IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters
Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
diff --git a/drivers/infiniband/hw/qib/qib_iba6120.c b/drivers/infiniband/hw/qib/qib_iba6120.c
new file mode 100644
index 0000000..7b6549f
--- /dev/null
+++ b/drivers/infiniband/hw/qib/qib_iba6120.c
@@ -0,0 +1,3588 @@
+/*
+ * Copyright (c) 2006, 2007, 2008, 2009, 2010 QLogic Corporation.
+ * All rights reserved.
+ * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
+ *
+ * This software is available to you under a choice of one of two
+ * licenses. You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the
+ * OpenIB.org BSD license below:
+ *
+ * Redistribution and use in source and binary forms, with or
+ * without modification, are permitted provided that the following
+ * conditions are met:
+ *
+ * - Redistributions of source code must retain the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer.
+ *
+ * - Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials
+ * provided with the distribution.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
+ * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
+ * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
+ * SOFTWARE.
+ */
+/*
+ * This file contains all of the code that is specific to the
+ * QLogic_IB 6120 PCIe chip.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <rdma/ib_verbs.h>
+
+#include "qib.h"
+#include "qib_6120_regs.h"
+
+static void qib_6120_setup_setextled(struct qib_pportdata *, u32);
+static void sendctrl_6120_mod(struct qib_pportdata *ppd, u32 op);
+static u8 qib_6120_phys_portstate(u64);
+static u32 qib_6120_iblink_state(u64);
+
+/*
+ * This file contains all the chip-specific register information and
+ * access functions for the QLogic QLogic_IB PCI-Express chip.
+ *
+ */
+
+/* KREG_IDX uses machine-generated #defines */
+#define KREG_IDX(regname) (QIB_6120_##regname##_OFFS / sizeof(u64))
+
+/* Use defines to tie machine-generated names to lower-case names */
+#define kr_extctrl KREG_IDX(EXTCtrl)
+#define kr_extstatus KREG_IDX(EXTStatus)
+#define kr_gpio_clear KREG_IDX(GPIOClear)
+#define kr_gpio_mask KREG_IDX(GPIOMask)
+#define kr_gpio_out KREG_IDX(GPIOOut)
+#define kr_gpio_status KREG_IDX(GPIOStatus)
+#define kr_rcvctrl KREG_IDX(RcvCtrl)
+#define kr_sendctrl KREG_IDX(SendCtrl)
+#define kr_partitionkey KREG_IDX(RcvPartitionKey)
+#define kr_hwdiagctrl KREG_IDX(HwDiagCtrl)
+#define kr_ibcstatus KREG_IDX(IBCStatus)
+#define kr_ibcctrl KREG_IDX(IBCCtrl)
+#define kr_sendbuffererror KREG_IDX(SendBufErr0)
+#define kr_rcvbthqp KREG_IDX(RcvBTHQP)
+#define kr_counterregbase KREG_IDX(CntrRegBase)
+#define kr_palign KREG_IDX(PageAlign)
+#define kr_rcvegrbase KREG_IDX(RcvEgrBase)
+#define kr_rcvegrcnt KREG_IDX(RcvEgrCnt)
+#define kr_rcvhdrcnt KREG_IDX(RcvHdrCnt)
+#define kr_rcvhdrentsize KREG_IDX(RcvHdrEntSize)
+#define kr_rcvhdrsize KREG_IDX(RcvHdrSize)
+#define kr_rcvtidbase KREG_IDX(RcvTIDBase)
+#define kr_rcvtidcnt KREG_IDX(RcvTIDCnt)
+#define kr_scratch KREG_IDX(Scratch)
+#define kr_sendctrl KREG_IDX(SendCtrl)
+#define kr_sendpioavailaddr KREG_IDX(SendPIOAvailAddr)
+#define kr_sendpiobufbase KREG_IDX(SendPIOBufBase)
+#define kr_sendpiobufcnt KREG_IDX(SendPIOBufCnt)
+#define kr_sendpiosize KREG_IDX(SendPIOSize)
+#define kr_sendregbase KREG_IDX(SendRegBase)
+#define kr_userregbase KREG_IDX(UserRegBase)
+#define kr_control KREG_IDX(Control)
+#define kr_intclear KREG_IDX(IntClear)
+#define kr_intmask KREG_IDX(IntMask)
+#define kr_intstatus KREG_IDX(IntStatus)
+#define kr_errclear KREG_IDX(ErrClear)
+#define kr_errmask KREG_IDX(ErrMask)
+#define kr_errstatus KREG_IDX(ErrStatus)
+#define kr_hwerrclear KREG_IDX(HwErrClear)
+#define kr_hwerrmask KREG_IDX(HwErrMask)
+#define kr_hwerrstatus KREG_IDX(HwErrStatus)
+#define kr_revision KREG_IDX(Revision)
+#define kr_portcnt KREG_IDX(PortCnt)
+#define kr_serdes_cfg0 KREG_IDX(SerdesCfg0)
+#define kr_serdes_cfg1 (kr_serdes_cfg0 + 1)
+#define kr_serdes_stat KREG_IDX(SerdesStat)
+#define kr_xgxs_cfg KREG_IDX(XGXSCfg)
+
+/* These must only be written via qib_write_kreg_ctxt() */
+#define kr_rcvhdraddr KREG_IDX(RcvHdrAddr0)
+#define kr_rcvhdrtailaddr KREG_IDX(RcvHdrTailAddr0)
+
+#define CREG_IDX(regname) ((QIB_6120_##regname##_OFFS - \
+ QIB_6120_LBIntCnt_OFFS) / sizeof(u64))
+
+#define cr_badformat CREG_IDX(RxBadFormatCnt)
+#define cr_erricrc CREG_IDX(RxICRCErrCnt)
+#define cr_errlink CREG_IDX(RxLinkProblemCnt)
+#define cr_errlpcrc CREG_IDX(RxLPCRCErrCnt)
+#define cr_errpkey CREG_IDX(RxPKeyMismatchCnt)
+#define cr_rcvflowctrl_err CREG_IDX(RxFlowCtrlErrCnt)
+#define cr_err_rlen CREG_IDX(RxLenErrCnt)
+#define cr_errslen CREG_IDX(TxLenErrCnt)
+#define cr_errtidfull CREG_IDX(RxTIDFullErrCnt)
+#define cr_errtidvalid CREG_IDX(RxTIDValidErrCnt)
+#define cr_errvcrc CREG_IDX(RxVCRCErrCnt)
+#define cr_ibstatuschange CREG_IDX(IBStatusChangeCnt)
+#define cr_lbint CREG_IDX(LBIntCnt)
+#define cr_invalidrlen CREG_IDX(RxMaxMinLenErrCnt)
+#define cr_invalidslen CREG_IDX(TxMaxMinLenErrCnt)
+#define cr_lbflowstall CREG_IDX(LBFlowStallCnt)
+#define cr_pktrcv CREG_IDX(RxDataPktCnt)
+#define cr_pktrcvflowctrl CREG_IDX(RxFlowPktCnt)
+#define cr_pktsend CREG_IDX(TxDataPktCnt)
+#define cr_pktsendflow CREG_IDX(TxFlowPktCnt)
+#define cr_portovfl CREG_IDX(RxP0HdrEgrOvflCnt)
+#define cr_rcvebp CREG_IDX(RxEBPCnt)
+#define cr_rcvovfl CREG_IDX(RxBufOvflCnt)
+#define cr_senddropped CREG_IDX(TxDroppedPktCnt)
+#define cr_sendstall CREG_IDX(TxFlowStallCnt)
+#define cr_sendunderrun CREG_IDX(TxUnderrunCnt)
+#define cr_wordrcv CREG_IDX(RxDwordCnt)
+#define cr_wordsend CREG_IDX(TxDwordCnt)
+#define cr_txunsupvl CREG_IDX(TxUnsupVLErrCnt)
+#define cr_rxdroppkt CREG_IDX(RxDroppedPktCnt)
+#define cr_iblinkerrrecov CREG_IDX(IBLinkErrRecoveryCnt)
+#define cr_iblinkdown CREG_IDX(IBLinkDownedCnt)
+#define cr_ibsymbolerr CREG_IDX(IBSymbolErrCnt)
+
+#define SYM_RMASK(regname, fldname) ((u64) \
+ QIB_6120_##regname##_##fldname##_RMASK)
+#define SYM_MASK(regname, fldname) ((u64) \
+ QIB_6120_##regname##_##fldname##_RMASK << \
+ QIB_6120_##regname##_##fldname##_LSB)
+#define SYM_LSB(regname, fldname) (QIB_6120_##regname##_##fldname##_LSB)
+
+#define SYM_FIELD(value, regname, fldname) ((u64) \
+ (((value) >> SYM_LSB(regname, fldname)) & \
+ SYM_RMASK(regname, fldname)))
+#define ERR_MASK(fldname) SYM_MASK(ErrMask, fldname##Mask)
+#define HWE_MASK(fldname) SYM_MASK(HwErrMask, fldname##Mask)
+
+/* link training states, from IBC */
+#define IB_6120_LT_STATE_DISABLED 0x00
+#define IB_6120_LT_STATE_LINKUP 0x01
+#define IB_6120_LT_STATE_POLLACTIVE 0x02
+#define IB_6120_LT_STATE_POLLQUIET 0x03
+#define IB_6120_LT_STATE_SLEEPDELAY 0x04
+#define IB_6120_LT_STATE_SLEEPQUIET 0x05
+#define IB_6120_LT_STATE_CFGDEBOUNCE 0x08
+#define IB_6120_LT_STATE_CFGRCVFCFG 0x09
+#define IB_6120_LT_STATE_CFGWAITRMT 0x0a
+#define IB_6120_LT_STATE_CFGIDLE 0x0b
+#define IB_6120_LT_STATE_RECOVERRETRAIN 0x0c
+#define IB_6120_LT_STATE_RECOVERWAITRMT 0x0e
+#define IB_6120_LT_STATE_RECOVERIDLE 0x0f
+
+/* link state machine states from IBC */
+#define IB_6120_L_STATE_DOWN 0x0
+#define IB_6120_L_STATE_INIT 0x1
+#define IB_6120_L_STATE_ARM 0x2
+#define IB_6120_L_STATE_ACTIVE 0x3
+#define IB_6120_L_STATE_ACT_DEFER 0x4
+
+static const u8 qib_6120_physportstate[0x20] = {
+ [IB_6120_LT_STATE_DISABLED] = IB_PHYSPORTSTATE_DISABLED,
+ [IB_6120_LT_STATE_LINKUP] = IB_PHYSPORTSTATE_LINKUP,
+ [IB_6120_LT_STATE_POLLACTIVE] = IB_PHYSPORTSTATE_POLL,
+ [IB_6120_LT_STATE_POLLQUIET] = IB_PHYSPORTSTATE_POLL,
+ [IB_6120_LT_STATE_SLEEPDELAY] = IB_PHYSPORTSTATE_SLEEP,
+ [IB_6120_LT_STATE_SLEEPQUIET] = IB_PHYSPORTSTATE_SLEEP,
+ [IB_6120_LT_STATE_CFGDEBOUNCE] =
+ IB_PHYSPORTSTATE_CFG_TRAIN,
+ [IB_6120_LT_STATE_CFGRCVFCFG] =
+ IB_PHYSPORTSTATE_CFG_TRAIN,
+ [IB_6120_LT_STATE_CFGWAITRMT] =
+ IB_PHYSPORTSTATE_CFG_TRAIN,
+ [IB_6120_LT_STATE_CFGIDLE] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [IB_6120_LT_STATE_RECOVERRETRAIN] =
+ IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
+ [IB_6120_LT_STATE_RECOVERWAITRMT] =
+ IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
+ [IB_6120_LT_STATE_RECOVERIDLE] =
+ IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
+ [0x10] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x11] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x12] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x13] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x14] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x15] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x16] = IB_PHYSPORTSTATE_CFG_TRAIN,
+ [0x17] = IB_PHYSPORTSTATE_CFG_TRAIN
+};
+
+
+struct qib_chip_specific {
+ u64 __iomem *cregbase;
+ u64 *cntrs;
+ u64 *portcntrs;
+ void *dummy_hdrq; /* used after ctxt close */
+ dma_addr_t dummy_hdrq_phys;
+ spinlock_t kernel_tid_lock; /* no back to back kernel TID writes */
+ spinlock_t user_tid_lock; /* no back to back user TID writes */
+ spinlock_t rcvmod_lock; /* protect rcvctrl shadow changes */
+ spinlock_t gpio_lock; /* RMW of shadows/regs for ExtCtrl and GPIO */
+ u64 hwerrmask;
+ u64 errormask;
+ u64 gpio_out; /* shadow of kr_gpio_out, for rmw ops */
+ u64 gpio_mask; /* shadow the gpio mask register */
+ u64 extctrl; /* shadow the gpio output enable, etc... */
+ /*
+ * these 5 fields are used to establish deltas for IB symbol
+ * errors and linkrecovery errors. They can be reported on
+ * some chips during link negotiation prior to INIT, and with
+ * DDR when faking DDR negotiations with non-IBTA switches.
+ * The chip counters are adjusted at driver unload if there is
+ * a non-zero delta.
+ */
+ u64 ibdeltainprog;
+ u64 ibsymdelta;
+ u64 ibsymsnap;
+ u64 iblnkerrdelta;
+ u64 iblnkerrsnap;
+ u64 ibcctrl; /* shadow for kr_ibcctrl */
+ u32 lastlinkrecov; /* link recovery issue */
+ int irq;
+ u32 cntrnamelen;
+ u32 portcntrnamelen;
+ u32 ncntrs;
+ u32 nportcntrs;
+ /* used with gpio interrupts to implement IB counters */
+ u32 rxfc_unsupvl_errs;
+ u32 overrun_thresh_errs;
+ /*
+ * these count only cases where _successive_ LocalLinkIntegrity
+ * errors were seen in the receive headers of IB standard packets
+ */
+ u32 lli_errs;
+ u32 lli_counter;
+ u64 lli_thresh;
+ u64 sword; /* total dwords sent (sample result) */
+ u64 rword; /* total dwords received (sample result) */
+ u64 spkts; /* total packets sent (sample result) */
+ u64 rpkts; /* total packets received (sample result) */
+ u64 xmit_wait; /* # of ticks no data sent (sample result) */
+ struct timer_list pma_timer;
+ char emsgbuf[128];
+ char bitsmsgbuf[64];
+ u8 pma_sample_status;
+};
+
+/* ibcctrl bits */
+#define QLOGIC_IB_IBCC_LINKINITCMD_DISABLE 1
+/* cycle through TS1/TS2 till OK */
+#define QLOGIC_IB_IBCC_LINKINITCMD_POLL 2
+/* wait for TS1, then go on */
+#define QLOGIC_IB_IBCC_LINKINITCMD_SLEEP 3
+#define QLOGIC_IB_IBCC_LINKINITCMD_SHIFT 16
+
+#define QLOGIC_IB_IBCC_LINKCMD_DOWN 1 /* move to 0x11 */
+#define QLOGIC_IB_IBCC_LINKCMD_ARMED 2 /* move to 0x21 */
+#define QLOGIC_IB_IBCC_LINKCMD_ACTIVE 3 /* move to 0x31 */
+#define QLOGIC_IB_IBCC_LINKCMD_SHIFT 18
+
+/*
+ * We could have a single register get/put routine, that takes a group type,
+ * but this is somewhat clearer and cleaner. It also gives us some error
+ * checking. 64 bit register reads should always work, but are inefficient
+ * on opteron (the northbridge always generates 2 separate HT 32 bit reads),
+ * so we use kreg32 wherever possible. User register and counter register
+ * reads are always 32 bit reads, so only one form of those routines.
+ */
+
+/**
+ * qib_read_ureg32 - read 32-bit virtualized per-context register
+ * @dd: device
+ * @regno: register number
+ * @ctxt: context number
+ *
+ * Return the contents of a register that is virtualized to be per context.
+ * Returns -1 on errors (not distinguishable from valid contents at
+ * runtime; we may add a separate error variable at some point).
+ */
+static inline u32 qib_read_ureg32(const struct qib_devdata *dd,
+ enum qib_ureg regno, int ctxt)
+{
+ if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
+ return 0;
+
+ if (dd->userbase)
+ return readl(regno + (u64 __iomem *)
+ ((char __iomem *)dd->userbase +
+ dd->ureg_align * ctxt));
+ else
+ return readl(regno + (u64 __iomem *)
+ (dd->uregbase +
+ (char __iomem *)dd->kregbase +
+ dd->ureg_align * ctxt));
+}
+
+/**
+ * qib_write_ureg - write 32-bit virtualized per-context register
+ * @dd: device
+ * @regno: register number
+ * @value: value
+ * @ctxt: context
+ *
+ * Write the contents of a register that is virtualized to be per context.
+ */
+static inline void qib_write_ureg(const struct qib_devdata *dd,
+ enum qib_ureg regno, u64 value, int ctxt)
+{
+ u64 __iomem *ubase;
+ if (dd->userbase)
+ ubase = (u64 __iomem *)
+ ((char __iomem *) dd->userbase +
+ dd->ureg_align * ctxt);
+ else
+ ubase = (u64 __iomem *)
+ (dd->uregbase +
+ (char __iomem *) dd->kregbase +
+ dd->ureg_align * ctxt);
+
+ if (dd->kregbase && (dd->flags & QIB_PRESENT))
+ writeq(value, &ubase[regno]);
+}
+
+static inline u32 qib_read_kreg32(const struct qib_devdata *dd,
+ const u16 regno)
+{
+ if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
+ return -1;
+ return readl((u32 __iomem *)&dd->kregbase[regno]);
+}
+
+static inline u64 qib_read_kreg64(const struct qib_devdata *dd,
+ const u16 regno)
+{
+ if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
+ return -1;
+
+ return readq(&dd->kregbase[regno]);
+}
+
+static inline void qib_write_kreg(const struct qib_devdata *dd,
+ const u16 regno, u64 value)
+{
+ if (dd->kregbase && (dd->flags & QIB_PRESENT))
+ writeq(value, &dd->kregbase[regno]);
+}
+
+/**
+ * qib_write_kreg_ctxt - write a device's per-ctxt 64-bit kernel register
+ * @dd: the qlogic_ib device
+ * @regno: the register number to write
+ * @ctxt: the context containing the register
+ * @value: the value to write
+ */
+static inline void qib_write_kreg_ctxt(const struct qib_devdata *dd,
+ const u16 regno, unsigned ctxt,
+ u64 value)
+{
+ qib_write_kreg(dd, regno + ctxt, value);
+}
+
+static inline void write_6120_creg(const struct qib_devdata *dd,
+ u16 regno, u64 value)
+{
+ if (dd->cspec->cregbase && (dd->flags & QIB_PRESENT))
+ writeq(value, &dd->cspec->cregbase[regno]);
+}
+
+static inline u64 read_6120_creg(const struct qib_devdata *dd, u16 regno)
+{
+ if (!dd->cspec->cregbase || !(dd->flags & QIB_PRESENT))
+ return 0;
+ return readq(&dd->cspec->cregbase[regno]);
+}
+
+static inline u32 read_6120_creg32(const struct qib_devdata *dd, u16 regno)
+{
+ if (!dd->cspec->cregbase || !(dd->flags & QIB_PRESENT))
+ return 0;
+ return readl(&dd->cspec->cregbase[regno]);
+}
+
+/* kr_control bits */
+#define QLOGIC_IB_C_RESET 1U
+
+/* kr_intstatus, kr_intclear, kr_intmask bits */
+#define QLOGIC_IB_I_RCVURG_MASK ((1U << 5) - 1)
+#define QLOGIC_IB_I_RCVURG_SHIFT 0
+#define QLOGIC_IB_I_RCVAVAIL_MASK ((1U << 5) - 1)
+#define QLOGIC_IB_I_RCVAVAIL_SHIFT 12
+
+#define QLOGIC_IB_C_FREEZEMODE 0x00000002
+#define QLOGIC_IB_C_LINKENABLE 0x00000004
+#define QLOGIC_IB_I_ERROR 0x0000000080000000ULL
+#define QLOGIC_IB_I_SPIOSENT 0x0000000040000000ULL
+#define QLOGIC_IB_I_SPIOBUFAVAIL 0x0000000020000000ULL
+#define QLOGIC_IB_I_GPIO 0x0000000010000000ULL
+#define QLOGIC_IB_I_BITSEXTANT \
+ ((QLOGIC_IB_I_RCVURG_MASK << QLOGIC_IB_I_RCVURG_SHIFT) | \
+ (QLOGIC_IB_I_RCVAVAIL_MASK << \
+ QLOGIC_IB_I_RCVAVAIL_SHIFT) | \
+ QLOGIC_IB_I_ERROR | QLOGIC_IB_I_SPIOSENT | \
+ QLOGIC_IB_I_SPIOBUFAVAIL | QLOGIC_IB_I_GPIO)
+
+/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
+#define QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL
+#define QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT 0
+#define QLOGIC_IB_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL
+#define QLOGIC_IB_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL
+#define QLOGIC_IB_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL
+#define QLOGIC_IB_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL
+#define QLOGIC_IB_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL
+#define QLOGIC_IB_HWE_COREPLL_FBSLIP 0x0080000000000000ULL
+#define QLOGIC_IB_HWE_COREPLL_RFSLIP 0x0100000000000000ULL
+#define QLOGIC_IB_HWE_PCIE1PLLFAILED 0x0400000000000000ULL
+#define QLOGIC_IB_HWE_PCIE0PLLFAILED 0x0800000000000000ULL
+#define QLOGIC_IB_HWE_SERDESPLLFAILED 0x1000000000000000ULL
+
+
+/* kr_extstatus bits */
+#define QLOGIC_IB_EXTS_FREQSEL 0x2
+#define QLOGIC_IB_EXTS_SERDESSEL 0x4
+#define QLOGIC_IB_EXTS_MEMBIST_ENDTEST 0x0000000000004000
+#define QLOGIC_IB_EXTS_MEMBIST_FOUND 0x0000000000008000
+
+/* kr_xgxsconfig bits */
+#define QLOGIC_IB_XGXS_RESET 0x5ULL
+
+#define _QIB_GPIO_SDA_NUM 1
+#define _QIB_GPIO_SCL_NUM 0
+
+/* Bits in GPIO for the added IB link interrupts */
+#define GPIO_RXUVL_BIT 3
+#define GPIO_OVRUN_BIT 4
+#define GPIO_LLI_BIT 5
+#define GPIO_ERRINTR_MASK 0x38
+
+
+#define QLOGIC_IB_RT_BUFSIZE_MASK 0xe0000000ULL
+#define QLOGIC_IB_RT_BUFSIZE_SHIFTVAL(tid) \
+ ((((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) >> 29) + 11 - 1)
+#define QLOGIC_IB_RT_BUFSIZE(tid) (1 << QLOGIC_IB_RT_BUFSIZE_SHIFTVAL(tid))
+#define QLOGIC_IB_RT_IS_VALID(tid) \
+ (((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) && \
+ ((((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) != QLOGIC_IB_RT_BUFSIZE_MASK)))
+#define QLOGIC_IB_RT_ADDR_MASK 0x1FFFFFFFULL /* 29 bits valid */
+#define QLOGIC_IB_RT_ADDR_SHIFT 10
+
+#define QLOGIC_IB_R_INTRAVAIL_SHIFT 16
+#define QLOGIC_IB_R_TAILUPD_SHIFT 31
+#define IBA6120_R_PKEY_DIS_SHIFT 30
+
+#define PBC_6120_VL15_SEND_CTRL (1ULL << 31) /* pbc; VL15; link_buf only */
+
+#define IBCBUSFRSPCPARITYERR HWE_MASK(IBCBusFromSPCParityErr)
+#define IBCBUSTOSPCPARITYERR HWE_MASK(IBCBusToSPCParityErr)
+
+#define SYM_MASK_BIT(regname, fldname, bit) ((u64) \
+ ((1ULL << (SYM_LSB(regname, fldname) + (bit)))))
+
+#define TXEMEMPARITYERR_PIOBUF \
+ SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 0)
+#define TXEMEMPARITYERR_PIOPBC \
+ SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 1)
+#define TXEMEMPARITYERR_PIOLAUNCHFIFO \
+ SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 2)
+
+#define RXEMEMPARITYERR_RCVBUF \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 0)
+#define RXEMEMPARITYERR_LOOKUPQ \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 1)
+#define RXEMEMPARITYERR_EXPTID \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 2)
+#define RXEMEMPARITYERR_EAGERTID \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 3)
+#define RXEMEMPARITYERR_FLAGBUF \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 4)
+#define RXEMEMPARITYERR_DATAINFO \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 5)
+#define RXEMEMPARITYERR_HDRINFO \
+ SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 6)
+
+/* 6120 specific hardware errors... */
+static const struct qib_hwerror_msgs qib_6120_hwerror_msgs[] = {
+ /* generic hardware errors */
+ QLOGIC_IB_HWE_MSG(IBCBUSFRSPCPARITYERR, "QIB2IB Parity"),
+ QLOGIC_IB_HWE_MSG(IBCBUSTOSPCPARITYERR, "IB2QIB Parity"),
+
+ QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOBUF,
+ "TXE PIOBUF Memory Parity"),
+ QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOPBC,
+ "TXE PIOPBC Memory Parity"),
+ QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOLAUNCHFIFO,
+ "TXE PIOLAUNCHFIFO Memory Parity"),
+
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_RCVBUF,
+ "RXE RCVBUF Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_LOOKUPQ,
+ "RXE LOOKUPQ Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_EAGERTID,
+ "RXE EAGERTID Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_EXPTID,
+ "RXE EXPTID Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_FLAGBUF,
+ "RXE FLAGBUF Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_DATAINFO,
+ "RXE DATAINFO Memory Parity"),
+ QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_HDRINFO,
+ "RXE HDRINFO Memory Parity"),
+
+ /* chip-specific hardware errors */
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEPOISONEDTLP,
+ "PCIe Poisoned TLP"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIECPLTIMEOUT,
+ "PCIe completion timeout"),
+ /*
+ * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
+ * parity or memory parity error failures, because most likely we
+ * won't be able to talk to the core of the chip. Nonetheless, we
+ * might see them, if they are in parts of the PCIe core that aren't
+ * essential.
+ */
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIE1PLLFAILED,
+ "PCIePLL1"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIE0PLLFAILED,
+ "PCIePLL0"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYXTLH,
+ "PCIe XTLH core parity"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYXADM,
+ "PCIe ADM TX core parity"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYRADM,
+ "PCIe ADM RX core parity"),
+ QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_SERDESPLLFAILED,
+ "SerDes PLL"),
+};
+
+#define TXE_PIO_PARITY (TXEMEMPARITYERR_PIOBUF | TXEMEMPARITYERR_PIOPBC)
+#define _QIB_PLL_FAIL (QLOGIC_IB_HWE_COREPLL_FBSLIP | \
+ QLOGIC_IB_HWE_COREPLL_RFSLIP)
+
+ /* variables for sanity checking interrupt and errors */
+#define IB_HWE_BITSEXTANT \
+ (HWE_MASK(RXEMemParityErr) | \
+ HWE_MASK(TXEMemParityErr) | \
+ (QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK << \
+ QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT) | \
+ QLOGIC_IB_HWE_PCIE1PLLFAILED | \
+ QLOGIC_IB_HWE_PCIE0PLLFAILED | \
+ QLOGIC_IB_HWE_PCIEPOISONEDTLP | \
+ QLOGIC_IB_HWE_PCIECPLTIMEOUT | \
+ QLOGIC_IB_HWE_PCIEBUSPARITYXTLH | \
+ QLOGIC_IB_HWE_PCIEBUSPARITYXADM | \
+ QLOGIC_IB_HWE_PCIEBUSPARITYRADM | \
+ HWE_MASK(PowerOnBISTFailed) | \
+ QLOGIC_IB_HWE_COREPLL_FBSLIP | \
+ QLOGIC_IB_HWE_COREPLL_RFSLIP | \
+ QLOGIC_IB_HWE_SERDESPLLFAILED | \
+ HWE_MASK(IBCBusToSPCParityErr) | \
+ HWE_MASK(IBCBusFromSPCParityErr))
+
+#define IB_E_BITSEXTANT \
+ (ERR_MASK(RcvFormatErr) | ERR_MASK(RcvVCRCErr) | \
+ ERR_MASK(RcvICRCErr) | ERR_MASK(RcvMinPktLenErr) | \
+ ERR_MASK(RcvMaxPktLenErr) | ERR_MASK(RcvLongPktLenErr) | \
+ ERR_MASK(RcvShortPktLenErr) | ERR_MASK(RcvUnexpectedCharErr) | \
+ ERR_MASK(RcvUnsupportedVLErr) | ERR_MASK(RcvEBPErr) | \
+ ERR_MASK(RcvIBFlowErr) | ERR_MASK(RcvBadVersionErr) | \
+ ERR_MASK(RcvEgrFullErr) | ERR_MASK(RcvHdrFullErr) | \
+ ERR_MASK(RcvBadTidErr) | ERR_MASK(RcvHdrLenErr) | \
+ ERR_MASK(RcvHdrErr) | ERR_MASK(RcvIBLostLinkErr) | \
+ ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendMaxPktLenErr) | \
+ ERR_MASK(SendUnderRunErr) | ERR_MASK(SendPktLenErr) | \
+ ERR_MASK(SendDroppedSmpPktErr) | \
+ ERR_MASK(SendDroppedDataPktErr) | \
+ ERR_MASK(SendPioArmLaunchErr) | \
+ ERR_MASK(SendUnexpectedPktNumErr) | \
+ ERR_MASK(SendUnsupportedVLErr) | ERR_MASK(IBStatusChanged) | \
+ ERR_MASK(InvalidAddrErr) | ERR_MASK(ResetNegated) | \
+ ERR_MASK(HardwareErr))
+
+#define QLOGIC_IB_E_PKTERRS ( \
+ ERR_MASK(SendPktLenErr) | \
+ ERR_MASK(SendDroppedDataPktErr) | \
+ ERR_MASK(RcvVCRCErr) | \
+ ERR_MASK(RcvICRCErr) | \
+ ERR_MASK(RcvShortPktLenErr) | \
+ ERR_MASK(RcvEBPErr))
+
+/* These are all rcv-related errors which we want to count for stats */
+#define E_SUM_PKTERRS \
+ (ERR_MASK(RcvHdrLenErr) | ERR_MASK(RcvBadTidErr) | \
+ ERR_MASK(RcvBadVersionErr) | ERR_MASK(RcvHdrErr) | \
+ ERR_MASK(RcvLongPktLenErr) | ERR_MASK(RcvShortPktLenErr) | \
+ ERR_MASK(RcvMaxPktLenErr) | ERR_MASK(RcvMinPktLenErr) | \
+ ERR_MASK(RcvFormatErr) | ERR_MASK(RcvUnsupportedVLErr) | \
+ ERR_MASK(RcvUnexpectedCharErr) | ERR_MASK(RcvEBPErr))
+
+/* These are all send-related errors which we want to count for stats */
+#define E_SUM_ERRS \
+ (ERR_MASK(SendPioArmLaunchErr) | \
+ ERR_MASK(SendUnexpectedPktNumErr) | \
+ ERR_MASK(SendDroppedDataPktErr) | \
+ ERR_MASK(SendDroppedSmpPktErr) | \
+ ERR_MASK(SendMaxPktLenErr) | ERR_MASK(SendUnsupportedVLErr) | \
+ ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendPktLenErr) | \
+ ERR_MASK(InvalidAddrErr))
+
+/*
+ * this is similar to E_SUM_ERRS, but can't ignore armlaunch, don't ignore
+ * errors not related to freeze and cancelling buffers. Can't ignore
+ * armlaunch because could get more while still cleaning up, and need
+ * to cancel those as they happen.
+ */
+#define E_SPKT_ERRS_IGNORE \
+ (ERR_MASK(SendDroppedDataPktErr) | \
+ ERR_MASK(SendDroppedSmpPktErr) | \
+ ERR_MASK(SendMaxPktLenErr) | ERR_MASK(SendMinPktLenErr) | \
+ ERR_MASK(SendPktLenErr))
+
+/*
+ * these are errors that can occur when the link changes state while
+ * a packet is being sent or received. This doesn't cover things
+ * like EBP or VCRC that can be the result of a sending having the
+ * link change state, so we receive a "known bad" packet.
+ */
+#define E_SUM_LINK_PKTERRS \
+ (ERR_MASK(SendDroppedDataPktErr) | \
+ ERR_MASK(SendDroppedSmpPktErr) | \
+ ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendPktLenErr) | \
+ ERR_MASK(RcvShortPktLenErr) | ERR_MASK(RcvMinPktLenErr) | \
+ ERR_MASK(RcvUnexpectedCharErr))
+
+static void qib_6120_put_tid_2(struct qib_devdata *, u64 __iomem *,
+ u32, unsigned long);
+
+/*
+ * On platforms using this chip, and not having ordered WC stores, we
+ * can get TXE parity errors due to speculative reads to the PIO buffers,
+ * and this, due to a chip issue can result in (many) false parity error
+ * reports. So it's a debug print on those, and an info print on systems
+ * where the speculative reads don't occur.
+ */
+static void qib_6120_txe_recover(struct qib_devdata *dd)
+{
+ if (!qib_unordered_wc())
+ qib_devinfo(dd->pcidev,
+ "Recovering from TXE PIO parity error\n");
+}
+
+/* enable/disable chip from delivering interrupts */
+static void qib_6120_set_intr_state(struct qib_devdata *dd, u32 enable)
+{
+ if (enable) {
+ if (dd->flags & QIB_BADINTR)
+ return;
+ qib_write_kreg(dd, kr_intmask, ~0ULL);
+ /* force re-interrupt of any pending interrupts. */
+ qib_write_kreg(dd, kr_intclear, 0ULL);
+ } else
+ qib_write_kreg(dd, kr_intmask, 0ULL);
+}
+
+/*
+ * Try to cleanup as much as possible for anything that might have gone
+ * wrong while in freeze mode, such as pio buffers being written by user
+ * processes (causing armlaunch), send errors due to going into freeze mode,
+ * etc., and try to avoid causing extra interrupts while doing so.
+ * Forcibly update the in-memory pioavail register copies after cleanup
+ * because the chip won't do it while in freeze mode (the register values
+ * themselves are kept correct).
+ * Make sure that we don't lose any important interrupts by using the chip
+ * feature that says that writing 0 to a bit in *clear that is set in
+ * *status will cause an interrupt to be generated again (if allowed by
+ * the *mask value).
+ * This is in chip-specific code because of all of the register accesses,
+ * even though the details are similar on most chips
+ */
+static void qib_6120_clear_freeze(struct qib_devdata *dd)
+{
+ /* disable error interrupts, to avoid confusion */
+ qib_write_kreg(dd, kr_errmask, 0ULL);
+
+ /* also disable interrupts; errormask is sometimes overwriten */
+ qib_6120_set_intr_state(dd, 0);
+
+ qib_cancel_sends(dd->pport);
+
+ /* clear the freeze, and be sure chip saw it */
+ qib_write_kreg(dd, kr_control, dd->control);
+ qib_read_kreg32(dd, kr_scratch);
+
+ /* force in-memory update now we are out of freeze */
+ qib_force_pio_avail_update(dd);
+
+ /*
+ * force new interrupt if any hwerr, error or interrupt bits are
+ * still set, and clear "safe" send packet errors related to freeze
+ * and cancelling sends. Re-enable error interrupts before possible
+ * force of re-interrupt on pending interrupts.
+ */
+ qib_write_kreg(dd, kr_hwerrclear, 0ULL);
+ qib_write_kreg(dd, kr_errclear, E_SPKT_ERRS_IGNORE);
+ qib_write_kreg(dd, kr_errmask, dd->cspec->errormask);
+ qib_6120_set_intr_state(dd, 1);
+}
+
+/**
+ * qib_handle_6120_hwerrors - display hardware errors.
+ * @dd: the qlogic_ib device
+ * @msg: the output buffer
+ * @msgl: the size of the output buffer
+ *
+ * Use same msg buffer as regular errors to avoid excessive stack
+ * use. Most hardware errors are catastrophic, but for right now,
+ * we'll print them and continue. Reuse the same message buffer as
+ * handle_6120_errors() to avoid excessive stack usage.
+ */
+static void qib_handle_6120_hwerrors(struct qib_devdata *dd, char *msg,
+ size_t msgl)
+{
+ u64 hwerrs;
+ u32 bits, ctrl;
+ int isfatal = 0;
+ char *bitsmsg;
+ int log_idx;
+
+ hwerrs = qib_read_kreg64(dd, kr_hwerrstatus);
+ if (!hwerrs)
+ return;
+ if (hwerrs == ~0ULL) {
+ qib_dev_err(dd, "Read of hardware error status failed "
+ "(all bits set); ignoring\n");
+ return;
+ }
+ qib_stats.sps_hwerrs++;
+
+ /* Always clear the error status register, except MEMBISTFAIL,
+ * regardless of whether we continue or stop using the chip.
+ * We want that set so we know it failed, even across driver reload.
+ * We'll still ignore it in the hwerrmask. We do this partly for
+ * diagnostics, but also for support */
+ qib_write_kreg(dd, kr_hwerrclear,
+ hwerrs & ~HWE_MASK(PowerOnBISTFailed));
+
+ hwerrs &= dd->cspec->hwerrmask;
+
+ /* We log some errors to EEPROM, check if we have any of those. */
+ for (log_idx = 0; log_idx < QIB_EEP_LOG_CNT; ++log_idx)
+ if (hwerrs & dd->eep_st_masks[log_idx].hwerrs_to_log)
+ qib_inc_eeprom_err(dd, log_idx, 1);
+
+ /*
+ * Make sure we get this much out, unless told to be quiet,
+ * or it's occurred within the last 5 seconds.
+ */
+ if (hwerrs & ~(TXE_PIO_PARITY | RXEMEMPARITYERR_EAGERTID))
+ qib_devinfo(dd->pcidev, "Hardware error: hwerr=0x%llx "
+ "(cleared)\n", (unsigned long long) hwerrs);
+
+ if (hwerrs & ~IB_HWE_BITSEXTANT)
+ qib_dev_err(dd, "hwerror interrupt with unknown errors "
+ "%llx set\n", (unsigned long long)
+ (hwerrs & ~IB_HWE_BITSEXTANT));
+
+ ctrl = qib_read_kreg32(dd, kr_control);
+ if ((ctrl & QLOGIC_IB_C_FREEZEMODE) && !dd->diag_client) {
+ /*
+ * Parity errors in send memory are recoverable,
+ * just cancel the send (if indicated in * sendbuffererror),
+ * count the occurrence, unfreeze (if no other handled
+ * hardware error bits are set), and continue. They can
+ * occur if a processor speculative read is done to the PIO
+ * buffer while we are sending a packet, for example.
+ */
+ if (hwerrs & TXE_PIO_PARITY) {
+ qib_6120_txe_recover(dd);
+ hwerrs &= ~TXE_PIO_PARITY;
+ }
+
+ if (!hwerrs) {
+ static u32 freeze_cnt;
+
+ freeze_cnt++;
+ qib_6120_clear_freeze(dd);
+ } else
+ isfatal = 1;
+ }
+
+ *msg = '\0';
+
+ if (hwerrs & HWE_MASK(PowerOnBISTFailed)) {
+ isfatal = 1;
+ strlcat(msg, "[Memory BIST test failed, InfiniPath hardware"
+ " unusable]", msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ dd->cspec->hwerrmask &= ~HWE_MASK(PowerOnBISTFailed);
+ qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
+ }
+
+ qib_format_hwerrors(hwerrs, qib_6120_hwerror_msgs,
+ ARRAY_SIZE(qib_6120_hwerror_msgs), msg, msgl);
+
+ bitsmsg = dd->cspec->bitsmsgbuf;
+ if (hwerrs & (QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK <<
+ QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT)) {
+ bits = (u32) ((hwerrs >>
+ QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT) &
+ QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK);
+ snprintf(bitsmsg, sizeof dd->cspec->bitsmsgbuf,
+ "[PCIe Mem Parity Errs %x] ", bits);
+ strlcat(msg, bitsmsg, msgl);
+ }
+
+ if (hwerrs & _QIB_PLL_FAIL) {
+ isfatal = 1;
+ snprintf(bitsmsg, sizeof dd->cspec->bitsmsgbuf,
+ "[PLL failed (%llx), InfiniPath hardware unusable]",
+ (unsigned long long) hwerrs & _QIB_PLL_FAIL);
+ strlcat(msg, bitsmsg, msgl);
+ /* ignore from now on, so disable until driver reloaded */
+ dd->cspec->hwerrmask &= ~(hwerrs & _QIB_PLL_FAIL);
+ qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
+ }
+
+ if (hwerrs & QLOGIC_IB_HWE_SERDESPLLFAILED) {
+ /*
+ * If it occurs, it is left masked since the external
+ * interface is unused
+ */
+ dd->cspec->hwerrmask &= ~QLOGIC_IB_HWE_SERDESPLLFAILED;
+ qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
+ }
+
+ if (hwerrs)
+ /*
+ * if any set that we aren't ignoring; only
+ * make the complaint once, in case it's stuck
+ * or recurring, and we get here multiple
+ * times.
+ */
+ qib_dev_err(dd, "%s hardware error\n", msg);
+ else
+ *msg = 0; /* recovered from all of them */
+
+ if (isfatal && !dd->diag_client) {
+ qib_dev_err(dd, "Fatal Hardware Error, no longer"
+ " usable, SN %.16s\n", dd->serial);
+ /*
+ * for /sys status file and user programs to print; if no
+ * trailing brace is copied, we'll know it was truncated.
+ */
+ if (dd->freezemsg)
+ snprintf(dd->freezemsg, dd->freezelen,
+ "{%s}", msg);
+ qib_disable_after_error(dd);
+ }
+}
+
+/*
+ * Decode the error status into strings, deciding whether to always
+ * print * it or not depending on "normal packet errors" vs everything
+ * else. Return 1 if "real" errors, otherwise 0 if only packet
+ * errors, so caller can decide what to print with the string.
+ */
+static int qib_decode_6120_err(struct qib_devdata *dd, char *buf, size_t blen,
+ u64 err)
+{
+ int iserr = 1;
+
+ *buf = '\0';
+ if (err & QLOGIC_IB_E_PKTERRS) {
+ if (!(err & ~QLOGIC_IB_E_PKTERRS))
+ iserr = 0;
+ if ((err & ERR_MASK(RcvICRCErr)) &&
+ !(err&(ERR_MASK(RcvVCRCErr)|ERR_MASK(RcvEBPErr))))
+ strlcat(buf, "CRC ", blen);
+ if (!iserr)
+ goto done;
+ }
+ if (err & ERR_MASK(RcvHdrLenErr))
+ strlcat(buf, "rhdrlen ", blen);
+ if (err & ERR_MASK(RcvBadTidErr))
+ strlcat(buf, "rbadtid ", blen);
+ if (err & ERR_MASK(RcvBadVersionErr))
+ strlcat(buf, "rbadversion ", blen);
+ if (err & ERR_MASK(RcvHdrErr))
+ strlcat(buf, "rhdr ", blen);
+ if (err & ERR_MASK(RcvLongPktLenErr))
+ strlcat(buf, "rlongpktlen ", blen);
+ if (err & ERR_MASK(RcvMaxPktLenErr))
+ strlcat(buf, "rmaxpktlen ", blen);
+ if (err & ERR_MASK(RcvMinPktLenErr))
+ strlcat(buf, "rminpktlen ", blen);
+ if (err & ERR_MASK(SendMinPktLenErr))
+ strlcat(buf, "sminpktlen ", blen);
+ if (err & ERR_MASK(RcvFormatErr))
+ strlcat(buf, "rformaterr ", blen);
+ if (err & ERR_MASK(RcvUnsupportedVLErr))
+ strlcat(buf, "runsupvl ", blen);
+ if (err & ERR_MASK(RcvUnexpectedCharErr))
+ strlcat(buf, "runexpchar ", blen);
+ if (err & ERR_MASK(RcvIBFlowErr))
+ strlcat(buf, "ribflow ", blen);
+ if (err & ERR_MASK(SendUnderRunErr))
+ strlcat(buf, "sunderrun ", blen);
+ if (err & ERR_MASK(SendPioArmLaunchErr))
+ strlcat(buf, "spioarmlaunch ", blen);
+ if (err & ERR_MASK(SendUnexpectedPktNumErr))
+ strlcat(buf, "sunexperrpktnum ", blen);
+ if (err & ERR_MASK(SendDroppedSmpPktErr))
+ strlcat(buf, "sdroppedsmppkt ", blen);
+ if (err & ERR_MASK(SendMaxPktLenErr))
+ strlcat(buf, "smaxpktlen ", blen);
+ if (err & ERR_MASK(SendUnsupportedVLErr))
+ strlcat(buf, "sunsupVL ", blen);
+ if (err & ERR_MASK(InvalidAddrErr))
+ strlcat(buf, "invalidaddr ", blen);
+ if (err & ERR_MASK(RcvEgrFullErr))
+ strlcat(buf, "rcvegrfull ", blen);
+ if (err & ERR_MASK(RcvHdrFullErr))
+ strlcat(buf, "rcvhdrfull ", blen);
+ if (err & ERR_MASK(IBStatusChanged))
+ strlcat(buf, "ibcstatuschg ", blen);
+ if (err & ERR_MASK(RcvIBLostLinkErr))
+ strlcat(buf, "riblostlink ", blen);
+ if (err & ERR_MASK(HardwareErr))
+ strlcat(buf, "hardware ", blen);
+ if (err & ERR_MASK(ResetNegated))
+ strlcat(buf, "reset ", blen);
+done:
+ return iserr;
+}
+
+/*
+ * Called when we might have an error that is specific to a particular
+ * PIO buffer, and may need to cancel that buffer, so it can be re-used.
+ */
+static void qib_disarm_6120_senderrbufs(struct qib_pportdata *ppd)
+{
+ unsigned long sbuf[2];
+ struct qib_devdata *dd = ppd->dd;
+
+ /*
+ * It's possible that sendbuffererror could have bits set; might
+ * have already done this as a result of hardware error handling.
+ */
+ sbuf[0] = qib_read_kreg64(dd, kr_sendbuffererror);
+ sbuf[1] = qib_read_kreg64(dd, kr_sendbuffererror + 1);
+
+ if (sbuf[0] || sbuf[1])
+ qib_disarm_piobufs_set(dd, sbuf,
+ dd->piobcnt2k + dd->piobcnt4k);
+}
+
+static int chk_6120_linkrecovery(struct qib_devdata *dd, u64 ibcs)
+{
+ int ret = 1;
+ u32 ibstate = qib_6120_iblink_state(ibcs);
+ u32 linkrecov = read_6120_creg32(dd, cr_iblinkerrrecov);
+
+ if (linkrecov != dd->cspec->lastlinkrecov) {
+ /* and no more until active again */
+ dd->cspec->lastlinkrecov = 0;
+ qib_set_linkstate(dd->pport, QIB_IB_LINKDOWN);
+ ret = 0;
+ }
+ if (ibstate == IB_PORT_ACTIVE)
+ dd->cspec->lastlinkrecov =
+ read_6120_creg32(dd, cr_iblinkerrrecov);
+ return ret;
+}
+
+static void handle_6120_errors(struct qib_devdata *dd, u64 errs)
+{
+ char *msg;
+ u64 ignore_this_time = 0;
+ u64 iserr = 0;
+ int log_idx;
+ struct qib_pportdata *ppd = dd->pport;
+ u64 mask;
+
+ /* don't report errors that are masked */
+ errs &= dd->cspec->errormask;
+ msg = dd->cspec->emsgbuf;
+
+ /* do these first, they are most important */
+ if (errs & ERR_MASK(HardwareErr))
+ qib_handle_6120_hwerrors(dd, msg, sizeof dd->cspec->emsgbuf);
+ else
+ for (log_idx = 0; log_idx < QIB_EEP_LOG_CNT; ++log_idx)
+ if (errs & dd->eep_st_masks[log_idx].errs_to_log)
+ qib_inc_eeprom_err(dd, log_idx, 1);
+
+ if (errs & ~IB_E_BITSEXTANT)
+ qib_dev_err(dd, "error interrupt with unknown errors "
+ "%llx set\n",
+ (unsigned long long) (errs & ~IB_E_BITSEXTANT));
+
+ if (errs & E_SUM_ERRS) {
+ qib_disarm_6120_senderrbufs(ppd);
+ if ((errs & E_SUM_LINK_PKTERRS) &&
+ !(ppd->lflags & QIBL_LINKACTIVE)) {
+ /*
+ * This can happen when trying to bring the link
+ * up, but the IB link changes state at the "wrong"
+ * time. The IB logic then complains that the packet
+ * isn't valid. We don't want to confuse people, so
+ * we just don't print them, except at debug
+ */
+ ignore_this_time = errs & E_SUM_LINK_PKTERRS;
+ }
+ } else if ((errs & E_SUM_LINK_PKTERRS) &&
+ !(ppd->lflags & QIBL_LINKACTIVE)) {
+ /*
+ * This can happen when SMA is trying to bring the link
+ * up, but the IB link changes state at the "wrong" time.
+ * The IB logic then complains that the packet isn't
+ * valid. We don't want to confuse people, so we just
+ * don't print them, except at debug
+ */
+ ignore_this_time = errs & E_SUM_LINK_PKTERRS;
+ }
+
+ qib_write_kreg(dd, kr_errclear, errs);
+
+ errs &= ~ignore_this_time;
+ if (!errs)
+ goto done;
+
+ /*
+ * The ones we mask off are handled specially below
+ * or above.
+ */
+ mask = ERR_MASK(IBStatusChanged) | ERR_MASK(RcvEgrFullErr) |
+ ERR_MASK(RcvHdrFullErr) | ERR_MASK(HardwareErr);
+ qib_decode_6120_err(dd, msg, sizeof dd->cspec->emsgbuf, errs & ~mask);
+
+ if (errs & E_SUM_PKTERRS)
+ qib_stats.sps_rcverrs++;
+ if (errs & E_SUM_ERRS)
+ qib_stats.sps_txerrs++;
+
+ iserr = errs & ~(E_SUM_PKTERRS | QLOGIC_IB_E_PKTERRS);
+
+ if (errs & ERR_MASK(IBStatusChanged)) {
+ u64 ibcs = qib_read_kreg64(dd, kr_ibcstatus);
+ u32 ibstate = qib_6120_iblink_state(ibcs);
+ int handle = 1;
+
+ if (ibstate != IB_PORT_INIT && dd->cspec->lastlinkrecov)
+ handle = chk_6120_linkrecovery(dd, ibcs);
+ /*
+ * Since going into a recovery state causes the link state
+ * to go down and since recovery is transitory, it is better
+ * if we "miss" ever seeing the link training state go into
+ * recovery (i.e., ignore this transition for link state
+ * special handling purposes) without updating lastibcstat.
+ */
+ if (handle && qib_6120_phys_portstate(ibcs) ==
+ IB_PHYSPORTSTATE_LINK_ERR_RECOVER)
+ handle = 0;
+ if (handle)
+ qib_handle_e_ibstatuschanged(ppd, ibcs);
+ }
+
+ if (errs & ERR_MASK(ResetNegated)) {
+ qib_dev_err(dd, "Got reset, requires re-init "
+ "(unload and reload driver)\n");
+ dd->flags &= ~QIB_INITTED; /* needs re-init */
+ /* mark as having had error */
+ *dd->devstatusp |= QIB_STATUS_HWERROR;
+ *dd->pport->statusp &= ~QIB_STATUS_IB_CONF;
+ }
+
+ if (*msg && iserr)
+ qib_dev_porterr(dd, ppd->port, "%s error\n", msg);
+
+ if (ppd->state_wanted & ppd->lflags)
+ wake_up_interruptible(&ppd->state_wait);
+
+ /*
+ * If there were hdrq or egrfull errors, wake up any processes
+ * waiting in poll. We used to try to check which contexts had
+ * the overflow, but given the cost of that and the chip reads
+ * to support it, it's better to just wake everybody up if we
+ * get an overflow; waiters can poll again if it's not them.
+ */
+ if (errs & (ERR_MASK(RcvEgrFullErr) | ERR_MASK(RcvHdrFullErr))) {
+ qib_handle_urcv(dd, ~0U);
+ if (errs & ERR_MASK(RcvEgrFullErr))
+ qib_stats.sps_buffull++;
+ else
+ qib_stats.sps_hdrfull++;
+ }
+done:
+ return;
+}
+
+/**
+ * qib_6120_init_hwerrors - enable hardware errors
+ * @dd: the qlogic_ib device
+ *
+ * now that we have finished initializing everything that might reasonably
+ * cause a hardware error, and cleared those errors bits as they occur,
+ * we can enable hardware errors in the mask (potentially enabling
+ * freeze mode), and enable hardware errors as errors (along with
+ * everything else) in errormask
+ */
+static void qib_6120_init_hwerrors(struct qib_devdata *dd)
+{
+ u64 val;
+ u64 extsval;
+
+ extsval = qib_read_kreg64(dd, kr_extstatus);
+
+ if (!(extsval & QLOGIC_IB_EXTS_MEMBIST_ENDTEST))
+ qib_dev_err(dd, "MemBIST did not complete!\n");
+
+ /* init so all hwerrors interrupt, and enter freeze, ajdust below */
+ val = ~0ULL;
+ if (dd->minrev < 2) {
+ /*
+ * Avoid problem with internal interface bus parity
+ * checking. Fixed in Rev2.
+ */
+ val &= ~QLOGIC_IB_HWE_PCIEBUSPARITYRADM;
+ }
+ /* avoid some intel cpu's speculative read freeze mode issue */
+ val &= ~TXEMEMPARITYERR_PIOBUF;
+
+ dd->cspec->hwerrmask = val;
+
+ qib_write_kreg(dd, kr_hwerrclear, ~HWE_MASK(PowerOnBISTFailed));
+ qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
+
+ /* clear all */
+ qib_write_kreg(dd, kr_errclear, ~0ULL);
+ /* enable errors that are masked, at least this first time. */
+ qib_write_kreg(dd, kr_errmask, ~0ULL);
+ dd->cspec->errormask = qib_read_kreg64(dd, kr_errmask);
+ /* clear any interrupts up to this point (ints still not enabled) */
+ qib_write_kreg(dd, kr_intclear, ~0ULL);
+
+ qib_write_kreg(dd, kr_rcvbthqp,
+ dd->qpn_mask << (QIB_6120_RcvBTHQP_BTHQP_Mask_LSB - 1) |
+ QIB_KD_QP);
+}
+
+/*
+ * Disable and enable the armlaunch error. Used for PIO bandwidth testing
+ * on chips that are count-based, rather than trigger-based. There is no
+ * reference counting, but that's also fine, given the intended use.
+ * Only chip-specific because it's all register accesses
+ */
+static void qib_set_6120_armlaunch(struct qib_devdata *dd, u32 enable)
+{
+ if (enable) {
+ qib_write_kreg(dd, kr_errclear,
+ ERR_MASK(SendPioArmLaunchErr));
+ dd->cspec->errormask |= ERR_MASK(SendPioArmLaunchErr);
+ } else
+ dd->cspec->errormask &= ~ERR_MASK(SendPioArmLaunchErr);
+ qib_write_kreg(dd, kr_errmask, dd->cspec->errormask);
+}
+
+/*
+ * Formerly took parameter <which> in pre-shifted,
+ * pre-merged form with LinkCmd and LinkInitCmd
+ * together, and assuming the zero was NOP.
+ */
+static void qib_set_ib_6120_lstate(struct qib_pportdata *ppd, u16 linkcmd,
+ u16 linitcmd)
+{
+ u64 mod_wd;
+ struct qib_devdata *dd = ppd->dd;
+ unsigned long flags;
+
+ if (linitcmd == QLOGIC_IB_IBCC_LINKINITCMD_DISABLE) {
+ /*
+ * If we are told to disable, note that so link-recovery
+ * code does not attempt to bring us back up.
+ */
+ spin_lock_irqsave(&ppd->lflags_lock, flags);
+ ppd->lflags |= QIBL_IB_LINK_DISABLED;
+ spin_unlock_irqrestore(&ppd->lflags_lock, flags);
+ } else if (linitcmd || linkcmd == QLOGIC_IB_IBCC_LINKCMD_DOWN) {
+ /*
+ * Any other linkinitcmd will lead to LINKDOWN and then
+ * to INIT (if all is well), so clear flag to let
+ * link-recovery code attempt to bring us back up.
+ */
+ spin_lock_irqsave(&ppd->lflags_lock, flags);
+ ppd->lflags &= ~QIBL_IB_LINK_DISABLED;
+ spin_unlock_irqrestore(&ppd->lflags_lock, flags);
+ }
+
+ mod_wd = (linkcmd << QLOGIC_IB_IBCC_LINKCMD_SHIFT) |
+ (linitcmd << QLOGIC_IB_IBCC_LINKINITCMD_SHIFT);
+
+ qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl | mod_wd);
+ /* write to chip to prevent back-to-back writes of control reg */
+ qib_write_kreg(dd, kr_scratch, 0);
+}
+
+/**
+ * qib_6120_bringup_serdes - bring up the serdes
+ * @dd: the qlogic_ib device
+ */
+static int qib_6120_bringup_serdes(struct qib_pportdata *ppd)
+{
+ struct qib_devdata *dd = ppd->dd;
+ u64 val, config1, prev_val, hwstat, ibc;
+
+ /* Put IBC in reset, sends disabled */
+ dd->control &= ~QLOGIC_IB_C_LINKENABLE;
+ qib_write_kreg(dd, kr_control, 0ULL);
+
+ dd->cspec->ibdeltainprog = 1;
+ dd->cspec->ibsymsnap = read_6120_creg32(dd, cr_ibsymbolerr);
+ dd->cspec->iblnkerrsnap = read_6120_creg32(dd, cr_iblinkerrrecov);
+
+ /* flowcontrolwatermark is in units of KBytes */
+ ibc = 0x5ULL << SYM_LSB(IBCCtrl, FlowCtrlWaterMark);
+ /*
+ * How often flowctrl sent. More or less in usecs; balance against
+ * watermark value, so that in theory senders always get a flow
+ * control update in time to not let the IB link go idle.
+ */
+ ibc |= 0x3ULL << SYM_LSB(IBCCtrl, FlowCtrlPeriod);
+ /* max error tolerance */
+ dd->cspec->lli_thresh = 0xf;
+ ibc |= (u64) dd->cspec->lli_thresh << SYM_LSB(IBCCtrl, PhyerrThreshold);
+ /* use "real" buffer space for */
+ ibc |= 4ULL << SYM_LSB(IBCCtrl, CreditScale);
+ /* IB credit flow control. */
+ ibc |= 0xfULL << SYM_LSB(IBCCtrl, OverrunThreshold);
+ /*
+ * set initial max size pkt IBC will send, including ICRC; it's the
+ * PIO buffer size in dwords, less 1; also see qib_set_mtu()
+ */
+ ibc |= ((u64)(ppd->ibmaxlen >> 2) + 1) << SYM_LSB(IBCCtrl, MaxPktLen);
+ dd->cspec->ibcctrl = ibc; /* without linkcmd or linkinitcmd! */
+
+ /* initially come up waiting for TS1, without sending anything. */
+ val = dd->cspec->ibcctrl | (QLOGIC_IB_IBCC_LINKINITCMD_DISABLE <<
+ QLOGIC_IB_IBCC_LINKINITCMD_SHIFT);
+ qib_write_kreg(dd, kr_ibcctrl, val);
+
+ val = qib_read_kreg64(dd, kr_serdes_cfg0);
+ config1 = qib_read_kreg64(dd, kr_serdes_cfg1);
+
+ /*
+ * Force reset on, also set rxdetect enable. Must do before reading
+ * serdesstatus at least for simulation, or some of the bits in
+ * serdes status will come back as undefined and cause simulation
+ * failures
+ */
+ val |= SYM_MASK(SerdesCfg0, ResetPLL) |
+ SYM_MASK(SerdesCfg0, RxDetEnX) |
+ (SYM_MASK(SerdesCfg0, L1PwrDnA) |
+ SYM_MASK(SerdesCfg0, L1PwrDnB) |
+ SYM_MASK(SerdesCfg0, L1PwrDnC) |
+ SYM_MASK(SerdesCfg0, L1PwrDnD));
+ qib_write_kreg(dd, kr_serdes_cfg0, val);
+ /* be sure chip saw it */
+ qib_read_kreg64(dd, kr_scratch);
+ udelay(5); /* need pll reset set at least for a bit */
+ /*
+ * after PLL is reset, set the per-lane Resets and TxIdle and
+ * clear the PLL reset and rxdetect (to get falling edge).
+ * Leave L1PWR bits set (permanently)
+ */
+ val &= ~(SYM_MASK(SerdesCfg0, RxDetEnX) |
+ SYM_MASK(SerdesCfg0, ResetPLL) |
+ (SYM_MASK(SerdesCfg0, L1PwrDnA) |
+ SYM_MASK(SerdesCfg0, L1PwrDnB) |
+ SYM_MASK(SerdesCfg0, L1PwrDnC) |
+ SYM_MASK(SerdesCfg0, L1PwrDnD)));
+ val |= (SYM_MASK(SerdesCfg0, ResetA) |
+ SYM_MASK(SerdesCfg0, ResetB) |
+ SYM_MASK(SerdesCfg0, ResetC) |
+ SYM_MASK(SerdesCfg0, ResetD)) |
+ SYM_MASK(SerdesCfg0, TxIdeEnX);
+ qib_write_kreg(dd, kr_serdes_cfg0, val);
+ /* be sure chip saw it */
+ (void) qib_read_kreg64(dd, kr_scratch);
+ /* need PLL reset clear for at least 11 usec before lane
+ * resets cleared; give it a few more to be sure */
+ udelay(15);
+ val &= ~((SYM_MASK(SerdesCfg0, ResetA) |
+ SYM_MASK(SerdesCfg0, ResetB) |
+ SYM_MASK(SerdesCfg0, ResetC) |
+ SYM_MASK(SerdesCfg0, ResetD)) |
+ SYM_MASK(SerdesCfg0, TxIdeEnX));
+
+ qib_write_kreg(dd, kr_serdes_cfg0, val);
+ /* be sure chip saw it */
+ (void) qib_read_kreg64(dd, kr_scratch);
+
+ val = qib_read_kreg64(dd, kr_xgxs_cfg);
+ prev_val = val;
+ if (val & QLOGIC_IB_XGXS_RESET)
+ val &= ~QLOGIC_IB_XGXS_RESET;
+ if (SYM_FIELD(val, XGXSCfg, polarity_inv) != ppd->rx_pol_inv) {
+ /* need to compensate for Tx inversion in partner */
+ val &= ~SYM_MASK(XGXSCfg, polarity_inv);
+ val |= (u64)ppd->rx_pol_inv << SYM_LSB(XGXSCfg, polarity_inv);
+ }
+ if (val != prev_val)
+ qib_write_kreg(dd, kr_xgxs_cfg, val);
+
+ val = qib_read_kreg64(dd, kr_serdes_cfg0);
+
+ /* clear current and de-emphasis bits */
+ config1 &= ~0x0ffffffff00ULL;
+ /* set current to 20ma */
+ config1 |= 0x00000000000ULL;
+ /* set de-emphasis to -5.68dB */
+ config1 |= 0x0cccc000000ULL;
+ qib_write_kreg(dd, kr_serdes_cfg1, config1);
+
+ /* base and port guid same for single port */
+ ppd->guid = dd->base_guid;
+
+ /*
+ * the process of setting and un-resetting the serdes normally
+ * causes a serdes PLL error, so check for that and clear it
+ * here. Also clearr hwerr bit in errstatus, but not others.
+ */
+ hwstat = qib_read_kreg64(dd, kr_hwerrstatus);
+ if (hwstat) {
+ /* should just have PLL, clear all set, in an case */
+ if (hwstat & ~QLOGIC_IB_HWE_SERDESPLLFAILED)
+ qib_write_kreg(dd, kr_hwerrclear, hwstat);
+ qib_write_kreg(dd, kr_errclear, ERR_MASK(HardwareErr));
+ }
+
+ dd->control |= QLOGIC_IB_C_LINKENABLE;
+ dd->control &= ~QLOGIC_IB_C_FREEZEMODE;
+ qib_write_kreg(dd, kr_control, dd->control);
+
+ return 0;
+}
+
+/**
+ * qib_6120_quiet_serdes - set serdes to txidle
+ * @ppd: physical port of the qlogic_ib device
+ * Called when driver is being unloaded
+ */
+static void qib_6120_quiet_serdes(struct qib_pportdata *ppd)
+{
+ struct qib_devdata *dd = ppd->dd;
+ u64 val;
+
+ qib_set_ib_6120_lstate(ppd, 0, QLOGIC_IB_IBCC_LINKINITCMD_DISABLE);
+
+ /* disable IBC */
+ dd->control &= ~QLOGIC_IB_C_LINKENABLE;
+ qib_write_kreg(dd, kr_control,
+ dd->control | QLOGIC_IB_C_FREEZEMODE);
+
+ if (dd->cspec->ibsymdelta || dd->cspec->iblnkerrdelta ||
+ dd->cspec->ibdeltainprog) {
+ u64 diagc;
+
+ /* enable counter writes */
+ diagc = qib_read_kreg64(dd, kr_hwdiagctrl);
+ qib_write_kreg(dd, kr_hwdiagctrl,
+ diagc | SYM_MASK(HwDiagCtrl, CounterWrEnable));
+
+ if (dd->cspec->ibsymdelta || dd->cspec->ibdeltainprog) {
+ val = read_6120_creg32(dd, cr_ibsymbolerr);
+ if (dd->cspec->ibdeltainprog)
+ val -= val - dd->cspec->ibsymsnap;
+ val -= dd->cspec->ibsymdelta;
+ write_6120_creg(dd, cr_ibsymbolerr, val);
+ }
+ if (dd->cspec->iblnkerrdelta || dd->cspec->ibdeltainprog) {
+ val = read_6120_creg32(dd, cr_iblinkerrrecov);
+ if (dd->cspec->ibdeltainprog)
+ val -= val - dd->cspec->iblnkerrsnap;
+ val -= dd->cspec->iblnkerrdelta;
+ write_6120_creg(dd, cr_iblinkerrrecov, val);
+ }
+
+ /* and disable counter writes */
+ qib_write_kreg(dd, kr_hwdiagctrl, diagc);
+ }
+
+ val = qib_read_kreg64(dd, kr_serdes_cfg0);
+ val |= SYM_MASK(SerdesCfg0, TxIdeEnX);
+ qib_write_kreg(dd, kr_serdes_cfg0, val);
+}
+
+/**
+ * qib_6120_setup_setextled - set the state of the two external LEDs
+ * @dd: the qlogic_ib device
+ * @on: whether the link is up or not
+ *
+ * The exact combo of LEDs if on is true is determined by looking
+ * at the ibcstatus.
+
+ * These LEDs indicate the physical and logical state of IB link.
+ * For this chip (at least with recommended board pinouts), LED1
+ * is Yellow (logical state) and LED2 is Green (physical state),
+ *
+ * Note: We try to match the Mellanox HCA LED behavior as best
+ * we can. Green indicates physical link state is OK (something is
+ * plugged in, and we can train).
+ * Amber indicates the link is logically up (ACTIVE).
+ * Mellanox further blinks the amber LED to indicate data packet
+ * activity, but we have no hardware support for that, so it would
+ * require waking up every 10-20 msecs and checking the counters
+ * on the chip, and then turning the LED off if appropriate. That's
+ * visible overhead, so not something we will do.
+ *
+ */
+static void qib_6120_setup_setextled(struct qib_pportdata *ppd, u32 on)
+{
+ u64 extctl, val, lst, ltst;
+ unsigned long flags;
+ struct qib_devdata *dd = ppd->dd;
+
+ /*
+ * The diags use the LED to indicate diag info, so we leave
+ * the external LED alone when the diags are running.
+ */
+ if (dd->diag_client)
+ return;
+
+ /* Allow override of LED display for, e.g. Locating system in rack */
+ if (ppd->led_override) {
+ ltst = (ppd->led_override & QIB_LED_PHYS) ?
+ IB_PHYSPORTSTATE_LINKUP : IB_PHYSPORTSTATE_DISABLED,
+ lst = (ppd->led_override & QIB_LED_LOG) ?
+ IB_PORT_ACTIVE : IB_PORT_DOWN;
+ } else if (on) {
+ val = qib_read_kreg64(dd, kr_ibcstatus);
+ ltst = qib_6120_phys_portstate(val);
+ lst = qib_6120_iblink_state(val);
+ } else {
+ ltst = 0;
+ lst = 0;
+ }
+
+ spin_lock_irqsave(&dd->cspec->gpio_lock, flags);
+ extctl = dd->cspec->extctrl & ~(SYM_MASK(EXTCtrl, LEDPriPortGreenOn) |
+ SYM_MASK(EXTCtrl, LEDPriPortYellowOn));
+
+ if (ltst == IB_PHYSPORTSTATE_LINKUP)
+ extctl |= SYM_MASK(EXTCtrl, LEDPriPortYellowOn);
+ if (lst == IB_PORT_ACTIVE)
+ extctl |= SYM_MASK(EXTCtrl, LEDPriPortGreenOn);
+ dd->cspec->extctrl = extctl;
+ qib_write_kreg(dd, kr_extctrl, extctl);
+ spin_unlock_irqrestore(&dd->cspec->gpio_lock, flags);
+}
+
+static void qib_6120_free_irq(struct qib_devdata *dd)
+{
+ if (dd->cspec->irq) {
+ free_irq(dd->cspec->irq, dd);
+ dd->cspec->irq = 0;
+ }
+ qib_nomsi(dd);
+}
+
+/**
+ * qib_6120_setup_cleanup - clean up any per-chip chip-specific stuff
+ * @dd: the qlogic_ib device
+ *
+ * This is called during driver unload.
+*/
+static void qib_6120_setup_cleanup(struct qib_devdata *dd)
+{
+ qib_6120_free_irq(dd);
+ kfree(dd->cspec->cntrs);
+ kfree(dd->cspec->portcntrs);
+ if (dd->cspec->dummy_hdrq) {
+ dma_free_coherent(&dd->pcidev->dev,
+ ALIGN(dd->rcvhdrcnt *
+ dd->rcvhdrentsize *
+ sizeof(u32), PAGE_SIZE),
+ dd->cspec->dummy_hdrq,
+ dd->cspec->dummy_hdrq_phys);
+ dd->cspec->dummy_hdrq = NULL;
+ }
+}
+
+static void qib_wantpiobuf_6120_intr(struct qib_devdata *dd, u32 needint)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->sendctrl_lock, flags);
+ if (needint)
+ dd->sendctrl |= SYM_MASK(SendCtrl, PIOIntBufAvail);
+ else
+ dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOIntBufAvail);
+ qib_write_kreg(dd, kr_sendctrl, dd->sendctrl);
+ qib_write_kreg(dd, kr_scratch, 0ULL);
+ spin_unlock_irqrestore(&dd->sendctrl_lock, flags);
+}
+
+/*
+ * handle errors and unusual events first, separate function
+ * to improve cache hits for fast path interrupt handling
+ */
+static noinline void unlikely_6120_intr(struct qib_devdata *dd, u64 istat)
+{
+ if (unlikely(istat & ~QLOGIC_IB_I_BITSEXTANT))
+ qib_dev_err(dd, "interrupt with unknown interrupts %Lx set\n",
+ istat & ~QLOGIC_IB_I_BITSEXTANT);
+
+ if (istat & QLOGIC_IB_I_ERROR) {
+ u64 estat = 0;
+
+ qib_stats.sps_errints++;
+ estat = qib_read_kreg64(dd, kr_errstatus);
+ if (!estat)
+ qib_devinfo(dd->pcidev, "error interrupt (%Lx), "
+ "but no error bits set!\n", istat);
+ handle_6120_errors(dd, estat);
+ }
+
+ if (istat & QLOGIC_IB_I_GPIO) {
+ u32 gpiostatus;
+ u32 to_clear = 0;
+
+ /*
+ * GPIO_3..5 on IBA6120 Rev2 chips indicate
+ * errors that we need to count.
+ */
+ gpiostatus = qib_read_kreg32(dd, kr_gpio_status);
+ /* First the error-counter case. */
+ if (gpiostatus & GPIO_ERRINTR_MASK) {
+ /* want to clear the bits we see asserted. */
+ to_clear |= (gpiostatus & GPIO_ERRINTR_MASK);
+
+ /*
+ * Count appropriately, clear bits out of our copy,
+ * as they have been "handled".
+ */
+ if (gpiostatus & (1 << GPIO_RXUVL_BIT))
+ dd->cspec->rxfc_unsupvl_errs++;
+ if (gpiostatus & (1 << GPIO_OVRUN_BIT))
+ dd->cspec->overrun_thresh_errs++;
+ if (gpiostatus & (1 << GPIO_LLI_BIT))
+ dd->cspec->lli_errs++;
+ gpiostatus &= ~GPIO_ERRINTR_MASK;
+ }
+ if (gpiostatus) {
+ /*
+ * Some unexpected bits remain. If they could have
+ * caused the interrupt, complain and clear.
+ * To avoid repetition of this condition, also clear
+ * the mask. It is almost certainly due to error.
+ */
+ const u32 mask = qib_read_kreg32(dd, kr_gpio_mask);
+
+ /*
+ * Also check that the chip reflects our shadow,
+ * and report issues, If they caused the interrupt.
+ * we will suppress by refreshing from the shadow.
+ */
+ if (mask & gpiostatus) {
+ to_clear |= (gpiostatus & mask);
+ dd->cspec->gpio_mask &= ~(gpiostatus & mask);
+ qib_write_kreg(dd, kr_gpio_mask,
+ dd->cspec->gpio_mask);
+ }
+ }
+ if (to_clear)
+ qib_write_kreg(dd, kr_gpio_clear, (u64) to_clear);
+ }
+}
+
+static irqreturn_t qib_6120intr(int irq, void *data)
+{
+ struct qib_devdata *dd = data;
+ irqreturn_t ret;
+ u32 istat, ctxtrbits, rmask, crcs = 0;
+ unsigned i;
+
+ if ((dd->flags & (QIB_PRESENT | QIB_BADINTR)) != QIB_PRESENT) {
+ /*
+ * This return value is not great, but we do not want the
+ * interrupt core code to remove our interrupt handler
+ * because we don't appear to be handling an interrupt
+ * during a chip reset.
+ */
+ ret = IRQ_HANDLED;
+ goto bail;
+ }
+
+ istat = qib_read_kreg32(dd, kr_intstatus);
+
+ if (unlikely(!istat)) {
+ ret = IRQ_NONE; /* not our interrupt, or already handled */
+ goto bail;
+ }
+ if (unlikely(istat == -1)) {
+ qib_bad_intrstatus(dd);
+ /* don't know if it was our interrupt or not */
+ ret = IRQ_NONE;
+ goto bail;
+ }
+
+ qib_stats.sps_ints++;
+ if (dd->int_counter != (u32) -1)
+ dd->int_counter++;
+
+ if (unlikely(istat & (~QLOGIC_IB_I_BITSEXTANT |
+ QLOGIC_IB_I_GPIO | QLOGIC_IB_I_ERROR)))
+ unlikely_6120_intr(dd, istat);
+
+ /*
+ * Clear the interrupt bits we found set, relatively early, so we
+ * "know" know the chip will have seen this by the time we process
+ * the queue, and will re-interrupt if necessary. The processor
+ * itself won't take the interrupt again until we return.
+ */
+ qib_write_kreg(dd, kr_intclear, istat);
+
+ /*
+ * Handle kernel receive queues before checking for pio buffers
+ * available since receives can overflow; piobuf waiters can afford
+ * a few extra cycles, since they were waiting anyway.
+ */
+ ctxtrbits = istat &
+ ((QLOGIC_IB_I_RCVAVAIL_MASK << QLOGIC_IB_I_RCVAVAIL_SHIFT) |
+ (QLOGIC_IB_I_RCVURG_MASK << QLOGIC_IB_I_RCVURG_SHIFT));
+ if (ctxtrbits) {
+ rmask = (1U << QLOGIC_IB_I_RCVAVAIL_SHIFT) |
+ (1U << QLOGIC_IB_I_RCVURG_SHIFT);
+ for (i = 0; i < dd->first_user_ctxt; i++) {
+ if (ctxtrbits & rmask) {
+ ctxtrbits &= ~rmask;
+ crcs += qib_kreceive(dd->rcd[i],
+ &dd->cspec->lli_counter,
+ NULL);
+ }
+ rmask <<= 1;
+ }
+ if (crcs) {
+ u32 cntr = dd->cspec->lli_counter;
+ cntr += crcs;
+ if (cntr) {
+ if (cntr > dd->cspec->lli_thresh) {
+ dd->cspec->lli_counter = 0;
+ dd->cspec->lli_errs++;
+ } else
+ dd->cspec->lli_counter += cntr;
+ }
+ }
+
+
+ if (ctxtrbits) {
+ ctxtrbits =
+ (ctxtrbits >> QLOGIC_IB_I_RCVAVAIL_SHIFT) |
+ (ctxtrbits >> QLOGIC_IB_I_RCVURG_SHIFT);
+ qib_handle_urcv(dd, ctxtrbits);
+ }
+ }
+
+ if ((istat & QLOGIC_IB_I_SPIOBUFAVAIL) && (dd->flags & QIB_INITTED))
+ qib_ib_piobufavail(dd);
+
+ ret = IRQ_HANDLED;
+bail:
+ return ret;
+}
+
+/*
+ * Set up our chip-specific interrupt handler
+ * The interrupt type has already been setup, so
+ * we just need to do the registration and error checking.
+ */
+static void qib_setup_6120_interrupt(struct qib_devdata *dd)
+{
+ /*
+ * If the chip supports added error indication via GPIO pins,
+ * enable interrupts on those bits so the interrupt routine
+ * can count the events. Also set flag so interrupt routine
+ * can know they are expected.
+ */
+ if (SYM_FIELD(dd->revision, Revision_R,
+ ChipRevMinor) > 1) {
+ /* Rev2+ reports extra errors via internal GPIO pins */
+ dd->cspec->gpio_mask |= GPIO_ERRINTR_MASK;
+ qib_write_kreg(dd, kr_gpio_mask, dd->cspec->gpio_mask);
+ }
+
+ if (!dd->cspec->irq)
+ qib_dev_err(dd, "irq is 0, BIOS error? Interrupts won't "
+ "work\n");
+ else {
+ int ret;
+ ret = request_irq(dd->cspec->irq, qib_6120intr, 0,
+ QIB_DRV_NAME, dd);
+ if (ret)
+ qib_dev_err(dd, "Couldn't setup interrupt "
+ "(irq=%d): %d\n", dd->cspec->irq,
+ ret);
+ }
+}
+
+/**
+ * pe_boardname - fill in the board name
+ * @dd: the qlogic_ib device
+ *
+ * info is based on the board revision register
+ */
+static void pe_boardname(struct qib_devdata *dd)
+{
+ char *n;
+ u32 boardid, namelen;
+
+ boardid = SYM_FIELD(dd->revision, Revision,
+ BoardID);
+
+ switch (boardid) {
+ case 2:
+ n = "InfiniPath_QLE7140";
+ break;
+ default:
+ qib_dev_err(dd, "Unknown 6120 board with ID %u\n", boardid);
+ n = "Unknown_InfiniPath_6120";
+ break;
+ }
+ namelen = strlen(n) + 1;
+ dd->boardname = kmalloc(namelen, GFP_KERNEL);
+ if (!dd->boardname)
+ qib_dev_err(dd, "Failed allocation for board name: %s\n", n);
+ else
+ snprintf(dd->boardname, namelen, "%s", n);
+
+ if (dd->majrev != 4 || !dd->minrev || dd->minrev > 2)
+ qib_dev_err(dd, "Unsupported InfiniPath hardware revision "
+ "%u.%u!\n", dd->majrev, dd->minrev);
+
+ snprintf(dd->boardversion, sizeof(dd->boardversion),
+ "ChipABI %u.%u, %s, InfiniPath%u %u.%u, SW Compat %u\n",
+ QIB_CHIP_VERS_MAJ, QIB_CHIP_VERS_MIN, dd->boardname,
+ (unsigned)SYM_FIELD(dd->revision, Revision_R, Arch),
+ dd->majrev, dd->minrev,
+ (unsigned)SYM_FIELD(dd->revision, Revision_R, SW));
+
+}
+
+/*
+ * This routine sleeps, so it can only be called from user context, not
+ * from interrupt context. If we need interrupt context, we can split
+ * it into two routines.
+ */
+static int qib_6120_setup_reset(struct qib_devdata *dd)
+{
+ u64 val;
+ int i;
+ int ret;
+ u16 cmdval;
+ u8 int_line, clinesz;
+
+ qib_pcie_getcmd(dd, &cmdval, &int_line, &clinesz);
+
+ /* Use ERROR so it shows up in logs, etc. */
+ qib_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->unit);
+
+ /* no interrupts till re-initted */
+ qib_6120_set_intr_state(dd, 0);
+
+ dd->cspec->ibdeltainprog = 0;
+ dd->cspec->ibsymdelta = 0;
+ dd->cspec->iblnkerrdelta = 0;
+
+ /*
+ * Keep chip from being accessed until we are ready. Use
+ * writeq() directly, to allow the write even though QIB_PRESENT
+ * isnt' set.
+ */
+ dd->flags &= ~(QIB_INITTED | QIB_PRESENT);
+ dd->int_counter = 0; /* so we check interrupts work again */
+ val = dd->control | QLOGIC_IB_C_RESET;
+ writeq(val, &dd->kregbase[kr_control]);
+ mb(); /* prevent compiler re-ordering around actual reset */
+
+ for (i = 1; i <= 5; i++) {
+ /*
+ * Allow MBIST, etc. to complete; longer on each retry.
+ * We sometimes get machine checks from bus timeout if no
+ * response, so for now, make it *really* long.
+ */
+ msleep(1000 + (1 + i) * 2000);
+
+ qib_pcie_reenable(dd, cmdval, int_line, clinesz);
+
+ /*
+ * Use readq directly, so we don't need to mark it as PRESENT
+ * until we get a successful indication that all is well.
+ */
+ val = readq(&dd->kregbase[kr_revision]);
+ if (val == dd->revision) {
+ dd->flags |= QIB_PRESENT; /* it's back */
+ ret = qib_reinit_intr(dd);
+ goto bail;
+ }
+ }
+ ret = 0; /* failed */
+
+bail:
+ if (ret) {
+ if (qib_pcie_params(dd, dd->lbus_width, NULL, NULL))
+ qib_dev_err(dd, "Reset failed to setup PCIe or "
+ "interrupts; continuing anyway\n");
+ /* clear the reset error, init error/hwerror mask */
+ qib_6120_init_hwerrors(dd);
+ /* for Rev2 error interrupts; nop for rev 1 */
+ qib_write_kreg(dd, kr_gpio_mask, dd->cspec->gpio_mask);
+ /* clear the reset error, init error/hwerror mask */
+ qib_6120_init_hwerrors(dd);
+ }
+ return ret;
+}
+
+/**
+ * qib_6120_put_tid - write a TID in chip
+ * @dd: the qlogic_ib device
+ * @tidptr: pointer to the expected TID (in chip) to update
+ * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0)
+ * for expected
+ * @pa: physical address of in memory buffer; tidinvalid if freeing
+ *
+ * This exists as a separate routine to allow for special locking etc.
+ * It's used for both the full cleanup on exit, as well as the normal
+ * setup and teardown.
+ */
+static void qib_6120_put_tid(struct qib_devdata *dd, u64 __iomem *tidptr,
+ u32 type, unsigned long pa)
+{
+ u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
+ unsigned long flags;
+ int tidx;
+ spinlock_t *tidlockp; /* select appropriate spinlock */
+
+ if (!dd->kregbase)
+ return;
+
+ if (pa != dd->tidinvalid) {
+ if (pa & ((1U << 11) - 1)) {
+ qib_dev_err(dd, "Physaddr %lx not 2KB aligned!\n",
+ pa);
+ return;
+ }
+ pa >>= 11;
+ if (pa & ~QLOGIC_IB_RT_ADDR_MASK) {
+ qib_dev_err(dd, "Physical page address 0x%lx "
+ "larger than supported\n", pa);
+ return;
+ }
+
+ if (type == RCVHQ_RCV_TYPE_EAGER)
+ pa |= dd->tidtemplate;
+ else /* for now, always full 4KB page */
+ pa |= 2 << 29;
+ }
+
+ /*
+ * Avoid chip issue by writing the scratch register
+ * before and after the TID, and with an io write barrier.
+ * We use a spinlock around the writes, so they can't intermix
+ * with other TID (eager or expected) writes (the chip problem
+ * is triggered by back to back TID writes). Unfortunately, this
+ * call can be done from interrupt level for the ctxt 0 eager TIDs,
+ * so we have to use irqsave locks.
+ */
+ /*
+ * Assumes tidptr always > egrtidbase
+ * if type == RCVHQ_RCV_TYPE_EAGER.
+ */
+ tidx = tidptr - dd->egrtidbase;
+
+ tidlockp = (type == RCVHQ_RCV_TYPE_EAGER && tidx < dd->rcvhdrcnt)
+ ? &dd->cspec->kernel_tid_lock : &dd->cspec->user_tid_lock;
+ spin_lock_irqsave(tidlockp, flags);
+ qib_write_kreg(dd, kr_scratch, 0xfeeddeaf);
+ writel(pa, tidp32);
+ qib_write_kreg(dd, kr_scratch, 0xdeadbeef);
+ mmiowb();
+ spin_unlock_irqrestore(tidlockp, flags);
+}
+
+/**
+ * qib_6120_put_tid_2 - write a TID in chip, Revision 2 or higher
+ * @dd: the qlogic_ib device
+ * @tidptr: pointer to the expected TID (in chip) to update
+ * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0)
+ * for expected
+ * @pa: physical address of in memory buffer; tidinvalid if freeing
+ *
+ * This exists as a separate routine to allow for selection of the
+ * appropriate "flavor". The static calls in cleanup just use the
+ * revision-agnostic form, as they are not performance critical.
+ */
+static void qib_6120_put_tid_2(struct qib_devdata *dd, u64 __iomem *tidptr,
+ u32 type, unsigned long pa)
+{
+ u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
+ u32 tidx;
+
+ if (!dd->kregbase)
+ return;
+
+ if (pa != dd->tidinvalid) {
+ if (pa & ((1U << 11) - 1)) {
+ qib_dev_err(dd, "Physaddr %lx not 2KB aligned!\n",
+ pa);
+ return;
+ }
+ pa >>= 11;
+ if (pa & ~QLOGIC_IB_RT_ADDR_MASK) {
+ qib_dev_err(dd, "Physical page address 0x%lx "
+ "larger than supported\n", pa);
+ return;
+ }
+
+ if (type == RCVHQ_RCV_TYPE_EAGER)
+ pa |= dd->tidtemplate;
+ else /* for now, always full 4KB page */
+ pa |= 2 << 29;
+ }
+ tidx = tidptr - dd->egrtidbase;
+ writel(pa, tidp32);
+ mmiowb();
+}
+
+
+/**
+ * qib_6120_clear_tids - clear all TID entries for a context, expected and eager
+ * @dd: the qlogic_ib device
+ * @ctxt: the context
+ *
+ * clear all TID entries for a context, expected and eager.
+ * Used from qib_close(). On this chip, TIDs are only 32 bits,
+ * not 64, but they are still on 64 bit boundaries, so tidbase
+ * is declared as u64 * for the pointer math, even though we write 32 bits
+ */
+static void qib_6120_clear_tids(struct qib_devdata *dd,
+ struct qib_ctxtdata *rcd)
+{
+ u64 __iomem *tidbase;
+ unsigned long tidinv;
+ u32 ctxt;
+ int i;
+
+ if (!dd->kregbase || !rcd)
+ return;
+
+ ctxt = rcd->ctxt;
+
+ tidinv = dd->tidinvalid;
+ tidbase = (u64 __iomem *)
+ ((char __iomem *)(dd->kregbase) +
+ dd->rcvtidbase +
+ ctxt * dd->rcvtidcnt * sizeof(*tidbase));
+
+ for (i = 0; i < dd->rcvtidcnt; i++)
+ /* use func pointer because could be one of two funcs */
+ dd->f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED,
+ tidinv);
+
+ tidbase = (u64 __iomem *)
+ ((char __iomem *)(dd->kregbase) +
+ dd->rcvegrbase +
+ rcd->rcvegr_tid_base * sizeof(*tidbase));
+
+ for (i = 0; i < rcd->rcvegrcnt; i++)
+ /* use func pointer because could be one of two funcs */
+ dd->f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EAGER,
+ tidinv);
+}
+
+/**
+ * qib_6120_tidtemplate - setup constants for TID updates
+ * @dd: the qlogic_ib device
+ *
+ * We setup stuff that we use a lot, to avoid calculating each time
+ */
+static void qib_6120_tidtemplate(struct qib_devdata *dd)
+{
+ u32 egrsize = dd->rcvegrbufsize;
+
+ /*
+ * For now, we always allocate 4KB buffers (at init) so we can
+ * receive max size packets. We may want a module parameter to
+ * specify 2KB or 4KB and/or make be per ctxt instead of per device
+ * for those who want to reduce memory footprint. Note that the
+ * rcvhdrentsize size must be large enough to hold the largest
+ * IB header (currently 96 bytes) that we expect to handle (plus of
+ * course the 2 dwords of RHF).
+ */
+ if (egrsize == 2048)
+ dd->tidtemplate = 1U << 29;
+ else if (egrsize == 4096)
+ dd->tidtemplate = 2U << 29;
+ dd->tidinvalid = 0;
+}
+
+int __attribute__((weak)) qib_unordered_wc(void)
+{
+ return 0;
+}
+
+/**
+ * qib_6120_get_base_info - set chip-specific flags for user code
+ * @rcd: the qlogic_ib ctxt
+ * @kbase: qib_base_info pointer
+ *
+ * We set the PCIE flag because the lower bandwidth on PCIe vs
+ * HyperTransport can affect some user packet algorithms.
+ */
+static int qib_6120_get_base_info(struct qib_ctxtdata *rcd,
+ struct qib_base_info *kinfo)
+{
+ if (qib_unordered_wc())
+ kinfo->spi_runtime_flags |= QIB_RUNTIME_FORCE_WC_ORDER;
+
+ kinfo->spi_runtime_flags |= QIB_RUNTIME_PCIE |
+ QIB_RUNTIME_FORCE_PIOAVAIL | QIB_RUNTIME_PIO_REGSWAPPED;
+ return 0;
+}
+
+
+static struct qib_message_header *
+qib_6120_get_msgheader(struct qib_devdata *dd, __le32 *rhf_addr)
+{
+ return (struct qib_message_header *)
+ &rhf_addr[sizeof(u64) / sizeof(u32)];
+}
+
+static void qib_6120_config_ctxts(struct qib_devdata *dd)
+{
+ dd->ctxtcnt = qib_read_kreg32(dd, kr_portcnt);
+ if (qib_n_krcv_queues > 1) {
+ dd->first_user_ctxt = qib_n_krcv_queues * dd->num_pports;
+ if (dd->first_user_ctxt > dd->ctxtcnt)
+ dd->first_user_ctxt = dd->ctxtcnt;
+ dd->qpn_mask = dd->first_user_ctxt <= 2 ? 2 : 6;
+ } else
+ dd->first_user_ctxt = dd->num_pports;
+ dd->n_krcv_queues = dd->first_user_ctxt;
+}
+
+static void qib_update_6120_usrhead(struct qib_ctxtdata *rcd, u64 hd,
+ u32 updegr, u32 egrhd)
+{
+ qib_write_ureg(rcd->dd, ur_rcvhdrhead, hd, rcd->ctxt);
+ if (updegr)
+ qib_write_ureg(rcd->dd, ur_rcvegrindexhead, egrhd, rcd->ctxt);
+}
+
+static u32 qib_6120_hdrqempty(struct qib_ctxtdata *rcd)
+{
+ u32 head, tail;
+
+ head = qib_read_ureg32(rcd->dd, ur_rcvhdrhead, rcd->ctxt);
+ if (rcd->rcvhdrtail_kvaddr)
+ tail = qib_get_rcvhdrtail(rcd);
+ else
+ tail = qib_read_ureg32(rcd->dd, ur_rcvhdrtail, rcd->ctxt);
+ return head == tail;
+}
+
+/*
+ * Used when we close any ctxt, for DMA already in flight
+ * at close. Can't be done until we know hdrq size, so not
+ * early in chip init.
+ */
+static void alloc_dummy_hdrq(struct qib_devdata *dd)
+{
+ dd->cspec->dummy_hdrq = dma_alloc_coherent(&dd->pcidev->dev,
+ dd->rcd[0]->rcvhdrq_size,
+ &dd->cspec->dummy_hdrq_phys,
+ GFP_KERNEL | __GFP_COMP);
+ if (!dd->cspec->dummy_hdrq) {
+ qib_devinfo(dd->pcidev, "Couldn't allocate dummy hdrq\n");
+ /* fallback to just 0'ing */
+ dd->cspec->dummy_hdrq_phys = 0UL;
+ }
+}
+
+/*
+ * Modify the RCVCTRL register in chip-specific way. This
+ * is a function because bit positions and (future) register
+ * location is chip-specific, but the needed operations are
+ * generic. <op> is a bit-mask because we often want to
+ * do multiple modifications.
+ */
+static void rcvctrl_6120_mod(struct qib_pportdata *ppd, unsigned int op,
+ int ctxt)
+{
+ struct qib_devdata *dd = ppd->dd;
+ u64 mask, val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->cspec->rcvmod_lock, flags);
+
+ if (op & QIB_RCVCTRL_TAILUPD_ENB)
+ dd->rcvctrl |= (1ULL << QLOGIC_IB_R_TAILUPD_SHIFT);
+ if (op & QIB_RCVCTRL_TAILUPD_DIS)
+ dd->rcvctrl &= ~(1ULL << QLOGIC_IB_R_TAILUPD_SHIFT);
+ if (op & QIB_RCVCTRL_PKEY_ENB)
+ dd->rcvctrl &= ~(1ULL << IBA6120_R_PKEY_DIS_SHIFT);
+ if (op & QIB_RCVCTRL_PKEY_DIS)
+ dd->rcvctrl |= (1ULL << IBA6120_R_PKEY_DIS_SHIFT);
+ if (ctxt < 0)
+ mask = (1ULL << dd->ctxtcnt) - 1;
+ else
+ mask = (1ULL << ctxt);
+ if (op & QIB_RCVCTRL_CTXT_ENB) {
+ /* always done for specific ctxt */
+ dd->rcvctrl |= (mask << SYM_LSB(RcvCtrl, PortEnable));
+ if (!(dd->flags & QIB_NODMA_RTAIL))
+ dd->rcvctrl |= 1ULL << QLOGIC_IB_R_TAILUPD_SHIFT;
+ /* Write these registers before the context is enabled. */
+ qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr, ctxt,
+ dd->rcd[ctxt]->rcvhdrqtailaddr_phys);
+ qib_write_kreg_ctxt(dd, kr_rcvhdraddr, ctxt,
+ dd->rcd[ctxt]->rcvhdrq_phys);
+
+ if (ctxt == 0 && !dd->cspec->dummy_hdrq)
+ alloc_dummy_hdrq(dd);
+ }
+ if (op & QIB_RCVCTRL_CTXT_DIS)
+ dd->rcvctrl &= ~(mask << SYM_LSB(RcvCtrl, PortEnable));
+ if (op & QIB_RCVCTRL_INTRAVAIL_ENB)
+ dd->rcvctrl |= (mask << QLOGIC_IB_R_INTRAVAIL_SHIFT);
+ if (op & QIB_RCVCTRL_INTRAVAIL_DIS)
+ dd->rcvctrl &= ~(mask << QLOGIC_IB_R_INTRAVAIL_SHIFT);
+ qib_write_kreg(dd, kr_rcvctrl, dd->rcvctrl);
+ if ((op & QIB_RCVCTRL_INTRAVAIL_ENB) && dd->rhdrhead_intr_off) {
+ /* arm rcv interrupt */
+ val = qib_read_ureg32(dd, ur_rcvhdrhead, ctxt) |
+ dd->rhdrhead_intr_off;
+ qib_write_ureg(dd, ur_rcvhdrhead, val, ctxt);
+ }
+ if (op & QIB_RCVCTRL_CTXT_ENB) {
+ /*
+ * Init the context registers also; if we were
+ * disabled, tail and head should both be zero
+ * already from the enable, but since we don't
+ * know, we have to do it explictly.
+ */
+ val = qib_read_ureg32(dd, ur_rcvegrindextail, ctxt);
+ qib_write_ureg(dd, ur_rcvegrindexhead, val, ctxt);
+
+ val = qib_read_ureg32(dd, ur_rcvhdrtail, ctxt);
+ dd->rcd[ctxt]->head = val;
+ /* If kctxt, interrupt on next receive. */
+ if (ctxt < dd->first_user_ctxt)
+ val |= dd->rhdrhead_intr_off;
+ qib_write_ureg(dd, ur_rcvhdrhead, val, ctxt);
+ }
+ if (op & QIB_RCVCTRL_CTXT_DIS) {
+ /*
+ * Be paranoid, and never write 0's to these, just use an
+ * unused page. Of course,
+ * rcvhdraddr points to a large chunk of memory, so this
+ * could still trash things, but at least it won't trash
+ * page 0, and by disabling the ctxt, it should stop "soon",
+ * even if a packet or two is in already in flight after we
+ * disabled the ctxt. Only 6120 has this issue.
+ */
+ if (ctxt >= 0) {
+ qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr, ctxt,
+ dd->cspec->dummy_hdrq_phys);
+ qib_write_kreg_ctxt(dd, kr_rcvhdraddr, ctxt,
+ dd->cspec->dummy_hdrq_phys);
+ } else {
+ unsigned i;
+
+ for (i = 0; i < dd->cfgctxts; i++) {
+ qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr,
+ i, dd->cspec->dummy_hdrq_phys);
+ qib_write_kreg_ctxt(dd, kr_rcvhdraddr,
+ i, dd->cspec->dummy_hdrq_phys);
+ }
+ }
+ }
+ spin_unlock_irqrestore(&dd->cspec->rcvmod_lock, flags);
+}
+
+/*
+ * Modify the SENDCTRL register in chip-specific way. This
+ * is a function there may be multiple such registers with
+ * slightly different layouts. Only operations actually used
+ * are implemented yet.
+ * Chip requires no back-back sendctrl writes, so write
+ * scratch register after writing sendctrl
+ */
+static void sendctrl_6120_mod(struct qib_pportdata *ppd, u32 op)
+{
+ struct qib_devdata *dd = ppd->dd;
+ u64 tmp_dd_sendctrl;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dd->sendctrl_lock, flags);
+
+ /* First the ones that are "sticky", saved in shadow */
+ if (op & QIB_SENDCTRL_CLEAR)
+ dd->sendctrl = 0;
+ if (op & QIB_SENDCTRL_SEND_DIS)
+ dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOEnable);
+ else if (op & QIB_SENDCTRL_SEND_ENB)
+ dd->sendctrl |= SYM_MASK(SendCtrl, PIOEnable);
+ if (op & QIB_SENDCTRL_AVAIL_DIS)
+ dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOBufAvailUpd);
+ else if (op & QIB_SENDCTRL_AVAIL_ENB)
+ dd->sendctrl |= SYM_MASK(SendCtrl, PIOBufAvailUpd);
+
+ if (op & QIB_SENDCTRL_DISARM_ALL) {
+ u32 i, last;
+
+ tmp_dd_sendctrl = dd->sendctrl;
+ /*
+ * disarm any that are not yet launched, disabling sends
+ * and updates until done.
+ */
+ last = dd->piobcnt2k + dd->piobcnt4k;
+ tmp_dd_sendctrl &=
+ ~(SYM_MASK(SendCtrl, PIOEnable) |
+ SYM_MASK(SendCtrl, PIOBufAvailUpd));
+ for (i = 0; i < last; i++) {
+ qib_write_kreg(dd, kr_sendctrl, tmp_dd_sendctrl |
+ SYM_MASK(SendCtrl, Disarm) | i);
+ qib_write_kreg(dd, kr_scratch, 0);
+ }
+ }
+
+ tmp_dd_sendctrl = dd->sendctrl;
+
+ if (op & QIB_SENDCTRL_FLUSH)
+ tmp_dd_sendctrl |= SYM_MASK(SendCtrl, Abort);
+ if (op & QIB_SENDCTRL_DISARM)
+ tmp_dd_sendctrl |= SYM_MASK(SendCtrl, Disarm) |
+ ((op & QIB_6120_SendCtrl_DisarmPIOBuf_RMASK) <<
+ SYM_LSB(SendCtrl, DisarmPIOBuf));
+ if (op & QIB_SENDCTRL_AVAIL_BLIP)
+ tmp_dd_sendctrl &= ~SYM_MASK(SendCtrl, PIOBufAvailUpd);
+
+ qib_write_kreg(dd, kr_sendctrl, tmp_dd_sendctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+
+ if (op & QIB_SENDCTRL_AVAIL_BLIP) {
+ qib_write_kreg(dd, kr_sendctrl, dd->sendctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+ }
+
+ spin_unlock_irqrestore(&dd->sendctrl_lock, flags);
+
+ if (op & QIB_SENDCTRL_FLUSH) {
+ u32 v;
+ /*
+ * ensure writes have hit chip, then do a few
+ * more reads, to allow DMA of pioavail registers
+ * to occur, so in-memory copy is in sync with
+ * the chip. Not always safe to sleep.
+ */
+ v = qib_read_kreg32(dd, kr_scratch);
+ qib_write_kreg(dd, kr_scratch, v);
+ v = qib_read_kreg32(dd, kr_scratch);
+ qib_write_kreg(dd, kr_scratch, v);
+ qib_read_kreg32(dd, kr_scratch);
+ }
+}
+
+/**
+ * qib_portcntr_6120 - read a per-port counter
+ * @dd: the qlogic_ib device
+ * @creg: the counter to snapshot
+ */
+static u64 qib_portcntr_6120(struct qib_pportdata *ppd, u32 reg)
+{
+ u64 ret = 0ULL;
+ struct qib_devdata *dd = ppd->dd;
+ u16 creg;
+ /* 0xffff for unimplemented or synthesized counters */
+ static const u16 xlator[] = {
+ [QIBPORTCNTR_PKTSEND] = cr_pktsend,
+ [QIBPORTCNTR_WORDSEND] = cr_wordsend,
+ [QIBPORTCNTR_PSXMITDATA] = 0xffff,
+ [QIBPORTCNTR_PSXMITPKTS] = 0xffff,
+ [QIBPORTCNTR_PSXMITWAIT] = 0xffff,
+ [QIBPORTCNTR_SENDSTALL] = cr_sendstall,
+ [QIBPORTCNTR_PKTRCV] = cr_pktrcv,
+ [QIBPORTCNTR_PSRCVDATA] = 0xffff,
+ [QIBPORTCNTR_PSRCVPKTS] = 0xffff,
+ [QIBPORTCNTR_RCVEBP] = cr_rcvebp,
+ [QIBPORTCNTR_RCVOVFL] = cr_rcvovfl,
+ [QIBPORTCNTR_WORDRCV] = cr_wordrcv,
+ [QIBPORTCNTR_RXDROPPKT] = cr_rxdroppkt,
+ [QIBPORTCNTR_RXLOCALPHYERR] = 0xffff,
+ [QIBPORTCNTR_RXVLERR] = 0xffff,
+ [QIBPORTCNTR_ERRICRC] = cr_erricrc,
+ [QIBPORTCNTR_ERRVCRC] = cr_errvcrc,
+ [QIBPORTCNTR_ERRLPCRC] = cr_errlpcrc,
+ [QIBPORTCNTR_BADFORMAT] = cr_badformat,
+ [QIBPORTCNTR_ERR_RLEN] = cr_err_rlen,
+ [QIBPORTCNTR_IBSYMBOLERR] = cr_ibsymbolerr,
+ [QIBPORTCNTR_INVALIDRLEN] = cr_invalidrlen,
+ [QIBPORTCNTR_UNSUPVL] = cr_txunsupvl,
+ [QIBPORTCNTR_EXCESSBUFOVFL] = 0xffff,
+ [QIBPORTCNTR_ERRLINK] = cr_errlink,
+ [QIBPORTCNTR_IBLINKDOWN] = cr_iblinkdown,
+ [QIBPORTCNTR_IBLINKERRRECOV] = cr_iblinkerrrecov,
+ [QIBPORTCNTR_LLI] = 0xffff,
+ [QIBPORTCNTR_PSINTERVAL] = 0xffff,
+ [QIBPORTCNTR_PSSTART] = 0xffff,
+ [QIBPORTCNTR_PSSTAT] = 0xffff,
+ [QIBPORTCNTR_VL15PKTDROP] = 0xffff,
+ [QIBPORTCNTR_ERRPKEY] = cr_errpkey,
+ [QIBPORTCNTR_KHDROVFL] = 0xffff,
+ };
+
+ if (reg >= ARRAY_SIZE(xlator)) {
+ qib_devinfo(ppd->dd->pcidev,
+ "Unimplemented portcounter %u\n", reg);
+ goto done;
+ }
+ creg = xlator[reg];
+
+ /* handle counters requests not implemented as chip counters */
+ if (reg == QIBPORTCNTR_LLI)
+ ret = dd->cspec->lli_errs;
+ else if (reg == QIBPORTCNTR_EXCESSBUFOVFL)
+ ret = dd->cspec->overrun_thresh_errs;
+ else if (reg == QIBPORTCNTR_KHDROVFL) {
+ int i;
+
+ /* sum over all kernel contexts */
+ for (i = 0; i < dd->first_user_ctxt; i++)
+ ret += read_6120_creg32(dd, cr_portovfl + i);
+ } else if (reg == QIBPORTCNTR_PSSTAT)
+ ret = dd->cspec->pma_sample_status;
+ if (creg == 0xffff)
+ goto done;
+
+ /*
+ * only fast incrementing counters are 64bit; use 32 bit reads to
+ * avoid two independent reads when on opteron
+ */
+ if (creg == cr_wordsend || creg == cr_wordrcv ||
+ creg == cr_pktsend || creg == cr_pktrcv)
+ ret = read_6120_creg(dd, creg);
+ else
+ ret = read_6120_creg32(dd, creg);
+ if (creg == cr_ibsymbolerr) {
+ if (dd->cspec->ibdeltainprog)
+ ret -= ret - dd->cspec->ibsymsnap;
+ ret -= dd->cspec->ibsymdelta;
+ } else if (creg == cr_iblinkerrrecov) {
+ if (dd->cspec->ibdeltainprog)
+ ret -= ret - dd->cspec->iblnkerrsnap;
+ ret -= dd->cspec->iblnkerrdelta;
+ }
+ if (reg == QIBPORTCNTR_RXDROPPKT) /* add special cased count */
+ ret += dd->cspec->rxfc_unsupvl_errs;
+
+done:
+ return ret;
+}
+
+/*
+ * Device counter names (not port-specific), one line per stat,
+ * single string. Used by utilities like ipathstats to print the stats
+ * in a way which works for different versions of drivers, without changing
+ * the utility. Names need to be 12 chars or less (w/o newline), for proper
+ * display by utility.
+ * Non-error counters are first.
+ * Start of "error" conters is indicated by a leading "E " on the first
+ * "error" counter, and doesn't count in label length.
+ * The EgrOvfl list needs to be last so we truncate them at the configured
+ * context count for the device.
+ * cntr6120indices contains the corresponding register indices.
+ */
+static const char cntr6120names[] =
+ "Interrupts\n"
+ "HostBusStall\n"
+ "E RxTIDFull\n"
+ "RxTIDInvalid\n"
+ "Ctxt0EgrOvfl\n"
+ "Ctxt1EgrOvfl\n"
+ "Ctxt2EgrOvfl\n"
+ "Ctxt3EgrOvfl\n"
+ "Ctxt4EgrOvfl\n";
+
+static const size_t cntr6120indices[] = {
+ cr_lbint,
+ cr_lbflowstall,
+ cr_errtidfull,
+ cr_errtidvalid,
+ cr_portovfl + 0,
+ cr_portovfl + 1,
+ cr_portovfl + 2,
+ cr_portovfl + 3,
+ cr_portovfl + 4,
+};
+
+/*
+ * same as cntr6120names and cntr6120indices, but for port-specific counters.
+ * portcntr6120indices is somewhat complicated by some registers needing
+ * adjustments of various kinds, and those are ORed with _PORT_VIRT_FLAG
+ */
+static const char portcntr6120names[] =
+ "TxPkt\n"
+ "TxFlowPkt\n"
+ "TxWords\n"
+ "RxPkt\n"
+ "RxFlowPkt\n"
+ "RxWords\n"
+ "TxFlowStall\n"
+ "E IBStatusChng\n"
+ "IBLinkDown\n"
+ "IBLnkRecov\n"
+ "IBRxLinkErr\n"
+ "IBSymbolErr\n"
+ "RxLLIErr\n"
+ "RxBadFormat\n"
+ "RxBadLen\n"
+ "RxBufOvrfl\n"
+ "RxEBP\n"
+ "RxFlowCtlErr\n"
+ "RxICRCerr\n"
+ "RxLPCRCerr\n"
+ "RxVCRCerr\n"
+ "RxInvalLen\n"
+ "RxInvalPKey\n"
+ "RxPktDropped\n"
+ "TxBadLength\n"
+ "TxDropped\n"
+ "TxInvalLen\n"
+ "TxUnderrun\n"
+ "TxUnsupVL\n"
+ ;
+
+#define _PORT_VIRT_FLAG 0x8000 /* "virtual", need adjustments */
+static const size_t portcntr6120indices[] = {
+ QIBPORTCNTR_PKTSEND | _PORT_VIRT_FLAG,
+ cr_pktsendflow,
+ QIBPORTCNTR_WORDSEND | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_PKTRCV | _PORT_VIRT_FLAG,
+ cr_pktrcvflowctrl,
+ QIBPORTCNTR_WORDRCV | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_SENDSTALL | _PORT_VIRT_FLAG,
+ cr_ibstatuschange,
+ QIBPORTCNTR_IBLINKDOWN | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_IBLINKERRRECOV | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_ERRLINK | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_IBSYMBOLERR | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_LLI | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_BADFORMAT | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_ERR_RLEN | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_RCVOVFL | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_RCVEBP | _PORT_VIRT_FLAG,
+ cr_rcvflowctrl_err,
+ QIBPORTCNTR_ERRICRC | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_ERRLPCRC | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_ERRVCRC | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_INVALIDRLEN | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_ERRPKEY | _PORT_VIRT_FLAG,
+ QIBPORTCNTR_RXDROPPKT | _PORT_VIRT_FLAG,
+ cr_invalidslen,
+ cr_senddropped,
+ cr_errslen,
+ cr_sendunderrun,
+ cr_txunsupvl,
+};
+
+/* do all the setup to make the counter reads efficient later */
+static void init_6120_cntrnames(struct qib_devdata *dd)
+{
+ int i, j = 0;
+ char *s;
+
+ for (i = 0, s = (char *)cntr6120names; s && j <= dd->cfgctxts;
+ i++) {
+ /* we always have at least one counter before the egrovfl */
+ if (!j && !strncmp("Ctxt0EgrOvfl", s + 1, 12))
+ j = 1;
+ s = strchr(s + 1, '\n');
+ if (s && j)
+ j++;
+ }
+ dd->cspec->ncntrs = i;
+ if (!s)
+ /* full list; size is without terminating null */
+ dd->cspec->cntrnamelen = sizeof(cntr6120names) - 1;
+ else
+ dd->cspec->cntrnamelen = 1 + s - cntr6120names;
+ dd->cspec->cntrs = kmalloc(dd->cspec->ncntrs
+ * sizeof(u64), GFP_KERNEL);
+ if (!dd->cspec->cntrs)
+ qib_dev_err(dd, "Failed allocation for counters\n");
+
+ for (i = 0, s = (char *)portcntr6120names; s; i++)
+ s = strchr(s + 1, '\n');
+ dd->cspec->nportcntrs = i - 1;
+ dd->cspec->portcntrnamelen = sizeof(portcntr6120names) - 1;
+ dd->cspec->portcntrs = kmalloc(dd->cspec->nportcntrs
+ * sizeof(u64), GFP_KERNEL);
+ if (!dd->cspec->portcntrs)
+ qib_dev_err(dd, "Failed allocation for portcounters\n");
+}
+
+static u32 qib_read_6120cntrs(struct qib_devdata *dd, loff_t pos, char **namep,
+ u64 **cntrp)
+{
+ u32 ret;
+
+ if (namep) {
+ ret = dd->cspec->cntrnamelen;
+ if (pos >= ret)
+ ret = 0; /* final read after getting everything */
+ else
+ *namep = (char *)cntr6120names;
+ } else {
+ u64 *cntr = dd->cspec->cntrs;
+ int i;
+
+ ret = dd->cspec->ncntrs * sizeof(u64);
+ if (!cntr || pos >= ret) {
+ /* everything read, or couldn't get memory */
+ ret = 0;
+ goto done;
+ }
+ if (pos >= ret) {
+ ret = 0; /* final read after getting everything */
+ goto done;
+ }
+ *cntrp = cntr;
+ for (i = 0; i < dd->cspec->ncntrs; i++)
+ *cntr++ = read_6120_creg32(dd, cntr6120indices[i]);
+ }
+done:
+ return ret;
+}
+
+static u32 qib_read_6120portcntrs(struct qib_devdata *dd, loff_t pos, u32 port,
+ char **namep, u64 **cntrp)
+{
+ u32 ret;
+
+ if (namep) {
+ ret = dd->cspec->portcntrnamelen;
+ if (pos >= ret)
+ ret = 0; /* final read after getting everything */
+ else
+ *namep = (char *)portcntr6120names;
+ } else {
+ u64 *cntr = dd->cspec->portcntrs;
+ struct qib_pportdata *ppd = &dd->pport[port];
+ int i;
+
+ ret = dd->cspec->nportcntrs * sizeof(u64);
+ if (!cntr || pos >= ret) {
+ /* everything read, or couldn't get memory */
+ ret = 0;
+ goto done;
+ }
+ *cntrp = cntr;
+ for (i = 0; i < dd->cspec->nportcntrs; i++) {
+ if (portcntr6120indices[i] & _PORT_VIRT_FLAG)
+ *cntr++ = qib_portcntr_6120(ppd,
+ portcntr6120indices[i] &
+ ~_PORT_VIRT_FLAG);
+ else
+ *cntr++ = read_6120_creg32(dd,
+ portcntr6120indices[i]);
+ }
+ }
+done:
+ return ret;
+}
+
+static void qib_chk_6120_errormask(struct qib_devdata *dd)
+{
+ static u32 fixed;
+ u32 ctrl;
+ unsigned long errormask;
+ unsigned long hwerrs;
+
+ if (!dd->cspec->errormask || !(dd->flags & QIB_INITTED))
+ return;
+
+ errormask = qib_read_kreg64(dd, kr_errmask);
+
+ if (errormask == dd->cspec->errormask)
+ return;
+ fixed++;
+
+ hwerrs = qib_read_kreg64(dd, kr_hwerrstatus);
+ ctrl = qib_read_kreg32(dd, kr_control);
+
+ qib_write_kreg(dd, kr_errmask,
+ dd->cspec->errormask);
+
+ if ((hwerrs & dd->cspec->hwerrmask) ||
+ (ctrl & QLOGIC_IB_C_FREEZEMODE)) {
+ qib_write_kreg(dd, kr_hwerrclear, 0ULL);
+ qib_write_kreg(dd, kr_errclear, 0ULL);
+ /* force re-interrupt of pending events, just in case */
+ qib_write_kreg(dd, kr_intclear, 0ULL);
+ qib_devinfo(dd->pcidev,
+ "errormask fixed(%u) %lx->%lx, ctrl %x hwerr %lx\n",
+ fixed, errormask, (unsigned long)dd->cspec->errormask,
+ ctrl, hwerrs);
+ }
+}
+
+/**
+ * qib_get_faststats - get word counters from chip before they overflow
+ * @opaque - contains a pointer to the qlogic_ib device qib_devdata
+ *
+ * This needs more work; in particular, decision on whether we really
+ * need traffic_wds done the way it is
+ * called from add_timer
+ */
+static void qib_get_6120_faststats(unsigned long opaque)
+{
+ struct qib_devdata *dd = (struct qib_devdata *) opaque;
+ struct qib_pportdata *ppd = dd->pport;
+ unsigned long flags;
+ u64 traffic_wds;
+
+ /*
+ * don't access the chip while running diags, or memory diags can
+ * fail
+ */
+ if (!(dd->flags & QIB_INITTED) || dd->diag_client)
+ /* but re-arm the timer, for diags case; won't hurt other */
+ goto done;
+
+ /*
+ * We now try to maintain an activity timer, based on traffic
+ * exceeding a threshold, so we need to check the word-counts
+ * even if they are 64-bit.
+ */
+ traffic_wds = qib_portcntr_6120(ppd, cr_wordsend) +
+ qib_portcntr_6120(ppd, cr_wordrcv);
+ spin_lock_irqsave(&dd->eep_st_lock, flags);
+ traffic_wds -= dd->traffic_wds;
+ dd->traffic_wds += traffic_wds;
+ if (traffic_wds >= QIB_TRAFFIC_ACTIVE_THRESHOLD)
+ atomic_add(5, &dd->active_time); /* S/B #define */
+ spin_unlock_irqrestore(&dd->eep_st_lock, flags);
+
+ qib_chk_6120_errormask(dd);
+done:
+ mod_timer(&dd->stats_timer, jiffies + HZ * ACTIVITY_TIMER);
+}
+
+/* no interrupt fallback for these chips */
+static int qib_6120_nointr_fallback(struct qib_devdata *dd)
+{
+ return 0;
+}
+
+/*
+ * reset the XGXS (between serdes and IBC). Slightly less intrusive
+ * than resetting the IBC or external link state, and useful in some
+ * cases to cause some retraining. To do this right, we reset IBC
+ * as well.
+ */
+static void qib_6120_xgxs_reset(struct qib_pportdata *ppd)
+{
+ u64 val, prev_val;
+ struct qib_devdata *dd = ppd->dd;
+
+ prev_val = qib_read_kreg64(dd, kr_xgxs_cfg);
+ val = prev_val | QLOGIC_IB_XGXS_RESET;
+ prev_val &= ~QLOGIC_IB_XGXS_RESET; /* be sure */
+ qib_write_kreg(dd, kr_control,
+ dd->control & ~QLOGIC_IB_C_LINKENABLE);
+ qib_write_kreg(dd, kr_xgxs_cfg, val);
+ qib_read_kreg32(dd, kr_scratch);
+ qib_write_kreg(dd, kr_xgxs_cfg, prev_val);
+ qib_write_kreg(dd, kr_control, dd->control);
+}
+
+static int qib_6120_get_ib_cfg(struct qib_pportdata *ppd, int which)
+{
+ int ret;
+
+ switch (which) {
+ case QIB_IB_CFG_LWID:
+ ret = ppd->link_width_active;
+ break;
+
+ case QIB_IB_CFG_SPD:
+ ret = ppd->link_speed_active;
+ break;
+
+ case QIB_IB_CFG_LWID_ENB:
+ ret = ppd->link_width_enabled;
+ break;
+
+ case QIB_IB_CFG_SPD_ENB:
+ ret = ppd->link_speed_enabled;
+ break;
+
+ case QIB_IB_CFG_OP_VLS:
+ ret = ppd->vls_operational;
+ break;
+
+ case QIB_IB_CFG_VL_HIGH_CAP:
+ ret = 0;
+ break;
+
+ case QIB_IB_CFG_VL_LOW_CAP:
+ ret = 0;
+ break;
+
+ case QIB_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
+ ret = SYM_FIELD(ppd->dd->cspec->ibcctrl, IBCCtrl,
+ OverrunThreshold);
+ break;
+
+ case QIB_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
+ ret = SYM_FIELD(ppd->dd->cspec->ibcctrl, IBCCtrl,
+ PhyerrThreshold);
+ break;
+
+ case QIB_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
+ /* will only take effect when the link state changes */
+ ret = (ppd->dd->cspec->ibcctrl &
+ SYM_MASK(IBCCtrl, LinkDownDefaultState)) ?
+ IB_LINKINITCMD_SLEEP : IB_LINKINITCMD_POLL;
+ break;
+
+ case QIB_IB_CFG_HRTBT: /* Get Heartbeat off/enable/auto */
+ ret = 0; /* no heartbeat on this chip */
+ break;
+
+ case QIB_IB_CFG_PMA_TICKS:
+ ret = 250; /* 1 usec. */
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ return ret;
+}
+
+/*
+ * We assume range checking is already done, if needed.
+ */
+static int qib_6120_set_ib_cfg(struct qib_pportdata *ppd, int which, u32 val)
+{
+ struct qib_devdata *dd = ppd->dd;
+ int ret = 0;
+ u64 val64;
+ u16 lcmd, licmd;
+
+ switch (which) {
+ case QIB_IB_CFG_LWID_ENB:
+ ppd->link_width_enabled = val;
+ break;
+
+ case QIB_IB_CFG_SPD_ENB:
+ ppd->link_speed_enabled = val;
+ break;
+
+ case QIB_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
+ val64 = SYM_FIELD(dd->cspec->ibcctrl, IBCCtrl,
+ OverrunThreshold);
+ if (val64 != val) {
+ dd->cspec->ibcctrl &=
+ ~SYM_MASK(IBCCtrl, OverrunThreshold);
+ dd->cspec->ibcctrl |= (u64) val <<
+ SYM_LSB(IBCCtrl, OverrunThreshold);
+ qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+ }
+ break;
+
+ case QIB_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
+ val64 = SYM_FIELD(dd->cspec->ibcctrl, IBCCtrl,
+ PhyerrThreshold);
+ if (val64 != val) {
+ dd->cspec->ibcctrl &=
+ ~SYM_MASK(IBCCtrl, PhyerrThreshold);
+ dd->cspec->ibcctrl |= (u64) val <<
+ SYM_LSB(IBCCtrl, PhyerrThreshold);
+ qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+ }
+ break;
+
+ case QIB_IB_CFG_PKEYS: /* update pkeys */
+ val64 = (u64) ppd->pkeys[0] | ((u64) ppd->pkeys[1] << 16) |
+ ((u64) ppd->pkeys[2] << 32) |
+ ((u64) ppd->pkeys[3] << 48);
+ qib_write_kreg(dd, kr_partitionkey, val64);
+ break;
+
+ case QIB_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
+ /* will only take effect when the link state changes */
+ if (val == IB_LINKINITCMD_POLL)
+ dd->cspec->ibcctrl &=
+ ~SYM_MASK(IBCCtrl, LinkDownDefaultState);
+ else /* SLEEP */
+ dd->cspec->ibcctrl |=
+ SYM_MASK(IBCCtrl, LinkDownDefaultState);
+ qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+ break;
+
+ case QIB_IB_CFG_MTU: /* update the MTU in IBC */
+ /*
+ * Update our housekeeping variables, and set IBC max
+ * size, same as init code; max IBC is max we allow in
+ * buffer, less the qword pbc, plus 1 for ICRC, in dwords
+ * Set even if it's unchanged, print debug message only
+ * on changes.
+ */
+ val = (ppd->ibmaxlen >> 2) + 1;
+ dd->cspec->ibcctrl &= ~SYM_MASK(IBCCtrl, MaxPktLen);
+ dd->cspec->ibcctrl |= (u64)val <<
+ SYM_LSB(IBCCtrl, MaxPktLen);
+ qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
+ qib_write_kreg(dd, kr_scratch, 0);
+ break;
+
+ case QIB_IB_CFG_LSTATE: /* set the IB link state */
+ switch (val & 0xffff0000) {
+ case IB_LINKCMD_DOWN:
+ lcmd = QLOGIC_IB_IBCC_LINKCMD_DOWN;
+ if (!dd->cspec->ibdeltainprog) {
+ dd->cspec->ibdeltainprog = 1;
+ dd->cspec->ibsymsnap =
+ read_6120_creg32(dd, cr_ibsymbolerr);
+ dd->cspec->iblnkerrsnap =
+ read_6120_creg32(dd, cr_iblinkerrrecov);
+ }
+ break;
+
+ case IB_LINKCMD_ARMED:
+ lcmd = QLOGIC_IB_IBCC_LINKCMD_ARMED;
+ break;
+
+ case IB_LINKCMD_ACTIVE:
+ lcmd = QLOGIC_IB_IBCC_LINKCMD_ACTIVE;
+ break;
+
+ default:
+ ret = -EINVAL;
+ qib_dev_err(dd, "bad linkcmd req 0x%x\n", val >> 16);
+ goto bail;
+ }
+ switch (val & 0xffff) {
+ case IB_LINKINITCMD_NOP:
+ licmd = 0;
+ break;
+
+ case IB_LINKINITCMD_POLL:
+ licmd = QLOGIC_IB_IBCC_LINKINITCMD_POLL;
+ break;
+
+ case IB_LINKINITCMD_SLEEP:
+ licmd = QLOGIC_IB_IBCC_LINKINITCMD_SLEEP;
+ break;
+
+ case IB_LINKINITCMD_DISABLE:
+ licmd = QLOGIC_IB_IBCC_LINKINITCMD_DISABLE;
+ break;
+
+ default:
+ ret = -EINVAL;
+ qib_dev_err(dd, "bad linkinitcmd req 0x%x\n",
+ val & 0xffff);
+ goto bail;
+ }
+ qib_set_ib_6120_lstate(ppd, lcmd, licmd);
+ goto bail;
+
+ case QIB_IB_CFG_HRTBT:
+ ret = -EINVAL;
+ break;
+
+ default:
+ ret = -EINVAL;
+ }
+bail:
+ return ret;
+}
+
+static int qib_6120_set_loopback(struct qib_pportdata *ppd, const char *what)
+{
+ int ret = 0;
+ if (!strncmp(what, "ibc", 3)) {
+ ppd->dd->cspec->ibcctrl |= SYM_MASK(IBCCtrl, Loopback);
+ qib_devinfo(ppd->dd->pcidev, "Enabling IB%u:%u IBC loopback\n",
+ ppd->dd->unit, ppd->port);
+ } else if (!strncmp(what, "off", 3)) {
+ ppd->dd->cspec->ibcctrl &= ~SYM_MASK(IBCCtrl, Loopback);
+ qib_devinfo(ppd->dd->pcidev, "Disabling IB%u:%u IBC loopback "
+ "(normal)\n", ppd->dd->unit, ppd->port);
+ } else
+ ret = -EINVAL;
+ if (!ret) {
+ qib_write_kreg(ppd->dd, kr_ibcctrl, ppd->dd->cspec->ibcctrl);
+ qib_write_kreg(ppd->dd, kr_scratch, 0);
+ }
+ return ret;
+}
+
+static void pma_6120_timer(unsigned long data)
+{
+ struct qib_pportdata *ppd = (struct qib_pportdata *)data;
+ struct qib_chip_specific *cs = ppd->dd->cspec;
+ struct qib_ibport *ibp = &ppd->ibport_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ibp->lock, flags);
+ if (cs->pma_sample_status == IB_PMA_SAMPLE_STATUS_STARTED) {
+ cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_RUNNING;
+ qib_snapshot_counters(ppd, &cs->sword, &cs->rword,
+ &cs->spkts, &cs->rpkts, &cs->xmit_wait);
+ mod_timer(&cs->pma_timer,
+ jiffies + usecs_to_jiffies(ibp->pma_sample_interval));
+ } else if (cs->pma_sample_status == IB_PMA_SAMPLE_STATUS_RUNNING) {
+ u64 ta, tb, tc, td, te;
+
+ cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_DONE;
+ qib_snapshot_counters(ppd, &ta, &tb, &tc, &td, &te);
+
+ cs->sword = ta - cs->sword;
+ cs->rword = tb - cs->rword;
+ cs->spkts = tc - cs->spkts;
+ cs->rpkts = td - cs->rpkts;
+ cs->xmit_wait = te - cs->xmit_wait;
+ }
+ spin_unlock_irqrestore(&ibp->lock, flags);
+}
+
+/*
+ * Note that the caller has the ibp->lock held.
+ */
+static void qib_set_cntr_6120_sample(struct qib_pportdata *ppd, u32 intv,
+ u32 start)
+{
+ struct qib_chip_specific *cs = ppd->dd->cspec;
+
+ if (start && intv) {
+ cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_STARTED;
+ mod_timer(&cs->pma_timer, jiffies + usecs_to_jiffies(start));
+ } else if (intv) {
+ cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_RUNNING;
+ qib_snapshot_counters(ppd, &cs->sword, &cs->rword,
+ &cs->spkts, &cs->rpkts, &cs->xmit_wait);
+ mod_timer(&cs->pma_timer, jiffies + usecs_to_jiffies(intv));
+ } else {
+ cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_DONE;
+ cs->sword = 0;
+ cs->rword = 0;
+ cs->spkts = 0;
+ cs->rpkts = 0;
+ cs->xmit_wait = 0;
+ }
+}
+
+static u32 qib_6120_iblink_state(u64 ibcs)
+{
+ u32 state = (u32)SYM_FIELD(ibcs, IBCStatus, LinkState);
+
+ switch (state) {
+ case IB_6120_L_STATE_INIT:
+ state = IB_PORT_INIT;
+ break;
+ case IB_6120_L_STATE_ARM:
+ state = IB_PORT_ARMED;
+ break;
+ case IB_6120_L_STATE_ACTIVE:
+ /* fall through */
+ case IB_6120_L_STATE_ACT_DEFER:
+ state = IB_PORT_ACTIVE;
+ break;
+ default: /* fall through */
+ case IB_6120_L_STATE_DOWN:
+ state = IB_PORT_DOWN;
+ break;
+ }
+ return state;
+}
+
+/* returns the IBTA port state, rather than the IBC link training state */
+static u8 qib_6120_phys_portstate(u64 ibcs)
+{
+ u8 state = (u8)SYM_FIELD(ibcs, IBCStatus, LinkTrainingState);
+ return qib_6120_physportstate[state];
+}
+
+static int qib_6120_ib_updown(struct qib_pportdata *ppd, int ibup, u64 ibcs)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ppd->lflags_lock, flags);
+ ppd->lflags &= ~QIBL_IB_FORCE_NOTIFY;
+ spin_unlock_irqrestore(&ppd->lflags_lock, flags);
+
+ if (ibup) {
+ if (ppd->dd->cspec->ibdeltainprog) {
+ ppd->dd->cspec->ibdeltainprog = 0;
+ ppd->dd->cspec->ibsymdelta +=
+ read_6120_creg32(ppd->dd, cr_ibsymbolerr) -
+ ppd->dd->cspec->ibsymsnap;
+ ppd->dd->cspec->iblnkerrdelta +=
+ read_6120_creg32(ppd->dd, cr_iblinkerrrecov) -
+ ppd->dd->cspec->iblnkerrsnap;
+ }
+ qib_hol_init(ppd);
+ } else {
+ ppd->dd->cspec->lli_counter = 0;
+ if (!ppd->dd->cspec->ibdeltainprog) {
+ ppd->dd->cspec->ibdeltainprog = 1;
+ ppd->dd->cspec->ibsymsnap =
+ read_6120_creg32(ppd->dd, cr_ibsymbolerr);
+ ppd->dd->cspec->iblnkerrsnap =
+ read_6120_creg32(ppd->dd, cr_iblinkerrrecov);
+ }
+ qib_hol_down(ppd);
+ }
+
+ qib_6120_setup_setextled(ppd, ibup);
+
+ return 0;
+}
+
+/* Does read/modify/write to appropriate registers to
+ * set output and direction bits selected by mask.
+ * these are in their canonical postions (e.g. lsb of
+ * dir will end up in D48 of extctrl on existing chips).
+ * returns contents of GP Inputs.
+ */
+static int gpio_6120_mod(struct qib_devdata *dd, u32 out, u32 dir, u32 mask)
+{
+ u64 read_val, new_out;
+ unsigned long flags;
+
+ if (mask) {
+ /* some bits being written, lock access to GPIO */
+ dir &= mask;
+ out &= mask;
+ spin_lock_irqsave(&dd->cspec->gpio_lock, flags);
+ dd->cspec->extctrl &= ~((u64)mask << SYM_LSB(EXTCtrl, GPIOOe));
+ dd->cspec->extctrl |= ((u64) dir << SYM_LSB(EXTCtrl, GPIOOe));
+ new_out = (dd->cspec->gpio_out & ~mask) | out;
+
+ qib_write_kreg(dd, kr_extctrl, dd->cspec->extctrl);
+ qib_write_kreg(dd, kr_gpio_out, new_out);
+ dd->cspec->gpio_out = new_out;
+ spin_unlock_irqrestore(&dd->cspec->gpio_lock, flags);
+ }
+ /*
+ * It is unlikely that a read at this time would get valid
+ * data on a pin whose direction line was set in the same
+ * call to this function. We include the read here because
+ * that allows us to potentially combine a change on one pin with
+ * a read on another, and because the old code did something like
+ * this.
+ */
+ read_val = qib_read_kreg64(dd, kr_extstatus);
+ return SYM_FIELD(read_val, EXTStatus, GPIOIn);
+}
+
+/*
+ * Read fundamental info we need to use the chip. These are
+ * the registers that describe chip capabilities, and are
+ * saved in shadow registers.
+ */
+static void get_6120_chip_params(struct qib_devdata *dd)
+{
+ u64 val;
+ u32 piobufs;
+ int mtu;
+
+ dd->uregbase = qib_read_kreg32(dd, kr_userregbase);
+
+ dd->rcvtidcnt = qib_read_kreg32(dd, kr_rcvtidcnt);
+ dd->rcvtidbase = qib_read_kreg32(dd, kr_rcvtidbase);
+ dd->rcvegrbase = qib_read_kreg32(dd, kr_rcvegrbase);
+ dd->palign = qib_read_kreg32(dd, kr_palign);
+ dd->piobufbase = qib_read_kreg64(dd, kr_sendpiobufbase);
+ dd->pio2k_bufbase = dd->piobufbase & 0xffffffff;
+
+ dd->rcvhdrcnt = qib_read_kreg32(dd, kr_rcvegrcnt);
+
+ val = qib_read_kreg64(dd, kr_sendpiosize);
+ dd->piosize2k = val & ~0U;
+ dd->piosize4k = val >> 32;
+
+ mtu = ib_mtu_enum_to_int(qib_ibmtu);
+ if (mtu == -1)
+ mtu = QIB_DEFAULT_MTU;
+ dd->pport->ibmtu = (u32)mtu;
+
+ val = qib_read_kreg64(dd, kr_sendpiobufcnt);
+ dd->piobcnt2k = val & ~0U;
+ dd->piobcnt4k = val >> 32;
+ /* these may be adjusted in init_chip_wc_pat() */
+ dd->pio2kbase = (u32 __iomem *)
+ (((char __iomem *)dd->kregbase) + dd->pio2k_bufbase);
+ if (dd->piobcnt4k) {
+ dd->pio4kbase = (u32 __iomem *)
+ (((char __iomem *) dd->kregbase) +
+ (dd->piobufbase >> 32));
+ /*
+ * 4K buffers take 2 pages; we use roundup just to be
+ * paranoid; we calculate it once here, rather than on
+ * ever buf allocate
+ */
+ dd->align4k = ALIGN(dd->piosize4k, dd->palign);
+ }
+
+ piobufs = dd->piobcnt4k + dd->piobcnt2k;
+
+ dd->pioavregs = ALIGN(piobufs, sizeof(u64) * BITS_PER_BYTE / 2) /
+ (sizeof(u64) * BITS_PER_BYTE / 2);
+}
+
+/*
+ * The chip base addresses in cspec and cpspec have to be set
+ * after possible init_chip_wc_pat(), rather than in
+ * get_6120_chip_params(), so split out as separate function
+ */
+static void set_6120_baseaddrs(struct qib_devdata *dd)
+{
+ u32 cregbase;
+ cregbase = qib_read_kreg32(dd, kr_counterregbase);
+ dd->cspec->cregbase = (u64 __iomem *)
+ ((char __iomem *) dd->kregbase + cregbase);
+
+ dd->egrtidbase = (u64 __iomem *)
+ ((char __iomem *) dd->kregbase + dd->rcvegrbase);
+}
+
+/*
+ * Write the final few registers that depend on some of the
+ * init setup. Done late in init, just before bringing up
+ * the serdes.
+ */
+static int qib_late_6120_initreg(struct qib_devdata *dd)
+{
+ int ret = 0;
+ u64 val;
+
+ qib_write_kreg(dd, kr_rcvhdrentsize, dd->rcvhdrentsize);
+ qib_write_kreg(dd, kr_rcvhdrsize, dd->rcvhdrsize);
+ qib_write_kreg(dd, kr_rcvhdrcnt, dd->rcvhdrcnt);
+ qib_write_kreg(dd, kr_sendpioavailaddr, dd->pioavailregs_phys);
+ val = qib_read_kreg64(dd, kr_sendpioavailaddr);
+ if (val != dd->pioavailregs_phys) {
+ qib_dev_err(dd, "Catastrophic software error, "
+ "SendPIOAvailAddr written as %lx, "
+ "read back as %llx\n",
+ (unsigned long) dd->pioavailregs_phys,
+ (unsigned long long) val);
+ ret = -EINVAL;
+ }
+ return ret;
+}
+
+static int init_6120_variables(struct qib_devdata *dd)
+{
+ int ret = 0;
+ struct qib_pportdata *ppd;
+ u32 sbufs;
+
+ ppd = (struct qib_pportdata *)(dd + 1);
+ dd->pport = ppd;
+ dd->num_pports = 1;
+
+ dd->cspec = (struct qib_chip_specific *)(ppd + dd->num_pports);
+ ppd->cpspec = NULL; /* not used in this chip */
+
+ spin_lock_init(&dd->cspec->kernel_tid_lock);
+ spin_lock_init(&dd->cspec->user_tid_lock);
+ spin_lock_init(&dd->cspec->rcvmod_lock);
+ spin_lock_init(&dd->cspec->gpio_lock);
+
+ /* we haven't yet set QIB_PRESENT, so use read directly */
+ dd->revision = readq(&dd->kregbase[kr_revision]);
+
+ if ((dd->revision & 0xffffffffU) == 0xffffffffU) {
+ qib_dev_err(dd, "Revision register read failure, "
+ "giving up initialization\n");
+ ret = -ENODEV;
+ goto bail;
+ }
+ dd->flags |= QIB_PRESENT; /* now register routines work */
+
+ dd->majrev = (u8) SYM_FIELD(dd->revision, Revision_R,
+ ChipRevMajor);
+ dd->minrev = (u8) SYM_FIELD(dd->revision, Revision_R,
+ ChipRevMinor);
+
+ get_6120_chip_params(dd);
+ pe_boardname(dd); /* fill in boardname */
+
+ /*
+ * GPIO bits for TWSI data and clock,
+ * used for serial EEPROM.
+ */
+ dd->gpio_sda_num = _QIB_GPIO_SDA_NUM;
+ dd->gpio_scl_num = _QIB_GPIO_SCL_NUM;
+ dd->twsi_eeprom_dev = QIB_TWSI_NO_DEV;
+
+ if (qib_unordered_wc())
+ dd->flags |= QIB_PIO_FLUSH_WC;
+
+ /*
+ * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
+ * 2 is Some Misc, 3 is reserved for future.
+ */
+ dd->eep_st_masks[0].hwerrs_to_log = HWE_MASK(TXEMemParityErr);
+
+ /* Ignore errors in PIO/PBC on systems with unordered write-combining */
+ if (qib_unordered_wc())
+ dd->eep_st_masks[0].hwerrs_to_log &= ~TXE_PIO_PARITY;
+
+ dd->eep_st_masks[1].hwerrs_to_log = HWE_MASK(RXEMemParityErr);
+
+ dd->eep_st_masks[2].errs_to_log = ERR_MASK(ResetNegated);
+
+ qib_init_pportdata(ppd, dd, 0, 1);
+ ppd->link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
+ ppd->link_speed_supported = QIB_IB_SDR;
+ ppd->link_width_enabled = IB_WIDTH_4X;
+ ppd->link_speed_enabled = ppd->link_speed_supported;
+ /* these can't change for this chip, so set once */
+ ppd->link_width_active = ppd->link_width_enabled;
+ ppd->link_speed_active = ppd->link_speed_enabled;
+ ppd->vls_supported = IB_VL_VL0;
+ ppd->vls_operational = ppd->vls_supported;
+
+ dd->rcvhdrentsize = QIB_RCVHDR_ENTSIZE;
+ dd->rcvhdrsize = QIB_DFLT_RCVHDRSIZE;
+ dd->rhf_offset = 0;
+
+ /* we always allocate at least 2048 bytes for eager buffers */
+ ret = ib_mtu_enum_to_int(qib_ibmtu);
+ dd->rcvegrbufsize = ret != -1 ? max(ret, 2048) : QIB_DEFAULT_MTU;
+
+ qib_6120_tidtemplate(dd);
+
+ /*
+ * We can request a receive interrupt for 1 or
+ * more packets from current offset. For now, we set this
+ * up for a single packet.
+ */
+ dd->rhdrhead_intr_off = 1ULL << 32;
+
+ /* setup the stats timer; the add_timer is done at end of init */
+ init_timer(&dd->stats_timer);
+ dd->stats_timer.function = qib_get_6120_faststats;
+ dd->stats_timer.data = (unsigned long) dd;
+
+ init_timer(&dd->cspec->pma_timer);
+ dd->cspec->pma_timer.function = pma_6120_timer;
+ dd->cspec->pma_timer.data = (unsigned long) ppd;
+
+ dd->ureg_align = qib_read_kreg32(dd, kr_palign);
+
+ dd->piosize2kmax_dwords = dd->piosize2k >> 2;
+ qib_6120_config_ctxts(dd);
+ qib_set_ctxtcnt(dd);
+
+ if (qib_wc_pat) {
+ ret = init_chip_wc_pat(dd, 0);
+ if (ret)
+ goto bail;
+ }
+ set_6120_baseaddrs(dd); /* set chip access pointers now */
+
+ ret = 0;
+ if (qib_mini_init)
+ goto bail;
+
+ qib_num_cfg_vls = 1; /* if any 6120's, only one VL */
+
+ ret = qib_create_ctxts(dd);
+ init_6120_cntrnames(dd);
+
+ /* use all of 4KB buffers for the kernel, otherwise 16 */
+ sbufs = dd->piobcnt4k ? dd->piobcnt4k : 16;
+
+ dd->lastctxt_piobuf = dd->piobcnt2k + dd->piobcnt4k - sbufs;
+ dd->pbufsctxt = dd->lastctxt_piobuf /
+ (dd->cfgctxts - dd->first_user_ctxt);
+
+ if (ret)
+ goto bail;
+bail:
+ return ret;
+}
+
+/*
+ * For this chip, we want to use the same buffer every time
+ * when we are trying to bring the link up (they are always VL15
+ * packets). At that link state the packet should always go out immediately
+ * (or at least be discarded at the tx interface if the link is down).
+ * If it doesn't, and the buffer isn't available, that means some other
+ * sender has gotten ahead of us, and is preventing our packet from going
+ * out. In that case, we flush all packets, and try again. If that still
+ * fails, we fail the request, and hope things work the next time around.
+ *
+ * We don't need very complicated heuristics on whether the packet had
+ * time to go out or not, since even at SDR 1X, it goes out in very short
+ * time periods, covered by the chip reads done here and as part of the
+ * flush.
+ */
+static u32 __iomem *get_6120_link_buf(struct qib_pportdata *ppd, u32 *bnum)
+{
+ u32 __iomem *buf;
+ u32 lbuf = ppd->dd->piobcnt2k + ppd->dd->piobcnt4k - 1;
+
+ /*
+ * always blip to get avail list updated, since it's almost
+ * always needed, and is fairly cheap.
+ */
+ sendctrl_6120_mod(ppd->dd->pport, QIB_SENDCTRL_AVAIL_BLIP);
+ qib_read_kreg64(ppd->dd, kr_scratch); /* extra chip flush */
+ buf = qib_getsendbuf_range(ppd->dd, bnum, lbuf, lbuf);
+ if (buf)
+ goto done;
+
+ sendctrl_6120_mod(ppd, QIB_SENDCTRL_DISARM_ALL | QIB_SENDCTRL_FLUSH |
+ QIB_SENDCTRL_AVAIL_BLIP);
+ ppd->dd->upd_pio_shadow = 1; /* update our idea of what's busy */
+ qib_read_kreg64(ppd->dd, kr_scratch); /* extra chip flush */
+ buf = qib_getsendbuf_range(ppd->dd, bnum, lbuf, lbuf);
+done:
+ return buf;
+}
+
+static u32 __iomem *qib_6120_getsendbuf(struct qib_pportdata *ppd, u64 pbc,
+ u32 *pbufnum)
+{
+ u32 first, last, plen = pbc & QIB_PBC_LENGTH_MASK;
+ struct qib_devdata *dd = ppd->dd;
+ u32 __iomem *buf;
+
+ if (((pbc >> 32) & PBC_6120_VL15_SEND_CTRL) &&
+ !(ppd->lflags & (QIBL_IB_AUTONEG_INPROG | QIBL_LINKACTIVE)))
+ buf = get_6120_link_buf(ppd, pbufnum);
+ else {
+
+ if ((plen + 1) > dd->piosize2kmax_dwords)
+ first = dd->piobcnt2k;
+ else
+ first = 0;
+ /* try 4k if all 2k busy, so same last for both sizes */
+ last = dd->piobcnt2k + dd->piobcnt4k - 1;
+ buf = qib_getsendbuf_range(dd, pbufnum, first, last);
+ }
+ return buf;
+}
+
+static int init_sdma_6120_regs(struct qib_pportdata *ppd)
+{
+ return -ENODEV;
+}
+
+static u16 qib_sdma_6120_gethead(struct qib_pportdata *ppd)
+{
+ return 0;
+}
+
+static int qib_sdma_6120_busy(struct qib_pportdata *ppd)
+{
+ return 0;
+}
+
+static void qib_sdma_update_6120_tail(struct qib_pportdata *ppd, u16 tail)
+{
+}
+
+static void qib_6120_sdma_sendctrl(struct qib_pportdata *ppd, unsigned op)
+{
+}
+
+static void qib_sdma_set_6120_desc_cnt(struct qib_pportdata *ppd, unsigned cnt)
+{
+}
+
+/*
+ * the pbc doesn't need a VL15 indicator, but we need it for link_buf.
+ * The chip ignores the bit if set.
+ */
+static u32 qib_6120_setpbc_control(struct qib_pportdata *ppd, u32 plen,
+ u8 srate, u8 vl)
+{
+ return vl == 15 ? PBC_6120_VL15_SEND_CTRL : 0;
+}
+
+static void qib_6120_initvl15_bufs(struct qib_devdata *dd)
+{
+}
+
+static void qib_6120_init_ctxt(struct qib_ctxtdata *rcd)
+{
+ rcd->rcvegrcnt = rcd->dd->rcvhdrcnt;
+ rcd->rcvegr_tid_base = rcd->ctxt * rcd->rcvegrcnt;
+}
+
+static void qib_6120_txchk_change(struct qib_devdata *dd, u32 start,
+ u32 len, u32 avail, struct qib_ctxtdata *rcd)
+{
+}
+
+static void writescratch(struct qib_devdata *dd, u32 val)
+{
+ (void) qib_write_kreg(dd, kr_scratch, val);
+}
+
+static int qib_6120_tempsense_rd(struct qib_devdata *dd, int regnum)
+{
+ return -ENXIO;
+}
+
+/* Dummy function, as 6120 boards never disable EEPROM Write */
+static int qib_6120_eeprom_wen(struct qib_devdata *dd, int wen)
+{
+ return 1;
+}
+
+/**
+ * qib_init_iba6120_funcs - set up the chip-specific function pointers
+ * @pdev: pci_dev of the qlogic_ib device
+ * @ent: pci_device_id matching this chip
+ *
+ * This is global, and is called directly at init to set up the
+ * chip-specific function pointers for later use.
+ *
+ * It also allocates/partially-inits the qib_devdata struct for
+ * this device.
+ */
+struct qib_devdata *qib_init_iba6120_funcs(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct qib_devdata *dd;
+ int ret;
+
+#ifndef CONFIG_PCI_MSI
+ qib_early_err(&pdev->dev, "QLogic PCIE device 0x%x cannot "
+ "work if CONFIG_PCI_MSI is not enabled\n",
+ ent->device);
+ dd = ERR_PTR(-ENODEV);
+ goto bail;
+#endif
+
+ dd = qib_alloc_devdata(pdev, sizeof(struct qib_pportdata) +
+ sizeof(struct qib_chip_specific));
+ if (IS_ERR(dd))
+ goto bail;
+
+ dd->f_bringup_serdes = qib_6120_bringup_serdes;
+ dd->f_cleanup = qib_6120_setup_cleanup;
+ dd->f_clear_tids = qib_6120_clear_tids;
+ dd->f_free_irq = qib_6120_free_irq;
+ dd->f_get_base_info = qib_6120_get_base_info;
+ dd->f_get_msgheader = qib_6120_get_msgheader;
+ dd->f_getsendbuf = qib_6120_getsendbuf;
+ dd->f_gpio_mod = gpio_6120_mod;
+ dd->f_eeprom_wen = qib_6120_eeprom_wen;
+ dd->f_hdrqempty = qib_6120_hdrqempty;
+ dd->f_ib_updown = qib_6120_ib_updown;
+ dd->f_init_ctxt = qib_6120_init_ctxt;
+ dd->f_initvl15_bufs = qib_6120_initvl15_bufs;
+ dd->f_intr_fallback = qib_6120_nointr_fallback;
+ dd->f_late_initreg = qib_late_6120_initreg;
+ dd->f_setpbc_control = qib_6120_setpbc_control;
+ dd->f_portcntr = qib_portcntr_6120;
+ dd->f_put_tid = (dd->minrev >= 2) ?
+ qib_6120_put_tid_2 :
+ qib_6120_put_tid;
+ dd->f_quiet_serdes = qib_6120_quiet_serdes;
+ dd->f_rcvctrl = rcvctrl_6120_mod;
+ dd->f_read_cntrs = qib_read_6120cntrs;
+ dd->f_read_portcntrs = qib_read_6120portcntrs;
+ dd->f_reset = qib_6120_setup_reset;
+ dd->f_init_sdma_regs = init_sdma_6120_regs;
+ dd->f_sdma_busy = qib_sdma_6120_busy;
+ dd->f_sdma_gethead = qib_sdma_6120_gethead;
+ dd->f_sdma_sendctrl = qib_6120_sdma_sendctrl;
+ dd->f_sdma_set_desc_cnt = qib_sdma_set_6120_desc_cnt;
+ dd->f_sdma_update_tail = qib_sdma_update_6120_tail;
+ dd->f_sendctrl = sendctrl_6120_mod;
+ dd->f_set_armlaunch = qib_set_6120_armlaunch;
+ dd->f_set_cntr_sample = qib_set_cntr_6120_sample;
+ dd->f_iblink_state = qib_6120_iblink_state;
+ dd->f_ibphys_portstate = qib_6120_phys_portstate;
+ dd->f_get_ib_cfg = qib_6120_get_ib_cfg;
+ dd->f_set_ib_cfg = qib_6120_set_ib_cfg;
+ dd->f_set_ib_loopback = qib_6120_set_loopback;
+ dd->f_set_intr_state = qib_6120_set_intr_state;
+ dd->f_setextled = qib_6120_setup_setextled;
+ dd->f_txchk_change = qib_6120_txchk_change;
+ dd->f_update_usrhead = qib_update_6120_usrhead;
+ dd->f_wantpiobuf_intr = qib_wantpiobuf_6120_intr;
+ dd->f_xgxs_reset = qib_6120_xgxs_reset;
+ dd->f_writescratch = writescratch;
+ dd->f_tempsense_rd = qib_6120_tempsense_rd;
+ /*
+ * Do remaining pcie setup and save pcie values in dd.
+ * Any error printing is already done by the init code.
+ * On return, we have the chip mapped and accessible,
+ * but chip registers are not set up until start of
+ * init_6120_variables.
+ */
+ ret = qib_pcie_ddinit(dd, pdev, ent);
+ if (ret < 0)
+ goto bail_free;
+
+ /* initialize chip-specific variables */
+ ret = init_6120_variables(dd);
+ if (ret)
+ goto bail_cleanup;
+
+ if (qib_mini_init)
+ goto bail;
+
+#ifndef CONFIG_PCI_MSI
+ qib_dev_err(dd, "PCI_MSI not configured, NO interrupts\n");
+#endif
+
+ if (qib_pcie_params(dd, 8, NULL, NULL))
+ qib_dev_err(dd, "Failed to setup PCIe or interrupts; "
+ "continuing anyway\n");
+ dd->cspec->irq = pdev->irq; /* save IRQ */
+
+ /* clear diagctrl register, in case diags were running and crashed */
+ qib_write_kreg(dd, kr_hwdiagctrl, 0);
+
+ if (qib_read_kreg64(dd, kr_hwerrstatus) &
+ QLOGIC_IB_HWE_SERDESPLLFAILED)
+ qib_write_kreg(dd, kr_hwerrclear,
+ QLOGIC_IB_HWE_SERDESPLLFAILED);
+
+ /* setup interrupt handler (interrupt type handled above) */
+ qib_setup_6120_interrupt(dd);
+ /* Note that qpn_mask is set by qib_6120_config_ctxts() first */
+ qib_6120_init_hwerrors(dd);
+
+ goto bail;
+
+bail_cleanup:
+ qib_pcie_ddcleanup(dd);
+bail_free:
+ qib_free_devdata(dd);
+ dd = ERR_PTR(ret);
+bail:
+ return dd;
+}