wlan: Add WLAN driver config files
Beginning with JB MR1 the WLAN driver configuration files are stored
in the device project. This decouples these files from the driver,
and allows the driver to be built as part of the kernel.
Change-Id: Ic30b098e5bc99418e134fca9a7c62f2529a4c36c
diff --git a/WCNSS_qcom_cfg.ini b/WCNSS_qcom_cfg.ini
new file mode 100644
index 0000000..7014b48
--- /dev/null
+++ b/WCNSS_qcom_cfg.ini
@@ -0,0 +1,351 @@
+# This file allows user to override the factory
+
+# defaults for the WLAN Driver
+
+
+# Enable IMPS or not
+gEnableImps=1
+
+# Enable/Disable Idle Scan
+
+gEnableIdleScan=0
+
+
+# Increase sleep duration (seconds) during IMPS
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is
+# unnecessary if Idle Scan is disabled.
+gImpsModSleepTime=0
+
+
+# Enable BMPS or not
+gEnableBmps=1
+
+# Enable suspend or not
+
+# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+
+gEnableSuspend=3
+
+
+# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
+gDot11Mode=0
+
+
+# Handoff Enable(1) Disable(0)
+
+gEnableHandoff=0
+
+
+# CSR Roaming Enable(1) Disable(0)
+
+gRoamingTime=0
+
+
+# Assigned MAC Addresses - This will be used until NV items are in place
+
+# Each byte of MAC address is represented in Hex format as XX
+
+Intf0MacAddress=000AF58989FF
+Intf1MacAddress=000AF58989FE
+Intf2MacAddress=000AF58989FD
+
+Intf3MacAddress=000AF58989FC
+
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+
+InfraUapsdVoSrvIntv=0
+
+InfraUapsdViSrvIntv=0
+
+InfraUapsdBeSrvIntv=0
+
+InfraUapsdBkSrvIntv=0
+
+
+# Disable RSSI FW filtering
+
+gEnableFWRssiMonitoring=1
+
+
+# Make 1x1 the default antenna configuration
+
+gNumRxAnt=1
+
+
+# Beacon filtering frequency (unit in beacon intervals)
+
+gNthBeaconFilter=50
+
+
+# Enable WAPI or not
+
+# WAPIIsEnabled=0
+
+
+# Flags to filter Mcast abd Bcast RX packets.
+
+# Value 0: No filtering, 1: Filter all Multicast.
+
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+
+McastBcastFilter=0
+
+
+#Flag to enable HostARPOffload feature or not
+
+hostArpOffload=0
+
+
+#SoftAP Related Parameters
+
+# AP MAc addr
+
+gAPMacAddr=000AF589dcab
+
+
+# 802.11n Protection flag
+
+gEnableApProt=1
+
+
+#Enable OBSS protection
+
+gEnableApOBSSProt=0
+
+
+#Enable/Disable UAPSD for SoftAP
+
+gEnableApUapsd=0
+
+
+# Fixed Rate
+
+gFixedRate=0
+
+
+# Maximum Tx power
+
+# gTxPowerCap=30
+
+
+# Fragmentation Threshold
+
+# gFragmentationThreshold=2346
+
+
+# RTS threshold
+
+RTSThreshold=2347
+
+
+# Intra-BSS forward
+
+gDisableIntraBssFwd=0
+
+
+# WMM Enable/Disable
+
+WmmIsEnabled=0
+
+
+# 802.11d support
+
+g11dSupportEnabled=1
+
+# CCX Support and fast transition
+CcxEnabled=0
+FastTransitionEnabled=1
+ImplicitQosIsEnabled=1
+gNeighborScanTimerPeriod=200
+
+gNeighborLookupThreshold=76
+gNeighborReassocThreshold=81
+
+gNeighborScanChannelMinTime=20
+gNeighborScanChannelMaxTime=30
+gMaxNeighborReqTries=3
+
+# Legacy (non-CCX, non-802.11r) Fast Roaming Support
+# To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1
+# To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0
+FastRoamEnabled=1
+
+#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
+#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
+#the RSSI of the new/roamable AP should be for roaming
+RoamRssiDiff=3
+
+#Configure the RSSI gap that will be used to partition/categorize width of
+#each individual category (aka bucket).
+gRssiCatGap=5
+
+#Prefer 5GHz APs while roaming (default is gRoamPrefer5GHz=1)
+gRoamPrefer5GHz=1
+
+# SAP Country code
+
+# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
+
+# Example
+
+# US Indoor, USI
+
+# Korea Outdoor, KRO
+
+# Japan without optional byte, JP
+
+# France without optional byte, FR
+
+#gAPCntryCode=USI
+
+
+#Short Guard Interval Enable/disable
+
+gShortGI20Mhz=1
+
+gShortGI40Mhz=1
+
+
+#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
+
+gAPAutoShutOff=0
+
+
+# SAP auto channel selection configuration
+
+# 0 = disable auto channel selection
+
+# 1 = enable auto channel selection, channel provided by supplicant will be ignored
+
+gApAutoChannelSelection=0
+
+
+# Listen Energy Detect Mode Configuration
+
+# Valid values 0-128
+
+# 128 means disable Energy Detect feature
+
+# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+
+# 10-128 are reserved.
+
+# The EDET threshold mapping is as follows in 3dB step:
+
+# 0 = -60 dBm
+
+# 1 = -63 dBm
+
+# 2 = -66 dBm
+
+# ...
+
+# 7 = -81 dBm
+
+# 8 = -84 dBm
+
+# 9 = -87 dBm
+
+# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+
+#
+
+# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
+
+#
+
+gEnablePhyAgcListenMode=128
+
+
+#Preferred channel to start BT AMP AP mode (0 means, any channel)
+
+BtAmpPreferredChannel=0
+
+
+#Preferred band (both or 2.4 only or 5 only)
+
+BandCapability=0
+
+
+#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+
+enableBeaconEarlyTermination=0
+
+beaconEarlyTerminationWakeInterval=3
+
+
+#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
+
+gEnableBtAmp=0
+
+
+#SOFTAP Channel Range selection
+
+gAPChannelSelectStartChannel=1
+
+gAPChannelSelectEndChannel=11
+
+
+#SOFTAP Channel Range selection Operating band
+
+# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
+
+gAPChannelSelectOperatingBand=0
+
+
+#Channel Bonding
+gChannelBondingMode5GHz=6
+
+
+#Enable Keep alive with non-zero period value
+
+#gStaKeepAlivePeriod = 30
+
+
+#If set will start with active scan after driver load, otherwise will start with
+
+#passive scan to find out the domain
+
+#gEnableBypass11d=1
+
+
+#If set to 0, will not scan DFS channels
+
+gEnableDFSChnlScan=1
+
+
+gVhtChannelWidth=2
+gEnableLogp=1
+
+
+# Enable Automatic Tx Power control
+
+gEnableAutomaticTxPowerControl=1
+
+# 0 for OLPC 1 for CLPC and SCPC
+gEnableCloseLoop=1
+
+#Data Inactivity Timeout when in powersave (in ms)
+gDataInactivityTimeout=200
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+gEnableLpwrImgTransition=1
+
+# Enable Tx beamforming
+gTxBFEnable=1
+
+# Enable Tx LDPC
+#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
+gTxLdpcEnable=3
+
+END
+
+# Note: Configuration parser would not read anything past the END marker
+