mx31_3ds: revert 3ds debug board relate code
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/arch/arm/mach-mx3/Kconfig b/arch/arm/mach-mx3/Kconfig
index a11112a..e063657e 100644
--- a/arch/arm/mach-mx3/Kconfig
+++ b/arch/arm/mach-mx3/Kconfig
@@ -67,6 +67,7 @@
config MACH_MX31_3DS
bool "Support MX31PDK (3DS)"
select ARCH_MX31
+ select MXC_DEBUG_BOARD
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SPI_IMX
diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c
index d4d9e7a..6fe69e1 100644
--- a/arch/arm/mach-mx3/mach-mx31_3ds.c
+++ b/arch/arm/mach-mx3/mach-mx31_3ds.c
@@ -18,7 +18,6 @@
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/gpio.h>
-#include <linux/smsc911x.h>
#include <linux/platform_device.h>
#include <linux/mfd/mc13783.h>
#include <linux/spi/spi.h>
@@ -34,6 +33,7 @@
#include <asm/mach/map.h>
#include <mach/common.h>
#include <mach/iomux-mx3.h>
+#include <mach/3ds_debugboard.h>
#include "devices-imx31.h"
#include "devices.h"
@@ -254,173 +254,11 @@
};
/*
- * Support for the SMSC9217 on the Debug board.
- */
-
-static struct smsc911x_platform_config smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
- .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource smsc911x_resources[] = {
- {
- .start = LAN9217_BASE_ADDR,
- .end = LAN9217_BASE_ADDR + 0xff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = EXPIO_INT_ENET,
- .end = EXPIO_INT_ENET,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smsc911x_resources),
- .resource = smsc911x_resources,
- .dev = {
- .platform_data = &smsc911x_config,
- },
-};
-
-/*
- * Routines for the CPLD on the debug board. It contains a CPLD handling
- * LEDs, switches, interrupts for Ethernet.
- */
-
-static void mx31_3ds_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
-{
- uint32_t imr_val;
- uint32_t int_valid;
- uint32_t expio_irq;
-
- imr_val = __raw_readw(CPLD_INT_MASK_REG);
- int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val;
-
- expio_irq = MXC_EXP_IO_BASE;
- for (; int_valid != 0; int_valid >>= 1, expio_irq++) {
- if ((int_valid & 1) == 0)
- continue;
- generic_handle_irq(expio_irq);
- }
-}
-
-/*
- * Disable an expio pin's interrupt by setting the bit in the imr.
- * @param irq an expio virtual irq number
- */
-static void expio_mask_irq(uint32_t irq)
-{
- uint16_t reg;
- uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
- /* mask the interrupt */
- reg = __raw_readw(CPLD_INT_MASK_REG);
- reg |= 1 << expio;
- __raw_writew(reg, CPLD_INT_MASK_REG);
-}
-
-/*
- * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr.
- * @param irq an expanded io virtual irq number
- */
-static void expio_ack_irq(uint32_t irq)
-{
- uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
- /* clear the interrupt status */
- __raw_writew(1 << expio, CPLD_INT_RESET_REG);
- __raw_writew(0, CPLD_INT_RESET_REG);
- /* mask the interrupt */
- expio_mask_irq(irq);
-}
-
-/*
- * Enable a expio pin's interrupt by clearing the bit in the imr.
- * @param irq a expio virtual irq number
- */
-static void expio_unmask_irq(uint32_t irq)
-{
- uint16_t reg;
- uint32_t expio = MXC_IRQ_TO_EXPIO(irq);
-
- /* unmask the interrupt */
- reg = __raw_readw(CPLD_INT_MASK_REG);
- reg &= ~(1 << expio);
- __raw_writew(reg, CPLD_INT_MASK_REG);
-}
-
-static struct irq_chip expio_irq_chip = {
- .ack = expio_ack_irq,
- .mask = expio_mask_irq,
- .unmask = expio_unmask_irq,
-};
-
-static int __init mx31_3ds_init_expio(void)
-{
- int i;
- int ret;
-
- /* Check if there's a debug board connected */
- if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) ||
- (__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) ||
- (__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) {
- /* No Debug board found */
- return -ENODEV;
- }
-
- pr_info("i.MX31 3DS Debug board detected, rev = 0x%04X\n",
- __raw_readw(CPLD_CODE_VER_REG));
-
- /*
- * Configure INT line as GPIO input
- */
- ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq");
- if (ret)
- pr_warning("could not get LAN irq gpio\n");
- else
- gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1));
-
- /* Disable the interrupts and clear the status */
- __raw_writew(0, CPLD_INT_MASK_REG);
- __raw_writew(0xFFFF, CPLD_INT_RESET_REG);
- __raw_writew(0, CPLD_INT_RESET_REG);
- __raw_writew(0x1F, CPLD_INT_MASK_REG);
- for (i = MXC_EXP_IO_BASE;
- i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES);
- i++) {
- set_irq_chip(i, &expio_irq_chip);
- set_irq_handler(i, handle_level_irq);
- set_irq_flags(i, IRQF_VALID);
- }
- set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW);
- set_irq_chained_handler(EXPIO_PARENT_INT, mx31_3ds_expio_irq_handler);
-
- return 0;
-}
-
-/*
- * This structure defines the MX31 memory map.
- */
-static struct map_desc mx31_3ds_io_desc[] __initdata = {
- {
- .virtual = MX31_CS5_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
- .length = MX31_CS5_SIZE,
- .type = MT_DEVICE,
- },
-};
-
-/*
* Set up static virtual mappings.
*/
static void __init mx31_3ds_map_io(void)
{
mx31_map_io();
- iotable_init(mx31_3ds_io_desc, ARRAY_SIZE(mx31_3ds_io_desc));
}
/*!
@@ -443,8 +281,9 @@
mx31_3ds_usbotg_init();
mxc_register_device(&mxc_otg_udc_device, &usbotg_pdata);
- if (!mx31_3ds_init_expio())
- platform_device_register(&smsc911x_device);
+ if (!mxc_expio_init(CS5_BASE_ADDR, EXPIO_PARENT_INT))
+ printk(KERN_WARNING "Init of the debugboard failed, all "
+ "devices on the board are unusable.\n");
}
static void __init mx31_3ds_timer_init(void)