blob: 20e8a96e57071ba0c790c41b9f6de92d3c523246 [file] [log] [blame]
/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
&spmi_bus {
#address-cells = <1>;
#size-cells = <0>;
interrupt-controller;
#interrupt-cells = <3>;
qcom,pm8110@0 {
spmi-slave-container;
reg = <0x0>;
#address-cells = <1>;
#size-cells = <1>;
qcom,revid@100 {
compatible = "qcom,qpnp-revid";
reg = <0x100 0x100>;
};
qcom,power-on@800 {
compatible = "qcom,qpnp-power-on";
reg = <0x800 0x100>;
interrupts = <0x0 0x8 0x0>,
<0x0 0x8 0x1>,
<0x0 0x8 0x4>;
interrupt-names = "kpdpwr", "resin", "resin-bark";
qcom,pon-dbc-delay = <15625>;
qcom,system-reset;
qcom,pon_1 {
qcom,pon-type = <0>;
qcom,pull-up = <1>;
linux,code = <116>;
};
qcom,pon_2 {
qcom,pon-type = <1>;
qcom,pull-up = <1>;
linux,code = <114>;
};
};
pm8110_chg: qcom,charger {
spmi-dev-container;
compatible = "qcom,qpnp-charger";
#address-cells = <1>;
#size-cells = <1>;
status = "disabled";
qcom,vddmax-mv = <4200>;
qcom,vddsafe-mv = <4230>;
qcom,vinmin-mv = <4300>;
qcom,vbatdet-mv = <4100>;
qcom,ibatmax-ma = <1500>;
qcom,ibatterm-ma = <100>;
qcom,ibatsafe-ma = <1500>;
qcom,thermal-mitigation = <1500 700 600 325>;
qcom,vbatdet-delta-mv = <100>;
qcom,resume-soc = <99>;
qcom,tchg-mins = <150>;
qcom,chg-vadc = <&pm8110_vadc>;
qcom,chg-adc_tm = <&pm8110_adc_tm>;
qcom,chgr@1000 {
status = "disabled";
reg = <0x1000 0x100>;
interrupts = <0x0 0x10 0x0>,
<0x0 0x10 0x1>,
<0x0 0x10 0x2>,
<0x0 0x10 0x3>,
<0x0 0x10 0x4>,
<0x0 0x10 0x5>,
<0x0 0x10 0x6>,
<0x0 0x10 0x7>;
interrupt-names = "vbat-det-lo",
"vbat-det-hi",
"chgwdog",
"state-change",
"trkl-chg-on",
"fast-chg-on",
"chg-failed",
"chg-done";
};
qcom,buck@1100 {
status = "disabled";
reg = <0x1100 0x100>;
interrupts = <0x0 0x11 0x0>,
<0x0 0x11 0x1>,
<0x0 0x11 0x2>,
<0x0 0x11 0x3>,
<0x0 0x11 0x4>,
<0x0 0x11 0x5>,
<0x0 0x11 0x6>;
interrupt-names = "vbat-ov",
"vreg-ov",
"overtemp",
"vchg-loop",
"ichg-loop",
"ibat-loop",
"vdd-loop";
};
pm8110_chg_batif: qcom,bat-if@1200 {
status = "disabled";
reg = <0x1200 0x100>;
interrupts = <0x0 0x12 0x0>,
<0x0 0x12 0x1>,
<0x0 0x12 0x2>,
<0x0 0x12 0x3>,
<0x0 0x12 0x4>;
interrupt-names = "batt-pres",
"bat-temp-ok",
"bat-fet-on",
"vcp-on",
"psi";
};
qcom,usb-chgpth@1300 {
status = "disabled";
reg = <0x1300 0x100>;
interrupts = <0 0x13 0x0>,
<0 0x13 0x1>,
<0x0 0x13 0x2>,
<0x0 0x13 0x3>;
interrupt-names = "coarse-det-usb",
"usbin-valid",
"chg-gone",
"usb-ocp";
};
qcom,chg-misc@1600 {
status = "disabled";
reg = <0x1600 0x100>;
};
};
pm8110_gpios: gpios {
spmi-dev-container;
compatible = "qcom,qpnp-pin";
gpio-controller;
#gpio-cells = <2>;
#address-cells = <1>;
#size-cells = <1>;
label = "pm8110-gpio";
gpio@c000 {
reg = <0xc000 0x100>;
qcom,pin-num = <1>;
};
gpio@c100 {
reg = <0xc100 0x100>;
qcom,pin-num = <2>;
};
gpio@c200 {
reg = <0xc200 0x100>;
qcom,pin-num = <3>;
};
gpio@c300 {
reg = <0xc300 0x100>;
qcom,pin-num = <4>;
};
};
pm8110_mpps: mpps {
spmi-dev-container;
compatible = "qcom,qpnp-pin";
gpio-controller;
#gpio-cells = <2>;
#address-cells = <1>;
#size-cells = <1>;
label = "pm8110-mpp";
mpp@a000 {
reg = <0xa000 0x100>;
qcom,pin-num = <1>;
};
mpp@a100 {
reg = <0xa100 0x100>;
qcom,pin-num = <2>;
};
mpp@a200 {
reg = <0xa200 0x100>;
qcom,pin-num = <3>;
};
mpp@a300 {
reg = <0xa300 0x100>;
qcom,pin-num = <4>;
};
};
pm8110_vadc: vadc@3100 {
compatible = "qcom,qpnp-vadc";
reg = <0x3100 0x100>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0x0 0x31 0x0>;
interrupt-names = "eoc-int-en-set";
qcom,adc-bit-resolution = <15>;
qcom,adc-vdd-reference = <1800>;
qcom,vadc-poll-eoc;
chan@8 {
label = "die_temp";
reg = <8>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "absolute";
qcom,scale-function = <3>;
qcom,hw-settle-time = <0>;
qcom,fast-avg-setup = <0>;
};
chan@9 {
label = "ref_625mv";
reg = <9>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "absolute";
qcom,scale-function = <0>;
qcom,hw-settle-time = <0>;
qcom,fast-avg-setup = <0>;
};
chan@a {
label = "ref_1250v";
reg = <0xa>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "absolute";
qcom,scale-function = <0>;
qcom,hw-settle-time = <0>;
qcom,fast-avg-setup = <0>;
};
};
pm8110_iadc: iadc@3600 {
compatible = "qcom,qpnp-iadc";
reg = <0x3600 0x100>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0x0 0x36 0x0>;
interrupt-names = "eoc-int-en-set";
qcom,adc-bit-resolution = <16>;
qcom,adc-vdd-reference = <1800>;
qcom,iadc-vadc = <&pm8110_vadc>;
qcom,iadc-poll-eoc;
chan@0 {
label = "internal_rsense";
reg = <0>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <1>;
qcom,calibration-type = "absolute";
qcom,scale-function = <0>;
qcom,hw-settle-time = <0>;
qcom,fast-avg-setup = <0>;
};
};
pm8110_adc_tm: vadc@3400 {
compatible = "qcom,qpnp-adc-tm";
reg = <0x3400 0x100>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0x0 0x34 0x0>,
<0x0 0x34 0x3>,
<0x0 0x34 0x4>;
interrupt-names = "eoc-int-en-set",
"high-thr-en-set",
"low-thr-en-set";
qcom,adc-bit-resolution = <15>;
qcom,adc-vdd-reference = <1800>;
qcom,adc_tm-vadc = <&pm8110_vadc>;
};
qcom,temp-alarm@2400 {
compatible = "qcom,qpnp-temp-alarm";
reg = <0x2400 0x100>;
interrupts = <0x0 0x24 0x0>;
label = "pm8110_tz";
qcom,channel-num = <8>;
qcom,threshold-set = <0>;
qcom,temp_alarm-vadc = <&pm8110_vadc>;
};
pm8110_bms: qcom,bms {
spmi-dev-container;
compatible = "qcom,qpnp-bms";
#address-cells = <1>;
#size-cells = <1>;
status = "disabled";
qcom,r-sense-uohm = <10000>;
qcom,v-cutoff-uv = <3400000>;
qcom,max-voltage-uv = <4200000>;
qcom,r-conn-mohm = <0>;
qcom,shutdown-soc-valid-limit = <100>;
qcom,adjust-soc-low-threshold = <15>;
qcom,ocv-voltage-high-threshold-uv = <3750000>;
qcom,ocv-voltage-low-threshold-uv = <3650000>;
qcom,low-soc-calculate-soc-threshold = <15>;
qcom,low-voltage-calculate-soc-ms = <1000>;
qcom,low-soc-calculate-soc-ms = <5000>;
qcom,calculate-soc-ms = <20000>;
qcom,chg-term-ua = <100000>;
qcom,batt-type = <0>;
qcom,low-voltage-threshold = <3420000>;
qcom,tm-temp-margin = <5000>;
qcom,low-ocv-correction-limit-uv = <100>;
qcom,high-ocv-correction-limit-uv = <250>;
qcom,hold-soc-est = <3>;
qcom,bms-vadc = <&pm8110_vadc>;
qcom,bms-iadc = <&pm8110_iadc>;
qcom,bms-adc_tm = <&pm8110_adc_tm>;
qcom,bms-iadc@3800 {
reg = <0x3800 0x100>;
};
qcom,bms-bms@4000 {
reg = <0x4000 0x100>;
interrupts = <0x0 0x40 0x0>,
<0x0 0x40 0x1>,
<0x0 0x40 0x2>,
<0x0 0x40 0x3>,
<0x0 0x40 0x4>,
<0x0 0x40 0x5>,
<0x0 0x40 0x6>,
<0x0 0x40 0x7>;
interrupt-names = "cc_thr",
"ocv_for_r",
"good_ocv",
"charge_begin",
"ocv_thr",
"sw_cc_thr",
"vsense_avg",
"vsense_for_r";
};
};
qcom,pm8110_rtc {
spmi-dev-container;
compatible = "qcom,qpnp-rtc";
#address-cells = <1>;
#size-cells = <1>;
qcom,qpnp-rtc-write = <0>;
qcom,qpnp-rtc-alarm-pwrup = <0>;
qcom,pm8110_rtc_rw@6000 {
reg = <0x6000 0x100>;
};
qcom,pm8110_rtc_alarm@6100 {
reg = <0x6100 0x100>;
interrupts = <0x0 0x61 0x1>;
};
};
qcom,leds@a100 {
compatible = "qcom,leds-qpnp";
reg = <0xa100 0x100>;
label = "mpp";
};
qcom,leds@a200 {
compatible = "qcom,leds-qpnp";
reg = <0xa200 0x100>;
label = "mpp";
};
};
qcom,pm8110@1 {
spmi-slave-container;
reg = <0x1>;
#address-cells = <1>;
#size-cells = <1>;
regulator@1400 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_s1";
spmi-dev-container;
#address-cells = <1>;
#size-cells = <1>;
reg = <0x1400 0x300>;
status = "disabled";
qcom,ctl@1400 {
reg = <0x1400 0x100>;
};
qcom,ps@1500 {
reg = <0x1500 0x100>;
};
qcom,freq@1600 {
reg = <0x1600 0x100>;
};
};
regulator@1700 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_s2";
spmi-dev-container;
#address-cells = <1>;
#size-cells = <1>;
reg = <0x1700 0x300>;
status = "disabled";
qcom,ctl@1700 {
reg = <0x1700 0x100>;
};
qcom,ps@1800 {
reg = <0x1800 0x100>;
};
qcom,freq@1900 {
reg = <0x1900 0x100>;
};
};
regulator@1a00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_s3";
spmi-dev-container;
#address-cells = <1>;
#size-cells = <1>;
reg = <0x1a00 0x300>;
status = "disabled";
qcom,ctl@1a00 {
reg = <0x1a00 0x100>;
};
qcom,ps@1b00 {
reg = <0x1b00 0x100>;
};
qcom,freq@1c00 {
reg = <0x1c00 0x100>;
};
};
regulator@1d00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_s4";
spmi-dev-container;
#address-cells = <1>;
#size-cells = <1>;
reg = <0x1d00 0x300>;
status = "disabled";
qcom,ctl@1d00 {
reg = <0x1d00 0x100>;
};
qcom,ps@1e00 {
reg = <0x1e00 0x100>;
};
qcom,freq@1f00 {
reg = <0x1f00 0x100>;
};
};
regulator@4000 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l1";
reg = <0x4000 0x100>;
status = "disabled";
};
regulator@4100 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l2";
reg = <0x4100 0x100>;
status = "disabled";
};
regulator@4200 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l3";
reg = <0x4200 0x100>;
status = "disabled";
};
regulator@4300 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l4";
reg = <0x4300 0x100>;
status = "disabled";
};
regulator@4400 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l5";
reg = <0x4400 0x100>;
status = "disabled";
};
regulator@4500 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l6";
reg = <0x4500 0x100>;
status = "disabled";
};
regulator@4600 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l7";
reg = <0x4600 0x100>;
status = "disabled";
};
regulator@4700 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l8";
reg = <0x4700 0x100>;
status = "disabled";
};
regulator@4800 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l9";
reg = <0x4800 0x100>;
status = "disabled";
};
regulator@4900 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l10";
reg = <0x4900 0x100>;
status = "disabled";
};
regulator@4b00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l12";
reg = <0x4b00 0x100>;
status = "disabled";
};
regulator@4d00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l14";
reg = <0x4d00 0x100>;
status = "disabled";
};
regulator@4e00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l15";
reg = <0x4e00 0x100>;
status = "disabled";
};
regulator@4f00 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l16";
reg = <0x4f00 0x100>;
status = "disabled";
};
regulator@5000 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l17";
reg = <0x5000 0x100>;
status = "disabled";
};
regulator@5100 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l18";
reg = <0x5100 0x100>;
status = "disabled";
};
regulator@5200 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l19";
reg = <0x5200 0x100>;
status = "disabled";
};
regulator@5300 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l20";
reg = <0x5300 0x100>;
status = "disabled";
};
regulator@5400 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l21";
reg = <0x5400 0x100>;
status = "disabled";
};
regulator@5500 {
compatible = "qcom,qpnp-regulator";
regulator-name = "8110_l22";
reg = <0x5500 0x100>;
status = "disabled";
};
qcom,vibrator@c000 {
compatible = "qcom,qpnp-vibrator";
reg = <0xc000 0x100>;
label = "vibrator";
status = "disabled";
};
pwm@bc00 {
compatible = "qcom,qpnp-pwm";
reg = <0xbc00 0x100>;
reg-names = "qpnp-lpg-channel-base";
qcom,channel-id = <0>;
};
};
};