mmci: Add support for ST Micro derivate
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 1bcbdd6..2909bbc 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -430,6 +430,8 @@
clk = 255;
host->cclk = host->mclk / (2 * (clk + 1));
}
+ if (host->hw_designer == 0x80)
+ clk |= MCI_FCEN; /* Bug fix in ST IP block */
clk |= MCI_CLK_ENABLE;
}
@@ -440,15 +442,27 @@
case MMC_POWER_OFF:
break;
case MMC_POWER_UP:
- pwr |= MCI_PWR_UP;
- break;
+ /* The ST version does not have this, fall through to POWER_ON */
+ if (host->hw_designer != 0x80) {
+ pwr |= MCI_PWR_UP;
+ break;
+ }
case MMC_POWER_ON:
pwr |= MCI_PWR_ON;
break;
}
- if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
- pwr |= MCI_ROD;
+ if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
+ if (host->hw_designer != 0x80)
+ pwr |= MCI_ROD;
+ else {
+ /*
+ * The ST Micro variant use the ROD bit for something
+ * else and only has OD (Open Drain).
+ */
+ pwr |= MCI_OD;
+ }
+ }
writel(clk, host->base + MMCICLOCK);
@@ -500,6 +514,12 @@
}
host = mmc_priv(mmc);
+ /* Bits 12 thru 19 is the designer */
+ host->hw_designer = (dev->periphid >> 12) & 0xff;
+ /* Bits 20 thru 23 is the revison */
+ host->hw_revision = (dev->periphid >> 20) & 0xf;
+ DBG(host, "designer ID = 0x%02x\n", host->hw_designer);
+ DBG(host, "revision = 0x%01x\n", host->hw_revision);
host->clk = clk_get(&dev->dev, NULL);
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
@@ -693,6 +713,15 @@
.id = 0x00041181,
.mask = 0x000fffff,
},
+ /* ST Micro variants */
+ {
+ .id = 0x00180180,
+ .mask = 0x00ffffff,
+ },
+ {
+ .id = 0x00280180,
+ .mask = 0x00ffffff,
+ },
{ 0, 0 },
};
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 0f39c49..0441bac 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -11,13 +11,23 @@
#define MCI_PWR_OFF 0x00
#define MCI_PWR_UP 0x02
#define MCI_PWR_ON 0x03
+#define MCI_DATA2DIREN (1 << 2)
+#define MCI_CMDDIREN (1 << 3)
+#define MCI_DATA0DIREN (1 << 4)
+#define MCI_DATA31DIREN (1 << 5)
#define MCI_OD (1 << 6)
#define MCI_ROD (1 << 7)
+/* The ST Micro version does not have ROD */
+#define MCI_FBCLKEN (1 << 7)
+#define MCI_DATA74DIREN (1 << 8)
#define MMCICLOCK 0x004
#define MCI_CLK_ENABLE (1 << 8)
#define MCI_CLK_PWRSAVE (1 << 9)
#define MCI_CLK_BYPASS (1 << 10)
+#define MCI_WIDE_BUS (1 << 11)
+/* HW flow control on the ST Micro version */
+#define MCI_FCEN (1 << 13)
#define MMCIARGUMENT 0x008
#define MMCICOMMAND 0x00c
@@ -26,6 +36,10 @@
#define MCI_CPSM_INTERRUPT (1 << 8)
#define MCI_CPSM_PENDING (1 << 9)
#define MCI_CPSM_ENABLE (1 << 10)
+#define MCI_SDIO_SUSP (1 << 11)
+#define MCI_ENCMD_COMPL (1 << 12)
+#define MCI_NIEN (1 << 13)
+#define MCI_CE_ATACMD (1 << 14)
#define MMCIRESPCMD 0x010
#define MMCIRESPONSE0 0x014
@@ -39,6 +53,11 @@
#define MCI_DPSM_DIRECTION (1 << 1)
#define MCI_DPSM_MODE (1 << 2)
#define MCI_DPSM_DMAENABLE (1 << 3)
+#define MCI_DPSM_BLOCKSIZE (1 << 4)
+#define MCI_DPSM_RWSTART (1 << 8)
+#define MCI_DPSM_RWSTOP (1 << 9)
+#define MCI_DPSM_RWMOD (1 << 10)
+#define MCI_DPSM_SDIOEN (1 << 11)
#define MMCIDATACNT 0x030
#define MMCISTATUS 0x034
@@ -63,6 +82,8 @@
#define MCI_RXFIFOEMPTY (1 << 19)
#define MCI_TXDATAAVLBL (1 << 20)
#define MCI_RXDATAAVLBL (1 << 21)
+#define MCI_SDIOIT (1 << 22)
+#define MCI_CEATAEND (1 << 23)
#define MMCICLEAR 0x038
#define MCI_CMDCRCFAILCLR (1 << 0)
@@ -75,6 +96,8 @@
#define MCI_CMDSENTCLR (1 << 7)
#define MCI_DATAENDCLR (1 << 8)
#define MCI_DATABLOCKENDCLR (1 << 10)
+#define MCI_SDIOITC (1 << 22)
+#define MCI_CEATAENDC (1 << 23)
#define MMCIMASK0 0x03c
#define MCI_CMDCRCFAILMASK (1 << 0)
@@ -98,6 +121,8 @@
#define MCI_RXFIFOEMPTYMASK (1 << 19)
#define MCI_TXDATAAVLBLMASK (1 << 20)
#define MCI_RXDATAAVLBLMASK (1 << 21)
+#define MCI_SDIOITMASK (1 << 22)
+#define MCI_CEATAENDMASK (1 << 23)
#define MMCIMASK1 0x040
#define MMCIFIFOCNT 0x048
@@ -136,6 +161,9 @@
u32 pwr;
struct mmc_platform_data *plat;
+ u8 hw_designer;
+ u8 hw_revision:4;
+
struct timer_list timer;
unsigned int oldstat;