memcg: add page_cgroup flags for dirty page tracking
This patchset provides the ability for each cgroup to have independent
dirty page limits.
Limiting dirty memory is like fixing the max amount of dirty (hard to
reclaim) page cache used by a cgroup. So, in case of multiple cgroup
writers, they will not be able to consume more than their designated share
of dirty pages and will be forced to perform write-out if they cross that
limit.
The patches are based on a series proposed by Andrea Righi in Mar 2010.
Overview:
- Add page_cgroup flags to record when pages are dirty, in writeback, or nfs
unstable.
- Extend mem_cgroup to record the total number of pages in each of the
interesting dirty states (dirty, writeback, unstable_nfs).
- Add dirty parameters similar to the system-wide /proc/sys/vm/dirty_*
limits to mem_cgroup. The mem_cgroup dirty parameters are accessible
via cgroupfs control files.
- Consider both system and per-memcg dirty limits in page writeback when
deciding to queue background writeback or block for foreground writeback.
Known shortcomings:
- When a cgroup dirty limit is exceeded, then bdi writeback is employed to
writeback dirty inodes. Bdi writeback considers inodes from any cgroup, not
just inodes contributing dirty pages to the cgroup exceeding its limit.
- When memory.use_hierarchy is set, then dirty limits are disabled. This is a
implementation detail. An enhanced implementation is needed to check the
chain of parents to ensure that no dirty limit is exceeded.
Performance data:
- A page fault microbenchmark workload was used to measure performance, which
can be called in read or write mode:
f = open(foo. $cpu)
truncate(f, 4096)
alarm(60)
while (1) {
p = mmap(f, 4096)
if (write)
*p = 1
else
x = *p
munmap(p)
}
- The workload was called for several points in the patch series in different
modes:
- s_read is a single threaded reader
- s_write is a single threaded writer
- p_read is a 16 thread reader, each operating on a different file
- p_write is a 16 thread writer, each operating on a different file
- Measurements were collected on a 16 core non-numa system using "perf stat
--repeat 3". The -a option was used for parallel (p_*) runs.
- All numbers are page fault rate (M/sec). Higher is better.
- To compare the performance of a kernel without non-memcg compare the first and
last rows, neither has memcg configured. The first row does not include any
of these memcg patches.
- To compare the performance of using memcg dirty limits, compare the baseline
(2nd row titled "w/ memcg") with the the code and memcg enabled (2nd to last
row titled "all patches").
root_cgroup child_cgroup
s_read s_write p_read p_write s_read s_write p_read p_write
mmotm w/o memcg 0.428 0.390 0.429 0.388
mmotm w/ memcg 0.411 0.378 0.391 0.362 0.412 0.377 0.385 0.363
all patches 0.384 0.360 0.370 0.348 0.381 0.363 0.368 0.347
all patches 0.431 0.402 0.427 0.395
w/o memcg
This patch:
Add additional flags to page_cgroup to track dirty pages within a
mem_cgroup.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrea Righi <arighi@develer.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1 file changed