blob: 45579ae12c01e887a7bca3f82e6a0769155dec73 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# IDE ATA ATAPI Block device driver configuration
3#
4# Andre Hedrick <andre@linux-ide.org>
5#
6
7menu "ATA/ATAPI/MFM/RLL support"
8
9config IDE
10 tristate "ATA/ATAPI/MFM/RLL support"
11 ---help---
12 If you say Y here, your kernel will be able to manage low cost mass
13 storage units such as ATA/(E)IDE and ATAPI units. The most common
14 cases are IDE hard drives and ATAPI CD-ROM drives.
15
16 If your system is pure SCSI and doesn't use these interfaces, you
17 can say N here.
18
19 Integrated Disk Electronics (IDE aka ATA-1) is a connecting standard
20 for mass storage units such as hard disks. It was designed by
21 Western Digital and Compaq Computer in 1984. It was then named
22 ST506. Quite a number of disks use the IDE interface.
23
24 AT Attachment (ATA) is the superset of the IDE specifications.
25 ST506 was also called ATA-1.
26
27 Fast-IDE is ATA-2 (also named Fast ATA), Enhanced IDE (EIDE) is
28 ATA-3. It provides support for larger disks (up to 8.4GB by means of
29 the LBA standard), more disks (4 instead of 2) and for other mass
30 storage units such as tapes and cdrom. UDMA/33 (aka UltraDMA/33) is
31 ATA-4 and provides faster (and more CPU friendly) transfer modes
32 than previous PIO (Programmed processor Input/Output) from previous
33 ATA/IDE standards by means of fast DMA controllers.
34
35 ATA Packet Interface (ATAPI) is a protocol used by EIDE tape and
36 CD-ROM drives, similar in many respects to the SCSI protocol.
37
38 SMART IDE (Self Monitoring, Analysis and Reporting Technology) was
39 designed in order to prevent data corruption and disk crash by
40 detecting pre hardware failure conditions (heat, access time, and
41 the like...). Disks built since June 1995 may follow this standard.
42 The kernel itself doesn't manage this; however there are quite a
43 number of user programs such as smart that can query the status of
44 SMART parameters from disk drives.
45
46 To compile this driver as a module, choose M here: the
47 module will be called ide.
48
49 For further information, please read <file:Documentation/ide.txt>.
50
51 If unsure, say Y.
52
53if IDE
54
55config IDE_MAX_HWIFS
56 int "Max IDE interfaces"
57 depends on ALPHA || SUPERH
58 default 4
59 help
60 This is the maximum number of IDE hardware interfaces that will
61 be supported by the driver. Make sure it is at least as high as
62 the number of IDE interfaces in your system.
63
64config BLK_DEV_IDE
65 tristate "Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support"
66 ---help---
67 If you say Y here, you will use the full-featured IDE driver to
68 control up to ten ATA/IDE interfaces, each being able to serve a
69 "master" and a "slave" device, for a total of up to twenty ATA/IDE
70 disk/cdrom/tape/floppy drives.
71
72 Useful information about large (>540 MB) IDE disks, multiple
73 interfaces, what to do if ATA/IDE devices are not automatically
74 detected, sound card ATA/IDE ports, module support, and other
75 topics, is contained in <file:Documentation/ide.txt>. For detailed
76 information about hard drives, consult the Disk-HOWTO and the
77 Multi-Disk-HOWTO, available from
78 <http://www.tldp.org/docs.html#howto>.
79
80 To fine-tune ATA/IDE drive/interface parameters for improved
81 performance, look for the hdparm package at
82 <ftp://ibiblio.org/pub/Linux/system/hardware/>.
83
84 To compile this driver as a module, choose M here and read
85 <file:Documentation/ide.txt>. The module will be called ide-mod.
86 Do not compile this driver as a module if your root file system (the
87 one containing the directory /) is located on an IDE device.
88
89 If you have one or more IDE drives, say Y or M here. If your system
90 has no IDE drives, or if memory requirements are really tight, you
91 could say N here, and select the "Old hard disk driver" below
92 instead to save about 13 KB of memory in the kernel.
93
94if BLK_DEV_IDE
95
96comment "Please see Documentation/ide.txt for help/info on IDE drives"
97
98config BLK_DEV_IDE_SATA
99 bool "Support for SATA (deprecated; conflicts with libata SATA driver)"
100 default n
101 ---help---
102 There are two drivers for Serial ATA controllers.
103
104 The main driver, "libata", exists inside the SCSI subsystem
105 and supports most modern SATA controllers.
106
107 The IDE driver (which you are currently configuring) supports
108 a few first-generation SATA controllers.
109
110 In order to eliminate conflicts between the two subsystems,
111 this config option enables the IDE driver's SATA support.
112 Normally this is disabled, as it is preferred that libata
113 supports SATA controllers, and this (IDE) driver supports
114 PATA controllers.
115
116 If unsure, say N.
117
118config BLK_DEV_HD_IDE
119 bool "Use old disk-only driver on primary interface"
120 depends on (X86 || SH_MPC1211)
121 ---help---
122 There are two drivers for MFM/RLL/IDE disks. Most people use just
123 the new enhanced driver by itself. This option however installs the
124 old hard disk driver to control the primary IDE/disk interface in
125 the system, leaving the new enhanced IDE driver to take care of only
126 the 2nd/3rd/4th IDE interfaces. Doing this will prevent you from
127 having an IDE/ATAPI CD-ROM or tape drive connected to the primary
128 IDE interface. Choosing this option may be useful for older systems
129 which have MFM/RLL/ESDI controller+drives at the primary port
130 address (0x1f0), along with IDE drives at the secondary/3rd/4th port
131 addresses.
132
133 Normally, just say N here; you will then use the new driver for all
134 4 interfaces.
135
136config BLK_DEV_IDEDISK
137 tristate "Include IDE/ATA-2 DISK support"
138 ---help---
139 This will include enhanced support for MFM/RLL/IDE hard disks. If
140 you have a MFM/RLL/IDE disk, and there is no special reason to use
141 the old hard disk driver instead, say Y. If you have an SCSI-only
142 system, you can say N here.
143
144 To compile this driver as a module, choose M here: the
145 module will be called ide-disk.
146 Do not compile this driver as a module if your root file system
147 (the one containing the directory /) is located on the IDE disk.
148
149 If unsure, say Y.
150
151config IDEDISK_MULTI_MODE
152 bool "Use multi-mode by default"
153 help
154 If you get this error, try to say Y here:
155
156 hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
157 hda: set_multmode: error=0x04 { DriveStatusError }
158
159 If in doubt, say N.
160
161config BLK_DEV_IDECS
162 tristate "PCMCIA IDE support"
163 depends on PCMCIA
164 help
165 Support for outboard IDE disks, tape drives, and CD-ROM drives
166 connected through a PCMCIA card.
167
168config BLK_DEV_IDECD
169 tristate "Include IDE/ATAPI CDROM support"
170 ---help---
171 If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is
172 a newer protocol used by IDE CD-ROM and TAPE drives, similar to the
173 SCSI protocol. Most new CD-ROM drives use ATAPI, including the
174 NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI
175 double(2X) or better speed drives.
176
177 If you say Y here, the CD-ROM drive will be identified at boot time
178 along with other IDE devices, as "hdb" or "hdc", or something
179 similar (check the boot messages with dmesg). If this is your only
180 CD-ROM drive, you can say N to all other CD-ROM options, but be sure
181 to say Y or M to "ISO 9660 CD-ROM file system support".
182
183 Note that older versions of LILO (LInux LOader) cannot properly deal
184 with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from
185 <http://lilo.go.dyndns.org/>.
186
187 To compile this driver as a module, choose M here: the
188 module will be called ide-cd.
189
190config BLK_DEV_IDETAPE
191 tristate "Include IDE/ATAPI TAPE support (EXPERIMENTAL)"
192 depends on EXPERIMENTAL
193 help
194 If you have an IDE tape drive using the ATAPI protocol, say Y.
195 ATAPI is a newer protocol used by IDE tape and CD-ROM drives,
196 similar to the SCSI protocol. If you have an SCSI tape drive
197 however, you can say N here.
198
199 You should also say Y if you have an OnStream DI-30 tape drive; this
200 will not work with the SCSI protocol, until there is support for the
201 SC-30 and SC-50 versions.
202
203 If you say Y here, the tape drive will be identified at boot time
204 along with other IDE devices, as "hdb" or "hdc", or something
205 similar, and will be mapped to a character device such as "ht0"
206 (check the boot messages with dmesg). Be sure to consult the
207 <file:drivers/ide/ide-tape.c> and <file:Documentation/ide.txt> files
208 for usage information.
209
210 To compile this driver as a module, choose M here: the
211 module will be called ide-tape.
212
213config BLK_DEV_IDEFLOPPY
214 tristate "Include IDE/ATAPI FLOPPY support"
215 ---help---
216 If you have an IDE floppy drive which uses the ATAPI protocol,
217 answer Y. ATAPI is a newer protocol used by IDE CD-ROM/tape/floppy
218 drives, similar to the SCSI protocol.
219
220 The LS-120 and the IDE/ATAPI Iomega ZIP drive are also supported by
221 this driver. For information about jumper settings and the question
222 of when a ZIP drive uses a partition table, see
223 <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>.
224 (ATAPI PD-CD/CDR drives are not supported by this driver; support
225 for PD-CD/CDR drives is available if you answer Y to
226 "SCSI emulation support", below).
227
228 If you say Y here, the FLOPPY drive will be identified along with
229 other IDE devices, as "hdb" or "hdc", or something similar (check
230 the boot messages with dmesg).
231
232 To compile this driver as a module, choose M here: the
233 module will be called ide-floppy.
234
235config BLK_DEV_IDESCSI
236 tristate "SCSI emulation support"
237 depends on SCSI
238 ---help---
239 WARNING: ide-scsi is no longer needed for cd writing applications!
240 The 2.6 kernel supports direct writing to ide-cd, which eliminates
241 the need for ide-scsi + the entire scsi stack just for writing a
242 cd. The new method is more efficient in every way.
243
244 This will provide SCSI host adapter emulation for IDE ATAPI devices,
245 and will allow you to use a SCSI device driver instead of a native
246 ATAPI driver.
247
248 This is useful if you have an ATAPI device for which no native
249 driver has been written (for example, an ATAPI PD-CD drive);
250 you can then use this emulation together with an appropriate SCSI
251 device driver. In order to do this, say Y here and to "SCSI support"
252 and "SCSI generic support", below. You must then provide the kernel
253 command line "hdx=ide-scsi" (try "man bootparam" or see the
254 documentation of your boot loader (lilo or loadlin) about how to
255 pass options to the kernel at boot time) for devices if you want the
256 native EIDE sub-drivers to skip over the native support, so that
257 this SCSI emulation can be used instead.
258
259 Note that this option does NOT allow you to attach SCSI devices to a
260 box that doesn't have a SCSI host adapter installed.
261
262 If both this SCSI emulation and native ATAPI support are compiled
263 into the kernel, the native support will be used.
264
265config IDE_TASK_IOCTL
266 bool "IDE Taskfile Access"
267 help
268 This is a direct raw access to the media. It is a complex but
269 elegant solution to test and validate the domain of the hardware and
270 perform below the driver data recover if needed. This is the most
271 basic form of media-forensics.
272
273 If you are unsure, say N here.
274
275comment "IDE chipset support/bugfixes"
276
277config IDE_GENERIC
278 tristate "generic/default IDE chipset support"
279 default y
280 help
281 If unsure, say Y.
282
283config BLK_DEV_CMD640
284 bool "CMD640 chipset bugfix/support"
285 depends on X86
286 ---help---
287 The CMD-Technologies CMD640 IDE chip is used on many common 486 and
288 Pentium motherboards, usually in combination with a "Neptune" or
289 "SiS" chipset. Unfortunately, it has a number of rather nasty
290 design flaws that can cause severe data corruption under many common
291 conditions. Say Y here to include code which tries to automatically
292 detect and correct the problems under Linux. This option also
293 enables access to the secondary IDE ports in some CMD640 based
294 systems.
295
296 This driver will work automatically in PCI based systems (most new
297 systems have PCI slots). But if your system uses VESA local bus
298 (VLB) instead of PCI, you must also supply a kernel boot parameter
299 to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man
300 bootparam" or see the documentation of your boot loader about how to
301 pass options to the kernel.)
302
303 The CMD640 chip is also used on add-in cards by Acculogic, and on
304 the "CSA-6400E PCI to IDE controller" that some people have. For
305 details, read <file:Documentation/ide.txt>.
306
307config BLK_DEV_CMD640_ENHANCED
308 bool "CMD640 enhanced support"
309 depends on BLK_DEV_CMD640
310 help
311 This option includes support for setting/autotuning PIO modes and
312 prefetch on CMD640 IDE interfaces. For details, read
313 <file:Documentation/ide.txt>. If you have a CMD640 IDE interface
314 and your BIOS does not already do this for you, then say Y here.
315 Otherwise say N.
316
317config BLK_DEV_IDEPNP
318 bool "PNP EIDE support"
319 depends on PNP
320 help
321 If you have a PnP (Plug and Play) compatible EIDE card and
322 would like the kernel to automatically detect and activate
323 it, say Y here.
324
325config BLK_DEV_IDEPCI
326 bool "PCI IDE chipset support" if PCI
327 default BLK_DEV_IDEDMA_PMAC if PPC_PMAC && BLK_DEV_IDEDMA_PMAC
328 help
329 Say Y here for PCI systems which use IDE drive(s).
330 This option helps the IDE driver to automatically detect and
331 configure all PCI-based IDE interfaces in your system.
332
333config IDEPCI_SHARE_IRQ
334 bool "Sharing PCI IDE interrupts support"
335 depends on PCI && BLK_DEV_IDEPCI
336 help
337 Some ATA/IDE chipsets have hardware support which allows for
338 sharing a single IRQ with other cards. To enable support for
339 this in the ATA/IDE driver, say Y here.
340
341 It is safe to say Y to this question, in most cases.
342 If unsure, say N.
343
344config BLK_DEV_OFFBOARD
345 bool "Boot off-board chipsets first support"
346 depends on PCI && BLK_DEV_IDEPCI
347 help
348 Normally, IDE controllers built into the motherboard (on-board
349 controllers) are assigned to ide0 and ide1 while those on add-in PCI
350 cards (off-board controllers) are relegated to ide2 and ide3.
351 Answering Y here will allow you to reverse the situation, with
352 off-board controllers on ide0/1 and on-board controllers on ide2/3.
353 This can improve the usability of some boot managers such as lilo
354 when booting from a drive on an off-board controller.
355
356 If you say Y here, and you actually want to reverse the device scan
357 order as explained above, you also need to issue the kernel command
358 line option "ide=reverse". (Try "man bootparam" or see the
359 documentation of your boot loader (lilo or loadlin) about how to
360 pass options to the kernel at boot time.)
361
362 Note that, if you do this, the order of the hd* devices will be
363 rearranged which may require modification of fstab and other files.
364
365 If in doubt, say N.
366
367config BLK_DEV_GENERIC
368 tristate "Generic PCI IDE Chipset Support"
369 depends on BLK_DEV_IDEPCI
370
371config BLK_DEV_OPTI621
372 tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
373 depends on PCI && BLK_DEV_IDEPCI && EXPERIMENTAL
374 help
375 This is a driver for the OPTi 82C621 EIDE controller.
376 Please read the comments at the top of <file:drivers/ide/pci/opti621.c>.
377
378config BLK_DEV_RZ1000
379 tristate "RZ1000 chipset bugfix/support"
380 depends on PCI && BLK_DEV_IDEPCI && X86
381 help
382 The PC-Technologies RZ1000 IDE chip is used on many common 486 and
383 Pentium motherboards, usually along with the "Neptune" chipset.
384 Unfortunately, it has a rather nasty design flaw that can cause
385 severe data corruption under many conditions. Say Y here to include
386 code which automatically detects and corrects the problem under
387 Linux. This may slow disk throughput by a few percent, but at least
388 things will operate 100% reliably.
389
390config BLK_DEV_SL82C105
391 tristate "Winbond SL82c105 support"
392 depends on PCI && (PPC || ARM) && BLK_DEV_IDEPCI
393 help
394 If you have a Winbond SL82c105 IDE controller, say Y here to enable
395 special configuration for this chip. This is common on various CHRP
396 motherboards, but could be used elsewhere. If in doubt, say Y.
397
398config BLK_DEV_IDEDMA_PCI
399 bool "Generic PCI bus-master DMA support"
400 depends on PCI && BLK_DEV_IDEPCI
401 ---help---
402 If your PCI system uses IDE drive(s) (as opposed to SCSI, say) and
403 is capable of bus-master DMA operation (most Pentium PCI systems),
404 you will want to say Y here to reduce CPU overhead. You can then use
405 the "hdparm" utility to enable DMA for drives for which it was not
406 enabled automatically. By default, DMA is not enabled automatically
407 for these drives, but you can change that by saying Y to the
408 following question "Use DMA by default when available". You can get
409 the latest version of the hdparm utility from
410 <ftp://ibiblio.org/pub/Linux/system/hardware/>.
411
412 Read the comments at the beginning of <file:drivers/ide/ide-dma.c>
413 and the file <file:Documentation/ide.txt> for more information.
414
415 It is safe to say Y to this question.
416
417if BLK_DEV_IDEDMA_PCI
418
419config BLK_DEV_IDEDMA_FORCED
420 bool "Force enable legacy 2.0.X HOSTS to use DMA"
421 help
422 This is an old piece of lost code from Linux 2.0 Kernels.
423
424 Generally say N here.
425
426config IDEDMA_PCI_AUTO
427 bool "Use PCI DMA by default when available"
428 ---help---
429 Prior to kernel version 2.1.112, Linux used to automatically use
430 DMA for IDE drives and chipsets which support it. Due to concerns
431 about a couple of cases where buggy hardware may have caused damage,
432 the default is now to NOT use DMA automatically. To revert to the
433 previous behaviour, say Y to this question.
434
435 If you suspect your hardware is at all flakey, say N here.
436 Do NOT email the IDE kernel people regarding this issue!
437
438 It is normally safe to answer Y to this question unless your
439 motherboard uses a VIA VP2 chipset, in which case you should say N.
440
441config IDEDMA_ONLYDISK
442 bool "Enable DMA only for disks "
443 depends on IDEDMA_PCI_AUTO
444 help
445 This is used if you know your ATAPI Devices are going to fail DMA
446 Transfers.
447
448 Generally say N here.
449
450config BLK_DEV_AEC62XX
451 tristate "AEC62XX chipset support"
452 help
453 This driver adds explicit support for Acard AEC62xx (Artop ATP8xx)
454 IDE controllers. This allows the kernel to change PIO, DMA and UDMA
455 speeds and to configure the chip to optimum performance.
456
457config BLK_DEV_ALI15X3
458 tristate "ALI M15x3 chipset support"
459 help
460 This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C
461 onboard chipsets. It also tests for Simplex mode and enables
462 normal dual channel support.
463
464 If you say Y here, you also need to say Y to "Use DMA by default
465 when available", above. Please read the comments at the top of
466 <file:drivers/ide/pci/alim15x3.c>.
467
468 If unsure, say N.
469
470config WDC_ALI15X3
471 bool "ALI M15x3 WDC support (DANGEROUS)"
472 depends on BLK_DEV_ALI15X3
473 ---help---
474 This allows for UltraDMA support for WDC drives that ignore CRC
475 checking. You are a fool for enabling this option, but there have
476 been requests. DO NOT COMPLAIN IF YOUR DRIVE HAS FS CORRUPTION, IF
477 YOU ENABLE THIS! No one will listen, just laugh for ignoring this
478 SERIOUS WARNING.
479
480 Using this option can allow WDC drives to run at ATA-4/5 transfer
481 rates with only an ATA-2 support structure.
482
483 SAY N!
484
485config BLK_DEV_AMD74XX
486 tristate "AMD and nVidia IDE support"
487 help
488 This driver adds explicit support for AMD-7xx and AMD-8111 chips
489 and also for the nVidia nForce chip. This allows the kernel to
490 change PIO, DMA and UDMA speeds and to configure the chip to
491 optimum performance.
492
493config BLK_DEV_ATIIXP
494 tristate "ATI IXP chipset IDE support"
495 depends on X86
496 help
497 This driver adds explicit support for ATI IXP chipset.
498 This allows the kernel to change PIO, DMA and UDMA speeds
499 and to configure the chip to optimum performance.
500
501 Say Y here if you have an ATI IXP chipset IDE controller.
502
503config BLK_DEV_CMD64X
504 tristate "CMD64{3|6|8|9} chipset support"
505 help
506 Say Y here if you have an IDE controller which uses any of these
507 chipsets: CMD643, CMD646, or CMD648.
508
509config BLK_DEV_TRIFLEX
510 tristate "Compaq Triflex IDE support"
511 help
512 Say Y here if you have a Compaq Triflex IDE controller, such
513 as those commonly found on Compaq Pentium-Pro systems
514
515config BLK_DEV_CY82C693
516 tristate "CY82C693 chipset support"
517 help
518 This driver adds detection and support for the CY82C693 chipset
519 used on Digital's PC-Alpha 164SX boards.
520
521 If you say Y here, you need to say Y to "Use DMA by default
522 when available" as well.
523
524config BLK_DEV_CS5520
525 tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
526 depends on EXPERIMENTAL
527 help
528 Include support for PIO tuning an virtual DMA on the Cyrix MediaGX
529 5510/5520 chipset. This will automatically be detected and
530 configured if found.
531
532 It is safe to say Y to this question.
533
534config BLK_DEV_CS5530
535 tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support"
536 help
537 Include support for UDMA on the Cyrix MediaGX 5530 chipset. This
538 will automatically be detected and configured if found.
539
540 It is safe to say Y to this question.
541
Jaya Kumarf5b2d8b2005-11-09 23:58:16 +0100542config BLK_DEV_CS5535
543 tristate "AMD CS5535 chipset support"
544 depends on X86 && !X86_64
545 help
546 Include support for UDMA on the NSC/AMD CS5535 companion chipset.
547 This will automatically be detected and configured if found.
548
549 It is safe to say Y to this question.
550
Linus Torvalds1da177e2005-04-16 15:20:36 -0700551config BLK_DEV_HPT34X
552 tristate "HPT34X chipset support"
553 help
554 This driver adds up to 4 more EIDE devices sharing a single
555 interrupt. The HPT343 chipset in its current form is a non-bootable
556 controller; the HPT345/HPT363 chipset is a bootable (needs BIOS FIX)
557 PCI UDMA controllers. This driver requires dynamic tuning of the
558 chipset during the ide-probe at boot time. It is reported to support
559 DVD II drives, by the manufacturer.
560
561config HPT34X_AUTODMA
562 bool "HPT34X AUTODMA support (EXPERIMENTAL)"
563 depends on BLK_DEV_HPT34X && EXPERIMENTAL
564 help
565 This is a dangerous thing to attempt currently! Please read the
566 comments at the top of <file:drivers/ide/pci/hpt34x.c>. If you say Y
567 here, then say Y to "Use DMA by default when available" as well.
568
569 If unsure, say N.
570
571config BLK_DEV_HPT366
572 tristate "HPT36X/37X chipset support"
573 ---help---
574 HPT366 is an Ultra DMA chipset for ATA-66.
575 HPT368 is an Ultra DMA chipset for ATA-66 RAID Based.
576 HPT370 is an Ultra DMA chipset for ATA-100.
577 HPT372 is an Ultra DMA chipset for ATA-100.
578 HPT374 is an Ultra DMA chipset for ATA-100.
579
580 This driver adds up to 4 more EIDE devices sharing a single
581 interrupt.
582
583 The HPT366 chipset in its current form is bootable. One solution
584 for this problem are special LILO commands for redirecting the
585 reference to device 0x80. The other solution is to say Y to "Boot
586 off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless
587 your mother board has the chipset natively mounted. Regardless one
588 should use the fore mentioned option and call at LILO or include
589 "ide=reverse" in LILO's append-line.
590
591 This driver requires dynamic tuning of the chipset during the
592 ide-probe at boot. It is reported to support DVD II drives, by the
593 manufacturer.
594
595config BLK_DEV_SC1200
596 tristate "National SCx200 chipset support"
597 help
598 This driver adds support for the built in IDE on the National
599 SCx200 series of embedded x86 "Geode" systems
600
601config BLK_DEV_PIIX
602 tristate "Intel PIIXn chipsets support"
603 help
604 This driver adds explicit support for Intel PIIX and ICH chips
605 and also for the Efar Victory66 (slc90e66) chip. This allows
606 the kernel to change PIO, DMA and UDMA speeds and to configure
607 the chip to optimum performance.
608
609config BLK_DEV_IT8172
610 bool "IT8172 IDE support"
611 depends on (MIPS_ITE8172 || MIPS_IVR)
612 help
613 Say Y here to support the on-board IDE controller on the Integrated
614 Technology Express, Inc. ITE8172 SBC. Vendor page at
615 <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
616 board at <http://www.mvista.com/partners/semiconductor/ite.html>.
617
Alan Coxda9091e2005-06-27 15:24:30 -0700618config BLK_DEV_IT821X
619 tristate "IT821X IDE support"
620 help
621 This driver adds support for the ITE 8211 IDE controller and the
622 IT 8212 IDE RAID controller in both RAID and pass-through mode.
623
Linus Torvalds1da177e2005-04-16 15:20:36 -0700624config BLK_DEV_NS87415
625 tristate "NS87415 chipset support"
626 help
627 This driver adds detection and support for the NS87415 chip
Matthew Wilcox41df8942005-11-18 16:18:40 -0500628 (used mainly on SPARC64 and PA-RISC machines).
Linus Torvalds1da177e2005-04-16 15:20:36 -0700629
630 Please read the comments at the top of <file:drivers/ide/pci/ns87415.c>.
631
632config BLK_DEV_PDC202XX_OLD
633 tristate "PROMISE PDC202{46|62|65|67} support"
634 help
635 Promise Ultra33 or PDC20246
636 Promise Ultra66 or PDC20262
637 Promise Ultra100 or PDC20265/PDC20267/PDC20268
638
639 This driver adds up to 4 more EIDE devices sharing a single
640 interrupt. This add-on card is a bootable PCI UDMA controller. Since
641 multiple cards can be installed and there are BIOS ROM problems that
642 happen if the BIOS revisions of all installed cards (three-max) do
643 not match, the driver attempts to do dynamic tuning of the chipset
644 at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
645 for more than one card. This card may require that you say Y to
646 "Special UDMA Feature".
647
648 If you say Y here, you need to say Y to "Use DMA by default when
649 available" as well.
650
651 Please read the comments at the top of
652 <file:drivers/ide/pci/pdc202xx_old.c>.
653
654 If unsure, say N.
655
656config PDC202XX_BURST
657 bool "Special UDMA Feature"
658 depends on BLK_DEV_PDC202XX_OLD
659 help
660 This option causes the pdc202xx driver to enable UDMA modes on the
661 PDC202xx even when the PDC202xx BIOS has not done so.
662
663 It was originally designed for the PDC20246/Ultra33, whose BIOS will
664 only setup UDMA on the first two PDC20246 cards. It has also been
665 used succesfully on a PDC20265/Ultra100, allowing use of UDMA modes
666 when the PDC20265 BIOS has been disabled (for faster boot up).
667
668 Please read the comments at the top of
669 <file:drivers/ide/pci/pdc202xx_old.c>.
670
671 If unsure, say N.
672
673config BLK_DEV_PDC202XX_NEW
674 tristate "PROMISE PDC202{68|69|70|71|75|76|77} support"
675
676# FIXME - probably wants to be one for old and for new
677config PDC202XX_FORCE
678 bool "Enable controller even if disabled by BIOS"
679 depends on BLK_DEV_PDC202XX_NEW
680 help
681 Enable the PDC202xx controller even if it has been disabled in the BIOS setup.
682
683config BLK_DEV_SVWKS
684 tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support"
685 help
686 This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5
687 chipsets.
688
689config BLK_DEV_SGIIOC4
Brent Casavante5d310b2005-06-21 17:16:01 -0700690 tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
691 depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
Linus Torvalds1da177e2005-04-16 15:20:36 -0700692 help
693 This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
694 chipset, which has one channel and can support two devices.
695 Please say Y here if you have an Altix System from SGI.
696
697config BLK_DEV_SIIMAGE
698 tristate "Silicon Image chipset support"
699 help
700 This driver adds PIO/(U)DMA support for the SI CMD680 and SII
701 3112 (Serial ATA) chips.
702
703config BLK_DEV_SIS5513
704 tristate "SiS5513 chipset support"
705 depends on X86
706 ---help---
707 This driver ensures (U)DMA support for SIS5513 chipset family based
708 mainboards.
709
710 The following chipsets are supported:
711 ATA16: SiS5511, SiS5513
712 ATA33: SiS5591, SiS5597, SiS5598, SiS5600
713 ATA66: SiS530, SiS540, SiS620, SiS630, SiS640
714 ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
715 SiS745, SiS750
716
717 If you say Y here, you need to say Y to "Use DMA by default when
718 available" as well.
719
720 Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
721
722config BLK_DEV_SLC90E66
723 tristate "SLC90E66 chipset support"
724 help
725 This driver ensures (U)DMA support for Victroy66 SouthBridges for
726 SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
727 The nice thing about it is that you can mix Ultra/DMA/PIO devices
728 and it will handle timing cycles. Since this is an improved
729 look-a-like to the PIIX4 it should be a nice addition.
730
731 If you say Y here, you need to say Y to "Use DMA by default when
732 available" as well.
733
734 Please read the comments at the top of
735 <file:drivers/ide/pci/slc90e66.c>.
736
737config BLK_DEV_TRM290
738 tristate "Tekram TRM290 chipset support"
739 help
740 This driver adds support for bus master DMA transfers
741 using the Tekram TRM290 PCI IDE chip. Volunteers are
742 needed for further tweaking and development.
743 Please read the comments at the top of <file:drivers/ide/pci/trm290.c>.
744
745config BLK_DEV_VIA82CXXX
746 tristate "VIA82CXXX chipset support"
747 help
748 This driver adds explicit support for VIA BusMastering IDE chips.
749 This allows the kernel to change PIO, DMA and UDMA speeds and to
750 configure the chip to optimum performance.
751
752endif
753
754config BLK_DEV_IDE_PMAC
755 bool "Builtin PowerMac IDE support"
756 depends on PPC_PMAC && IDE=y
757 help
758 This driver provides support for the built-in IDE controller on
759 most of the recent Apple Power Macintoshes and PowerBooks.
760 If unsure, say Y.
761
762config BLK_DEV_IDE_PMAC_ATA100FIRST
763 bool "Probe internal ATA/100 (Kauai) first"
764 depends on BLK_DEV_IDE_PMAC
765 help
766 This option will cause the ATA/100 controller found in UniNorth2
767 based machines (Windtunnel PowerMac, Aluminium PowerBooks, ...)
768 to be probed before the ATA/66 and ATA/33 controllers. Without
769 these, those machine used to have the hard disk on hdc and the
770 CD-ROM on hda. This option changes this to more natural hda for
771 hard disk and hdc for CD-ROM.
772
773config BLK_DEV_IDEDMA_PMAC
774 bool "PowerMac IDE DMA support"
775 depends on BLK_DEV_IDE_PMAC
Juha-Matti Tapio0ac72b32005-08-18 22:13:44 +0200776 select BLK_DEV_IDEDMA_PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700777 help
778 This option allows the driver for the built-in IDE controller on
779 Power Macintoshes and PowerBooks to use DMA (direct memory access)
780 to transfer data to and from memory. Saying Y is safe and improves
781 performance.
782
783config BLK_DEV_IDE_PMAC_BLINK
784 bool "Blink laptop LED on drive activity"
785 depends on BLK_DEV_IDE_PMAC && ADB_PMU
786 help
787 This option enables the use of the sleep LED as a hard drive
788 activity LED.
789
Ralf Baechle4237f222005-11-17 16:23:50 +0000790config BLK_DEV_IDE_SWARM
791 tristate "IDE for Sibyte evaluation boards"
792 depends on SIBYTE_SB1xxx_SOC
793
Pete Popov26a940e2005-09-15 08:03:12 +0000794config BLK_DEV_IDE_AU1XXX
795 bool "IDE for AMD Alchemy Au1200"
796 depends on SOC_AU1200
797choice
798 prompt "IDE Mode for AMD Alchemy Au1200"
799 default CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
800 depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
801
802config BLK_DEV_IDE_AU1XXX_PIO_DBDMA
803 bool "PIO+DbDMA IDE for AMD Alchemy Au1200"
804
805config BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
806 bool "MDMA2+DbDMA IDE for AMD Alchemy Au1200"
807 depends on SOC_AU1200 && BLK_DEV_IDE_AU1XXX
808endchoice
809
810config BLK_DEV_IDE_AU1XXX_BURSTABLE_ON
811 bool "Enable burstable Mode on DbDMA"
812 default false
813 depends BLK_DEV_IDE_AU1XXX
814 help
815 This option enable the burstable Flag on DbDMA controller
816 (cf. "AMD Alchemy 'Au1200' Processor Data Book - PRELIMINARY").
817
818config BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ
819 int "Maximum transfer size (KB) per request (up to 128)"
820 default "128"
821 depends BLK_DEV_IDE_AU1XXX
822
Linus Torvalds1da177e2005-04-16 15:20:36 -0700823config IDE_ARM
824 def_bool ARM && (ARCH_A5K || ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
825
826config BLK_DEV_IDE_ICSIDE
827 tristate "ICS IDE interface support"
828 depends on ARM && ARCH_ACORN
829 help
830 On Acorn systems, say Y here if you wish to use the ICS IDE
831 interface card. This is not required for ICS partition support.
832 If you are unsure, say N to this.
833
834config BLK_DEV_IDEDMA_ICS
835 bool "ICS DMA support"
836 depends on BLK_DEV_IDE_ICSIDE
837 help
838 Say Y here if you want to add DMA (Direct Memory Access) support to
839 the ICS IDE driver.
840
841config IDEDMA_ICS_AUTO
842 bool "Use ICS DMA by default"
843 depends on BLK_DEV_IDEDMA_ICS
844 help
845 Prior to kernel version 2.1.112, Linux used to automatically use
846 DMA for IDE drives and chipsets which support it. Due to concerns
847 about a couple of cases where buggy hardware may have caused damage,
848 the default is now to NOT use DMA automatically. To revert to the
849 previous behaviour, say Y to this question.
850
851 If you suspect your hardware is at all flakey, say N here.
852 Do NOT email the IDE kernel people regarding this issue!
853
854config BLK_DEV_IDE_RAPIDE
855 tristate "RapIDE interface support"
856 depends on ARM && ARCH_ACORN
857 help
858 Say Y here if you want to support the Yellowstone RapIDE controller
859 manufactured for use with Acorn computers.
860
861config BLK_DEV_IDE_BAST
862 tristate "Simtec BAST / Thorcom VR1000 IDE support"
863 depends on ARM && (ARCH_BAST || MACH_VR1000)
864 help
865 Say Y here if you want to support the onboard IDE channels on the
866 Simtec BAST or the Thorcom VR1000
867
868config BLK_DEV_GAYLE
869 bool "Amiga Gayle IDE interface support"
870 depends on AMIGA
871 help
872 This is the IDE driver for the Amiga Gayle IDE interface. It supports
873 both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
874 This includes builtin IDE interfaces on some Amiga models (A600,
875 A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion
876 bus (M-Tech E-Matrix 530 expansion card).
877 Say Y if you have an Amiga with a Gayle IDE interface and want to use
878 IDE devices (hard disks, CD-ROM drives, etc.) that are connected to
879 it.
880 Note that you also have to enable Zorro bus support if you want to
881 use Gayle IDE interfaces on the Zorro expansion bus.
882
883config BLK_DEV_IDEDOUBLER
884 bool "Amiga IDE Doubler support (EXPERIMENTAL)"
885 depends on BLK_DEV_GAYLE && EXPERIMENTAL
886 ---help---
887 This driver provides support for the so-called `IDE doublers' (made
888 by various manufacturers, e.g. Eyetech) that can be connected to the
889 builtin IDE interface of some Amiga models. Using such an IDE
890 doubler, you can connect up to four instead of two IDE devices on
891 the Amiga's builtin IDE interface.
892
893 Note that the normal Amiga Gayle IDE driver may not work correctly
894 if you have an IDE doubler and don't enable this driver!
895
896 Say Y if you have an IDE doubler. The driver is enabled at kernel
897 runtime using the "ide=doubler" kernel boot parameter.
898
899config BLK_DEV_BUDDHA
900 bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
901 depends on ZORRO && EXPERIMENTAL
902 help
903 This is the IDE driver for the IDE interfaces on the Buddha,
904 Catweasel and X-Surf expansion boards. It supports up to two interfaces
905 on the Buddha, three on the Catweasel and two on the X-Surf.
906
907 Say Y if you have a Buddha or Catweasel expansion board and want to
908 use IDE devices (hard disks, CD-ROM drives, etc.) that are connected
909 to one of its IDE interfaces.
910
911config BLK_DEV_FALCON_IDE
912 bool "Falcon IDE interface support"
913 depends on ATARI
914 help
915 This is the IDE driver for the builtin IDE interface on the Atari
916 Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
917 disks, CD-ROM drives, etc.) that are connected to the builtin IDE
918 interface.
919
920config BLK_DEV_MAC_IDE
921 bool "Macintosh Quadra/Powerbook IDE interface support"
922 depends on MAC
923 help
924 This is the IDE driver for the builtin IDE interface on some m68k
925 Macintosh models. It supports both the `Quadra style' (used in
926 Quadra/ Centris 630 and Performa 588 models) and `Powerbook style'
927 (used in the Powerbook 150 and 190 models) IDE interface.
928
929 Say Y if you have such an Macintosh model and want to use IDE
930 devices (hard disks, CD-ROM drives, etc.) that are connected to the
931 builtin IDE interface.
932
933config BLK_DEV_Q40IDE
934 bool "Q40/Q60 IDE interface support"
935 depends on Q40
936 help
937 Enable the on-board IDE controller in the Q40/Q60. This should
938 normally be on; disable it only if you are running a custom hard
939 drive subsystem through an expansion card.
940
941config BLK_DEV_MPC8xx_IDE
942 bool "MPC8xx IDE support"
Marcelo Tosatti38f9d412005-12-15 02:12:53 +0100943 depends on 8xx && IDE=y && BLK_DEV_IDE=y
Linus Torvalds1da177e2005-04-16 15:20:36 -0700944 help
945 This option provides support for IDE on Motorola MPC8xx Systems.
946 Please see 'Type of MPC8xx IDE interface' for details.
947
948 If unsure, say N.
949
950choice
951 prompt "Type of MPC8xx IDE interface"
952 depends on BLK_DEV_MPC8xx_IDE
953 default IDE_8xx_PCCARD
954
955config IDE_8xx_PCCARD
956 bool "8xx_PCCARD"
957 ---help---
958 Select how the IDE devices are connected to the MPC8xx system:
959
960 8xx_PCCARD uses the 8xx internal PCMCIA interface in combination
961 with a PC Card (e.g. ARGOSY portable Hard Disk Adapter),
962 ATA PC Card HDDs or ATA PC Flash Cards (example: TQM8xxL
963 systems)
964
965 8xx_DIRECT is used for directly connected IDE devices using the 8xx
966 internal PCMCIA interface (example: IVMS8 systems)
967
968 EXT_DIRECT is used for IDE devices directly connected to the 8xx
969 bus using some glue logic, but _not_ the 8xx internal
970 PCMCIA interface (example: IDIF860 systems)
971
972config IDE_8xx_DIRECT
973 bool "8xx_DIRECT"
974
975config IDE_EXT_DIRECT
976 bool "EXT_DIRECT"
977
978endchoice
979
980# no isa -> no vlb
981config IDE_CHIPSETS
982 bool "Other IDE chipset support"
983 depends on ISA
984 ---help---
985 Say Y here if you want to include enhanced support for various IDE
986 interface chipsets used on motherboards and add-on cards. You can
987 then pick your particular IDE chip from among the following options.
988 This enhanced support may be necessary for Linux to be able to
989 access the 3rd/4th drives in some systems. It may also enable
990 setting of higher speed I/O rates to improve system performance with
991 these chipsets. Most of these also require special kernel boot
992 parameters to actually turn on the support at runtime; you can find
993 a list of these in the file <file:Documentation/ide.txt>.
994
995 People with SCSI-only systems can say N here.
996
997if IDE_CHIPSETS
998
999comment "Note: most of these also require special kernel boot parameters"
1000
1001config BLK_DEV_4DRIVES
1002 bool "Generic 4 drives/port support"
1003 help
1004 Certain older chipsets, including the Tekram 690CD, use a single set
1005 of I/O ports at 0x1f0 to control up to four drives, instead of the
1006 customary two drives per port. Support for this can be enabled at
1007 runtime using the "ide0=four" kernel boot parameter if you say Y
1008 here.
1009
1010config BLK_DEV_ALI14XX
1011 tristate "ALI M14xx support"
1012 help
1013 This driver is enabled at runtime using the "ide0=ali14xx" kernel
1014 boot parameter. It enables support for the secondary IDE interface
1015 of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
1016 I/O speeds to be set as well. See the files
1017 <file:Documentation/ide.txt> and <file:drivers/ide/legacy/ali14xx.c> for
1018 more info.
1019
1020config BLK_DEV_DTC2278
1021 tristate "DTC-2278 support"
1022 help
1023 This driver is enabled at runtime using the "ide0=dtc2278" kernel
1024 boot parameter. It enables support for the secondary IDE interface
1025 of the DTC-2278 card, and permits faster I/O speeds to be set as
1026 well. See the <file:Documentation/ide.txt> and
1027 <file:drivers/ide/legacy/dtc2278.c> files for more info.
1028
1029config BLK_DEV_HT6560B
1030 tristate "Holtek HT6560B support"
1031 help
1032 This driver is enabled at runtime using the "ide0=ht6560b" kernel
1033 boot parameter. It enables support for the secondary IDE interface
1034 of the Holtek card, and permits faster I/O speeds to be set as well.
1035 See the <file:Documentation/ide.txt> and
1036 <file:drivers/ide/legacy/ht6560b.c> files for more info.
1037
1038config BLK_DEV_QD65XX
1039 tristate "QDI QD65xx support"
1040 help
1041 This driver is enabled at runtime using the "ide0=qd65xx" kernel
1042 boot parameter. It permits faster I/O speeds to be set. See the
1043 <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
1044 more info.
1045
1046config BLK_DEV_UMC8672
1047 tristate "UMC-8672 support"
1048 help
1049 This driver is enabled at runtime using the "ide0=umc8672" kernel
1050 boot parameter. It enables support for the secondary IDE interface
1051 of the UMC-8672, and permits faster I/O speeds to be set as well.
1052 See the files <file:Documentation/ide.txt> and
1053 <file:drivers/ide/legacy/umc8672.c> for more info.
1054
1055endif
1056
1057config BLK_DEV_IDEDMA
Pete Popov26a940e2005-09-15 08:03:12 +00001058 def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001059
1060config IDEDMA_IVB
1061 bool "IGNORE word93 Validation BITS"
1062 depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
1063 ---help---
1064 There are unclear terms in ATA-4 and ATA-5 standards how certain
1065 hardware (an 80c ribbon) should be detected. Different interpretations
1066 of the standards have been released in hardware. This causes problems:
1067 for example, a host with Ultra Mode 4 (or higher) will not run
1068 in that mode with an 80c ribbon.
1069
1070 If you are experiencing compatibility or performance problems, you
1071 MAY try to answering Y here. However, it does not necessarily solve
1072 any of your problems, it could even cause more of them.
1073
1074 It is normally safe to answer Y; however, the default is N.
1075
1076config IDEDMA_AUTO
1077 def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
1078
1079endif
1080
1081config BLK_DEV_HD_ONLY
1082 bool "Old hard disk (MFM/RLL/IDE) driver"
1083 depends on BLK_DEV_IDE=n
1084 help
1085 There are two drivers for MFM/RLL/IDE hard disks. Most people use
1086 the newer enhanced driver, but this old one is still around for two
1087 reasons. Some older systems have strange timing problems and seem to
1088 work only with the old driver (which itself does not work with some
1089 newer systems). The other reason is that the old driver is smaller,
1090 since it lacks the enhanced functionality of the new one. This makes
1091 it a good choice for systems with very tight memory restrictions, or
1092 for systems with only older MFM/RLL/ESDI drives. Choosing the old
1093 driver can save 13 KB or so of kernel memory.
1094
1095 If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
1096 instead of this one. For more detailed information, read the
1097 Disk-HOWTO, available from
1098 <http://www.tldp.org/docs.html#howto>.
1099
1100config BLK_DEV_HD
1101 def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY
1102
1103endif
1104
1105endmenu