Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 1 | # This file allows user to override the factory |
| 2 | |
| 3 | # defaults for the WLAN Driver |
| 4 | |
| 5 | |
| 6 | # Enable IMPS or not |
| 7 | gEnableImps=1 |
| 8 | |
| 9 | # Enable/Disable Idle Scan |
| 10 | |
| 11 | gEnableIdleScan=0 |
| 12 | |
| 13 | |
| 14 | # Increase sleep duration (seconds) during IMPS |
| 15 | # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| 16 | # unnecessary if Idle Scan is disabled. |
| 17 | gImpsModSleepTime=0 |
| 18 | |
| 19 | |
| 20 | # Enable BMPS or not |
| 21 | gEnableBmps=1 |
| 22 | |
| 23 | # Enable suspend or not |
| 24 | |
| 25 | # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| 26 | |
| 27 | gEnableSuspend=3 |
| 28 | |
| 29 | |
| 30 | # Phy Mode (auto, b, g, n, etc) |
| 31 | # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| 32 | gDot11Mode=0 |
| 33 | |
| 34 | |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 35 | # CSR Roaming Enable(1) Disable(0) |
| 36 | |
| 37 | gRoamingTime=0 |
| 38 | |
| 39 | |
| 40 | # Assigned MAC Addresses - This will be used until NV items are in place |
| 41 | |
| 42 | # Each byte of MAC address is represented in Hex format as XX |
| 43 | |
| 44 | Intf0MacAddress=000AF58989FF |
| 45 | Intf1MacAddress=000AF58989FE |
| 46 | Intf2MacAddress=000AF58989FD |
| 47 | |
| 48 | Intf3MacAddress=000AF58989FC |
| 49 | |
| 50 | |
| 51 | # UAPSD service interval for VO,VI, BE, BK traffic |
| 52 | |
| 53 | InfraUapsdVoSrvIntv=0 |
| 54 | |
| 55 | InfraUapsdViSrvIntv=0 |
| 56 | |
| 57 | InfraUapsdBeSrvIntv=0 |
| 58 | |
| 59 | InfraUapsdBkSrvIntv=0 |
| 60 | |
Sandeep Puligilla | a5e6f05 | 2013-11-27 00:55:22 +0530 | [diff] [blame] | 61 | # Flag to allow STA send AddTspec even when ACM is Off |
| 62 | gAddTSWhenACMIsOff=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 63 | |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 64 | # Make 1x1 the default antenna configuration |
| 65 | |
| 66 | gNumRxAnt=1 |
| 67 | |
| 68 | |
| 69 | # Beacon filtering frequency (unit in beacon intervals) |
| 70 | |
| 71 | gNthBeaconFilter=50 |
| 72 | |
| 73 | |
| 74 | # Enable WAPI or not |
| 75 | |
| 76 | # WAPIIsEnabled=0 |
| 77 | |
| 78 | |
| 79 | # Flags to filter Mcast abd Bcast RX packets. |
| 80 | |
| 81 | # Value 0: No filtering, 1: Filter all Multicast. |
| 82 | |
| 83 | # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| 84 | |
Madan Mohan Koyyalamudi | a486bbf | 2013-08-27 14:12:44 -0700 | [diff] [blame] | 85 | McastBcastFilter=3 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 86 | |
| 87 | |
| 88 | #Flag to enable HostARPOffload feature or not |
| 89 | |
Gopichand Nakkala | 4f7e5eb | 2013-03-14 18:00:29 -0700 | [diff] [blame] | 90 | hostArpOffload=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 91 | |
| 92 | |
| 93 | #SoftAP Related Parameters |
| 94 | |
| 95 | # AP MAc addr |
| 96 | |
| 97 | gAPMacAddr=000AF589dcab |
| 98 | |
| 99 | |
| 100 | # 802.11n Protection flag |
| 101 | |
| 102 | gEnableApProt=1 |
| 103 | |
| 104 | |
| 105 | #Enable OBSS protection |
| 106 | |
Leela Venkata Kiran Kumar Reddy Chirala | 0d44e11 | 2014-01-08 18:54:04 -0800 | [diff] [blame] | 107 | gEnableApOBSSProt=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 108 | |
| 109 | |
| 110 | #Enable/Disable UAPSD for SoftAP |
| 111 | |
Naresh Jayaram | 867ad37 | 2014-01-24 21:57:08 +0530 | [diff] [blame] | 112 | gEnableApUapsd=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 113 | |
| 114 | |
| 115 | # Fixed Rate |
| 116 | |
| 117 | gFixedRate=0 |
| 118 | |
| 119 | |
| 120 | # Maximum Tx power |
| 121 | |
| 122 | # gTxPowerCap=30 |
| 123 | |
| 124 | |
| 125 | # Fragmentation Threshold |
| 126 | |
| 127 | # gFragmentationThreshold=2346 |
| 128 | |
| 129 | |
| 130 | # RTS threshold |
| 131 | |
| 132 | RTSThreshold=2347 |
| 133 | |
| 134 | |
| 135 | # Intra-BSS forward |
| 136 | |
| 137 | gDisableIntraBssFwd=0 |
| 138 | |
| 139 | |
| 140 | # WMM Enable/Disable |
| 141 | |
| 142 | WmmIsEnabled=0 |
| 143 | |
| 144 | |
| 145 | # 802.11d support |
| 146 | |
| 147 | g11dSupportEnabled=1 |
| 148 | |
| 149 | # CCX Support and fast transition |
| 150 | CcxEnabled=0 |
| 151 | FastTransitionEnabled=1 |
Sandeep Puligilla | a5e6f05 | 2013-11-27 00:55:22 +0530 | [diff] [blame] | 152 | ImplicitQosIsEnabled=0 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 153 | gNeighborScanTimerPeriod=200 |
| 154 | |
Bansidhar Gopalchari | 0a59be1 | 2013-06-21 22:06:36 -0700 | [diff] [blame] | 155 | gNeighborLookupThreshold=78 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 156 | |
| 157 | gNeighborScanChannelMinTime=20 |
| 158 | gNeighborScanChannelMaxTime=30 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 159 | |
| 160 | # Legacy (non-CCX, non-802.11r) Fast Roaming Support |
Bansidhar Gopalchari | 0a59be1 | 2013-06-21 22:06:36 -0700 | [diff] [blame] | 161 | # To enable, set FastRoamEnabled=1 |
| 162 | # To disable, set FastRoamEnabled=0 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 163 | FastRoamEnabled=1 |
| 164 | |
| 165 | #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| 166 | #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| 167 | #the RSSI of the new/roamable AP should be for roaming |
Bansidhar Gopalchari | 0a59be1 | 2013-06-21 22:06:36 -0700 | [diff] [blame] | 168 | RoamRssiDiff=5 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 169 | |
| 170 | # SAP Country code |
| 171 | |
| 172 | # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| 173 | |
| 174 | # Example |
| 175 | |
| 176 | # US Indoor, USI |
| 177 | |
| 178 | # Korea Outdoor, KRO |
| 179 | |
| 180 | # Japan without optional byte, JP |
| 181 | |
| 182 | # France without optional byte, FR |
| 183 | |
| 184 | #gAPCntryCode=USI |
| 185 | |
| 186 | |
| 187 | #Short Guard Interval Enable/disable |
| 188 | |
| 189 | gShortGI20Mhz=1 |
| 190 | |
| 191 | gShortGI40Mhz=1 |
| 192 | |
| 193 | |
| 194 | #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| 195 | |
| 196 | gAPAutoShutOff=0 |
| 197 | |
| 198 | |
| 199 | # SAP auto channel selection configuration |
| 200 | |
| 201 | # 0 = disable auto channel selection |
| 202 | |
| 203 | # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| 204 | |
Kiet Lam | f5b1bd8 | 2014-02-26 18:03:28 -0800 | [diff] [blame] | 205 | gApAutoChannelSelection=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 206 | |
| 207 | |
| 208 | # Listen Energy Detect Mode Configuration |
| 209 | |
| 210 | # Valid values 0-128 |
| 211 | |
| 212 | # 128 means disable Energy Detect feature |
| 213 | |
| 214 | # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| 215 | |
| 216 | # 10-128 are reserved. |
| 217 | |
| 218 | # The EDET threshold mapping is as follows in 3dB step: |
| 219 | |
| 220 | # 0 = -60 dBm |
| 221 | |
| 222 | # 1 = -63 dBm |
| 223 | |
| 224 | # 2 = -66 dBm |
| 225 | |
| 226 | # ... |
| 227 | |
| 228 | # 7 = -81 dBm |
| 229 | |
| 230 | # 8 = -84 dBm |
| 231 | |
| 232 | # 9 = -87 dBm |
| 233 | |
| 234 | # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| 235 | |
| 236 | # |
| 237 | |
| 238 | # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| 239 | |
| 240 | # |
| 241 | |
| 242 | gEnablePhyAgcListenMode=128 |
| 243 | |
| 244 | |
| 245 | #Preferred channel to start BT AMP AP mode (0 means, any channel) |
| 246 | |
| 247 | BtAmpPreferredChannel=0 |
| 248 | |
| 249 | |
| 250 | #Preferred band (both or 2.4 only or 5 only) |
| 251 | |
| 252 | BandCapability=0 |
| 253 | |
| 254 | |
| 255 | #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| 256 | |
Gopichand Nakkala | 4f7e5eb | 2013-03-14 18:00:29 -0700 | [diff] [blame] | 257 | enableBeaconEarlyTermination=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 258 | |
Gopichand Nakkala | 4f7e5eb | 2013-03-14 18:00:29 -0700 | [diff] [blame] | 259 | beaconEarlyTerminationWakeInterval=11 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 260 | |
| 261 | |
| 262 | #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) |
| 263 | |
| 264 | gEnableBtAmp=0 |
| 265 | |
| 266 | |
| 267 | #SOFTAP Channel Range selection |
| 268 | |
| 269 | gAPChannelSelectStartChannel=1 |
| 270 | |
| 271 | gAPChannelSelectEndChannel=11 |
| 272 | |
| 273 | |
| 274 | #SOFTAP Channel Range selection Operating band |
| 275 | |
| 276 | # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| 277 | |
| 278 | gAPChannelSelectOperatingBand=0 |
| 279 | |
| 280 | |
| 281 | #Channel Bonding |
Madan Mohan Koyyalamudi | ca01dab | 2013-09-04 11:56:53 -0700 | [diff] [blame] | 282 | gChannelBondingMode5GHz=1 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 283 | |
| 284 | |
| 285 | #Enable Keep alive with non-zero period value |
| 286 | |
Madan Mohan Koyyalamudi | ca01dab | 2013-09-04 11:56:53 -0700 | [diff] [blame] | 287 | gStaKeepAlivePeriod=30 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 288 | |
Gopichand Nakkala | 4f7e5eb | 2013-03-14 18:00:29 -0700 | [diff] [blame] | 289 | |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 290 | #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| 291 | #For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| 292 | #For both active and power save clients. |
Gopichand Nakkala | 4f7e5eb | 2013-03-14 18:00:29 -0700 | [diff] [blame] | 293 | |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 294 | #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| 295 | #If doesn't honor for 5 seconds then Driver remove client. |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 296 | |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 297 | #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on |
| 298 | #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. |
| 299 | #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod).. |
| 300 | |
| 301 | #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| 302 | #where we send NULL frame. |
| 303 | |
AnjaneeDevi Kapparapu | 3ac429f | 2014-02-27 14:32:44 +0530 | [diff] [blame] | 304 | gApLinkMonitorPeriod = 30 |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 305 | |
AnjaneeDevi Kapparapu | 3ac429f | 2014-02-27 14:32:44 +0530 | [diff] [blame] | 306 | gGoLinkMonitorPeriod = 10 |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 307 | |
| 308 | #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| 309 | #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| 310 | #gGoKeepAlivePeriod = 5 |
| 311 | |
| 312 | #gApKeepAlivePeriod = 5 |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 313 | #If set will start with active scan after driver load, otherwise will start with |
| 314 | |
| 315 | #passive scan to find out the domain |
| 316 | |
| 317 | #gEnableBypass11d=1 |
| 318 | |
| 319 | |
| 320 | #If set to 0, will not scan DFS channels |
| 321 | |
| 322 | gEnableDFSChnlScan=1 |
| 323 | |
| 324 | |
| 325 | gVhtChannelWidth=2 |
| 326 | gEnableLogp=1 |
| 327 | |
| 328 | |
| 329 | # Enable Automatic Tx Power control |
| 330 | |
| 331 | gEnableAutomaticTxPowerControl=1 |
| 332 | |
| 333 | # 0 for OLPC 1 for CLPC and SCPC |
| 334 | gEnableCloseLoop=1 |
| 335 | |
| 336 | #Data Inactivity Timeout when in powersave (in ms) |
| 337 | gDataInactivityTimeout=200 |
| 338 | |
| 339 | # VHT Tx/Rx MCS values |
| 340 | # Valid values are 0,1,2. If commented out, the default value is 0. |
| 341 | # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| 342 | gVhtRxMCS=2 |
| 343 | gVhtTxMCS=2 |
| 344 | |
| 345 | gEnableLpwrImgTransition=1 |
| 346 | |
| 347 | # Enable Tx beamforming |
| 348 | gTxBFEnable=1 |
| 349 | |
| 350 | # Enable Tx LDPC |
| 351 | #gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT |
| 352 | gTxLdpcEnable=3 |
| 353 | |
Madan Mohan Koyyalamudi | bc08801 | 2013-08-06 20:48:27 -0700 | [diff] [blame] | 354 | #FlexConnect Power Factor |
| 355 | #Default is set to 0 (disable) |
| 356 | gFlexConnectPowerFactor=0 |
| 357 | |
Madan Mohan Koyyalamudi | db54a70 | 2013-08-15 15:23:45 -0700 | [diff] [blame] | 358 | # Valid values are 2048,4096,8192 and so on |
| 359 | # Please don't use values other than the ones mentioned above |
| 360 | gMaxMediumTime=4096 |
| 361 | |
Madan Mohan Koyyalamudi | 0a2ba9a | 2013-09-17 20:12:25 -0700 | [diff] [blame] | 362 | # 802.11K support |
| 363 | gRrmEnable=1 |
| 364 | gRrmOperChanMax=8 |
| 365 | gRrmNonOperChanMax=8 |
| 366 | gRrmRandIntvl=100 |
| 367 | |
AnjaneeDevi Kapparapu | 3ac429f | 2014-02-27 14:32:44 +0530 | [diff] [blame] | 368 | #Enable/Disable Modulated DTIM feature |
| 369 | gEnableModulatedDTIM=3 |
| 370 | |
| 371 | #max LI value for modulated DTIM |
| 372 | gMaxLIModulatedDTIM=3 |
| 373 | |
Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame] | 374 | END |
| 375 | |
| 376 | # Note: Configuration parser would not read anything past the END marker |
| 377 | |