blob: 5d2169809b19e03c4f69bb98640caa01e8bddb9b [file] [log] [blame]
#
# 8390 device configuration
#
config NET_VENDOR_8390
bool "National Semi-conductor 8390 devices"
depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \
ISA || MCA || EISA || MAC || M32R || MACH_TX49XX || \
MCA_LEGACY || H8300 || ARM || MIPS || ZORRO || PCMCIA || \
EXPERIMENTAL)
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Western Digital cards. If you say Y, you will be
asked for your specific card in the following questions.
if NET_VENDOR_8390
config EL2
tristate "3c503 \"EtherLink II\" support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called 3c503.
config AC3200
tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
depends on PCI && (ISA || EISA) && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called ac3200.
config PCMCIA_AXNET
tristate "Asix AX88190 PCMCIA support"
depends on PCMCIA
---help---
Say Y here if you intend to attach an Asix AX88190-based PCMCIA
(PC-card) Fast Ethernet card to your computer. These cards are
nearly NE2000 compatible but need a separate driver due to a few
misfeatures.
To compile this driver as a module, choose M here: the module will be
called axnet_cs. If unsure, say N.
config AX88796
tristate "ASIX AX88796 NE2000 clone support"
depends on (ARM || MIPS || SUPERH)
select PHYLIB
select MDIO_BITBANG
---help---
AX88796 driver, using platform bus to provide
chip detection and resources
config AX88796_93CX6
bool "ASIX AX88796 external 93CX6 eeprom support"
depends on AX88796
select EEPROM_93CX6
---help---
Select this if your platform comes with an external 93CX6 eeprom.
config E2100
tristate "Cabletron E21xx support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called e2100.
config ES3210
tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
depends on PCI && EISA && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called es3210.
config HPLAN_PLUS
tristate "HP PCLAN+ (27247B and 27252A) support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called hp-plus.
config HPLAN
tristate "HP PCLAN (27245 and other 27xxx series) support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called hp.
config HYDRA
tristate "Hydra support"
depends on ZORRO
select CRC32
---help---
If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
To compile this driver as a module, choose M here: the module
will be called hydra.
config ARM_ETHERH
tristate "I-cubed EtherH/ANT EtherM support"
depends on ARM && ARCH_ACORN
select CRC32
---help---
If you have an Acorn system with one of these network cards, you
should say Y to this option if you wish to use it with Linux.
config LNE390
tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
depends on PCI && EISA && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called lne390.
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
depends on MAC
select CRC32
---help---
If you want to include a driver to support Nubus or LC-PDS
Ethernet cards using an NS8390 chipset or its equivalent, say Y
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
config NE2000
tristate "NE2000/NE1000 support"
depends on (ISA || (Q40 && m) || M32R || MACH_TX49XX)
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>. Many Ethernet cards
without a specific driver are compatible with NE2000.
If you have a PCI NE2000 card however, say N here and Y to "PCI
NE2000 and clone support" under "EISA, VLB, PCI and on board
controllers" below. If you have a NE2000 card and are running on
an MCA system (a bus system used on some IBM PS/2 computers and
laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
below.
To compile this driver as a module, choose M here. The module
will be called ne.
config NE2_MCA
tristate "NE/2 (ne2000 MCA version) support"
depends on MCA_LEGACY
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called ne2.
config NE2K_PCI
tristate "PCI NE2000 and clones support (see help)"
depends on PCI
select CRC32
---help---
This driver is for NE2000 compatible PCI cards. It will not work
with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
support" below). If you have a PCI NE2000 network (Ethernet) card,
say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
This driver also works for the following NE2000 clone cards:
RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2
NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
Holtek HT80232 Holtek HT80229
To compile this driver as a module, choose M here. The module
will be called ne2k-pci.
config APNE
tristate "PCMCIA NE2000 support"
depends on AMIGA_PCMCIA
select CRC32
---help---
If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
say N.
To compile this driver as a module, choose M here: the module
will be called apne.
config NE3210
tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
depends on PCI && EISA && EXPERIMENTAL
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>. Note that this driver
will NOT WORK for NE3200 cards as they are completely different.
To compile this driver as a module, choose M here. The module
will be called ne3210.
config PCMCIA_PCNET
tristate "NE2000 compatible PCMCIA support"
depends on PCMCIA
select CRC32
---help---
Say Y here if you intend to attach an NE2000 compatible PCMCIA
(PC-card) Ethernet or Fast Ethernet card to your computer.
To compile this driver as a module, choose M here: the module will be
called pcnet_cs. If unsure, say N.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
depends on H8300
---help---
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
config STNIC
tristate "National DP83902AV support"
depends on SUPERH
select CRC32
---help---
Support for cards based on the National Semiconductor DP83902AV
ST-NIC Serial Network Interface Controller for Twisted Pair. This
is a 10Mbit/sec Ethernet controller. Product overview and specs at
<http://www.national.com/pf/DP/DP83902A.html>.
If unsure, say N.
config ULTRAMCA
tristate "SMC Ultra MCA support"
depends on MCA
select CRC32
---help---
If you have a network (Ethernet) card of this type and are running
an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
available from <http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called smc-mca.
config ULTRA
tristate "SMC Ultra support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Important: There have been many reports that, with some motherboards
mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
such as some BusLogic models) causes corruption problems with many
operating systems. The Linux smc-ultra driver has a work-around for
this but keep it in mind if you have such a SCSI card and have
problems.
To compile this driver as a module, choose M here. The module
will be called smc-ultra.
config ULTRA32
tristate "SMC Ultra32 EISA support"
depends on EISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called smc-ultra32.
config WD80x3
tristate "WD80*3 support"
depends on ISA
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called wd.
config ZORRO8390
tristate "Zorro NS8390-based Ethernet support"
depends on ZORRO
select CRC32
---help---
This driver is for Zorro Ethernet cards using an NS8390-compatible
chipset, like the Village Tronic Ariadne II and the Individual
Computers X-Surf Ethernet cards. If you have such a card, say Y.
Otherwise, say N.
To compile this driver as a module, choose M here: the module
will be called zorro8390.
endif # NET_VENDOR_8390