wimax: Makefile, Kconfig and docbook linkage for the stack
This patch provides Makefile and KConfig for the WiMAX stack,
integrating them into the networking stack's Makefile, Kconfig and
doc-book templates.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/Documentation/DocBook/networking.tmpl b/Documentation/DocBook/networking.tmpl
index 627707a..59ad69a 100644
--- a/Documentation/DocBook/networking.tmpl
+++ b/Documentation/DocBook/networking.tmpl
@@ -74,6 +74,14 @@
!Enet/sunrpc/rpcb_clnt.c
!Enet/sunrpc/clnt.c
</sect1>
+ <sect1><title>WiMAX</title>
+!Enet/wimax/op-msg.c
+!Enet/wimax/op-reset.c
+!Enet/wimax/op-rfkill.c
+!Enet/wimax/stack.c
+!Iinclude/net/wimax.h
+!Iinclude/linux/wimax.h
+ </sect1>
</chapter>
<chapter id="netdev">
diff --git a/net/Kconfig b/net/Kconfig
index 6ec2cce..bf27760 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -254,6 +254,8 @@
endif # WIRELESS
+source "net/wimax/Kconfig"
+
source "net/rfkill/Kconfig"
source "net/9p/Kconfig"
diff --git a/net/Makefile b/net/Makefile
index ba44604..0fcce89 100644
--- a/net/Makefile
+++ b/net/Makefile
@@ -63,3 +63,4 @@
ifeq ($(CONFIG_NET),y)
obj-$(CONFIG_SYSCTL) += sysctl_net.o
endif
+obj-$(CONFIG_WIMAX) += wimax/
diff --git a/net/wimax/Kconfig b/net/wimax/Kconfig
new file mode 100644
index 0000000..0bdbb69
--- /dev/null
+++ b/net/wimax/Kconfig
@@ -0,0 +1,38 @@
+#
+# WiMAX LAN device configuration
+#
+
+menuconfig WIMAX
+ tristate "WiMAX Wireless Broadband support"
+ help
+
+ Select to configure support for devices that provide
+ wireless broadband connectivity using the WiMAX protocol
+ (IEEE 802.16).
+
+ Please note that most of these devices require signing up
+ for a service plan with a provider.
+
+ The different WiMAX drivers can be enabled in the menu entry
+
+ Device Drivers > Network device support > WiMAX Wireless
+ Broadband devices
+
+ If unsure, it is safe to select M (module).
+
+config WIMAX_DEBUG_LEVEL
+ int "WiMAX debug level"
+ depends on WIMAX
+ default 8
+ help
+
+ Select the maximum debug verbosity level to be compiled into
+ the WiMAX stack code.
+
+ By default, debug messages are disabled at runtime and can
+ be selectively enabled for different parts of the code using
+ the sysfs debug-levels file.
+
+ If set at zero, this will compile out all the debug code.
+
+ It is recommended that it is left at 8.
diff --git a/net/wimax/Makefile b/net/wimax/Makefile
new file mode 100644
index 0000000..5b80b94
--- /dev/null
+++ b/net/wimax/Makefile
@@ -0,0 +1,13 @@
+
+obj-$(CONFIG_WIMAX) += wimax.o
+
+wimax-y := \
+ id-table.o \
+ op-msg.o \
+ op-reset.o \
+ op-rfkill.o \
+ stack.o
+
+wimax-$(CONFIG_DEBUG_FS) += debugfs.o
+
+