[SCSI] mvsas: split driver into multiple files
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
diff --git a/drivers/scsi/mvsas/mv_64xx.h b/drivers/scsi/mvsas/mv_64xx.h
new file mode 100644
index 0000000..c9f399e
--- /dev/null
+++ b/drivers/scsi/mvsas/mv_64xx.h
@@ -0,0 +1,92 @@
+#ifndef _MVS64XX_REG_H_
+#define _MVS64XX_REG_H_
+
+/* enhanced mode registers (BAR4) */
+enum hw_registers {
+ MVS_GBL_CTL = 0x04, /* global control */
+ MVS_GBL_INT_STAT = 0x08, /* global irq status */
+ MVS_GBL_PI = 0x0C, /* ports implemented bitmask */
+ MVS_GBL_PORT_TYPE = 0xa0, /* port type */
+
+ MVS_CTL = 0x100, /* SAS/SATA port configuration */
+ MVS_PCS = 0x104, /* SAS/SATA port control/status */
+ MVS_CMD_LIST_LO = 0x108, /* cmd list addr */
+ MVS_CMD_LIST_HI = 0x10C,
+ MVS_RX_FIS_LO = 0x110, /* RX FIS list addr */
+ MVS_RX_FIS_HI = 0x114,
+
+ MVS_TX_CFG = 0x120, /* TX configuration */
+ MVS_TX_LO = 0x124, /* TX (delivery) ring addr */
+ MVS_TX_HI = 0x128,
+
+ MVS_TX_PROD_IDX = 0x12C, /* TX producer pointer */
+ MVS_TX_CONS_IDX = 0x130, /* TX consumer pointer (RO) */
+ MVS_RX_CFG = 0x134, /* RX configuration */
+ MVS_RX_LO = 0x138, /* RX (completion) ring addr */
+ MVS_RX_HI = 0x13C,
+ MVS_RX_CONS_IDX = 0x140, /* RX consumer pointer (RO) */
+
+ MVS_INT_COAL = 0x148, /* Int coalescing config */
+ MVS_INT_COAL_TMOUT = 0x14C, /* Int coalescing timeout */
+ MVS_INT_STAT = 0x150, /* Central int status */
+ MVS_INT_MASK = 0x154, /* Central int enable */
+ MVS_INT_STAT_SRS = 0x158, /* SATA register set status */
+ MVS_INT_MASK_SRS = 0x15C,
+
+ /* ports 1-3 follow after this */
+ MVS_P0_INT_STAT = 0x160, /* port0 interrupt status */
+ MVS_P0_INT_MASK = 0x164, /* port0 interrupt mask */
+ MVS_P4_INT_STAT = 0x200, /* Port 4 interrupt status */
+ MVS_P4_INT_MASK = 0x204, /* Port 4 interrupt enable mask */
+
+ /* ports 1-3 follow after this */
+ MVS_P0_SER_CTLSTAT = 0x180, /* port0 serial control/status */
+ MVS_P4_SER_CTLSTAT = 0x220, /* port4 serial control/status */
+
+ MVS_CMD_ADDR = 0x1B8, /* Command register port (addr) */
+ MVS_CMD_DATA = 0x1BC, /* Command register port (data) */
+
+ /* ports 1-3 follow after this */
+ MVS_P0_CFG_ADDR = 0x1C0, /* port0 phy register address */
+ MVS_P0_CFG_DATA = 0x1C4, /* port0 phy register data */
+ MVS_P4_CFG_ADDR = 0x230, /* Port 4 config address */
+ MVS_P4_CFG_DATA = 0x234, /* Port 4 config data */
+
+ /* ports 1-3 follow after this */
+ MVS_P0_VSR_ADDR = 0x1E0, /* port0 VSR address */
+ MVS_P0_VSR_DATA = 0x1E4, /* port0 VSR data */
+ MVS_P4_VSR_ADDR = 0x250, /* port 4 VSR addr */
+ MVS_P4_VSR_DATA = 0x254, /* port 4 VSR data */
+};
+
+enum pci_cfg_registers {
+ PCR_PHY_CTL = 0x40,
+ PCR_PHY_CTL2 = 0x90,
+ PCR_DEV_CTRL = 0xE8,
+};
+
+/* SAS/SATA Vendor Specific Port Registers */
+enum sas_sata_vsp_regs {
+ VSR_PHY_STAT = 0x00, /* Phy Status */
+ VSR_PHY_MODE1 = 0x01, /* phy tx */
+ VSR_PHY_MODE2 = 0x02, /* tx scc */
+ VSR_PHY_MODE3 = 0x03, /* pll */
+ VSR_PHY_MODE4 = 0x04, /* VCO */
+ VSR_PHY_MODE5 = 0x05, /* Rx */
+ VSR_PHY_MODE6 = 0x06, /* CDR */
+ VSR_PHY_MODE7 = 0x07, /* Impedance */
+ VSR_PHY_MODE8 = 0x08, /* Voltage */
+ VSR_PHY_MODE9 = 0x09, /* Test */
+ VSR_PHY_MODE10 = 0x0A, /* Power */
+ VSR_PHY_MODE11 = 0x0B, /* Phy Mode */
+ VSR_PHY_VS0 = 0x0C, /* Vednor Specific 0 */
+ VSR_PHY_VS1 = 0x0D, /* Vednor Specific 1 */
+};
+
+struct mvs_prd {
+ __le64 addr; /* 64-bit buffer address */
+ __le32 reserved;
+ __le32 len; /* 16-bit length */
+};
+
+#endif