[PATCH] m68knommu: ColdFire serial driver fixes
Some updates for the old ColdFire serial driver:
. support 3 and 4 UARTs on some ColdFire parts that have them
. enable multifunction pins to serial for 527x CPU's
. support the 5272 UART's fractional baud rate divisor
. switch driver name to "mcfserial"
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
diff --git a/drivers/serial/mcfserial.c b/drivers/serial/mcfserial.c
index aee1b31..3db206d 100644
--- a/drivers/serial/mcfserial.c
+++ b/drivers/serial/mcfserial.c
@@ -60,7 +60,8 @@
#if defined(CONFIG_HW_FEITH)
#define CONSOLE_BAUD_RATE 38400
#define DEFAULT_CBAUD B38400
-#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) || defined(CONFIG_M5329EVB)
+#elif defined(CONFIG_MOD5272) || defined(CONFIG_M5208EVB) || \
+ defined(CONFIG_M5329EVB) || defined(CONFIG_GILBARCO)
#define CONSOLE_BAUD_RATE 115200
#define DEFAULT_CBAUD B115200
#elif defined(CONFIG_ARNEWSH) || defined(CONFIG_FREESCALE) || \
@@ -109,12 +110,30 @@
.irq = IRQBASE,
.flags = ASYNC_BOOT_AUTOCONF,
},
+#ifdef MCFUART_BASE2
{ /* ttyS1 */
.magic = 0,
.addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE2),
.irq = IRQBASE+1,
.flags = ASYNC_BOOT_AUTOCONF,
},
+#endif
+#ifdef MCFUART_BASE3
+ { /* ttyS2 */
+ .magic = 0,
+ .addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE3),
+ .irq = IRQBASE+2,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ },
+#endif
+#ifdef MCFUART_BASE4
+ { /* ttyS3 */
+ .magic = 0,
+ .addr = (volatile unsigned char *) (MCF_MBAR+MCFUART_BASE4),
+ .irq = IRQBASE+3,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ },
+#endif
};
@@ -1516,6 +1535,22 @@
imrp = (volatile unsigned long *) (MCF_MBAR + MCFICM_INTC0 +
MCFINTC_IMRL);
*imrp &= ~((1 << (info->irq - MCFINT_VECBASE)) | 1);
+#if defined(CONFIG_M527x)
+ {
+ /*
+ * External Pin Mask Setting & Enable External Pin for Interface
+ * mrcbis@aliceposta.it
+ */
+ unsigned short *serpin_enable_mask;
+ serpin_enable_mask = (MCF_IPSBAR + MCF_GPIO_PAR_UART);
+ if (info->line == 0)
+ *serpin_enable_mask |= UART0_ENABLE_MASK;
+ else if (info->line == 1)
+ *serpin_enable_mask |= UART1_ENABLE_MASK;
+ else if (info->line == 2)
+ *serpin_enable_mask |= UART2_ENABLE_MASK;
+ }
+#endif
#elif defined(CONFIG_M520x)
volatile unsigned char *icrp, *uartp;
volatile unsigned long *imrp;
@@ -1713,7 +1748,7 @@
/* Initialize the tty_driver structure */
mcfrs_serial_driver->owner = THIS_MODULE;
mcfrs_serial_driver->name = "ttyS";
- mcfrs_serial_driver->driver_name = "serial";
+ mcfrs_serial_driver->driver_name = "mcfserial";
mcfrs_serial_driver->major = TTY_MAJOR;
mcfrs_serial_driver->minor_start = 64;
mcfrs_serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
@@ -1797,10 +1832,23 @@
uartp[MCFUART_UMR] = MCFUART_MR1_PARITYNONE | MCFUART_MR1_CS8;
uartp[MCFUART_UMR] = MCFUART_MR2_STOP1;
+#ifdef CONFIG_M5272
+{
+ /*
+ * For the MCF5272, also compute the baudrate fraction.
+ */
+ int fraction = MCF_BUSCLK - (clk * 32 * mcfrs_console_baud);
+ fraction *= 16;
+ fraction /= (32 * mcfrs_console_baud);
+ uartp[MCFUART_UFPD] = (fraction & 0xf); /* set fraction */
+ clk = (MCF_BUSCLK / mcfrs_console_baud) / 32;
+}
+#else
clk = ((MCF_BUSCLK / mcfrs_console_baud) + 16) / 32; /* set baud */
+#endif
+
uartp[MCFUART_UBG1] = (clk & 0xff00) >> 8; /* set msb baud */
uartp[MCFUART_UBG2] = (clk & 0xff); /* set lsb baud */
-
uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;