Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (27 commits)
alim15x3: remove redundant m5229_revision check
sc1200: fix ->dma_base equal zero handling
cs5520: fix ->dma_base equal zero handling
sgiioc4: add missing ->dma_base check
cs5535: add missing ->dma_base check
ide: remove CONFIG_IDEDMA_IVB config option
ide: change master/slave IDENTIFY order
ide: move ide_config_drive_speed() calls to upper layers (take 2)
pdc202xx_new: check ide_config_drive_speed() return value
cs5535: check ide_config_drive_speed() return value
amd74xx/via82cxxx: check ide_config_drive_speed() return value
au1xxx: fix au1xxx_set_pio_mode()
icside: use ide_tune_dma()
ide-pmac: fix PIO setup and enable autotune
ide-pmac: use ide_tune_dma() (take 2)
ide-pmac: remove pmac_ide_do_setfeature() (take 2)
ide-pmac: remove nIEN clearing from pmac_ide_do_setfeature()
ide-pmac: use __ide_wait_stat()
ide-pmac: remove extra good status wait from pmac_ide_do_setfeature()
ide: add __ide_wait_stat() helper
...
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index aa0e0c9..8982c09 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1074,22 +1074,6 @@
config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
-config IDEDMA_IVB
- bool "IGNORE word93 Validation BITS"
- depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
- ---help---
- There are unclear terms in ATA-4 and ATA-5 standards how certain
- hardware (an 80c ribbon) should be detected. Different interpretations
- of the standards have been released in hardware. This causes problems:
- for example, a host with Ultra Mode 4 (or higher) will not run
- in that mode with an 80c ribbon.
-
- If you are experiencing compatibility or performance problems, you
- MAY try to answer Y here. However, it does not necessarily solve
- any of your problems, it could even cause more of them.
-
- It is normally safe to answer Y; however, the default is N.
-
endif
config BLK_DEV_HD_ONLY
diff --git a/drivers/ide/arm/icside.c b/drivers/ide/arm/icside.c
index 7912a47..bd1f5b6 100644
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -248,7 +248,7 @@
* MW1 80 50 50 150 C
* MW2 70 25 25 120 C
*/
-static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
+static void icside_set_dma_mode(ide_drive_t *drive, const u8 xfer_mode)
{
int cycle_time, use_dma_info = 0;
@@ -273,7 +273,7 @@
cycle_time = 480;
break;
default:
- return 1;
+ return;
}
/*
@@ -287,8 +287,6 @@
printk("%s: %s selected (peak %dMB/s)\n", drive->name,
ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
-
- return ide_config_drive_speed(drive, xfer_mode);
}
static void icside_dma_host_off(ide_drive_t *drive)
@@ -313,41 +311,10 @@
static int icside_dma_check(ide_drive_t *drive)
{
- struct hd_driveid *id = drive->id;
- ide_hwif_t *hwif = HWIF(drive);
- int xfer_mode = 0;
+ if (ide_tune_dma(drive))
+ return 0;
- if (!(id->capability & 1) || !hwif->autodma)
- goto out;
-
- /*
- * Consult the list of known "bad" drives
- */
- if (__ide_dma_bad_drive(drive))
- goto out;
-
- /*
- * Enable DMA on any drive that has multiword DMA
- */
- if (id->field_valid & 2) {
- xfer_mode = ide_max_dma_mode(drive);
- goto out;
- }
-
- /*
- * Consult the list of known "good" drives
- */
- if (__ide_dma_good_drive(drive)) {
- if (id->eide_dma_time > 150)
- goto out;
- xfer_mode = XFER_MW_DMA_1;
- }
-
-out:
- if (xfer_mode == 0)
- return -1;
-
- return icside_set_speed(drive, xfer_mode) ? -1 : 0;
+ return -1;
}
static int icside_dma_end(ide_drive_t *drive)
@@ -464,7 +431,7 @@
hwif->dmatable_cpu = NULL;
hwif->dmatable_dma = 0;
- hwif->speedproc = icside_set_speed;
+ hwif->set_dma_mode = icside_set_dma_mode;
hwif->autodma = 1;
hwif->ide_dma_check = icside_dma_check;
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
index 4bb42b3..2b4d2a0 100644
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -716,11 +716,9 @@
}
cris_ide_set_speed(TYPE_PIO, setup, strobe, hold);
-
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
-static int speed_cris_ide(ide_drive_t *drive, const u8 speed)
+static void cris_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
int cyc = 0, dvs = 0, strobe = 0, hold = 0;
@@ -759,8 +757,6 @@
cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0);
else
cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
-
- return ide_config_drive_speed(drive, speed);
}
void __init
@@ -791,7 +787,7 @@
hwif->mmio = 1;
hwif->chipset = ide_etrax100;
hwif->set_pio_mode = &cris_set_pio_mode;
- hwif->speedproc = &speed_cris_ide;
+ hwif->set_dma_mode = &cris_set_dma_mode;
hwif->ata_input_data = &cris_ide_input_data;
hwif->ata_output_data = &cris_ide_output_data;
hwif->atapi_input_bytes = &cris_atapi_input_bytes;
diff --git a/drivers/ide/ide-acpi.c b/drivers/ide/ide-acpi.c
index 6bff81a..1d5f682 100644
--- a/drivers/ide/ide-acpi.c
+++ b/drivers/ide/ide-acpi.c
@@ -649,7 +649,6 @@
if (!on)
acpi_bus_set_power(hwif->acpidata->obj_handle, ACPI_STATE_D3);
}
-EXPORT_SYMBOL_GPL(ide_acpi_set_state);
/**
* ide_acpi_init - initialize the ACPI link for an IDE interface
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 6000c08..b453211 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -169,6 +169,11 @@
EXPORT_SYMBOL_GPL(ide_dma_intr);
+static int ide_dma_good_drive(ide_drive_t *drive)
+{
+ return ide_in_drive_list(drive->id, drive_whitelist);
+}
+
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
/**
* ide_build_sglist - map IDE scatter gather for DMA I/O
@@ -357,7 +362,7 @@
return 0;
/* Consult the list of known "good" drives */
- if (__ide_dma_good_drive(drive))
+ if (ide_dma_good_drive(drive))
return 0;
}
@@ -639,14 +644,6 @@
EXPORT_SYMBOL(__ide_dma_bad_drive);
-int __ide_dma_good_drive (ide_drive_t *drive)
-{
- struct hd_driveid *id = drive->id;
- return ide_in_drive_list(id, drive_whitelist);
-}
-
-EXPORT_SYMBOL(__ide_dma_good_drive);
-
static const u8 xfer_mode_bases[] = {
XFER_UDMA_0,
XFER_MW_DMA_0,
@@ -746,6 +743,14 @@
}
}
+ if (hwif->chipset == ide_acorn && mode == 0) {
+ /*
+ * is this correct?
+ */
+ if (ide_dma_good_drive(drive) && drive->id->eide_dma_time < 150)
+ mode = XFER_MW_DMA_1;
+ }
+
printk(KERN_DEBUG "%s: selected mode 0x%x\n", drive->name, mode);
return min(mode, req_mode);
@@ -769,7 +774,10 @@
if (!speed)
return 0;
- if (drive->hwif->speedproc(drive, speed))
+ if (drive->hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
+ return 0;
+
+ if (ide_set_dma_mode(drive, speed))
return 0;
return 1;
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 9560a8f..4cece93 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -836,9 +836,17 @@
if (set_pio_mode_abuse(drive->hwif, req_pio)) {
if (hwif->set_pio_mode)
hwif->set_pio_mode(drive, req_pio);
- } else
+ } else {
+ int keep_dma = drive->using_dma;
+
ide_set_pio(drive, req_pio);
+ if (hwif->host_flags & IDE_HFLAG_SET_PIO_MODE_KEEP_DMA) {
+ if (keep_dma)
+ hwif->ide_dma_on(drive);
+ }
+ }
+
return ide_stopped;
} else {
if (drive->media == ide_disk)
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index cf0678b..aa73883 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -473,57 +473,22 @@
EXPORT_SYMBOL(drive_is_ready);
/*
- * Global for All, and taken from ide-pmac.c. Can be called
- * with spinlock held & IRQs disabled, so don't schedule !
- */
-int wait_for_ready (ide_drive_t *drive, int timeout)
-{
- ide_hwif_t *hwif = HWIF(drive);
- u8 stat = 0;
-
- while(--timeout) {
- stat = hwif->INB(IDE_STATUS_REG);
- if (!(stat & BUSY_STAT)) {
- if (drive->ready_stat == 0)
- break;
- else if ((stat & drive->ready_stat)||(stat & ERR_STAT))
- break;
- }
- mdelay(1);
- }
- if ((stat & ERR_STAT) || timeout <= 0) {
- if (stat & ERR_STAT) {
- printk(KERN_ERR "%s: wait_for_ready, "
- "error status: %x\n", drive->name, stat);
- }
- return 1;
- }
- return 0;
-}
-
-/*
* This routine busy-waits for the drive status to be not "busy".
* It then checks the status for all of the "good" bits and none
* of the "bad" bits, and if all is okay it returns 0. All other
- * cases return 1 after invoking ide_error() -- caller should just return.
+ * cases return error -- caller may then invoke ide_error().
*
* This routine should get fixed to not hog the cpu during extra long waits..
* That could be done by busy-waiting for the first jiffy or two, and then
* setting a timer to wake up at half second intervals thereafter,
* until timeout is achieved, before timing out.
*/
-int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+static int __ide_wait_stat(ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout, u8 *rstat)
{
- ide_hwif_t *hwif = HWIF(drive);
- u8 stat;
- int i;
+ ide_hwif_t *hwif = drive->hwif;
unsigned long flags;
-
- /* bail early if we've exceeded max_failures */
- if (drive->max_failures && (drive->failures > drive->max_failures)) {
- *startstop = ide_stopped;
- return 1;
- }
+ int i;
+ u8 stat;
udelay(1); /* spec allows drive 400ns to assert "BUSY" */
if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
@@ -541,8 +506,8 @@
break;
local_irq_restore(flags);
- *startstop = ide_error(drive, "status timeout", stat);
- return 1;
+ *rstat = stat;
+ return -EBUSY;
}
}
local_irq_restore(flags);
@@ -556,11 +521,39 @@
*/
for (i = 0; i < 10; i++) {
udelay(1);
- if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad))
+ if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad)) {
+ *rstat = stat;
return 0;
+ }
}
- *startstop = ide_error(drive, "status error", stat);
- return 1;
+ *rstat = stat;
+ return -EFAULT;
+}
+
+/*
+ * In case of error returns error value after doing "*startstop = ide_error()".
+ * The caller should return the updated value of "startstop" in this case,
+ * "startstop" is unchanged when the function returns 0.
+ */
+int ide_wait_stat(ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+{
+ int err;
+ u8 stat;
+
+ /* bail early if we've exceeded max_failures */
+ if (drive->max_failures && (drive->failures > drive->max_failures)) {
+ *startstop = ide_stopped;
+ return 1;
+ }
+
+ err = __ide_wait_stat(drive, good, bad, timeout, &stat);
+
+ if (err) {
+ char *s = (err == -EBUSY) ? "status timeout" : "status error";
+ *startstop = ide_error(drive, s, stat);
+ }
+
+ return err;
}
EXPORT_SYMBOL(ide_wait_stat);
@@ -620,15 +613,10 @@
/*
* FIXME:
- * - change master/slave IDENTIFY order
* - force bit13 (80c cable present) check also for !ivb devices
* (unless the slave device is pre-ATA3)
*/
-#ifndef CONFIG_IDEDMA_IVB
if ((id->hw_config & 0x4000) || (ivb && (id->hw_config & 0x2000)))
-#else
- if (id->hw_config & 0x6000)
-#endif
return 1;
no_80w:
@@ -778,15 +766,10 @@
#endif
}
-/*
- * Similar to ide_wait_stat(), except it never calls ide_error internally.
- *
- * const char *msg == consider adding for verbose errors.
- */
-int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
+int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
{
- ide_hwif_t *hwif = HWIF(drive);
- int i, error = 1;
+ ide_hwif_t *hwif = drive->hwif;
+ int error;
u8 stat;
// while (HWGROUP(drive)->busy)
@@ -826,35 +809,10 @@
hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
if ((IDE_CONTROL_REG) && (drive->quirk_list == 2))
hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
- udelay(1);
- /*
- * Wait for drive to become non-BUSY
- */
- if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
- unsigned long flags, timeout;
- local_irq_set(flags);
- timeout = jiffies + WAIT_CMD;
- while ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
- if (time_after(jiffies, timeout))
- break;
- }
- local_irq_restore(flags);
- }
- /*
- * Allow status to settle, then read it again.
- * A few rare drives vastly violate the 400ns spec here,
- * so we'll wait up to 10usec for a "good" status
- * rather than expensively fail things immediately.
- * This fix courtesy of Matthew Faupel & Niccolo Rigacci.
- */
- for (i = 0; i < 10; i++) {
- udelay(1);
- if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), drive->ready_stat, BUSY_STAT|DRQ_STAT|ERR_STAT)) {
- error = 0;
- break;
- }
- }
+ error = __ide_wait_stat(drive, drive->ready_stat,
+ BUSY_STAT|DRQ_STAT|ERR_STAT,
+ WAIT_CMD, &stat);
SELECT_MASK(drive, 0);
@@ -899,9 +857,6 @@
return error;
}
-EXPORT_SYMBOL(ide_config_drive_speed);
-
-
/*
* This should get invoked any time we exit the driver to
* wait for an interrupt response from a drive. handler() points
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index d97390c..0e2562f 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -349,7 +349,7 @@
drive->name, host_pio, req_pio,
req_pio == 255 ? "(auto-tune)" : "", pio);
- hwif->set_pio_mode(drive, pio);
+ (void)ide_set_pio_mode(drive, XFER_PIO_0 + pio);
}
EXPORT_SYMBOL_GPL(ide_set_pio);
@@ -378,39 +378,83 @@
blk_queue_bounce_limit(drive->queue, addr);
}
+int ide_set_pio_mode(ide_drive_t *drive, const u8 mode)
+{
+ ide_hwif_t *hwif = drive->hwif;
+
+ if (hwif->set_pio_mode == NULL)
+ return -1;
+
+ /*
+ * TODO: temporary hack for some legacy host drivers that didn't
+ * set transfer mode on the device in ->set_pio_mode method...
+ */
+ if (hwif->set_dma_mode == NULL) {
+ hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ return 0;
+ }
+
+ if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
+ if (ide_config_drive_speed(drive, mode))
+ return -1;
+ hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ return 0;
+ } else {
+ hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+ return ide_config_drive_speed(drive, mode);
+ }
+}
+
+int ide_set_dma_mode(ide_drive_t *drive, const u8 mode)
+{
+ ide_hwif_t *hwif = drive->hwif;
+
+ if (hwif->set_dma_mode == NULL)
+ return -1;
+
+ if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
+ if (ide_config_drive_speed(drive, mode))
+ return -1;
+ hwif->set_dma_mode(drive, mode);
+ return 0;
+ } else {
+ hwif->set_dma_mode(drive, mode);
+ return ide_config_drive_speed(drive, mode);
+ }
+}
+
+EXPORT_SYMBOL_GPL(ide_set_dma_mode);
+
/**
* ide_set_xfer_rate - set transfer rate
* @drive: drive to set
- * @speed: speed to attempt to set
+ * @rate: speed to attempt to set
*
* General helper for setting the speed of an IDE device. This
* function knows about user enforced limits from the configuration
- * which speedproc() does not. High level drivers should never
- * invoke speedproc() directly.
+ * which ->set_pio_mode/->set_dma_mode does not.
*/
-
+
int ide_set_xfer_rate(ide_drive_t *drive, u8 rate)
{
ide_hwif_t *hwif = drive->hwif;
- if (hwif->speedproc == NULL)
+ if (hwif->set_dma_mode == NULL)
return -1;
rate = ide_rate_filter(drive, rate);
- if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5) {
- if (hwif->set_pio_mode)
- hwif->set_pio_mode(drive, rate - XFER_PIO_0);
+ if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5)
+ return ide_set_pio_mode(drive, rate);
- /*
- * FIXME: this is incorrect to return zero here but
- * since all users of ide_set_xfer_rate() ignore
- * the return value it is not a problem currently
- */
- return 0;
- }
+ /*
+ * TODO: transfer modes 0x00-0x07 passed from the user-space are
+ * currently handled here which needs fixing (please note that such
+ * case could happen iff the transfer mode has already been set on
+ * the device by ide-proc.c::set_xfer_rate()).
+ */
- return hwif->speedproc(drive, rate);
+ return ide_set_dma_mode(drive, rate);
}
static void ide_dump_opcode(ide_drive_t *drive)
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index b4c9f63..d101171 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -719,9 +719,9 @@
*/
static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
{
- unsigned int unit;
unsigned long flags;
unsigned int irqd;
+ int unit;
if (hwif->noprobe)
return;
@@ -777,10 +777,9 @@
printk(KERN_DEBUG "%s: Wait for ready failed before probe !\n", hwif->name);
/*
- * Second drive should only exist if first drive was found,
- * but a lot of cdrom drives are configured as single slaves.
+ * Need to probe slave device first to make it release PDIAG-.
*/
- for (unit = 0; unit < MAX_DRIVES; ++unit) {
+ for (unit = MAX_DRIVES - 1; unit >= 0; unit--) {
ide_drive_t *drive = &hwif->drives[unit];
drive->dn = (hwif->channel ? 2 : 0) + unit;
(void) probe_for_drive(drive);
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index a96a8b1..5c0e407 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -397,7 +397,7 @@
#endif
hwif->set_pio_mode = tmp_hwif->set_pio_mode;
- hwif->speedproc = tmp_hwif->speedproc;
+ hwif->set_dma_mode = tmp_hwif->set_dma_mode;
hwif->mdma_filter = tmp_hwif->mdma_filter;
hwif->udma_filter = tmp_hwif->udma_filter;
hwif->selectproc = tmp_hwif->selectproc;
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index ccfb989..b992b2b 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -65,7 +65,7 @@
hwif->hw.irq = hwif->irq = irq;
hwif->hw.dma = NO_DMA;
- hwif->hw.chipset = ide_generic;
+ hwif->chipset = hwif->hw.chipset = ide_generic;
if (mmio) {
hwif->mmio = 1;
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index 85819ae..aebde49 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -101,12 +101,7 @@
static void au1xxx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- int mem_sttime;
- int mem_stcfg;
- u8 speed;
-
- mem_sttime = 0;
- mem_stcfg = au_readl(MEM_STCFG2);
+ int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
/* set pio mode! */
switch(pio) {
@@ -164,18 +159,11 @@
au_writel(mem_sttime,MEM_STTIME2);
au_writel(mem_stcfg,MEM_STCFG2);
-
- speed = pio + XFER_PIO_0;
- ide_config_drive_speed(drive, speed);
}
-static int auide_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void auide_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
- int mem_sttime;
- int mem_stcfg;
-
- mem_sttime = 0;
- mem_stcfg = au_readl(MEM_STCFG2);
+ int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
switch(speed) {
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
@@ -211,16 +199,11 @@
break;
#endif
default:
- return 1;
+ return;
}
- if (ide_config_drive_speed(drive, speed))
- return 1;
-
au_writel(mem_sttime,MEM_STTIME2);
au_writel(mem_stcfg,MEM_STCFG2);
-
- return 0;
}
/*
@@ -682,6 +665,7 @@
#endif
hwif->pio_mask = ATA_PIO4;
+ hwif->host_flags = IDE_HFLAG_POST_SET_MODE;
hwif->noprobe = 0;
hwif->drives[0].unmask = 1;
@@ -702,7 +686,7 @@
#endif
hwif->set_pio_mode = &au1xxx_set_pio_mode;
- hwif->speedproc = &auide_tune_chipset;
+ hwif->set_dma_mode = &auide_set_dma_mode;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
hwif->dma_off_quietly = &auide_dma_off_quietly;
diff --git a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c
index 0d5f62c..d6cb2d5 100644
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -87,7 +87,7 @@
return chipset_table->ultra_settings;
}
-static int aec6210_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void aec6210_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -111,10 +111,9 @@
tmp2 = ((ultra_conf << (2*drive->dn)) | (tmp1 & ~(3 << (2*drive->dn))));
pci_write_config_byte(dev, 0x54, tmp2);
local_irq_restore(flags);
- return(ide_config_drive_speed(drive, speed));
}
-static int aec6260_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void aec6260_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -135,12 +134,11 @@
tmp2 = ((ultra_conf << (4*unit)) | (tmp1 & ~(7 << (4*unit))));
pci_write_config_byte(dev, (0x44|hwif->channel), tmp2);
local_irq_restore(flags);
- return(ide_config_drive_speed(drive, speed));
}
static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void) HWIF(drive)->speedproc(drive, pio + XFER_PIO_0);
+ drive->hwif->set_dma_mode(drive, pio + XFER_PIO_0);
}
static int aec62xx_config_drive_xfer_rate (ide_drive_t *drive)
@@ -205,9 +203,9 @@
if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
if(hwif->mate)
hwif->mate->serialized = hwif->serialized = 1;
- hwif->speedproc = &aec6210_tune_chipset;
+ hwif->set_dma_mode = &aec6210_set_mode;
} else
- hwif->speedproc = &aec6260_tune_chipset;
+ hwif->set_dma_mode = &aec6260_set_mode;
if (!hwif->dma_base) {
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index d04b966..0b83443 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -283,14 +283,14 @@
#endif /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
/**
- * ali_tune_pio - set host controller for PIO mode
+ * ali_set_pio_mode - set host controller for PIO mode
* @drive: drive
* @pio: PIO mode number
*
* Program the controller for the given PIO mode.
*/
-static void ali_tune_pio(ide_drive_t *drive, const u8 pio)
+static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -358,21 +358,6 @@
}
/**
- * ali_set_pio_mode - set up drive for PIO mode
- * @drive: drive to tune
- * @pio: desired mode
- *
- * Program the controller with the desired PIO timing for the given drive.
- * Then set up the drive itself.
- */
-
-static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- ali_tune_pio(drive, pio);
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-/**
* ali_udma_filter - compute UDMA mask
* @drive: IDE device
*
@@ -401,15 +386,14 @@
}
/**
- * ali15x3_tune_chipset - set up chipset/drive for new speed
- * @drive: drive to configure for
- * @speed: desired speed
+ * ali_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
* Configure the hardware for the desired IDE transfer mode.
- * We also do the needed drive configuration through helpers
*/
-static int ali15x3_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -419,7 +403,7 @@
int m5229_udma = (hwif->channel) ? 0x57 : 0x56;
if (speed < XFER_PIO_0)
- return 1;
+ return;
if (speed == XFER_UDMA_6)
speed1 = 0x47;
@@ -450,7 +434,6 @@
pci_write_config_byte(dev, 0x4b, tmpbyte);
}
}
- return (ide_config_drive_speed(drive, speed));
}
/**
@@ -699,7 +682,7 @@
{
hwif->autodma = 0;
hwif->set_pio_mode = &ali_set_pio_mode;
- hwif->speedproc = &ali15x3_tune_chipset;
+ hwif->set_dma_mode = &ali_set_dma_mode;
hwif->udma_filter = &ali_udma_filter;
/* don't use LBA48 DMA on ALi devices before rev 0xC5 */
@@ -711,6 +694,10 @@
return;
}
+ /*
+ * check in ->init_dma guarantees m5229_revision >= 0x20 here
+ */
+
if (m5229_revision > 0x20)
hwif->atapi_dma = 1;
@@ -728,18 +715,15 @@
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x07;
- if (m5229_revision >= 0x20) {
- /*
- * M1543C or newer for DMAing
- */
- hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
- hwif->dma_setup = &ali15x3_dma_setup;
- if (!noautodma)
- hwif->autodma = 1;
+ hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
+ hwif->dma_setup = &ali15x3_dma_setup;
- if (hwif->cbl != ATA_CBL_PATA40_SHORT)
- hwif->cbl = ata66_ali15x3(hwif);
- }
+ if (hwif->cbl != ATA_CBL_PATA40_SHORT)
+ hwif->cbl = ata66_ali15x3(hwif);
+
+ if (!noautodma)
+ hwif->autodma = 1;
+
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
diff --git a/drivers/ide/pci/amd74xx.c b/drivers/ide/pci/amd74xx.c
index 513205e..6ff4089 100644
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -1,5 +1,5 @@
/*
- * Version 2.22
+ * Version 2.23
*
* AMD 755/756/766/8111 and nVidia nForce/2/2s/3/3s/CK804/MCP04
* IDE driver for Linux.
@@ -229,20 +229,16 @@
}
/*
- * amd_set_drive() computes timing values configures the drive and
- * the chipset to a desired transfer mode. It also can be called
- * by upper layers.
+ * amd_set_drive() computes timing values and configures the chipset
+ * to a desired transfer mode. It also can be called by upper layers.
*/
-static int amd_set_drive(ide_drive_t *drive, const u8 speed)
+static void amd_set_drive(ide_drive_t *drive, const u8 speed)
{
ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
struct ide_timing t, p;
int T, UT;
- if (speed != XFER_PIO_SLOW)
- ide_config_drive_speed(drive, speed);
-
T = 1000000000 / amd_clock;
UT = (amd_config->udma_mask == ATA_UDMA2) ? T : (T / 2);
@@ -257,12 +253,6 @@
if (speed == XFER_UDMA_6 && amd_clock <= 33333) t.udma = 15;
amd_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);
-
- if (!drive->init_speed)
- drive->init_speed = speed;
- drive->current_speed = speed;
-
- return 0;
}
/*
@@ -399,7 +389,7 @@
hwif->autodma = 0;
hwif->set_pio_mode = &amd_set_pio_mode;
- hwif->speedproc = &amd_set_drive;
+ hwif->set_dma_mode = &amd_set_drive;
for (i = 0; i < 2; i++) {
hwif->drives[i].io_32bit = 1;
@@ -441,7 +431,8 @@
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
.bootable = ON_BOARD, \
.host_flags = IDE_HFLAG_PIO_NO_BLACKLIST \
- | IDE_HFLAG_PIO_NO_DOWNGRADE, \
+ | IDE_HFLAG_PIO_NO_DOWNGRADE \
+ | IDE_HFLAG_POST_SET_MODE, \
.pio_mask = ATA_PIO5, \
}
@@ -454,7 +445,8 @@
.enablebits = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \
.bootable = ON_BOARD, \
.host_flags = IDE_HFLAG_PIO_NO_BLACKLIST \
- | IDE_HFLAG_PIO_NO_DOWNGRADE, \
+ | IDE_HFLAG_PIO_NO_DOWNGRADE \
+ | IDE_HFLAG_POST_SET_MODE, \
.pio_mask = ATA_PIO5, \
}
diff --git a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c
index 178876a..0eb97f0 100644
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -122,14 +122,14 @@
}
/**
- * atiixp_tune_pio - tune a drive attached to a ATIIXP
- * @drive: drive to tune
- * @pio: desired PIO mode
+ * atiixp_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Set the interface PIO mode.
*/
-static void atiixp_tune_pio(ide_drive_t *drive, u8 pio)
+static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
struct pci_dev *dev = drive->hwif->pci_dev;
unsigned long flags;
@@ -153,23 +153,16 @@
spin_unlock_irqrestore(&atiixp_lock, flags);
}
-static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- atiixp_tune_pio(drive, pio);
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
/**
- * atiixp_tune_chipset - tune a ATIIXP interface
- * @drive: IDE drive to tune
- * @speed: speed to configure
+ * atiixp_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Set a ATIIXP interface channel to the desired speeds. This involves
- * requires the right timing data into the ATIIXP configuration space
- * then setting the drive parameters appropriately
+ * Set a ATIIXP host controller to the desired DMA mode. This involves
+ * programming the right timing data into the PCI configuration space.
*/
-static int atiixp_speedproc(ide_drive_t *drive, const u8 speed)
+static void atiixp_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
struct pci_dev *dev = drive->hwif->pci_dev;
unsigned long flags;
@@ -204,9 +197,7 @@
else
pio = speed - XFER_PIO_0;
- atiixp_tune_pio(drive, pio);
-
- return ide_config_drive_speed(drive, speed);
+ atiixp_set_pio_mode(drive, pio);
}
/**
@@ -249,7 +240,7 @@
hwif->autodma = 0;
hwif->set_pio_mode = &atiixp_set_pio_mode;
- hwif->speedproc = &atiixp_speedproc;
+ hwif->set_dma_mode = &atiixp_set_dma_mode;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 0b568c6..d50f15e 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -280,10 +280,9 @@
return;
cmd64x_tune_pio(drive, pio);
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
-static int cmd64x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -324,13 +323,11 @@
program_cycle_times(drive, 480, 215);
break;
default:
- return 1;
+ return;
}
if (speed >= XFER_SW_DMA_0)
(void) pci_write_config_byte(dev, pciU, regU);
-
- return ide_config_drive_speed(drive, speed);
}
static int cmd64x_config_drive_for_dma (ide_drive_t *drive)
@@ -524,7 +521,7 @@
pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
hwif->set_pio_mode = &cmd64x_set_pio_mode;
- hwif->speedproc = &cmd64x_tune_chipset;
+ hwif->set_dma_mode = &cmd64x_set_dma_mode;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index 1217d2a..fbce900 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -96,22 +96,13 @@
reg = inb(hwif->dma_base + 0x02 + 8*controller);
reg |= 1<<((drive->dn&1)+5);
outb(reg, hwif->dma_base + 0x02 + 8*controller);
-
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
-static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
printk(KERN_ERR "cs55x0: bad ide timing.\n");
cs5520_set_pio_mode(drive, 0);
-
- /*
- * FIXME: this is incorrect to return zero here but
- * since all users of ide_set_xfer_rate() ignore
- * the return value it is not a problem currently
- */
- return 0;
}
static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)
@@ -150,26 +141,25 @@
static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
{
hwif->set_pio_mode = &cs5520_set_pio_mode;
- hwif->speedproc = &cs5520_tune_chipset;
- hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
- hwif->ide_dma_on = &cs5520_dma_on;
+ hwif->set_dma_mode = &cs5520_set_dma_mode;
- if(!noautodma)
- hwif->autodma = 1;
-
- if(!hwif->dma_base)
- {
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
+ if (hwif->dma_base == 0) {
+ hwif->drives[1].autotune = hwif->drives[0].autotune = 1;
return;
}
+ hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
+ hwif->ide_dma_on = &cs5520_dma_on;
+
/* ATAPI is harder so leave it for now */
hwif->atapi_dma = 0;
hwif->ultra_mask = 0;
hwif->swdma_mask = 0;
hwif->mwdma_mask = 0;
-
+
+ if (!noautodma)
+ hwif->autodma = 1;
+
hwif->drives[0].autodma = hwif->autodma;
hwif->drives[1].autodma = hwif->autodma;
}
diff --git a/drivers/ide/pci/cs5530.c b/drivers/ide/pci/cs5530.c
index 741507b..e412157 100644
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -30,22 +30,6 @@
#include <asm/io.h>
#include <asm/irq.h>
-/**
- * cs5530_xfer_set_mode - set a new transfer mode at the drive
- * @drive: drive to tune
- * @mode: new mode
- *
- * Logging wrapper to the IDE driver speed configuration. This can
- * probably go away now.
- */
-
-static int cs5530_set_xfer_mode (ide_drive_t *drive, u8 mode)
-{
- printk(KERN_DEBUG "%s: cs5530_set_xfer_mode(%s)\n",
- drive->name, ide_xfer_verbose(mode));
- return (ide_config_drive_speed(drive, mode));
-}
-
/*
* Here are the standard PIO mode 0-4 timings for each "format".
* Format-0 uses fast data reg timings, with slower command reg timings.
@@ -62,20 +46,12 @@
#define CS5530_BAD_PIO(timings) (((timings)&~0x80000000)==0x0000e132)
#define CS5530_BASEREG(hwif) (((hwif)->dma_base & ~0xf) + ((hwif)->channel ? 0x30 : 0x20))
-static void cs5530_tunepio(ide_drive_t *drive, u8 pio)
-{
- unsigned long basereg = CS5530_BASEREG(drive->hwif);
- unsigned int format = (inl(basereg + 4) >> 31) & 1;
-
- outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
-}
-
/**
- * cs5530_set_pio_mode - set PIO mode
+ * cs5530_set_pio_mode - set host controller for PIO mode
* @drive: drive
* @pio: PIO mode number
*
- * Handles setting of PIO mode for both the chipset and drive.
+ * Handles setting of PIO mode for the chipset.
*
* The init_hwif_cs5530() routine guarantees that all drives
* will have valid default PIO timings set up before we get here.
@@ -83,8 +59,10 @@
static void cs5530_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- if (cs5530_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
- cs5530_tunepio(drive, pio);
+ unsigned long basereg = CS5530_BASEREG(drive->hwif);
+ unsigned int format = (inl(basereg + 4) >> 31) & 1;
+
+ outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
}
/**
@@ -142,20 +120,11 @@
return 1;
}
-static int cs5530_tune_chipset(ide_drive_t *drive, const u8 mode)
+static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
unsigned long basereg;
unsigned int reg, timings = 0;
- /*
- * Tell the drive to switch to the new mode; abort on failure.
- */
- if (cs5530_set_xfer_mode(drive, mode))
- return 1; /* failure */
-
- /*
- * Now tune the chipset to match the drive:
- */
switch (mode) {
case XFER_UDMA_0: timings = 0x00921250; break;
case XFER_UDMA_1: timings = 0x00911140; break;
@@ -180,8 +149,6 @@
outl(reg, basereg + 4); /* write drive0 config register */
outl(timings, basereg + 12); /* write drive1 config register */
}
-
- return 0; /* success */
}
/**
@@ -299,7 +266,7 @@
hwif->serialized = hwif->mate->serialized = 1;
hwif->set_pio_mode = &cs5530_set_pio_mode;
- hwif->speedproc = &cs5530_tune_chipset;
+ hwif->set_dma_mode = &cs5530_set_dma_mode;
basereg = CS5530_BASEREG(hwif);
d0_timings = inl(basereg + 0);
@@ -340,6 +307,7 @@
.autodma = AUTODMA,
.bootable = ON_BOARD,
.pio_mask = ATA_PIO4,
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
};
static int __devinit cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
diff --git a/drivers/ide/pci/cs5535.c b/drivers/ide/pci/cs5535.c
index 383b7ec..2578657 100644
--- a/drivers/ide/pci/cs5535.c
+++ b/drivers/ide/pci/cs5535.c
@@ -131,24 +131,21 @@
}
}
-/****
- * cs5535_set_drive - Configure the drive to the new speed
- * @drive: Drive to set up
- * @speed: desired speed
+/**
+ * cs5535_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * cs5535_set_drive() configures the drive and the chipset to a
- * new speed. It also can be called by upper layers.
+ * Programs the chipset for DMA mode.
*/
-static int cs5535_set_drive(ide_drive_t *drive, u8 speed)
-{
- ide_config_drive_speed(drive, speed);
- cs5535_set_speed(drive, speed);
- return 0;
+static void cs5535_set_dma_mode(ide_drive_t *drive, const u8 speed)
+{
+ cs5535_set_speed(drive, speed);
}
/**
- * cs5535_set_pio_mode - PIO setup
+ * cs5535_set_pio_mode - set host controller for PIO mode
* @drive: drive
* @pio: PIO mode number
*
@@ -157,7 +154,6 @@
static void cs5535_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- ide_config_drive_speed(drive, XFER_PIO_0 + pio);
cs5535_set_speed(drive, XFER_PIO_0 + pio);
}
@@ -194,12 +190,16 @@
*/
static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
{
- int i;
-
hwif->autodma = 0;
hwif->set_pio_mode = &cs5535_set_pio_mode;
- hwif->speedproc = &cs5535_set_drive;
+ hwif->set_dma_mode = &cs5535_set_dma_mode;
+
+ hwif->drives[1].autotune = hwif->drives[0].autotune = 1;
+
+ if (hwif->dma_base == 0)
+ return;
+
hwif->ide_dma_check = &cs5535_dma_check;
hwif->atapi_dma = 1;
@@ -211,11 +211,7 @@
if (!noautodma)
hwif->autodma = 1;
- /* just setting autotune and not worrying about bios timings */
- for (i = 0; i < 2; i++) {
- hwif->drives[i].autotune = 1;
- hwif->drives[i].autodma = hwif->autodma;
- }
+ hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
}
static ide_pci_device_t cs5535_chipset __devinitdata = {
@@ -223,7 +219,7 @@
.init_hwif = init_hwif_cs5535,
.autodma = AUTODMA,
.bootable = ON_BOARD,
- .host_flags = IDE_HFLAG_SINGLE,
+ .host_flags = IDE_HFLAG_SINGLE | IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO4,
};
diff --git a/drivers/ide/pci/hpt34x.c b/drivers/ide/pci/hpt34x.c
index a1bb101..218852a 100644
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -43,7 +43,7 @@
#define HPT343_DEBUG_DRIVE_INFO 0
-static int hpt34x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt34x_set_mode(ide_drive_t *drive, const u8 speed)
{
struct pci_dev *dev = HWIF(drive)->pci_dev;
u32 reg1= 0, tmp1 = 0, reg2 = 0, tmp2 = 0;
@@ -73,13 +73,11 @@
drive->dn, reg1, tmp1, reg2, tmp2,
hi_speed, lo_speed);
#endif /* HPT343_DEBUG_DRIVE_INFO */
-
- return(ide_config_drive_speed(drive, speed));
}
static void hpt34x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void) hpt34x_tune_chipset(drive, (XFER_PIO_0 + pio));
+ hpt34x_set_mode(drive, XFER_PIO_0 + pio);
}
static int hpt34x_config_drive_xfer_rate (ide_drive_t *drive)
@@ -145,7 +143,8 @@
hwif->autodma = 0;
hwif->set_pio_mode = &hpt34x_set_pio_mode;
- hwif->speedproc = &hpt34x_tune_chipset;
+ hwif->set_dma_mode = &hpt34x_set_mode;
+
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index 0e7d3b6..8812a9b 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -600,7 +600,7 @@
return (*info->settings)[i];
}
-static int hpt36x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt36x_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -623,11 +623,9 @@
new_itr &= ~0xc0000000;
pci_write_config_dword(dev, itr_addr, new_itr);
-
- return ide_config_drive_speed(drive, speed);
}
-static int hpt37x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt37x_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -647,24 +645,22 @@
if (speed < XFER_MW_DMA_0)
new_itr &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
pci_write_config_dword(dev, itr_addr, new_itr);
-
- return ide_config_drive_speed(drive, speed);
}
-static int hpt3xx_tune_chipset(ide_drive_t *drive, u8 speed)
+static void hpt3xx_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct hpt_info *info = pci_get_drvdata(hwif->pci_dev);
if (info->chip_type >= HPT370)
- return hpt37x_tune_chipset(drive, speed);
+ hpt37x_set_mode(drive, speed);
else /* hpt368: hpt_minimum_revision(dev, 2) */
- return hpt36x_tune_chipset(drive, speed);
+ hpt36x_set_mode(drive, speed);
}
static void hpt3xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
+ hpt3xx_set_mode(drive, XFER_PIO_0 + pio);
}
static int hpt3xx_quirkproc(ide_drive_t *drive)
@@ -1257,7 +1253,7 @@
hwif->select_data = hwif->channel ? 0x54 : 0x50;
hwif->set_pio_mode = &hpt3xx_set_pio_mode;
- hwif->speedproc = &hpt3xx_tune_chipset;
+ hwif->set_dma_mode = &hpt3xx_set_mode;
hwif->quirkproc = &hpt3xx_quirkproc;
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c
index 76e91ff..ecf4ce0 100644
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -48,15 +48,15 @@
}
}
-/*
- * it8213_tune_pio - tune a drive
- * @drive: drive to tune
- * @pio: desired PIO mode
+/**
+ * it8213_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Set the interface PIO mode.
*/
-static void it8213_tune_pio(ide_drive_t *drive, const u8 pio)
+static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -105,21 +105,15 @@
spin_unlock_irqrestore(&tune_lock, flags);
}
-static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- it8213_tune_pio(drive, pio);
- ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
/**
- * it8213_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @speed: speed we want to achieve
+ * it8213_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Tune the ITE chipset for the desired mode.
+ * Tune the ITE chipset for the DMA mode.
*/
-static int it8213_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void it8213_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -152,7 +146,7 @@
case XFER_SW_DMA_2:
break;
default:
- return -1;
+ return;
}
if (speed >= XFER_UDMA_0) {
@@ -182,9 +176,7 @@
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
- it8213_tune_pio(drive, it8213_dma_2_pio(speed));
-
- return ide_config_drive_speed(drive, speed);
+ it8213_set_pio_mode(drive, it8213_dma_2_pio(speed));
}
/**
@@ -220,7 +212,7 @@
{
u8 reg42h = 0;
- hwif->speedproc = &it8213_tune_chipset;
+ hwif->set_dma_mode = &it8213_set_dma_mode;
hwif->set_pio_mode = &it8213_set_pio_mode;
hwif->autodma = 0;
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
index 758a982..1b69d82 100644
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -229,24 +229,24 @@
}
/**
- * it821x_tunepio - tune a drive
- * @drive: drive to tune
- * @pio: the desired PIO mode
+ * it821x_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
- * Try to tune the drive/host to the desired PIO mode taking into
- * the consideration the maximum PIO mode supported by the other
- * device on the cable.
+ * Tune the host to the desired PIO mode taking into the consideration
+ * the maximum PIO mode supported by the other device on the cable.
*/
-static int it821x_tunepio(ide_drive_t *drive, u8 set_pio)
+static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = drive->hwif;
struct it821x_dev *itdev = ide_get_hwifdata(hwif);
int unit = drive->select.b.unit;
ide_drive_t *pair = &hwif->drives[1 - unit];
+ u8 set_pio = pio;
/* Spec says 89 ref driver uses 88 */
- static u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+ static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
/*
@@ -261,22 +261,12 @@
set_pio = pair_pio;
}
- if (itdev->smart)
- return 0;
-
/* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
itdev->want[unit][1] = pio_want[set_pio];
itdev->want[unit][0] = 1; /* PIO is lowest priority */
- itdev->pio[unit] = pio[set_pio];
+ itdev->pio[unit] = pio_timings[set_pio];
it821x_clock_strategy(drive);
it821x_program(drive, itdev->pio[unit]);
-
- return ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
-}
-
-static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- (void)it821x_tunepio(drive, pio);
}
/**
@@ -405,47 +395,24 @@
}
/**
- * it821x_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @speed: speed we want to achieve
+ * it821x_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Tune the ITE chipset for the desired mode.
+ * Tune the ITE chipset for the desired DMA mode.
*/
-static int it821x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
-
- ide_hwif_t *hwif = drive->hwif;
- struct it821x_dev *itdev = ide_get_hwifdata(hwif);
-
- if (itdev->smart == 0) {
- switch (speed) {
- /* MWDMA tuning is really hard because our MWDMA and PIO
- timings are kept in the same place. We can switch in the
- host dma on/off callbacks */
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
- break;
- case XFER_UDMA_6:
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- it821x_tune_udma(drive, (speed - XFER_UDMA_0));
- break;
- default:
- return 1;
- }
-
- return ide_config_drive_speed(drive, speed);
- }
-
- /* don't touch anything in the smart mode */
- return 0;
+ /*
+ * MWDMA tuning is really hard because our MWDMA and PIO
+ * timings are kept in the same place. We can switch in the
+ * host dma on/off callbacks.
+ */
+ if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
+ it821x_tune_udma(drive, speed - XFER_UDMA_0);
+ else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
}
/**
@@ -629,14 +596,15 @@
printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
}
- hwif->speedproc = &it821x_tune_chipset;
- hwif->set_pio_mode = &it821x_set_pio_mode;
+ if (idev->smart == 0) {
+ hwif->set_pio_mode = &it821x_set_pio_mode;
+ hwif->set_dma_mode = &it821x_set_dma_mode;
- /* MWDMA/PIO clock switching for pass through mode */
- if(!idev->smart) {
+ /* MWDMA/PIO clock switching for pass through mode */
hwif->dma_start = &it821x_dma_start;
hwif->ide_dma_end = &it821x_dma_end;
- }
+ } else
+ hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/jmicron.c b/drivers/ide/pci/jmicron.c
index d379fba..582b4ca 100644
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -85,21 +85,18 @@
static void jmicron_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
/**
- * jmicron_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @speed: speed we want to achieve
+ * jmicron_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @mode: DMA mode
*
- * As the JMicron snoops for timings all we actually need to do is
- * set the transfer mode on the device.
+ * As the JMicron snoops for timings we don't need to do anything here.
*/
-static int jmicron_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void jmicron_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
- return ide_config_drive_speed(drive, speed);
}
/**
@@ -129,8 +126,8 @@
static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
{
- hwif->speedproc = &jmicron_tune_chipset;
hwif->set_pio_mode = &jmicron_set_pio_mode;
+ hwif->set_dma_mode = &jmicron_set_dma_mode;
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index 5fb1eed..ad0bdcb 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -146,19 +146,16 @@
{ 0x1a, 0x01, 0xcb }, /* UDMA mode 6 */
};
-static int pdcnew_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pdcnew_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
u8 adj = (drive->dn & 1) ? 0x08 : 0x00;
- int err;
/*
- * Issue SETFEATURES_XFER to the drive first. PDC202xx hardware will
+ * IDE core issues SETFEATURES_XFER to the drive first (thanks to
+ * IDE_HFLAG_POST_SET_MODE in ->host_flags). PDC202xx hardware will
* automatically set the timing registers based on 100 MHz PLL output.
- */
- err = ide_config_drive_speed(drive, speed);
-
- /*
+ *
* As we set up the PLL to output 133 MHz for UltraDMA/133 capable
* chips, we must override the default register settings...
*/
@@ -211,13 +208,11 @@
set_indexed_reg(hwif, 0x10 + adj, tmp & 0x7f);
}
-
- return err;
}
static void pdcnew_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void)pdcnew_tune_chipset(drive, XFER_PIO_0 + pio);
+ pdcnew_set_mode(drive, XFER_PIO_0 + pio);
}
static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
@@ -490,9 +485,9 @@
hwif->autodma = 0;
hwif->set_pio_mode = &pdcnew_set_pio_mode;
+ hwif->set_dma_mode = &pdcnew_set_mode;
hwif->quirkproc = &pdcnew_quirkproc;
- hwif->speedproc = &pdcnew_tune_chipset;
hwif->resetproc = &pdcnew_reset;
hwif->err_stops_fifo = 1;
@@ -583,6 +578,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x3f, /* udma0-5 */
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 1 */
.name = "PDC20269",
.init_setup = init_setup_pdcnew,
@@ -592,6 +588,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x7f, /* udma0-6*/
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 2 */
.name = "PDC20270",
.init_setup = init_setup_pdc20270,
@@ -601,6 +598,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x3f, /* udma0-5 */
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 3 */
.name = "PDC20271",
.init_setup = init_setup_pdcnew,
@@ -610,6 +608,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x7f, /* udma0-6*/
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 4 */
.name = "PDC20275",
.init_setup = init_setup_pdcnew,
@@ -619,6 +618,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x7f, /* udma0-6*/
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 5 */
.name = "PDC20276",
.init_setup = init_setup_pdc20276,
@@ -628,6 +628,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x7f, /* udma0-6*/
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
},{ /* 6 */
.name = "PDC20277",
.init_setup = init_setup_pdcnew,
@@ -637,6 +638,7 @@
.bootable = OFF_BOARD,
.pio_mask = ATA_PIO4,
.udma_mask = 0x7f, /* udma0-6*/
+ .host_flags = IDE_HFLAG_POST_SET_MODE,
}
};
diff --git a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c
index b578307..8c3e8cf 100644
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -63,7 +63,7 @@
static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
-static int pdc202xx_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -138,13 +138,11 @@
pci_read_config_dword(dev, drive_pci, &drive_conf);
printk("0x%08x\n", drive_conf);
#endif
-
- return ide_config_drive_speed(drive, speed);
}
static void pdc202xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- pdc202xx_tune_chipset(drive, XFER_PIO_0 + pio);
+ pdc202xx_set_mode(drive, XFER_PIO_0 + pio);
}
static u8 pdc202xx_old_cable_detect (ide_hwif_t *hwif)
@@ -330,14 +328,13 @@
hwif->autodma = 0;
hwif->set_pio_mode = &pdc202xx_set_pio_mode;
+ hwif->set_dma_mode = &pdc202xx_set_mode;
hwif->quirkproc = &pdc202xx_quirkproc;
if (hwif->pci_dev->device != PCI_DEVICE_ID_PROMISE_20246)
hwif->resetproc = &pdc202xx_reset;
- hwif->speedproc = &pdc202xx_tune_chipset;
-
hwif->err_stops_fifo = 1;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c
index fd8214a..38c91ba6 100644
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -137,13 +137,14 @@
}
/**
- * piix_tune_pio - tune PIIX for PIO mode
- * @drive: drive to tune
- * @pio: desired PIO mode
+ * piix_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Set the interface PIO mode based upon the settings done by AMI BIOS.
*/
-static void piix_tune_pio (ide_drive_t *drive, u8 pio)
+
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -204,31 +205,15 @@
}
/**
- * piix_set_pio_mode - set PIO mode
- * @drive: drive to tune
- * @pio: desired PIO mode
+ * piix_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Set the drive's PIO mode (might be useful if drive is not registered
- * in CMOS for any reason).
+ * Set a PIIX host controller to the desired DMA mode. This involves
+ * programming the right timing data into the PCI configuration space.
*/
-static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- piix_tune_pio(drive, pio);
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-/**
- * piix_tune_chipset - tune a PIIX interface
- * @drive: IDE drive to tune
- * @speed: speed to configure
- *
- * Set a PIIX interface channel to the desired speeds. This involves
- * requires the right timing data into the PIIX configuration space
- * then setting the drive parameters appropriately
- */
-
-static int piix_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -259,7 +244,7 @@
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_SW_DMA_2: break;
- default: return -1;
+ default: return;
}
if (speed >= XFER_UDMA_0) {
@@ -288,9 +273,7 @@
pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
}
- piix_tune_pio(drive, piix_dma_2_pio(speed));
-
- return ide_config_drive_speed(drive, speed);
+ piix_set_pio_mode(drive, piix_dma_2_pio(speed));
}
/**
@@ -448,7 +431,8 @@
hwif->autodma = 0;
hwif->set_pio_mode = &piix_set_pio_mode;
- hwif->speedproc = &piix_tune_chipset;
+ hwif->set_dma_mode = &piix_set_dma_mode;
+
hwif->drives[0].autotune = 1;
hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index 79ecab6..ee0e3f5 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -68,17 +68,6 @@
return pci_clock;
}
-extern char *ide_xfer_verbose (byte xfer_rate);
-
-/*
- * Set a new transfer mode at the drive
- */
-static int sc1200_set_xfer_mode (ide_drive_t *drive, byte mode)
-{
- printk("%s: sc1200_set_xfer_mode(%s)\n", drive->name, ide_xfer_verbose(mode));
- return ide_config_drive_speed(drive, mode);
-}
-
/*
* Here are the standard PIO mode 0-4 timings for each "format".
* Format-0 uses fast data reg timings, with slower command reg timings.
@@ -138,7 +127,7 @@
return mask;
}
-static int sc1200_tune_chipset(ide_drive_t *drive, const u8 mode)
+static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode)
{
ide_hwif_t *hwif = HWIF(drive);
int unit = drive->select.b.unit;
@@ -146,17 +135,9 @@
unsigned short pci_clock;
unsigned int basereg = hwif->channel ? 0x50 : 0x40;
- /*
- * Tell the drive to switch to the new mode; abort on failure.
- */
- if (sc1200_set_xfer_mode(drive, mode))
- return 1; /* failure */
-
pci_clock = sc1200_get_pci_clock();
/*
- * Now tune the chipset to match the drive:
- *
* Note that each DMA mode has several timings associated with it.
* The correct timing depends on the fast PCI clock freq.
*/
@@ -216,8 +197,6 @@
} else {
pci_write_config_dword(hwif->pci_dev, basereg+12, timings);
}
-
- return 0; /* success */
}
/*
@@ -286,13 +265,12 @@
if (mode != -1) {
printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
hwif->dma_off_quietly(drive);
- if (sc1200_tune_chipset(drive, mode) == 0)
+ if (ide_set_dma_mode(drive, mode) == 0)
hwif->dma_host_on(drive);
return;
}
- if (sc1200_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
- sc1200_tunepio(drive, pio);
+ sc1200_tunepio(drive, pio);
}
#ifdef CONFIG_PM
@@ -400,16 +378,20 @@
if (hwif->mate)
hwif->serialized = hwif->mate->serialized = 1;
hwif->autodma = 0;
- if (hwif->dma_base) {
- hwif->udma_filter = sc1200_udma_filter;
- hwif->ide_dma_check = &sc1200_config_dma;
- hwif->ide_dma_end = &sc1200_ide_dma_end;
- if (!noautodma)
- hwif->autodma = 1;
- hwif->set_pio_mode = &sc1200_set_pio_mode;
- hwif->speedproc = &sc1200_tune_chipset;
- }
+ hwif->set_pio_mode = &sc1200_set_pio_mode;
+ hwif->set_dma_mode = &sc1200_set_dma_mode;
+
+ if (hwif->dma_base == 0)
+ return;
+
+ hwif->udma_filter = sc1200_udma_filter;
+ hwif->ide_dma_check = &sc1200_config_dma;
+ hwif->ide_dma_end = &sc1200_ide_dma_end;
+
+ if (!noautodma)
+ hwif->autodma = 1;
+
hwif->atapi_dma = 1;
hwif->ultra_mask = 0x07;
hwif->mwdma_mask = 0x07;
@@ -423,7 +405,7 @@
.init_hwif = init_hwif_sc1200,
.autodma = AUTODMA,
.bootable = ON_BOARD,
- .host_flags = IDE_HFLAG_ABUSE_DMA_MODES,
+ .host_flags = IDE_HFLAG_ABUSE_DMA_MODES | IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO4,
};
diff --git a/drivers/ide/pci/scc_pata.c b/drivers/ide/pci/scc_pata.c
index 66a526e..67f06dd 100644
--- a/drivers/ide/pci/scc_pata.c
+++ b/drivers/ide/pci/scc_pata.c
@@ -190,15 +190,15 @@
}
/**
- * scc_tune_pio - tune a drive PIO mode
- * @drive: drive to tune
- * @mode_wanted: the target operating mode
+ * scc_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Load the timing settings for this device mode into the
* controller.
*/
-static void scc_tune_pio(ide_drive_t *drive, const u8 pio)
+static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct scc_ports *ports = ide_get_hwifdata(hwif);
@@ -221,22 +221,16 @@
out_be32((void __iomem *)pioct_port, reg);
}
-static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- scc_tune_pio(drive, pio);
- ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
/**
- * scc_tune_chipset - tune a drive DMA mode
- * @drive: Drive to set up
- * @speed: speed we want to achieve
+ * scc_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
* Load the timing settings for this device mode into the
* controller.
*/
-static int scc_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void scc_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct scc_ports *ports = ide_get_hwifdata(hwif);
@@ -271,7 +265,7 @@
idx = speed - XFER_UDMA_0;
break;
default:
- return 1;
+ return;
}
jcactsel = JCACTSELtbl[offset][idx];
@@ -287,8 +281,6 @@
}
reg = JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx];
out_be32((void __iomem *)udenvt_port, reg);
-
- return ide_config_drive_speed(drive, speed);
}
/**
@@ -708,8 +700,8 @@
hwif->dma_setup = scc_dma_setup;
hwif->ide_dma_end = scc_ide_dma_end;
- hwif->speedproc = scc_tune_chipset;
hwif->set_pio_mode = scc_set_pio_mode;
+ hwif->set_dma_mode = scc_set_dma_mode;
hwif->ide_dma_check = scc_config_drive_for_dma;
hwif->ide_dma_test_irq = scc_dma_test_irq;
hwif->udma_filter = scc_udma_filter;
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index 0351cf2..49ec0ac 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -124,7 +124,7 @@
return 0;
}
-static void svwks_tune_pio(ide_drive_t *drive, const u8 pio)
+static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
@@ -145,7 +145,7 @@
}
}
-static int svwks_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
@@ -193,14 +193,6 @@
pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
pci_write_config_byte(dev, 0x54, ultra_enable);
-
- return (ide_config_drive_speed(drive, speed));
-}
-
-static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- svwks_tune_pio(drive, pio);
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
}
static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
@@ -384,7 +376,7 @@
hwif->irq = hwif->channel ? 15 : 14;
hwif->set_pio_mode = &svwks_set_pio_mode;
- hwif->speedproc = &svwks_tune_chipset;
+ hwif->set_dma_mode = &svwks_set_dma_mode;
hwif->udma_filter = &svwks_udma_filter;
hwif->atapi_dma = 1;
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index c292e1d..85ffaaa 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -291,12 +291,8 @@
drive->hwif->dma_host_off(drive);
}
-static int sgiioc4_speedproc(ide_drive_t *drive, const u8 speed)
+static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
- if (speed != XFER_MW_DMA_2)
- return 1;
-
- return ide_config_drive_speed(drive, speed);
}
static int sgiioc4_ide_dma_check(ide_drive_t *drive)
@@ -591,11 +587,9 @@
ide_init_sgiioc4(ide_hwif_t * hwif)
{
hwif->mmio = 1;
- hwif->atapi_dma = 1;
- hwif->mwdma_mask = 0x04;
hwif->pio_mask = 0x00;
hwif->set_pio_mode = NULL; /* Sets timing for PIO mode */
- hwif->speedproc = &sgiioc4_speedproc;
+ hwif->set_dma_mode = &sgiioc4_set_dma_mode;
hwif->selectproc = NULL;/* Use the default routine to select drive */
hwif->reset_poll = NULL;/* No HBA specific reset_poll needed */
hwif->pre_reset = NULL; /* No HBA specific pre_set needed */
@@ -606,6 +600,14 @@
hwif->quirkproc = NULL;
hwif->busproc = NULL;
+ hwif->INB = &sgiioc4_INB;
+
+ if (hwif->dma_base == 0)
+ return;
+
+ hwif->atapi_dma = 1;
+ hwif->mwdma_mask = 0x04;
+
hwif->dma_setup = &sgiioc4_ide_dma_setup;
hwif->dma_start = &sgiioc4_ide_dma_start;
hwif->ide_dma_end = &sgiioc4_ide_dma_end;
@@ -617,8 +619,6 @@
hwif->dma_host_off = &sgiioc4_dma_host_off;
hwif->dma_lost_irq = &sgiioc4_dma_lost_irq;
hwif->dma_timeout = &ide_dma_timeout;
-
- hwif->INB = &sgiioc4_INB;
}
static int __devinit
@@ -688,8 +688,6 @@
/* Initializing chipset IRQ Registers */
writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));
- ide_init_sgiioc4(hwif);
-
hwif->autodma = 0;
if (dma_base && ide_dma_sgiioc4(hwif, dma_base) == 0) {
@@ -699,6 +697,8 @@
printk(KERN_INFO "%s: %s Bus-Master DMA disabled\n",
hwif->name, DRV_NAME);
+ ide_init_sgiioc4(hwif);
+
if (probe_hwif_init(hwif))
return -EIO;
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index 5d1e5e5..ce77849 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -165,16 +165,16 @@
}
/**
- * sil_tune_pio - tune a drive
- * @drive: drive to tune
- * @pio: the desired PIO mode
+ * sil_set_pio_mode - set host controller for PIO mode
+ * @drive: drive
+ * @pio: PIO mode number
*
* Load the timing settings for this device mode into the
* controller. If we are in PIO mode 3 or 4 turn on IORDY
* monitoring (bit 9). The TF timing is bits 31:16
*/
-static void sil_tune_pio(ide_drive_t *drive, u8 pio)
+static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
{
const u16 tf_speed[] = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
@@ -234,21 +234,15 @@
}
}
-static void sil_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- sil_tune_pio(drive, pio);
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
/**
- * siimage_tune_chipset - set controller timings
- * @drive: Drive to set up
- * @speed: speed we want to achieve
+ * sil_set_dma_mode - set host controller for DMA mode
+ * @drive: drive
+ * @speed: DMA mode
*
- * Tune the SII chipset for the desired mode.
+ * Tune the SiI chipset for the desired DMA mode.
*/
-static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
@@ -303,7 +297,7 @@
mode |= ((unit) ? 0x30 : 0x03);
break;
default:
- return 1;
+ return;
}
if (hwif->mmio) {
@@ -315,7 +309,6 @@
pci_write_config_word(hwif->pci_dev, ma, multi);
pci_write_config_word(hwif->pci_dev, ua, ultra);
}
- return (ide_config_drive_speed(drive, speed));
}
/**
@@ -904,8 +897,8 @@
hwif->autodma = 0;
hwif->resetproc = &siimage_reset;
- hwif->speedproc = &siimage_tune_chipset;
hwif->set_pio_mode = &sil_set_pio_mode;
+ hwif->set_dma_mode = &sil_set_dma_mode;
hwif->reset_poll = &siimage_reset_poll;
hwif->pre_reset = &siimage_pre_reset;
hwif->udma_filter = &sil_udma_filter;
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 3e18899..b375ee5 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -451,7 +451,7 @@
}
/* Set per-drive active and recovery time */
-static void config_art_rwp_pio (ide_drive_t *drive, u8 pio)
+static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -519,20 +519,14 @@
}
}
-static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- config_art_rwp_pio(drive, pio);
- (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sis_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
u32 regdw;
u8 drive_pci, reg;
- /* See config_art_rwp_pio for drive pci config registers */
+ /* See sis_set_pio_mode() for drive PCI config registers */
drive_pci = 0x40;
if (chipset_family >= ATA_133) {
u32 reg54h;
@@ -600,8 +594,6 @@
BUG();
break;
}
-
- return ide_config_drive_speed(drive, speed);
}
static int sis5513_config_xfer_rate(ide_drive_t *drive)
@@ -841,7 +833,7 @@
hwif->irq = hwif->channel ? 15 : 14;
hwif->set_pio_mode = &sis_set_pio_mode;
- hwif->speedproc = &sis5513_tune_chipset;
+ hwif->set_dma_mode = &sis_set_dma_mode;
if (chipset_family >= ATA_133)
hwif->udma_filter = sis5513_ata133_udma_filter;
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
index f492318..2ef26e3 100644
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -75,7 +75,7 @@
/*
* Configure the chipset for PIO mode.
*/
-static void sl82c105_tune_pio(ide_drive_t *drive, const u8 pio)
+static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
struct pci_dev *dev = HWIF(drive)->pci_dev;
int reg = 0x44 + drive->dn * 4;
@@ -105,9 +105,9 @@
}
/*
- * Configure the drive and chipset for a new transfer speed.
+ * Configure the chipset for DMA mode.
*/
-static int sl82c105_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
u16 drv_ctrl;
@@ -140,10 +140,8 @@
}
break;
default:
- return -1;
+ return;
}
-
- return ide_config_drive_speed(drive, speed);
}
/*
@@ -306,17 +304,6 @@
pci_read_config_dword(dev, 0x40, &val);
pci_set_drvdata(dev, (void *)val);
}
-
-/*
- * We only deal with PIO mode here - DMA mode 'using_dma' is not
- * initialised at the point that this function is called.
- */
-static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- sl82c105_tune_pio(drive, pio);
-
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
/*
* Return the revision of the Winbond bridge
@@ -383,7 +370,7 @@
DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
hwif->set_pio_mode = &sl82c105_set_pio_mode;
- hwif->speedproc = &sl82c105_tune_chipset;
+ hwif->set_dma_mode = &sl82c105_set_dma_mode;
hwif->selectproc = &sl82c105_selectproc;
hwif->resetproc = &sl82c105_resetproc;
diff --git a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c
index ae8e913..ebac87f 100644
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -42,7 +42,7 @@
}
}
-static void slc90e66_tune_pio (ide_drive_t *drive, u8 pio)
+static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -95,13 +95,7 @@
spin_unlock_irqrestore(&ide_lock, flags);
}
-static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
- slc90e66_tune_pio(drive, pio);
- (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-static int slc90e66_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void slc90e66_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -125,7 +119,7 @@
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_SW_DMA_2: break;
- default: return -1;
+ default: return;
}
if (speed >= XFER_UDMA_0) {
@@ -144,9 +138,7 @@
pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
}
- slc90e66_tune_pio(drive, slc90e66_dma_2_pio(speed));
-
- return ide_config_drive_speed(drive, speed);
+ slc90e66_set_pio_mode(drive, slc90e66_dma_2_pio(speed));
}
static int slc90e66_config_drive_xfer_rate (ide_drive_t *drive)
@@ -172,8 +164,8 @@
if (!hwif->irq)
hwif->irq = hwif->channel ? 15 : 14;
- hwif->speedproc = &slc90e66_tune_chipset;
hwif->set_pio_mode = &slc90e66_set_pio_mode;
+ hwif->set_dma_mode = &slc90e66_set_dma_mode;
pci_read_config_byte(hwif->pci_dev, 0x47, ®47);
diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index e23b9cf..840415d 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -13,7 +13,7 @@
#include <linux/pci.h>
#include <linux/ide.h>
-static int tc86c001_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long scr_port = hwif->config_data + (drive->dn ? 0x02 : 0x00);
@@ -39,13 +39,11 @@
scr &= (speed < XFER_MW_DMA_0) ? 0xf8ff : 0xff0f;
scr |= mode;
outw(scr, scr_port);
-
- return ide_config_drive_speed(drive, speed);
}
static void tc86c001_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void) tc86c001_tune_chipset(drive, XFER_PIO_0 + pio);
+ tc86c001_set_mode(drive, XFER_PIO_0 + pio);
}
/*
@@ -193,7 +191,8 @@
hwif->config_data = sc_base;
hwif->set_pio_mode = &tc86c001_set_pio_mode;
- hwif->speedproc = &tc86c001_tune_chipset;
+ hwif->set_dma_mode = &tc86c001_set_mode;
+
hwif->busproc = &tc86c001_busproc;
hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/triflex.c b/drivers/ide/pci/triflex.c
index c3ff066..54e411d 100644
--- a/drivers/ide/pci/triflex.c
+++ b/drivers/ide/pci/triflex.c
@@ -40,7 +40,7 @@
#include <linux/ide.h>
#include <linux/init.h>
-static int triflex_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void triflex_set_mode(ide_drive_t *drive, const u8 speed)
{
ide_hwif_t *hwif = HWIF(drive);
struct pci_dev *dev = hwif->pci_dev;
@@ -82,20 +82,18 @@
timing = 0x0808;
break;
default:
- return -1;
+ return;
}
triflex_timings &= ~(0xFFFF << (16 * unit));
triflex_timings |= (timing << (16 * unit));
pci_write_config_dword(dev, channel_offset, triflex_timings);
-
- return (ide_config_drive_speed(drive, speed));
}
static void triflex_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- (void)triflex_tune_chipset(drive, XFER_PIO_0 + pio);
+ triflex_set_mode(drive, XFER_PIO_0 + pio);
}
static int triflex_config_drive_xfer_rate(ide_drive_t *drive)
@@ -111,7 +109,7 @@
static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
{
hwif->set_pio_mode = &triflex_set_pio_mode;
- hwif->speedproc = &triflex_tune_chipset;
+ hwif->set_dma_mode = &triflex_set_mode;
if (hwif->dma_base == 0)
return;
diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
index 378feb4..479e496 100644
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -1,6 +1,6 @@
/*
*
- * Version 3.48
+ * Version 3.49
*
* VIA IDE driver for Linux. Supported southbridges:
*
@@ -153,21 +153,17 @@
* @drive: Drive to set up
* @speed: desired speed
*
- * via_set_drive() computes timing values configures the drive and
- * the chipset to a desired transfer mode. It also can be called
- * by upper layers.
+ * via_set_drive() computes timing values configures the chipset to
+ * a desired transfer mode. It also can be called by upper layers.
*/
-static int via_set_drive(ide_drive_t *drive, const u8 speed)
+static void via_set_drive(ide_drive_t *drive, const u8 speed)
{
ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
struct via82cxxx_dev *vdev = pci_get_drvdata(drive->hwif->pci_dev);
struct ide_timing t, p;
unsigned int T, UT;
- if (speed != XFER_PIO_SLOW)
- ide_config_drive_speed(drive, speed);
-
T = 1000000000 / via_clock;
switch (vdev->via_config->udma_mask) {
@@ -186,16 +182,10 @@
}
via_set_speed(HWIF(drive), drive->dn, &t);
-
- if (!drive->init_speed)
- drive->init_speed = speed;
- drive->current_speed = speed;
-
- return 0;
}
/**
- * via_set_pio_mode - PIO setup
+ * via_set_pio_mode - set host controller for PIO mode
* @drive: drive
* @pio: PIO mode number
*
@@ -456,8 +446,7 @@
hwif->autodma = 0;
hwif->set_pio_mode = &via_set_pio_mode;
- hwif->speedproc = &via_set_drive;
-
+ hwif->set_dma_mode = &via_set_drive;
#ifdef CONFIG_PPC_CHRP
if(machine_is(chrp) && _chrp_type == _CHRP_Pegasos) {
@@ -500,7 +489,8 @@
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}},
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_PIO_NO_BLACKLIST
- | IDE_HFLAG_PIO_NO_DOWNGRADE,
+ | IDE_HFLAG_PIO_NO_DOWNGRADE
+ | IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO5,
},{ /* 1 */
.name = "VP_IDE",
@@ -510,7 +500,8 @@
.enablebits = {{0x00,0x00,0x00}, {0x00,0x00,0x00}},
.bootable = ON_BOARD,
.host_flags = IDE_HFLAG_PIO_NO_BLACKLIST
- | IDE_HFLAG_PIO_NO_DOWNGRADE,
+ | IDE_HFLAG_PIO_NO_DOWNGRADE
+ | IDE_HFLAG_POST_SET_MODE,
.pio_mask = ATA_PIO5,
}
};
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index f759a53..7d88738 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -392,6 +392,7 @@
for (i=0; table[i].cycle_time; i++)
if (cycle_time > table[i+1].cycle_time)
return table[i].timing_reg;
+ BUG();
return 0;
}
@@ -529,97 +530,12 @@
}
/*
- * Send the SET_FEATURE IDE command to the drive and update drive->id with
- * the new state. We currently don't use the generic routine as it used to
- * cause various trouble, especially with older mediabays.
- * This code is sometimes triggering a spurrious interrupt though, I need
- * to sort that out sooner or later and see if I can finally get the
- * common version to work properly in all cases
- */
-static int
-pmac_ide_do_setfeature(ide_drive_t *drive, u8 command)
-{
- ide_hwif_t *hwif = HWIF(drive);
- int result = 1;
-
- disable_irq_nosync(hwif->irq);
- udelay(1);
- SELECT_DRIVE(drive);
- SELECT_MASK(drive, 0);
- udelay(1);
- /* Get rid of pending error state */
- (void) hwif->INB(IDE_STATUS_REG);
- /* Timeout bumped for some powerbooks */
- if (wait_for_ready(drive, 2000)) {
- /* Timeout bumped for some powerbooks */
- printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
- "before SET_FEATURE!\n", drive->name);
- goto out;
- }
- udelay(10);
- hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
- hwif->OUTB(command, IDE_NSECTOR_REG);
- hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
- hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
- udelay(1);
- /* Timeout bumped for some powerbooks */
- result = wait_for_ready(drive, 2000);
- hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
- if (result)
- printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
- "after SET_FEATURE !\n", drive->name);
-out:
- SELECT_MASK(drive, 0);
- if (result == 0) {
- drive->id->dma_ultra &= ~0xFF00;
- drive->id->dma_mword &= ~0x0F00;
- drive->id->dma_1word &= ~0x0F00;
- switch(command) {
- case XFER_UDMA_7:
- drive->id->dma_ultra |= 0x8080; break;
- case XFER_UDMA_6:
- drive->id->dma_ultra |= 0x4040; break;
- case XFER_UDMA_5:
- drive->id->dma_ultra |= 0x2020; break;
- case XFER_UDMA_4:
- drive->id->dma_ultra |= 0x1010; break;
- case XFER_UDMA_3:
- drive->id->dma_ultra |= 0x0808; break;
- case XFER_UDMA_2:
- drive->id->dma_ultra |= 0x0404; break;
- case XFER_UDMA_1:
- drive->id->dma_ultra |= 0x0202; break;
- case XFER_UDMA_0:
- drive->id->dma_ultra |= 0x0101; break;
- case XFER_MW_DMA_2:
- drive->id->dma_mword |= 0x0404; break;
- case XFER_MW_DMA_1:
- drive->id->dma_mword |= 0x0202; break;
- case XFER_MW_DMA_0:
- drive->id->dma_mword |= 0x0101; break;
- case XFER_SW_DMA_2:
- drive->id->dma_1word |= 0x0404; break;
- case XFER_SW_DMA_1:
- drive->id->dma_1word |= 0x0202; break;
- case XFER_SW_DMA_0:
- drive->id->dma_1word |= 0x0101; break;
- default: break;
- }
- if (!drive->init_speed)
- drive->init_speed = command;
- drive->current_speed = command;
- }
- enable_irq(hwif->irq);
- return result;
-}
-
-/*
* Old tuning functions (called on hdparm -p), sets up drive PIO timings
*/
static void
pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
- u32 *timings;
+ u32 *timings, t;
unsigned accessTicks, recTicks;
unsigned accessTime, recTime;
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
@@ -630,6 +546,7 @@
/* which drive is it ? */
timings = &pmif->timings[drive->select.b.unit & 0x01];
+ t = *timings;
cycle_time = ide_pio_cycle_time(drive, pio);
@@ -637,18 +554,14 @@
case controller_sh_ata6: {
/* 133Mhz cell */
u32 tr = kauai_lookup_timing(shasta_pio_timings, cycle_time);
- if (tr == 0)
- return;
- *timings = ((*timings) & ~TR_133_PIOREG_PIO_MASK) | tr;
+ t = (t & ~TR_133_PIOREG_PIO_MASK) | tr;
break;
}
case controller_un_ata6:
case controller_k2_ata6: {
/* 100Mhz cell */
u32 tr = kauai_lookup_timing(kauai_pio_timings, cycle_time);
- if (tr == 0)
- return;
- *timings = ((*timings) & ~TR_100_PIOREG_PIO_MASK) | tr;
+ t = (t & ~TR_100_PIOREG_PIO_MASK) | tr;
break;
}
case controller_kl_ata4:
@@ -662,9 +575,9 @@
accessTicks = min(accessTicks, 0x1fU);
recTicks = SYSCLK_TICKS_66(recTime);
recTicks = min(recTicks, 0x1fU);
- *timings = ((*timings) & ~TR_66_PIO_MASK) |
- (accessTicks << TR_66_PIO_ACCESS_SHIFT) |
- (recTicks << TR_66_PIO_RECOVERY_SHIFT);
+ t = (t & ~TR_66_PIO_MASK) |
+ (accessTicks << TR_66_PIO_ACCESS_SHIFT) |
+ (recTicks << TR_66_PIO_RECOVERY_SHIFT);
break;
default: {
/* 33Mhz cell */
@@ -684,11 +597,11 @@
recTicks--; /* guess, but it's only for PIO0, so... */
ebit = 1;
}
- *timings = ((*timings) & ~TR_33_PIO_MASK) |
+ t = (t & ~TR_33_PIO_MASK) |
(accessTicks << TR_33_PIO_ACCESS_SHIFT) |
(recTicks << TR_33_PIO_RECOVERY_SHIFT);
if (ebit)
- *timings |= TR_33_PIO_E;
+ t |= TR_33_PIO_E;
break;
}
}
@@ -698,9 +611,7 @@
drive->name, pio, *timings);
#endif
- if (pmac_ide_do_setfeature(drive, XFER_PIO_0 + pio))
- return;
-
+ *timings = t;
pmac_ide_do_update_timings(drive);
}
@@ -746,8 +657,6 @@
if (speed > XFER_UDMA_5 || t == NULL)
return 1;
tr = kauai_lookup_timing(kauai_udma_timings, (int)t->udma);
- if (tr == 0)
- return 1;
*ultra_timings = ((*ultra_timings) & ~TR_100_UDMAREG_UDMA_MASK) | tr;
*ultra_timings = (*ultra_timings) | TR_100_UDMAREG_UDMA_EN;
@@ -766,8 +675,6 @@
if (speed > XFER_UDMA_6 || t == NULL)
return 1;
tr = kauai_lookup_timing(shasta_udma133_timings, (int)t->udma);
- if (tr == 0)
- return 1;
*ultra_timings = ((*ultra_timings) & ~TR_133_UDMAREG_UDMA_MASK) | tr;
*ultra_timings = (*ultra_timings) | TR_133_UDMAREG_UDMA_EN;
@@ -777,12 +684,13 @@
/*
* Calculate MDMA timings for all cells
*/
-static int
+static void
set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
- u8 speed, int drive_cycle_time)
+ u8 speed)
{
int cycleTime, accessTime = 0, recTime = 0;
unsigned accessTicks, recTicks;
+ struct hd_driveid *id = drive->id;
struct mdma_timings_t* tm = NULL;
int i;
@@ -792,11 +700,14 @@
case 1: cycleTime = 150; break;
case 2: cycleTime = 120; break;
default:
- return 1;
+ BUG();
+ break;
}
- /* Adjust for drive */
- if (drive_cycle_time && drive_cycle_time > cycleTime)
- cycleTime = drive_cycle_time;
+
+ /* Check if drive provides explicit DMA cycle time */
+ if ((id->field_valid & 2) && id->eide_dma_time)
+ cycleTime = max_t(int, id->eide_dma_time, cycleTime);
+
/* OHare limits according to some old Apple sources */
if ((intf_type == controller_ohare) && (cycleTime < 150))
cycleTime = 150;
@@ -824,8 +735,6 @@
break;
i++;
}
- if (i < 0)
- return 1;
cycleTime = tm[i].cycleTime;
accessTime = tm[i].accessTime;
recTime = tm[i].recoveryTime;
@@ -839,8 +748,6 @@
case controller_sh_ata6: {
/* 133Mhz cell */
u32 tr = kauai_lookup_timing(shasta_mdma_timings, cycleTime);
- if (tr == 0)
- return 1;
*timings = ((*timings) & ~TR_133_PIOREG_MDMA_MASK) | tr;
*timings2 = (*timings2) & ~TR_133_UDMAREG_UDMA_EN;
}
@@ -848,8 +755,6 @@
case controller_k2_ata6: {
/* 100Mhz cell */
u32 tr = kauai_lookup_timing(kauai_mdma_timings, cycleTime);
- if (tr == 0)
- return 1;
*timings = ((*timings) & ~TR_100_PIOREG_MDMA_MASK) | tr;
*timings2 = (*timings2) & ~TR_100_UDMAREG_UDMA_EN;
}
@@ -911,30 +816,23 @@
printk(KERN_ERR "%s: Set MDMA timing for mode %d, reg: 0x%08x\n",
drive->name, speed & 0xf, *timings);
#endif
- return 0;
}
#endif /* #ifdef CONFIG_BLK_DEV_IDEDMA_PMAC */
-/*
- * Speedproc. This function is called by the core to set any of the standard
- * DMA timing (MDMA or UDMA) to both the drive and the controller.
- * You may notice we don't use this function on normal "dma check" operation,
- * our dedicated function is more precise as it uses the drive provided
- * cycle time value. We should probably fix this one to deal with that too...
- */
-static int pmac_ide_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
int unit = (drive->select.b.unit & 0x01);
int ret = 0;
pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
- u32 *timings, *timings2;
+ u32 *timings, *timings2, tl[2];
- if (pmif == NULL)
- return 1;
-
timings = &pmif->timings[unit];
timings2 = &pmif->timings[unit+2];
-
+
+ /* Copy timings to local image */
+ tl[0] = *timings;
+ tl[1] = *timings2;
+
switch(speed) {
#ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
case XFER_UDMA_6:
@@ -945,38 +843,36 @@
case XFER_UDMA_1:
case XFER_UDMA_0:
if (pmif->kind == controller_kl_ata4)
- ret = set_timings_udma_ata4(timings, speed);
+ ret = set_timings_udma_ata4(&tl[0], speed);
else if (pmif->kind == controller_un_ata6
|| pmif->kind == controller_k2_ata6)
- ret = set_timings_udma_ata6(timings, timings2, speed);
+ ret = set_timings_udma_ata6(&tl[0], &tl[1], speed);
else if (pmif->kind == controller_sh_ata6)
- ret = set_timings_udma_shasta(timings, timings2, speed);
+ ret = set_timings_udma_shasta(&tl[0], &tl[1], speed);
else
- ret = 1;
+ ret = 1;
break;
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
- ret = set_timings_mdma(drive, pmif->kind, timings, timings2, speed, 0);
+ set_timings_mdma(drive, pmif->kind, &tl[0], &tl[1], speed);
break;
case XFER_SW_DMA_2:
case XFER_SW_DMA_1:
case XFER_SW_DMA_0:
- return 1;
+ return;
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
default:
ret = 1;
}
if (ret)
- return ret;
+ return;
- ret = pmac_ide_do_setfeature(drive, speed);
- if (ret)
- return ret;
-
+ /* Apply timings to controller */
+ *timings = tl[0];
+ *timings2 = tl[1];
+
pmac_ide_do_update_timings(drive);
-
- return 0;
}
/*
@@ -1236,6 +1132,10 @@
hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
hwif->drives[0].unmask = 1;
hwif->drives[1].unmask = 1;
+ hwif->drives[0].autotune = IDE_TUNE_AUTO;
+ hwif->drives[1].autotune = IDE_TUNE_AUTO;
+ hwif->host_flags = IDE_HFLAG_SET_PIO_MODE_KEEP_DMA |
+ IDE_HFLAG_POST_SET_MODE;
hwif->pio_mask = ATA_PIO4;
hwif->set_pio_mode = pmac_ide_set_pio_mode;
if (pmif->kind == controller_un_ata6
@@ -1244,7 +1144,7 @@
hwif->selectproc = pmac_ide_kauai_selectproc;
else
hwif->selectproc = pmac_ide_selectproc;
- hwif->speedproc = pmac_ide_tune_chipset;
+ hwif->set_dma_mode = pmac_ide_set_dma_mode;
printk(KERN_INFO "ide%d: Found Apple %s controller, bus ID %d%s, irq %d\n",
hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
@@ -1679,138 +1579,16 @@
}
/*
- * Pick up best MDMA timing for the drive and apply it
- */
-static int
-pmac_ide_mdma_enable(ide_drive_t *drive, u16 mode)
-{
- ide_hwif_t *hwif = HWIF(drive);
- pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
- int drive_cycle_time;
- struct hd_driveid *id = drive->id;
- u32 *timings, *timings2;
- u32 timing_local[2];
- int ret;
-
- /* which drive is it ? */
- timings = &pmif->timings[drive->select.b.unit & 0x01];
- timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
-
- /* Check if drive provide explicit cycle time */
- if ((id->field_valid & 2) && (id->eide_dma_time))
- drive_cycle_time = id->eide_dma_time;
- else
- drive_cycle_time = 0;
-
- /* Copy timings to local image */
- timing_local[0] = *timings;
- timing_local[1] = *timings2;
-
- /* Calculate controller timings */
- ret = set_timings_mdma( drive, pmif->kind,
- &timing_local[0],
- &timing_local[1],
- mode,
- drive_cycle_time);
- if (ret)
- return 0;
-
- /* Set feature on drive */
- printk(KERN_INFO "%s: Enabling MultiWord DMA %d\n", drive->name, mode & 0xf);
- ret = pmac_ide_do_setfeature(drive, mode);
- if (ret) {
- printk(KERN_WARNING "%s: Failed !\n", drive->name);
- return 0;
- }
-
- /* Apply timings to controller */
- *timings = timing_local[0];
- *timings2 = timing_local[1];
-
- return 1;
-}
-
-/*
- * Pick up best UDMA timing for the drive and apply it
- */
-static int
-pmac_ide_udma_enable(ide_drive_t *drive, u16 mode)
-{
- ide_hwif_t *hwif = HWIF(drive);
- pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
- u32 *timings, *timings2;
- u32 timing_local[2];
- int ret;
-
- /* which drive is it ? */
- timings = &pmif->timings[drive->select.b.unit & 0x01];
- timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
-
- /* Copy timings to local image */
- timing_local[0] = *timings;
- timing_local[1] = *timings2;
-
- /* Calculate timings for interface */
- if (pmif->kind == controller_un_ata6
- || pmif->kind == controller_k2_ata6)
- ret = set_timings_udma_ata6( &timing_local[0],
- &timing_local[1],
- mode);
- else if (pmif->kind == controller_sh_ata6)
- ret = set_timings_udma_shasta( &timing_local[0],
- &timing_local[1],
- mode);
- else
- ret = set_timings_udma_ata4(&timing_local[0], mode);
- if (ret)
- return 0;
-
- /* Set feature on drive */
- printk(KERN_INFO "%s: Enabling Ultra DMA %d\n", drive->name, mode & 0x0f);
- ret = pmac_ide_do_setfeature(drive, mode);
- if (ret) {
- printk(KERN_WARNING "%s: Failed !\n", drive->name);
- return 0;
- }
-
- /* Apply timings to controller */
- *timings = timing_local[0];
- *timings2 = timing_local[1];
-
- return 1;
-}
-
-/*
* Check what is the best DMA timing setting for the drive and
* call appropriate functions to apply it.
*/
static int
pmac_ide_dma_check(ide_drive_t *drive)
{
- struct hd_driveid *id = drive->id;
- ide_hwif_t *hwif = HWIF(drive);
- int enable = 1;
- drive->using_dma = 0;
-
- if (drive->media == ide_floppy)
- enable = 0;
- if (((id->capability & 1) == 0) && !__ide_dma_good_drive(drive))
- enable = 0;
- if (__ide_dma_bad_drive(drive))
- enable = 0;
+ if (ide_tune_dma(drive))
+ return 0;
- if (enable) {
- u8 mode = ide_max_dma_mode(drive);
-
- if (mode >= XFER_UDMA_0)
- drive->using_dma = pmac_ide_udma_enable(drive, mode);
- else if (mode >= XFER_MW_DMA_0)
- drive->using_dma = pmac_ide_mdma_enable(drive, mode);
- hwif->OUTB(0, IDE_CONTROL_REG);
- /* Apply settings to controller */
- pmac_ide_do_update_timings(drive);
- }
- return 0;
+ return -1;
}
/*
@@ -2044,7 +1822,10 @@
hwif->mwdma_mask = 0x07;
hwif->swdma_mask = 0x00;
break;
- }
+ }
+
+ hwif->autodma = 1;
+ hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
}
#endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 85d448b..02a27e8 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -681,7 +681,7 @@
u8 straight8; /* Alan's straight 8 check */
u8 bus_state; /* power state of the IDE bus */
- u8 host_flags;
+ u16 host_flags;
u8 pio_mask;
@@ -702,10 +702,10 @@
#if 0
ide_hwif_ops_t *hwifops;
#else
- /* routine to set PIO mode for drives */
+ /* routine to program host for PIO mode */
void (*set_pio_mode)(ide_drive_t *, const u8);
- /* routine to retune DMA modes for drives */
- int (*speedproc)(ide_drive_t *, const u8);
+ /* routine to program host for DMA mode */
+ void (*set_dma_mode)(ide_drive_t *, const u8);
/* tweaks hardware to select drive */
void (*selectproc)(ide_drive_t *);
/* chipset polling based on hba specifics */
@@ -1079,16 +1079,7 @@
*/
extern void ide_fixstring(u8 *, const int, const int);
-/*
- * This routine busy-waits for the drive status to be not "busy".
- * It then checks the status for all of the "good" bits and none
- * of the "bad" bits, and if all is okay it returns 0. All other
- * cases return 1 after doing "*startstop = ide_error()", and the
- * caller should return the updated value of "startstop" in this case.
- * "startstop" is unchanged when the function returns 0;
- * (startstop, drive, good, bad, timeout)
- */
-extern int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
+int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
/*
* Start a reset operation for an IDE interface.
@@ -1162,7 +1153,6 @@
extern void QUIRK_LIST(ide_drive_t *);
extern int drive_is_ready(ide_drive_t *);
-extern int wait_for_ready(ide_drive_t *, int /* timeout */);
/*
* taskfile io for disks for now...and builds request from ide_ioctl
@@ -1262,6 +1252,15 @@
IDE_HFLAG_ABUSE_FAST_DEVSEL = (1 << 5),
/* use 100-102 and 200-202 PIO values to set DMA modes */
IDE_HFLAG_ABUSE_DMA_MODES = (1 << 6),
+ /*
+ * keep DMA setting when programming PIO mode, may be used only
+ * for hosts which have separate PIO and DMA timings (ie. PMAC)
+ */
+ IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
+ /* program host for the transfer mode after programming device */
+ IDE_HFLAG_POST_SET_MODE = (1 << 8),
+ /* don't program host/device for the transfer mode ("smart" hosts) */
+ IDE_HFLAG_NO_SET_MODE = (1 << 9),
};
typedef struct ide_pci_device_s {
@@ -1278,7 +1277,7 @@
u8 bootable;
unsigned int extra;
struct ide_pci_device_s *next;
- u8 host_flags;
+ u16 host_flags;
u8 pio_mask;
u8 udma_mask;
} ide_pci_device_t;
@@ -1301,7 +1300,6 @@
#ifdef CONFIG_BLK_DEV_IDEDMA
int __ide_dma_bad_drive(ide_drive_t *);
-int __ide_dma_good_drive(ide_drive_t *);
u8 ide_find_dma_mode(ide_drive_t *, u8);
@@ -1420,6 +1418,9 @@
u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
extern const ide_pio_timings_t ide_pio_timings[6];
+int ide_set_pio_mode(ide_drive_t *, u8);
+int ide_set_dma_mode(ide_drive_t *, u8);
+
void ide_set_pio(ide_drive_t *, u8);
static inline void ide_set_max_pio(ide_drive_t *drive)