serial driver PMC MSP71xx
Serial driver patch for the PMC-Sierra MSP71xx devices.
There are three different fixes:
1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
16550 in that the THRE interrupt will not re-assert itself simply by
disabling and re-enabling the THRI bit in the IER, it is only re-enabled
if a character is actually sent out.
It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
also fixes it so we have dropped our initial workaround. This patch now
needs to be applied on top of that "mm" patch.
2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
which causes a new Busy Detect interrupt to be generated if it's busy
when the LCR is written. This fix saves the value of the LCR and
rewrites it after clearing the interrupt.
3 Workaround for interrupt/data concurrency issue: The SoC needs to
ensure that writes that can cause interrupts to be cleared reach the UART
before returning from the ISR. This fix reads a non-destructive register
on the UART so the read transaction completion ensures the previously
queued write transaction has also completed.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 90621c3..194362d 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -308,6 +308,7 @@
return inb(up->port.iobase + 1);
case UPIO_MEM:
+ case UPIO_DWAPB:
return readb(up->port.membase + offset);
case UPIO_MEM32:
@@ -333,6 +334,8 @@
static void
serial_out(struct uart_8250_port *up, int offset, int value)
{
+ /* Save the offset before it's remapped */
+ int save_offset = offset;
offset = map_8250_out_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
@@ -359,6 +362,18 @@
writeb(value, up->port.membase + offset);
break;
+ case UPIO_DWAPB:
+ /* Save the LCR value so it can be re-written when a
+ * Busy Detect interrupt occurs. */
+ if (save_offset == UART_LCR)
+ up->lcr = value;
+ writeb(value, up->port.membase + offset);
+ /* Read the IER to ensure any interrupt is cleared before
+ * returning from ISR. */
+ if (save_offset == UART_TX || save_offset == UART_IER)
+ value = serial_in(up, UART_IER);
+ break;
+
default:
outb(value, up->port.iobase + offset);
}
@@ -373,6 +388,7 @@
#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
#endif
+ case UPIO_DWAPB:
serial_out(up, offset, value);
serial_in(up, UART_LCR); /* safe, no side-effects */
break;
@@ -1389,6 +1405,19 @@
handled = 1;
end = NULL;
+ } else if (up->port.iotype == UPIO_DWAPB &&
+ (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
+ /* The DesignWare APB UART has an Busy Detect (0x07)
+ * interrupt meaning an LCR write attempt occured while the
+ * UART was busy. The interrupt must be cleared by reading
+ * the UART status register (USR) and the LCR re-written. */
+ unsigned int status;
+ status = *(volatile u32 *)up->port.private_data;
+ serial_out(up, UART_LCR, up->lcr);
+
+ handled = 1;
+
+ end = NULL;
} else if (end == NULL)
end = l;
@@ -2090,6 +2119,7 @@
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;
@@ -2127,6 +2157,7 @@
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;