arm/dt: msm8226: refactor device tree into SOC and board specific files
With the upcoming 8x26 variants, several targets will use the same device
tree files with specific overrides. Break up the device tree files into a
SOC include file and a board include file. Each new target can then select
its own include files and provided board specific overrides in the top
level DTS file.
Change-Id: Ib076f862618df89c1a609376068733f4a00dabad
Signed-off-by: Syed Rameez Mustafa <rameezmustafa@codeaurora.org>
diff --git a/arch/arm/boot/dts/msm8226-qrd.dts b/arch/arm/boot/dts/msm8226-qrd.dts
index f6e8f8b..e364de7 100644
--- a/arch/arm/boot/dts/msm8226-qrd.dts
+++ b/arch/arm/boot/dts/msm8226-qrd.dts
@@ -12,8 +12,7 @@
/dts-v1/;
/include/ "msm8226.dtsi"
-/include/ "dsi-panel-nt35590-720p-video.dtsi"
-/include/ "msm8226-camera-sensor-qrd.dtsi"
+/include/ "msm8226-qrd.dtsi"
/ {
model = "Qualcomm MSM 8226 QRD";
@@ -23,391 +22,3 @@
<159 11 0>,
<198 11 0>;
};
-
-&soc {
- serial@f991f000 {
- status = "ok";
- };
-
- qcom,mdss_dsi_nt35590_720p_video {
- status = "ok";
- };
-
- i2c@f9927000 { /* BLSP1 QUP5 */
- synaptics@20 {
- compatible = "synaptics,rmi4";
- reg = <0x20>;
- interrupt-parent = <&msmgpio>;
- interrupts = <17 0x2008>;
- vdd-supply = <&pm8226_l19>;
- vcc_i2c-supply = <&pm8226_lvs1>;
- synaptics,reset-gpio = <&msmgpio 16 0x00>;
- synaptics,irq-gpio = <&msmgpio 17 0x2008>;
- synaptics,button-map = <139 102 158>;
- synaptics,i2c-pull-up;
- synaptics,reg-en;
- };
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- input-name = "gpio-keys";
-
- camera_focus {
- label = "camera_focus";
- gpios = <&msmgpio 108 0x1>;
- linux,input-type = <1>;
- linux,code = <0x210>;
- gpio-key,wakeup;
- debounce-interval = <15>;
- };
-
- camera_snapshot {
- label = "camera_snapshot";
- gpios = <&msmgpio 107 0x1>;
- linux,input-type = <1>;
- linux,code = <0x2fe>;
- gpio-key,wakeup;
- debounce-interval = <15>;
- };
-
- vol_up {
- label = "volume_up";
- gpios = <&msmgpio 106 0x1>;
- linux,input-type = <1>;
- linux,code = <115>;
- gpio-key,wakeup;
- debounce-interval = <15>;
- };
- };
-
- spi@f9923000 {
- ethernet-switch@3 {
- compatible = "micrel,ks8851";
- reg = <3>;
- interrupt-parent = <&msmgpio>;
- interrupts = <0 115 0>;
- spi-max-frequency = <4800000>;
- rst-gpio = <&msmgpio 114 0>;
- vdd-io-supply = <&pm8226_lvs1>;
- vdd-phy-supply = <&pm8226_lvs1>;
- };
- };
-
- sound {
- qcom,audio-routing =
- "RX_BIAS", "MCLK",
- "LDO_H", "MCLK",
- "SPK_OUT", "MCLK",
- "SPK_OUT", "EXT_VDD_SPKR",
- "AMIC1", "MIC BIAS1 External",
- "MIC BIAS1 External", "Handset Mic",
- "AMIC2", "MIC BIAS2 External",
- "MIC BIAS2 External", "Headset Mic",
- "AMIC3", "MIC BIAS1 External",
- "MIC BIAS1 External", "ANCRight Headset Mic",
- "AMIC4", "MIC BIAS2 External",
- "MIC BIAS2 External", "ANCLeft Headset Mic";
-
- qcom,cdc-mclk-gpios = <&pm8226_gpios 1 0>;
- qcom,cdc-vdd-spkr-gpios = <&pm8226_gpios 2 0>;
- };
-};
-
-&sdcc1 {
- vdd-supply = <&pm8226_l17>;
- qcom,vdd-always-on;
- qcom,vdd-lpm-sup;
- qcom,vdd-voltage-level = <2950000 2950000>;
- qcom,vdd-current-level = <800 500000>;
-
- vdd-io-supply = <&pm8226_l6>;
- qcom,vdd-io-always-on;
- qcom,vdd-io-voltage-level = <1800000 1800000>;
- qcom,vdd-io-current-level = <250 154000>;
-
- qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
- qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
-
- qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
- qcom,sup-voltages = <2950 2950>;
-
- qcom,bus-speed-mode = "HS200_1p8v", "DDR_1p8v";
- qcom,nonremovable;
-
- status = "disabled";
-};
-
-&sdhc_1 {
- vdd-supply = <&pm8226_l17>;
- qcom,vdd-always-on;
- qcom,vdd-lpm-sup;
- qcom,vdd-voltage-level = <2950000 2950000>;
- qcom,vdd-current-level = <800 500000>;
-
- vdd-io-supply = <&pm8226_l6>;
- qcom,vdd-io-always-on;
- qcom,vdd-io-voltage-level = <1800000 1800000>;
- qcom,vdd-io-current-level = <250 154000>;
-
- qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
- qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
-
- qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
- qcom,bus-speed-mode = "HS200_1p8v", "DDR_1p8v";
- qcom,nonremovable;
-
- status = "ok";
-};
-
-&sdcc2 {
- vdd-supply = <&pm8226_l18>;
- qcom,vdd-voltage-level = <2950000 2950000>;
- qcom,vdd-current-level = <9000 800000>;
-
- vdd-io-supply = <&pm8226_l21>;
- qcom,vdd-io-always-on;
- qcom,vdd-io-lpm-sup;
- qcom,vdd-io-voltage-level = <1800000 2950000>;
- qcom,vdd-io-current-level = <6 22000>;
-
- qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
- qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
-
- qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
- qcom,sup-voltages = <2950 2950>;
-
- qcom,xpc;
- qcom,bus-speed-mode = "SDR12", "SDR25", "SDR50", "DDR50", "SDR104";
- qcom,current-limit = <600>;
-
- #address-cells = <0>;
- interrupt-parent = <&sdcc2>;
- interrupts = <0 1 2>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0xffffffff>;
- interrupt-map = <0 &intc 0 125 0
- 1 &intc 0 220 0
- 2 &msmgpio 38 0x3>;
- interrupt-names = "core_irq", "bam_irq", "status_irq";
- cd-gpios = <&msmgpio 38 0x1>;
-
- status = "disabled";
-};
-
-&sdhc_2 {
- vdd-supply = <&pm8226_l18>;
- qcom,vdd-voltage-level = <2950000 2950000>;
- qcom,vdd-current-level = <9000 800000>;
-
- vdd-io-supply = <&pm8226_l21>;
- qcom,vdd-io-always-on;
- qcom,vdd-io-lpm-sup;
- qcom,vdd-io-voltage-level = <1800000 2950000>;
- qcom,vdd-io-current-level = <6 22000>;
-
- qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
- qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
- qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
-
- qcom,clk-rates = <400000 25000000 50000000 100000000 200000000>;
-
- #address-cells = <0>;
- interrupt-parent = <&sdhc_2>;
- interrupts = <0 1 2>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0xffffffff>;
- interrupt-map = <0 &intc 0 125 0
- 1 &intc 0 221 0
- 2 &msmgpio 38 0x3>;
- interrupt-names = "hc_irq", "pwr_irq", "status_irq";
- cd-gpios = <&msmgpio 38 0x1>;
-
- status = "ok";
-};
-
-&spmi_bus {
- qcom,pm8226@0 {
- qcom,leds@a100 {
- status = "okay";
- qcom,led_mpp_2 {
- label = "mpp";
- linux,name = "button-backlight";
- linux,default-trigger = "none";
- qcom,default-state = "off";
- qcom,max-current = <40>;
- qcom,current-setting = <5>;
- qcom,id = <6>;
- qcom,mode = "manual";
- qcom,source-sel = <1>;
- qcom,mode-ctrl = <0x60>;
- };
- };
-
- qcom,leds@a300 {
- status = "okay";
- qcom,led_mpp_4 {
- label = "mpp";
- linux,name = "green";
- linux,default-trigger = "none";
- qcom,default-state = "off";
- qcom,max-current = <40>;
- qcom,current-setting = <5>;
- qcom,id = <6>;
- qcom,mode = "lpg";
- qcom,source-sel = <8>;
- qcom,mode-ctrl = <0x60>;
- qcom,pwm-channel = <0>;
- qcom,start-idx = <1>;
- qcom,duty-pcts = [00 00 00 00 64
- 64 00 00 00 00];
- };
- };
-
- qcom,leds@a500 {
- status = "okay";
- qcom,led_mpp_6 {
- label = "mpp";
- linux,name = "red";
- linux,default-trigger = "none";
- qcom,default-state = "off";
- qcom,max-current = <40>;
- qcom,current-setting = <5>;
- qcom,id = <6>;
- qcom,mode-ctrl = <0x60>;
- qcom,source-sel = <10>;
- qcom,mode = "lpg";
- qcom,pwm-channel = <5>;
- qcom,start-idx = <1>;
- qcom,duty-pcts = [00 00 00 00 64
- 64 00 00 00 00];
- };
- };
- };
-
- qcom,pm8226@1 {
- qcom,leds@d300 {
- status = "okay";
- };
-
- qcom,leds@d800 {
- status = "okay";
- qcom,wled_0 {
- label = "wled";
- linux,name = "wled:backlight";
- linux,default-trigger = "bkl-trigger";
- qcom,cs-out-en;
- qcom,op-fdbck = <1>;
- qcom,default-state = "on";
- qcom,max-current = <25>;
- qcom,ctrl-delay-us = <0>;
- qcom,boost-curr-lim = <3>;
- qcom,cp-sel = <0>;
- qcom,switch-freq = <2>;
- qcom,ovp-val = <0>;
- qcom,num-strings = <1>;
- qcom,id = <0>;
- };
- };
-
- qcom,vibrator@c000 {
- status = "okay";
- qcom,vib-timeout-ms = <15000>;
- qcom,vib-vtg-level-mV = <3100>;
- };
-
- };
-};
-
-&pm8226_bms {
- status = "okay";
- qcom,batt-type = <4>;
- qcom,max-voltage-uv = <4350000>;
-};
-
-&pm8226_chg {
- status = "okay";
- qcom,chg-vddmax-mv = <4350>;
- qcom,chg-vddsafe-mv = <4350>;
-};
-
-&pm8226_gpios {
- gpio@c000 { /* GPIO 1 */
- /* XO_PMIC_CDC_MCLK enable for tapan codec */
- qcom,mode = <1>; /* Digital output */
- qcom,output-type = <0>; /* CMOS logic */
- qcom,pull = <5>; /* QPNP_PIN_PULL_NO*/
- qcom,vin-sel = <3>; /* QPNP_PIN_VIN3 */
- qcom,out-strength = <3>;/* QPNP_PIN_OUT_STRENGTH_HIGH */
- qcom,src-sel = <2>; /* QPNP_PIN_SEL_FUNC_1 */
- qcom,master-en = <1>; /* Enable GPIO */
- };
-
- gpio@c100 { /* GPIO 2 */
- qcom,mode = <1>;
- qcom,output-type = <0>;
- qcom,pull = <5>;
- qcom,vin-sel = <3>;
- qcom,out-strength = <3>;
- qcom,src-sel = <2>;
- qcom,master-en = <1>;
- };
-
- gpio@c200 { /* GPIO 3 */
- };
-
- gpio@c300 { /* GPIO 4 */
- };
-
- gpio@c400 { /* GPIO 5 */
- };
-
- gpio@c500 { /* GPIO 6 */
- };
-
- gpio@c600 { /* GPIO 7 */
- };
-
- gpio@c700 { /* GPIO 8 */
- };
-};
-
-&pm8226_mpps {
- mpp@a000 { /* MPP 1 */
- };
-
- mpp@a100 { /* MPP 2 */
- };
-
- mpp@a200 { /* MPP 3 */
- };
-
- mpp@a300 { /* MPP 4 */
- };
-
- mpp@a400 { /* MPP 5 */
- };
-
- mpp@a500 { /* MPP 6 */
- };
-
- mpp@a600 { /* MPP 7 */
- };
-
- mpp@a700 { /* MPP 8 */
- };
-};
-
-&slim_msm {
- tapan_codec {
- qcom,cdc-micbias1-ext-cap;
- };
-
-};