[ARM] Kirkwood: Marvell GuruPlug support
GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0
GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot
References:
http://www.globalscaletechnologies.com/t-guruplugdetails.aspx
http://plugcomputer.org
This patch is for GuruPlug Plus, but it supports Standard version
as well.
Signed-off-by: Siddarth Gore <gores@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 17879a8..05a8552 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -38,6 +38,12 @@
Say 'Y' here if you want your kernel to support the
Marvell eSATA SheevaPlug Reference Board.
+config MACH_GURUPLUG
+ bool "Marvell GuruPlug Reference Board"
+ help
+ Say 'Y' here if you want your kernel to support the
+ Marvell GuruPlug Reference Board.
+
config MACH_TS219
bool "QNAP TS-110, TS-119, TS-210, TS-219 and TS-219P Turbo NAS"
help
diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile
index a5530e3..85b3a39 100644
--- a/arch/arm/mach-kirkwood/Makefile
+++ b/arch/arm/mach-kirkwood/Makefile
@@ -6,6 +6,7 @@
obj-$(CONFIG_MACH_MV88F6281GTW_GE) += mv88f6281gtw_ge-setup.o
obj-$(CONFIG_MACH_SHEEVAPLUG) += sheevaplug-setup.o
obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o
+obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o
obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c
new file mode 100644
index 0000000..54d07c8
--- /dev/null
+++ b/arch/arm/mach-kirkwood/guruplug-setup.c
@@ -0,0 +1,131 @@
+/*
+ * arch/arm/mach-kirkwood/guruplug-setup.c
+ *
+ * Marvell GuruPlug Reference Board Setup
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include <plat/mvsdio.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition guruplug_nand_parts[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = SZ_1M
+ }, {
+ .name = "uImage",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_4M
+ }, {
+ .name = "root",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static struct mv643xx_eth_platform_data guruplug_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv643xx_eth_platform_data guruplug_ge01_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(1),
+};
+
+static struct mv_sata_platform_data guruplug_sata_data = {
+ .n_ports = 1,
+};
+
+static struct mvsdio_platform_data guruplug_mvsdio_data = {
+ /* unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led guruplug_led_pins[] = {
+ {
+ .name = "guruplug:red:health",
+ .gpio = 46,
+ .active_low = 1,
+ },
+ {
+ .name = "guruplug:green:health",
+ .gpio = 47,
+ .active_low = 1,
+ },
+ {
+ .name = "guruplug:red:wmode",
+ .gpio = 48,
+ .active_low = 1,
+ },
+ {
+ .name = "guruplug:green:wmode",
+ .gpio = 49,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data guruplug_led_data = {
+ .leds = guruplug_led_pins,
+ .num_leds = ARRAY_SIZE(guruplug_led_pins),
+};
+
+static struct platform_device guruplug_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &guruplug_led_data,
+ }
+};
+
+static unsigned int guruplug_mpp_config[] __initdata = {
+ MPP46_GPIO, /* M_RLED */
+ MPP47_GPIO, /* M_GLED */
+ MPP48_GPIO, /* B_RLED */
+ MPP49_GPIO, /* B_GLED */
+ 0
+};
+
+static void __init guruplug_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+ kirkwood_mpp_conf(guruplug_mpp_config);
+
+ kirkwood_uart0_init();
+ kirkwood_nand_init(ARRAY_AND_SIZE(guruplug_nand_parts), 25);
+
+ kirkwood_ehci_init();
+ kirkwood_ge00_init(&guruplug_ge00_data);
+ kirkwood_ge01_init(&guruplug_ge01_data);
+ kirkwood_sata_init(&guruplug_sata_data);
+ kirkwood_sdio_init(&guruplug_mvsdio_data);
+
+ platform_device_register(&guruplug_leds);
+}
+
+MACHINE_START(GURUPLUG, "Marvell GuruPlug Reference Board")
+ /* Maintainer: Siddarth Gore <gores@marvell.com> */
+ .phys_io = KIRKWOOD_REGS_PHYS_BASE,
+ .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
+ .init_machine = guruplug_init,
+ .map_io = kirkwood_map_io,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+MACHINE_END