Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 1 | /* |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 2 | * Copyright (C) 2004 Red Hat <alan@redhat.com> |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 3 | * Copyright (C) 2007 Bartlomiej Zolnierkiewicz |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 4 | * |
| 5 | * May be copied or modified under the terms of the GNU General Public License |
| 6 | * Based in part on the ITE vendor provided SCSI driver. |
| 7 | * |
| 8 | * Documentation available from |
| 9 | * http://www.ite.com.tw/pc/IT8212F_V04.pdf |
| 10 | * Some other documents are NDA. |
| 11 | * |
| 12 | * The ITE8212 isn't exactly a standard IDE controller. It has two |
| 13 | * modes. In pass through mode then it is an IDE controller. In its smart |
| 14 | * mode its actually quite a capable hardware raid controller disguised |
| 15 | * as an IDE controller. Smart mode only understands DMA read/write and |
| 16 | * identify, none of the fancier commands apply. The IT8211 is identical |
| 17 | * in other respects but lacks the raid mode. |
| 18 | * |
| 19 | * Errata: |
| 20 | * o Rev 0x10 also requires master/slave hold the same DMA timings and |
| 21 | * cannot do ATAPI MWDMA. |
| 22 | * o The identify data for raid volumes lacks CHS info (technically ok) |
| 23 | * but also fails to set the LBA28 and other bits. We fix these in |
| 24 | * the IDE probe quirk code. |
| 25 | * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode |
| 26 | * raid then the controller firmware dies |
| 27 | * o Smart mode without RAID doesn't clear all the necessary identify |
| 28 | * bits to reduce the command set to the one used |
| 29 | * |
| 30 | * This has a few impacts on the driver |
| 31 | * - In pass through mode we do all the work you would expect |
| 32 | * - In smart mode the clocking set up is done by the controller generally |
| 33 | * but we must watch the other limits and filter. |
| 34 | * - There are a few extra vendor commands that actually talk to the |
| 35 | * controller but only work PIO with no IRQ. |
| 36 | * |
| 37 | * Vendor areas of the identify block in smart mode are used for the |
| 38 | * timing and policy set up. Each HDD in raid mode also has a serial |
| 39 | * block on the disk. The hardware extra commands are get/set chip status, |
| 40 | * rebuild, get rebuild status. |
| 41 | * |
| 42 | * In Linux the driver supports pass through mode as if the device was |
| 43 | * just another IDE controller. If the smart mode is running then |
| 44 | * volumes are managed by the controller firmware and each IDE "disk" |
| 45 | * is a raid volume. Even more cute - the controller can do automated |
| 46 | * hotplug and rebuild. |
| 47 | * |
| 48 | * The pass through controller itself is a little demented. It has a |
| 49 | * flaw that it has a single set of PIO/MWDMA timings per channel so |
| 50 | * non UDMA devices restrict each others performance. It also has a |
| 51 | * single clock source per channel so mixed UDMA100/133 performance |
| 52 | * isn't perfect and we have to pick a clock. Thankfully none of this |
| 53 | * matters in smart mode. ATAPI DMA is not currently supported. |
| 54 | * |
| 55 | * It seems the smart mode is a win for RAID1/RAID10 but otherwise not. |
| 56 | * |
| 57 | * TODO |
| 58 | * - ATAPI UDMA is ok but not MWDMA it seems |
| 59 | * - RAID configuration ioctls |
| 60 | * - Move to libata once it grows up |
| 61 | */ |
| 62 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 63 | #include <linux/types.h> |
| 64 | #include <linux/module.h> |
| 65 | #include <linux/pci.h> |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 66 | #include <linux/hdreg.h> |
| 67 | #include <linux/ide.h> |
| 68 | #include <linux/init.h> |
| 69 | |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 70 | #define DRV_NAME "it821x" |
| 71 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 72 | struct it821x_dev |
| 73 | { |
| 74 | unsigned int smart:1, /* Are we in smart raid mode */ |
| 75 | timing10:1; /* Rev 0x10 */ |
| 76 | u8 clock_mode; /* 0, ATA_50 or ATA_66 */ |
| 77 | u8 want[2][2]; /* Mode/Pri log for master slave */ |
| 78 | /* We need these for switching the clock when DMA goes on/off |
| 79 | The high byte is the 66Mhz timing */ |
| 80 | u16 pio[2]; /* Cached PIO values */ |
| 81 | u16 mwdma[2]; /* Cached MWDMA values */ |
| 82 | u16 udma[2]; /* Cached UDMA values (per drive) */ |
| 83 | }; |
| 84 | |
| 85 | #define ATA_66 0 |
| 86 | #define ATA_50 1 |
| 87 | #define ATA_ANY 2 |
| 88 | |
| 89 | #define UDMA_OFF 0 |
| 90 | #define MWDMA_OFF 0 |
| 91 | |
| 92 | /* |
| 93 | * We allow users to force the card into non raid mode without |
Robert P. J. Day | 3a4fa0a | 2007-10-19 23:10:43 +0200 | [diff] [blame] | 94 | * flashing the alternative BIOS. This is also necessary right now |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 95 | * for embedded platforms that cannot run a PC BIOS but are using this |
| 96 | * device. |
| 97 | */ |
| 98 | |
| 99 | static int it8212_noraid; |
| 100 | |
| 101 | /** |
| 102 | * it821x_program - program the PIO/MWDMA registers |
| 103 | * @drive: drive to tune |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 104 | * @timing: timing info |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 105 | * |
| 106 | * Program the PIO/MWDMA timing for this channel according to the |
| 107 | * current clock. |
| 108 | */ |
| 109 | |
| 110 | static void it821x_program(ide_drive_t *drive, u16 timing) |
| 111 | { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 112 | ide_hwif_t *hwif = drive->hwif; |
| 113 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 114 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 115 | int channel = hwif->channel; |
| 116 | u8 conf; |
| 117 | |
| 118 | /* Program PIO/MWDMA timing bits */ |
| 119 | if(itdev->clock_mode == ATA_66) |
| 120 | conf = timing >> 8; |
| 121 | else |
| 122 | conf = timing & 0xFF; |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 123 | |
| 124 | pci_write_config_byte(dev, 0x54 + 4 * channel, conf); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 125 | } |
| 126 | |
| 127 | /** |
| 128 | * it821x_program_udma - program the UDMA registers |
| 129 | * @drive: drive to tune |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 130 | * @timing: timing info |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 131 | * |
| 132 | * Program the UDMA timing for this drive according to the |
| 133 | * current clock. |
| 134 | */ |
| 135 | |
| 136 | static void it821x_program_udma(ide_drive_t *drive, u16 timing) |
| 137 | { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 138 | ide_hwif_t *hwif = drive->hwif; |
| 139 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 140 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 141 | int channel = hwif->channel; |
| 142 | int unit = drive->select.b.unit; |
| 143 | u8 conf; |
| 144 | |
| 145 | /* Program UDMA timing bits */ |
| 146 | if(itdev->clock_mode == ATA_66) |
| 147 | conf = timing >> 8; |
| 148 | else |
| 149 | conf = timing & 0xFF; |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 150 | |
| 151 | if (itdev->timing10 == 0) |
| 152 | pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 153 | else { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 154 | pci_write_config_byte(dev, 0x56 + 4 * channel, conf); |
| 155 | pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 156 | } |
| 157 | } |
| 158 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 159 | /** |
| 160 | * it821x_clock_strategy |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 161 | * @drive: drive to set up |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 162 | * |
| 163 | * Select between the 50 and 66Mhz base clocks to get the best |
| 164 | * results for this interface. |
| 165 | */ |
| 166 | |
| 167 | static void it821x_clock_strategy(ide_drive_t *drive) |
| 168 | { |
| 169 | ide_hwif_t *hwif = drive->hwif; |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 170 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 171 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 172 | |
| 173 | u8 unit = drive->select.b.unit; |
| 174 | ide_drive_t *pair = &hwif->drives[1-unit]; |
| 175 | |
| 176 | int clock, altclock; |
| 177 | u8 v; |
| 178 | int sel = 0; |
| 179 | |
| 180 | if(itdev->want[0][0] > itdev->want[1][0]) { |
| 181 | clock = itdev->want[0][1]; |
| 182 | altclock = itdev->want[1][1]; |
| 183 | } else { |
| 184 | clock = itdev->want[1][1]; |
| 185 | altclock = itdev->want[0][1]; |
| 186 | } |
| 187 | |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 188 | /* |
| 189 | * if both clocks can be used for the mode with the higher priority |
| 190 | * use the clock needed by the mode with the lower priority |
| 191 | */ |
| 192 | if (clock == ATA_ANY) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 193 | clock = altclock; |
| 194 | |
| 195 | /* Nobody cares - keep the same clock */ |
| 196 | if(clock == ATA_ANY) |
| 197 | return; |
| 198 | /* No change */ |
| 199 | if(clock == itdev->clock_mode) |
| 200 | return; |
| 201 | |
| 202 | /* Load this into the controller ? */ |
| 203 | if(clock == ATA_66) |
| 204 | itdev->clock_mode = ATA_66; |
| 205 | else { |
| 206 | itdev->clock_mode = ATA_50; |
| 207 | sel = 1; |
| 208 | } |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 209 | |
| 210 | pci_read_config_byte(dev, 0x50, &v); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 211 | v &= ~(1 << (1 + hwif->channel)); |
| 212 | v |= sel << (1 + hwif->channel); |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 213 | pci_write_config_byte(dev, 0x50, v); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 214 | |
| 215 | /* |
| 216 | * Reprogram the UDMA/PIO of the pair drive for the switch |
| 217 | * MWDMA will be dealt with by the dma switcher |
| 218 | */ |
| 219 | if(pair && itdev->udma[1-unit] != UDMA_OFF) { |
| 220 | it821x_program_udma(pair, itdev->udma[1-unit]); |
| 221 | it821x_program(pair, itdev->pio[1-unit]); |
| 222 | } |
| 223 | /* |
| 224 | * Reprogram the UDMA/PIO of our drive for the switch. |
| 225 | * MWDMA will be dealt with by the dma switcher |
| 226 | */ |
| 227 | if(itdev->udma[unit] != UDMA_OFF) { |
| 228 | it821x_program_udma(drive, itdev->udma[unit]); |
| 229 | it821x_program(drive, itdev->pio[unit]); |
| 230 | } |
| 231 | } |
| 232 | |
| 233 | /** |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 234 | * it821x_set_pio_mode - set host controller for PIO mode |
| 235 | * @drive: drive |
| 236 | * @pio: PIO mode number |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 237 | * |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 238 | * Tune the host to the desired PIO mode taking into the consideration |
| 239 | * the maximum PIO mode supported by the other device on the cable. |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 240 | */ |
| 241 | |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 242 | static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 243 | { |
| 244 | ide_hwif_t *hwif = drive->hwif; |
| 245 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 246 | int unit = drive->select.b.unit; |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 247 | ide_drive_t *pair = &hwif->drives[1 - unit]; |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 248 | u8 set_pio = pio; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 249 | |
| 250 | /* Spec says 89 ref driver uses 88 */ |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 251 | static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 }; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 252 | static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY }; |
| 253 | |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 254 | /* |
| 255 | * Compute the best PIO mode we can for a given device. We must |
| 256 | * pick a speed that does not cause problems with the other device |
| 257 | * on the cable. |
| 258 | */ |
| 259 | if (pair) { |
Bartlomiej Zolnierkiewicz | 2134758 | 2007-07-20 01:11:58 +0200 | [diff] [blame] | 260 | u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4); |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 261 | /* trim PIO to the slowest of the master/slave */ |
| 262 | if (pair_pio < set_pio) |
| 263 | set_pio = pair_pio; |
| 264 | } |
| 265 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 266 | /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ |
Bartlomiej Zolnierkiewicz | 0e9b4e5 | 2007-05-05 22:03:50 +0200 | [diff] [blame] | 267 | itdev->want[unit][1] = pio_want[set_pio]; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 268 | itdev->want[unit][0] = 1; /* PIO is lowest priority */ |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 269 | itdev->pio[unit] = pio_timings[set_pio]; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 270 | it821x_clock_strategy(drive); |
| 271 | it821x_program(drive, itdev->pio[unit]); |
| 272 | } |
| 273 | |
| 274 | /** |
| 275 | * it821x_tune_mwdma - tune a channel for MWDMA |
| 276 | * @drive: drive to set up |
| 277 | * @mode_wanted: the target operating mode |
| 278 | * |
| 279 | * Load the timing settings for this device mode into the |
| 280 | * controller when doing MWDMA in pass through mode. The caller |
| 281 | * must manage the whole lack of per device MWDMA/PIO timings and |
| 282 | * the shared MWDMA/PIO timing register. |
| 283 | */ |
| 284 | |
| 285 | static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted) |
| 286 | { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 287 | ide_hwif_t *hwif = drive->hwif; |
| 288 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 289 | struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif); |
| 290 | int unit = drive->select.b.unit; |
| 291 | int channel = hwif->channel; |
| 292 | u8 conf; |
| 293 | |
| 294 | static u16 dma[] = { 0x8866, 0x3222, 0x3121 }; |
| 295 | static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY }; |
| 296 | |
| 297 | itdev->want[unit][1] = mwdma_want[mode_wanted]; |
| 298 | itdev->want[unit][0] = 2; /* MWDMA is low priority */ |
| 299 | itdev->mwdma[unit] = dma[mode_wanted]; |
| 300 | itdev->udma[unit] = UDMA_OFF; |
| 301 | |
| 302 | /* UDMA bits off - Revision 0x10 do them in pairs */ |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 303 | pci_read_config_byte(dev, 0x50, &conf); |
| 304 | if (itdev->timing10) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 305 | conf |= channel ? 0x60: 0x18; |
| 306 | else |
| 307 | conf |= 1 << (3 + 2 * channel + unit); |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 308 | pci_write_config_byte(dev, 0x50, conf); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 309 | |
| 310 | it821x_clock_strategy(drive); |
| 311 | /* FIXME: do we need to program this ? */ |
| 312 | /* it821x_program(drive, itdev->mwdma[unit]); */ |
| 313 | } |
| 314 | |
| 315 | /** |
| 316 | * it821x_tune_udma - tune a channel for UDMA |
| 317 | * @drive: drive to set up |
| 318 | * @mode_wanted: the target operating mode |
| 319 | * |
| 320 | * Load the timing settings for this device mode into the |
| 321 | * controller when doing UDMA modes in pass through. |
| 322 | */ |
| 323 | |
| 324 | static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted) |
| 325 | { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 326 | ide_hwif_t *hwif = drive->hwif; |
| 327 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 328 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 329 | int unit = drive->select.b.unit; |
| 330 | int channel = hwif->channel; |
| 331 | u8 conf; |
| 332 | |
| 333 | static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 }; |
| 334 | static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 }; |
| 335 | |
| 336 | itdev->want[unit][1] = udma_want[mode_wanted]; |
| 337 | itdev->want[unit][0] = 3; /* UDMA is high priority */ |
| 338 | itdev->mwdma[unit] = MWDMA_OFF; |
| 339 | itdev->udma[unit] = udma[mode_wanted]; |
| 340 | if(mode_wanted >= 5) |
| 341 | itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */ |
| 342 | |
| 343 | /* UDMA on. Again revision 0x10 must do the pair */ |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 344 | pci_read_config_byte(dev, 0x50, &conf); |
| 345 | if (itdev->timing10) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 346 | conf &= channel ? 0x9F: 0xE7; |
| 347 | else |
| 348 | conf &= ~ (1 << (3 + 2 * channel + unit)); |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 349 | pci_write_config_byte(dev, 0x50, conf); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 350 | |
| 351 | it821x_clock_strategy(drive); |
| 352 | it821x_program_udma(drive, itdev->udma[unit]); |
| 353 | |
| 354 | } |
| 355 | |
| 356 | /** |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 357 | * it821x_dma_read - DMA hook |
| 358 | * @drive: drive for DMA |
| 359 | * |
| 360 | * The IT821x has a single timing register for MWDMA and for PIO |
| 361 | * operations. As we flip back and forth we have to reload the |
| 362 | * clock. In addition the rev 0x10 device only works if the same |
| 363 | * timing value is loaded into the master and slave UDMA clock |
| 364 | * so we must also reload that. |
| 365 | * |
| 366 | * FIXME: we could figure out in advance if we need to do reloads |
| 367 | */ |
| 368 | |
| 369 | static void it821x_dma_start(ide_drive_t *drive) |
| 370 | { |
| 371 | ide_hwif_t *hwif = drive->hwif; |
| 372 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 373 | int unit = drive->select.b.unit; |
| 374 | if(itdev->mwdma[unit] != MWDMA_OFF) |
| 375 | it821x_program(drive, itdev->mwdma[unit]); |
| 376 | else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10) |
| 377 | it821x_program_udma(drive, itdev->udma[unit]); |
| 378 | ide_dma_start(drive); |
| 379 | } |
| 380 | |
| 381 | /** |
| 382 | * it821x_dma_write - DMA hook |
| 383 | * @drive: drive for DMA stop |
| 384 | * |
| 385 | * The IT821x has a single timing register for MWDMA and for PIO |
| 386 | * operations. As we flip back and forth we have to reload the |
| 387 | * clock. |
| 388 | */ |
| 389 | |
| 390 | static int it821x_dma_end(ide_drive_t *drive) |
| 391 | { |
| 392 | ide_hwif_t *hwif = drive->hwif; |
| 393 | int unit = drive->select.b.unit; |
| 394 | struct it821x_dev *itdev = ide_get_hwifdata(hwif); |
| 395 | int ret = __ide_dma_end(drive); |
| 396 | if(itdev->mwdma[unit] != MWDMA_OFF) |
| 397 | it821x_program(drive, itdev->pio[unit]); |
| 398 | return ret; |
| 399 | } |
| 400 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 401 | /** |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 402 | * it821x_set_dma_mode - set host controller for DMA mode |
| 403 | * @drive: drive |
| 404 | * @speed: DMA mode |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 405 | * |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 406 | * Tune the ITE chipset for the desired DMA mode. |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 407 | */ |
| 408 | |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 409 | static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 410 | { |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 411 | /* |
| 412 | * MWDMA tuning is really hard because our MWDMA and PIO |
| 413 | * timings are kept in the same place. We can switch in the |
| 414 | * host dma on/off callbacks. |
| 415 | */ |
| 416 | if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6) |
| 417 | it821x_tune_udma(drive, speed - XFER_UDMA_0); |
| 418 | else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) |
| 419 | it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 420 | } |
| 421 | |
| 422 | /** |
Bartlomiej Zolnierkiewicz | ac95bee | 2008-04-26 22:25:14 +0200 | [diff] [blame] | 423 | * it821x_cable_detect - cable detection |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 424 | * @hwif: interface to check |
| 425 | * |
| 426 | * Check for the presence of an ATA66 capable cable on the |
| 427 | * interface. Problematic as it seems some cards don't have |
| 428 | * the needed logic onboard. |
| 429 | */ |
| 430 | |
Bartlomiej Zolnierkiewicz | ac95bee | 2008-04-26 22:25:14 +0200 | [diff] [blame] | 431 | static u8 __devinit it821x_cable_detect(ide_hwif_t *hwif) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 432 | { |
| 433 | /* The reference driver also only does disk side */ |
Bartlomiej Zolnierkiewicz | 49521f9 | 2007-07-09 23:17:58 +0200 | [diff] [blame] | 434 | return ATA_CBL_PATA80; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 435 | } |
| 436 | |
| 437 | /** |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 438 | * it821x_quirkproc - post init callback |
| 439 | * @drive: drive |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 440 | * |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 441 | * This callback is run after the drive has been probed but |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 442 | * before anything gets attached. It allows drivers to do any |
| 443 | * final tuning that is needed, or fixups to work around bugs. |
| 444 | */ |
| 445 | |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 446 | static void __devinit it821x_quirkproc(ide_drive_t *drive) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 447 | { |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 448 | struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif); |
| 449 | struct hd_driveid *id = drive->id; |
| 450 | u16 *idbits = (u16 *)drive->id; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 451 | |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 452 | if (!itdev->smart) { |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 453 | /* |
| 454 | * If we are in pass through mode then not much |
| 455 | * needs to be done, but we do bother to clear the |
| 456 | * IRQ mask as we may well be in PIO (eg rev 0x10) |
| 457 | * for now and we know unmasking is safe on this chipset. |
| 458 | */ |
Bartlomiej Zolnierkiewicz | f01393e | 2008-01-26 20:13:03 +0100 | [diff] [blame] | 459 | drive->unmask = 1; |
| 460 | } else { |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 461 | /* |
| 462 | * Perform fixups on smart mode. We need to "lose" some |
| 463 | * capabilities the firmware lacks but does not filter, and |
| 464 | * also patch up some capability bits that it forgets to set |
| 465 | * in RAID mode. |
| 466 | */ |
| 467 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 468 | /* Check for RAID v native */ |
| 469 | if(strstr(id->model, "Integrated Technology Express")) { |
| 470 | /* In raid mode the ident block is slightly buggy |
| 471 | We need to set the bits so that the IDE layer knows |
| 472 | LBA28. LBA48 and DMA ar valid */ |
| 473 | id->capability |= 3; /* LBA28, DMA */ |
| 474 | id->command_set_2 |= 0x0400; /* LBA48 valid */ |
| 475 | id->cfs_enable_2 |= 0x0400; /* LBA48 on */ |
| 476 | /* Reporting logic */ |
| 477 | printk(KERN_INFO "%s: IT8212 %sRAID %d volume", |
| 478 | drive->name, |
| 479 | idbits[147] ? "Bootable ":"", |
| 480 | idbits[129]); |
| 481 | if(idbits[129] != 1) |
| 482 | printk("(%dK stripe)", idbits[146]); |
| 483 | printk(".\n"); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 484 | } else { |
| 485 | /* Non RAID volume. Fixups to stop the core code |
| 486 | doing unsupported things */ |
Bartlomiej Zolnierkiewicz | 0380dad | 2007-06-08 15:14:29 +0200 | [diff] [blame] | 487 | id->field_valid &= 3; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 488 | id->queue_depth = 0; |
| 489 | id->command_set_1 = 0; |
| 490 | id->command_set_2 &= 0xC400; |
| 491 | id->cfsse &= 0xC000; |
| 492 | id->cfs_enable_1 = 0; |
| 493 | id->cfs_enable_2 &= 0xC400; |
| 494 | id->csf_default &= 0xC000; |
| 495 | id->word127 = 0; |
| 496 | id->dlf = 0; |
| 497 | id->csfo = 0; |
| 498 | id->cfa_power = 0; |
| 499 | printk(KERN_INFO "%s: Performing identify fixups.\n", |
| 500 | drive->name); |
| 501 | } |
Bartlomiej Zolnierkiewicz | 0380dad | 2007-06-08 15:14:29 +0200 | [diff] [blame] | 502 | |
| 503 | /* |
| 504 | * Set MWDMA0 mode as enabled/support - just to tell |
| 505 | * IDE core that DMA is supported (it821x hardware |
| 506 | * takes care of DMA mode programming). |
| 507 | */ |
| 508 | if (id->capability & 1) { |
| 509 | id->dma_mword |= 0x0101; |
| 510 | drive->current_speed = XFER_MW_DMA_0; |
| 511 | } |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 512 | } |
| 513 | |
| 514 | } |
| 515 | |
Bartlomiej Zolnierkiewicz | 5e37bdc | 2008-04-26 22:25:24 +0200 | [diff] [blame] | 516 | static struct ide_dma_ops it821x_pass_through_dma_ops = { |
Dimitri Gorokhovik | 84e0f3f | 2008-07-16 20:33:34 +0200 | [diff] [blame] | 517 | .dma_host_set = ide_dma_host_set, |
| 518 | .dma_setup = ide_dma_setup, |
| 519 | .dma_exec_cmd = ide_dma_exec_cmd, |
Bartlomiej Zolnierkiewicz | 5e37bdc | 2008-04-26 22:25:24 +0200 | [diff] [blame] | 520 | .dma_start = it821x_dma_start, |
| 521 | .dma_end = it821x_dma_end, |
Dimitri Gorokhovik | 84e0f3f | 2008-07-16 20:33:34 +0200 | [diff] [blame] | 522 | .dma_test_irq = ide_dma_test_irq, |
| 523 | .dma_timeout = ide_dma_timeout, |
| 524 | .dma_lost_irq = ide_dma_lost_irq, |
Bartlomiej Zolnierkiewicz | 5e37bdc | 2008-04-26 22:25:24 +0200 | [diff] [blame] | 525 | }; |
| 526 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 527 | /** |
| 528 | * init_hwif_it821x - set up hwif structs |
| 529 | * @hwif: interface to set up |
| 530 | * |
| 531 | * We do the basic set up of the interface structure. The IT8212 |
| 532 | * requires several custom handlers so we override the default |
| 533 | * ide DMA handlers appropriately |
| 534 | */ |
| 535 | |
| 536 | static void __devinit init_hwif_it821x(ide_hwif_t *hwif) |
| 537 | { |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 538 | struct pci_dev *dev = to_pci_dev(hwif->dev); |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 539 | struct ide_host *host = pci_get_drvdata(dev); |
| 540 | struct it821x_dev *itdevs = host->host_priv; |
| 541 | struct it821x_dev *idev = itdevs + hwif->channel; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 542 | u8 conf; |
| 543 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 544 | ide_set_hwifdata(hwif, idev); |
| 545 | |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 546 | pci_read_config_byte(dev, 0x50, &conf); |
Bartlomiej Zolnierkiewicz | 33c1002 | 2007-10-19 00:30:06 +0200 | [diff] [blame] | 547 | if (conf & 1) { |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 548 | idev->smart = 1; |
Bartlomiej Zolnierkiewicz | 33c1002 | 2007-10-19 00:30:06 +0200 | [diff] [blame] | 549 | hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 550 | /* Long I/O's although allowed in LBA48 space cause the |
| 551 | onboard firmware to enter the twighlight zone */ |
| 552 | hwif->rqsize = 256; |
| 553 | } |
| 554 | |
| 555 | /* Pull the current clocks from 0x50 also */ |
| 556 | if (conf & (1 << (1 + hwif->channel))) |
| 557 | idev->clock_mode = ATA_50; |
| 558 | else |
| 559 | idev->clock_mode = ATA_66; |
| 560 | |
| 561 | idev->want[0][1] = ATA_ANY; |
| 562 | idev->want[1][1] = ATA_ANY; |
| 563 | |
| 564 | /* |
| 565 | * Not in the docs but according to the reference driver |
Robert P. J. Day | 3a4fa0a | 2007-10-19 23:10:43 +0200 | [diff] [blame] | 566 | * this is necessary. |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 567 | */ |
| 568 | |
Bartlomiej Zolnierkiewicz | 3650165 | 2008-02-01 23:09:31 +0100 | [diff] [blame] | 569 | pci_read_config_byte(dev, 0x08, &conf); |
Bartlomiej Zolnierkiewicz | 33c1002 | 2007-10-19 00:30:06 +0200 | [diff] [blame] | 570 | if (conf == 0x10) { |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 571 | idev->timing10 = 1; |
Bartlomiej Zolnierkiewicz | 33c1002 | 2007-10-19 00:30:06 +0200 | [diff] [blame] | 572 | hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA; |
| 573 | if (idev->smart == 0) |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 574 | printk(KERN_WARNING DRV_NAME " %s: revision 0x10, " |
Bartlomiej Zolnierkiewicz | 28cfd8a | 2008-07-24 22:53:31 +0200 | [diff] [blame] | 575 | "workarounds activated\n", pci_name(dev)); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 576 | } |
| 577 | |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 578 | if (idev->smart == 0) { |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 579 | /* MWDMA/PIO clock switching for pass through mode */ |
Bartlomiej Zolnierkiewicz | 5e37bdc | 2008-04-26 22:25:24 +0200 | [diff] [blame] | 580 | hwif->dma_ops = &it821x_pass_through_dma_ops; |
Bartlomiej Zolnierkiewicz | 88b2b32 | 2007-10-13 17:47:51 +0200 | [diff] [blame] | 581 | } else |
| 582 | hwif->host_flags |= IDE_HFLAG_NO_SET_MODE; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 583 | |
Bartlomiej Zolnierkiewicz | 9ff6f72 | 2007-10-16 22:29:58 +0200 | [diff] [blame] | 584 | if (hwif->dma_base == 0) |
| 585 | return; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 586 | |
Bartlomiej Zolnierkiewicz | 5f8b6c3 | 2007-10-19 00:30:07 +0200 | [diff] [blame] | 587 | hwif->ultra_mask = ATA_UDMA6; |
| 588 | hwif->mwdma_mask = ATA_MWDMA2; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 589 | } |
| 590 | |
| 591 | static void __devinit it8212_disable_raid(struct pci_dev *dev) |
| 592 | { |
| 593 | /* Reset local CPU, and set BIOS not ready */ |
| 594 | pci_write_config_byte(dev, 0x5E, 0x01); |
| 595 | |
| 596 | /* Set to bypass mode, and reset PCI bus */ |
| 597 | pci_write_config_byte(dev, 0x50, 0x00); |
| 598 | pci_write_config_word(dev, PCI_COMMAND, |
| 599 | PCI_COMMAND_PARITY | PCI_COMMAND_IO | |
| 600 | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); |
| 601 | pci_write_config_word(dev, 0x40, 0xA0F3); |
| 602 | |
| 603 | pci_write_config_dword(dev,0x4C, 0x02040204); |
| 604 | pci_write_config_byte(dev, 0x42, 0x36); |
Alan Cox | 0c866b5 | 2006-02-03 03:04:58 -0800 | [diff] [blame] | 605 | pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 606 | } |
| 607 | |
Bartlomiej Zolnierkiewicz | a326b02 | 2008-07-24 22:53:33 +0200 | [diff] [blame^] | 608 | static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev) |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 609 | { |
| 610 | u8 conf; |
| 611 | static char *mode[2] = { "pass through", "smart" }; |
| 612 | |
| 613 | /* Force the card into bypass mode if so requested */ |
| 614 | if (it8212_noraid) { |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 615 | printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n", |
Bartlomiej Zolnierkiewicz | 28cfd8a | 2008-07-24 22:53:31 +0200 | [diff] [blame] | 616 | pci_name(dev)); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 617 | it8212_disable_raid(dev); |
| 618 | } |
| 619 | pci_read_config_byte(dev, 0x50, &conf); |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 620 | printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n", |
Bartlomiej Zolnierkiewicz | 28cfd8a | 2008-07-24 22:53:31 +0200 | [diff] [blame] | 621 | pci_name(dev), mode[conf & 1]); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 622 | return 0; |
| 623 | } |
| 624 | |
Bartlomiej Zolnierkiewicz | ac95bee | 2008-04-26 22:25:14 +0200 | [diff] [blame] | 625 | static const struct ide_port_ops it821x_port_ops = { |
| 626 | /* it821x_set_{pio,dma}_mode() are only used in pass-through mode */ |
| 627 | .set_pio_mode = it821x_set_pio_mode, |
| 628 | .set_dma_mode = it821x_set_dma_mode, |
| 629 | .quirkproc = it821x_quirkproc, |
| 630 | .cable_detect = it821x_cable_detect, |
| 631 | }; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 632 | |
Bartlomiej Zolnierkiewicz | 04ba6e7 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 633 | static const struct ide_port_info it821x_chipset __devinitdata = { |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 634 | .name = DRV_NAME, |
Bartlomiej Zolnierkiewicz | 04ba6e7 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 635 | .init_chipset = init_chipset_it821x, |
| 636 | .init_hwif = init_hwif_it821x, |
| 637 | .port_ops = &it821x_port_ops, |
| 638 | .pio_mask = ATA_PIO4, |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 639 | }; |
| 640 | |
| 641 | /** |
| 642 | * it821x_init_one - pci layer discovery entry |
| 643 | * @dev: PCI device |
| 644 | * @id: ident table entry |
| 645 | * |
| 646 | * Called by the PCI code when it finds an ITE821x controller. |
| 647 | * We then use the IDE PCI generic helper to do most of the work. |
| 648 | */ |
| 649 | |
| 650 | static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id) |
| 651 | { |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 652 | struct it821x_dev *itdevs; |
| 653 | int rc; |
Bartlomiej Zolnierkiewicz | eb7a07e | 2008-04-26 17:36:42 +0200 | [diff] [blame] | 654 | |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 655 | itdevs = kzalloc(2 * sizeof(*itdevs), GFP_KERNEL); |
| 656 | if (itdevs == NULL) { |
Bartlomiej Zolnierkiewicz | ced3ec8 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 657 | printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev)); |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 658 | return -ENOMEM; |
Bartlomiej Zolnierkiewicz | eb7a07e | 2008-04-26 17:36:42 +0200 | [diff] [blame] | 659 | } |
| 660 | |
Bartlomiej Zolnierkiewicz | 04ba6e7 | 2008-07-24 22:53:32 +0200 | [diff] [blame] | 661 | rc = ide_pci_init_one(dev, &it821x_chipset, itdevs); |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 662 | if (rc) |
| 663 | kfree(itdevs); |
Bartlomiej Zolnierkiewicz | eb7a07e | 2008-04-26 17:36:42 +0200 | [diff] [blame] | 664 | |
Bartlomiej Zolnierkiewicz | 1d76d9d | 2008-07-24 22:53:16 +0200 | [diff] [blame] | 665 | return rc; |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 666 | } |
| 667 | |
Bartlomiej Zolnierkiewicz | 87d8b61 | 2008-07-24 22:53:22 +0200 | [diff] [blame] | 668 | static void __devexit it821x_remove(struct pci_dev *dev) |
| 669 | { |
| 670 | struct ide_host *host = pci_get_drvdata(dev); |
| 671 | struct it821x_dev *itdevs = host->host_priv; |
| 672 | |
| 673 | ide_pci_remove(dev); |
| 674 | kfree(itdevs); |
| 675 | } |
| 676 | |
Bartlomiej Zolnierkiewicz | 9cbcc5e | 2007-10-16 22:29:56 +0200 | [diff] [blame] | 677 | static const struct pci_device_id it821x_pci_tbl[] = { |
| 678 | { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 }, |
| 679 | { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 }, |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 680 | { 0, }, |
| 681 | }; |
| 682 | |
| 683 | MODULE_DEVICE_TABLE(pci, it821x_pci_tbl); |
| 684 | |
| 685 | static struct pci_driver driver = { |
| 686 | .name = "ITE821x IDE", |
| 687 | .id_table = it821x_pci_tbl, |
| 688 | .probe = it821x_init_one, |
Bartlomiej Zolnierkiewicz | 87d8b61 | 2008-07-24 22:53:22 +0200 | [diff] [blame] | 689 | .remove = it821x_remove, |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 690 | }; |
| 691 | |
| 692 | static int __init it821x_ide_init(void) |
| 693 | { |
| 694 | return ide_pci_register_driver(&driver); |
| 695 | } |
| 696 | |
Bartlomiej Zolnierkiewicz | 87d8b61 | 2008-07-24 22:53:22 +0200 | [diff] [blame] | 697 | static void __exit it821x_ide_exit(void) |
| 698 | { |
| 699 | pci_unregister_driver(&driver); |
| 700 | } |
| 701 | |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 702 | module_init(it821x_ide_init); |
Bartlomiej Zolnierkiewicz | 87d8b61 | 2008-07-24 22:53:22 +0200 | [diff] [blame] | 703 | module_exit(it821x_ide_exit); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 704 | |
| 705 | module_param_named(noraid, it8212_noraid, int, S_IRUGO); |
Paul Bolle | da19566 | 2008-04-17 01:14:33 +0200 | [diff] [blame] | 706 | MODULE_PARM_DESC(noraid, "Force card into bypass mode"); |
Alan Cox | da9091e | 2005-06-27 15:24:30 -0700 | [diff] [blame] | 707 | |
| 708 | MODULE_AUTHOR("Alan Cox"); |
| 709 | MODULE_DESCRIPTION("PCI driver module for the ITE 821x"); |
| 710 | MODULE_LICENSE("GPL"); |