_DOWN) {
+ if (bus->drvr->bus_if->state != BRCMF_BUS_DOWN) {
if (brcmf_sdbrcm_dpc(bus))
complete(&bus->dpc_wait);
} else {
@@ -3111,7 +3112,7 @@
/* Allow HT Clock now that the ARM is running. */
bus->alp_only = false;
- bus->drvr->busstate = BRCMF_BUS_LOAD;
+ bus->drvr->bus_if->state = BRCMF_BUS_LOAD;
}
fail:
return bcmerror;
@@ -3354,7 +3355,7 @@
bus->hostintmask = 0;
/* Change our idea of bus state */
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
/* Force clocks on backplane to be sure F2 interrupt propagates */
saveclk = brcmf_sdcard_cfg_read(bus->sdiodev, SDIO_FUNC_1,
@@ -3410,7 +3411,7 @@
brcmf_dbg(TRACE, "Enter\n");
/* try to download image and nvram to the dongle */
- if (drvr->busstate == BRCMF_BUS_DOWN) {
+ if (drvr->bus_if->state == BRCMF_BUS_DOWN) {
if (!(brcmf_sdbrcm_download_firmware(bus)))
return -1;
}
@@ -3476,7 +3477,7 @@
SBSDIO_WATERMARK, 8, &err);
/* Set bus state according to enable result */
- drvr->busstate = BRCMF_BUS_DATA;
+ drvr->bus_if->state = BRCMF_BUS_DATA;
}
else {
@@ -3491,7 +3492,7 @@
SBSDIO_FUNC1_CHIPCLKCSR, saveclk, &err);
/* If we didn't come up, turn off backplane clock */
- if (drvr->busstate != BRCMF_BUS_DATA)
+ if (drvr->bus_if->state != BRCMF_BUS_DATA)
brcmf_sdbrcm_clkctl(bus, CLK_NONE, false);
exit:
@@ -3511,7 +3512,7 @@
return;
}
- if (bus->drvr->busstate == BRCMF_BUS_DOWN) {
+ if (bus->drvr->bus_if->state == BRCMF_BUS_DOWN) {
brcmf_dbg(ERROR, "bus is down. we have nothing to do\n");
return;
}
@@ -3585,7 +3586,8 @@
}
#ifdef BCMDBG
/* Poll for console output periodically */
- if (drvr->busstate == BRCMF_BUS_DATA && bus->console_interval != 0) {
+ if (drvr->bus_if->state == BRCMF_BUS_DATA &&
+ bus->console_interval != 0) {
bus->console.count += BRCMF_WD_POLL_MS;
if (bus->console.count >= bus->console_interval) {
bus->console.count -= bus->console_interval;
@@ -3764,7 +3766,7 @@
brcmf_sdcard_cfg_write(bus->sdiodev, SDIO_FUNC_0, SDIO_CCCR_IOEx,
SDIO_FUNC_ENABLE_1, NULL);
- bus->drvr->busstate = BRCMF_BUS_DOWN;
+ bus->drvr->bus_if->state = BRCMF_BUS_DOWN;
bus->sleeping = false;
bus->rxflow = false;
@@ -3924,7 +3926,7 @@
}
/* Attach to the brcmf/OS/network interface */
- bus->drvr = brcmf_attach(bus, SDPCM_RESERVE);
+ bus->drvr = brcmf_attach(bus, SDPCM_RESERVE, bus->sdiodev->dev);
if (!bus->drvr) {
brcmf_dbg(ERROR, "brcmf_attach failed\n");
goto fail;
@@ -4003,7 +4005,7 @@
}
/* don't start the wd until fw is loaded */
- if (bus->drvr->busstate == BRCMF_BUS_DOWN)
+ if (bus->drvr->bus_if->state == BRCMF_BUS_DOWN)
return;
if (wdtick) {