blob: 329a8faa6e37bb32bd6e65f1b8fd758ac45baa36 [file] [log] [blame]
Pierre Ossman5c4e6f12007-05-21 20:23:20 +02001/*
2 * include/linux/mmc/sdio.h
3 *
4 * Copyright 2006-2007 Pierre Ossman
5 *
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or (at
9 * your option) any later version.
10 */
11
12#ifndef MMC_SDIO_H
13#define MMC_SDIO_H
14
15/* SDIO commands type argument response */
16#define SD_IO_SEND_OP_COND 5 /* bcr [23:0] OCR R4 */
Pierre Ossmanb2bcc792007-05-22 20:25:21 +020017#define SD_IO_RW_DIRECT 52 /* ac [31:0] See below R5 */
Pierre Ossman112c9db2007-07-06 13:35:01 +020018#define SD_IO_RW_EXTENDED 53 /* adtc [31:0] See below R5 */
Pierre Ossmanb2bcc792007-05-22 20:25:21 +020019
20/*
21 * SD_IO_RW_DIRECT argument format:
22 *
23 * [31] R/W flag
24 * [30:28] Function number
25 * [27] RAW flag
26 * [25:9] Register address
27 * [7:0] Data
28 */
29
30/*
Pierre Ossman112c9db2007-07-06 13:35:01 +020031 * SD_IO_RW_EXTENDED argument format:
32 *
33 * [31] R/W flag
34 * [30:28] Function number
35 * [27] Block mode
36 * [26] Increment address
37 * [25:9] Register address
38 * [8:0] Byte/block count
39 */
40
41/*
Pierre Ossmanb2bcc792007-05-22 20:25:21 +020042 SDIO status in R5
43 Type
44 e : error bit
45 s : status bit
46 r : detected and set for the actual command response
47 x : detected and set during command execution. the host must poll
48 the card by sending status command in order to read these bits.
49 Clear condition
50 a : according to the card state
51 b : always related to the previous command. Reception of
52 a valid command will clear it (with a delay of one command)
53 c : clear by read
54 */
55
56#define R5_COM_CRC_ERROR (1 << 15) /* er, b */
57#define R5_ILLEGAL_COMMAND (1 << 14) /* er, b */
58#define R5_ERROR (1 << 11) /* erx, c */
59#define R5_FUNCTION_NUMBER (1 << 9) /* er, c */
60#define R5_OUT_OF_RANGE (1 << 8) /* er, c */
61#define R5_STATUS(x) (x & 0xCB00)
62#define R5_IO_CURRENT_STATE(x) ((x & 0x3000) >> 12) /* s, b */
Pierre Ossman5c4e6f12007-05-21 20:23:20 +020063
Pierre Ossmanfa64efa2007-05-27 14:22:37 +020064/*
65 * Card Common Control Registers (CCCR)
66 */
67
68#define SDIO_CCCR_CCCR 0x00
69
70#define SDIO_CCCR_REV_1_00 0 /* CCCR/FBR Version 1.00 */
71#define SDIO_CCCR_REV_1_10 1 /* CCCR/FBR Version 1.10 */
72#define SDIO_CCCR_REV_1_20 2 /* CCCR/FBR Version 1.20 */
73
74#define SDIO_SDIO_REV_1_00 0 /* SDIO Spec Version 1.00 */
75#define SDIO_SDIO_REV_1_10 1 /* SDIO Spec Version 1.10 */
76#define SDIO_SDIO_REV_1_20 2 /* SDIO Spec Version 1.20 */
77#define SDIO_SDIO_REV_2_00 3 /* SDIO Spec Version 2.00 */
78
79#define SDIO_CCCR_SD 0x01
80
81#define SDIO_SD_REV_1_01 0 /* SD Physical Spec Version 1.01 */
82#define SDIO_SD_REV_1_10 1 /* SD Physical Spec Version 1.10 */
83#define SDIO_SD_REV_2_00 2 /* SD Physical Spec Version 2.00 */
84
85#define SDIO_CCCR_IOEx 0x02
86#define SDIO_CCCR_IORx 0x03
87
88#define SDIO_CCCR_IENx 0x04 /* Function/Master Interrupt Enable */
89#define SDIO_CCCR_INTx 0x05 /* Function Interrupt Pending */
90
91#define SDIO_CCCR_ABORT 0x06 /* function abort/card reset */
92
93#define SDIO_CCCR_IF 0x07 /* bus interface controls */
94
95#define SDIO_BUS_WIDTH_1BIT 0x00
96#define SDIO_BUS_WIDTH_4BIT 0x02
Daniel Mack8a64c0f2010-04-06 10:52:44 +020097#define SDIO_BUS_ECSI 0x20 /* Enable continuous SPI interrupt */
98#define SDIO_BUS_SCSI 0x40 /* Support continuous SPI interrupt */
Pierre Ossmanfa64efa2007-05-27 14:22:37 +020099
Daniel Drake6b5eda32010-03-05 13:43:34 -0800100#define SDIO_BUS_ASYNC_INT 0x20
101
Pierre Ossmanfa64efa2007-05-27 14:22:37 +0200102#define SDIO_BUS_CD_DISABLE 0x80 /* disable pull-up on DAT3 (pin 1) */
103
104#define SDIO_CCCR_CAPS 0x08
105
106#define SDIO_CCCR_CAP_SDC 0x01 /* can do CMD52 while data transfer */
107#define SDIO_CCCR_CAP_SMB 0x02 /* can do multi-block xfers (CMD53) */
108#define SDIO_CCCR_CAP_SRW 0x04 /* supports read-wait protocol */
109#define SDIO_CCCR_CAP_SBS 0x08 /* supports suspend/resume */
110#define SDIO_CCCR_CAP_S4MI 0x10 /* interrupt during 4-bit CMD53 */
111#define SDIO_CCCR_CAP_E4MI 0x20 /* enable ints during 4-bit CMD53 */
112#define SDIO_CCCR_CAP_LSC 0x40 /* low speed card */
113#define SDIO_CCCR_CAP_4BLS 0x80 /* 4 bit low speed card */
114
115#define SDIO_CCCR_CIS 0x09 /* common CIS pointer (3 bytes) */
116
117/* Following 4 regs are valid only if SBS is set */
118#define SDIO_CCCR_SUSPEND 0x0c
119#define SDIO_CCCR_SELx 0x0d
120#define SDIO_CCCR_EXECx 0x0e
121#define SDIO_CCCR_READYx 0x0f
122
123#define SDIO_CCCR_BLKSIZE 0x10
124
125#define SDIO_CCCR_POWER 0x12
126
127#define SDIO_POWER_SMPC 0x01 /* Supports Master Power Control */
128#define SDIO_POWER_EMPC 0x02 /* Enable Master Power Control */
129
130#define SDIO_CCCR_SPEED 0x13
131
132#define SDIO_SPEED_SHS 0x01 /* Supports High-Speed mode */
133#define SDIO_SPEED_EHS 0x02 /* Enable High-Speed mode */
134
135/*
136 * Function Basic Registers (FBR)
137 */
138
David Vrabel7616ee92007-08-08 14:23:05 +0100139#define SDIO_FBR_BASE(f) ((f) * 0x100) /* base of function f's FBRs */
140
Pierre Ossmanfa64efa2007-05-27 14:22:37 +0200141#define SDIO_FBR_STD_IF 0x00
142
143#define SDIO_FBR_SUPPORTS_CSA 0x40 /* supports Code Storage Area */
144#define SDIO_FBR_ENABLE_CSA 0x80 /* enable Code Storage Area */
145
146#define SDIO_FBR_STD_IF_EXT 0x01
147
148#define SDIO_FBR_POWER 0x02
149
150#define SDIO_FBR_POWER_SPS 0x01 /* Supports Power Selection */
151#define SDIO_FBR_POWER_EPS 0x02 /* Enable (low) Power Selection */
152
153#define SDIO_FBR_CIS 0x09 /* CIS pointer (3 bytes) */
154
155
156#define SDIO_FBR_CSA 0x0C /* CSA pointer (3 bytes) */
157
158#define SDIO_FBR_CSA_DATA 0x0F
159
160#define SDIO_FBR_BLKSIZE 0x10 /* block size (2 bytes) */
161
Pierre Ossman5c4e6f12007-05-21 20:23:20 +0200162#endif
163