[PATCH] libata: add 40pin "short" cable support, honour drive side speed detection
[deweerdt@free.fr: build fix]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Frederik Deweerdt <deweerdt@free.fr>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 720174d..14b726b 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -93,7 +93,7 @@
#include <linux/libata.h>
#define DRV_NAME "ata_piix"
-#define DRV_VERSION "2.00ac6"
+#define DRV_VERSION "2.00ac7"
enum {
PIIX_IOCFG = 0x54, /* IDE I/O configuration register */
@@ -571,6 +571,23 @@
MODULE_PARM_DESC(force_pcs, "force honoring or ignoring PCS to work around "
"device mis-detection (0=default, 1=ignore PCS, 2=honor PCS)");
+struct ich_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+/*
+ * List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x27DF, 0x0005, 0x0280 }, /* ICH7 on Acer 5602WLMi */
+ /* end marker */
+ { 0, }
+};
+
/**
* piix_pata_cbl_detect - Probe host controller cable detect info
* @ap: Port for which cable detect info is desired
@@ -585,12 +602,24 @@
static void ich_pata_cbl_detect(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ const struct ich_laptop *lap = &ich_laptop[0];
u8 tmp, mask;
/* no 80c support in host controller? */
if ((ap->udma_mask & ~ATA_UDMA_MASK_40C) == 0)
goto cbl40;
+ /* Check for specials - Acer Aspire 5602WLMi */
+ while (lap->device) {
+ if (lap->device == pdev->device &&
+ lap->subvendor == pdev->subsystem_vendor &&
+ lap->subdevice == pdev->subsystem_device) {
+ ap->cbl = ATA_CBL_PATA40_SHORT;
+ return;
+ }
+ lap++;
+ }
+
/* check BIOS cable detect results */
mask = ap->port_no == 0 ? PIIX_80C_PRI : PIIX_80C_SEC;
pci_read_config_byte(pdev, PIIX_IOCFG, &tmp);
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 915a55a..b896119 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3119,6 +3119,13 @@
*/
if (ap->cbl == ATA_CBL_PATA40)
xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
+ /* Apply drive side cable rule. Unknown or 80 pin cables reported
+ * host side are checked drive side as well. Cases where we know a
+ * 40wire cable is used safely for 80 are not checked here.
+ */
+ if (ata_drive_40wire(dev->id) && (ap->cbl == ATA_CBL_PATA_UNK || ap->cbl == ATA_CBL_PATA80))
+ xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
+
xfer_mask &= ata_pack_xfermask(dev->pio_mask,
dev->mwdma_mask, dev->udma_mask);
diff --git a/drivers/ata/pata_ali.c b/drivers/ata/pata_ali.c
index 64eed99..e6d2b84 100644
--- a/drivers/ata/pata_ali.c
+++ b/drivers/ata/pata_ali.c
@@ -78,7 +78,7 @@
implement the detect logic */
if (ali_cable_override(pdev))
- return ATA_CBL_PATA80;
+ return ATA_CBL_PATA40_SHORT;
/* Host view cable detect 0x4A bit 0 primary bit 1 secondary
Bit set for 40 pin */
diff --git a/include/linux/ata.h b/include/linux/ata.h
index d894419..1df9416 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -200,8 +200,9 @@
ATA_CBL_NONE = 0,
ATA_CBL_PATA40 = 1,
ATA_CBL_PATA80 = 2,
- ATA_CBL_PATA_UNK = 3,
- ATA_CBL_SATA = 4,
+ ATA_CBL_PATA40_SHORT = 3, /* 40 wire cable to high UDMA spec */
+ ATA_CBL_PATA_UNK = 4,
+ ATA_CBL_SATA = 5,
/* SATA Status and Control Registers */
SCR_STATUS = 0,
@@ -342,6 +343,15 @@
return 0;
}
+static inline int ata_drive_40wire(const u16 *dev_id)
+{
+ if (ata_id_major_version(dev_id) >= 5 && ata_id_is_sata(dev_id))
+ return 0; /* SATA */
+ if (dev_id[93] & 0x4000)
+ return 0; /* 80 wire */
+ return 1;
+}
+
static inline int atapi_cdb_len(const u16 *dev_id)
{
u16 tmp = dev_id[0] & 0x3;