libata: PATA driver for Celleb
This is the patch for PATA controller of Celleb.
This driver uses the managed iomap (devres).
Because this driver needs special taskfile accesses, there is
a copy of ata_std_softreset(). ata_dev_try_classify() is exported
so that it can be used in this function.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 4af0a4b..376d2cd 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -562,6 +562,15 @@
If unsure, say N.
+config PATA_SCC
+ tristate "Toshiba's Cell Reference Set IDE support"
+ depends on PCI
+ help
+ This option enables support for the built-in IDE controller on
+ Toshiba Cell Reference Board.
+
+ If unsure, say N.
+
endif
endmenu
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 74298af..13d7397 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -59,6 +59,7 @@
obj-$(CONFIG_PATA_SIS) += pata_sis.o
obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o
obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o
+obj-$(CONFIG_PATA_SCC) += pata_scc.o
obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
# Should be last but one libata driver
obj-$(CONFIG_ATA_GENERIC) += ata_generic.o
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index e900c5e..9c54de5 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -708,7 +708,7 @@
* Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE.
*/
-static unsigned int
+unsigned int
ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err)
{
struct ata_taskfile tf;
@@ -6311,3 +6311,4 @@
EXPORT_SYMBOL_GPL(ata_dummy_irq_on);
EXPORT_SYMBOL_GPL(ata_irq_ack);
EXPORT_SYMBOL_GPL(ata_dummy_irq_ack);
+EXPORT_SYMBOL_GPL(ata_dev_try_classify);
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
new file mode 100644
index 0000000..049a3a2
--- /dev/null
+++ b/drivers/ata/pata_scc.c
@@ -0,0 +1,1228 @@
+/*
+ * Support for IDE interfaces on Celleb platform
+ *
+ * (C) Copyright 2006 TOSHIBA CORPORATION
+ *
+ * This code is based on drivers/ata/ata_piix.c:
+ * Copyright 2003-2005 Red Hat Inc
+ * Copyright 2003-2005 Jeff Garzik
+ * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *
+ * and drivers/ata/ahci.c:
+ * Copyright 2004-2005 Red Hat, Inc.
+ *
+ * and drivers/ata/libata-core.c:
+ * Copyright 2003-2004 Red Hat, Inc. All rights reserved.
+ * Copyright 2003-2004 Jeff Garzik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_scc"
+#define DRV_VERSION "0.1"
+
+#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA 0x01b4
+
+/* PCI BARs */
+#define SCC_CTRL_BAR 0
+#define SCC_BMID_BAR 1
+
+/* offset of CTRL registers */
+#define SCC_CTL_PIOSHT 0x000
+#define SCC_CTL_PIOCT 0x004
+#define SCC_CTL_MDMACT 0x008
+#define SCC_CTL_MCRCST 0x00C
+#define SCC_CTL_SDMACT 0x010
+#define SCC_CTL_SCRCST 0x014
+#define SCC_CTL_UDENVT 0x018
+#define SCC_CTL_TDVHSEL 0x020
+#define SCC_CTL_MODEREG 0x024
+#define SCC_CTL_ECMODE 0xF00
+#define SCC_CTL_MAEA0 0xF50
+#define SCC_CTL_MAEC0 0xF54
+#define SCC_CTL_CCKCTRL 0xFF0
+
+/* offset of BMID registers */
+#define SCC_DMA_CMD 0x000
+#define SCC_DMA_STATUS 0x004
+#define SCC_DMA_TABLE_OFS 0x008
+#define SCC_DMA_INTMASK 0x010
+#define SCC_DMA_INTST 0x014
+#define SCC_DMA_PTERADD 0x018
+#define SCC_REG_CMD_ADDR 0x020
+#define SCC_REG_DATA 0x000
+#define SCC_REG_ERR 0x004
+#define SCC_REG_FEATURE 0x004
+#define SCC_REG_NSECT 0x008
+#define SCC_REG_LBAL 0x00C
+#define SCC_REG_LBAM 0x010
+#define SCC_REG_LBAH 0x014
+#define SCC_REG_DEVICE 0x018
+#define SCC_REG_STATUS 0x01C
+#define SCC_REG_CMD 0x01C
+#define SCC_REG_ALTSTATUS 0x020
+
+/* register value */
+#define TDVHSEL_MASTER 0x00000001
+#define TDVHSEL_SLAVE 0x00000004
+
+#define MODE_JCUSFEN 0x00000080
+
+#define ECMODE_VALUE 0x01
+
+#define CCKCTRL_ATARESET 0x00040000
+#define CCKCTRL_BUFCNT 0x00020000
+#define CCKCTRL_CRST 0x00010000
+#define CCKCTRL_OCLKEN 0x00000100
+#define CCKCTRL_ATACLKOEN 0x00000002
+#define CCKCTRL_LCLKEN 0x00000001
+
+#define QCHCD_IOS_SS 0x00000001
+
+#define QCHSD_STPDIAG 0x00020000
+
+#define INTMASK_MSK 0xD1000012
+#define INTSTS_SERROR 0x80000000
+#define INTSTS_PRERR 0x40000000
+#define INTSTS_RERR 0x10000000
+#define INTSTS_ICERR 0x01000000
+#define INTSTS_BMSINT 0x00000010
+#define INTSTS_BMHE 0x00000008
+#define INTSTS_IOIRQS 0x00000004
+#define INTSTS_INTRQ 0x00000002
+#define INTSTS_ACTEINT 0x00000001
+
+
+/* PIO transfer mode table */
+/* JCHST */
+static const unsigned long JCHSTtbl[2][7] = {
+ {0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00}, /* 100MHz */
+ {0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00} /* 133MHz */
+};
+
+/* JCHHT */
+static const unsigned long JCHHTtbl[2][7] = {
+ {0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00}, /* 100MHz */
+ {0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00} /* 133MHz */
+};
+
+/* JCHCT */
+static const unsigned long JCHCTtbl[2][7] = {
+ {0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00}, /* 100MHz */
+ {0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00} /* 133MHz */
+};
+
+/* DMA transfer mode table */
+/* JCHDCTM/JCHDCTS */
+static const unsigned long JCHDCTxtbl[2][7] = {
+ {0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00}, /* 100MHz */
+ {0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00} /* 133MHz */
+};
+
+/* JCSTWTM/JCSTWTS */
+static const unsigned long JCSTWTxtbl[2][7] = {
+ {0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00}, /* 100MHz */
+ {0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
+};
+
+/* JCTSS */
+static const unsigned long JCTSStbl[2][7] = {
+ {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00}, /* 100MHz */
+ {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05} /* 133MHz */
+};
+
+/* JCENVT */
+static const unsigned long JCENVTtbl[2][7] = {
+ {0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00}, /* 100MHz */
+ {0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
+};
+
+/* JCACTSELS/JCACTSELM */
+static const unsigned long JCACTSELtbl[2][7] = {
+ {0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00}, /* 100MHz */
+ {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01} /* 133MHz */
+};
+
+static const struct pci_device_id scc_pci_tbl[] = {
+ {PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+ { } /* terminate list */
+};
+
+/**
+ * scc_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set PIO mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void scc_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+ void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+ void __iomem *piosht_port = ctrl_base + SCC_CTL_PIOSHT;
+ void __iomem *pioct_port = ctrl_base + SCC_CTL_PIOCT;
+ unsigned long reg;
+ int offset;
+
+ reg = in_be32(cckctrl_port);
+ if (reg & CCKCTRL_ATACLKOEN)
+ offset = 1; /* 133MHz */
+ else
+ offset = 0; /* 100MHz */
+
+ reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
+ out_be32(piosht_port, reg);
+ reg = JCHCTtbl[offset][pio];
+ out_be32(pioct_port, reg);
+}
+
+/**
+ * scc_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ * @udma: udma mode, 0 - 6
+ *
+ * Set UDMA mode for device.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int udma = adev->dma_mode;
+ unsigned int is_slave = (adev->devno != 0);
+ u8 speed = udma;
+ void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+ void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+ void __iomem *mdmact_port = ctrl_base + SCC_CTL_MDMACT;
+ void __iomem *mcrcst_port = ctrl_base + SCC_CTL_MCRCST;
+ void __iomem *sdmact_port = ctrl_base + SCC_CTL_SDMACT;
+ void __iomem *scrcst_port = ctrl_base + SCC_CTL_SCRCST;
+ void __iomem *udenvt_port = ctrl_base + SCC_CTL_UDENVT;
+ void __iomem *tdvhsel_port = ctrl_base + SCC_CTL_TDVHSEL;
+ int offset, idx;
+
+ if (in_be32(cckctrl_port) & CCKCTRL_ATACLKOEN)
+ offset = 1; /* 133MHz */
+ else
+ offset = 0; /* 100MHz */
+
+ if (speed >= XFER_UDMA_0)
+ idx = speed - XFER_UDMA_0;
+ else
+ return;
+
+ if (is_slave) {
+ out_be32(sdmact_port, JCHDCTxtbl[offset][idx]);
+ out_be32(scrcst_port, JCSTWTxtbl[offset][idx]);
+ out_be32(tdvhsel_port,
+ (in_be32(tdvhsel_port) & ~TDVHSEL_SLAVE) | (JCACTSELtbl[offset][idx] << 2));
+ } else {
+ out_be32(mdmact_port, JCHDCTxtbl[offset][idx]);
+ out_be32(mcrcst_port, JCSTWTxtbl[offset][idx]);
+ out_be32(tdvhsel_port,
+ (in_be32(tdvhsel_port) & ~TDVHSEL_MASTER) | JCACTSELtbl[offset][idx]);
+ }
+ out_be32(udenvt_port,
+ JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]);
+}
+
+/**
+ * scc_tf_load - send taskfile registers to host controller
+ * @ap: Port to which output is sent
+ * @tf: ATA taskfile register set
+ *
+ * Note: Original code is ata_tf_load().
+ */
+
+static void scc_tf_load (struct ata_port *ap, const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ out_be32(ioaddr->ctl_addr, tf->ctl);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ out_be32(ioaddr->feature_addr, tf->hob_feature);
+ out_be32(ioaddr->nsect_addr, tf->hob_nsect);
+ out_be32(ioaddr->lbal_addr, tf->hob_lbal);
+ out_be32(ioaddr->lbam_addr, tf->hob_lbam);
+ out_be32(ioaddr->lbah_addr, tf->hob_lbah);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ if (is_addr) {
+ out_be32(ioaddr->feature_addr, tf->feature);
+ out_be32(ioaddr->nsect_addr, tf->nsect);
+ out_be32(ioaddr->lbal_addr, tf->lbal);
+ out_be32(ioaddr->lbam_addr, tf->lbam);
+ out_be32(ioaddr->lbah_addr, tf->lbah);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ out_be32(ioaddr->device_addr, tf->device);
+ VPRINTK("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
+/**
+ * scc_check_status - Read device status reg & clear interrupt
+ * @ap: port where the device is
+ *
+ * Note: Original code is ata_check_status().
+ */
+
+static u8 scc_check_status (struct ata_port *ap)
+{
+ return in_be32(ap->ioaddr.status_addr);
+}
+
+/**
+ * scc_tf_read - input device's ATA taskfile shadow registers
+ * @ap: Port from which input is read
+ * @tf: ATA taskfile register set for storing input
+ *
+ * Note: Original code is ata_tf_read().
+ */
+
+static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ tf->command = scc_check_status(ap);
+ tf->feature = in_be32(ioaddr->error_addr);
+ tf->nsect = in_be32(ioaddr->nsect_addr);
+ tf->lbal = in_be32(ioaddr->lbal_addr);
+ tf->lbam = in_be32(ioaddr->lbam_addr);
+ tf->lbah = in_be32(ioaddr->lbah_addr);
+ tf->device = in_be32(ioaddr->device_addr);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ out_be32(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
+ tf->hob_feature = in_be32(ioaddr->error_addr);
+ tf->hob_nsect = in_be32(ioaddr->nsect_addr);
+ tf->hob_lbal = in_be32(ioaddr->lbal_addr);
+ tf->hob_lbam = in_be32(ioaddr->lbam_addr);
+ tf->hob_lbah = in_be32(ioaddr->lbah_addr);
+ }
+}
+
+/**
+ * scc_exec_command - issue ATA command to host controller
+ * @ap: port to which command is being issued
+ * @tf: ATA taskfile register set
+ *
+ * Note: Original code is ata_exec_command().
+ */
+
+static void scc_exec_command (struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ DPRINTK("ata%u: cmd 0x%X\n", ap->id, tf->command);
+
+ out_be32(ap->ioaddr.command_addr, tf->command);
+ ata_pause(ap);
+}
+
+/**
+ * scc_check_altstatus - Read device alternate status reg
+ * @ap: port where the device is
+ */
+
+static u8 scc_check_altstatus (struct ata_port *ap)
+{
+ return in_be32(ap->ioaddr.altstatus_addr);
+}
+
+/**
+ * scc_std_dev_select - Select device 0/1 on ATA bus
+ * @ap: ATA channel to manipulate
+ * @device: ATA device (numbered from zero) to select
+ *
+ * Note: Original code is ata_std_dev_select().
+ */
+
+static void scc_std_dev_select (struct ata_port *ap, unsigned int device)
+{
+ u8 tmp;
+
+ if (device == 0)
+ tmp = ATA_DEVICE_OBS;
+ else
+ tmp = ATA_DEVICE_OBS | ATA_DEV1;
+
+ out_be32(ap->ioaddr.device_addr, tmp);
+ ata_pause(ap);
+}
+
+/**
+ * scc_bmdma_setup - Set up PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_setup().
+ */
+
+static void scc_bmdma_setup (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u8 dmactl;
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ /* load PRD table addr */
+ out_be32(mmio + SCC_DMA_TABLE_OFS, ap->prd_dma);
+
+ /* specify data direction, triple-check start bit is clear */
+ dmactl = in_be32(mmio + SCC_DMA_CMD);
+ dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
+ if (!rw)
+ dmactl |= ATA_DMA_WR;
+ out_be32(mmio + SCC_DMA_CMD, dmactl);
+
+ /* issue r/w command */
+ ap->ops->exec_command(ap, &qc->tf);
+}
+
+/**
+ * scc_bmdma_start - Start a PCI IDE BMDMA transaction
+ * @qc: Info associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_start().
+ */
+
+static void scc_bmdma_start (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ u8 dmactl;
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ /* start host DMA transaction */
+ dmactl = in_be32(mmio + SCC_DMA_CMD);
+ out_be32(mmio + SCC_DMA_CMD, dmactl | ATA_DMA_START);
+}
+
+/**
+ * scc_devchk - PATA device presence detection
+ * @ap: ATA channel to examine
+ * @device: Device to examine (starting at zero)
+ *
+ * Note: Original code is ata_devchk().
+ */
+
+static unsigned int scc_devchk (struct ata_port *ap,
+ unsigned int device)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 nsect, lbal;
+
+ ap->ops->dev_select(ap, device);
+
+ out_be32(ioaddr->nsect_addr, 0x55);
+ out_be32(ioaddr->lbal_addr, 0xaa);
+
+ out_be32(ioaddr->nsect_addr, 0xaa);
+ out_be32(ioaddr->lbal_addr, 0x55);
+
+ out_be32(ioaddr->nsect_addr, 0x55);
+ out_be32(ioaddr->lbal_addr, 0xaa);
+
+ nsect = in_be32(ioaddr->nsect_addr);
+ lbal = in_be32(ioaddr->lbal_addr);
+
+ if ((nsect == 0x55) && (lbal == 0xaa))
+ return 1; /* we found a device */
+
+ return 0; /* nothing found */
+}
+
+/**
+ * scc_bus_post_reset - PATA device post reset
+ *
+ * Note: Original code is ata_bus_post_reset().
+ */
+
+static void scc_bus_post_reset (struct ata_port *ap, unsigned int devmask)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int dev0 = devmask & (1 << 0);
+ unsigned int dev1 = devmask & (1 << 1);
+ unsigned long timeout;
+
+ /* if device 0 was found in ata_devchk, wait for its
+ * BSY bit to clear
+ */
+ if (dev0)
+ ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+ /* if device 1 was found in ata_devchk, wait for
+ * register access, then wait for BSY to clear
+ */
+ timeout = jiffies + ATA_TMOUT_BOOT;
+ while (dev1) {
+ u8 nsect, lbal;
+
+ ap->ops->dev_select(ap, 1);
+ nsect = in_be32(ioaddr->nsect_addr);
+ lbal = in_be32(ioaddr->lbal_addr);
+ if ((nsect == 1) && (lbal == 1))
+ break;
+ if (time_after(jiffies, timeout)) {
+ dev1 = 0;
+ break;
+ }
+ msleep(50); /* give drive a breather */
+ }
+ if (dev1)
+ ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT);
+
+ /* is all this really necessary? */
+ ap->ops->dev_select(ap, 0);
+ if (dev1)
+ ap->ops->dev_select(ap, 1);
+ if (dev0)
+ ap->ops->dev_select(ap, 0);
+}
+
+/**
+ * scc_bus_softreset - PATA device software reset
+ *
+ * Note: Original code is ata_bus_softreset().
+ */
+
+static unsigned int scc_bus_softreset (struct ata_port *ap,
+ unsigned int devmask)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ DPRINTK("ata%u: bus reset via SRST\n", ap->id);
+
+ /* software reset. causes dev0 to be selected */
+ out_be32(ioaddr->ctl_addr, ap->ctl);
+ udelay(20);
+ out_be32(ioaddr->ctl_addr, ap->ctl | ATA_SRST);
+ udelay(20);
+ out_be32(ioaddr->ctl_addr, ap->ctl);
+
+ /* spec mandates ">= 2ms" before checking status.
+ * We wait 150ms, because that was the magic delay used for
+ * ATAPI devices in Hale Landis's ATADRVR, for the period of time
+ * between when the ATA command register is written, and then
+ * status is checked. Because waiting for "a while" before
+ * checking status is fine, post SRST, we perform this magic
+ * delay here as well.
+ *
+ * Old drivers/ide uses the 2mS rule and then waits for ready
+ */
+ msleep(150);
+
+ /* Before we perform post reset processing we want to see if
+ * the bus shows 0xFF because the odd clown forgets the D7
+ * pulldown resistor.
+ */
+ if (scc_check_status(ap) == 0xFF)
+ return 0;
+
+ scc_bus_post_reset(ap, devmask);
+
+ return 0;
+}
+
+/**
+ * scc_std_softreset - reset host port via ATA SRST
+ * @ap: port to reset
+ * @classes: resulting classes of attached devices
+ *
+ * Note: Original code is ata_std_softreset().
+ */
+
+static int scc_std_softreset (struct ata_port *ap, unsigned int *classes)
+{
+ unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
+ unsigned int devmask = 0, err_mask;
+ u8 err;
+
+ DPRINTK("ENTER\n");
+
+ if (ata_port_offline(ap)) {
+ classes[0] = ATA_DEV_NONE;
+ goto out;
+ }
+
+ /* determine if device 0/1 are present */
+ if (scc_devchk(ap, 0))
+ devmask |= (1 << 0);
+ if (slave_possible && scc_devchk(ap, 1))
+ devmask |= (1 << 1);
+
+ /* select device 0 again */
+ ap->ops->dev_select(ap, 0);
+
+ /* issue bus reset */
+ DPRINTK("about to softreset, devmask=%x\n", devmask);
+ err_mask = scc_bus_softreset(ap, devmask);
+ if (err_mask) {
+ ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n",
+ err_mask);
+ return -EIO;
+ }
+
+ /* determine by signature whether we have ATA or ATAPI devices */
+ classes[0] = ata_dev_try_classify(ap, 0, &err);
+ if (slave_possible && err != 0x81)
+ classes[1] = ata_dev_try_classify(ap, 1, &err);
+
+ out:
+ DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
+ return 0;
+}
+
+/**
+ * scc_bmdma_stop - Stop PCI IDE BMDMA transfer
+ * @qc: Command we are ending DMA for
+ */
+
+static void scc_bmdma_stop (struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
+ void __iomem *bmid_base = ap->host->iomap[SCC_BMID_BAR];
+ u32 reg;
+
+ while (1) {
+ reg = in_be32(bmid_base + SCC_DMA_INTST);
+
+ if (reg & INTSTS_SERROR) {
+ printk(KERN_WARNING "%s: SERROR\n", DRV_NAME);
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_SERROR|INTSTS_BMSINT);
+ out_be32(bmid_base + SCC_DMA_CMD,
+ in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+ continue;
+ }
+
+ if (reg & INTSTS_PRERR) {
+ u32 maea0, maec0;
+ maea0 = in_be32(ctrl_base + SCC_CTL_MAEA0);
+ maec0 = in_be32(ctrl_base + SCC_CTL_MAEC0);
+ printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", DRV_NAME, maea0, maec0);
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_PRERR|INTSTS_BMSINT);
+ out_be32(bmid_base + SCC_DMA_CMD,
+ in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+ continue;
+ }
+
+ if (reg & INTSTS_RERR) {
+ printk(KERN_WARNING "%s: Response Error\n", DRV_NAME);
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_RERR|INTSTS_BMSINT);
+ out_be32(bmid_base + SCC_DMA_CMD,
+ in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+ continue;
+ }
+
+ if (reg & INTSTS_ICERR) {
+ out_be32(bmid_base + SCC_DMA_CMD,
+ in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+ printk(KERN_WARNING "%s: Illegal Configuration\n", DRV_NAME);
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ICERR|INTSTS_BMSINT);
+ continue;
+ }
+
+ if (reg & INTSTS_BMSINT) {
+ unsigned int classes;
+ printk(KERN_WARNING "%s: Internal Bus Error\n", DRV_NAME);
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMSINT);
+ /* TBD: SW reset */
+ scc_std_softreset(ap, &classes);
+ continue;
+ }
+
+ if (reg & INTSTS_BMHE) {
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMHE);
+ continue;
+ }
+
+ if (reg & INTSTS_ACTEINT) {
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ACTEINT);
+ continue;
+ }
+
+ if (reg & INTSTS_IOIRQS) {
+ out_be32(bmid_base + SCC_DMA_INTST, INTSTS_IOIRQS);
+ continue;
+ }
+ break;
+ }
+
+ /* clear start/stop bit */
+ out_be32(bmid_base + SCC_DMA_CMD,
+ in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
+
+ /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+ ata_altstatus(ap); /* dummy read */
+}
+
+/**
+ * scc_bmdma_status - Read PCI IDE BMDMA status
+ * @ap: Port associated with this ATA transaction.
+ */
+
+static u8 scc_bmdma_status (struct ata_port *ap)
+{
+ u8 host_stat;
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ host_stat = in_be32(mmio + SCC_DMA_STATUS);
+
+ /* Workaround for PTERADD: emulate DMA_INTR when
+ * - IDE_STATUS[ERR] = 1
+ * - INT_STATUS[INTRQ] = 1
+ * - DMA_STATUS[IORACTA] = 1
+ */
+ if (!(host_stat & ATA_DMA_INTR)) {
+ u32 int_status = in_be32(mmio + SCC_DMA_INTST);
+ if (ata_altstatus(ap) & ATA_ERR &&
+ int_status & INTSTS_INTRQ &&
+ host_stat & ATA_DMA_ACTIVE)
+ host_stat |= ATA_DMA_INTR;
+ }
+
+ return host_stat;
+}
+
+/**
+ * scc_data_xfer - Transfer data by PIO
+ * @adev: device for this I/O
+ * @buf: data buffer
+ * @buflen: buffer length
+ * @write_data: read/write
+ *
+ * Note: Original code is ata_data_xfer().
+ */
+
+static void scc_data_xfer (struct ata_device *adev, unsigned char *buf,
+ unsigned int buflen, int write_data)
+{
+ struct ata_port *ap = adev->ap;
+ unsigned int words = buflen >> 1;
+ unsigned int i;
+ u16 *buf16 = (u16 *) buf;
+ void __iomem *mmio = ap->ioaddr.data_addr;
+
+ /* Transfer multiple of 2 bytes */
+ if (write_data) {
+ for (i = 0; i < words; i++)
+ out_be32(mmio, cpu_to_le16(buf16[i]));
+ } else {
+ for (i = 0; i < words; i++)
+ buf16[i] = le16_to_cpu(in_be32(mmio));
+ }
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ u16 align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (write_data) {
+ memcpy(align_buf, trailing_buf, 1);
+ out_be32(mmio, cpu_to_le16(align_buf[0]));
+ } else {
+ align_buf[0] = le16_to_cpu(in_be32(mmio));
+ memcpy(trailing_buf, align_buf, 1);
+ }
+ }
+}
+
+/**
+ * scc_irq_on - Enable interrupts on a port.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Note: Original code is ata_irq_on().
+ */
+
+static u8 scc_irq_on (struct ata_port *ap)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 tmp;
+
+ ap->ctl &= ~ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ out_be32(ioaddr->ctl_addr, ap->ctl);
+ tmp = ata_wait_idle(ap);
+
+ ap->ops->irq_clear(ap);
+
+ return tmp;
+}
+
+/**
+ * scc_irq_ack - Acknowledge a device interrupt.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Note: Original code is ata_irq_ack().
+ */
+
+static u8 scc_irq_ack (struct ata_port *ap, unsigned int chk_drq)
+{
+ unsigned int bits = chk_drq ? ATA_BUSY | ATA_DRQ : ATA_BUSY;
+ u8 host_stat, post_stat, status;
+
+ status = ata_busy_wait(ap, bits, 1000);
+ if (status & bits)
+ if (ata_msg_err(ap))
+ printk(KERN_ERR "abnormal status 0x%X\n", status);
+
+ /* get controller status; clear intr, err bits */
+ host_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS);
+ out_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS,
+ host_stat | ATA_DMA_INTR | ATA_DMA_ERR);
+
+ post_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS);
+
+ if (ata_msg_intr(ap))
+ printk(KERN_INFO "%s: irq ack: host_stat 0x%X, new host_stat 0x%X, drv_stat 0x%X\n",
+ __FUNCTION__,
+ host_stat, post_stat, status);
+
+ return status;
+}
+
+/**
+ * scc_bmdma_freeze - Freeze BMDMA controller port
+ * @ap: port to freeze
+ *
+ * Note: Original code is ata_bmdma_freeze().
+ */
+
+static void scc_bmdma_freeze (struct ata_port *ap)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ ap->ctl |= ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ out_be32(ioaddr->ctl_addr, ap->ctl);
+
+ /* Under certain circumstances, some controllers raise IRQ on
+ * ATA_NIEN manipulation. Also, many controllers fail to mask
+ * previously pending IRQ on ATA_NIEN assertion. Clear it.
+ */
+ ata_chk_status(ap);
+
+ ap->ops->irq_clear(ap);
+}
+
+/**
+ * scc_pata_prereset - prepare for reset
+ * @ap: ATA port to be reset
+ */
+
+static int scc_pata_prereset (struct ata_port *ap)
+{
+ ap->cbl = ATA_CBL_PATA80;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * scc_std_postreset - standard postreset callback
+ * @ap: the target ata_port
+ * @classes: classes of attached devices
+ *
+ * Note: Original code is ata_std_postreset().
+ */
+
+static void scc_std_postreset (struct ata_port *ap, unsigned int *classes)
+{
+ DPRINTK("ENTER\n");
+
+ /* re-enable interrupts */
+ if (!ap->ops->error_handler)
+ ap->ops->irq_on(ap);
+
+ /* is double-select really necessary? */
+ if (classes[0] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 1);
+ if (classes[1] != ATA_DEV_NONE)
+ ap->ops->dev_select(ap, 0);
+
+ /* bail out if no device is present */
+ if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
+ DPRINTK("EXIT, no device\n");
+ return;
+ }
+
+ /* set up device control */
+ if (ap->ioaddr.ctl_addr)
+ out_be32(ap->ioaddr.ctl_addr, ap->ctl);
+
+ DPRINTK("EXIT\n");
+}
+
+/**
+ * scc_error_handler - Stock error handler for BMDMA controller
+ * @ap: port to handle error for
+ */
+
+static void scc_error_handler (struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, scc_pata_prereset, scc_std_softreset, NULL,
+ scc_std_postreset);
+}
+
+/**
+ * scc_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * Note: Original code is ata_bmdma_irq_clear().
+ */
+
+static void scc_bmdma_irq_clear (struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ if (!mmio)
+ return;
+
+ out_be32(mmio + SCC_DMA_STATUS, in_be32(mmio + SCC_DMA_STATUS));
+}
+
+/**
+ * scc_port_start - Set port up for dma.
+ * @ap: Port to initialize
+ *
+ * Allocate space for PRD table using ata_port_start().
+ * Set PRD table address for PTERADD. (PRD Transfer End Read)
+ */
+
+static int scc_port_start (struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+ int rc;
+
+ rc = ata_port_start(ap);
+ if (rc)
+ return rc;
+
+ out_be32(mmio + SCC_DMA_PTERADD, ap->prd_dma);
+ return 0;
+}
+
+/**
+ * scc_port_stop - Undo scc_port_start()
+ * @ap: Port to shut down
+ *
+ * Reset PTERADD.
+ */
+
+static void scc_port_stop (struct ata_port *ap)
+{
+ void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+ out_be32(mmio + SCC_DMA_PTERADD, 0);
+}
+
+static struct scsi_host_template scc_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .slave_destroy = ata_scsi_slave_destroy,
+ .bios_param = ata_std_bios_param,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
+};
+
+static const struct ata_port_operations scc_pata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = scc_set_piomode,
+ .set_dmamode = scc_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = scc_tf_load,
+ .tf_read = scc_tf_read,
+ .exec_command = scc_exec_command,
+ .check_status = scc_check_status,
+ .check_altstatus = scc_check_altstatus,
+ .dev_select = scc_std_dev_select,
+
+ .bmdma_setup = scc_bmdma_setup,
+ .bmdma_start = scc_bmdma_start,
+ .bmdma_stop = scc_bmdma_stop,
+ .bmdma_status = scc_bmdma_status,
+ .data_xfer = scc_data_xfer,
+
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+
+ .freeze = scc_bmdma_freeze,
+ .error_handler = scc_error_handler,
+ .post_internal_cmd = scc_bmdma_stop,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = scc_bmdma_irq_clear,
+ .irq_on = scc_irq_on,
+ .irq_ack = scc_irq_ack,
+
+ .port_start = scc_port_start,
+ .port_stop = scc_port_stop,
+};
+
+static struct ata_port_info scc_port_info[] = {
+ {
+ .sht = &scc_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x00,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &scc_pata_ops,
+ },
+};
+
+/**
+ * scc_reset_controller - initialize SCC PATA controller.
+ */
+
+static int scc_reset_controller(struct ata_probe_ent *probe_ent)
+{
+ void __iomem *ctrl_base = probe_ent->iomap[SCC_CTRL_BAR];
+ void __iomem *bmid_base = probe_ent->iomap[SCC_BMID_BAR];
+ void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
+ void __iomem *mode_port = ctrl_base + SCC_CTL_MODEREG;
+ void __iomem *ecmode_port = ctrl_base + SCC_CTL_ECMODE;
+ void __iomem *intmask_port = bmid_base + SCC_DMA_INTMASK;
+ void __iomem *dmastatus_port = bmid_base + SCC_DMA_STATUS;
+ u32 reg = 0;
+
+ out_be32(cckctrl_port, reg);
+ reg |= CCKCTRL_ATACLKOEN;
+ out_be32(cckctrl_port, reg);
+ reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
+ out_be32(cckctrl_port, reg);
+ reg |= CCKCTRL_CRST;
+ out_be32(cckctrl_port, reg);
+
+ for (;;) {
+ reg = in_be32(cckctrl_port);
+ if (reg & CCKCTRL_CRST)
+ break;
+ udelay(5000);
+ }
+
+ reg |= CCKCTRL_ATARESET;
+ out_be32(cckctrl_port, reg);
+ out_be32(ecmode_port, ECMODE_VALUE);
+ out_be32(mode_port, MODE_JCUSFEN);
+ out_be32(intmask_port, INTMASK_MSK);
+
+ if (in_be32(dmastatus_port) & QCHSD_STPDIAG) {
+ printk(KERN_WARNING "%s: failed to detect 80c cable. (PDIAG# is high)\n", DRV_NAME);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+/**
+ * scc_setup_ports - initialize ioaddr with SCC PATA port offsets.
+ * @ioaddr: IO address structure to be initialized
+ * @base: base address of BMID region
+ */
+
+static void scc_setup_ports (struct ata_ioports *ioaddr, void __iomem *base)
+{
+ ioaddr->cmd_addr = base + SCC_REG_CMD_ADDR;
+ ioaddr->altstatus_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
+ ioaddr->ctl_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
+ ioaddr->bmdma_addr = base;
+ ioaddr->data_addr = ioaddr->cmd_addr + SCC_REG_DATA;
+ ioaddr->error_addr = ioaddr->cmd_addr + SCC_REG_ERR;
+ ioaddr->feature_addr = ioaddr->cmd_addr + SCC_REG_FEATURE;
+ ioaddr->nsect_addr = ioaddr->cmd_addr + SCC_REG_NSECT;
+ ioaddr->lbal_addr = ioaddr->cmd_addr + SCC_REG_LBAL;
+ ioaddr->lbam_addr = ioaddr->cmd_addr + SCC_REG_LBAM;
+ ioaddr->lbah_addr = ioaddr->cmd_addr + SCC_REG_LBAH;
+ ioaddr->device_addr = ioaddr->cmd_addr + SCC_REG_DEVICE;
+ ioaddr->status_addr = ioaddr->cmd_addr + SCC_REG_STATUS;
+ ioaddr->command_addr = ioaddr->cmd_addr + SCC_REG_CMD;
+}
+
+static int scc_host_init(struct ata_probe_ent *probe_ent)
+{
+ struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
+ int rc;
+
+ rc = scc_reset_controller(probe_ent);
+ if (rc)
+ return rc;
+
+ probe_ent->n_ports = 1;
+
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ return rc;
+
+ scc_setup_ports(&probe_ent->port[0], probe_ent->iomap[SCC_BMID_BAR]);
+
+ pci_set_master(pdev);
+
+ return 0;
+}
+
+/**
+ * scc_init_one - Register SCC PATA device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in scc_pci_tbl matching with @pdev
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ unsigned int board_idx = (unsigned int) ent->driver_data;
+ struct device *dev = &pdev->dev;
+ struct ata_probe_ent *probe_ent;
+ int rc;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ rc = pcim_iomap_regions(pdev, (1 << SCC_CTRL_BAR) | (1 << SCC_BMID_BAR), DRV_NAME);
+ if (rc == -EBUSY)
+ pcim_pin_device(pdev);
+ if (rc)
+ return rc;
+
+ probe_ent = devm_kzalloc(dev, sizeof(*probe_ent), GFP_KERNEL);
+ if (!probe_ent)
+ return -ENOMEM;
+
+ probe_ent->dev = dev;
+ INIT_LIST_HEAD(&probe_ent->node);
+
+ probe_ent->sht = scc_port_info[board_idx].sht;
+ probe_ent->port_flags = scc_port_info[board_idx].flags;
+ probe_ent->pio_mask = scc_port_info[board_idx].pio_mask;
+ probe_ent->udma_mask = scc_port_info[board_idx].udma_mask;
+ probe_ent->port_ops = scc_port_info[board_idx].port_ops;
+
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = IRQF_SHARED;
+ probe_ent->iomap = pcim_iomap_table(pdev);
+
+ rc = scc_host_init(probe_ent);
+ if (rc)
+ return rc;
+
+ if (!ata_device_add(probe_ent))
+ return -ENODEV;
+
+ devm_kfree(dev, probe_ent);
+ return 0;
+}
+
+static struct pci_driver scc_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = scc_pci_tbl,
+ .probe = scc_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+static int __init scc_init (void)
+{
+ int rc;
+
+ DPRINTK("pci_register_driver\n");
+ rc = pci_register_driver(&scc_pci_driver);
+ if (rc)
+ return rc;
+
+ DPRINTK("done\n");
+ return 0;
+}
+
+static void __exit scc_exit (void)
+{
+ pci_unregister_driver(&scc_pci_driver);
+}
+
+module_init(scc_init);
+module_exit(scc_exit);
+
+MODULE_AUTHOR("Toshiba corp");
+MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 86762a9..60dfc5f 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -759,6 +759,7 @@
extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val,
unsigned long interval_msec,
unsigned long timeout_msec);
+extern unsigned int ata_dev_try_classify(struct ata_port *, unsigned int, u8 *);
/*
* Default driver ops implementations